Search Results

Search found 7371 results on 295 pages for 'raid card'.

Page 9/295 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

  • RAID-capable 3.5" SATA Drives

    - by nroam
    I recently purchased a pair of 1TB Western Digital WD1002FBYS RE3 drives for use in an external RAID enclosure. I have found that they tend to drop out of the array after a while. Thinking it was the enclosure I tried them on another one but found the same issue. So a bit of googling and I found http://www.tomshardware.com/forum/251076-32-raid-issues-western-digital-hard-disk which suggests that: "WD's "RE" (RAID Edition) HDDs support Time-Limited Error Recovery ("TLER" ): http://www.wdc.com/en/products/productcatalog.asp?language=en As a non-TLER HDD fills up with data, the error detection firmware might take too long, and the RAID controller may drop that HDD from a RAID array." So now I wonder what SATA drives have firmware which is compatible with RAID arrays (esp. RAID 1, 5, but not 0)? I have not been able to come up with the magic set of keywords to ellicit the answer from Google. However, various sites suggest that Seagate & Hitachi are in general OK. Does anyone have any generic (or even specific) guidance on how to work out if a drive's firmware may harbour code that is potentially an issue in a RAID0 setting other than stating that it must be 'enterprise' ready?

    Read the article

  • No GLX on Intel card with multiseat with additional nVidia card

    - by MeanEYE
    I have multiseat configured and my Xorg has 2 server layouts. One is for nVidia card and other is for Intel card. They both work, but display server assigned to Intel card doesn't have hardware acceleration since DRI and GLX module being used is from nVidia driver. So my question is, can I configure layouts somehow to use right DRI and GLX with each card? My Xorg.conf: Section "ServerLayout" Identifier "Default" Screen 0 "Screen0" 0 0 Option "Xinerama" "0" EndSection Section "ServerLayout" Identifier "TV" Screen 0 "Screen1" 0 0 Option "Xinerama" "0" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E198WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 610" EndSection Section "Device" Identifier "Device1" Driver "intel" BusID "PCI:0:2:0" Option "AccelMethod" "uxa" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "nvidiaXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-0: nvidia-auto-select +1440+0, DFP-1: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Log file for Intel: [ 18.239] X.Org X Server 1.13.0 Release Date: 2012-09-05 [ 18.239] X Protocol Version 11, Revision 0 [ 18.239] Build Operating System: Linux 2.6.24-32-xen x86_64 Ubuntu [ 18.239] Current Operating System: Linux bytewiper 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 [ 18.239] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-18-generic root=UUID=fc0616fd-f212-4846-9241-ba4a492f0513 ro quiet splash [ 18.239] Build Date: 20 September 2012 11:55:20AM [ 18.239] xorg-server 2:1.13.0+git20120920.70e57668-0ubuntu0ricotz (For technical support please see http://www.ubuntu.com/support) [ 18.239] Current version of pixman: 0.26.0 [ 18.239] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 18.239] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 18.239] (==) Log file: "/var/log/Xorg.1.log", Time: Wed Nov 21 18:32:14 2012 [ 18.239] (==) Using config file: "/etc/X11/xorg.conf" [ 18.239] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 18.239] (++) ServerLayout "TV" [ 18.239] (**) |-->Screen "Screen1" (0) [ 18.239] (**) | |-->Monitor "Monitor1" [ 18.240] (**) | |-->Device "Device1" [ 18.240] (**) Option "Xinerama" "0" [ 18.240] (==) Automatically adding devices [ 18.240] (==) Automatically enabling devices [ 18.240] (==) Automatically adding GPU devices [ 18.240] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/Type1, built-ins [ 18.240] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" [ 18.240] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 18.240] (II) Loader magic: 0x7f6917944c40 [ 18.240] (II) Module ABI versions: [ 18.240] X.Org ANSI C Emulation: 0.4 [ 18.240] X.Org Video Driver: 13.0 [ 18.240] X.Org XInput driver : 18.0 [ 18.240] X.Org Server Extension : 7.0 [ 18.240] (II) config/udev: Adding drm device (/dev/dri/card0) [ 18.241] (--) PCI: (0:0:2:0) 8086:0152:1043:84ca rev 9, Mem @ 0xf7400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64 [ 18.241] (--) PCI:*(0:1:0:0) 10de:104a:1458:3546 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/134217728, 0xe8000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288 [ 18.241] (II) Open ACPI successful (/var/run/acpid.socket) [ 18.241] Initializing built-in extension Generic Event Extension [ 18.241] Initializing built-in extension SHAPE [ 18.241] Initializing built-in extension MIT-SHM [ 18.241] Initializing built-in extension XInputExtension [ 18.241] Initializing built-in extension XTEST [ 18.241] Initializing built-in extension BIG-REQUESTS [ 18.241] Initializing built-in extension SYNC [ 18.241] Initializing built-in extension XKEYBOARD [ 18.241] Initializing built-in extension XC-MISC [ 18.241] Initializing built-in extension SECURITY [ 18.241] Initializing built-in extension XINERAMA [ 18.241] Initializing built-in extension XFIXES [ 18.241] Initializing built-in extension RENDER [ 18.241] Initializing built-in extension RANDR [ 18.241] Initializing built-in extension COMPOSITE [ 18.241] Initializing built-in extension DAMAGE [ 18.241] Initializing built-in extension MIT-SCREEN-SAVER [ 18.241] Initializing built-in extension DOUBLE-BUFFER [ 18.241] Initializing built-in extension RECORD [ 18.241] Initializing built-in extension DPMS [ 18.241] Initializing built-in extension X-Resource [ 18.241] Initializing built-in extension XVideo [ 18.241] Initializing built-in extension XVideo-MotionCompensation [ 18.241] Initializing built-in extension XFree86-VidModeExtension [ 18.241] Initializing built-in extension XFree86-DGA [ 18.241] Initializing built-in extension XFree86-DRI [ 18.241] Initializing built-in extension DRI2 [ 18.241] (II) LoadModule: "glx" [ 18.241] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/libglx.so [ 18.247] (II) Module glx: vendor="NVIDIA Corporation" [ 18.247] compiled for 4.0.2, module version = 1.0.0 [ 18.247] Module class: X.Org Server Extension [ 18.247] (II) NVIDIA GLX Module 310.19 Thu Nov 8 01:12:43 PST 2012 [ 18.247] Loading extension GLX [ 18.247] (II) LoadModule: "intel" [ 18.248] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so [ 18.248] (II) Module intel: vendor="X.Org Foundation" [ 18.248] compiled for 1.13.0, module version = 2.20.13 [ 18.248] Module class: X.Org Video Driver [ 18.248] ABI class: X.Org Video Driver, version 13.0 [ 18.248] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale, Sandybridge Desktop (GT1), Sandybridge Desktop (GT2), Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1), Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+), Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2), Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server, Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2), Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2), Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2), Haswell Server (GT2+), Haswell SDV Desktop (GT1), Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+), Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2), Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1), Haswell SDV Server (GT2), Haswell SDV Server (GT2+), Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2), Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1), Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+), Haswell ULT Server (GT1), Haswell ULT Server (GT2), Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1), Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+), Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2), Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1), Haswell CRW Server (GT2), Haswell CRW Server (GT2+), ValleyView PO board [ 18.248] (++) using VT number 8 [ 18.593] (II) intel(0): using device path '/dev/dri/card0' [ 18.593] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 18.593] (==) intel(0): RGB weight 888 [ 18.593] (==) intel(0): Default visual is TrueColor [ 18.593] (**) intel(0): Option "AccelMethod" "uxa" [ 18.593] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Desktop (GT1) [ 18.593] (**) intel(0): Relaxed fencing enabled [ 18.593] (**) intel(0): Wait on SwapBuffers? enabled [ 18.593] (**) intel(0): Triple buffering? enabled [ 18.593] (**) intel(0): Framebuffer tiled [ 18.593] (**) intel(0): Pixmaps tiled [ 18.593] (**) intel(0): 3D buffers tiled [ 18.593] (**) intel(0): SwapBuffers wait enabled ... [ 20.312] (II) Module fb: vendor="X.Org Foundation" [ 20.312] compiled for 1.13.0, module version = 1.0.0 [ 20.312] ABI class: X.Org ANSI C Emulation, version 0.4 [ 20.312] (II) Loading sub module "dri2" [ 20.312] (II) LoadModule: "dri2" [ 20.312] (II) Module "dri2" already built-in [ 20.312] (==) Depth 24 pixmap format is 32 bpp [ 20.312] (II) intel(0): [DRI2] Setup complete [ 20.312] (II) intel(0): [DRI2] DRI driver: i965 [ 20.312] (II) intel(0): Allocated new frame buffer 1920x1080 stride 7680, tiled [ 20.312] (II) UXA(0): Driver registered support for the following operations: [ 20.312] (II) solid [ 20.312] (II) copy [ 20.312] (II) composite (RENDER acceleration) [ 20.312] (II) put_image [ 20.312] (II) get_image [ 20.312] (==) intel(0): Backing store disabled [ 20.312] (==) intel(0): Silken mouse enabled [ 20.312] (II) intel(0): Initializing HW Cursor [ 20.312] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 20.313] (**) intel(0): DPMS enabled [ 20.313] (==) intel(0): Intel XvMC decoder enabled [ 20.313] (II) intel(0): Set up textured video [ 20.313] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 20.313] (II) intel(0): direct rendering: DRI2 Enabled [ 20.313] (==) intel(0): hotplug detection: "enabled" [ 20.332] (--) RandR disabled [ 20.335] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 20.335] (II) intel(0): Setting screen physical size to 508 x 285 [ 20.338] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm [ 20.340] (II) config/udev: Adding input device Power Button (/dev/input/event1) [ 20.340] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 20.340] (II) LoadModule: "evdev" [ 20.340] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so

    Read the article

  • Hardware RAID Controller Support for SSD TRIM

    - by dss539
    Do any hardware RAID controllers available today support TRIM? If not, do any manufacturers have target dates for supporting TRIM? Should I even care about TRIM for SSDs installed in performance-sensitive workstations? Before you suggest it, yes software RAID would sidestep the issue, but my requirements do not allow software RAID. edit: The answer appears to be "no RAID controllers support TRIM" at the current date.

    Read the article

  • What is the SCSI RAID channels?

    - by erthad
    What is the SCSI RAID channels? I.e. what is the difference between, say, 1-channel RAID controller and 2-channel RAID controller? Is it for data throughput, number of RAID arrays I can create on controller, number of disks I can plug into controller or what else?

    Read the article

  • Software Raid 10 on VirtualBox?

    - by user791022
    I want to learn how to use Software Raid 10, is it possible to use VirtualBox by adding four storage images? This is my plan: 4x 100mb partitions (1 on each drive) configured as a raid 1 for /boot in ext3. Then with the remaining space on each drive, setup a software raid partition and configure it to to LVM and raid 10. In the LVM, set up a 4gb swap partition and the remaining space as the root partition ( / ) as ext3.

    Read the article

  • Two Raid 1s in a single system?

    - by DebAtCQ
    I'm building a Raid array for the first time in my system and I have a question regarding having multiple Raid 1 arrays in a single Win 7 system. I'm a bit of an organizational freak with my data and I currently have two separate hard drives I want to mirror. The new motherboard I'm looking to buy supports Raid, so my question is this: a) can I have more than one Raid 1 array in a single system? b) would I have to buy a separate controller for the second array?

    Read the article

  • Two Raid-1 arrays in a single system?

    - by DebAtCQ
    I'm building a Raid array for the first time in my system and I have a question regarding having multiple Raid-1 arrays in a single Win 7 system. I'm a bit of an organizational freak with my data and I currently have two separate hard drives I want to mirror. The new motherboard I'm looking to buy supports Raid, so my questions are: Can I have more than one Raid-1 array in a single system? Would I have to buy a separate controller for the second array?

    Read the article

  • raid 0 failure, drives look fine

    - by Alan
    Hello, after a lovely blue screen my vista 64 machine decided to reconfigure one of my drives to no longer be part of my raid volume. So now my raid fails as it only has one member disk. This happened to me about 6 months ago and I just changed the disk in question back to a raid disk and all was well. However I cant seem to find that option in my bios or raid config anymore :( Any help would be appreciated

    Read the article

  • How to disable automatic and forced fsck on disks in a linux software raid?

    - by mit
    This is the /etc/fstab entry of a raid system /dev/md4 that is controlled with mdadm and webmin on an ubuntu 10.04 64 server: /dev/md4 /mnt/md4 ext3 relatime 0 0 We tried to switch off automatic forced fsck on rebotts, as we prefer to implement our own scheduled fsck routine by setting the last parameter of the line to 0 (ZERO). But we found out the forced and automatic check still occurs on the underlying real disks, lets say sdb1 and sdc1. How can we switch that off?

    Read the article

  • raid 0 failure, drives look fine

    - by Alan
    Hello, after a lovely blue screen my vista 64 machine decided to reconfigure one of my drives to no longer be part of my raid volume. So now my raid fails as it only has one member disk. This happened to me about 6 months ago and I just changed the disk in question back to a raid disk and all was well. However I cant seem to find that option in my bios or raid config anymore :( Any help would be appreciated

    Read the article

  • Mobility Card in Bangalore for Transportation

    - by Rekha
    Transport Minister R Ashoka announced Bangalore Metropolitan Transport Corporation (BMTC) services are going to be best in the world soon. BMTC has planned to launch a Mobility Card with which commuters can get rides in BMTC, KSRTC and future Metro Train facilities without buying tickets for each ride. The conductor with have a simple device in which the commuters can swipe their cards to deduct the ticket tarrif for bus or metro rides automatically. This Mobility card can be obtained by paying a fixed amount. This method is time saving and the commuters can be saved from paying the exact change for tickets. Ashoka says the Volvo Vayu Vaira services have internet connectivity and voice announcements of every bus stop names and this has been appreciated by the commuters. With WiFi Connections in Shatabdi Trains soon and Mobility Cards, India is soon to match the services of US Standards. Government officials are keen in implementing these services before the end of this year. Hope all these services are well used and maintained.   This article titled,Mobility Card in Bangalore for Transportation, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

    Read the article

  • SD Card only mounted after a reboot

    - by hattenn
    I have a Kingston 2GB MicroSD and I plug it in via an inconix MicroSD Adapter to the internal card reader of my Samsung N210 Netbook with Ubuntu 10.10, but it doesn't show up. Only if I reboot the system when the card's plugged in it shows up. Why does it need a reboot for mounting? sudo fdisk -l gives the output below. But I can only see the drive when I reboot the computer while the card's plugged. Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x9a5a7990 Device Boot Start End Blocks Id System /dev/sda1 1 1959 15728640 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 * 1959 1972 102400 7 HPFS/NTFS /dev/sda3 1972 18992 136718750 83 Linux /dev/sda4 18992 19458 3738625 5 Extended /dev/sda5 18992 19458 3738624 82 Linux swap / Solaris Disk /dev/sdb: 1973 MB, 1973420032 bytes 60 heads, 59 sectors/track, 1088 cylinders Units = cylinders of 3540 * 512 = 1812480 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 1089 1927100+ 6 FAT16

    Read the article

  • RAID 5 RECONSTRUCT with RAID Reconstructor

    - by user22914
    I have Dell Poweredge server 2600 with Raid 5 in 3 hard drive Scsi 36gb each, it was fail to boot sinc the third drive is offline. I attached Sata card adapter to Sata hard drive and install OS SERVER 2003 to it, downloaded drivers for Raid and everything goes fine when I use recovery data software called "GetDataBack" from here http://www.runtime.org/data-recovery-software.htm but the problem that not all data recovered, I am still looking for importants data with about 5 GB size. I have another software called "RAID Reconstructor" from "http://www.runtime.org/raid.htm" I thought if I run it to reconstruct that will help to recover more data and put the third drive to be Online but I am afraid that might erase the current data in the other drives. Please I need your advise in how I could retrive the remaining data? Thanks

    Read the article

  • Getting VMWare ESXi 5.0.0 with RAID using the Intel X79 chipset to work

    - by Deleted
    I have bought a new server where I use the motherboard ASUS P9X79 WS X79 S-2011 ATX. It will be used for virtualization, preferably using VMware vSphere Hypervisor™ (ESXi) if I can get the RAID on my motherboard working with VMWare (it does not detect it). The motherboard has the Intel® X79 chipset, which for RAID controller means vendor ID 8086 (Intel) and model ID 2826. When I boot the ESXi 5.0.0 installation media from my flash drive I can not see drives in the RAID5 set I created. Questions: Is there a VIB file for the RAID controller I can use? I have found one article at http://www.intel.com/support/motherboards/server/sb/CS-033313.htm on getting RAID to work with some Intel controllers, it lists 9 integrated RAID modules it is comptabile with. However, there is no mention of the X79 chipset.

    Read the article

  • Reconfigure RAID on Dell PowerEdge T710

    - by Stefano Borini
    I have a Dell PowerEdge T710 under my feet at this very moment, with RedHat Enterprise Server 5.3. I have 6 1TB disks and two 500GB. parted reports two devices, one 500 GB and the other 4 TB. So I assume the RAID has been setup as mirror for two disks, and I assume as RAID 5 the remaining ones. I say "I assume" because it does not make sense. Having 6 disks in RAID 5, I should obtain a total space of 5 TB, not 4TB. It's not even RAID 10: I would end up with a 3 TB unit. How can I check and eventually modify the RAID array definition? In the Fujitsu Siemens I played with some time ago, at boot I had the chance to enter the controller BIOS, but here I don't see a clear way to perform this operation.

    Read the article

  • Advantages of multiple SQL Server files with a single RAID array

    - by Dr Giles M
    Originally posted on stack overflow, but re-worded. Imagine the scenario : For a database I have RAID arrays R: (MDF) T: (transaction log) and of course shared transparent usage of X: (tempDB). I've been reading around and get the impression that if you are using RAID then adding multiple SQL Server NDF files sitting on R: within a filegroup won't yeild any more improvements. Of course, adding another raid array S: and putting an NDF file on that would. However, being a reasonably savvy software person, it's not unthinkable to hypothesise that, even for smaller MDFs sitting on one RAID array that SQL Server will perform growth and locking operations (for writes) on the MDF, so adding NDFs to the filegroup even if they sat on R: would distribute the locking operations and growth operations allowing more throughput? Or does the time taken to reconstruct the data from distributed filegroups outweigh the benefits of reduced locking? I'm also aware that the behaviour and benefits may be different for tables/indeces/log. Is there a good site that distinguishes the benefits of multiple files when RAID is already in place?

    Read the article

  • Do I need to rebuild the array after putting in a new hot spare?

    - by Shade34321
    So my experience with RAID is minimal. So I figured I'd come and ask here. We have a 16 drive RAID system that have 15 drives in RAID 5 with a hot spare left over. Recently one of the drives in the RAID was giving errors so I cloned it over to the hot spare and put a new drive in it's spot. I made the new drive the hot spare as I was told. I was told to rebuild the array after putting in the new drive as a hot spare so I tried and wasn't able to. So my question is do I need to rebuild it and if so why did it tell me I couldn't. Thanks! UPDATE: So I've come back up to work and looked at the RAID and it pulled in the hot spare into the raid and kicked out another drive.

    Read the article

  • How to enable raid on Gigabyte G33M-S2L?

    - by Wabbitseason
    I'd like to set up RAID-1 on my Gigabyte G33M-S2L motherboard and for this reason I purchased two 1T hard drives. According to SiSoft Sandra the motherboard does support RAID but it is disabled. I looked everywhere in BIOS even upgraded it to the most recent version but found nothing that would have said "RAID" and the operating system I wish to install sees the two HDDs, not just a RAIDed one. What could be the problem? Does my motherboard support RAID (as the diagnostic tool claims) or do I need to buy a RAID card?

    Read the article

  • Will disk cloning resolve bad stripes on RAID?

    - by user13323
    Hi. We have a logical RAID1 drive in bad stripes state, which kept that status even after replacement and rebuilding of both drives, and gives errors in Windows logs about failure of writing to disk. IBM support suggests erasing and re-creating the RAID, then re-installing the Windows. The resulting down-time unacceptible for us, so we want to clone the RAID (via Acronis True Image), erase and re-create the RAID, then dump the cloned data back. Following IBM logic where RAID erasing and re-creation resets the whole RAID meta-data, this should clear the bad-stripes status, and start from a blank page. Question is if such strategy is possible, and will produce the desired effect? Any idea is appreciated - thanks in advance!

    Read the article

  • Openfiler RAID 10 option not found

    - by chrisling106
    Hi, I'm building a NAS using Openfiler2.3 (from 32-bit ISO), first of all I want to experiment it on VM first before going out and buy the harddrives needed. I created 5 virtual drives on VMware, sda is 2GB and the rest 1GB each (sdb to sde). I left sda blank and want to setup a RAID 10 disk using sdb, sdc, sdd and sde, 4 RAID partitions are setup successfully, but when I try to create a RAID device the only option for RAID level is 1, 0, 5 and 6. RAID 10 is not there! Can someone let me know what have I missed, please? TIA.

    Read the article

  • Does RAID 1 protect against corruption?

    - by Shaun
    Does Raid 1 protect against data corruption? For example, let's say that I am keeping all of my important files on a NAS that uses 2 disks in a RAID 1. If one hard drive has some kind of internal problem and the data becomes corrupted, does the RAID recognize this automatically and correct it using data from the other good disk? Could it even know which copy is the good one? Does RAID 5 protect against corruption? I know that RAID is not a backup solution. I am trying to figure out how to make sure that I am not backing up corrupt data!

    Read the article

  • How to view status of software RAID 1 resynching?

    - by tputkonen
    I have two 500 GB disks and yesterday I mirrored first drive to the second one using software RAID 1. PC has now been on for 30 hours. Both disks say "Resynching", but there is no progress indicator. In addition, there is a small yellow exclamation mark on both disks. My questions are: How long could the synch take for 500 GB drive with about 150 GB of data? PC has 4 GBs of RAM and AMD dual core 4000+ Is there a way to monitor status of the synching? How can I check what the exclamation mark means?

    Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >