Search Results

Search found 19557 results on 783 pages for 'networking programming'.

Page 232/783 | < Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >

• XP - ping changes routing table?

  - by Corelgott

  Hey Folks, I have got a real strange behaviour with one of my XP-Sp3 machines. Setup: A Server in the lan (192.168.5.0) proviedes access to all roadwarriors in 10.8.0.0 The DCHP has a static route for all clients pronouncing 192.168.5.235 as gateway for 10.8.0.0 All Clients can ping & access the vpn-machines; everything works like a charm But one Xp-Sp3 is not willing to connect to them. It gets all the same routes as any other sytem in the lan and I trippel-checked - there are no static routes on this machine When I ping any 10.8.0.0 device from this machine, the first two packaged work like a charm; but the next two (and any package after them) fail and get lost. When I look back into the routing table: There is a new route; a special one just for the device I pinged, which points to the right gateway - but which wasn't there earlier... As Long as this route exists the machine can't ping anything on 10.8.0.0. But if I remove the route by hand: The next to ping packages work fine... Has anybody got an idea about that? Anybody every seen such a behaviour? Any hint / help / tip is greatly appreachiated! thx in advance Corelgott Ps: I attach an image of the cmd to clarify things - its in german, but reading a routing table shouldn't be that hard...

  Read the article

• Is there a utility to visualise / isolate and watch application calls

  - by MyStream

  Note: I'm not sure what to search for so guidance on that may be just as valuable as an answer. I'm looking for a way to visually compare activity of two applications (in this case a webserver with php communicating with the system or mysql or network devices, etc) such that I can compare the performance at a glance. I know there are tools to generate data dumps from benchmarks for apache and some available for php for tracing that you can dump and analyse but what I'm looking for is something that can report performance metrics visually from data on calls (what called what, how long did it take, how much memory did it consume, how can that be represented visually in a call stack) and present it graphically as if it were a topology or layered visual with different elements of system calls occupying different layers. A typical visual may consist of (e.g. using swim diagrams as just one analogy): Network (details here relevant to network diagnostics) | ^ back out v | Linux (details here related to firewall/routing diagnostics) ^ back to network | | V ^ back to system Apache (details here related to web request) | | ^ response to V | apache PHP (etc) PHP---------->other accesses to php files/resources----- | ^ v | MySQL (total time) MySQL | ^ V | Each call listed + time + tables hit/record returned My aim would be to be able to 'inspect' a request/range of requests over a period of time to see what constituted the activity at that point in time and trace it from beginning to end as a diagnostic tool. Is there any such work in this direction? I realise it would be intensive on the server, but the intention is to benchmark and analyse processes against each other for both educational and professional reasons and a visual aid is a great eye-opener compared to raw statistics or dozens of discrete activity vs time graphs. It's hard to show the full cycle. Any pointers welcome. Thanks! FROM COMMENTS: > XHProf in conjunction with other programs such as Perconna toolkit > (percona.com/doc/percona-toolkit/2.0/pt-pmp.html) for mySQL run apache > with httpd -X & (Single threaded debug mode and background) then > attach with strace -> kcache grind

  Read the article

• Wireless Disabled:HardBlock

  - by wisdom

  Really I don't know where can I solve my problem.....I'm searching for ages everyone has solved it but me not yet ! It's Wireless HardBlock problem... I posted this question when I was using ubuntu 11.10 on askubuntu and no hope ! here are some solved problems which I tried but mine not solved ! (1,2,3) I'm using now Fedora17 beside Xubuntu where no problem with wireless card ! Anyone can give me hope to solve it ? thanks in advanced

  Read the article

• Is this anycast behaviour correct?

  - by etheros

  When connecting to an service provided using anycast, I am experiencing different behaviour depending on whether the request is made using TCP or UDP. With TCP, the request is made to address A, and the subsequent response also comes from A. With UDP however, while the request is made to A, the response comes from address B. Is this correct behaviour, or should the UDP response come from the same address it's sent to?

  Read the article

• routing weirdness - traceroute 'vanishes' en route

  - by The Journeyman geek

  I'm attempting to set up one of my boxes as a server (again), but i'm having some odd connection issues- the box itself connects fine to the internet, but trying to connect to my external ip address seems to result in the trace getting 'lost' partway. http://pastebin.com/HCQAGbvn - this is a traceroute from another system that's connected to another ISP - starhub is my own one, while i have another system that i have access to on singtel. I'm wondering if my ISP is messing around with routing, or is something very odd going on. As you note, the traceroute dosen't reach me, but if it helps, i use a dd-wrt router. edit: Facepalmishly, turning the firewall on my router on and off fixed it. I don't get why it dropped off at different ip addresses each time, or why the router set it self to block.. everything, or why it affected the ipv6 tunnel as well.

  Read the article

• Linux NetSec/IDS Bridge

  - by Blackninja543

  What I am looking to make is a linux system that acts as a bridge. It simple forwards any data sent on one device over to the next device. It does not attempt to block incoming attacks or redirect any traffic. What it does to is perform an IDS role on the network. Any suspicious activity is logged and reported. Snort would be one such piece of software however I was wondering what other solutions and ideas the rest of the community has.

  Read the article

• Building a network at home, what cables to use (if any)?

  - by Faruz

  My house is currently in ruins and am building it. While doing so, I wanted to design a home network. My main objectives are surfing and HD streaming. The house is one-level, 100 sq/m (about 300 sq/ft), and one of the rooms is a safety room with Reinforced concrete walls. About a year ago, when I started planning, I thought about putting Cat 6 STP cables in the walls and create network points in the rooms. Should I use STP or FTP? I heard that STP is a problem regarding connectors and stuff. Is it really beneficial? Will it work OK if I transfer the wire together with the telephone line? Should I maybe go with WLan and count on 802.11n to enable me to stream HD across the house? is 802.11n that good?

  Read the article

• How to connect computers to a network printer behind a router?

  - by kokbira

  General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

  Read the article

• Colocation and HSRP setup

  - by WinkyWolly

  My colocation provider has setup HSRP for us and has provided us 2 drops (plugged into 1/1/1 and 1/1/2) from their routers as well as a /29 with 2 HSRP IP's and the rest of the /29 usable for the switch. I know that HSRP should be pretty much plug and play as long as the ports are in the same VLAN. However I'm confused as to how to the IP setup should work. Currently I've assigned port 1/1/1 the full /29 however I think this is incorrect because if I were to unplug it port 1/1/2 wouldn't work as it has no IP assignment. What's the proper way to do this?

  Read the article

• How to link processing power of old computers together?

  - by redIago

  Hey all, I'm sitting on 8 old computers of varied sorts that are more or less useless at this point for any other purpose really. Is there a way I could link their hardware or processing power or whatever together over wifi and use one as like a central computer? Like it would be cool to distribute the processing of some video game or encryption generating program over the collective computers. Any way to do all this? Thanks.

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• VirtualBox cloned Ubuntu Server network error

  - by Luke

  I run a number of virtual servers on my network and I want to be able to easily clone base installations of Ubuntu Server. I use the VBoxManage command to clone the actual hard disk and I then create a new profile for my VM and copy over the settings of the original VM. However, when I boot into the cloned VM, there seems to be a network problem. When I issue a PING I get the message "Network unreachable". I traced it down to the fact that the virtual network card of the cloned VM has a different MAC address then the original VM. When I copy the MAC address the clone seems to work fine. How can I have the cloned VM have it's own MAC address?

  Read the article

• Duplicate name exists solution

  - by user978733

  I have about 70 pc's with exactly same hardware. I decided to automate turning on and off. I took 1 PC. Here is what I've done: Changed bios configuration so that now pc's waking when I turn on AC switch Installed Windows XP and configured so that I can turn off remotelly, changed workgroup name to "WG1", and pc name to "ExamPC" Then created acronis backup image of this pc I installed this image in several PC's and tried to test All worked well till windows opened. The problem is, all tested PC's started Windows nearly at the same time, and all of them popped up error Duplicate name exist. I can't figure out any solution. Any suggestions?

  Read the article

• Why are my downloads up to ~1500KByte/sec only, when the ADSL connection locks at 13611Kbit/s?

  - by leladax

  No uploading is going on other than the overhead of downloading which appears to be not high for the abilities of the connection: Only about 30-40KByte/s when the router locks at 1012Kb/s and other direct uploads or uploading overheads can reach more than 100KByte/sec so I don't think it's a congestion at uploading that is doing it. Is there something I miss? Because I assume 13611Kbit/s should be ~1701Kbyte/sec. Is it an overheard at the ADSL level I don't understand? Could it be the ISP doing it? If it's active throttling it can't be on single connections since 2 high speed connections still go up to ~1500KByte/sec. It's not an example on torrents or other complex situations. The tests were on Ethernet, but I doubt the results would be different on wireless. I wonder if the settings of those connections at my end could be doing it, e.g. MTU settings, though I haven't touched the defaults of a common Realtek NIC.

  Read the article

• Mac OS X will only upload zero-byte files through FTP

  - by tabacitu

  I'm using Mac OS X Lion and i've been having this problem with FTP (any FTP client, mind you. I tried Transmit, FileZilla, Cyberduck and the Terminal, all with the same result) I can browse files in my FTP Client, but when I upload files, the client hangs for a few seconds, then thinks it uploaded the files successfully, but it only creates a new file with one blank line in it. Sometimes, it manages to upload 4-5 lines. It then returns: 226 - Error during read from data connection 226 Transfer aborted But 2xx is a success message. It is not a server issue, since any Windows machine will upload just fine using the same network. Can anybody figure out what the problem is? It renders my mac useless for web development. The problem persists with SFTP and FTP with SSL/TLS. Later edit: Solved! Ok, turns out the problem goes away when I take out my router and connect directly through PPPoE. So the problem is with the router, I thought. But no, the problem is with the mac that connects through a router that connects through a PPPoE and tries to upload using FTP. Pretty specific, I know. The problem is with the MTU (maximum transmission unit). Apparently, mac os x breaks the file into chunks that are too large for the router to send, because the router's MTU was set lower than Mac OS X's. My router's was 1492, which is ok, but my Mac's MTU was 1500, which is unacceptable. I don't even understand why it works directly with PPPoE. Anyway, if you encounter the same problem, this is how you diagnose and fix it: In terminal, run: ifconfig | grep mtu to see what the MTU is for en0 (or en1, mine was en0) If it's 1500, run sudo ifconfig en0 mtu 1300 This should solve it. If so, it may only be until the next restart. You can also change the MTU in System Preferences \ Network \ Ethernet - Advanced \ Hardware

  Read the article

• Set 802.1Q tagged port on VLAN1 on Dell PowerConnect switch

  - by Javier

  I'm having big troubles when adding this Dell switch to my network. Here we use several VLANs to segment traffic. All switches (3com and DLink mostly) have configured the same VLANs, most ports are 'untagged' and belong to a single VLAN, except for the ports used to join together the switches (in a star topology), these ports belong to all VLANs and use 802.1Q tags. So far, it works really well. But on this new switch (a Dell PowerConnect 5448), the settings are very different (and confusing). I have configured the same VLANs, an the uplink ports are set in 'general' mode (supposed to be fully 802.1Q compliant), I can set the VLAN membership as 'T' on these ports for all VLANs except VLAN 1. It always stay as 'U' on VLAN 1. Any ideas?

  Read the article

• Several border firewalls in the same network

  - by nimai

  I'm currently analyzing the consequences of multipath connections for the firewalls. In that context, I'm wondering if it's really uncommon to have several firewalls at the borders of a network to protect it. The typical case I'd imagine would be a multihomed network, for which the administrator would have different policies for links from different (or not) ISPs. Or maybe even in an ISP's network. What would be the practical (dis)advantages of such a configuration? Could you provide an example of an existing topology using several border firewalls?

  Read the article

• Same network same switch but computers can't talk "ping"to eachother [closed]

  - by Sue

  Possible Duplicate: How does IPv4 Subnetting Work? Each computer(all 2 of them) can ping the router but can't ping each-other and firewall is off. Same default gateway, IP address very similar (just two number away at end) but the subnet mask is different between these two computers. One ends in 192 the other 224. There is a switch between them that then connects to the router. Why can't the computers ping each-other?

  Read the article

• How to use a Network adapter only for a specific Connection on Win7?

  - by Tokk

  Hey, Guys I've got several network adapter in my PC (from LAN, WLAN, VPN etc...) and what I want to accomplish is that some specific adresses use the VPN adapter, while all others use eiter LAN or WLAN. (So for example http://win-server/ is using VPN, while www.google still uses LAN connection.) I've want to solve this with the Windows settings and not the VPN settings to make sure I can do it with every VPN-Provider. Thank You

  Read the article

• OpenVPN bridge network from routed clients

  - by gphilip

  I have the following setup: subnet 1 - 10.0.1.0/24 with a machine used as NAT and also running an OpenVPN client subnet 2 - 192.168.1/24 with an OpenVPN server (the server in subnet 1 connect here) subnet 3 - 10.0.2.0/24 that uses the NAT machine (subnet 1) to access the internet, so all non-local traffic is routed there to the eth0 interface The OpenVPN client creates the tun0 interface and appropriate routing so that I can access machines from 192.168.1/24 [root@ip-10-0-1-208 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... Connected to 192.168.1.186. Escape character is '^]'. [root@ip-10-0-1-208 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 10.0.1.1 0.0.0.0 UG 0 0 0 eth0 10.0.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.1 10.8.0.5 255.255.255.255 UGH 0 0 0 tun0 10.8.0.5 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 169.254.169.254 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 192.168.0.0 10.8.0.5 255.255.0.0 UG 0 0 0 tun0 However, when I try the same from subnet 3, it can't reach that machine. [root@ip-10-0-2-61 ~]# telnet 192.168.1.186 8081 Trying 192.168.1.186... I suspect that it's because subnet 3 is routed to eth0 on the NAT machine in subnet 1 and it cannot jump to tun0. What's the easiest way to resolve it? I don't want to use iptables. I can't change the routing from machines in subnet 1 because it's done in AWS and so it works only with specific interfaces. Also, the NAT machine gets its IP with DHCP and so bridging is a bit complicated. IP forwarding is set on the NAT machine [root@ip-10-0-1-208 ~]# cat /proc/sys/net/ipv4/ip_forward 1 Thank you!

  Read the article

• Suggestion of device WiFi range in it's spec. Possible?

  - by SeeR

  I have router Draytek Vigor 2100VG at home almost in the center of it. The farthest point at my home is my balcony, ~12m from it. I have constant wifi signal range problems with some of my devices, but not with others. Notebook Lenovo W510 - no problems Nokia Home Music - always on 10m - no problems Sony PS3 - always on 7m - no problems Sony tablet S - problems around 6m Sony PSP - problems around 8m Sony PS Vita - problems around 8m Nokia E63 - problems around 8m I'm curious why my Notebook don't have any problems even on the balcony? I guess it has better hardware or uses more power for transmission. This information is really important when you want to buy new device/computer, so my real question is: Can device wifi range can somehow be found/suggested from official hardware technical specification? If not Is there some web page with wifi range reviews?

  Read the article

• Remote access to a KVM Ubuntu virtual server

  - by Lee

  I've just setup an ubuntu virtual server and everything seems to be working fine. I used KVM to get it working with a bridged network. I've given the virtual server a static ip address on my network. I don't seem to be able to connect to the virtual machine though from outside my network. If I'm on my own network it all works fine, I can ping the ip and connect to it. The virtual server can ping other machines and sites on the internet. I changed the port forwarding rules on my router to forward any connections on a specific port to the virtual server ip address thinking that was the problem, but it was still the same. Is there something I'm missing here which is blocking outside connections to the virtual machine? Thanks.

  Read the article

• Wifi channel interference

  - by artfulrobot

  In my neighbourhood there are: 11 wifi signals on channel 1 2 wifi signals on channel 4 (including mine at the mo) 8 on channel 6 6 on channel 11 According to the diagram on wikipedia Mine on channel 4 will suffer interference from channel 1 and channel 6, so a total of 20 other networks(!). So would I be better to join channel 11, even though my network is then in direct competition with the 6 others? I suppose the question is: what's worse: direct interference (meaning that on the same channel) from 6 or fringe interference from many more networks?

  Read the article

• HP laptop won't recognize wireless adapter

  - by Dennis Williamson

  I have an HP Pavilion dv6400 series laptop with an NVidea chipset which is the subject of a class action lawsuit. The symptom (PDF) that I'm experiencing is that the system fails to recognize that there is a wireless adapter installed. It doesn't appear in Device Manager. Is there some way, short of installing a new adapter, that I can work around this problem? The system is running Windows Vista Home and has the latest BIOS (F42) and Windows updates and drivers. See this related question where I ask how to use an old Windows Mobile phone as a Wi-Fi (not cellular data) tether.

  Read the article

• How do I stop someone from saturating my line & wasting CPU cycles

  - by JoshRibs

  My web host shows inbound & outbound traffic with mrtg. I have a steady 3.5mbps inbound traffic from Nigeria. Even assuming the source IPs & destination ports are blocked with Iptables & verifying nothing is listening on those ports, will the traffic still always pass through the switch & "get" to my server (where my server wastes CPU cycles "dropping" the packets)? Assuming I was setup with a hardware firewall, the traffic would still show in mrtg assuming the firewall is behind the switch? So is there any way to stop someone from saturating your 100mbps line, if they also have a 100mbps line? Other than filing an abuse complaint with the kind folks in Nigeria?

  Read the article

< Previous Page | 228 229 230 231 232 233 234 235 236 237 238 239  | Next Page >