Search Results

Search found 1080 results on 44 pages for 'connectivity'.

Page 24/44 | < Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >

  • SSL client auth in nginx with multiple server section

    - by Bastien974
    I want to implement ssl_verify_client in nginx. This works perfectly when I only have one server section, which listen to 443. In my case I have multiple, all listening on 443 but to different server_name. For one particular server (proxy.mydomain.com), I'm adding the SSL client verify, but when I test the connectivity with openssl s_client -connect proxy.mydomain.com:443 -cert xxx.crt -key xxx.key and then do a GET / HTTP/1.1 host: proxy.mydomain.com It's not working, 400 No required SSL certificate was sent I think nginx is not receiving the proper server_name and is directing it to the first server listening to 443. So I tried to listen on another port and it worked right away. What's the issue and how can I fix it ?

    Read the article

  • Computer never connects to the internet automatically on startup?

    - by RawR Crew
    I have my Windows Vista laptop connected directly to the router via an ethernet cable, and every time I switch the computer on, the computer cannot connect to the internet. It comes up as limited or no connectivity, I am assuming because it has not been assigned an IP address by the router - not too sure if this is right. The problem is usually fixed either by performing a repair through the networking control panel or removing and re-inserting the ethernet cable. It will also connect without doing any of these if the computer is left idle for about 20 minutes. It will connect fine wirelessly without the need for any of this, however I would prefer to connect via the cable. Any ideas how I can fix this? I have replaced the ethernet cable and router already (identical model) but these haven't helped. Thanks for any help on this.

    Read the article

  • Can send to individual users but not when they are in a global distribution list.

    - by Jake
    I am able to send email to individual users but when not when they are in a distribution group. When I do I get this report. The message could not be delivered because the recipient's destination email system is unknown or invalid. Please check the address and try again, or contact your system administrator to verify connectivity to the email system of the recipient. #5.3.1 However, like I said before I can select their name from the GAL and send mail that way. Their email address is exactly the same in both the GAL and distribution group. The only difference is these users have external email addresses. Windows Server 2003 Exchange Server 2003 Outlook 2007 and 2010.

    Read the article

  • Linksys Wireless-N ADSL2 WAG160N losing connection

    - by Sam1973
    It seems that recently I have to turn off and then turn on my router every time I want to connect my laptop(s) to the internet. This is what's happens: When I want to connect to the internet on my laptop, the network icon in the system tray states that I am connected to the wireless network but there's no "internet connectivity" I turn off the router and turn it back on and then I can connect to the internet. I am sure there is something that needs to be done. Can you guys point me to the right direction?

    Read the article

  • OpenVPN client on Amazon EC2

    - by Matt Culbreth
    I have an account with an OpenVPN service, and I'd like to get that running on my EC2 instance running Ubuntu 12.04. I have my config file in /etc/openvpn, and it connects fine when I run sudo openvpn --config matt.ovpn. However, I then lose connectivity to the EC2 machine, and I can't SSH back to it until I reboot. Previously I have done things like sudo ip rule add from IP_ADDRESS table 10 and then sudo ip route add default via GATEWAY_IP table 10, but that's not working on EC2. Any ideas? My private IP address right now is 10.209.29.XXX and my gateway is 10.209.29.1.

    Read the article

  • vmware workstation - virtual network adapters missing from ipconfig, still show in networking (XP host)

    - by Adam
    Hi Folks - here's a new one for me, and my first time posting here: I installed VMWare workstation 7.1 on a new PC. VMWare properly installs the virtual network adapters under the Network Connections control panel, however for some reason they do not show up under ipconfig, which is very weird. They also don't appear anywhere in "route print". I don't have network connectivity to the VM. My guesses are perhaps some conflict with Symantec AntiVirus or Symantec Client Firewall. Tried the following things: enabling TCP/IP in the virtual network adapters (they often get installed with it disabled for some reason) Restoring defualts in the VMnetcfg gui tool (this causes an uninstall and reinstall of the virtual network adapters on the host) Re-installing vmware workstation Uninstalling checkpoint secureremote and then reinstalling vmware Just to be clear, this problem is totally on the host. In my searching for stuff about (non-vmware) adapters missing from ipconfig, I see some posts about resetting the TCP/IP stack using netsh. Looking into that next... Thanks!

    Read the article

  • MSSQL: Choice of service accounts

    - by Troels Arvin
    When installing MS SQL Server 2008, one needs to associate a service account with the installation (possibly even several accounts, one for the SQL Server Agent, one for Analysis Services, ..., but let's leave that for the case of simplicity). The service account may be local account, or a Windows domain account. If a domain account is used: Can MSSQL start, if connectivity to the domain controllers is temporarily down? If the answer is yes: Should each DBMS instance on each server have a separate account, or does it make sense to use a particular "MSSQL" domain account on all MSSQL-installations in the organization? If separate accounts are used for each instance on each server: Does it make sense to create a special MSSQL security group in the domain and place all the MSSQL service accounts in that group, perhaps to ease replication, etc? Is there a common, generally accepted naming convention for MSSQL service account(s)?

    Read the article

  • Getting VPN to work from Virtual PC

    - by strobaek
    Setup: Host is running Windows7. Virtual PC is a Windows Server 2008 running under VMWare workstation 6.5. From the Host I have a VPN to e.g. TFS and other resources. From the VPC I need to connect to e.g. a SQL server via the VPN. My problem is, that I cannot get a connection from the VPC. If I'm sitting on the corporate network, all is working fine (but then I don't have the VPN). From home - where the VPN is required - it does not work. I have two network adapters defined/configued. One as BRIDGED and one as Host Only. IF I change the one being BRIDTED to NATS I have no connectivity at all from the VPC. I have no problems connecting from my host to the VPC. Thanks.

    Read the article

  • Windows Media Center won't Play MSN Video Player

    - by Chris Spicer
    My install of Windows Media Center won't play MSN Video Player videos. They appear in the main guide, but when I click on them, nothing happens. If I look on the main menu, I don't have any icons for MSN Video player there. People have suggested I try downloading updates, but that makes no difference. I have internet connectivity. My region is set to the UK (which is where I am). If I navigate to the MSN Video Player using Internet Explorer, the videos play fine. The machine is an Acer Revo RL100, running Windows 7 64-bit. Does anyone have a solution for this? Any help would be gratefully received.

    Read the article

  • How do I configure networking on CentOS 6 running on hyper-v?

    - by LonelyLonelyNetworkN00b
    I'm not using legacy adapters, and i've installed Linux Integration Components 3.2. THe problem i'm facing is that the command 'setup' or 'system-config-network' doesn't list any network interfaces. If i run ifconfig -a i can see both the network cards i've attached. By setting a ip using ifconfig i can get network connectivity. The problem is that it's not persistent after a reboot. I'm a 100% centos newbie, but I figure it has something to do with that the centos installer couldn't see the NICs on install. How can I fix this?

    Read the article

  • Connecting office to data center via Metro-ethernet

    - by Eric
    I am installing a metro ethernet link from my office to my data center. The office will have a cisco 3750 with several vlans. The data center end will have a more complicated set up. The metro e from the office will connect to a 2960, which will have two other 2960s with a few vlans and a 2811 router connected to it for connectivity to our other environments and the internet. I am looking at implementing this by connecting the office 3750 and the data center 2960 with a dot1q trunk and doing all routing at the 2811. I will configure subinterfaces for gateways for each of the vlans on the 2811. I work for a small company and don't have much of a budget for an ideal architecture. I can post a simple diagram if needed for clarification. Is there anything I am missing here? I feel like I am forgetting something very basic and want to make sure I eliminate any boneheaded mistakes.

    Read the article

  • Enable/disable wireless interface in a bat file

    - by Herms
    Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

    Read the article

  • Only ONE Outlook 2010 installation "Cannot connect to Exchange server" when setting up new profile.

    - by Johnny PDEX
    Exchange 2010, one-server installation (small production, I know not best practice) OWA Connectivity has been confirmed, Autodiscover is configured and working properly for EVERY other installation. Other user accounts tested on problem Outlook, none can connect. Windows Firewall is pre-configured by Group Policy, only modifications being related to remote management. Firewall has also been disabled during diagnostic period. Network discovery and file sharing is enabled on workstation as well. Windows 7 Professional, latest updates installed. Driving me nuts. Help, serverfault?

    Read the article

  • Cannot connect to internet with Clearwire modem.

    - by ide
    I'm currently using a Motorola WiMAX modem (CPEi 25725) and cannot connect to the internet. I can connect to the modem at 192.168.15.1 and check its status. It says that it has good/excellent connectivity to the internet and shows all five signal bars. Additionally it has sent and received some WiMAX packets so I believe it is connected to a tower. I'm at a loss for what the problem is. Unplugging the modem, restarting it from software, and restarting my computer (Windows 7) have not helped. Windows still reports that it is not connected to the internet. Alternatively, could this be an ISP issue? I have heard that Clearwire is a not-so-reputable ISP that blocks VoIP, and I was using Skype recently.

    Read the article

  • HTTP, HTTPS and FTP is not working but SMTP and IMAP are working.

    - by nWorx
    Yesterday on a computer of a friend a strange thing happened. after booting the ports fo http, https and ftp are closed but e-mail is still working. in the control panel the windows firewall seems active even if he tries to deactivate it. I have a suspision that it is the faul of norton internet security 2010, we have tried to uninstall it, but the uninstallation did not work. when using the removal tool from symantec it just goes to 23% and then it crashes. the process ccSvcHst.exe is still running. How can I safely remove the rest of Norton Internet Security? Edit: Norton Internet Security 2010 is sucesfully removed, but still no connectivity...

    Read the article

  • wifi connection turns off oll the time

    - by er-v
    Hello! I realy need help with one strange problem. I have a wifi network in my appartment with wireless N home router Trendnet tew-652BRP. Everething work fine for three of my laptops, but I have one PC with D-Link DWA-140 adapter. It looses connection 2-3 times in 5 minutes. There is following messages in my system log when it does so: The browser has forced an election on network \Device\NetBT_Tcpip_{9537A5C1-3B43-4C56-B94C-CE69A257C3AD} because a master browser was stopped. The TCP/IP NetBIOS Helper service was successfully sent a stop control. The reason specified was: 0x40030011 [Operating System: Network Connectivity (Planned)] Comment: None The TCP/IP NetBIOS Helper service entered the stopped state. in order of appearence. How can I stop it? I have the latest driver installed.

    Read the article

  • Is there a way to reliably backup and restore a complex network configuration on Windows XP?

    - by djangofan
    I have some Windows XP laptops (10+) that host a ad-hoc WIFI network connection to wireless PDA devices. The laptop itself is connected via a 3rd party VPN radio network. The radio network itself seems to be reliable. If one small thing goes wrong with the network configuration then the PDA loses connectivity and so I need a way to backup a networking config , either via a script or a 3rd party program, so that I can restore a working network configuration if something goes wrong. Is this possible? Does anyone have any ideas?

    Read the article

  • Routing using Linux with 2 NIC cards

    - by Kevin Parker
    Configured Clear OS to be in Gateway mode on a machine with two NIC cards. eth0:192.168.2.0/24 with ip 192.168.2.27 which is connected to a modem and thus have internet connectivity. eth1:192.168.122.0/24 with ip 192.168.122.10 which is connected to other machines in LAN through switch. LAN machines with network 192.168.122.0 is not getting internet.How can they get internet Through Clear OS gateway.I have enabled packet forwarding in clear os using "ip_forward=1" What am i missing?.Can you please help me in this. Following are the static routing i have added: on LAN machine1 with ip address 192.168.122.11 ip route add 192.168.2.0/24 via 192.168.122.10 dev eth0 ip route show 192.168.2.0/24 via 192.168.122.10 dev eth0 192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.11 But still 192.168.2.0/24 network is not reachable.Where can be the problem??

    Read the article

  • BES 5.x issues when connecting to Exchange 2010 SP2 RU4

    - by makerofthings7
    Ever since we updated from SP1 RU4 to SP2 RU4 we have noticed that our BES devices will simply stop receiving email. This has occurred at least 5 times in the past few weeks. Today, while speaking with RIM support (a T3 contract), they said that they have reports of sporadic connectivity issues from some BES users. This has been occurring with Exchange 2010 SP2 RU4, and have no public information to give us. We were able to temporarily get things running by doing any or all of the following Restart the BES server Recreate the MAPI profile (deleted the keys in the registry) Restart the CAS servers Wait it out (2 hours) What other options should I take to resolve this issue?

    Read the article

  • Automatically reboot Windows8 if no internet activity [migrated]

    - by Patrick
    I have a media server located in a very inconvenient part of my house. Occasionally I will have to reset my router or it will reset itself. The issue is the PC loses connectivity for some reason, and I am forced to walk outside, around the house, into the basement, over a bunch of toys and weights and boxes, to push a button to reboot it. I would love to have it check itself every 5-10 minutes and auto reboot if it is unable to ping a given address/IP. Any ideas how to accomplish this?

    Read the article

  • Is it possible to use a static IP assigned by my ISP for an offsite web server on a VPS (different ISP)?

    - by NightOwl888
    I have a web server on a Virtual Private Server with a hosting provider. Unfortunately, they are really stingy with IP addresses and I need to run several SSL certificates on my server, so I will need a few more than I have. I have a block of 5 static IP addresses on a business package through a different ISP and I am only using 1 of them for connectivity in the office. What I am wondering is if it is possible to use the 4 unused static IP addresses from this ISP on my VPS, which is hosted by another ISP? The VPS (web server) is running Windows Server 2008 R2 Web Edition. If this can be done, please let me know how to configure it.

    Read the article

  • Cisco access list logging. Why is there a difference between IPv4 and IPv6?

    - by growse
    I've got a Cisco 877 router. I've got an IPv4 access list and an IPv6 access list set up and configured similar to this: interface Dialer1 ... ip access-group INTERET-IN ipv6 traffic-filter IPV6-IN Each of these access lists has a final rule of deny ip/ipv6 any any log. However, in my syslog I notice that there's a difference in formatting between the two types of entries. IPv4 will say: %SEC-6-IPACCESSLOGP: list INTERNET-IN denied udp 88.89.209.63(137) -> 1.2.3.4(137), 1 packet Whereas the IPv6 list will say %IPV6_ACL-6-ACCESSLOGNP: list IPV6-IN/240 denied 59 2001:0:5EF5:79FD:14F9:B773:3EBA:3EE3 (Dialer1) -> 2001:800:1000:0::1, 8 packets Both have broadly the same information, but the IPv6 log entry is missing the protocol type and port, both of which are very useful if I'm trying to troubleshoot connectivity. Why is this? How do I get IPv6 deny logs to display the protocol and port used, if any?

    Read the article

  • Long lag and errors clicking gmail links in google chrome

    - by Doug T.
    I recently downloaded Google Chrome with Ubuntu 9.04 and love it. Ironically one site I consistently have issues with is gmail. When I enter gmail I will click a link, say an email or the inbox link. After a very long wait (on the order of 30 seconds to a couple of minutes) my page will load with an error such as: Some Gmail features have failed to load due to an Internet connectivity problem. If this problem persists, try reloading the page, using the older version, or using basic HTML mode. Learn More. Googling the symptoms has not helped. Has anyone else had any similar issues? Has anything helped?

    Read the article

  • No internet access on Windows 7 - part 2

    - by Vnuk
    This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

    Read the article

  • Computer Loses connection to router

    - by ajon
    I have a new Windows 8 Dell XPS desktop computer at work. It has a Dell Wireless 1703 802.11 b/g/n (2.4ghz) wireless adapter. sporadically throughout the day I lose internet connectivity. When I click on the wireless system tray icon, my companies router does not appear in the list. No other computer on the network is losing connection, only this one. I don't even know what to check. Could it be an ip conflict that causes me to get booted off? (I use DHCP), but why wouldn't my computer be able to see the network. The next time it happens I will see what happens when I try to access the router directly.

    Read the article

< Previous Page | 20 21 22 23 24 25 26 27 28 29 30 31  | Next Page >