Search Results

Search found 2036 results on 82 pages for '70 536'.

Page 23/82 | < Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Fan running constantly on a Dell D420 laptop

  - by Halik

  I'm running latest Ubuntu 12.04 beta on a Dell D420 laptop. The fan is spinning almost constantly - even after turning the PC off, letting it cool down, and then turning it back on, the fan will turn on after some idle time. Not to mention any CPU work. The CPU temps are normal, in range of 50-55 idle, and up to 70 with some load. It wouldn't be an issue, but the same PC running Fedora, or Arch Linux, had a much more modest fan profile - the temps were managed while you seldom heard the fan. To counter the problem, I currently use i8k tools, set manual temperature thresholds which seemed to have worked, but the i8kmon has a tendency to cycle the fan between lower and higher state within aboutin a second intervals - which is extremely annoying. As far as I can tell I did not run any special software (beside laptop-mode-tools), or any additional kernel modules when running Arch Linux and I can't tell about Fedora.

  Read the article

• Two Wifi Icons in Panel [Solved]

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Collision Detection algorithms with early Collision exit

  - by Grieverheart

  I'm using collision detection in Monte Carlo simulations and at the moment I'm using GJK which is quite fast. I can't help to think it could be done even faster though. In the simulations, about 70% of the time GJK is run, it detects a collision. Thus collisions are more than non-collisions in my case. Most collision detection algorithms I know have an early non-collision exit test. Are there any collision detection algorithms that have an early collision detect instead of non-collision and could be potentially faster than GJK in case of collision?

  Read the article

• Successful technical communities except for open-source?

  - by Joshua Fox

  Have you ever seen a successful technical community -- e.g. user group, industry organization? Am I asking about a group of software engineers who get together F2F (or maybe online) and discuss technical and industry issues with deep zeal and interest -- a place where meaningful connections are made. Here are the only examples I have ever seen: Open source Maybe the Silicon Valley Java Users' Group Homebrew Computing Club in the '70's This sort of thing does exist in academia. Of course, there are lots of conferences and attempts at user's groups. However, almost all committed, serious software engineers, when asked about this, say "I don't have the time", which means that the organizations are not worthwhile to the best in our profession. Has anyone seen any organizations with an ongoing spirit of enthusiasm from top software engineers?

  Read the article

• T-SQL Tuesday - IO capacity planning

  - by Michael Zilberstein

  This post is my contribution to Adam Machanic's T-SQL Tuesday #004 , hosted this time by Mike Walsh . Being applicative DBA, I usually don't take part in discussions which storage to buy or how to configure it. My interaction with IO is usually via PerfMon. When somebody calls me asking why everything is suddenly so slow on database server, "disk queue length" or "average seconds per transfer" counters provide an overwhelming answer in 60-70% of such cases. Sometimes it can be...(read more)

  Read the article

• Wireless not working on Dell XPS 17 after installing 12.04

  - by user60622

  I (linux newbie) have a Dell XPS 17 and tried to install Ubuntu 12.04. After installation all WLAN accesspoints near are detected. But I can not connect (but I am able to connect with other computers as well as with Dell XPS 17 under windows). Outputs: iwconfig lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:"LerchenPoint" Mode:Managed Frequency:2.412 GHz Access Point: 58:6D:8F:A0:2D:58 Bit Rate=1 Mb/s Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-37 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:19 Missed beacon:0 eth0 no wireless extensions. sudo lshw -class network *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:99:98:28 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-24-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:50 memory:f0400000-f0401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:0a:00.0 logical name: eth0 version: 06 serial: f0:4d:a2:56:e3:94 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.123 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:47 ioport:6000(size=256) memory:f0a04000-f0a04fff memory:f0a00000-f0a03fff dmesg | grep iwl [ 10.157531] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 10.157561] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 10.157598] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 10.157599] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 10.157601] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 10.157731] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 10.157834] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 10.157976] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 10.179772] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 10.179775] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 10.179777] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 10.179796] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 10.574728] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 10.726409] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 19.714132] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 19.777862] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2251.603089] iwlwifi 0000:04:00.0: PCI INT A disabled [ 2266.578350] iwlwifi 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2266.578399] iwlwifi 0000:04:00.0: setting latency timer to 64 [ 2266.578435] iwlwifi 0000:04:00.0: pci_resource_len = 0x00002000 [ 2266.578437] iwlwifi 0000:04:00.0: pci_resource_base = ffffc90011090000 [ 2266.578439] iwlwifi 0000:04:00.0: HW Revision ID = 0x0 [ 2266.578704] iwlwifi 0000:04:00.0: irq 50 for MSI/MSI-X [ 2266.578808] iwlwifi 0000:04:00.0: Detected Intel(R) Centrino(R) Wireless-N 1000 BGN, REV=0x6C [ 2266.578916] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.600709] iwlwifi 0000:04:00.0: device EEPROM VER=0x15d, CALIB=0x6 [ 2266.600712] iwlwifi 0000:04:00.0: Device SKU: 0X50 [ 2266.600713] iwlwifi 0000:04:00.0: Valid Tx ant: 0X1, Valid Rx ant: 0X3 [ 2266.600727] iwlwifi 0000:04:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels [ 2266.605978] iwlwifi 0000:04:00.0: loaded firmware version 39.31.5.1 build 35138 [ 2266.606331] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs' [ 2266.614179] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S [ 2266.681541] iwlwifi 0000:04:00.0: L1 Enabled; Disabling L0S Solutions I tried: rfkill list all 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no echo "options iwlwifi 11n_disable=1" | sudo tee /etc/modprobe.d/iwlwifi.conf options iwlwifi 11n_disable=1 sudo modprobe -rfv iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. rmmod /lib/modules/3.2.0-24-generic/kernel/drivers/net/wireless/iwlwifi/iwlwifi.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/mac80211/mac80211.ko rmmod /lib/modules/3.2.0-24-generic/kernel/net/wireless/cfg80211.ko sudo modprobe iwlwifi WARNING: All config files need .conf: /etc/modprobe.d/blacklist, it will be ignored in a future release. replacing iwlwifi-1000-5.ucode (current driver) against iwlwifi-1000-3.ucode sudo jockey-gtk: (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed (jockey-gtk:2493): Gtk-CRITICAL **: gtk_icon_set_render_icon_pixbuf: assertion icon_set != NULL' failed nothing is listet in "Additional drivers" (german: "Zusätzliche Treiber"). gksudo gedit /etc/modprobe.d/blacklist.conf add "blacklist acer_wmi" Any help would be appreciated very much. Thanks!!

  Read the article

• Question about wifi connection files/certificates

  - by I_am_that_man-with-hair

  Here is the output i get when i run my school's wifi .py file for secure login. I "python SecureW2_JoinNow.py" I've emailed them about it, but wanted to take a shot and post here, could be on my end. I can't make sense of this error, although the last line makes me think it's on my end. Fresh install, so maybe that is it... Traceback (most recent call last): File "SecureW2_JoinNow.py", line 252, in <module> main() File "SecureW2_JoinNow.py", line 248, in main nm.connect() File "SecureW2_JoinNow.py", line 196, in connect wireless_device = nm_iface.GetDeviceByIpIface('wlan0') File "/usr/lib/python2.7/dist-packages/dbus/proxies.py", line 70, in __call__ return self._proxy_method(*args, **keywords) File "/usr/lib/python2.7/dist-packages/dbus/proxies.py", line 145, in __call__ **keywords) File "/usr/lib/python2.7/dist-packages/dbus/connection.py", line 651, in call_blocking message, timeout) dbus.exceptions.DBusException: org.freedesktop.NetworkManager.UnknownDevice: No device found for the requested iface.

  Read the article

• The Recovery: New Challenges for your Supply Chain!

  - by [email protected]

  Nearly half of CFOs are planning to reduce their inventory during the first half of 2010 in part due to supply chain improvements that allow them to hold less product, but also because of reduced demand according to Kate O'Sullivan, Sr Editor at CFO Magazine. Her view is based on this quarter's Duke University Global Business Outlook Survey. Highlights: Employment will be a drag on the economy- full-time employment to increase by 1%. Temp hiring to grow <1%, Outsourcing 4%.  70% of CFOs at SMEs say credit conditions are worse then 12 mos ago - placing strains on inventory growth Asia and China finance execs are more optimistic than their EMEA or US counterparts and expect stronger growth in capital spending with a 16% gain Source: "Slouching Towards Recovery", CFO Magazine, April 2010, pgs 19-20    

  Read the article

• Are certification courses worth it?

  - by Bill Williams

  I'm planning on getting certification in Database Development for SQL Server (MSTC - 70-433). I'm a junior level report writer at a new job and the company is offering to pay the majority, if not all, of training course fees. The course is five days. I noticed that MS has a self-paced training kit (book) that I could use. I'm wondering if this would be a better option because it will allow me to go as quick as possible. I've also heard about video training sessions (Lynda.com) but they seem to go at slow pace. My questions are: What should I expect at a certification course? Is it hands-on training? Small classes with personal feedback or not? Would I be better off learning at my own pace using the training kit? (I'd rather this not turn into a certifications are pointless discussion..)

  Read the article

• Software installed on root partition or on home partition

  - by Tim

  I am planning to install some big softwares such as Matlab (4GB), Mathematica (4GB) on my Ubuntu partitions. I was wondering if I installed them on my home partition, when I reinstall Ubuntu without touching the home partition, will the softwares still be runnable after reinstallation? what are the advantage and disadvantages of installing softwares on root partition and of on home partition? with your answer to the previous questions, what are some reasonable plans for the sizes of root partition and of home partition? Note that I would like to learn programming in C, C++, Java, Python, Lisp, databases under both Ubuntu and Windows, and no games. My laptop has around 230 GB, where I plan to install both Windows and Ubuntu, and reserve 40 GB for Ubuntu (three partitions: swap, root and home), 110 GB for NTFS partition shared between the two OSes, 70 GB for Windows OS partition, and 10 GB that can be added to any of the above partitions. I will change my plan according to your suggestions. Thanks and regards!

  Read the article

• Vdpau performance in Precise with Unity 3d

  - by bowser

  vdpau seems to be broken in Precise under Unity 3d. CPU usage ranges around 50-70% for 1080p movies while same movies utilizes around 5-10% in Natty with vdpau enabled (under Unity3d) The card is Nvidia G105m. It doesn't seem to be a Nvidia driver problem because in gnome-shell everything works as expected and I have tried different versions of Nvidia drivers (295.20, 295.33, 295.40 and the latest 302.XX from xorg-edgers) The results are all the same, works in Gnome Shell but not in Unity 3d. Disabling syn to vbank works if movie is not in full screen mode, but it doesn't work for full screen. I have searched around and haven't found much info. I am wondering if others are experiencing the same problem and if there are some known work around that I have missed. Unity 3d is otherwise very nice in Precise, but this is a show stopping issue for me (literally). Thanks. I have filed a bug here https://bugs.launchpad.net/unity/+bug/993397

  Read the article

• Could not apply stored configuration for monitors

  - by Hernantz

  Well this happened when I upgraded to Natty. Not only seems I can't change my resolution to higher than 1024x768 but it appears at the left and using only 70% of the monitor's width. I tried logging in but in ubuntu classic mode, and i was able to change it, but that trick did not work anymore. (May this be a compiz problem?) Anyways, here is my /var/log/Xorg.0.log http://pastebin.com/Ew4wwLab and lspci -nn | grep VGA: 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) I tried using xrandr for adding manually a resolution of 1280x1768 but without luck. Here is the xrandr output Screen 0: minimum 320 x 200, current 1024 x 768, maximum 4096 x 4096 LVDS1 connected 1024x768+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0*+ 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) TV1 disconnected (normal left inverted right x axis y axis) 1280x1024 (0xc6) 109.0MHz h: width 1280 start 1368 end 1496 total 1712 skew 0 clock 63.7KHz v: height 1024 start 1027 end 1034 total 1063 clock 59.9Hz

  Read the article

• How do I limit the size of my syslog?

  - by Wayne Werner

  I've got my mom's computer running Ubuntu 12.04 LTS. It's been working just fine but all of the sudden syslog has been filling up. And by filling up I mean I just deleted a /var/log/syslog that was 400GB in size. Yes - Gigabytes. While I'm sure there was some useful information in there, I'm not sure that 400GB is any kind of information to sift through. And what's really amazing about it is that it happened within a period of 8 hours - I had ran df around noon, and between then and now her drive filled up 30% (from just under 70% to 100%). What could be causing this and how could I fix it?`

  Read the article

• How long should my Html Page Title Really be?

  - by RandomBen

  How long should my text within my <title></title> tags really be? I know Google cuts it off at some point but when? When I used IIS7's SEO Toolkit 1.0 I get error stating my title should be under 65 characters. I have a book by Bruce Clay that states I should use from 62-70 characters and roughly 9 +/- 3 words. I also have used SenSEO's Firefox Add-on and it states I should use a max of 65 characters or roughly 15 words. What is the max really? I have 2 sources saying 65 and 1 saying 72 but Bruce Clay is generally kept in high regard.

  Read the article

• How to improve performance of ubuntu server 10.04 for my dms system?

  - by prasanna

  I will be using one of the dms (document management system) which is java + jackrabbit + postgresql + jboss + openoffice based on ubuntu server 10.04. this is the only application i will running on my server. i want to speed up the performance of the system for this. can you give me tips for improvements of ubuntu server? can i change any settings which give fast system performance. My application will be used concurrently by around 70 - 80 people. We have total 600 users. they will constanly upload , download the files in dms. i am going to use dedicated dell server with minimum 4 gb of RAM. i appreciate help. thanks and regards, Prasanna

  Read the article

• Why google is not crawling my website

  - by Aman Virk

  I am running a design and development blog http://www.thetutlage.com/ . From last couple of days my search traffic have been reduced from 70% to 10%. I myself is against black hat seo and all it do is write my own unique content almost everyday. Last week my search traffic was really good but now is dropping like heck. I have checked my webmasters dashboard and no message there from google. When i checked server logs i came to know last time google crawled my website was on 27 september 2012. Really i have no idea what i am doing wrong. I follow all google guidelines like bible, please help me

  Read the article

• How can I lower the CPU temperature?

  - by nmc

  I have installed Ubuntu 12.04 on my EeePC 1015PX and I've noticed that the CPU temperature does not go below 60ºC (70 is usual). Looking at powertop it seems the 2 cores (Atom N570) are idle most of the time. I've installed jupiter (w/ jupiter-eee-support) but it did not help. Edit: Meanwhile I've found out that echo 2 > /sys/devices/platform/eeepc-wmi/cpufv is supposed to turn on Super Hybrid Engine. Though it seems to help a bit (temperature goes down 2-3ºC), the temperatures are still in the 60-70ºc range.

  Read the article

• How to forward an Internet connection to another network?

  - by Naveen

  Can somebody please make a shot & sweet tutorial telling how to forward an Internet connection to different network interfaces in Ubuntu...? This is the idea: I'm using a 3G usb modem to get Internet on my laptop ,which is: ppp0 IP=10.225.174.70 My Wifi device is: wlan0 MAC=78:e4:00:d4:3d:85 These devices are determined from ifconfig command. I want to share ppp0's internet connection with wlan0 device, so I can connect any other device to wlan0 and browse internet from that device. Making a Hotspot using Network settings GUI doesn't do the trick because the other device won't receive Internet, it just connects to wlan0. I heard iptables can do this, but I'm totally confused by the alien commands seen online. I'm no expert in networking. Please compose a clear & simple answer using the above devices. This is a huge annoying problem for iPhone & tablet users came to Ubuntu from Windows.

  Read the article

• how do I go about removing all the language packs I don't need

  - by knotech

  I just noticed that in /usr/share/help I have the ubuntu help files in 70 different languages. I only speak 2, and I only really compute in one. I also noticed that it is full of broken symbolic links to /usr/share/help-langpack. I want just want to get rid of all the languages I don't need. How can I do this without getting all rm -r happy? I'm preferably looking for a way to do this without installing any new packages, as my main goal is to get rid of excess stuff on my machine. I'd like to find a way to do this preferably with dpkg, or apt.

  Read the article

• How do I start xterm with a headless system?

  - by NeViXa

  I'm running Ubuntu 12.04 and I want to boot directly and headless in the terminal (no GUI). After that I want to startx to start a program in xterm. When I boot 'headed', everything is working like supposed to, but: - When I boot headless, startx is not working (no screens found) I already tried to change xorg.conf to below, but it didn't not work: Section "Device" Identifier "VNC Device" Driver "vesa" EndSection Section "Screen" Identifier "VNC Screen" Device "VNC Device" Monitor "VNC Monitor" SubSection "Display" Modes "1280x1024" EndSubSection EndSection Section "Monitor" Identifier "VNC Monitor" HorizSync 30-70 VertRefresh 50-75 EndSection How can I boot headless and still be able to run startx? ANSWER: Adding the BusID to the Devices section in the xorg.conf above, fixed the problem for me. BusID "PCI:1:00:1"

  Read the article

• Sortie d'une nouvelle version stable de Chrome et de Chrome OS, et premier "Elite Award" pour le fix d'un bogue dans Chromium

  Sortie d'une nouvelle version stable de Chrome et de Chrome OS, et remise du premier "Elite Award" pour la correction d'un bogue dans Chromium Google vient de sortir très discrètement deux nouvelles versions de Chrome (8.0.552.237) et de Chrome OS (8.0.552.334), qui ne sont pas majeures mais néanmoins importantes. En effet, elles permettent de corriger plusieurs petites brèches, mais surtout un bogue "Elite" (critique), qui avait été découvert et signalé par Sergey Glazunov. Ce dernier devient de ce fait la première personne a être récompensée par la "Elite Security Reward" de Mountain View, qui se monte à 3.133,70 dollars. C'est la plus haute récompense à laquelle peut prétendre un indi...

  Read the article

• Resources on expected behaviour when manipulating 3D objects with the mouse

  - by sebf

  Hello, In my animation editor, I have a 3D gizmo that sits on the origin of a bone; the user drags the mesh around to rotate the bone. I've found that translating the 2D movements of the mouse into sensible 3D transforms is not near as simple as i'd hoped. For example what is intuitively 'up' or 'down'? How should the magnitude of rotations change with respect to dX/dY? How to implement this? What happens when the gizmo changes position or orientation with respect to the camera? ect. So far with trial and error i've written something (very) simple that works 70% of the time. I could probably continue to hack at it until I made something that works 99% of the time, but there must be someone who needed the same thing, and spent the time coming up with a much more elegant solution. Does anyone know of one?

  Read the article

• My Ubuntu drive is running out of space, how to fix, something is wrong

  - by Jamie Flores

  I'm moving from windows and am having trouble figuring this out: I'm getting a message that pops up saying disk space is low. It says I have 800MB free. I click on the disk usage analyzer and it shows 24.6 total capacity and 22.5 used. When I look in GParted it shows a partition at 72.6GB where I have Ubuntu installed. It also shows that 70.65GB used and 1.94 free in that partition. How do I figure out what else is in that partition? It's the only ext4 format. What am I missing?

  Read the article

• Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

  Read the article

• Wireless speed drops over time and doesn't get up if not reconnected

  - by Vili Lehto

  I am using Ubuntu 12.10 64bit and I have a Asus PCE-N15 wireless card(in PCI-E slot). The problem is that first when I connect to my WiFi network the speed is just fine, and actually my link speed never drops, it shows a solid 150mb/s+ link speed and good signal. But the download and upload speeds drop dramatically after couple minutes of use and I have to reconnect to fix this. Network is type IEEE 802.11bgn and uses WPA2/AES encryption. I don't have similar problems on the windows side, and the network is working fine on every other device. iwconfig shows this: wlan0 IEEE 802.11bgn ESSID:"WLAN-AP" Mode:Managed Frequency:2.412 GHz Access Point: 00:1E:AB:05:EF:31 Bit Rate=300 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr=2347 B Fragment thr:off Encryption key:off Power Management:off Link Quality=61/70 Signal level=-49 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:2 Missed beacon:0 So the question is: Is there a way to fix this? Thanks in advance.

  Read the article

< Previous Page | 19 20 21 22 23 24 25 26 27 28 29 30  | Next Page >