Search Results

Search found 1167 results on 47 pages for 'modem'.

Page 22/47 | < Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >

  • Can a website become popular in a "category" (ie, not just a single page)

    - by Earlz
    I have a few keywords where my website is high ranking(2nd and 3rd result). For instance, I have 3 blog posts covering a certain kind of modem. Is it common for search engines to consider a website popular in a "category"? For instance, if I was the first result for "foobar" with one page, and then added another separate page which mentioned "foobar"(and maybe a link from the original page), would a search engine prioritize this separate page when compared to a completely separate website with a page with the same content?

    Read the article

  • Cisco: Site-to-site VPN with cisco 878 and ASA weirdness

    - by cpf
    I currently have 2 sites, both connected to each other through 2 firewalls / routers in a site-to-site VPN. Pinging from server to server (Using 2mb/2mb SDSL) through that VPN obviously works, however, at one site, we have another internet connection (7m/400k ADSL), and only the link between the two sites should be on the other connection. All pc's should go over the other connection for internet, just communication between servers & Communication between pc's and the server at the other side should go through there too. What is configured at the moment is the server is using the SDSL directly as default gateway. Since it's not intended to surf anything it is a safe config. PC's are configured on the ADSL as default gateway. Now I wanted to route through everything that uses the range used on the other site, it should be sent from the ADSL modem to the SDSL modem, which has the VPN connection. I figured I could use OSPF to do so, however, OSPF doesn't seem to "detect" the range of the external site. Also (due to bad ip subnetting thanks to the other administrator), the ip used internally as the server on the other site also exists on the internet (causing a lot of confusion), so rdp-ing from our server to the server of the other site works (somehow), but tracerouting on the SDSL router (which should actually, in my opinion, go over the VPN) actually goes all over the internet. My question(s): Why doesn't the SDSL router ping the external ip through VPN, but the server does? Why can't I route from the ADSL router to the SDSL over VPN? I would seriously appreciate some help, since I can't figure out why it does it like this.

    Read the article

  • No internet connection using Edimax routers

    - by idan315
    I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. I am really lost on how to approach this problem. Possible leads: when I view the network information, I see that my computer is connected to 'Multiple Networks'. One of those is "Network 4" (probably my router), and the other is Unidentified network. I don't know how to make the "Unidentified Network" disappear, or why is it even there in the first place. When I try using "ipconfig", I have two default gateway IPs. The first is 0.0.0.0, and the second is the IP of my router (192.168.2.1). The first router was Edimax BR-6204Wg. The second one I've tried connecting is BR-6424n. Any ideas?

    Read the article

  • Vista ICS issue

    - by Bill Grey
    I have a strange problem with Internet Connection Sharing on a laptop running Vista Business. This laptop is connected to the internet via the ethernet port, which goes to an ADSL modem. it is automatically assigned the IP address 192.168.1.50, and the modem/gateway is 192.168.1.1 My friends laptop is running Vista Home. Previously, I would create an ad hoc wireless network, enable ICS, and everything would be perfect. My friend would have internet access via this. However, something has now mysteriously broken. If I enable ICS on the wireless connection, it resets my Local Area Connection, assigning it the manual IP address of 192.168.0.1, which means my connection to the internet is destroyed. Both wireless adapters on each network are assigned auto configuration addresses, in the 168. range. They can see each other fine, but my friends laptop cannot access the internet via mine, even after I have restored the Local Area Connection settings. I understand the computer with ICS enabled must have the IP of 192.168.0.1, but previously, before whatever went wrong, my wireless adapter would be 192.168.0.1 and my friends computer would get an IP via DHCP. I have also tried setting static IP address and making a bridge, none of which works. How can I fix this problem, and prevent enabling ICS from touching my Local Area Connection? Both machines have no firewall, have appropriate settings etc...

    Read the article

  • How can I calculate power consumption of my PC in Watt?

    - by Jitendra vyas
    How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

    Read the article

  • VPN Error 619: Behind Cisco Router WRT310N

    - by ty91011
    I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

    Read the article

  • Can I make two wireless routers communicate using the wireless?

    - by Dana Robinson
    I want to make a setup like this: cable modem <-cable- wireless router 1 <-wireless- wireless router 2 in another room <-cables- PCs in another room Basically, I want to extend my network access across the house and then have a bunch of network jacks available for my office PCs. Right now, I have a cable modem going to a wireless router in one room and a PC with a wireless PCI card in it in the office on the other side of the house. I use internet connection sharing with the other PCs in the office. The problem is that ICS is flaky, especially when I switch to VPN on the Windows box to access files at work. I picked up a wireless USB adapter that I thought I could share among the PCs I work on but I'm not very happy with it so I'm going to return it (NDISwrapper support for it is poor). Is this possible? My wireless experience so far has been pretty straightforward so I have no idea what kind of hardware is available. I've looked at network extenders but those just look like repeaters for signal strength. I want wired network jacks in my office.

    Read the article

  • When I ping Internet addresses like yahoo or Google, I get 2 reply packets and 2 lost packets.

    - by navi
    I have Airtel broadband and a Tata broadband connection. i have around 50 PCs connecting through an airtel broadband connection. Both are dsl connections with my phone line going into dsl modems and an Ethernet cable going from dsl modem directly into a switch. Currently, only airtel connection is connected with static IP on my private lan and using the airtel ISP DNS servers as DNS IP address and the default gateway is 192.168.1.1 (IP add. of the dsl modem). All PCs are connected in a work group. When in full use, my users complain of certain web pages are not opening. When I ping Internet addresses like Yahoo or Google I get 2 reply packets and 2 lost packets. I suspect that a single broadband connection is not able to sustain 50 simultaneous downloads/browsing. Is there any device which connect to both DSL and make one line so that its give me high speed simultaneous browsing. Help needed urgently. Thank you all to those who reply.

    Read the article

  • ADSL with RFC 2684 Bridging

    - by Axel Isouard
    My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

    Read the article

  • Hints on diagnosing performance issue in OpenBSD firewall

    - by Tom
    My OpenBSD 4.6 pf firewall has started having really bad performance in the past few weeks. I've isolated the firewall (as opposed to the WAN connection, switch, cable, etc.) as the problem, but need a hint on how to further diagnose or fix the problem. The facts: Normal setup is: DSL Modem - FW Ext. NIC - FW Int. NIC - Switch - Laptop Normal setup described above gives only 25 Kbps! Plugging the laptop straight from the DSL modem gives a 1 MBps connection (full speed, as advertised). Therefore, the DSL connection seems to be OK. Plugging the laptop directly into the firewall's internal NIC (bypassing the switch) also gives only 25 Kbps. Therefore, the switch does not seem to be a problem. I've replaced the ethernet cables, but it didn't help. Here's the weird thing. Reloading the ruleset (/sbin/pfctl -Fa -f /etc/pf.conf) causes the laptop's connection to go up to 1 Mbps (i.e. full speed) for a few minutes before it gradually degrades back down to 25Kbps again. Any ideas on what's wrong or how I could further diagnose the problem?

    Read the article

  • Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

    - by PJZ
    Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

    Read the article

  • Having trouble setting up my router

    - by indyK1ng
    I just moved into my apartment and the Internet connection is working. It's Comcast in case that matters. Anyway, I'm having trouble setting up my wireless router (Netgear WNR2000) to work with it. Are there any settings that I could be missing? I currently have it set up to use a static IP address and I found the DNS servers I'm supposed to use and the Internet light is green, but I can't get out to the Internet. When I am trying, I'm connecting to an Ethernet port on the back of my router. Is there a setting I'm missing or a setting that I have set wrong? I used the automatic set up wizard to learn that it's a static IP address. Any help would be appreciated. I am currently only able to use my Linux machine, so please make any help in Linux commands. Yes, I can connect to the Internet if I connect to the modem directly and I've been using the web interface when I'm connected to the router, so I suppose I can ping the router. My router detected the connection as using a static IP address, so I connected to the modem directly and figured out what my IP address, gateway, and mask were as well as DNS servers.

    Read the article

  • Mac WLAN 802.11b+g WPA1 connection issues

    - by Peto
    Hi, I have a Telewell TW-EA510v4 ADSL modem+WLAN router configured as follows: Mode: 802.11b+g Security Mode: WPA1 Pre-shared Key WPA Algorithms: TKIP Connections from only certain MAC addresses have been allowed and the MAC address of my Mac is in that list. The WLAN works just fine with iPhone and an old Acer laptop. It has worked for about two months or so with my MacBook Pro (year and a half or so old model). Ocassionally i've had minor problems with it, which have required either reboot of ADSL modem or reboot of my Mac. However now, for the last week or so I haven't been able to connect to it at all. This is what is what i get in the console when i try to connect: 5.5.2010 20.54.53 airportd[73731] Apple80211Associate() failed -3924 (Invalid PMK) 5.5.2010 20.54.53 Apple80211 framework[584] airportd MIG failed (Associate Event) = -3924 (Invalid PMK) (port = 104599) 5.5.2010 20.54.53 SystemUIServer[584] Error joining WLAN-M: Invalid password (-3924 Invalid master key) The pre-shared key I use is not incorrect. I'm 100% sure of that. The Error Log from the router only says this when I try to connect to it: May 05 21:09:54 home.gateway:i802_1x:none: <my mac address> associated May 05 21:10:00 home.gateway:i802_1x:none: <my mac address> disassociated May 05 21:10:01 home.gateway:i802_1x:none: <my mac address> disassociated Any ideas or tips to troubleshoot this further?

    Read the article

  • How to set up a serial connection to a Windows 7 computer

    - by oli_arborum
    I need to set up a "dial in" connection to a Windows 7 (Ultimate) computer via a serial null-modem cable to be able to connect from a Windows XP client to that computer and exchange data over IP. Question 1: How do I do that? I did neither find the information via Google nor in the MSDN. Seems like no one tried ever before... ;-) I already managed to install a legacy modem device called "Communications cable between two computers" and found the menu entry "New Incoming Connection..." in Network and Internet Network Connections. When I finish this wizard I get the message that the "Routing and Remote Access service" cannot be started. In the event viewer I see the following error messages: "The currently configured authentication provider failed to load and initialize successfully. The requested name is valid, but no data of the requested type was found." (Source: RemoteAccess, EventID: 20152) "The Routing and Remote Access service terminated with service-specific error The requested name is valid, but no data of the requested type was found." (Source: Service Control Manager, EventID: 7024) The Windows 7 installation is "naked", i.e. no additional software or services are installed. Question 2: Am I on the right path to set up the connection? Question 3: How can I get the Routing and Remote Access service running?

    Read the article

  • Correct way to set up office network - 8 workstations, a file server and a staging server

    - by naunu
    Our office had this old school windows 2003 domain setup, our server caught fire, and now we are looking to do it right from scratch. Here is what we need: 5 PC and 3 Mac workstations for web development, they will each have WAMP/MAMP setup on them, managed by their developers. We will have a file server for assets, and a LAMP server with an external IP for staging. Here is what we have to work with: 5 IP addresses, brand new PC file server with windows 2008 SE, D-Link DSS-16+ 16 port switch, belkin 5 port wireless router, cable modem with 4 ports. How I have it set up now (this is a temporary makeshift setup): Cable modem = LAMP server, wireless router Wireless router = Switch = All of the workstations and file server (setup as a workgroup). We have noticed our internet is very slow with us all plugged in to the switch, and the switch plugged in to the router. I am not positive, but I think it is because our router does not have NAT. We are also having problems with the MACs connection to the network drive - it keeps disconnecting. I want this done right, and we have a ~$600 budget to buy anything else we need. Does anybody have any advice for me? Should I set up a domain or workgroup?

    Read the article

  • Very strange networking problem in all computers in my house

    - by Anthony
    I have three computers in my house: One desktop (wired), and two laptops (wireless). I'm using Cox Communications (yes they suck), and yesterday they had a major outage. I know it was them because I called them up when I started losing connection to the internet. All the computers can connect just fine, but they don't have internet access. It just says "local only". The weird thing is, some of them work occasionally. For the first day my laptop was working perfectly, while all the other computers couldn't connect. Later on in the day it got reversed, and the desktop was the one with internet access. By the second day the problem on Cox's end was fixed, but we still had no access. I called them up and they reset my modem, and did the usual troubleshooting stuff. It never fixed the problem, but we found out that the problem had to do with conflicting IP addresses. My router was a Linksys WRT54G and it was about 5 years old. I figured it might have gotten damaged from the outage since it was so old, and now it's having trouble "fixing itself" and giving out the proper IP addresses. So I bought a new router, a Cisco Linksys E1000. I set everything up, and still the same problem. My computer has access right now (that's how I'm writing this), but no other computers seem to be able to get access. Is there possible damage to the modem? Can someone help me please? Sorry for this being so long.

    Read the article

  • Extending home network using multiple access point originating from another access point

    - by cyberjar09
    I have a home network with the current setup (RJ45 running from main router to access point) : +-------------+ +--------------+ | 192.168.2.1 | |192.168.2.2 | | router +--------------->access point 1| +-----^-------+ +--------------+ | | +-----+--------+ | 192.168.1.1 | | modem | +-----^--------+ | | | | +--+--+ | ISP | +-----+ However I would like to extend the network to two more floors in the house via the existing Access Point (router is too far and not reachable using a network cable, hence I need to extend using current access point). Please see diagram below : +-------------+ +--------------+ +----------------+ | 192.168.2.1 | |192.168.2.2 | | 192.168.2.3 | | router +--------------->access point 1+----------> access point 2 | +-----^-------+ +--------+-----+ +----------------+ | | | | +-----+--------+ | | 192.168.1.1 | | | modem | | +-----^--------+ | +----------------+ | +----------------> 192.168.2.4 | | | access point 3 | | +----------------+ | +--+--+ | ISP | +-----+ Q1 : is this setup possible? Q2 : if possible, will I have to do anything different from what I did to setup access point 1? edit 1 : I am trying to study the dd-wrt documentation to see which would be the correct mode of operation for me Linking Routers but Im confused because I dont see any info on how to use an existing Access point to extend the signal of the SSID. If anyone could point me to the correct wiki for how I should setup AP2 and AP3 based on AP1, it would be very helpful. For AP1, I did the following Use static IP and setup same SSID as primary wireless router use same security as primary wireless router make AP1 point to 192.168.2.1 (primary router) for DHCP Thanks in advance.

    Read the article

  • network latency, TCP and UDP packets

    - by user115848
    Hello recently my network has started to cause me lots of problems. I have a cable modem, connected to a tp-link router (with some port forwarding). Everything was working fine then i started to get lots of udp (port 53) "UNREPLIED" logs in the router. Now there are tcp UNREPLIED logs too. This is causing lots of latency and failed connections when trying to connect to different internet sites. Also, we run an openfire server for spark connections, and I believe its causing connectivity issues for some users who are trying to connect using Spark (some people connect fine, others don't). Please see screen shot below for packet logs. It has to be something internally, as I connected straight to the comcast modem and i was able to connect to the internet and various sites as normal. I tried to swap out the router with a different and got the same issue. I scanned both my internal dns servers for viruses or malware and it came up empty. Another anomaly is that when i try to connect to www.cnn.com, i get redirected to the different site. I scanned my own machine for hijacks. Not sure if this is related to the networking issue. Please let me know if you have any ideas for troubleshooting.

    Read the article

  • Private staff network within public network

    - by pianohacker
    I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

    Read the article

  • pppd disconnects from 3G, doesn't reconnect, w/ persist set

    - by bytenik
    I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

    Read the article

  • Wireless connection drops when wired computer starts a game.

    - by Skadlig
    Starting this week I have had a strange problem on my network. Some background of my setup: Internet is provided by a adsl-modem. A D-link Dir-600 router is hooked up to to adsl-modem. My computer is hooked up to the router using a cat-5 cable. My wife's computer is hooked up using a wireless usb dongle, TP-Link TL-WN821N. Both computers use windows 7 64-bit home premium. Up until this week everything was normal, we could for instance play Dungeons & Dragons Online together without any network issues. Now every time I start DDO or any other network game, for instance L4D, the whole wireless network drops. I have confirmed that it's not just her computer using an Samsung Galaxy Spica android phone. Shutting down the game on my end restores the wireless connection automagicly. My wife can start DDO without the net dropping but if I plug in a wireless network card in my computer and start up the game the connection drops. So it seems like something my computer, and my computer only, does when starting a game makes the wireless connection write a sad note and kill it self but for the life of me I can't figure out what that might be. I could hook her computer up using cat-5 but I would prefer not to do that. Does anyone have any suggestions as to what the problem might be, what I can do to fix it or what I should do to get more data regarding what is happening?

    Read the article

  • Why would my wireless cut in and out every minute or so?

    - by Strilanc
    I've been having problems with my wireless. I moved to a new apartment, and the wireless seems incredibly unreliable. Sometimes it will be stable for hours until, all of a sudden, it starts cutting in and out. I'll get 30-90 seconds of normal behavior, then 5-30 seconds of nothing, then repeat. Sometimes the connection will stop working entirely, until I power-cycle the router. It is extremely, extremely annoying. Surfing the web isn't too bad, assuming you can stand the random 5-30 second waits. But some connections are sensitive enough to timeout, and it certainly makes multiplayer games unplayable. Facts: I confirmed the problem using ping google.com -t. I get normal traffic, interspersed with bursts of "Request timed out.". I've never had this problem before with this laptop. I didn't bring my own router or modem to the apartment. I'm using what the old tenant had. Hooking directly to the modem via an ethernet cable results in a stable connection. Temporarily cutting power to the router sometimes fixes the problem. Sometimes it doesn't. I reset the router, but the problem remained. Apparently the previous tenant had issues with the internet, but I don't know what they were specifically. The router is a D-Link DIR-615, and their tech support is useless.

    Read the article

  • Setting Up My Home Network

    - by Skizz
    I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

    Read the article

  • Resolving loss of internet bandwidth in home network

    - by Caspar
    Recently, I've decided to connect my laptop at home to my modem/router through Ethernet cables built into my apartment. As these built-in Ethernet cables are usable via plugs built into the walls (called powerline adapters), I use some additional cabling (STP CAT6 cables) from my laptop/router to the plugs. In addition, I don't know any technical details about these built-in cables (as they're not visible), only the maximal bandwidth (1 GBit = Cat6?) that they're supporting. The built-in cables are Cat. 5e Ethernet cables. The problem is now that when I set up the connection, I cannot use the full bandwidth that my internet connection is actually offering (100 Mbit/s), only about 85 Mbit/s between 85 - 88 Mbit/s, despite the fact that all cables involved should support the maximal bandwidth. I know from other tests with one of the Ethernet cables in use that I can use almost 99 Mbit/s when I connect my laptop directly to the router/modem using only this one cable. In addition, it is very unlikely that the length of the resulting cable connection from my laptop to my router involving the built-in cables exceeds 100 m. So, what possible reasons for this loss of bandwidth exist? And how I can fix this issue? I hope this might help resolve the issue: The built-in cables appear to be Cat. 5e Ethernet cables. So, is there any problem when I connect Cat6 Ethernet cables directly to Cat5e Ethernet cables via the plugs?

    Read the article

  • Why does my DD-WRT not accept SSH connections from my laptop?

    - by Vlad Seghete
    So, here is my system: I have a 2Wire AT&T modem/router which I use for wireless and a Buffalo router flashed with DD-WRT which is physically attached to the 2Wire and set in the DMZ. I set everything up on the DD-WRT to be able to connect to it using ssh and also so that it forwards ssh requests on a different port to one of the servers behind it. Now, when I am physically connected to the DD-WRT all this works great and as I would want it to. I ssh into the two different ports using the WAN IP of my network, and I get where I expect to land. If, however, I am connected using wi-fi to the 2Wire, the same commands do not work. I do not get an error, simply a timeout. I have trouble understanding this, since the DD-WRT is set in the DMZ and everything should pass to it. To further complicate the problem, I tried connecting to the same IP using my phone (wireless disabled, so really from the WAN) and surprise, it works! If I go back on the local network by enabling the wifi, the ssh connection times out. To make this even stranger, my WAN IP address always responds to pings (meaning in all the above situations). What could be going on here? I know what I should do, completely disable the 2wire as a router and use it strictly as a modem and them use all the routing capabilities of the dd-wrt. It's what I will probably end up doing anyway, but my question remains, because I really want to know what is happening here.

    Read the article

< Previous Page | 18 19 20 21 22 23 24 25 26 27 28 29  | Next Page >