Search Results

Search found 1167 results on 47 pages for 'modem'.

Page 23/47 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Broad Band LAN connection through existing 6 wire phone line ( no phone connected )

  - by Paul Taylor

  I have an (up to but never achieved ) 10 mb broadband signal coming into my house along the telephone line. The modem then connects the broadband signal via a LAN connection and Wi-Fi signal to my computers and iPad. My workshop desk is 54 yards (approx. 50m) downhill from the modem (part of a separate building) – too far to give a good direct signal. The inside corner of the workshop (by a window) receives a weak signal. I have a disconnected telephone cable consisting of 6 wires going from the house to the workshop. The telephone is no longer used in the workshop - we use our mobile number for business calls. A broad band signal using the cable would not have to share with a phone. What would be the most economic price/efficient way to get the broadband signal to the workshop? I am writing in hope that since the telephone didn't need the six wires, an Ethernet connection might be similar and not need all the eight wires for a LAN connection. In theory could use the telephone wire to pull an Ethernet cable trough the underground pipe but I doubt if the cable would survive the strain. The broad band connection in the workshop does not have to have network facility. My skill level is high enough to do house wiring, plumbing and gas fitting; so given any sound advice and a wiring diagram or instructions I can probably work out the rest myself.

  Read the article

• Why do I need a managed switch and which one should I buy?

  - by ascanio1

  I bought a 2nd router and I want both routers to have direct WAN access to the modem. One of the 2 routers directs VOIP traffic to a telephone line port. This VOIP service is provided by the cable carrier which also leases the modem & the router. The cable company technician told me that this VOIP line uses IPv6 addressing and therefore I must employ an IPv6 capable/compliant Giga Hub/Switch or my telephone line won't work anymore. Pls advise me (brand/model) an IPv6 compliant, 2 port, switch to purchase. Pls educate me: By reading this forum I thought that hubs broadcast traffic to all ports, regardless of which input/output is being used and so, theoretically, they have nothing to do with IP. Correct? Same story for unmanaged switches, where the only difference is that these latter devices route traffic only to those ports which are detected to be in use. Correct? I also understood that unmanaged switches route traffic simply by detecting hardware use and not by selecting specific IP traffic. Correct? Finally, there are managed switches which DO select traffic based on IP and, therefore, only these managed switches are involved with IPv6... Why would my cable company explicitly tell me, over and over, that I must use an IPv6 compliant switch? Why would they need a managed switch instead of an unmanaged one? Thanks in advance for helping me understand!

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Different external ip addresses from different sites

  - by user630286

  My router is ClearOS 6(Centos 6). In my router, I have two external (internet) network connections from two ISP's. The primary connection is eth2 connected to a cable modem and the second one is ppp0 connected to a dsl modem. I have assigned eth2 as the primary connection (with a high metric value). In fact this is done through clearos's multiwan web interface. I have a test in my Nagios to monitor whether the primary connection. This connection is done based on the result of curl ifconfig.me But it seems that ifconfig.me is always giving the ip address of my secondary connection. I tested it through a browser. Yes ifconfig.me gives the secondary internet's(ppp0) ip address. But whatismyipaddress.[com|org] give my primary ip address (eth2). I checked the default route on the router through ip route list 0/0 which also shows the primary connection (eth2) as the default route. The traceroute www.google.com and traceroute ifconfig.me both seems to trace through the primary connection (eth2). As our secondary internet connection has only got a limited download, I don't want to end up having to pay a large sum at the end of the month. Has somebody got an idea why the ifconfig.me shows my secondary address? What is the best way to ensure that my router(and thus the lan) use the right internet connection.

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• A very peculiar problem with an old pc and a newer laptop...

  - by user553492

  I got my old pc ( 248mb ram , 80 GB ) repaired and the tech people put XP in it .My newer laptop has UBUNTU 10.04 .now I only have one cable and one usb cord .So I connected my modem (with only one CAT5 port and 4 usb ports ) to laptop with CAT5 cable .Th internet is working fine . I also wanted to use net on older pc so I installed the usb drivers for win and it worked. But I got fed up of win xp and made a separate partition for FreeBSD which I planned to install .During the install I screwd up sumthing and now freebsd starts with a boot option with a ? mark in place of win xp .If I click on that it gives me a "NTLDR missing " msg. I tried connecting CAT5 cable between old and new pc and tried connecting my laptop with USB cable but nothing happend and then I realozed the modem doesnt have a WORKING usb driver for LINUX :( .FCUK ! .Freebsd doesnt` even detect the LAN cable if I use it for old pc . So basically I have a old pc that has FREEBSD which I can olny start and stare at the blank terminal console but works perfectly otherwise .FREEBSD was supposed to detect the LAN cable ??.And I have a laptop that has LINUX which only works if I connect it with a CAT5 cable .wtf . So what can I do with my old pc ??? any local server (if possible :( ) or some such thing ? or can u suggest any use .Im 18 and im into learning programming , coding .So I can practice it .Thankx !

  Read the article

• pfsense 2.0 traffic priority - set full priority for single host

  - by Waxhead

  I have a network with several computers all on the same network and since I have very limited bandwidth I would like to prioritize traffic almost like a CPU scheduler prioritize processes. Example: Computer A: Used for webstuff: YouTube, downloads, news, emails etc. Computer B: Transferring files over HTTP Computer C: Transferring files over ftp, rsync whatever What I would like to do is to give A up to for example 90% of the available bandwidth IF A requires it. The leftovers (10%) is divided between B and C (5% each if both is busy) If A is not utilizing all bandwidth then of course B and C should share the full bandwidth (50% each as long as both are maxing out their bandwidth). All computers are on the same network (192.168.1.0 - 192.168.1-10 for example). Appreciate if anyone could shed some light on how I should set up my network to achieve this. To be honest I actually need a step by step guide on how I should set this up. Network setup: (ADSL modem configured in bridge mode (1500kbps/300kbps)) [ADSL modem (bridge)]<-[pfsense2.0]<-[switch]<-[Computer A,B,C...etc]

  Read the article

• Two internet connections at once in Windows 7

  - by webmasters

  I have a 3G wireless modem and I have a LAN - Right now they are both connected. I need a way to choose which applications will use the 3G connection and which applications will use the LAN. My Operating System is windows 7. How can I do this? Any ideas? Here is a route print: - the 3G modem's IP is 10.81.132.96 Lets say, for example, map google.com to using the 3G internet connection. IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.2.1 192.168.2.102 20 0.0.0.0 0.0.0.0 10.81.132.97 10.81.132.111 286 10.81.132.96 255.255.255.224 On-link 10.81.132.111 286 10.81.132.111 255.255.255.255 On-link 10.81.132.111 286 10.81.132.127 255.255.255.255 On-link 10.81.132.111 286 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.2.0 255.255.255.0 On-link 192.168.2.102 276 192.168.2.102 255.255.255.255 On-link 192.168.2.102 276 192.168.2.255 255.255.255.255 On-link 192.168.2.102 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.2.102 276 224.0.0.0 240.0.0.0 On-link 10.81.132.111 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.2.102 276 255.255.255.255 255.255.255.255 On-link 10.81.132.111 286 ===========================================================================

  Read the article

• Troubleshooting my internet connection

  - by Simon Verbeke

  While I was out of the house, my father rearranged the network cables a bit. I don't know what he has done exactly - He says nothing more then pulling and untangling. When I came back home, my internet connection changed its IP from 192.168.0.205 to 169.254.197.233. The speed changed from 1Gbps to 10Mbps. It has also been at 100Mbps for a while. My subnetmask changed from 255.255.255.0 to 255.255.0.0. The standard gateway changed from 192.168.0.1 to no standard gateway. My DNS servers remain the same. I have checked the lights of the UTP ports, and it looks like it's only sending a heartbeat every few seconds. A sketch of the (relevant part of) the network: My PC ----- extender ----- modem ^ ^ ^ Wired | Wired | This thing connects two cables to each other All the cabling is gigabit, my network card is a Realtek RTL8168C(P)/8111(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20). THe modem is a CBN SVG6540E I have no idea what is going on here and I don't know how to find out either. Any help is welcome! If you need any more info, please ask.

  Read the article

• Receiving and processing SMS messages through a script?

  - by ShankarG

  I am attempting to setup a system to receive and process SMS messages automatically. The system is intended for use in a context (an unfunded migrant workers' union in India) where both finances and sysadmin skills are extremely constrained (I would be the only person, in the near future, who would be administering the system). The intention is to make some functions - registration of members, generation of ID cards, communication of alerts and other information - easier. However, for receiving and sending SMS, I have not been able to find any email to SMS or other kind of gateway that functions in India. Perhaps there is one (edit: apparently Clickatell does have an India service, but the prices appear astronomical). If not, can one rely on a USB mobile modem (such as those provided by many mobile providers in India)? It seems like, with utilities such as gammu or bitpim, SMS operations on such a modem could be scripted. Is this actually feasible, though? Thanks in advance for your thoughts and suggestions. edit: Original first question removed since the two questions had little to do with each other. The original first question has been asked separately here

  Read the article

• Linux IPTables / routing issue

  - by Jon

  Hi all, EDIT 1/3/10 22:00 GMT - rewrote some of it after further investigation It has been a while since I looked at IPtables and I seem to be worse than before as I can not seem to get my webserver online. Below is my firewall rules on the gateway server that is running the dhcp server accessing the net. The webserver is inside my network on a static IP (192.168.0.98, default port). When I use Nmap or GRC.com I see that port 80 is open on the gateway server but when I browse to it, (via public URL. http://www.houseofhawkins.com) it always fails with a connection error, (nmap cannot connect and figure out what the web server is either). I can nmap the webserver and browse to it just fine via same IP inside my network. I believe it is my IPTable rules that are not letting it through. Internally I can route all my requests. Each machine can browse to the website and traffic works just fine. I can MSTSC / ssh to all the webservers internally and they inturn can connect to the web. IPTABLE: *EDIT - Added new firewall rules 2/3/10 * #!/bin/sh iptables="/sbin/iptables" modprobe="/sbin/modprobe" depmod="/sbin/depmod" EXTIF="eth2" INTIF="eth1" load () { $depmod -a $modprobe ip_tables $modprobe ip_conntrack $modprobe ip_conntrack_ftp $modprobe ip_conntrack_irc $modprobe iptable_nat $modprobe ip_nat_ftp echo "enable forwarding.." echo "1" > /proc/sys/net/ipv4/ip_forward echo "enable dynamic addr" echo "1" > /proc/sys/net/ipv4/ip_dynaddr # start firewall # default policies $iptables -P INPUT DROP $iptables -F INPUT $iptables -P OUTPUT DROP $iptables -F OUTPUT $iptables -P FORWARD DROP $iptables -F FORWARD $iptables -t nat -F #echo " Opening loopback interface for socket based services." $iptables -A INPUT -i lo -j ACCEPT $iptables -A OUTPUT -o lo -j ACCEPT #echo " Allow all connections OUT and only existing and related ones IN" $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A OUTPUT -o $EXTIF -j ACCEPT $iptables -A OUTPUT -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $EXTIF -o $INTIF -m state --state ESTABLISHED,RELATED -j ACCEPT $iptables -A FORWARD -i $INTIF -o $EXTIF -j ACCEPT $iptables -A FORWARD -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A INPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " $iptables -A OUTPUT -j LOG --log-level 7 --log-prefix "Dropped by firewall: " #echo " Enabling SNAT (MASQUERADE) functionality on $EXTIF" $iptables -t nat -A POSTROUTING -o $EXTIF -j MASQUERADE $iptables -A INPUT -i $INTIF -j ACCEPT $iptables -A OUTPUT -o $INTIF -j ACCEPT #echo " Allowing packets with ICMP data (i.e. ping)." $iptables -A INPUT -p icmp -j ACCEPT $iptables -A OUTPUT -p icmp -j ACCEPT $iptables -A INPUT -p udp -i $INTIF --dport 67 -m state --state NEW -j ACCEPT #echo " Port 137 is for NetBIOS." $iptables -A INPUT -i $INTIF -p udp --dport 137 -j ACCEPT $iptables -A OUTPUT -o $INTIF -p udp --dport 137 -j ACCEPT #echo " Opening port 53 for DNS queries." $iptables -A INPUT -p udp -i $EXTIF --sport 53 -j ACCEPT #echo " opening Apache webserver" $iptables -A PREROUTING -t nat -i $EXTIF -p tcp --dport 80 -j DNAT --to 192.168.0.96:80 $iptables -A FORWARD -p tcp -m state --state NEW -d 192.168.0.96 --dport 80 -j ACCEPT } flush () { echo "flushing rules..." $iptables -P FORWARD ACCEPT $iptables -F INPUT $iptables -P INPUT ACCEPT echo "rules flushed" } case "$1" in start|restart) flush load ;; stop) flush ;; *) echo "usage: start|stop|restart." ;; esac exit 0 route info: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 5e0412a6.bb.sky * 255.255.255.255 UH 0 0 0 eth2 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 default 5e0412a6.bb.sky 0.0.0.0 UG 100 0 0 eth2 ifconfig: eth1 Link encap:Ethernet HWaddr 00:22:b0:cf:4a:1c inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::222:b0ff:fecf:4a1c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:79023 errors:0 dropped:0 overruns:0 frame:0 TX packets:57786 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:11580918 (11.5 MB) TX bytes:22872030 (22.8 MB) Interrupt:17 Base address:0x2b00 eth2 Link encap:Ethernet HWaddr 00:0c:f1:7c:45:5b inet addr:94.4.18.166 Bcast:94.4.18.166 Mask:255.255.255.255 inet6 addr: fe80::20c:f1ff:fe7c:455b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:57038 errors:0 dropped:0 overruns:0 frame:0 TX packets:34532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:21631721 (21.6 MB) TX bytes:7685444 (7.6 MB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overruns:0 frame:0 TX packets:16 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1517 (1.5 KB) TX bytes:1517 (1.5 KB) EDIT OK so as requested I will try and expand on my infrastructure: I previously had it setup with a Sky broadband modem router that did the DHCP and I used its web interface to port forward the web across to the web server. The network looked something like this: I have now replaced the sky modem with a dlink modem which gives the IP to the gateway server that now does the DHCP. It looks like: The internet connection is a standard broadband connection with a dynamic IP, (use zoneedit.com to keep it updated). I have tried it on each of the webservers(one Ubuntu Apache server and one WS2008 IIS7). I think there must also be an issue with my IPTable rules as it can route to my win7 box which has the default IIS7 page and that would not display when I forwarded all port 80 to it. I would be really grateful for any and all help with this. Thanks Jon

  Read the article

• Poor home office network performance and cannot figure out where the issue is

  - by Jeff Willener

  This is the most bizarre issue. I have worked with small to mid size networks for quite a long time and can say I'm comfortable connecting hardware. Where you will start to lose me is with managed switches and firewalls. To start, let me describe my network (sigh, shouldn't but I MUST solve this). 1) Comcast Cable Internet 2) Motorola SURFboard eXtreme Cable Modem. a) Model: SB6120 b) DOCSIS 3.0 and 2.0 support c) IPv4 and IPv6 support 3-A) Cisco Small Business RV220W Wireless N Firewall a) Latest firmware b) Model: RV220W-A-K9-NA c) WAN Port to Modem (2) d) vlan 1: work e) vlan 2: everything else. 3-B) D-Link DIR-615 Draft 802.11 N Wireless Router a) Latest firmware b) WAN Port to Modem (2) 4) Servers connected directly to firewall a) If firewall 3-A, then vlan 1 b) CAT5e patch cables c) Dell PowerEdge 1400SC w/ 10/100 integrated NIC (Domain Controller, DNS, former DHCP) d) Dell PowerEdge 400SC w/ 10/100/1000 integrated NIC (VMWare Server) 4) Linksys EZXS88W unmanaged Workgroup 10/100 Switch a) If firewall 3-A, then vlan 2 b) 25' CAT5e patch cable to firewall (3-A or 3-B) c) Connects xBox 360, Blu-Ray player, PC at TV 5) Office equipment connected directly to firewall a) If firewall 3-A, then vlan 1 b) ~80' CAT6 or CAT5e patch cable to firewall (3-A or 3-B) c) Connects 1) Dell Latitude laptop 10/100/1000 2) Dell Inspiron laptop 10/100 3) Dell Workstation 10/100/1000 (Pristine host, VMWare Workstation 7.x with many bridged VM's) 4) Brother Laser Printer 10/100 5) Epson All-In-One Workforce 310 10/100 5-A) NetGear FS116 unmanaged 10/100 switch a) I've had this switch for a long time and never had issues. 5-B) NetGear GS108 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-C) Linksys SE2500 unmanaged 10/100/1000 switch a) Bought new for this issue and returned. 5-D) TP-Link TL-SG10008D unmanaged 10/100/1000 a) Bought new for this issue and still have. 6) VLan 1 Wireless Connections (on same subnet if 3-B) a) Any of those at 5c b) HP Laptop 7) VLan 2 Wireless Connection (on same subnet if 3-B) a) IPad, IPod b) Compaq Laptop c) Epson Wireless Printer Shew, without hosting a diagram I hope that paints a good picture. The Issue The breakdown here is at item 5. No matter what I do I cannot have a switch at 5 and have to run everything wireless regardless of router. Issues related to using a switch (point 5 above) SpeedTest is good. Poor throughput to other devices if can communicate at all. Usually cannot ping other devices even on the same switch although, when able, ping times are good. Eventual lose of connectivity and can "sometimes" be restored by unplugging everything for several days, not minutes or hours but we're talking a week if at all. Directly connect to computer gives good internet connection however throughput to other devices connected to firewall is at best horrible. Yet printing doesn't seem to be an issue as long as they are connected via wireless. I have to force the RV220W to 1000Mb on the respective port if using a Gig Switch Issues related to using wireless in place of a switch (point 5 above) Poor throughput to other devices if can communicate. SpeedTest is good. Bottom line Internet speeds are awesome. By the way, Comcast went WAY above and beyond to make sure it was not them. They rewired EVERYTHING which did solve internet drops. Computer to computer connections are garbage Cannot get switch at 5 to work, yet other at 4 has never had an issue. Direct connection, bypass switch, is good for DHCP and internet. DNS must be on server, not firewall. Cisco insists its my switches but as you can see I have used four and two different cables with the same result. My gut feeling is something is happening with routing. But I'm not smart enough to know that answer. I run a lot of VM's at 5-c-3, could that cause it? What's different compared to my previous house is I have introduced Gigabit hardware (firewall/switches/computers). Some of my computers might have IPv6 turned on if I haven't turned it off already. I'm truly at a loss and hope anyone has some crazy idea how to solve this. Bottom line, I need a switch in my office behind the firewall. I've changed everything. The real crux is I will find a working solution and, again, after days it will stop working. So this means I cannot isolate if its a computer since I have to use them. Oh and a solution is not throwing more money at this. I'm well into $1k already. Yah, lame.

  Read the article

• DNS problems on CentOS fresh install

  - by Rick Koshi

  I'm having some DNS issues on a new box I'm installing with CentOS 6.2. I am able to look up names using nslookup, dig, or host. I am able to ping machines by name or by IP address. However, when I try other tools, such as ssh, wget, or yum, they are unable to resolve names. For example: # wget http://www.google.com --2012-03-08 14:48:06-- http://www.google.com/ Resolving www.google.com... failed: Name or service not known. wget: unable to resolve host address `www.google.com' # ssh www.google.com ssh: Could not resolve hostname www.google.com: Name or service not known # ping -c 1 www.google.com PING www.l.google.com (74.125.113.106) 56(84) bytes of data. 64 bytes from vw-in-f106.1e100.net (74.125.113.106): icmp_seq=1 ttl=46 time=43.6 ms --- www.l.google.com ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 59ms rtt min/avg/max/mdev = 43.665/43.665/43.665/0.000 ms # host www.google.com www.google.com is an alias for www.l.google.com. www.l.google.com has address 74.125.113.99 www.l.google.com has address 74.125.113.103 www.l.google.com has address 74.125.113.104 www.l.google.com has address 74.125.113.105 www.l.google.com has address 74.125.113.106 www.l.google.com has address 74.125.113.147 My /etc/nsswitch.conf file is the default, including this (standard) line: hosts: files dns /etc/resolv.conf is as set up by DHCP: ; generated by /sbin/dhclient-script nameserver 192.168.1.254 192.168.1.254 is a working DNS server (my DSL modem, working for years with other machines) Anyone know why ping would work, but ssh/wget would fail? Per NcA's suggestion, I tried changing /etc/resolv.conf to point to 8.8.8.8. Oddly enough, this does make it work. Obviously, my DSL modem is responding to DNS requests in some way that some parts of Linux's resolution system don't like. Looking at the tcpdump, I am unable to see what the difference is. Certainly, both servers are sending the same addresses. Here's the output from tcpdump -nn -X with the server set to the DNS server on the DSL modem. It's clearly replying with the correct addresses, but ssh/wget don't seem happy with it for some reason: 15:53:52.133580 IP 192.168.1.254.53 > 192.168.1.2.54836: 33157 7/0/0 CNAME www.l.google.com., A 74.125.115.105, A 74.125.115.106, A 74.125.115.147, A 74.125.115.99, A 74.125.115.103, A 74.125.115.104 (148) 0x0000: 4500 00b0 e33a 0000 ff11 53b1 c0a8 01fe E....:....S..... 0x0010: c0a8 0102 0035 d634 009c 7528 8185 8180 .....5.4..u(.... 0x0020: 0001 0007 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 0001 0001 c00c 0005 gle.com......... 0x0040: 0001 0007 acd0 0008 0377 7777 016c c010 .........www.l.. 0x0050: c02c 0001 0001 0000 0001 0004 4a7d 7369 .,..........J}si 0x0060: c02c 0001 0001 0000 0001 0004 4a7d 736a .,..........J}sj 0x0070: c02c 0001 0001 0000 0001 0004 4a7d 7393 .,..........J}s. 0x0080: c02c 0001 0001 0000 0001 0004 4a7d 7363 .,..........J}sc 0x0090: c02c 0001 0001 0000 0001 0004 4a7d 7367 .,..........J}sg 0x00a0: c02c 0001 0001 0000 0001 0004 4a7d 7368 .,..........J}sh 15:53:52.135669 IP 192.168.1.254.53 > 192.168.1.2.54836: 65062- 0/0/0 (32) 0x0000: 4500 003c e33b 0000 ff11 5424 c0a8 01fe E..<.;....T$.... 0x0010: c0a8 0102 0035 d634 0028 98f9 fe26 8000 .....5.4.(...&.. 0x0020: 0001 0000 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 001c 0001 gle.com..... I'm not enough of an expert to know if this is malformed in some way, but ping seems to do the right thing with it. For comparison, here's the same thing when querying 8.8.8.8: 15:57:27.990270 IP 8.8.8.8.53 > 192.168.1.2.49028: 59114 7/0/0 CNAME www.l.google.com., A 74.125.113.105, A 74.125.113.103, A 74.125.113.106, A 74.125.113.147, A 74.125.113.104, A 74.125.113.99 (148) 0x0000: 4500 00b0 5530 0000 2f11 6453 0808 0808 E...U0../.dS.... 0x0010: c0a8 0102 0035 bf84 009c 39f8 e6ea 8180 .....5....9..... 0x0020: 0001 0007 0000 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 0001 0001 c00c 0005 gle.com......... 0x0040: 0001 0001 516a 0008 0377 7777 016c c010 ....Qj...www.l.. 0x0050: c02c 0001 0001 0000 0116 0004 4a7d 7169 .,..........J}qi 0x0060: c02c 0001 0001 0000 0116 0004 4a7d 7167 .,..........J}qg 0x0070: c02c 0001 0001 0000 0116 0004 4a7d 716a .,..........J}qj 0x0080: c02c 0001 0001 0000 0116 0004 4a7d 7193 .,..........J}q. 0x0090: c02c 0001 0001 0000 0116 0004 4a7d 7168 .,..........J}qh 0x00a0: c02c 0001 0001 0000 0116 0004 4a7d 7163 .,..........J}qc 15:57:28.018909 IP 8.8.8.8.53 > 192.168.1.2.49028: 31984 1/1/0 CNAME www.l.google.com. (102) 0x0000: 4500 0082 7b1b 0000 2f11 3e96 0808 0808 E...{.../.>..... 0x0010: c0a8 0102 0035 bf84 006e c67e 7cf0 8180 .....5...n.~|... 0x0020: 0001 0001 0001 0000 0377 7777 0667 6f6f .........www.goo 0x0030: 676c 6503 636f 6d00 001c 0001 c00c 0005 gle.com......... 0x0040: 0001 0001 517f 0008 0377 7777 016c c010 ....Q....www.l.. 0x0050: c030 0006 0001 0000 0258 0026 036e 7334 .0.......X.&.ns4 0x0060: c010 0964 6e73 2d61 646d 696e c010 0016 ...dns-admin.... 0x0070: 91f3 0000 0384 0000 0384 0000 0708 0000 ................ 0x0080: 003c .< I still don't know why the server's reply is adequate for ping but not for ssh/wget. If anyone has ideas, I'd be happy to hear them. For now, though, I can either refer to an outside DNS server or set up my own server on the new box. It's a workaround that seems like it should be unnecessary, but will allow me to proceed.

  Read the article

• General website publishing questions involving domain forwarding issue

  - by Gorgeousyousuf

  Even though I have been having a certain level of knowledge and experience about web development I have never interested in obtaining a domain and publishing a website from my own server. Since today I have been struggling with getting my own domain and configuring it utilizing web sources. I started with learning the outline of web publishing process including web server installation, deploying a website for testing purpose,router port forwarding, getting a domain and forwarding domain to my router which will also forward http requests to my web server I am confused about some parts and so far could not get the web site accessed from outside of the network. All I try to do is just for learning purpose so I do not pay much attention to security issues for now. I have Server 2008 and IIS 7.5 installed. I use a laptop and have access to the modem over wireless and my modem is Zoom x6 5590. Well I will continue explaining what I have done so far and what I think will be after each action I did, I have successfully had access to my website on any local computer entering the internal ip address and port pair of the host machine in a browser. Next, I forwarded port 80 of my host machine creating a virtual server like 10.0.0.x(internal ip(static) of the host) - tcp - start port : 80 - end port : 80 in router options. Now I suppose every request that will come to the public Ip on port 80 will be forwarded to my host machine(10.0.0.x) over port 80. So If everyhing went as desired, the website listening on port 80 will accept the request and process the issue and finally respond bla bla bla... I suppose to access my website from outside of the network by entering http://MyPublicIp:80 in a browser but I couldn't accomplish this task by now despite using godady's domain forwarding tool,I see a small view of my website when I click the "preview" button that checks whether the address(http://publicip/Index.aspx) I entered where my domain will be forwarded is available or not. I am sure that configuring domain does not play a role in solving such a problem since using public ip and port matching does not help. So here is the first question, What is the fact that I face this problem? After that, I have couple of question regarding domain forwarding using godaddy tool. Can I forward my domain to a any port for example port 8080 other than default http port 80? Additionally, can I use a sub-domain to forward to a different port of the host? What I want to design is if the client enters www.mydomain.com, website1 will respond over a specified port and after when a client enters info.mydomain.com, another website which listens on different port will respond. I tried to add a sub-domain and forward it to a address like http://www.mydomain.com:8080/Index.aspx with no success. Can I really do that? Finally, what if I have a ftp site listening on the default port 21 and I create a domain like ftp.mydomain.com that will forward to that ftp site address. Is it possible to use sub-domains for ftp site access? I know I am more than confused but no matter whatever and however you reply to me, you will help me have a more clear view on this subject. Thank you very much from now.

  Read the article

• I got my z-5 Logitech speakers to work, but whenever I restart, I have to reconfigure them

  - by The Bill

  This is the content of my alsa-base.conf file (for some reason, the entries preceded by # are bolded--anyway): autoloader aliases install sound-slot-0 /sbin/modprobe snd-card-0 install sound-slot-1 /sbin/modprobe snd-card-1 install sound-slot-2 /sbin/modprobe snd-card-2 install sound-slot-3 /sbin/modprobe snd-card-3 install sound-slot-4 /sbin/modprobe snd-card-4 install sound-slot-5 /sbin/modprobe snd-card-5 install sound-slot-6 /sbin/modprobe snd-card-6 install sound-slot-7 /sbin/modprobe snd-card-7 Cause optional modules to be loaded above generic modules install snd /sbin/modprobe --ignore-install snd $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-ioctl32 ; /sbin/modprobe --quiet --use-blacklist snd-seq ; } # Workaround at bug #499695 (reverted in Ubuntu see LP #319505) install snd-pcm /sbin/modprobe --ignore-install snd-pcm $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-pcm-oss ; : ; } install snd-mixer /sbin/modprobe --ignore-install snd-mixer $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-mixer-oss ; : ; } install snd-seq /sbin/modprobe --ignore-install snd-seq $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; /sbin/modprobe --quiet --use-blacklist snd-seq-oss ; : ; } # install snd-rawmidi /sbin/modprobe --ignore-install snd-rawmidi $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq-midi ; : ; } Cause optional modules to be loaded above sound card driver modules install snd-emu10k1 /sbin/modprobe --ignore-install snd-emu10k1 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-emu10k1-synth ; } install snd-via82xx /sbin/modprobe --ignore-install snd-via82xx $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist snd-seq ; } Load saa7134-alsa instead of saa7134 (which gets dragged in by it anyway) install saa7134 /sbin/modprobe --ignore-install saa7134 $CMDLINE_OPTS && { /sbin/modprobe --quiet --use-blacklist saa7134-alsa ; : ; } Prevent abnormal drivers from grabbing index 0 options bt87x index=-2 options cx88_alsa index=-2 options saa7134-alsa index=-2 options snd-atiixp-modem index=-2 options snd-intel8x0m index=-2 options snd-via82xx-modem index=-2 options snd-usb-audio index=-2 options snd-usb-caiaq index=-2 options snd-usb-ua101 index=-2 options snd-usb-us122l index=-2 options snd-usb-usx2y index=-2 alias snd-card-0 snd-usb-audio alias snd-card-1 snd-hda-intel options snd-usb-audio index=0 options snd-hda-intel index=1 Ubuntu #62691, enable MPU for snd-cmipci options snd-cmipci mpu_port=0x330 fm_port=0x388 Keep snd-pcsp from being loaded as first soundcard options snd-pcsp index=-2 options snd-usb-audio index=-2 options snd-usb-audio index=0 alias snd-card-0 snd-usb-audio alias snd-card-1 snd-hda-intel options snd-hda-intel index=1 I deleted a line that said something like "#Keep usb-audio from being loaded as first soundcard" and that made the speakers work for the first time (before this, they never showed up). I also added the last four lines. Anyway, what can I add to this so that I don't have to reconfigure them each time I restart? Currently, I have to open Sound Settings, then under the hardware tab, select Analog Stereo Output, and then unplug my USB speakers and plug them back in. This makes them pop up so that I can see them. Otherwise, it will not show my Z-5 speakers as a device that can be configured.

  Read the article

• How to find an embedded platform?

  - by gmagana

  I am new to the locating hardware side of embedded programming and so after being completely overwhelmed with all the choices out there (pc104, custom boards, a zillion option for each board, volume discounts, devel kits, ahhh!!) I am asking here for some direction. Basically, I must find a new motherboard and (most likely) re-implement the program logic. Rewriting this in C/C++/Java/C#/Pascal/BASIC is not a problem for me. so my real problem is finding the hardware. This motherboard will have several other devices attached to it. Here is a summary of what I need to do: Required: 2 RS232 serial ports (one used all the time for primary UI, the second one not continuous) 1 modem (9600+ baud ok) [Modem will be in simultaneous use with only one of the serial port devices, so interrupt sharing with one serial port is OK, but not both] Minimum permanent/long term storage: Whatever O/S requires + 1 MB (executable) + 512 KB (Data files) RAM: Minimal, whatever the O/S requires plus maybe 1MB for executable. Nice to have: USB port(s) Ethernet network port Wireless network Implementation languages (any O/S I will adapt to): First choice Java/C# (Mono ok) Second choice is C/Pascal Third is BASIC Ok, given all this, I am having a lot of trouble finding hardware that will support this that is low in cost. Every manufacturer site I visit has a lot of options, and it's difficult to see if their offering will even satisfy my must-have requirements (for example they sometimes list 3 "serial ports", but it appears that only one of the three is RS232, for example, and don't mention what the other two are). The #1 constraint is cost, #2 is size. Can anyone help me with this? This little task has left me thinking I should have gone for EE and not CS :-). EDIT: A bit of background: This is a system currently in production, but the original programmer passed away, and the current hardware manufacturer cannot find hardware to run the (currently) DOS system, so I need to reimplement this in a modern platform. I can only change the programming and the motherboard hardware.

  Read the article

• SQL Error (2003): Can't connect to MySQL server on 'X.X.X.X.' (10051) - What does this error mean?

  - by BeeS

  I get following error when i try to connect via "HeidiSQL" to my database server (local network) SQL Error (2003): Can't connect to MySQL server on 'X.X.X.X.' (10051) SSH Connection via Putty works fine. I checked the my.cnf file on the server (Ubuntu), but settings like bind_address are correct. Is it possible that my wireless modem (SpeedTouch) makes this trouble? (Because my provider changed the download speed) !? Thank you very much for your help!

  Read the article

• What are the pay as you go (prepay) options in the USA for a USB 3G mobile internet dongle?

  - by m3ntat

  I travel between the UK and US a lot, I'm looking for a pay as you go (prepay) USB 3G modem for mobile internet that I can use with my laptop while in the States that is reasonably priced. In the UK with O2 I can buy the usb dongle for £10 then it's £2 for 24hours/500mb whenever I choose to use it, no other costs. Is there anything like this in the USA? http://shop.o2.co.uk/promo/o2mobilebroadband/tab/Pay_and_Go

  Read the article

• Port forwarding - firewall deactivated?

  - by Suma

  In a Port Forwarding guide I have read I should set port forwarding on my ADSL modem and disable its firewall. Until I did both of this, my torrent client was not visible as a server from outside. However, I am unsure what implications disabling firewall has and why it is needed. Can anyone explain this?

  Read the article

• Convert to WAN port

  - by Ramon Marco Navarro

  I have a ADSL2+ Modem/Router. Is it possible to set one out of four of the LAN ports as a WAN port? If yes, how? The brand/model is: Prolink H9200P. I already contacted Prolink about this and the site said to wait for one business day. But I'm still asking here just in case someone could answer faster than Prolink. Thank you.

  Read the article

• Can a DSL splitter be used in place of a micro filter

  - by axk

  I don't want to do the rewiring required to put a splitter at the demarcation point, but we don't have DSL micro filters available here. Can I use two splitters as filters for the modem and the phone? Thanks!

  Read the article

• How to fix network connection dead on startup, but okay after disable/enable?

  - by bill weaver

  on Startup When my system starts up, the internet connection is dead. This causes various problems with startup items such as updates and auto-start programs failing. However, the connection is fine after going into Network and Sharing, Change adapter settings, then disabling and re-enabling the adapter. Any suggestions on why this is happening and how to fix it? System summary: Windows 7, 64 bit, Realtek PCIe GBE Family Controller, Linksys WRT610N router, Sci Atlanta cable modem.

  Read the article

• Problem with wireless router, always stay local

  - by ThisXcell

  Hey, for some reason my wireless router only allows me access to my local network. I've tried to reset the router and I've followed the set-up wizard and I've also done the advanced set-up and nothing is working. Wireless Router 108MBps Wireless Firewall Router WGT624 v2 ================ Modem Motorola - SB5101 Surfboard issued by Atlantic Boardband

  Read the article

• Setting up a wireless connection

  - by shadeMe

  I've got a DLINK router connected to my ADSL modem that forms the hub of my home network. I've two clients - A desktop with an onboard wireless adaptor and a laptop that's outfitted with the same. The former runs Windows 7 x64, the latter Windows XP x86. I'd like to setup a wireless connection between the two that would allow me play games over to and to a lesser extent, transfer and stream data. How would I go about doing it ?

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >