Search Results

Search found 1299 results on 52 pages for 'peopletools 8 51'.

Page 20/52 | < Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >

• Dedicated server not responding. Malicious?

  - by user2801881

  My Dedicated server dies for days on end. As soon as i reboot after about 20 seconds it does again. Then it will just work again and be fine for another week or so. Im convinced its malicious. Not sure what results or readings i can give you so just ask and i will do whatever is needed. netstat (top 20 connections) 7 79.142.88.250 8 120.202.249.19 8 159.226.21.62 8 188.168.38.102 8 202.114.6.37 8 222.62.207.70 9 60.191.35.42 10 112.124.46.186 10 116.228.55.184 10 181.133.218.11 10 222.90.111.146 11 183.136.146.110 12 124.127.51.135 12 92.225.24.24 13 221.176.23.242 15 119.10.115.165 16 17 218.6.224.66 21 116.228.55.217 24 114.112.194.19 top CPU usage seems to add up to about 10% Mailq is empty Thanks in advance

  Read the article

• RAID1 rebuild fails due to disk errors

  - by overlord_tm

  Quick info: Dell R410 with 2x500GB drives in RAID1 on H700 Adapter Recently one of drives in RAID1 array on server failed, lets call it Drive 0. RAID controller marked it as fault and put it offline. I replaced faulty disk with new one (same series and manufacturer, just bigger) and configured new disk as hot spare. Rebuild from Drive1 started immediately and after 1.5 hour I got message that Drive 1 failed. Server was unresponsive (kernel panic) and required reboot. Given that half hour before this error rebuild was at about 40%, I estimated that new drive is not in sync yet and tried to reboot just with Drive 1. RAID controller complained a bit about missing RAID arrays, but it found foreign RAID array on Drive 1 and I imported it. Server booted and it runs (from degraded RAID). Here is SMART data for disks. Drive 0 (the one that failed first) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 142 142 021 - 3866 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10432 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 112 106 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 198 000 - 3 And Drive 1 (the drive which was reported healthy from controller until rebuild was attempted) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 35 3 Spin_Up_Time POS--K 143 143 021 - 3841 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10455 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 114 105 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 3 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 In extended error logs from SMART I found: Drive 0 has only one error Error 1 [0] occurred at disk power-on lifetime: 10282 hours (428 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 18 00 00 00 6a 24 20 40 00 Error: IDNF at LBA = 0x006a2420 = 6956064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 60 00 f8 00 00 00 6a 24 20 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 18 00 60 00 00 00 6a 24 00 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 80 00 58 00 00 00 6a 23 80 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 68 00 50 00 00 00 6a 23 18 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 10 00 10 00 00 00 6a 23 00 40 00 17d+20:25:18.104 WRITE FPDMA QUEUED But Drive 1 has 883 errors. I see only few last ones and all errors I can see look like this: Error 883 [18] occurred at disk power-on lifetime: 10454 hours (435 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 80 00 00 39 97 19 c2 40 00 Error: AMNF at LBA = 0x399719c2 = 966203842 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:57.802 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:57.779 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:55.704 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:55.681 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:53.606 READ FPDMA QUEUED Given those errors, is there any way I can rebuild RAID back, or should I make backup, shutdown server, replace disks with new ones and restore it? What about if I dd faulty disk to new one from linux running on USB/CD? Also, if anyone have more experiences, what could be causes for those errors? Crappy controller or disks? Disks are about 1 year old, but it is pretty unbelievable to me that both would die within so short timespan.

  Read the article

• Windows Server 2012 VPN Server on AWS VPC EC2 Instance

  - by abran

  I'd like to use window server 2012 VPN on a AWS VPC EC2 instance. The VPC has one public subnet and the EC2 instance has one network adapter. I've taken the following steps, but have been unsuccessful; am I missing a step or configuration? Thanks. Configured an elastic IP for the VPC Enabled protocols 47, 50, & 51 Added the RRAS role to the (EC2 instance) server Configured the RRAS for vpn only. Note: I'm able to RDP to the EC2 instance, but not able to ping the external IP.

  Read the article

• Check_webinject plugin will not connect to https site using

  - by uSlackr

  We're using Nagios to monitor some of our web sites. We have a script that uses the older plugin that we are trying to switch to using webinject.pl from cpan. When the script runs, it generates this error: LWP::Protocol::https::Socket: SSL connect attempt failed with unknown error error:1407741A:SSL routines:SSL23_GET_SERVER_HELLO:tlsv1 alert decode error at /usr/local/share/perl5/LWP/Protocol/http.pm line 51. It appears the web site does not support TLSv1 for https. If it matters, the site is a Cisco WebVPN. I've pointed the same script at a different site that does support TLSv1 and it seems to work fine. My web search is coming up empty. Successful connect: <case id="1" description1="Metro Home Page" description2="Metro, login test" method="get" url="https://metro.myco.com/index.php" verifypositive="restricted" logrequest="yes" logresponse="yes" sleep="1" / Failing connect: <case id="2" description1="WebVPN Home Page" description2="webvpn.myco.com login test" method="get" url="https://webvpn.myco.com/webvpn.html" verifypositive="Authorized" logrequest="yes" logresponse="yes" sleep="1" /

  Read the article

• eMail with Conflicting Headers not blocked in MS365

  - by John Meredith Langstaff

  On occasion, a company receives eMail with two header fields (“Received” and “From”) containing data that contradict each other drastically. Should they not expect their anti-spam system to flag or block items with contradictions in these fields? For example, they received an eMail which contained [almost exactly] these two headers: Received: from [107.52.51.26] by web315204.mail.ne1.yahoo.com via HTTP; Mon,28 Oct 2013 04:28:04 PDT From: Barry Smith [email protected] Obviously, eMail from an @att.net address isn’t coming from a server on the domain yahoo.com, and Yahoo isn’t forwarding AT&T’s eMail. There were no other headers indicating that the item was sent “OnBehalfOf”, or “Forwarded-by”, or “By_Proxy” or any other such. Should I write a utility to scan incoming eMail for such conflicts, or look more closely at their spam filtering to block this kind of eMail? Their eMail system is Hosted Exchange on MS-365. My central question is, where specifically do I look in MS-365 to get this type of conflicted eMail blocked?

  Read the article

• Gathering IP's from a complicated log

  - by Harry

  I have a question regarding the use of some more advanced grep, awk, sed. I have a log file, for a proprietary MTA, that contains IP's in a string, delimited by [redacted]^~x.x.x.x^[redacted]. So far all of my grepping, awking, and sedding hasn't gotten me very far. This log file has 331520 lines in it. My goal was to simply grep out the ip's, then do a for loop with sed, to sed 's/$i/redacted'. I'm including a sample of one of the log entries. If you all have any idea, I would be greatly appreciative. Jun 4 15:21:52 host.name mta-name: 13388^~88/CC-04671-FCA0DCF4^~D^~<redactedmessageid>^~@^[email protected]^~redacted.hostname^~000.00.000.000^~port^~esmtp^~^~external_routing_nobounce^~0^~0.51^~subjectofmessage^~250 2.6.0 <redactedmessageid> [InternalId=2178458] Queued mail for delivery

  Read the article

• Foward slash in kibana 3 query

  - by G Mawr

  I'm trying to add a query that will match a request that ends with a slash, like this one: n.n.n.n - - [16/Oct/2013:16:40:41 +0100] "GET / HTTP/1.1" 200 25058 "-" "Mozilla/5.0 (iPad; CPU OS 7_0_2 like Mac OS X) AppleWebKit/537.51.1 (KHTML, like Gecko) Version/7.0 Mobile/11A501 Safari/9537.53" I'm using the Lucene query type. If my query is set to *, I see the event. If I set it to request:"css", I see CSS requests, as expected. However, all of the following yield no results: request:"/" request:"\/" request:"\\/" I tried a Lucene regular expression, with no luck: request:/\// I note that someone else is getting what appears to be a similar issue, although that's on Kibana 2: https://github.com/rashidkpc/Kibana/issues/401 How can I query for requests that end with a / character?

  Read the article

• how to pipe data to sftp connection?

  - by JMW

  ftp supports the put "|..." "remote-file.name" command to pipe data to an ftp connection. Is there something similar available for sftp? In sftp i get the following error: sftp 'jmw@backupsrv:/uploads' sftp> put "| tar -cx /storage" "backup-2012-06-19--17-51.tgz" stat | tar -cv /storage: No such file or directory as above the sftp client doesn't obviously execute the command. i want to use the pipe command to directly redirect the file stream to sftp. (because there is not enough space left to create a backup file on the same disk before uploading it to sftp server.)

  Read the article

• Ip doesn't change when switching networks, although automatic ip is set. Cause of the issue known

  - by Julio Acevedo

  I have two routers at my house. Both of them have DCHP server enabled. One of them is 192.168.1.1 and gives adresses from 192.168.1.2 to 192.168.1.32 The other one is 192.168.1.50 and gives adresses from 192.168.1.51 to 192.168.1.99 The problem is that I only have internet access in one because my ip is 192.168.1.7, and when I switch to the other one, the ip remains 192.168.1.7, even though I have automatically get a ip adress in Ipv4. When I manually change my ip to one in the range allowed by the router, I can browse the internet. Any ideas how to solve this? Thank you.

  Read the article

• Convert audio file to FLAC with ffmpeg?

  - by elpsk

  can I convert one of this format to compatible 16000.0 Sample Rate FLAC file? kAudioFormatLinearPCM = 'lpcm', kAudioFormatAppleIMA4 = 'ima4', kAudioFormatMPEG4AAC = 'aac ', kAudioFormatMACE3 = 'MAC3', kAudioFormatMACE6 = 'MAC6', kAudioFormatULaw = 'ulaw', kAudioFormatALaw = 'alaw', kAudioFormatMPEGLayer1 = '.mp1', kAudioFormatMPEGLayer2 = '.mp2', kAudioFormatMPEGLayer3 = '.mp3', kAudioFormatAppleLossless = 'alac' I tried using ffmpeg ffmpeg -i audio.xxx -acodec flac audio.flac but result is FFmpeg version CVS, Copyright (c) 2000-2004 Fabrice Bellard Mac OSX universal build for ffmpegX configuration: --enable-memalign-hack --enable-mp3lame --enable-gpl --disable-vhook --disable-ffplay --disable-ffserver --enable-a52 --enable-xvid --enable-faac --enable-faad --enable-amr_nb --enable-amr_wb --enable-pthreads --enable-x264 libavutil version: 49.0.0 libavcodec version: 51.9.0 libavformat version: 50.4.0 built on Apr 15 2006 04:58:19, gcc: 4.0.1 (Apple Computer, Inc. build 5250) Input #0, wsaud, from 'audio.alac': Duration: 00:00:03.8, start: 0.000000, bitrate: 199 kb/s Stream #0.0: Audio: adpcm_ima_ws, 24931 Hz, stereo, 199 kb/s Unable for find a suitable output format for 'audio.flac' I also installed flac codec for mac, but nothing... I tried also use convtoflac.sh (from http://legroom.net/software/convtoflac) but result is similar. Any idea to convert in flac?

  Read the article

• Virtual machine on ubuntu

  - by MITHIYA MOIZ

  I have configured virtual machine on ubuntu with the help of below article, https://help.ubuntu.com/9.04/serverguide/C/libvirt.html I managed to finish all the part except the major portion getting virtual host to talk to real network, Which I guess should be done only via bridge interface. Via virtual machine manager I try to choose any interface it gives me interface not bridged When I try to bridge the interceface eth0 as below auto br0 iface br0 inet static address 192.168.0.223 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off I cannot communicate with this interface to network, host server looses all the communication to network. But when I remote bridge interface from /etc/network/interfaces And configure eth0 as below it works fine The primary network interface auto eth0 iface eth0 inet static address 192.168.0.223 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 dns-nameservers 62.215.6.51 gateway 192.168.0.1 how can i setup bridge interface correctly and how would my /etc/netwrok/interfaces file would look a like.

  Read the article

• TIME column in TOP command for mysql

  - by michael

  When I run top on my database server I get that mysqld has been running for 4:00.51 and it continues to go up. I assume this means that one process with mysql has been running this long from other posts on here. Its not set to cumulative mode as best I can tell as the heading looks like it would change to CTIME if that be the case. What I'm wondering is if this is normal for a site that makes a lot of individual connections using PHP. I shouldn't have any long running processes that would hold on to a mysql connection for this long, only seconds at most. Am I incorrect to assume that this time relates to one connection/process running? I think usually I see it flash up and away on the TOP, not just stay there with this number increasing.

  Read the article

• System Center Configuration Manager 2007 - Debugging Client Installs

  - by Dayton Brown

  Hi All: Having an issue installing the CCMsetup client on desktops. The CCMSetup makes it to the PC, files are there, it gets added to the services for automatic start, it starts, but quits almost instantly. Logs on the desktop show a entry like this. <![LOG[Failed to successfully complete HTTP request. (StatusCode at WinHttpQueryHeaders: 404)]LOG]!><time="14:28:51.183+240" date="06-11-2009" component="ccmsetup" context="" type="3" thread="2388" file="ccmsetup.cpp:5808"> What am I missing? EDIT: Firewall is off on both client and server.

  Read the article

• need to run command against multiple lines in file that start with ica-tcp

  - by Nick Parsells

  I want to run a command on each line of a file I have, however its a bit more complicated then I originally thought. The file contents look like this typically; however there are sometimes more connections: SESSIONNAME USERNAME ID STATE TYPE DEVICE services 0 Disc console 1 Conn t-rpal 48 Disc ica-tcp#0 bpofiretest 50 Active wdica rdp-tcp#2 a-nparsells 51 Active rdpwd ica-tcp 65536 Listen rdp-tcp 65537 Listen The command I want to run is reset session ica-tcp#0. I also want to run the same command on any additional connections that start with ica-tcp that the scripts finds in the file. How can I write a script like that in powershell? thanks!

  Read the article

• How can I enable anonymous access to a Samba share under ADS security mode?

  - by hemp

  I'm trying to enable anonymous access to a single service in my Samba config. Authorized user access is working perfectly, but when I attempt a no-password connection, I get this message: Anonymous login successful Domain=[...] OS=[Unix] Server=[Samba 3.3.8-0.51.el5] tree connect failed: NT_STATUS_LOGON_FAILURE The message log shows this error: ... smbd[21262]: [2010/05/24 21:26:39, 0] smbd/service.c:make_connection_snum(1004) ... smbd[21262]: Can't become connected user! The smb.conf is configured thusly: [global] security = ads obey pam restrictions = Yes winbind enum users = Yes winbind enum groups = Yes winbind use default domain = true valid users = "@domain admins", "@domain users" guest account = nobody map to guest = Bad User [evilshare] path = /evil/share guest ok = yes read only = No browseable = No Given that I have 'map to guest = Bad User' and 'guest ok' specified, I don't understand why it is trying to "become connected user". Should it not be trying to "become guest user"?

  Read the article

• command prompt DIR with wildcard returns unexpected results

  - by Don Dickinson

  I am running 2003 server (latest service pack). When i type this on the command line: dir 2010* or dir 2010*.* i receive this as the result: 02/01/2011 02:34 PM 2,460 2011-02-01-14-34-23-807.mdn 02/02/2011 08:59 AM 3,757 2011-02-02-08-59-32-604.req 02/01/2011 09:16 AM 235 2011-02-01-09-16-35-104.dat 02/02/2011 05:06 PM 460 2011-02-02-17-06-05-166.log 02/01/2011 03:31 PM 66,570 2011-02-01-15-31-27-838.dat 02/01/2011 03:16 PM 145 2011-02-01-15-16-51-135.log 02/01/2011 08:52 PM 1,608,916 2011-02-01-20-52-57-416.req 7 File(s) 1,682,543 bytes 0 Dir(s) 42,891,452,416 bytes free can anyone tell me why? i was expecting to see a list of only files that begin with "2010". there are no such files in the directory, so i wasn't expecting to see anything. i must either misunderstand how DIR handles wildcards or i'm doing something stupid.

  Read the article

• How to dispose of old rack-mount servers?

  - by Nic

  I have two old rack-mount servers lying around that I want to get rid of. One is a HP DL380 G2, the other is an IBM from the same era. Both machines boot up, but I don't have any harddrives for them, or any use for them. Worse yet, both machines appear to have been dropped at some point and the rail kits are bent out of shape and can't be removed, making them unusuable in a rack environment. I'd like to recycle them or dispose of them in some kind of safe manner, but don't really know what my options are. I'm in western Canada. Any suggestions? Update: If you found this question interesting, please consider visiting StackExchange Area 51 to support the proposal for a dedicated Recycling Q&A site.

  Read the article

• slow DNS resolution

  - by Ehsan

  I have a DNS server that resolves all queries for an internal group of servers. It is a bind on CentOS 5.5 (same as RHEL5) and I have set it up to allow recursion and resolve direction without any forwarders. The problem I am facing is that it takes a freakishly long amount of time to resolve a name for the first time. (in the magnitudes of 20 sec) This causes clients to give timeout. When I set it to forward all to Google's public DNS, i.e. 8.8.8.8+8.8.4.4, it works very nicely (within a second). I tried monitoring the traffic on the net to see why it is doing this: [root@ns1 ~]# tcpdump -nnvvvA -s0 udp tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 23:06:36.137797 IP (tos 0x0, ttl 64, id 35903, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<[email protected]... .....N.5.(6.M=...........www.paypal.com..... 23:06:36.140594 IP (tos 0x0, ttl 64, id 56477, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.6128 > 192.35.51.30.53: [udp sum ok] 10105 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@........#3....5.3fR'y...........www.paypal.com.......)........ 23:06:38.149756 IP (tos 0x0, ttl 64, id 13078, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.52425 > 192.54.112.30.53: [udp sum ok] 54892 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) [email protected]&.....6p....5.3.q.l...........www.paypal.com.......)........ 23:06:40.159725 IP (tos 0x0, ttl 64, id 43016, offset 0, flags [none], proto: UDP (17), length: 71) 172.17.1.4.24059 > 192.42.93.30.53: [udp sum ok] 11205 [1au] A? www.paypal.com. ar: . OPT UDPsize=4096 (43) E..G....@..@.....*].]..5.3..+............www.paypal.com.......)........ 23:06:41.141403 IP (tos 0x0, ttl 64, id 35904, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.10.36942 > 172.17.1.4.53: [udp sum ok] 19773+ A? www.paypal.com. (32) E..<.@..@..@... .....N.5.(6.M=...........www.paypal.com..... 23:06:42.169652 IP (tos 0x0, ttl 64, id 44001, offset 0, flags [none], proto: UDP (17), length: 60) 172.17.1.4.9141 > 192.55.83.30.53: [udp sum ok] 1184 A? www.paypal.com. (32) E..<[email protected].#..5.(...............www.paypal.com..... 23:06:42.207295 IP (tos 0x0, ttl 54, id 38004, offset 0, flags [none], proto: UDP (17), length: 205) 192.55.83.30.53 > 172.17.1.4.9141: [udp sum ok] 1184- q: A? www.paypal.com. 0/3/3 ns: paypal.com. NS ns1.isc-sns.net., paypal.com. NS ns2.isc-sns.com., paypal.com. NS ns3.isc-sns.info. ar: ns1.isc-sns.net. AAAA 2001:470:1a::1, ns1.isc-sns.net. A 72.52.71.1, ns2.isc-sns.com. A 38.103.2.1 (177) E....t..6./A.7S......5#..................www.paypal.com..................ns1.isc-sns.net..............ns2.isc-sns...............ns3.isc-sns.info..,.......... ..p.............,..........H4G..I..........&g.. (this goes on for a few more seconds) If you look carefully, you will see that the first 3-4 root servers did not respond at all. This wastes 7-8 seconds, until one of them responded. Do you think I have setup something wrong here? Interestingly, when I dig directly from the root servers that did not respond, the always respond very fast (showing the firewall/nat is not the issue here). E.g. dig www.paypal.com @192.35.51.30 works perfectly, consistently, and very fast. What do you think about this mystery?

  Read the article

• TIME_WAIT in netstat of Apache processes

  - by Howard

  What are the meaning of the TIME_WAIT when using netstat of my web server process? I am sure the web server is not over loaded. tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 15655/apache2 tcp 0 0 x.x.x.x:80 123.125.66.35:19667 SYN_RECV - tcp 0 0 x.x.x.x:80 113.138.59.140:12186 TIME_WAIT - tcp 0 0 x.x.x.x:80 66.249.67.121:59493 ESTABLISHED 23702/apache2 tcp 0 0 x.x.x.x:80 69.28.51.206:40652 TIME_WAIT - tcp 0 0 x.x.x.x:80 221.126.149.99:51877 TIME_WAIT - tcp 0 0 x.x.x.x:80 221.126.149.99:51872 TIME_WAIT - tcp 0 0 x.x.x.x:80 123.125.66.19:13084 TIME_WAIT -

  Read the article

• ffmpeg encoding on QuadCore

  - by Gotys

  I am trying to push my server's CPU cores to the max, but no success. Encoding 2-pass style, set my "-threads" to 128 . When running 2nd pass , the CPU seems to be at 98% usage, but first pass run totally ignores "-threads" option. Using libx264 . Here is my preset: flags=+loop+mv4 cmp=256 partitions=+parti4x4+parti8x8+partp4x4+partp8x8+partb8x8 me_method=hex subq=7 trellis=1 refs=5 bf=3 flags2=+bpyramid+wpred+mixed_refs+dct8x8 coder=1 me_range=16 g=250 keyint_min=25 sc_threshold=40 i_qfactor=0.71 qmin=10 qmax=51 qdiff=4 Is there any reason why the 1st pass is not utilizing my CPUs ? Thank you in advance! This community has always been very kind to me.

  Read the article

• ffmpeg encoding on QuadCore

  - by Gotys

  I am trying to push my server's CPU cores to the max, but no success. Encoding 2-pass style, set my "-threads" to 128 . When running 2nd pass , the CPU seems to be at 98% usage, but first pass run totally ignores "-threads" option. Using libx264 . Here is my preset: flags=+loop+mv4 cmp=256 partitions=+parti4x4+parti8x8+partp4x4+partp8x8+partb8x8 me_method=hex subq=7 trellis=1 refs=5 bf=3 flags2=+bpyramid+wpred+mixed_refs+dct8x8 coder=1 me_range=16 g=250 keyint_min=25 sc_threshold=40 i_qfactor=0.71 qmin=10 qmax=51 qdiff=4 Is there any reason why the 1st pass is not utilizing my CPUs ? Thank you in advance! This community has always been very kind to me.

  Read the article

• Problem connecting to MySQL with zend

  - by wheresrhys

  I've set up a virtual host on my local machine (windows xp with xampp installed), have installed zend there and am now trying to connect to the MySQLdatabase. I get the following error message: Message: SQLSTATE[HY000] [2003] Can't connect to MySQL server on ''myhost.com'' (10060) All the tips I've found via google haven't helped. I use kaspersky antivirus and have added port 3306 to the allowed list for MySQL and Apache. I've also pinged myhost.com:3306 and get a response (with ip address 67.63.50.51), though localhost:3306 and 127.0.0.1:3306 aren't found. I've checked that other apps can still access MySQL if the virtual host is pointed at them instead and my non zend apps do work. I guess I have to do something further to the port, or maybe force the app to use a different port, but am not sure how to do either. Any help appreciated.

  Read the article

• Find largest value of integer in repeating string

  - by dotancohen

  I have a script log file that looks a bit like this: 2012-9-16 Did something Did 345 things Script time: 244 seconds 2012-9-17 Did yet something Did another thing 23 times Script time: 352 seconds 2012-9-18 Did something special for 34 seconds 51 times Did nothing at all Script time: 122 seconds I would like to find the largest value of N in the lines Script time: N seconds. However, I need to keep the context, so simply removing all lines that don't contain Script time in them is not a viable solution. Currently, I am grepping for lines with Script time, then sorting those to find the highest value, then going back to the original file and searching for that value. However, if there is a more straightforward way then I would love to know. This is on Vim 7.3 on a recent CentOS. I would prefer to remain in VIM if possible. Thanks.

  Read the article

• MySQL dump, output each table row on a new line whilst using --extended-insert

  - by soopadoubled

  I'm having an issue, where for ease of use, I'd like to be able to format a command line MySQL dump so that each row of a given table is on a new line when using the --extended-insert option. Usually when using --extended-insert, every row of a given table is outputted on one line, and as far as I am aware there's no way to change this, other than post-processing the dump with perl or such like. The format I'm looking for is: -- -- Dumping data for table `ww_tbCountry` -- INSERT INTO `ww_tbCountry` (`iCountryId_PK`, `vCountryName`, `vShortName`, `iSortFlag`, `fTax`, `vCountryCode`, `vSageTaxCode`) VALUES (22, 'Albania', 'AL', 1, 0.00, '8', 'T9'), (33, 'Austria', 'AT', 1, 15.00, '40', 'T9'), (40, 'Belarus', 'BY', 1, 0.00, '112', 'T9'), (41, 'Belgium', 'BE', 1, 15.00, '56', 'T9'), (51, 'Bulgaria', 'BG', 1, 15.00, '100', 'T9' However, when I dump a database using Phpmyadmin, using --extended-insert, each row is dumped on a new line (as shown by the example above). I've gone through Phpmyadmin and can't find any documentation that would explain this. Is anyone able to shed any light on this? Thanks in advance, Ian

  Read the article

• Screen Casting using ffmpeg (too fast)

  - by rowman

  I can use ffmpeg to make screen casts: ffmpeg -f x11grab -s 1280x800 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv However the output comes out to be too fast paced. It also happens with GTK RecordMyDesktop if I enable the encode on the fly. So, the questions is how to get a normal video pace. Also in order to capture the sound with ffmpeg what option should be used? FFmpeg Output: ffmpeg -f x11grab -s 1280x800 -r 30 -i :0.0 -c:v libx264 -framerate 30 -r 30 -crf 18 out.mkv ffmpeg version N-35162-g87244c8 Copyright (c) 2000-2012 the FFmpeg developers built on Oct 7 2012 15:56:19 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 51. 73.102 / 51. 73.102 libavcodec 54. 64.100 / 54. 64.100 libavformat 54. 29.105 / 54. 29.105 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 19.102 / 3. 19.102 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 16.100 / 0. 16.100 libpostproc 52. 1.100 / 52. 1.100 [x11grab @ 0xab896a0] device: :0.0 -> display: :0.0 x: 0 y: 0 width: 1280 height: 800 [x11grab @ 0xab896a0] shared memory extension found [x11grab @ 0xab896a0] Estimating duration from bitrate, this may be inaccurate Input #0, x11grab, from ':0.0': Duration: N/A, start: 1350136942.608988, bitrate: 983040 kb/s Stream #0:0: Video: rawvideo (BGR[0] / 0x524742), bgr0, 1280x800, 983040 kb/s, 30 tbr, 1000k tbn, 30 tbc [libx264 @ 0xab87320] using cpu capabilities: MMX2 SSE2Fast SSSE3 Cache64 SlowCTZ SlowAtom [libx264 @ 0xab87320] profile High 4:4:4 Predictive, level 3.2, 4:4:4 8-bit [libx264 @ 0xab87320] 264 - core 128 r2 198a7ea - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=4 threads=6 lookahead_threads=1 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=18.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, matroska, to 'out.mkv': Metadata: encoder : Lavf54.29.105 Stream #0:0: Video: h264, yuv444p, 1280x800, q=-1--1, 1k tbn, 30 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> libx264) Press [q] to stop, [?] for help frame= 10 fps=0.0 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 19 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 28 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 37 fps= 17 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 45 fps= 16 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 47 fps= 14 q=0.0 size= 1kB time=00:00:00.00 bitrate= 0.0kbits/sframe= 52 fps= 13 q=24.0 size= 257kB time=00:00:00.00 bitrate=2101632.0kbiframe= 55 fps= 12 q=24.0 size= 257kB time=00:00:00.10 bitrate=20808.2kbitsframe= 59 fps= 11 q=24.0 size= 289kB time=00:00:00.23 bitrate=10145.0kbitsframe= 64 fps= 11 q=24.0 size= 289kB time=00:00:00.40 bitrate=5894.7kbits/frame= 70 fps= 11 q=24.0 size= 289kB time=00:00:00.60 bitrate=3933.1kbits/frame= 72 fps= 10 q=24.0 size= 289kB time=00:00:00.66 bitrate=3549.2kbits/frame= 77 fps=9.8 q=24.0 size= 289kB time=00:00:00.83 bitrate=2837.7kbits/frame= 80 fps=9.6 q=24.0 size= 289kB time=00:00:00.93 bitrate=2533.5kbits/frame= 85 fps=9.3 q=24.0 size= 289kB time=00:00:01.10 bitrate=2146.9kbits/frame= 89 fps=9.3 q=24.0 size= 289kB time=00:00:01.23 bitrate=1917.1kbits/frame= 92 fps=9.1 q=24.0 size= 289kB time=00:00:01.33 bitrate=1773.3kbits/frame= 96 fps=9.0 q=24.0 size= 289kB time=00:00:01.46 bitrate=1612.4kbits/frame= 99 fps=8.8 q=24.0 size= 321kB time=00:00:01.56 bitrate=1676.8kbits/frame= 104 fps=8.7 q=24.0 size= 321kB time=00:00:01.73 bitrate=1515.2kbits/frame= 109 fps=5.3 q=24.0 Lsize= 1093kB time=00:00:03.56 bitrate=2511.5kbits/s video:1092kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.120198% [libx264 @ 0xab87320] frame I:3 Avg QP:18.93 size:142610 [libx264 @ 0xab87320] frame P:43 Avg QP:20.79 size: 15751 [libx264 @ 0xab87320] frame B:63 Avg QP:23.75 size: 195 [libx264 @ 0xab87320] consecutive B-frames: 21.1% 1.8% 11.0% 66.1% [libx264 @ 0xab87320] mb I I16..4: 50.0% 21.1% 28.9% [libx264 @ 0xab87320] mb P I16..4: 6.1% 0.9% 3.2% P16..4: 5.5% 1.2% 0.6% 0.0% 0.0% skip:82.5% [libx264 @ 0xab87320] mb B I16..4: 0.4% 0.1% 0.0% B16..8: 2.9% 0.1% 0.0% direct: 0.0% skip:96.5% L0:40.7% L1:57.0% BI: 2.3% [libx264 @ 0xab87320] 8x8 transform intra:14.5% inter:46.1% [libx264 @ 0xab87320] coded y,u,v intra: 33.5% 24.1% 25.4% inter: 0.9% 0.4% 0.4% [libx264 @ 0xab87320] i16 v,h,dc,p: 70% 26% 1% 3% [libx264 @ 0xab87320] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 11% 21% 30% 5% 7% 5% 7% 4% 10% [libx264 @ 0xab87320] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 32% 35% 12% 2% 4% 3% 4% 3% 5% [libx264 @ 0xab87320] Weighted P-Frames: Y:0.0% UV:0.0% [libx264 @ 0xab87320] ref P L0: 57.0% 5.6% 26.8% 10.6% [libx264 @ 0xab87320] ref B L0: 69.4% 22.6% 8.0% [libx264 @ 0xab87320] ref B L1: 93.7% 6.3% [libx264 @ 0xab87320] kb/s:2460.40

  Read the article

< Previous Page | 16 17 18 19 20 21 22 23 24 25 26 27  | Next Page >