Search Results

Search found 17771 results on 711 pages for 'dhcp option'.

Page 217/711 | < Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• QoS for Cisco Router to Prioritize Voice and Interactive Traffic

  - by TJ Huffington

  I have a Cisco 891W NATing Voice and Data to the internet over a 10mbit/2mbit connection. Voice traffic gets degraded when I upload large files. Pings time out as well. I tried to configure a QoS policy but it's basically not doing anything. Voice traffic still degrades when upload bandwidth gets saturated. Here is my current configruation: class-map match-any QoS-Transactional match protocol ssh match protocol xwindows class-map match-any QoS-Voice match protocol rtp audio class-map match-any QoS-Bulk match protocol secure-nntp match protocol smtp match protocol tftp match protocol ftp class-map match-any QoS-Management match protocol snmp match protocol dns match protocol secure-imap class-map match-any QoS-Inter-Video match protocol rtp video class-map match-any QoS-Voice-Control match access-group name Voice-Control policy-map QoS-Priority-Output class QoS-Voice priority percent 25 set dscp ef class QoS-Inter-Video bandwidth remaining percent 10 set dscp af41 class QoS-Transactional bandwidth remaining percent 25 random-detect dscp-based set dscp af21 class QoS-Bulk bandwidth remaining percent 5 random-detect dscp-based set dscp af11 class QoS-Management bandwidth remaining percent 1 set dscp cs2 class QoS-Voice-Control priority percent 5 set dscp ef class class-default fair-queue interface FastEthernet8 bandwidth 1024 bandwidth receive 20480 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto auto discovery qos crypto map mymap max-reserved-bandwidth 80 service-policy output QoS-Priority-Output crypto map mymap 10 ipsec-isakmp set peer 1.2.3.4 default set transform-set ESP-3DES-SHA match address 110 qos pre-classify ! fa8 is my connection to the internet. Voice traffic goes over a VPN ("mymap") to the SIP server. That's why I specified "qos pre-classify" which I believe is the way to classify traffic over the VPN. However even when I ping a public IP while saturating upload bandwidth, the latency is exceptionally high. Is this configuration correct? Are there any suggestions that might make this work for my setup? Thanks in advance.

  Read the article

• Issues with doing a P2V on Exchange 2007

  - by PokermUNKEE

  I shutdown all Exchange services on the physical box and did a convert. Everything converted fine. Server booted up no issues and I could receive email from the outside world with no issues. But I am unable to send emails internally or externally. They just sit in the Outbox. I also disabled the DHCPClient service as I didn't want the server to get an IP address from DHCP when it first came online. It came online with no IP, then I used console to assign the correct static IP address (same one on the physical server) and rebooted. I ran the Exchange Troubleshooting Agent and it gave me the following errors: The value for the '\MSExchangeIS Mailbox\Messages Queued For Submission' counter on server exchange is greater than zero (average value is 8.8) and it appears that 'MSExchangeMailSubmission' is failing to submit messages to at least one computer with the Hub Transport server role installed over the last minute. Found 1 computers with the Hub Transport server role installed in the same Active Directory site as server exchange using local Active Directory site GUID 'ce8a4367-1bf6-4825-9cac-c4e2b115c450'. Check Local Active Directory Site Hub Transport Server Role Health (Mailflow_CheckLocalBhHealth1.1.1.1.1.1.1.1) I have one Exchange server with all the roles on it. Has anyone see this before when doing a convert? Please help :(

  Read the article

• How to handle payment types with varying properties in the most elegant way.

  - by Byron Sommardahl

  I'm using ASP.NET MVC 2. Keeping it simple, I have three payment types: credit card, e-check, or "bill me later". I want to: choose one payment type display some fields for one payment type in my view run some logic using those fields (specific to the type) display a confirmation view run some more logic using those fields (specific to the type) display a receipt view Each payment type has fields specific to the type... maybe 2 fields, maybe more. For now, I know how many and what fields, but more could be added. I believe the best thing for my views is to have a partial view per payment type to handle the different fields and let the controller decide which partial to render (if you have a better option, I'm open). My real problem comes from the logic that happens in the controller between views. Each payment type has a variable number of fields. I'd like to keep everything strongly typed, but it feels like some sort of dictionary is the only option. Add to that specific logic that runs depending on the payment type. In an effort to keep things strongly typed, I've created a class for each payment type. No interface or inherited type since the fields are different per payment type. Then, I've got a Submit() method for each payment type. Then, while the controller is deciding which partial view to display, it also assigns the target of the submit action. This is not elegant solution and feels very wrong. I'm reaching out for a hand. How would you do this?

  Read the article

• pfSense Firewall or Linsys/Cisco router for small offices

  - by Tim Meers

  I'm about to start switching some networks around for multiple small offices. Each office has about 10 to 15 users and 10 to 15 computers. Each office has a spread of generic routers and access points. The routers vary from being used as routers, to just being an access point for wireless. Nothing formal has really ever beem implemented for each of the 10 offices. What I'm wanting is to set up a pfSense box for each office to configure things like: traffic shaping (for VoIP QOS) URL Filtering DHCP static routing multiple VLANs I'll then use some of the existing hardware for wireless. Maybe even integrate the wireless right into the firewall depending on the office layout. So my question, would this be better to do a full blown firewall box, or but a new business class or high end consumer class Linksys router to do the URL filtering, QOS and DHPC? Each option could allow for remote access and VPN for remote maintnance and each would only cost a nominal about of money for something decent, i.e. under $250.

  Read the article

• kickstart: reference floppy drive via %ksappend or %include

  - by virtualeyes

  Having trouble getting %ksappend or %include to work when referencing a local floppy drive. Booting off remote server's cd-rom drive I am able to load the CentOS 6 minimal install image, and then add ks=hd:fd0/ks-jvm.cfg to boot params to load kickstart init file from floppy disk. That works fine. The problem is that I want to load a streamlined generic init file off the floppy and then, within the init, %ksappend or %include specific config files relative to the type of server I'm building (JVM, MySQL, Apache, etc.) I do not have DHCP, networking needs to be specified statically, so %ksappend and %include both fail when attempting to reference http://some-LAN-IP/foo.cfg since networking has not yet been set. The kickstart setup only works when I glob in the entire config into a single file, which is great, but ugly and difficult to maintain when I return later, having forgotten the original setup. At this point I'd be happy if I could get %ksappend or %include working with a floppy drive reference in the %post section; that would consolidate a lot of common boilerplate that all kickstarts will rely on (sshd_config, rsync config, resolve.conf, and so on) Thanks for providing the magic floppy drive reference that is eluding me!

  Read the article

• Recover a folder or file in TortoiseSVN whilst also retaining all history.

  - by Topdown

  In revision 1 a folder existed. In revision 2 the folder was accidently deleted and the change committed. We wish to roll back such that the folder is present, and retain its history. In the TortoiseSVN docs it indicates 'how' in the section titled "Getting a deleted file or folder back". To quote: Getting a deleted file or folder back If you have deleted a file or a folder and already committed that delete operation to the repository, then a normal TortoiseSVN - Revert can't bring it back anymore. But the file or folder is not lost at all. If you know the revision the file or folder got deleted (if you don't, use the log dialog to find out) open the repository browser and switch to that revision. Then select the file or folder you deleted, right-click and select [Context Menu] - [Copy to...] as the target for that copy operation select the path to your working copy. A switch retrieves the file into my working copy as one would expect, however there is no "Copy to" option on the context menu when I right click this working copy. If I open the repos browser, there is a copy to option, but it seems this simply takes a copy of the file. The solution I feel is to do a Branch/Tag, but if I try this from a prior revision to the same path in the repository SVN throws error that the path already exists. Therefore, how do I recover a folder/file in TortoiseSVN whilst also retaining all history. TortoiseSVN v1.6.8, Build 19260 - 32 Bit , Subversion 1.6.11,

  Read the article

• Per client DNS server assignment using Pfsense

  - by Trix

  I have a network where pfsense is the gateway. There are two sets of clients that I want. One where there will be some restrictions to the network (example, IM being blocked) and one network where there are no restrictions. One easy way I thought about doing this was assigning the different domains different DNS servers. One set could use OpenDNS, the other could use Google's Public DNS. The set with OpenDNS would have the filter options on (using OpenDNS' dashboard, I can check block IM .... so I do not manually need to block login.oscar.aol.com, meebo.com, gmail chat ....etc). So the problem is the DHCP server looks like it will only assign a single set of DNS servers to clients. Is there a way to set a per client assignment? Is there a better way to obtain what I want to obtain. This is just a small home network. I do not need anything fancy, but I do need this functionality in one way or another.

  Read the article

• Modify registry for Internet Connection Sharing?

  - by Tim

  My OS is Windows XP. Quoted from How to Change the IP Range for the Internet Connection Sharing DHCP service Use Registry Editor to modify the data value of the IntranetInfo value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Settings\General The first number listed is the IP address of the internal IP address of the Connection Sharing host. The second number is the subnet IP address separated by a comma. Enter the first IP address of the new range followed by the subnet mask, separated by a comma. (For example, 169.254.0.1,255.255.0.0.). Modify the data value of the Start value in the following registry key: Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing\Addressing\Settings Change the value to the second address of the selected IP range. This address cannot be the same or a lower value than the IP address used for the IntranetInfo key. Modify the data value for the Stop value in the same registry key. Enter the last the IP address of the selected IP range. My registry table does not have Hkey_Local_Machine\System\CurrentControlSet\Services\ICSharing, and I don't know how to do with my registry table following the above three steps. Can someone guide me through it step by step?

  Read the article

• Perl on MacOS X 10.6.2: GDBM_File missing, how to install or work around?

  - by jdmuys

  When I need a Perl module, I typically use CPAN. It works fine. But not this time. I want to use MARC::Charset, but this one uses GDBM_File, and I can't seem to install GDBM_File from CPAN. CPAN finds it all right, but trying to install it, it starts installing the full Perl 5.10.1 distribution. MARC::Charset is a rather old module, so there should be a way to use it from some common Perl version (Mac OS X 10.6.2 has 5.10.0 and 5.8.9 by default). While installing the full blow Perl 5.10.1 is not an option, modifying MARC::Charset to stop using GDBM_File might be one. What would be the best course of action to do so? This last option might also be the only one. googling GDBM_File uncovers a few items that suggest that gdbm is not even available on the Mac. Those items typically went over my head though. While I don't expect a silver bullet, somebody may have a pointer or two on where I should start. After all, MARC::Charset only does character transliteration to/from the marc8 char set, which unfortunately, iconv doesn't seem to support.

  Read the article

• How can I use Linksys WPSM54G print server as a bridge for another machine AND also share the printe

  - by user26453

  I have a Linksys WPMS54G currently sharing a printer via the USB port with the rest of my network via the wireless. Is there any way to set it up so that the ethernet port is bridged over the wireless adapter portion? i.e., be able to uplink another machine or switch into the network via the WPMS54G's ethernet port? Update: The network architecture is as follows: (1) Linksys WRT54G router that serves as a router, DHCP server, and wireless access point for the network. Fairly standard configuration (3) Laptops that are used throughout the house via wifi (1) Linksys WPSM54G printer server that connects via wireless to the router, in a separate room with a printer attached to print seerver's USB port along with (1) Un-networked desktop in the same room Since the printer is plugged into the USB port of the WPSM54G, I am wondering if I can connect the desktop to the ethernet port of the WPSM54G and have it bridged over the wifi to the router. The twist here is that the ethernet is initially used to connect the wireless print server to the router (for configuration, can't configure it wirelessly if you are initially on a encrypted network). Now instead of using that ethernet port as a way to connect the print server to the network (via the router), I want to use the ethernet port as a way to connect another computer to the network, in effect bridging into the router via the print server, while still sharing the printer (attached via USB) through the print server. If this is not clear, please comment. To be clear, the computer I want to connect/bridge into the network does not have a wireless card, is far from the router, and I do not want to lay ethernet cable to connect it. While I could certainly buy a legitimate wireless bridge to accomplish this, I figured since the print server already has an ethernet port, see if I can't use that.

  Read the article

• Sort multiple columns while using a bindingsource or bindinglist

  - by JF

  Hi everyone. I have a problem I am trying to fix and it's sorting a DataGridView on multiple columns. I have read that this option is not a feature built-in the DataGridView and I have to implement it. I have found multiple solutions, but none quite got to do the work. I'm also quite a newbie in C# and I don't know much of the .Net library. I have also read on the MSDN site for info on different classes that might be of use, but no success. Now, let's get to the point. I have a DataGridView, with a BindingList (originally, a BindingSource) that I want to sort, but by multiple keys. My DataGrid has 9 columns and the user should be able to sort on any column. For example, let's say my Datagrid has 3 columns, named : Index, ID, Name. The user wants to sort by Name, implicitly, the next order would be Index and then ID. So, in case 2 names are identical, Index should be the next sort option. Any ideas how this can be made?

  Read the article

• How do I use a Zyxel P660 router as just modem so that I can connect a WRT54GL router in cascade?

  - by Kenji Kina

  I have a Zyxel P660HW-t1 v2 router (which has a DSL port) and a WRT54GL router (which does not) and the exact same situation as in this thread (UPDATE: the connection between both devices is the important part, since I have been able to set the zyxel router to act as bridge by itself quite nicely. I have accessed my internet connection directly through a PC using PPPoE without any problems, the issues arise when I try to connect the WRT54GL router between the zyxel "modem" and my PCs). I've been trying to use my Zyxel P660 as a modem only: Setup P660 to bridge mode. Changed WRT54GL's IP address to 192.168.2.1 to avoid a conflict on the network. Configured the PPPoE settings as required on WRT54GL. The thing is that when I connect the Zyxel modem/router on the WRT54GL's internet port the light doesn't turn on. I can confirm that this port has been working ok, so I'm not really sure what's going between the devices. I checked several settings such as IPs, tried disabling DHCP on Zyxel/Linksys, Firewall on both and still nothing. Also, I tried connecting Zyxel directly to a computer in bridge mode and dialed successfully. I have even posted a question here before, thinking that what I asked there was the only thing I needed to get things done. Unfortunately it wasn't, and the guy that solved his issue didn't give enough details in his post (and is quite unlikely to give more details since he was an anonymous user). For one, I don't know how to do this part: connected to the Zyxel through telnet and forced LAN port 1 to be at 100mb as well I can't find the option that does this on the zyxel router. Not through telnet or the web admin. Can anyone help me solve this?

  Read the article

• Static routing on a TP-Link TL-WR1043ND

  - by igor

  My home network setup looks like this: Both routers are TP-Link TL-WR1043ND routers. The basement router handles all devices in the house that are connected via cable, handing out addresses for the 10.89.49.0/24 network via DHCP. Wireless doesn’t really work from the basement, as the signal is too weak, so I have disabled it. To do WiFi, I have added a second (identical) router downstairs. On the WAN side it is assigned the 10.89.49.101 IP address from the basement router, and on its LAN it provides the 10.89.7.0/24 network. Basic internet access works flawlessly from any device this way. I am now facing the problem that I am not able to communicate (e.g. SSH) between all devices, wired or wireless. I am able to connect from a wireless device to a wired device, for example SSH-ing from 10.89.7.X to 10.89.49.Y, but it doesn’t work the other way round—despite the fact that I have added a static route to the basement router: Does anybody have any idea on how to solve it? Both routers have already been upgraded to use the most recent firmware from TP-Link.com (Build 110429), to no avail. Errata: I would like to stick with the official firmware, switching to something like DD-WRT or OpenWrt only as a last resort.

  Read the article

• Looking for a good world map generation algorithm

  - by FalconNL

  I'm working on a Civilization-like game and I'm looking for a good algorithm for generating Earth-like world maps. I've experimented with a few alternatives, but haven't hit on a real winner yet. One option is to generate a heightmap using perlin noise and add water at a level so that about 30% of the world is land. While perlin noise (or similar fractal-based techniques) are frequently used for terrain and is reasonably realistic, it doesn't offer much in the way of control over the number, size and position of the resulting continents, which I'd like to have from a gameplay perspective. See http://farm3.static.flickr.com/2792/4462870263_ff26c40365_o.jpg for an example (sorry, can't post pictures yet). A second option is to start with a randomly positioned one-tile seed (I'm working on a grid of tiles), determine the desired size for the continent and each turn add a tile that is horizontally or vertically adjacent to the existing continent until you've reached the desired size. Repeat for the other continents. This technique is part of the algorithm used in Civilization 4. The problem is that after placing the first few continents, it's possible to pick a starting location that's surrounded by other continents, and thus won't fit the new one. Also, it has a tendency to spawn continents too close together, resulting in something that looks more like a river than continents. See http://farm5.static.flickr.com/4069/4462870383_46e86b155c_o.jpg for an example. Does anyone happen to know a good algorithm for generating realistic continents on a grid-based map while keeping control over their number and relative sizes?

  Read the article

• OpenVPN and TomatoVPN

  - by Bill Johnson

  Wondering if someone can help me with the following. I have updated my Linksys router with TomatoVPN and used the following config: Interface Type:TAP Protocol:UDP Port:1195 Firewall Custom Authorization Mode:Static Key I have then inserted the static key generated in OpenVPN saved and started the service. connect.ovpn. # Use the following to have your client computer send all traffic through your router # (remote gateway) remote (entered my DNS/DHCP servers external IP address here) port 1195 dev tap secret static.key.txt proto udp comp-lzo route-gateway 192.168.1.1 redirect-gateway float I've then placed my static key in a file in the same directory as your connect.ovpn (static.key.txt) Now OpenVPN is installed on a laptop that I use at home. I have plugged in the laptop to my home connection and started connect.ovpn The Local Area Connection is connected as 'Home Network 3' - and when I start OpenVPN it is connected as 'Local Area Connection 2' and this is showing as 'Unidentified Network' and it appears there is no network access. TAP-Win32 Adapter V9 appears to be the adaptors name and the IP and DNS properties are set to automatic. If I open up the OpenVPN GUI it shows an error message saying "Connecting to connect has failed". Looking at the error message behind this pop-up one line says "TCP/UDP Socket bind failed on local address [undef]:1195 Address already in use [WSAEADDRINUSE] Could anyone possibly help me further with this please?

  Read the article

• using text and ntext SQL Datatypes in RPG

  - by David Stratton

  I'll preface this with saying that I'm a .NET developer, and am NOT an RPG developer. I'm working with one of our RPG developers to come up with a solution, so any suggestions you provide will get passed to him. We have a scenario where we want our iSeries to read from a SQL Server database. One of the columns is a TEXT column. IN RPG, there is no equivalent data type to use for this. We've gone back and forth on this, and our current plan is to change course, and have our SQL Server write out a text file, which the iSeries can pick up and parse. This is, however, a last resort option, as the data in the file is sensitive, and we'd like to avoid the additional security overhead. We've already got the SQL Server locked down as tight as possible (one user only has read access to this, and that user is an iSeries user.) We don't want to have to worry about transferring files back and forth. However, at this point, we see no other option. We have no in-house Java developers, and need to do this in RPG. So I'm wondering if there are any RPG developers out there who have faced this situation and have any advice.

  Read the article

• How do I get more information on a potential network freeloader?

  - by Dov

  I have a home network set up, complete with a relatively good password. I'm in Mac OS X 10.6 (Snow Leopard) and have been noticing, on occasion, a computer showing up in my Finder's Shared section, that is not one of my own (the "pe-xpjalle" box pictured below). He has a tendency to come and go. How can I figure out his MAC address or something, so I can block him? I checked my "Logs and Statistics" in the Airport Utility, and didn't see that computer under DHCP clients. I'd rather not change my password, since I have quite a few devices I'd have to update. Is there any other reason he's show up on my network besides having guessed my password? Update: I fixed the Dropbox URL above (how embarrassing, I'm new to Dropbox. Thanks for the heads up, Doug.) Update 2: I tried clicking on "Connect as..." just for the hell of it, and got the dialog below. Now I have even less an idea what's going on than before. I don't have Parallels of VMware running, just the following: Transmission, NetNewsWire, Mail, Things, Safari, iTunes, Photoshop, Pages, Yojimbo, Preferences, AppleScript Editor, Software Update, Airport Utility, and Terminal. I don't think any of those create a virtual network machine, right? And no VMware machine of mine has ever had a name resembling "pe-xpjalle". Update 3: I just changed my passwords on both my N- and G-only networks, and I'm still seeing this, so I highly doubt that it's someone who's figured out my password (twice now). I'm really stumped.

  Read the article

• Web server with static IP from cable provider

  - by Dmitri

  I have a subscription to 5 static IP addresses. I want to run a web server from behind a router. My network config is as follows: Server's local address is 10.1.10.2, has IIS running on it, port 80 and 443 (IIS is not my fault, had to be done) the server's ip address is static, the subnet mask is 255.255.255.0, gateway is 10.1.10.1, which is the local address of the cable modem / router / gateway thingy. All looks to be in textbook order as far as the LAN goes. I can get to anything on my LAN from any computer on my LAN, whether they have static IP or get it through DHCP from the cable modem/router thingy. however, I have no internet access form any of my LAN computers. I called Comcast tech support and they say they can connect to my modem/router just fine and can actually use it to ping any computer on the internet or any computer on my LAN from the router/modem (i checked, myself, this is in fact the case). However, nothing on my LAN has internet connectivity. I tried pinging the DNS servers, nothing. I tried directly typing in web sites' IP addresses, nothing, so doesn't seem to be a DNS issue. Any Ideas? What malfunction of a router could be causing such weird behavior? nay ideas or educated guesses are very much appreciated.

  Read the article

• OpenVPN via DD-WRT

  - by user140491

  I am using DD-WRT with my Buffalo G300NH. I notice in my log files: Wed Oct 10 01:08:25 2012 us=343000 Cannot open /tmp/openvpn/dh.pem for DH parameters: error:02001003:system library:fopen:No such process: error:2006D080:BIO routines:BIO_new_file:no such file I have looked at other answers regarding this error. I have tried to no avail. 755 are chmod rights to /tmp/openvpn. At this point, I can not connect outside my LAN via OpenVPN. My server config looks like this: #mode server #tls-server push "route 192.168.11.1 255.255.255.0" push "dhcp-option DNS 10.8.0.1" server 10.8.0.0 255.255.255.0 port 1194 proto udp dev tun0 ifconfig 10.8.0.1 10.8.0.2 #secret /tmp/static.key ca /tmp/openvpn/ca.crt cert /tmp/openvpn/cert.pem key /tmp/openvpn/key.pem dh /tmp/openvpn/dh.pem keepalive 10 120 comp-lzo persist-key persist-tun verb 5 management localhost 5001 Can someone, knowledgeable, of this error kindly help? i have been going on several days, trying to sort it out. I like all nighters though!!

  Read the article

• Can VMWare Server 2.0 be useful in Production for easing backups?

  - by Keith Sirmons

  Howdy, Let's run this idea by the group here. I am thinking about using VMWare Server in production to host a 2008 Domain Controller with DHCP and DNS, a 2008 member server with WSUS, some virus software, and other "management" utilities a second 2008 member server with SQL, IIS, and File Shares for a medium business of 50-100 desktops. The reason I am leaning toward Server vs ESXi is for backup purposes. Using ESXi, if I want to backup the VM's, I would need a second server in the office with enough storage availability to hold a copy of the vmdks. I am wondering if putting this virtual environment on top of a basic 2008 server install will allow for easier backups to both tape and/or to offsite storage using JungleDisk. Can a snapshot be triggered easily via a scheduled job? I know this doesn't necessarily handle file level restores, but I want to make sure in a DR situation, we can restore production servers quickly. Does this concept hold water? Would a very minimum install of the 2008 Host remove too many resources from the actual production machines? This would be a new Dell 410 server with 12 GB ram and (6) 600 GB 15K in a RAID 6, Dual Intel Xeon 2.26GHz procs.

  Read the article

• Vista ICS issue

  - by Bill Grey

  I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

  Read the article

• Building Cross Platform app - recommendation

  - by Ben

  Hi, I need to build a fairly simple app but it needs to work on both PC and Mac. It also needs to be redistributable on a disc or usb drive as a standalone desktop app. Initially I thought AIR would be perfect for this (it ticks all the API requirements), but the difficulty is making it distributable, as the app would require the AIR runtime to be installed to run. I came across Shu Player as an option as it seems to be able to package the AIR runtime with the app and do a (silent?) install. However this seems to break the T&C from Adobe (as outlined here) so I'm not sure about the legality. Another option could be Zinc but I haven't tested it so I'm not sure how well it'll fit the bill. What would you recommend or suggest I check out? Any suggestion much appreciated EDIT: There's a few more discussions on mono usage (though no real conclusion): Here and Here EDIT2: Titanium could also fit the bill maybe, will check it out. Any more comments from anyone? Ben

  Read the article

• Server 2003, XP Clients, DNS issues

  - by ron

  Hello, Im having DNS issues on my network. My DC is my DNS server 10.76.4.11 and recently I configured a forwarder to 10.4.36.10. My workstations are not working because they cannot resolve the domain controller name because of DNS. an ipconfig /all reveals that they know the IP of the DNS server is 10.76.4.11, but if I nslookup 10.76.4.11 it forwards the request to 10.4.36.10 and goes nowhere. I have since removed the forwarder, but still any nslookup requests on workstations are going to 10.4.36.10. If I nslookup 10.76.4.11 on the server it can resolve its name, but for some reason when it receives the same request from workstations it doesnt know what to do. All the A, CNAME records etc are correct. DHCP's DNS is set correctly, GPOs are correct (even though they cant refresh cos of this problem!), the servers network adapter has its DNS set to 10.76.4.11. Just don't know. Very confused.

  Read the article

• Good DB Migrations for CakePHP?

  - by Martin Westin

  Hi, I have been trying a few migration scripts for CakePHP but I ran into problems with all of the in some form or another. Please advice me on a migration option for Cake that you use live and know works. I'd like the following "features": -Support CakePHP 1.2(e.g. CakeDCs migrations will only be an option when 1.3 is stable and my app migrated to the new codebase) -Support for (or at least not halt on) Models with a different database config. -Support Models in sub-folders of app/models -Support Models in plugins -Support tables that do not conform to Cake conventions (I have a few special tables that do not have a single primary key field and need to keep them) -Plays well with automated deployment via Capistrano and Git. I do not need rails-style versioned files a git versioned schema file that is compared live to the existing schema will do. That is: I like the SchemaShell in Cake apart from it not being compatible with most of my requirements above. I have looked at and tested: CakePHP Schema Shell http://book.cakephp.org/view/734/Schema-management-and-migrations CakeDC migrations http://cakedc.com/downloads/view/cakephp_migrations_plugin YAML migrations http://github.com/georgious/cakephp-yaml-migrations-and-fixtures joelmoss migrations http://code.google.com/p/cakephp-migrations

  Read the article

< Previous Page | 213 214 215 216 217 218 219 220 221 222 223 224  | Next Page >