Search Results

Search found 33496 results on 1340 pages for '32 vs 64 bit'.

Page 233/1340 | < Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >

• pptpd-logwtmp.so config wrong ip address

  - by rgc

  i have setup a pptp vpn on ubuntu 10.04, and i config local ip address , remote ip address as following: local IP address 10.0.30.100 remote IP address 192.168.13.100 after i use windows to connect to vpn server in windows , i only could send packets, can not receive any packets. i also check the pptp log in ubuntu server, and find this strange thing rcvd [IPCP ConfAck id=0x1 <compress VJ 0f 01> <addr 10.0.30.100>] rcvd [IPCP ConfReq id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] sent [IPCP ConfAck id=0x2 <compress VJ 0f 01> <addr 192.168.13.100> <ms-dns1 202.119.32.6> <ms-dns2 202.119.32.12>] Cannot determine ethernet address for proxy ARP local IP address 10.0.30.100 remote IP address 192.168.13.100 pptpd-logwtmp.so ip-up ppp0 **172.25.146.174** i did not set 172.25.146.174, it should be 192.168.13.100, can anyone tell me what should i do to fix this problem?

  Read the article

• RTNETLINK answers: Invalid argument

  - by LinuxPenseur

  Hi, When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

  Read the article

• Why can't I route to some sites from my MacBook Pro that I can see from my iPad? [closed]

  - by Robert Atkins

  I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

  Read the article

• Autohotkey script multiple functions

  - by Vince

  Is it possible to use this bottom script but add a second hotkey and function that goes with it. ;DoOver.ini ;[Settings] ;record={LCtrl}{F12} ;hotkey to start and stop recording ;playback={LCtrl}{F5} ;hotkey to start playback ;keydelay=10 ;ms to wait after sending a keypress ;windelay=100 ;ms to wait after activating a window ;movemouseafter=1 ;move the mouse to original pos after playback 1=yes 0=no [Settings] record={LCtrl}{F12} playback={LCtrl}{F5} keydelay=10 windelay=100 movemouseafter=1 macro={WinActive}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{LCTRL Down}{Right}{Right}{LCTRL Up}{LSHIFT Down}{End}{LSHIFT Up}{LCTRL Down}{c}{LCTRL Up}{MouseClick,L,236,116,1,0,D}{MouseClick,L,54,116,1,0,U}{LCTRL Down}{LCTRL Up}{MouseClick,L,474,64,1,0,D}{MouseClick,L,474,64,1,0,U}{MouseClick,L,451,77,1,0,D}{MouseClick,L,451,77,1,0,U}{MouseClick,L,44,225,1,0,D}{MouseClick,L,44,225,1,0,U} OR playback={LCtrl}{F7} keydelay=10 windelay=100 movemouseafter=1 macro={WinActive}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{LCTRL Down}{Right}{Right}{LCTRL Up}{LSHIFT Down}{End}{LSHIFT Up}{LCTRL Down}{c}{LCTRL Up}{MouseClick,L,236,116,1,0,D}{MouseClick,L,54,116,1,0,U}{LCTRL Down}{LCTRL Up}{MouseClick,L,474,64,1,0,D}{MouseClick,L,474,64,1,0,U}{MouseClick,L,451,77,1,0,D}{MouseClick,L,451,77,1,0,U}{MouseClick,L,44,225,1,0,D}{MouseClick,L,44,225,1,0,U} Maybe add something like what is printed in bold here. I know the coding isnt right here, but i think this is the best way to describe what I am looking for. Anybody?

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• Can any postfix guru assist me determine how emails are still being sent via my server from unauthorized sources?

  - by Dave

  Hi all, I'm getting a little concerned as I run a small server hosting a number of websites and manage the email for a few dozen people. Just recently though I've had a couple of notifications from spamcop alerting me that spam has been sent from my server, and when I have a look over the logs from time to time I can indeed see that there are many repeated attempts of mail being sent from my server. Most of the time it gets knocked back from the destination servers but sometimes its getting through. Unfortunately I'm not linux or postfix expert, I can get by but had though I had my machine locked down quite securely, I don't allow relaying, when I check the online DNS/MX tools they tend to report my server as being OK so I'm not sure where to take it now and hoping someone might be able to throw me a few pointers. I get lots of entries like this in my MAIL.INFO log Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 66B88257C12F: from=<>, size=3116, nrcpt=1 (queue active) Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 614C2257C1BC: from=<[email protected]>, size=2490, nrcpt=3 (queue active) and Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6471]: 0A316257C204: to=<[email protected]>, relay=none, delay=384387, delays=384384/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6470]: 5848C257C20D: to=<[email protected]>, relay=none, delay=384373, delays=384370/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) then there tends to be connection timeouts, so from what I see even though I had relaying disabled.. something is getting by and trying to send.. So if you can help that will be greatly appreciated, and any further logging/config info I can supply. Thanks

  Read the article

• convert decrypted .vobs to .avi with ffmpeg on ubuntu

  - by Arcath

  I have a .vob file that has bee ripped from a dvd, when I watch the .vob its very good quality video and 5.1 english audio but when I use ffmpeg it has rubbish video and mono french audio. That was using this command: ffmpeg -i /samba/ripping/vobs/12161840#2.vob -f avi /samba/ripping/avis/test.avi I've tried a few different variations on that but it never comes back with anything good just bigger files with bad video and incorrect sound. I know the videos good and the correct audio streams exist so how do I select a 5.1 track and get good video? ffmpeg gives the .vob details as: Input #0, mpeg, from '/samba/ripping/vobs/12161840#2.vob': Duration: 00:42:05.56, start: 0.287267, bitrate: 5738 kb/s Stream #0.0[0x1e0]: Video: mpeg2video, yuv420p, 720x576 [PAR 64:45 DAR 16:9], 8436 kb/s, 25 fps, 25 tbr, 90k tbn, 50 tbc Stream #0.1[0x80]: Audio: ac3, 48000 Hz, 5.1, s16, 384 kb/s Stream #0.2[0x81]: Audio: ac3, 48000 Hz, 5.1, s16, 384 kb/s Stream #0.3[0x82]: Audio: ac3, 48000 Hz, mono, s16, 192 kb/s Output #0, avi, to '/samba/ripping/avis/test.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 720x576 [PAR 64:45 DAR 16:9], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, mono, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.3 -> #0.1

  Read the article

• Ram question in VMware Server 2

  - by ToreTrygg

  Hi, I understand from the VMware Server 2 documentation that VMware Server 2 is capable of running a 64-bit guest OS underneath a 32-bit host OS, as long as the hardware running the box is 64-bit capable. Here's my situation. We currently have an underutilized XEON X3220 Quad Core 64bit Server, running Server 2003, 32-bit and 2gb of RAM (the motherboard is capable of 8gb ram). The server is currently used mainly for file and print services. It is also running Active Directory, Novell eDirectory and Groupwise 6.5. We are planning a micration to Microsoft Exchange, so the Novell eDirectory and Groupwise services will eventually be purged from this box, leaving only Active Directory, File and Print services. Being that this server is underutilized we are hoping to save hardware costs and virtualize our new Exchange investment. My question is this. Will VMware allow access to the "invisible" extra memory that Windows 32-bit won't see. Meaning, if we increase the full amount of system ram to 8gb (yes, I know the 32-bit host OS will only see a maximum of 4gb), will I be able to assign maybe 5gb to the new Server 2008 64-bit OS running Exchange and leave 3gb for the Guest OS (or maybe even a 6, 2 split). The second part of that would be, would it be better to just convert the main OS currently running to an image, convert the machine itself to ESXi and run both OSes as images under ESXi. Downtime for this box is critical, so my preference is most definitly with the first option because it presents very minimal downtime. Doing the second would make downtime quite a few hours to image the machine and then convert the image to a VMware Image.

  Read the article

• ubuntu dmidecode is not functioning properly

  - by Alaa Alomari

  dmidecode is giving irrelevant and conflicted results. it shows that i have two slots while the correct is 8 (the board is Tyan S5350.) uname -a Linux synd01 3.0.0-16-server #29-Ubuntu SMP Tue Feb 14 13:08:12 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@synd01:/home/badmin# dmidecode -t 16 dmidecode 2.9 SMBIOS 2.33 present. Handle 0x0011, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 2 while root@synd01:/home/badmin# dmidecode -t 17 | grep Size Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB also lshw shows: *-memory description: System Memory physical id: 11 slot: System board or motherboard size: 4GiB *-bank:0 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 0 slot: J3B1 clock: 166MHz (6.0ns) *-bank:1 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 1 slot: J3B3 clock: 166MHz (6.0ns) *-bank:2 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 2 slot: J2B2 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:3 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 3 slot: J2B4 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:4 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 4 slot: J3B2 clock: 166MHz (6.0ns) *-bank:5 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 5 slot: J2B1 clock: 166MHz (6.0ns) *-bank:6 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 6 slot: J2B3 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:7 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 7 slot: J1B1 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) what might cause this conflict and how can i fix it? Thanks

  Read the article

• IRC server connecting to another server

  - by Oxinabox

  I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Where do vendors publish internal transfer rates of HDDs?

  - by red888

  So I've started to dig into storage fundamentals and found that in order to calculate the IOPS of a HDD you need to know the internal transfer rate of the drive (time it takes data to move from the platters to internal disk's cache). I went on newegg and even a few vendor sites and could not find this info published for any HDDs. Is it sometimes called something else? Take this link to a seagate HDD for instance. Nowhere do I see "internal transfer rate", but I do see something called "Sustained Data Rate OD"- is that the same thing? Just so you know where I'm getting this info (Book: "Information Storage and Management Storing, Managing..."): Consider an example with the following specifications provided for a disk: The average seek time is 5 ms in a random I/O environment; therefore, T = 5 ms. Disk rotation speed of 15,000 revolutions per minute or 250 revolutions per second — from which rotational latency (L) can be determined, which is one-half of the time taken for a full rotation or L = (0.5/250 rps expressed in ms). 40 MB/s internal data transfer rate, from which the internal transfer time (X) is derived based on the block size of the I/O — for example, an I/O with a block size of 32 KB; therefore X = 32 KB/40 MB. Consequently, the time taken by the I/O controller to serve an I/O of block size 32 KB is (TS) = 5 ms + (0.5/250) + 32 KB/40 MB = 7.8 ms. Therefore, the maximum number of I/Os serviced per second or IOPS is (1/TS) = 1/(7.8 × 10^-3) = 128 IOPS.

  Read the article

• ipv6 reverse DNS delegation

  - by user1709492

  I currently have 2001:1973:2303::/48 assigned to me and i'll be assigning /64's to customer's I'd like to have 1 zonefile for the /48 where i can essentially point / redirect query to different nameservers. Example ( Desired effect ) 2001:1973:2303:1234::/64 -> ns1.example.com, ns2.example.com 2001:1973:2303:2345::/64 -> ns99.example2.com, ns100.example2.com 2001:1973:2303:4321::/64 -> ns1.cust1.com, ns2.cust1.com Current /48 zonefile $TTL 3h $ORIGIN 3.0.3.2.3.7.9.1.1.0.0.2.ip6.arpa. @ IN SOA ns3.example.ca. ns4.example.ca. ( 2011071030 ; serial 3h ; refresh after 3 hours 1h ; retry after 1 hour 1w ; expire after 1 week 1h ) ; negative caching TTL of 1 hour IN NS ns3.example.ca. IN NS ns4.example.ca. 1234 IN NS ns1.example.com. NS ns2.example.com. 2345 IN NS ns99.example2.com. NS ns100.example2.com. 4321 IN NS ns1.cust1.com. NS ns2.cust1.com. Where am i going wrong ? My request seems simple to me atleast. To put it in terms of firewalling i want to redirect traffic client queries 2001:1973:2303:4321::1 - ns3.example.ca sees the request and redirects the query to ns1.cust1.com - ns1.cust1.com answers the query with omg.itworks.ca ( provided ns1.cust1.com is properly configured.

  Read the article

• Not able to access Silverlight.net and ONLY Silverlight.net - All other domains work!

  - by Sootah

  Alrighty folks, I have an extremely odd problem. I am able to surf the web fine with one odd (and really annoying at the moment) exception: Microsoft's Silverlight.net. Every other site that I go to works just fine. This is quite frustrating because I'm in the middle of programming a web app in Silverlight 4.0, and whenever I do a search for any code examples, tutorials, or whatnot at least 50% of the results are hosted in the silverlight.net forums. The error message that I get is: Oops! Google Chrome could not find www.silverlight.net It doesn't work in my other browsers either (both IE and FireFox). What's odd, is that while the error message would lead me to assume it's a DNS error, I can ping the URL just fine. C:\Users\The Doot>ping silverlight.net Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Ping statistics for 206.72.125.201: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 103ms, Maximum = 110ms, Average = 106ms I've checked my HOSTS file, and there's nothing that refers to ANY Microsoft URL in there. What could be causing this!?? More importantly, how do I fix it? Just for kicks, I've even included the results of a traceroute here for your enjoyment. OS: Windows 7 Ultimate Thanks in advance! -Sootah

  Read the article

• Advertise a subnet route with radvd

  - by Thomas Berger

  we have set up a small IPv6 Testing network. The setup looks like this: ::/0 +----------+ | Firewall | Router to the public net +----------+ | 2001:...::/106 | +----------+ +-------| SIT GW | sit Tunnel gatway to the some test users | +----------+ | +----------+ | Test Sys | Testsystem +----------+ The idea is to advertise the default route from the firewall and the route for the SIT subnets from the sit gateway. The configurations for radvd are: # Firewall interface eth0 { AdvSendAdvert on; route ::/0 { }; }; # SIT Gatway interface eth0 { AdvSendAdvert on; route 2001:...::/106 { }; }; We have captured the adv. packages with tcpdump and the packages looks good. We see a default route from the fw, and the subnet route from the SIT gatway. But if we look on the testsystem there are two default routes over both gateways. There is no subnet route. The routing does not work of course. Here the routes we get: 2001:.....::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::baac:6fff:fe8e:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 default via fe80::e415:aeff:fe12:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 Any Idea?

  Read the article

• Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

  - by Gleeson9

  Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

  Read the article

• Proper configuration for Windows SMTP Virtual Server to only send email from localhost, and tracking down source of spam emails

  - by ilasno

  We manage a server that is hosted on Amazon EC2, which has web applications that need to be able to send outgoing email. Recently we received a notice from Amazon about possible email abuse on that server, so i've been looking into it. It's Windows Server Datacenter (2003, i guess), and uses SMTP Virtual Server (you know, the one that requires IIS 6 for admin). The settings on the Access tab are as follows: - Authentication: Anonymous - Connection: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) - Relay: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) In the SMTP logs there are many entries like the following: 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 FROM: 0 0 4 0 26364 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 TO: 0 0 4 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26707 SMTP - - - - ([email protected] is sending quite a lot of emails :-/) Can anyone confirm if the SMTP server settings seem correct? I'm also wondering if a web application on the machine could be exposing a contact form or something that would allow this sort of abuse, looking into that (and how to look into that) further.

  Read the article

• Nginx Server Block Not Working? - Already running other vhosts just this one not working

  - by daveaspinall

  Im running a Debian 6 LEMP server with multiple virtual hosts and everything has been fine for 5 or so sites. But I've just tried adding another but for some reason it's just not working. By not working I mean in Chrome I get the "Oops! Google Chrome could not connect to subdomain.domain.net" error. I've changed the domain for security to subdomain.example.com and the IP is masked. Hosts file (I have multiple sub domains): xxx.xxx.xx.xxx *.example.com *.example Server Block: server { listen 80; server_name subdomain.example.com; access_log /srv/www/subdomain.example.com/logs/access.log; error_log /srv/www/subdomain.example.com/logs/error.log; root /srv/www/subdomain.example.com/public_html; location / { index index.html index.htm index.php; } location ~ \.php$ { include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I've created the system link to the file in the /etc/nginx/sites-enabled/ directory and restarted/reloaded nginx. DNS seems fine: # ping -c 2 subdomain PING subdomain.example.com (xxx.xxx.xx.xxx) 56(84) bytes of data. 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=1 ttl=64 time=0.035 ms 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=2 ttl=64 time=0.048 ms Checking the file with cURL works: # curl http://subdomain.example.com HTML - OK Emptied browser cache but still no dice. Anything I'm missing? Like I mentioned, I have a few sites running fine on the server currently so php-fpm etc etc are working. Any help would be much appreciated! Cheers, Dave

  Read the article

• Windows Server doesn't connect to a network share

  - by Dmitriy N. Laykom

  Windows Server doesn't connect to a network share. Network share is working. Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When I connected the network share I observed this error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location The network share was mounted via Group Policy. Perchance anyone knows how I can avoid this error? When the OS has been restored from the disk problem has been solved

  Read the article

• Debian grub2 update removed Windows boot option.

  - by Wrikken

  Since I updated grub to grub 2 I no longer get the option to boot to Windows (which is unfortunately sometimes necessary for proprietary MSIE browser plugins I need to use for work). Relevant /boot/grub/menu.lst portion: ### END DEBIAN AUTOMAGIC KERNELS LIST # This is a divider, added to separate the menu items below from the Debian # ones. title Other operating systems: root # This entry automatically added by the Debian installer for a non-linux OS # on /dev/hda1 title Windows NT/2000/XP root (hd0,0) savedefault makeactive chainloader +1 This however does not appear anymore. I do have some entries in /boot/grub/grub.cfg with entries like these: menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod part_msdos insmod ext2 set root='(hd1,msdos1)' search --no-floppy --fs-uuid --set e638c434-4884-412f-a141-2c194f881fae echo 'Loading Linux 2.6.32-5-amd64 ...' linux /boot/vmlinuz-2.6.32-5-amd64 root=UUID=e638c434-4884-412f-a141-2c194f881fae ro quiet echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-2.6.32-5-amd64 } Do I have to alter that file? If so, what is the correct syntax for a Windows boot? If not, what could be the problem?

  Read the article

• Can't Connect SQL server - process being used by another process. Conflict with IIS?

  - by shinya

  I'm having problem connecting to MS SQL Server (2012 Express) after accessing a database through IIS (web site). I can access the data through web site no problem, but I can't access the data from any other programs (i.e SSMS) until I reboot the SQL server. It seems that the connection stays open even if I close a browser. Here is error message I'm getting Unable to open the physical file "C:---------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Unable to open the physical file "C:-------". Operating system error 32: "32(The process cannot access the file because it is being used by another process.)". Cannot open user default database. Login failed. Login failed for user 'Myserver\myname'. (.Net SqlClient Data Provider) Server Name: MYPC\SQLEXPRESS Error Number: 5120 Severity: 16 State: 101 Line Number: 65536 I follow the help link and it told me to move TCP before named pipes in the protocol order list. I tried it but it didn't help at all. What is the proper settings on SQL server or IIS in order to release process after closing a browser. How do I avoid getting this error? Thank you for your help

  Read the article

• LVS / IPVS difference in ActiveConn since upgrading

  - by Hans

  I've recently migrated from an old version of LVS / ldirectord (Ultra Monkey) to a new Debian install with ldirectord. Now the amount of Active Connections is usually higher than the amount of Inactive Connections, it used to be the other way around. Basically on the old load balancer the connections looked something like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 12 252 -> 10.84.32.22:0 Masq 1 18 368 However since migrating it to the new load balancer it looks more like: -> RemoteAddress:Port Forward Weight ActiveConn InActConn -> 10.84.32.21:0 Masq 1 313 141 -> 10.84.32.22:0 Masq 1 276 183 Old load balancer: Debian 3.1 ipvsadm 1.24 ldirectord 1.2.3 New load balancer: Debian 6.0.5 ipvsadm 1.25 ldirectord 1.0.3 (I guess the versioning system changed) Is it because the old load balancer was running a kernel from 2005, and ldirectord from 2004, and things have simply changed in the past 7 - 8 years? Did I miss some sysctl settings that I should be enforcing for it to behave in the same way? Everything appears to be working fine but can anyone see an issue with this behaviour? Thanks in advance! Additional info: I'm using LVS in masquerading mode, the real servers have the load balancer as their gateway. The real servers are running Apache, which hasn't changed during the upgrade. The boxes themselves show roughly the same amount of Inactive Connections shown in ipvsadm.

  Read the article

• On Ubuntu get: "-bash: ./flume No such file or directory" BUT flume is there and executable. Same binary OK on RHEL

  - by lcbrevard

  This is already posted in serverfault - and may be more apprpriate there. Reworked a bit from the orginal posting. We have a product built on CentOS 4 32-bit Linux that runs unmodified on 32- and 64-bit CentOS/RHEL 4 and 5 and SLES 10. It also runs unmodified on SLES 9 64-bit. [SLES 9 32-bit requires a different libstdc++.] The name of the main binary executable is 'flume' Yesterday we tried to put this on 64-bit Ubuntu 10 and, even though the file is there and the right size, we get: -bash: ./flume: No such file or directory 'file flume' shows it to be a 32-bit ELF (can't remember the exact output and the system is on an isolated network) If put into /usr/local/bin, then 'which flume' returns: /usr/local/bin/flume The file is marked as executable (did 'chmod +x flume') and lsattr shows no problems with attribute bits. I was not able to try 'ldd flume' yet. I have also not tried 'strace flume'. Currently I am with an air conditioning failure. [It's been that kind of week!] I now suspect that some library is not there. This is a profoundly unhelpful message and one I have never seen before. Is this peculiar to Ubuntu or perhaps just to this installation. We gave up and moved to a RHEL 4 system and everything is fine. But I sure would like to know what causes this.

  Read the article

• Windows Server don't connect to network share

  - by user104775

  Windows Server don't connect to network share. Network share is work. Ping Blockquote Pinging 109.123.146.223 with 32 bytes of data: Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Reply from 109.123.146.223: bytes=32 time<1ms TTL=63 Ping statistics for 109.123.146.223: Packets: Sent = 3, Received = 3, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms net view \shareaddress Blockquote System error 53 has occurred. The network path was not found. When network share was connected, I was got a error message: Blockquote \ "Mapped disk letter" refers to a location that is unavailable. It could be on a hard drive on this computer, or on a network. Check to make sure that the disk is properly inserted, or that you are connected to the Internet or your network, and then try again. If it still cannot be located, the information might have been moved to a different location Network share mounted via Group Policy. Any ideas?

  Read the article

• Notepad and Regedit does not launch from C:\Windows or C:\Windows\System32, but will from C:\Windows\SysWOW64

  - by lordhog

  My work machine was recently updated from Windows XP 64-bit to Windows 7 64-bit. I have found a few odd things that I can not figure out why they are occurring. If I type in Notepad.exe or RegEdit.exe from the Run diaglog the applications will not launch. When executing RegEdit.exe from the Run dialog the UAC does display asking for admin privileges, but the application never launches. Also, if I go to the Start menu and click on Notepad from there, Notepad never launches either. Other programs seem to be okay, like mspaint, wordpad, etc. Now, if I launch Notepad or RegEdit from C:\Windows\SysWOW64 then these applications will run, though I think these are the 32-bit version and not the 64-bit version. I am not sure what is going on. Has anyone seen this behavior before and how to fix it? I have Windows 7 64-bit at home and I don't have this issue. I even copied Notepad.exe from home and place it in the C:\ folder and tried to launch it from there and it still doesn't work. Regards, Mark

  Read the article

< Previous Page | 229 230 231 232 233 234 235 236 237 238 239 240  | Next Page >