Search Results

Search found 7124 results on 285 pages for 'printer driver'.

Page 203/285 | < Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >

  • Acer Aspire ASE700-UQ660A will not respond to power button

    - by Tim R.
    This is something of a continuation of this question. I am now completely unable to boot this computer. The last time I used it, I used hibernation mode. When I needed to use it again, it would not respond at all to the power button, keyboard, or mouse. I tried: Holding down the power button for 15 seconds pressing the power button Unplugging the power cord for 30 seconds, plugging it back in, and trying again Removing the motherboard battery for over a minute and reinstalling it Before removing the motherboard battery, none of the lights on the front of the computer lit up. After reinstalling the battery and plugging the power cord back in, the light behind the power button is constantly illuminated (without even pressing the power button), but there is still no response to the power button, no fans turned on, nothing else that would indicate that it is running. System: Acer Aspire ASE700-UQ660A (Specs should be all factory defaults except:) 4 GB RAM Nvidia GeForce 8600 GT with driver version 197.45 Windows 7 Professional 64 bit

    Read the article

  • Windows lowers volume because of "communication"

    - by SnippetSpace
    Randomly, or at system sound (usb connect for example) Windows 8 lowers the volume of all other sources. (Same problem can exist on windows 7, just look online). This is happening because of the "communication detection" made to detect phone calls and then lower volume. But in my case it happens all the time without reason as if windows always considers myself in a call. Do any of you have the same problem? is this a driver issue or a windows issue? I know this has been posted many times but they usually just tell you to turn off the setting above. I'm looking for an explanation or a solution :). Thanks for your feedback and ideas.

    Read the article

  • DIY NAS - links for Instructions

    - by Kaushik Gopal
    Good folk of SU, I'm planning to build a NAS (Network Access Storage). I'm planning to do it cheap (:read Old PC Config + Open source software). I was looking for good DIY links . Before you shoot this down as a Repost, I'm only looking for good links containing detailed instructions for setting up a NAS. I did a fair bit of searching and found these links (so please suggest others. While these links are great they delve more on the hardware side, i'm looking for more instructions in the software side). For the sake of the interwebs: Ubuntu: http://snarfquest.com/wiki/index.php/Setting_up_a_Home_NAS http://www.smallnetbuilder.com/content/view/27962/77/ http://jonpeck.blogspot.com/2006/11/how-to-configure-80-fileserver-in-45.html FreeNAS http://www.smallbusinesscomputing.com/webmaster/article.php/3719706 http://www.codeproject.com/KB/system/homemade_nas.aspxhttp://www.codeproject.com/KB/system/homemade_nas.aspx There was one at rubbervir.us that everyone points to, but apparently the site has gone down. A couple of other queries: Is Printer/Scanner sharing a possibility with NAS devices? Many talk of torrent support with NAS Devices, a little more light on this? Does this mean, an auto download of torrent through a feed into NAS, or just support for storing Torrent download files onto the NAS(don't see the difference between the latter and a normal file tranfer)

    Read the article

  • Windows 7 MSDN version

    - by Larry Branham
    I recently purchased a copy of Windows 7 online. Upon trying to install, it stopped and I was told that it could not find a 64 bit driver for my CD/DVD and I could not finish install. I contacted Microsoft and was told that this was something called an MSDN version according to the product key and that was the reason for the problem. They also said is was illegal to sell it to me. The company I bought it from never returned my calls or emails and luckily I got money back through Amazon. Amazon didn't even want me to send it back. Anyway my question is, is there anyway to load this onto my system and will I have problems or should I just throw it out? Any help would be great. Thanks

    Read the article

  • Scanner Installation: Epson Perfection 3170 Photo, Windows 7 & Adobe Acrobat

    - by Galaxy5727
    I installed the Driver v3.04A from Epson's Web site -- epson12180.exe that is supposedly for Windows 7. Now, the scanner works by itself, i.e. if I hit the scan button I get a dialog menu and can scan with one of the options there but not with Adobe Acrobat. What I need is to have it working from Adobe Acrobat when I go File - Create PDF - From Scanner - Custom Scan... The current state is that I see Scanner: "Please select a device" and no other available devices. I remember I used to see at least 2 other like "WIA Epson Perfection" and smth like "Epson Perfection". "WIA Epson Perfection" is the option that I am hoping to see to move on. Scanner: Epson Perfection 3170 Photo System: Windows 7, 64-bit Software: Adobe Acrobat 9 Pro

    Read the article

  • Packet loss with Broadcom wireless and Ubuntu

    - by stevemegson
    I have a machine with Ubuntu 9.04 and a Broadcom BCM4306 wireless card which has been running quite happily for many months with the b43legacy driver that's suggested by Hardware Drivers. Suddenly, I'm now seeing crippling packet loss, varying between 30% and 90% when pinging the router. My WinXP machine is still quite happy even when sat next to the Ubuntu box, so I assume that it's not some new source of interference. What else is likely to have changed? How should I go about diagnosing and fixing this?

    Read the article

  • Linux Ubuntu: Updating the GRUB menu

    - by Mr X
    So apparently there are 2 versions of Linux on my laptop(I have a dual boot system with Linux and Windows 8 but Linux is the master OS). One of them uses the Kernel version 3.11.0 whose headers + source code are incompatible with my wireless driver. My laptop is a Toshiba Satellite with a Realtek RTL8188CE wireless lan.So the newer kernel version is still the first option on the menu and to get to Linux I use the "Previous versions of linux" which is running Kernel version 3.2.0-55. What can I do to update the grub menu so that Linux version with the 3.2.0-55 Kernel appears as the primary option? Do I need to get rid of/uninstall the newer kernel version? How can I do this without screwing up Linux entirely?

    Read the article

  • GeForce 9600GT support for dual monitor setup

    - by Theo
    I have a NVIDIA GeForce 9600 GT (point of view, link) on an Asus M2V-MX motherboard. The card has one DVI, HDMI and S-Video output. The graphics card does not seem to support dual monitors: the driver control panel for the graphics card does not detect a second monitor that is attached via S-Video (which leads me to believe that it doesn't support dual monitors with DVI and the other connections). Would it be possible to use a VGA/DVI splitter to attach two monitors to the single DVI output on the graphics card? Would this allow for a dual monitor setup, or only mirroring? How do I know if the graphic card supports this? With this particular motherboard, would it be possible to use the onboard video for another monitor?

    Read the article

  • Lenovo DVD Drive Disabled After Windows 7 Install

    - by David Lacher
    Upgraded hard drive in Lenovo T61P; decided to start fresh with Windows 7 Pro. Windows installed, so DVD drive was working. All of a sudden, driver is not recognized. Device is "HL-DT-ST DVDRAM GSA-U10N ATA Device". It appears on device manager but with the yellow tag; have tried uninstalling, searching for drivers, everything I can think of. Cannot even start over with Windows 7 installation disk because disk spins but then stops and My Computer does not recognize the drive. Help please. thank you. David Lacher

    Read the article

  • Can't get Intel drivers for ASUS P6T Deluxe

    - by Alex K
    Hi everybody, A few days back my Win7 Ultimate started bugging me to install the RAID drivers for my ASUS P6T Delux. Fine, I'm all for having up to date drivers even for stuff I don't use. The problem is that the drivers I download from both ASUS support site here and the ones I get directly from Intel (can't post the second link, since I have less than 10 rep, but it's the first hit for "Intel(R) Matrix Storage Manager Driver" on google) say that my system does not meet the minimum system requirements. Impossible, I would think, what with it having the X58 chipset and the Windows version is supported one. Has anyone encountered something like this before? Any clues on how to solve this would be much appreciated. Thanks!

    Read the article

  • NIC models for HVM guests in Xen 4.0

    - by Jed Daniels
    Is there a list of NIC models that I should use with various HVM guests in Xen 4.0? Is there even a list of possible choices for the model=field? I'm planning on running both Windows and FreeBSD guests on the particular Xen box that I'm configuring now, and ideally I'd like a setting that can work on both of them and get me gigabit speeds without a lot of extra hassle loading special drivers (similar to VMware's e1000 NIC option). Any suggestions? The vif line I'm currently using in my config is: vif = [ 'type=ioemu,bridge=eth0,model=ne2k_pci,script=vif-ovs' ] This works in my Windows XP SP3 VM, but is only recognized as a 10Mbit interface. Changing to model=e1000 or model=i82557b resulted in Windows not being able to find a driver for the NIC.

    Read the article

  • Why is this LTO4 Tape-drive not working

    - by Tim Haegele
    # modprobe mptsas # dmesg [ 4274.796796] scsi target7:0:0: mptsas: ioc1: delete device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4274.939579] mptsas 0000:01:00.0: PCI INT A disabled [ 4280.934531] Fusion MPT SAS Host driver 3.04.12 [ 4280.934552] mptsas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4280.934692] mptbase: ioc2: Initiating bringup [ 4281.490183] ioc2: LSISAS1064E B3: Capabilities={Initiator} [ 4281.490203] mptsas 0000:01:00.0: setting latency timer to 64 [ 4293.555274] scsi8 : ioc2: LSISAS1064E B3, FwRev=011e0000h, Ports=1, MaxQ=277, IRQ=16 [ 4293.574906] mptsas: ioc2: attaching ssp device: fw_channel 0, fw_id 0, phy 0, sas_addr 0x50050763124b29ac [ 4293.576471] scsi 8:0:0:0: Sequential-Access IBM ULTRIUM-HH4 B6W1 PQ: 0 ANSI: 6 [ 4293.578549] st 8:0:0:0: Attached scsi tape st0 [ 4293.578550] st 8:0:0:0: st0: try direct i/o: yes (alignment 512 B) [ 4293.578577] st 8:0:0:0: Attached scsi generic sg5 type 1 # mt -f /dev/st0 status mt -f /dev/st0 status mt: /dev/st0: rmtopen failed: Input/output error # dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 dd: opening `/dev/nst0': Input/output error I am running debian squeeze 2.6.32-5-amd64 #1 SMP Sun May 6 04:00:17 UTC 2012 x86_64 GNU/Linux Server is Fujitsu TX140 with Controller Symbios Logic SAS1064ET PCI-Express Fusion-MPT SAS Tape+Hardware is new.

    Read the article

  • Lenovo DVD Drive Disabled After Windows 7 Install

    - by David Lacher
    Upgraded hard drive in Lenovo T61P; decided to start fresh with Windows 7 Pro. Windows installed, so DVD drive was working. All of a sudden, driver is not recognized. Device is "HL-DT-ST DVDRAM GSA-U10N ATA Device". It appears on device manager but with the yellow tag; have tried uninstalling, searching for drivers, everything I can think of. Cannot even start over with Windows 7 installation disk because disk spins but then stops and My Computer does not recognize the drive. Help please. thank you. David Lacher

    Read the article

  • eSATA hotswap using Jmicron JMB363 controller

    - by Stephen
    I have tried both IDE and AHCI modes in the BIOS. Also tried many different driver revisions. I can't seem to hot swap an external SATA drive. I can use the wizard to safely remove it, but reconnecting doesn't do anything unless I reboot. I use a thermaltake dock, and I would like to swap in my backup drive sometimes to do images (they take all day over USB). I can reboot, but I'd like to use hot swap. The controller is a Jmicron JMB363. I'm using the latest BIOS on my motherboard, as well.

    Read the article

  • Having issues with flickering output to TV from Windows 7 laptop

    - by Nimmy Lebby
    I cannot tell why this is happening. I cannot get a pattern as to when it happens. Sometimes, I watch entire Hulu content without any interruptions. Other times, it happens 2-3 times in a span of 3 minutes. Then it stops for 10-15 minutes. Lenovo T410s Integrated graphics: Intel HD Graphics (Driver=8.15.10.2253, Video BIOS=2026.1) TV is a Zenith (does not happen with other laptop so doubt it's TV) TV connected to laptop using HDMI-to-DVI cable (previously was connected directly via DVI but I bought a new cable and it's still happening) Anyone could help me troubleshoot this? I'd greatly appreciate it. If you need more information, I'll be glad to provide it.

    Read the article

  • List all devices of system

    - by pareshverma91
    In my understanding linux can list only those devices which it can understand, i.e. for which the drivers have been installed. I think lspci is the command for that. But how can one figure out if there exists some device in the system for which the drivers are not installed and perhaps some hint about what that device is for and what driver would suffice for it. I would like to know this info so as to be able to recompile my linux kernel to a minimum and would like to avoid a hit and trial approach.

    Read the article

  • Windows Server 2008 Remote Desktop printing blank pages

    - by Colin Pickard
    I have a Windows Server 2008 (not R2) machine which has problems with redirected printing. Clients connecting via Remote Desktop have their printers redirected and appearing for them to print to, but printing from applications on the server to local printers is giving blank pages, missing pages, or pages with headers/footers but no middle section. The issues are consistant for similar prints, but sometimes other prints and/or applications will work correctly. I have installed PDFCreator locally on the server, and the same print jobs sent by the same application appear correctly in the PDFs. Printing that PDF via the redirected printer prints correctly. I have tried the following: Installing drivers. I’ve installed several drivers different drivers, for both the client and server operating system and architecture, on the client and the server. Reinstalling the printers. I’ve tried reinstalling on remote print servers, the clients, and the host server, and tried different client machines. Granting everyone full permissions on the print spool folder on the server. Editing the registry to forward non-USB ports (http://support.microsoft.com/kb/302361) None of these have made any difference. The clients are using Windows 7 or Windows XP and none of them have any issues with printing locally. Any ideas? Thanks!

    Read the article

  • Horizontal scrolling not working in Windows 7 running on MBP using Boot Camp

    - by Rubicon
    Is there a way to enable horizontal scrolling on Windows installed on a bootcamp partition of MBP 13" Core 2 Duo, using a trackpad? I had a look into the Boot Camp Control panel settings, but could not find a setting that suggested this. I used the Boot Camp drivers that came with the MBP in the Mac OS X Install disk. The vertical scroll is working fine, and the horizontal scroll works fine in the Mac world of things, so the hardware is fine. I think maybe there might be an additional install for a driver that we may have to install? Or any update? Thanks in advance for all your help. :)

    Read the article

  • New installation - Win 7 or directly Win 8?

    - by Horst Walter
    My laptop's hard disk is gone, so I need to re-install my Windows. Would it be a good idea to directly install Win8 (so actually the preview). Is there any known incompatibility with Win7 which would be a show stopper? I have a Dell XPS laptop, I do not expect any driver issues since the series is pretty much mainstream. Would the Win8 preview become Win8 RTM automatically by updates, or would I need to re-install Win8 RTM. This would be the no-go for me. The Win8 preview does not require a key, so I guess it becomes Win 8 RTM and then needs to be activated (which is what I want). Basically the idea is, I have to install windows anyway, so why not using the latest version?

    Read the article

  • Why do my speakers get distorted randomly on Windows 7?

    - by Daniel Fischer
    I have a studio monitor setup. I have 2 KRK 6's and a Focusrite Firewire Pro 24. Every few hours my speakers sound distorted and my solution has been go to sound levels Properties of Saffire Audio Device Advanced Default Format Toggle to 16 bit then back to 24bit. Why does it screw up every few hours? Sometimes one speaker doesn't output too and this same process resets it but that's more rare. Is this a OS issue or Focusrite Driver Issue?

    Read the article

  • How to tell X.org to reload input device module? (Working around suspend-to-ram crash on Acer laptop

    - by Vi
    When X.org boots up, Synaptics touchpad works well. But when I remove the module it falls back to /dev/input/mice and don't use normal driver even when touchpad is available again. Xorg.0.log: ... (II) XINPUT: Adding extended input device "Synaptics Touchpad" (type: TOUCHPAD) (--) Synaptics Touchpad: touchpad found # { rmmod psmouse && echo mem /sys/power/state && modprobe psmouse; } (WW) : No Device specified, looking for one... (II) : Setting Device option to "/dev/input/mice" ... How to tell X.org to try it's InputDevice again (without restarting X server)? P.S. rmmod psmouse is needed to prevent crashing of Acer Extensa 5220 when resuming from suspend-to-ram. Update: Found answer myself: Doing xinput set-int-prop "Synaptics Touchpad" "Device Enabled" 8 1 after reloading the kernel module reloads touchpad. Now suspend-to-ram works OK.

    Read the article

  • WHEA_UNCORRECTABLE_ERROR BSOD - what is wrong?

    - by Arcane
    Hello I have a problem with my PC getting the WHEA_UNCORRECTABLE_ERROR bsod. It is a few months old pc. I am not overclocking or changing anything in bios, but sometimes (this is my third time) I get this bsod out of nowhere. This last time I was just watching some stream on twitch when the pc suddenly crashed. I have everything up to date in windows update and every other driver as well. Everything in Open hardware Monitor seems ok. Right now as of 10 min after the crash, the CPU temp is at 38°C, fans are at 1400RPM I am using Windows 8.1 Pro 64b. Here are my spec: Intel i5-4570 CPU @ 3.20GHz, Kingston HyperX 8GB DDR3 1600 XMP, GeForce GTX 660 with 340.52 drivers, Corsair VS450 power supply, Gigabyte GA-H87-HD3 you can see the BSOD dump here: https://www.dropbox.com/s/88i1q2nnqnpzux1/082514-29656-01.dmp?dl=0 Can anybody tell me what is wrong?

    Read the article

  • How do I use wine's new multi-channel audio support?

    - by Forest
    Wine supposedly added Multi-channel support to the ALSA driver in a recent release. However, I haven't found any documentation about it or any reports of anyone successfully using it. I have 5.1 surround sound through ALSA (not Pulse) on my linux system, yet games in wine don't seem to use anything more than stereo, no matter which ALSA device I select in winecfg. Can someone explain what must be done to get wine games to use all my speakers for positional audio, or failing that, point me toward some useful documentation on the new multi-channel support?

    Read the article

  • Samba 3.5 Shadow Copy for Windows 7

    - by Prashanth Sundaram
    Over the past several days I have been trying to get the shadow to work with samba but haven’t been successful. Can someone check below config and let me know if I am missing something? We are using Equallogic SAN and iSCSI LUNS to mount volumes. I can cleanly access samba shares on Windows 7 clients but just not shadow copy. I have referred the official how-to but couldn’t get it to work. I see these messages in the logs. Any help is deeply appreciated. [2012/10/31 12:20:53.549863, 0] smbd/nttrans.c:2170(call_nt_transact_ioctl) FSCTL_GET_SHADOW_COPY_DATA: connectpath /fs/test-01, failed. [2012/10/31 12:21:13.887198, 0] modules/vfs_shadow_copy2.c:734(shadow_copy2_get_shadow_copy2_data) shadow:snapdir not found for /fs/test-01 in get_shadow_copy_data [2012/10/31 12:21:13.887265, 0] smbd/nttrans.c:2170(call_nt_transact_ioctl) FSCTL_GET_SHADOW_COPY_DATA: connectpath /fs/test-01, failed. == Samba pkgs == samba-3.5.10-116.el6_2.x86_64 samba-common-3.5.10-116.el6_2.x86_64 samba-winbind-clients-3.5.10-116.el6_2.x86_64 samba-client-3.5.10-116.el6_2.x86_64 === df –h == First is the iSCSI LUN and 2 others are snapshots. /dev/mapper/eql-0-fs-test01 5.0G 2.3G 2.5G 48% /fs/test-01 /dev/mapper/eql-2-0+fs-test01 5.0G 2.3G 2.5G 48% /fs/test-01/@GMT-2012.10.26-17.32.42/fs/test-01 (SNAPSHOT-1) /dev/mapper/eql-d-0+fs-test01 5.0G 2.3G 2.5G 48% /fs/test-01/@GMT-2012.10.31-11.52.42/fs/test-01 (SNAPSHOT- 2) ===/etc/samba/smb.conf === [global] workgroup = DOMAIN server string = Samba Server Version %v security = ads realm = DOMAIN.CORP encrypt passwords = yes guest account = nobody map to guest = bad uid log file = /var/log/samba/%m.log domain master = no local master = no preferred master = no os level = 0 load printers = no show add printer wizard = no printable = no printcap name = /dev/null disable spoolss = yes follow symlinks = yes wide links = yes unix extensions = no [test] comment = Test Directories path = /fs/test-01 vfs objects = shadow_copy2 #shadow_copy2: sort = desc #shadow: localtime = yes #shadow: snapdir = /fs/test-01/test #shadow: basedir = /fs/test-01 guest ok = yes writeable = yes map archive = no force create mode = 0660 force directory mode = 2770 inherit owner = yes inherit permissions = yes All feedback is welcome. Thanks!

    Read the article

  • no display on tv when connecting pc via hdmi in win7

    - by Kane
    The system of pc is win7 32bit, the video card is ATI 4670. The tv is philips 74xx series. And the monitor is Dell 19' that connect with pc via VGA. The tv can receive the singal and show the pictures when booting the pc(bios self checking, the logo of windows 7), however the tv says there is no signal after the win7 login window shows. I have installed the latest CCC and driver of ATI video card. Does anyone have idea for it?

    Read the article

< Previous Page | 199 200 201 202 203 204 205 206 207 208 209 210  | Next Page >