Search Results

Search found 1167 results on 47 pages for 'modem'.

Page 29/47 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

  • Setup Cisco RVS4000 QOS for VOIP

    - by andyknas
    Just switched from dedicated T1's with analog phone lines to cable modem with 10/2 uplink. We're having some VOIP call quality issues on the outgoing side when bandwidth is stressed and I need to setup QOS or a VLAN on our RVS4000 router. Currently all phone traffic (talkswitch device and ip phones) are on it's own d-link PoE switch, and all workstations are on a LinkSys 1GB switch. Both switches are plugged into ports on the RVS4000. I'd like to set it up so that the dlink port has ~512Mbsp dedicated to it for voice at all times. It's my understanding that with a VLAN or QOS I can set this up. I've got QOS setup already with port 5060 to have high priority but it doesn't seem to make a difference.

    Read the article

  • Setup Linksys 3200 remote access

    - by Greg
    I'm trying to setup remote access for my linksys 3200 so that I can configure it through the WAN port. I have turned on remote access, however when I try to connect I get a 404 error. The settings I have are: When I try to access xxx.xxx.xxx.xxx:9999 I just get a 404 error. I have allowed RDP access to a computer behind the router and this works fine on the same IP address. Any idea's on what else I have to do to allow remote management access? UPDATE: I tried changing the port to 80 and it works. Change it back to any other number and it doesn't work. Modem is setup with a DMZ to the router's IP. Why does it only work on port 80? BTW I can't use port 80 because there is a website hosted behind the router.

    Read the article

  • All downloads being interrupted

    - by Jake
    System: Windows 7 Professional 64bit. 8GB RAM, Intel i5-2400 CPU, +300GB free on the hard drive. AVG Internet Security 2012 (enabled & disabled, with firewall enabled and disabled - no effect for either). This computer is less than a year old. Network: This problem is occurring on a single computer on a network with multiple computers. The router is a Motorola Netopia 3347-02 (DSL Modem/Wireless Router combined). The computer is plugged in directly to the modem, other computers are using the wireless successfully. The router has been reset. The only thing odd about the connection between the router and computer is that it is configured to allow RDP through, so it is assigned a static IP by the router and port forwarding is enabled for port 3389. Also, though I doubt it matters, a second wireless router is active behind this router providing a second network that some computers in the area use without issues. Details: All downloads initiated on this specific computer eventually fail, this includes streaming from youtube, specialized downloads (itunes), downloads from websites, FTP downloads, etc. Failure occurs with all browsers, but in chrome this is the process it takes: 1) Download begins normally, 2) At some point between (observed) 7MBs and 229MBs the download stops progressing (at this point, if watching chrome's task manager, you can see the network activity for the downloading tab drop to 0kps), 3) for some time the download sits there still attempting to complete, but will eventually display "123,049,871/0 B, Interrupted" (where the number is whatever it actually got to). The file I am using to test this is a very large .zip file located on a server I control, but the problem seems to occur on any site. The amount downloaded is completely random, and seems to be more time-based than anything (if I start a download immediately after the last one fails, it tends to get further than the last one). Small files can get through for this reason, though they can fail as well. In a test where I simultaneously downloaded the same file via HTTP (chrome) and FTP (windows explorer), both downloads failed at the same instant, though explorer displayed "Connection timed out" several minutes before chrome finally showed the download as interrupted. Other things I have tried based on advice given to people with similar/identical problems: Setting my MTU to 1492 (as described here: http://blog.thecompwiz.com/2011/08/networking-issues.html) Disabling write caching to the hard drive storing the download on an external device successfully transmitted +1GB file from one computer on the same network to this computer disabling indexing in the folder the download was being stored in disabling all security software checked to make sure all drivers were up to date read about 50 accounts with nearly exact descriptions of what I'm experiencing, none of which had a solution given Running Processes: Image Name PID Session Name Session# Mem Usage ========================= ======== ================ =========== ============ System Idle Process 0 Services 0 24 K System 4 Services 0 104,836 K smss.exe 332 Services 0 1,276 K csrss.exe 764 Services 0 5,060 K wininit.exe 820 Services 0 4,748 K csrss.exe 844 Console 1 23,764 K services.exe 876 Services 0 11,856 K lsass.exe 892 Services 0 14,420 K lsm.exe 900 Services 0 7,820 K winlogon.exe 944 Console 1 7,716 K svchost.exe 428 Services 0 12,744 K svchost.exe 796 Services 0 12,240 K svchost.exe 1036 Services 0 22,372 K svchost.exe 1084 Services 0 174,132 K svchost.exe 1112 Services 0 56,144 K svchost.exe 1288 Services 0 18,640 K svchost.exe 1404 Services 0 29,616 K spoolsv.exe 1576 Services 0 25,924 K svchost.exe 1616 Services 0 12,788 K AppleMobileDeviceService. 1728 Services 0 9,796 K avgwdsvc.exe 1820 Services 0 8,268 K mDNSResponder.exe 1844 Services 0 5,832 K w3dbsmgr.exe 1108 Services 0 43,760 K QBCFMonitorService.exe 1336 Services 0 16,408 K svchost.exe 2404 Services 0 28,240 K taskhost.exe 3020 Console 1 12,372 K dwm.exe 2280 Console 1 5,968 K explorer.exe 2964 Console 1 152,476 K WUDFHost.exe 3316 Services 0 6,740 K svchost.exe 3408 Services 0 5,556 K RAVCpl64.exe 3684 Console 1 13,864 K igfxtray.exe 3700 Console 1 7,804 K hkcmd.exe 3772 Console 1 7,868 K igfxpers.exe 3788 Console 1 10,940 K sidebar.exe 3836 Console 1 84,400 K chrome.exe 3964 Console 1 19,640 K pptd40nt.exe 4068 Console 1 5,156 K acrotray.exe 3908 Console 1 14,676 K avgtray.exe 3872 Console 1 9,508 K jusched.exe 4076 Console 1 4,412 K iTunesHelper.exe 1532 Console 1 87,308 K SearchIndexer.exe 3492 Services 0 36,948 K iPodService.exe 4136 Services 0 7,944 K BrccMCtl.exe 4276 Console 1 18,132 K splwow64.exe 4380 Console 1 32,600 K qbupdate.exe 4836 Console 1 24,236 K svchost.exe 4288 Services 0 20,700 K wmpnetwk.exe 3112 Services 0 9,516 K FNPLicensingService.exe 5248 Services 0 5,852 K QBW32.EXE 5508 Console 1 127,068 K QBDBMgrN.exe 5600 Services 0 42,252 K EXCEL.EXE 2512 Console 1 99,100 K LMS.exe 3188 Services 0 5,616 K UNS.exe 1600 Services 0 7,308 K axlbridge.exe 5260 Console 1 5,132 K chrome.exe 5888 Console 1 200,336 K chrome.exe 3536 Console 1 26,076 K chrome.exe 1952 Console 1 20,168 K chrome.exe 4596 Console 1 24,696 K chrome.exe 4292 Console 1 48,096 K chrome.exe 2796 Console 1 23,520 K Acrobat.exe 1240 Console 1 87,252 K 123w.exe 4892 Console 1 22,728 K calc.exe 1700 Console 1 12,636 K chrome.exe 1328 Console 1 28,888 K chrome.exe 3696 Console 1 47,012 K rundll32.exe 6320 Console 1 7,104 K chrome.exe 4928 Console 1 44,248 K AVGIDSAgent.exe 260 Services 0 12,940 K avgfws.exe 6052 Services 0 26,912 K avgnsa.exe 5064 Services 0 2,496 K avgrsa.exe 3088 Services 0 2,200 K avgcsrva.exe 2596 Services 0 380 K avgcsrva.exe 6948 Services 0 408 K StikyNot.exe 452 Console 1 14,772 K chrome.exe 4580 Console 1 28,200 K chrome.exe 4016 Console 1 57,756 K svchost.exe 7140 Services 0 4,500 K chrome.exe 6264 Console 1 56,824 K chrome.exe 7008 Console 1 56,896 K chrome.exe 2224 Console 1 38,032 K taskhost.exe 612 Console 1 7,228 K chrome.exe 6000 Console 1 10,928 K chrome.exe 2568 Console 1 43,052 K chrome.exe 272 Console 1 75,988 K chrome.exe 7328 Console 1 53,240 K PaprPort.exe 7976 Console 1 137,152 K pplinks.exe 7500 Console 1 14,052 K ppscanmg.exe 5744 Console 1 18,996 K taskeng.exe 7388 Console 1 6,308 K SearchProtocolHost.exe 8024 Services 0 8,804 K SearchFilterHost.exe 7232 Services 0 7,848 K chrome.exe 8016 Console 1 37,440 K cmd.exe 7692 Console 1 3,096 K conhost.exe 7516 Console 1 5,872 K tasklist.exe 8160 Console 1 5,772 K WmiPrvSE.exe 7684 Services 0 6,400 K Any help with this would be greatly appreciated, I've been beating my head against a wall over this all day. This computer serves dual purpose as the main company document server and the Owner's work computer, it's fairly important it be fully functional and I cannot figure this out.

    Read the article

  • Isolating VMware virtual machines from the network

    - by jetboy
    I have: VMware Workstation 7 running on a Windows 7 box (with a single NIC), with multiple virtual machines running a range of OSs. The host box is connected to a WRT54G router running Tomato firmware. The router is acting as a wireless bridge to another WRT54G that's wired to my broadband modem. I can access the VMs externally via VNC using VMware's Remote Display. Over time I've had these running: a. Using NAT networking (single IP) with port forwarding on the router and a custom port in VMware for each VM. b. Using bridged networking with static IPs assigned to each VM via MAC address, and port forwarding on the router to each IP running with standard ports. Either way, the host box, and other physical machines on the network are accessible from the VMs. Is there a way to isolate the VMs from the rest of the network, but still maintain internet access and remote VNC to the VMs?

    Read the article

  • Bind DHCP Server to Network Bridge

    - by Luke
    My wireless router died, so I decided to route everything through my server. So I installed a second NIC and a wireless card to be my new network: 1 NIC to the Modem, 1 NIC to the switch, and the Wireless to... Well, wireless. Anyways, I got far enough to get DHCP to work on just ONE adapter when I used Internet Connection Sharing (I couldn't get RRAS set up for the life of me), then I decided to try bridging the wireless and second NIC. Now, the DHCP server won't bind to the bridge, but I can enter manual IP's in my clients and it'll connect to the Internet. I also tried changing my wireless adapter's IP to 192.168.0.2, and to 192.168.1.1 to try to set up a separate scope, but to no avail. Running Windows Server 2003

    Read the article

  • Share Pc' s wifi internet connection to router and spit it out trough it

    - by Maken
    Basicly im trying to share the an internet connection that i receive through wifi from my bestfriend's place to my place and Extend it trough a router for my consoles and other computers in my household i have 1 pc with Wifi /Ethernet , one router "DD-wrt"ed" Schema is like this Internet -----Modem------- (Friend's)Router -----to my PC through Wifi (Ics)---- to Router(2) through lan----- to Computer 1 (over lan or wifi etc...) ------ Computer 2 (over lan or wifi etc...) i want the computer 1 and 2 to have internet from Router(2) if its not clear enough il try to give more details but a little help would be greatly appreciated

    Read the article

  • How can I setup a subnetwork using DDWRT and a 2Wire?

    - by MadBurn
    Ok, I'm having a bit of trouble getting this setup. I'm not really sure what direction I need to be looking in. I am on ATT UVerse and I have to use their horrible 2Wire Modem/Router. But with this router, I have very limited control over my network and my wifi range is too small for my house. But, I have a hardwire ran to my TV which I have hooked into a switch and split the line to my PS3. The problem I'm having, is I don't know how to get the Buffalo DD-WRT setup as a subnetwork so that the PS3 can find my Media Server. Here is a diagram of what I'm trying to accomplish: Blue is ethernet.

    Read the article

  • network timeout how to analyse problem

    - by elhombre
    In the last three month I was experiencing that my internet connection started to get very slow and websites had long time to load. The first thing I made was an ping to www.google.com which showed that I was loosing pakets. Here some of the results: 64 bytes from 74.125.39.103: icmp_seq=2909 ttl=53 time=48.222 ms Request timeout for icmp_seq 2910 Request timeout for icmp_seq 2911 64 bytes from 74.125.39.103: icmp_seq=2912 ttl=53 time=44.372 ms Days later I had to reset my router because it wasn't able to establish a correct network connection. It was after the reset when things worked again for some days. But later the same network timeouts started to happen again. I would like to know how I can analyze the problem to get to the source which is causing this timeouts. Which steps do you take to circle in this Problem? My Network Laptop - Wireless Router modem - ISP EDIT: I am on a Mac OS X 10.6

    Read the article

  • Using airport extreme base station as a wireless G to wireless N bridge

    - by micmcg
    Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

    Read the article

  • DSL connection dropping when starting game

    - by bootoo
    New connection set up last week - have called tech support, signal fine, sending out tech guy tomorrow - however i cant make sense of this using Vista, 2wire connection 6mb ATT conn, wireless, i can browse website, stream video from my PC wirelessly to my xbox, watch Hulu in high res, connection seems fine I load up World of Warcraft, i select Enter World and without fail my 2wire modem 'DSL' light goes red, my internet light goes out, im no longer connected, then after 10 or 15 seconds it works again, but game has kicked me Noticed the same thing on opening or closing Utorrent as well No other phones/devices plugged into the phone jacks in the apartment - why would joining a game cause my DSL to drop? i can only guess it throws a bunch of information to the server when i hit 'enter world' and that causes an issue that shuts my connection down or my router hates me - all help appreciated

    Read the article

  • Question about Remote WAN IP on NetGear FVS336G VPN setup

    - by camilian
    I wanted to be able to have a VPN connection to my home network so I purchased the FVS336G because the reviews said it was easy set up. I am sure it is for someone that knows what needs to be entered it is easy, but I am a little confused. Using the VPN wizard I choose VPN Client as the tunnel connection, enter key, etc... but then I get to the "What is the remote WAN's IP or Internet Name" and "What is the local WAN's IP address or Internet Name" I am lost. I am probably being really dumb, but I am not sure what I need to put in here. Is the remote WAN ip the ip from the outside world to my cable modem? Is the local ip the ip to my FVS336G? Any help would be appreciated.

    Read the article

  • Is this a common/bug on this PPPoE setting for Cisco ASA 5505?

    - by DCAlliances
    We have to change the way the firewall setup due to we've changed the internet provider. The way we setup we have ADSL modem and we have to do a full bridge mode and the firewall configuration has to change from Static IP to Use PPPoE option on Outside interface with PPPoE username and password, CHAP authentication, WAN IP and WAN subnet mask. [See the attachment] It's been working ok with the use of PPPoE option however the issue is that if we un-plug the power cable of the firewall. This "Outside" interface turned to blank - NO WAN IP, PPPoE username and password. So basically, we have to retype this information again. Is this common or a bug? Any ideas? Thanks

    Read the article

  • Connecting together DIR-615 and DIR-655

    - by ra170
    On my DIR-655 my internal network is: 192.168.0.x On my DIR-615 my internal network is: 192.168.1.x They are both connected to my firewall PIX 501 box The PIX itself is connected to the comcast modem. I briefly looked at the menu options on those router and they look similar, however I'm not sure what's the best way to connect those two together so that I can go between those networks. (printing, file browsing, etc.) I'm not sure if I have to do this somehow on those two router or on the PIX itself, or probably on all of them. If anyone has experience with something like that please let me know..

    Read the article

  • Share laptop Wi-Fi with router set up as access point via ethernet cables

    - by obie
    I have an ADSL modem which serves as a wireless router. There's a laptop connected to it through cable. On the other room I have a laptop which is connected through the router wirelessly. Since I have other appliances that need to get connected but are not Wi-Fi capable I have another Wi-Fi router. How can I share the second laptop's Wi-Fi with the second router so that the router can then serve as an access point to give internet to my other appliances through ethernet cables? I want something like this: INTERNETMODEM (WIFI)LAPTOP 1 (WIFI)LAPTOP 2 (WIFI)Router 2 (ETHERNET)DREAMBOX & WDTV What I've tried so far is opened the admin interface of router 2 then set static IP 192.168.100.13 and disabled the DHCP. The DHCP of the main router starts with 192.168.100.1 then I hooked up router 2 with the laptop 2 through Cat5 cable but for some reason it's not working.

    Read the article

  • Linksys WRT54G2 not showing connected PC's in DHCP table

    - by Moose
    For some reason all of a sudden my linksys WRT54G2 no longer shows PC's connected in the DHCP table. It was being touchy then all of a sudden they all just disappeared. It showed 2 of the 4 connected then it showed the other 2 then it only showed 1 and then it was showing none. I seem to be having a connection reset every 30-60 minutes also not sure if that is related to the router going bad or if it is just comcast being it's typical crappy self. I have tried to reset my router and my cable modem and both problems still seem to keep happening(no PC's in table and connection reset every 30-60 mins). Now I know the router doesn't store clients after a router reboot but they normally show up within a matter of minutes for me in the past. Before anyone asks yes all devices on the network are using DHCP and not static. Could this be a sign of the router starting to go bad?

    Read the article

  • Run a pc on battery for 3 days?

    - by Zen 8000k
    I am looking for a low power, low end pc able to run 24/7 without overheating and a way to support it in case of power failure. Power failures can be up to 72 hours. The pc dosen't need a monitor or keyboard. A modem must also be protected in case of power failure. When i say low end, i don't mean crap. The cpu needs to be x86 and have at least 1k cpu in this chart: http://www.cpubenchmark.net/index.php What's the best way to do this?

    Read the article

  • My acer aspire laptop suddenly stopped working, just a blank screen

    - by mazda
    My acer aspire laptop suddenly stopped working while it was connected to my nokia mobile modem through usb. It stopped with power swich staying on and no response to clicking off, no irregular sound, nothing but just a blank screen. I disconnected the power and battery quickly but power switch did not respond at all and even the power indicator didn't turn on again. the display was also gone after disconecting the power and removing battery. It has no response or any sign of power while both battery and power supply are working. What do you think? A completely dead mainboard? Does the MB has any safty board or fuse that could be replaced? Any suggestion will be appreciated, Thank you.

    Read the article

  • Two network cards in one Windows 7 PC

    - by Martin
    Hi, I've upgraded from Vista to Windows 7. On Vista I used to run one network card (Intel 82566DC -2 Gigabit) for my internet which was connected to a Dovado USB mobile broadband router connected to a 3G modem. The IP setup on the card is set on DHCP. The second card (3com Ethernet link) was used to connect to our town's local WUG (wireless user group) and all worked fine. Now the problem I have with Windows 7 is that when I connect to the internet with the (Intel) first card, the internet work fine but as soon as I connect the second card to the wug my internet drops. If I then disconnect the first card (internet one) and try to connect to the wug it works. It seems that the two cards are fighting each other. Is there maybe something I can do to fix the problem? As you probably can gather from this post is that I am not an expert on PC's so please if you do answer do I in simple terms. :) Thanks, Martin

    Read the article

  • Router stopping my python server

    - by drfrev
    This was originally posted in stackoverflow.com but it was suggested I move it here after it was realized it wasn't my code that was wrong. So my problem, very simply, is that I cannot get my computers that are connected to my router to communicate. example: If I ping a wireless computer I get no responce and the Request times out If I ping a computer wired to the modem directly it works fine. When I ping I use the local ip for each case. *if it helps my original post is here: http://stackoverflow.com/questions/12593024/python-cannot-go-over-internet-network/12593361#12593361 And some screen shots of different things are here: http://imgur.com/a/jUZ4G#3 thank you, any help is greatly appreciated. NOTE I am heading off to bed now, so I will respond around 6:00 AM EST if anyone posts some help

    Read the article

  • How do I stop apps trying to use a dial-up connection?

    - by ProfKaos
    Every now and again, I might have to use a dial-up internet connection via another tethered phone, i.e. Bluetooth connection to the GPRS modem. Now I am back on 'ops normal', i.e. using a shared internet connection on my own phone, or on my 3G stick, but some apps, especially IE9, keep popping up a 'dialup connection' dialogue, which I cannot dismiss enough times ever, to make to stay away. How can I tell these idiot applications that I no longer need a dial-up connection?

    Read the article

  • Acer Aspire 7739G-6647 won't connect to the internet

    - by Nux
    Acer Aspire 7739G-6647, it belongs to a family member. I reinstalled the chipset, LAN drivers, ethernet controllers, etc. I'm positive it's not my router or modem or anything like that. I have other laptops running on the network, this one just has some strange issue. For some reason, it's saying "Work Offline" is enabled when I open Windows Media Player, and the PC seems to be connected to the network, but on the graphic in networking, it doesn't show the connection between the network and the internet. Could anyone try to state any possible reason for this issue? Any help is appreciated.

    Read the article

  • Windows 8 Pro Remote Desktop issue

    - by Mike C.
    I have a weird issue here. I'm running Windows 8 Pro. The client computer is also running Windows 8 Pro. Remote Desktop works when I'm in the same network. I tried connecting using my external IP Address and my DynDNS account, neither works. I disabled Windows Firewall and setup DMZ for my computer on the router, still can't get remote desktop to work. I verified www.canyouseeme.org, port 3389 is open, which is obvious since I'm running DMZ! My ISP, Bell Canada (modem/router: Sagemcom F@st 2864), blocks port 80 and 25, but I don't need those for RDP, do I? The funny thing is RDP rejects the connection instantaneously for my IP or DynDNS while it takes a while for another address. Thank you, Michael

    Read the article

  • Snap Server 18000 connection help!

    - by sicko666
    I wonder if anyone here can help me. I have a home server setup made up of old secondhand computers, 2 servers running Windows Server 2003, 1 workstation running Windows 7, a 16 port switch & an adsl ethernet modem. All these connect and talk to each other fine but then I got a "Snap Server 18000" and a "Snap disk 30sa" sata array. When I turn the Snap on, it boots past the BIOS, runs a kernel, then displays: This device cannot be managed via the video/kbd/mouse interface. The video is now disabled. You may access the management functions from your web browser. Only, none of the other PCs detect it, so no browser can find it! I have checked all cables, and all LEDs indicate there's a connection. I have installed the windows "iscsi" and the adaptec "Snap Server Manager" on all PCs but still it's not detected. I don't know what else to do, please advise!

    Read the article

  • How do I increase my home's bandwidth?

    - by Derek
    I just mistakingly posted this on Stack Exchange but don't know how to delete it... Anyway, I was thinking of building a home server to use instead of renting a VPS, because in the long run it would be cheaper. What I'm concerned with is the bandwidth limit of my house. I know when I'm downloading something off the internet, if I download at high speeds the rest of the computers connected to my router will become slower. Is there any way to avoid this? There are other cable outlets in my house, will connecting a modem and router there avoid this problem?

    Read the article

  • What's the difference between a wifi access point and station?

    - by Earlz
    I noticed that my (rooted) modem has some hidden modes for wifi. It has the default(and only setting without rooting) wireless access point, but it also has the settings repeater, ad-hoc, and station. What I'm really curious about is this station mode and how it differs from access point. I did a cursory search and didn't come up with any significant differences, other than that they are two distinct modes on many wireless chipsets. What is this station mode and how does it differ from access point?

    Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >