Search Results

Search found 8649 results on 346 pages for '15 puzzle'.

Page 242/346 | < Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >

• Wireless is detected, but not connecting. Ethernet works. How to correct the wireless address?

  - by Lucas

  I am running Ubuntu 14.04 with cable internet, and my wireless is detected and connected, but I cannot connect to the internet. I know the problem is with my machine because other machines are connecting to the same router just fine. I can connect via ethernet just fine as well. Here are some notable tests: ping 192.168.0.105 works with 0% packet loss, but ping 192.168.0.1 has 100% packet loss. When I plug in my ethernet, ping 192.168.0.1 works with 0% packet loss. My wireless name is tg, and the router ip is 192.168.0.1 (where I can enter username and password). I suspect that I need to change my wireless address from 192.168.0.105 to 192.168.0.1. Any suggestions on how to proceed? extra info: [lucas@lucas-ThinkPad-W520]/home/lucas$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"tg" Mode:Managed Frequency:2.462 GHz Access Point: 00:02:6F:83:F8:F4 Bit Rate=1 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:52 Invalid misc:166 Missed beacon:0 [lucas@lucas-ThinkPad-W520]/home/lucas$ ifconfig eth0 Link encap:Ethernet HWaddr f0:de:f1:b2:53:53 inet addr:192.168.0.100 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::f2de:f1ff:feb2:5353/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:980003 errors:0 dropped:0 overruns:0 frame:0 TX packets:498384 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1320506168 (1.3 GB) TX bytes:59780591 (59.7 MB) Interrupt:20 Memory:f3a00000-f3a20000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:21927 errors:0 dropped:0 overruns:0 frame:0 TX packets:21927 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1781719 (1.7 MB) TX bytes:1781719 (1.7 MB) wlan0 Link encap:Ethernet HWaddr 24:77:03:29:8f:dc inet addr:192.168.0.105 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::2677:3ff:fe29:8fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:11828 errors:0 dropped:0 overruns:0 frame:0 TX packets:15444 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4855662 (4.8 MB) TX bytes:2250585 (2.2 MB) [lucas@lucas-ThinkPad-W520]/home/lucas$ lspci -nn | grep 0280 03:00.0 Network controller [0280]: Intel Corporation Centrino Ultimate-N 6300 [8086:4238] (rev 3e) [lucas@lucas-ThinkPad-W520]/home/lucas$ rfkill list 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no with ethernet unplugged: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 wlan0 with ethernet plugged in: [lucas@lucas-ThinkPad-W520]/home/lucas$ route -n | grep UG 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 [lucas@lucas-ThinkPad-W520]/home/lucas$ nm-tool NetworkManager Tool State: connected (global) - Device: wlan0 [tg] ---------------------------------------------------------- Type: 802.11 WiFi Driver: iwlwifi State: connected Default: no HW Address: 24:77:03:29:8F:DC Capabilities: Speed: 52 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) tatum: Infra, 40:8B:07:D8:A5:04, Freq 2437 MHz, Rate 54 Mb/s, Strength 42 W PA WPA2 ums: Infra, 00:20:A6:72:52:BF, Freq 2437 MHz, Rate 54 Mb/s, Strength 59 Alpha 40: Infra, 28:CF:E9:86:59:5D, Freq 5260 MHz, Rate 54 Mb/s, Strength 30 W PA WPA2 thepromiselan: Infra, 58:6D:8F:51:E5:54, Freq 2452 MHz, Rate 54 Mb/s, Strength 34 $ PA WPA2 xfinitywifi: Infra, 06:1D:D5:84:27:A0, Freq 2437 MHz, Rate 54 Mb/s, Strength 52 *tg: Infra, 00:02:6F:83:F8:F4, Freq 2462 MHz, Rate 54 Mb/s, Strength 73 W PA2 ums: Infra, 00:20:A6:A1:9F:25, Freq 2452 MHz, Rate 54 Mb/s, Strength 44 BRIAN-PC_Network:Infra, 20:AA:4B:DD:93:D6, Freq 2462 MHz, Rate 54 Mb/s, Strength 35 W PA2 HOME-C0F8: Infra, 44:32:C8:D2:C0:F8, Freq 2412 MHz, Rate 54 Mb/s, Strength 40 W PA WPA2 abcsexy: Infra, 28:28:5D:27:5D:85, Freq 2412 MHz, Rate 54 Mb/s, Strength 27 W PA WPA2 IPv4 Settings: Address: 192.168.0.105 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: e1000e State: connected Default: yes HW Address: F0:DE:F1:B2:53:53 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.0.100 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1

  Read the article

• Using the latest (stable release) of Oracle Developer Tools for Visual Studio 11.1.0.7.20.

  - by mbcrump

  +  = Simple and safe Data connections.   This guide is for someone wanting to use the latest ODP.NET quickly without reading the official documentation. This guide will get you up and running in about 15 minutes. I have reviewed my referral link to my simple Setting up ODP.net with Win7 x64 and noticed most people were searching for one of the following terms: “how to use odp.net with vs” “setup connection odp.net” “query db using odp and vs” While my article provided links and a sample tnsnames.ora file, it really didn’t tell you how to use it. I’m hoping that this brief tutorial will help. So before we get started, you will need the following: Download the following: www.oracle.com/technology/software/tech/dotnet/utilsoft.html from oracle and install it. It is the first one on the page. Visual Studio 2008 or 2010. It should be noted that The System.Data.OracleClient namespace is the OLD .NET Framework Data Provider for Oracle. It should not be used anymore as it has been depreciated. The latest version which is what we are using is Oracle.DataAccess.Client. First things first, Add a reference to the Oracle.DataAccess.Client after you install ODP.NET   Copy and paste the following C# code into your project and replace the relevant info including the query string and you should be able to return data. I have commented several lines of code to assist in understanding what it is doing.   Lambda Expression. using System; using System.Data; using Oracle.DataAccess.Client;   namespace ConsoleApplication1 {     class Program     {         static void Main(string[] args)         {           try         {             //Setup DataSource             string oradb = "Data Source=(DESCRIPTION ="                                    + "(ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)(HOST = hostname)(PORT = 1521)))"                                    + "(CONNECT_DATA = (SERVICE_NAME = SERVICENAME))) ;"                                    + "Persist Security Info=True;User ID=USER;Password=PASSWORD;";                        //Open Connection to Oracle - this could be moved outside the try.             OracleConnection conn = new OracleConnection(oradb);             conn.Open();               //Create cmd and use parameters to prevent SQL injection attacks.             OracleCommand cmd = new OracleCommand();             cmd.Connection = conn;               cmd.CommandText = "select username from table where username = :username";               OracleParameter p1 = new OracleParameter("username", OracleDbType.Varchar2);             p1.Value = username;             cmd.Parameters.Add(p1);               cmd.CommandType = CommandType.Text;               OracleDataReader dr = cmd.ExecuteReader();             dr.Read();               //Contains the value of the datarow             Console.WriteLine(dr["username"].ToString());               //Disposes of objects.             dr.Dispose();             cmd.Dispose();             conn.Dispose();         }           catch (OracleException ex) // Catches only Oracle errors         {             switch (ex.Number)             {                 case 1:                     Console.WriteLine("Error attempting to insert duplicate data.");                     break;                 case 12545:                     Console.WriteLine("The database is unavailable.");                     break;                 default:                     Console.WriteLine(ex.Message.ToString());                     break;             }         }           catch (Exception ex) // Catches any error not previously caught         {                   Console.WriteLine("Unidentified Error: " + ex.Message.ToString());              }         }       }           } At this point, you should have a working Program that returns data from an oracle database. If you are still having trouble then drop me a line and I will be happy to assist. As of this writing, oracle has announced the latest beta release of ODP.NET 11.2.0.1.1 Beta.  This release includes .NET Framework 4 and .NET Framework 4 Client Profile support. You may want to hold off on this version for a while as its BETA, and I wouldn’t want any production code using any BETA software.

  Read the article

• Integrated webcam in lenovo t410 not working with 12.04

  - by kristianp

  I have a Lenovo T410 with an inbuilt webcam and I haven't been able to get the webcam working. I tried skype, cheese, both just give me a black window. The microphone works fine with skype, by the way. Can anyone provide any clues please? The webcam is enabled in the bios, but there is no light indicating the webcam is on (not sure if there should be, though). I tried this on Kubuntu 11.10 and have upgraded to 12.04 with the same results. The Fn-F6 keyboard combination doens't seem to do anything either. EDIT: I got the webcam replaced, it looks like it was a hardware problem, because it works fine now. Thanks guys. $ ls /dev/v4l/* /dev/v4l/by-id: usb-Chicony_Electronics_Co.__Ltd._Integrated_Camera-video-index0 /dev/v4l/by-path: pci-0000:00:1a.0-usb-0:1.6:1.0-video-index0 And lsusb: $ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 003: ID 147e:2016 Upek Biometric Touchchip/Touchstrip Fingerprint Sensor Bus 001 Device 004: ID 0a5c:217f Broadcom Corp. Bluetooth Controller Bus 001 Device 005: ID 17ef:480f Lenovo Integrated Webcam [R5U877] Bus 002 Device 003: ID 05c6:9204 Qualcomm, Inc. Bus 002 Device 004: ID 17ef:1003 Lenovo Integrated Smart Card Reader Here is the output from guvcview, minus lots of lines describing the available capture formats. It says "unable to start with minimum setup. Please reconnect your camera.". guvcview 1.5.3 ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.rear ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.center_lfe ALSA lib pcm.c:2217:(snd_pcm_open_noupdate) Unknown PCM cards.pcm.side ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib audio/pcm_bluetooth.c:1614:(audioservice_expect) BT_GET_CAPABILITIES failed : Input/output error(5) ALSA lib pcm_dmix.c:957:(snd_pcm_dmix_open) The dmix plugin supports only playback stream ALSA lib pcm_dmix.c:1018:(snd_pcm_dmix_open) unable to open slave Cannot connect to server socket err = No such file or directory Cannot connect to server socket jack server is not running or cannot be started video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } Time interval between frame: 1/30, .... { discrete: width = 1600, height = 1200 } Time interval between frame: 1/15, vid:17ef pid:480f driver:uvcvideo checking format: 1196444237 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! Init video returned -2 trying minimum setup ... video device: /dev/video0 Init. Integrated Camera (location: usb-0000:00:1a.0-1.6) { pixelformat = 'YUYV', description = 'YUV 4:2:2 (YUYV)' } { discrete: width = 640, height = 480 } .... vid:17ef pid:480f driver:uvcvideo checking format: 1448695129 libv4l2: error setting pixformat: Device or resource busy VIDIOC_S_FORMAT - Unable to set format: Device or resource busy Init v4L2 failed !! ERROR: Minimum Setup Failed. Exiting... VIDIOC_REQBUFS - Failed to delete buffers: Invalid argument (errno 22) cleaned allocations - 100% Closing portaudio ...OK Terminated.

  Read the article

• Should I break contract early?

  - by cbang

  About 7 months ago I made the switch from a 5 year permie role (as a support developer in C#) to a contract role. I did this because I was stagnating in my old role. The extra cash contracting is really helping too. Unfortunately my team leader has taken a dislike to me from day 1. He regularly tells me I went out contracting too early, and frequently remarks that people in their 20's have no idea what they are talking about (I am 29). I was recently given the task of configuring our reports via our in house reporting library. It works off of a database driven criteria base, with controls being loaded as needed. The configs can get fairly complex, with controls having various levels of dependency on each other. I had a short time frame to get 50 reports working, and I was told to just get the basic configuration done, after which they will be handed over to the reporting team for fine tuning, then the test team. Our updated system was deployed 2 weeks ago, and it turned out that about 15 reports had issues causing incorrect data to be returned. Upon investigation I discovered that the reporting team hadn't even looked at them, and the test team hadn't bothered to test the reports. In spite of this, my team leader has told me that it is 100% my fault. As a result, our help desk got hit hard. I worked back until 2am that night to fix the highest priority issues (on my wedding anniversary!). The next day I arrive at work at 7:45 am to continue with the fixes. I got no thanks, but keep getting repeatedly told by my manager that "I fucked up" and "this is all my fault". I told my team leader I would spend part of my weekend working to fix the remaining issues. His response was "so you fucking should! you fucked it all up!" in front of the rest of the team. I responded "No worries." and left. I spent a decent chunk of my weekend working on it. Within 2 business days of finding out about the issues, I had all the medium and high priority issues fixed. The only comments my team leader has made to me in the last 2 weeks is to tell me how I have caused a big mess, and to tell me it was all my fault. I get this multiple times a day. If I make any jokes to anyone else in the team, I get told not to be a smartass... even though the rest of the team jokes throughout the day. Apart from that, all I get is angry looks any time I am anywhere near the guy. I don't give any response other than "alright" or silence when he starts giving me a hard time. Today we found out that the pilot release for the next stage has been pushed back. My team leader has said this was caused by me (but the higher ups said no such thing). He also said I have "no understanding of the ramifications of my actions". My question is, should I break contract (I am contracted until June 30) and find another role? No one else in my team will speak up in my favour, as they are contractors too and have no interest in rocking the boat. I could complain to my team leaders boss, but I can't see that helping, as I will still be stuck in the same team. As this is my first contract, I imagine getting the next one will be hard without a reference. I can't figure out if this guy is trying to get me fired up to provoke a confrontation (the guy loves conflict), or if he is just venting anger, or what. Copping this blame day after day is really wearing me down and making me depressed... especially since I have a wife and kid to support).

  Read the article

• How to get bearable 2D and 3D performance on AMD Radeon HD 6950?

  - by l0b0

  I have had an AMD Radeon HD 6950 (i.e., Cayman series) for a couple years now, and I have tried a lot of combinations of drivers and settings with terrible results. I'm completely at a loss as to how to proceed. The open source driver has much better 2D performance, but it offloads all OpenGL rendering to the CPU. What I've tried so far: All the latest stable Ubuntu releases in the period, plus one Linux Mint release. All the latest stable AMD Catalyst Proprietary Display Drivers, and currently 13.1. The unofficial wiki installation instructions for every Ubuntu version and the semi-official Ubuntu instructions. All the tips and tweaks I could find for Minecraft (Optifine, reducing settings to minimum), VLC (postprocessing at minimum, rendering at native video size), Catalyst Control Center (flipped every lever in there) and X11 (some binary toggles I can no longer remember). Results: Typically 13-15 FPS in Minecraft, 30 max (100+ in Windows with the same driver version). Around 10 FPS in Team Fortress 2 using the official Steam client. Choppy video playback, in Flash and with VLC. CPU use goes through the roof when rendering video (150% for 1080p on YouTube in Chromium, 100% for 1080p H264 in VLC). glxgears shows 12.5 FPS when maximized. fgl_glxgears shows 10 FPS when maximized. Hardware details from lshw: Motherboard ASUS P6X58D-E CPU Intel Core i7 CPU 950 @ 3.07GHz (never overclocked; 64 bit) 6 GB RAM Video card product "Cayman PRO [Radeon HD 6950]", vendor "Hynix Semiconductor (Hyundai Electronics)" 2 x 1920x1200 monitors, both connected with HDMI. I feel I must be missing something absolutely fundamental here. Is there no accelerated support for anything on 64-bit architectures? Does a dual monitor completely mess up the driver? $ fglrxinfo display: :0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: AMD Radeon HD 6900 Series OpenGL version string: 4.2.11995 Compatibility Profile Context $ glxinfo | grep 'direct rendering' direct rendering: Yes I am currently using the open source driver, with the following results: Full frame rate and low CPU load when playing 1080p video. Black screen (but music in the background) in Team Fortress 2. Similar performance in Minecraft as the Catalyst driver. In hindsight obvious, since both end up offloading the rendering to the CPU. My /var/log/Xorg.0.log after upgrading to AMD Catalyst 13.1. Some possibly important lines: (WW) Falling back to old probe method for fglrx (WW) fglrx: No matching Device section for instance (BusID PCI:0@3:0:1) found The generated xorg.conf. The disabled "monitor" 0-DFP9 is actually an A/V receiver, which sometimes confuses the monitor drivers when turned on/off (but not in Windows). All three "monitor" devices are connected with HDMI. Edit: Chris Carter's suggestion to use the xorg-edgers PPA (Catalyst 13.1) resulted in some improvement, but still pretty bad performance overall: Minecraft stabilizes at 13-17 FPS, but at least the CPU load is "only" at 45-60%. Still 150% CPU use for 1080p video rendering on YouTube in Chromium. Massive improvement for 1080p H264 in VLC: 40-50% CPU use and no visible jitter glxgears performance about doubled to 25-30 FPS when maximized. fgl_glxgears still at ~10 FPS when maximized.

  Read the article

• Why would Copying a Large Image to the Clipboard Freeze a Computer?

  - by Akemi Iwaya

  Sometimes, something really odd happens when using our computers that makes no sense at all…such as copying a simple image to the clipboard and the computer freezing up because of it. An image is an image, right? Today’s SuperUser post has the answer to a puzzled reader’s dilemna. Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-driven grouping of Q&A web sites. Original image courtesy of Wikimedia. The Question SuperUser reader Joban Dhillon wants to know why copying an image to the clipboard on his computer freezes it up: I was messing around with some height map images and found this one: (http://upload.wikimedia.org/wikipedia/commons/1/15/Srtm_ramp2.world.21600×10800.jpg) The image is 21,600*10,800 pixels in size. When I right click and select “Copy Image” in my browser (I am using Google Chrome), it slows down my computer until it freezes. After that I must restart. I am curious about why this happens. I presume it is the size of the image, although it is only about 6 MB when saved to my computer. I am also using Windows 8.1 Why would a simple image freeze Joban’s computer up after copying it to the clipboard? The Answer SuperUser contributor Mokubai has the answer for us: “Copy Image” is copying the raw image data, rather than the image file itself, to your clipboard. The raw image data will be 21,600 x 10,800 x 3 (24 bit image) = 699,840,000 bytes of data. That is approximately 700 MB of data your browser is trying to copy to the clipboard. JPEG compresses the raw data using a lossy algorithm and can get pretty good compression. Hence the compressed file is only 6 MB. The reason it makes your computer slow is that it is probably filling your memory up with at least the 700 MB of image data that your browser is using to show you the image, another 700 MB (along with whatever overhead the clipboard incurs) to store it on the clipboard, and a not insignificant amount of processing power to convert the image into a format that can be stored on the clipboard. Chances are that if you have less than 4 GB of physical RAM, then those copies of the image data are forcing your computer to page memory out to the swap file in an attempt to fulfil both memory demands at the same time. This will cause programs and disk access to be sluggish as they use the disk and try to use the data that may have just been paged out. In short: Do not use the clipboard for huge images unless you have a lot of memory and a bit of time to spare. Like pretty graphs? This is what happens when I load that image in Google Chrome, then copy it to the clipboard on my machine with 12 GB of RAM: It starts off at the lower point using 2.8 GB of RAM, loading the image punches it up to 3.6 GB (approximately the 700 MB), then copying it to the clipboard spikes way up there at 6.3 GB of RAM before settling back down at the 4.5-ish you would expect to see for a program and two copies of a rather large image. That is a whopping 3.7 GB of image data being worked on at the peak, which is probably the initial image, a reserved quantity for the clipboard, and perhaps a couple of conversion buffers. That is enough to bring any machine with less than 8 GB of RAM to its knees. Strangely, doing the same thing in Firefox just copies the image file rather than the image data (without the scary memory surge). Have something to add to the explanation? Sound off in the comments. Want to read more answers from other tech-savvy Stack Exchange users? Check out the full discussion thread here.

  Read the article

• PC to USB transfer slow

  - by Vipin Ms

  I'm having trouble with USB transfer,not with external hard disk. Transfer starts with like, for the transfer of 700MB file it starts with 30mb/s and towards the end it stops at 0s and stays put for like 3-4 mins to transfer the last bit. I have tried different USB devices, but no luck. Is it a bug? Another important point is, in Kubuntu there is no such issue. So is it something related to Gnome? I'm using Ubuntu 11.10 64bit. Somebody please help, it's really annoying. Here are the details. PC all of my drives are in ext4. USB I tried ext3,ntfs and fat32. All having the same problem. Here are my USB controllers details: root@LAB:~# lspci|grep USB 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) Here is an example of one transfer. I connected one of my 4GB usb device. Nov 24 12:01:25 LAB kernel: [ 1175.082175] userif-2: sent link up event. Nov 24 12:01:25 LAB kernel: [ 1695.684158] usb 2-2: new high speed USB device number 3 using ehci_hcd Nov 24 12:01:25 LAB mtp-probe: checking bus 2, device 3: "/sys/devices/pci0000:00/0000:00:1d.7/usb2/2-2" Nov 24 12:01:26 LAB mtp-probe: bus: 2, device: 3 was not an MTP device Nov 24 12:01:26 LAB kernel: [ 1696.132680] usbcore: registered new interface driver uas Nov 24 12:01:26 LAB kernel: [ 1696.142528] Initializing USB Mass Storage driver... Nov 24 12:01:26 LAB kernel: [ 1696.142919] scsi4 : usb-storage 2-2:1.0 Nov 24 12:01:26 LAB kernel: [ 1696.143146] usbcore: registered new interface driver usb-storage Nov 24 12:01:26 LAB kernel: [ 1696.143150] USB Mass Storage support registered. Nov 24 12:01:27 LAB kernel: [ 1697.141657] scsi 4:0:0:0: Direct-Access SanDisk U3 Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS Nov 24 12:01:27 LAB kernel: [ 1697.168827] sd 4:0:0:0: Attached scsi generic sg2 type 0 Nov 24 12:01:27 LAB kernel: [ 1697.169262] sd 4:0:0:0: [sdb] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB) Nov 24 12:01:27 LAB kernel: [ 1697.169762] sd 4:0:0:0: [sdb] Write Protect is off Nov 24 12:01:27 LAB kernel: [ 1697.169767] sd 4:0:0:0: [sdb] Mode Sense: 45 00 00 08 Nov 24 12:01:27 LAB kernel: [ 1697.171386] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.171391] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.173503] sd 4:0:0:0: [sdb] No Caching mode page present Nov 24 12:01:27 LAB kernel: [ 1697.173510] sd 4:0:0:0: [sdb] Assuming drive cache: write through Nov 24 12:01:27 LAB kernel: [ 1697.175337] sdb: sdb1 After that I initiated one transfer. lsof -p 3575|tail -2 mv 3575 root 3r REG 8,8 1719599104 4325379 /media/Misc/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi mv 3575 root 4w REG 8,17 1046347776 15 /media/SREE/The Tree of Life (2011) DVDRip XviD-MAXSPEED/The Tree of Life (2011) DVDRip XviD-MAXSPEED www.torentz.3xforum.ro.avi Here are the total time spent on that transfer. root@LAB:/media/SREE# time mv /media/Misc/The\ Tree\ of\ Life\ \(2011\)\ DVDRip\ XviD-MAXSPEED/ /media/SREE/ real 11m49.334s user 0m0.008s sys 0m5.260s root@LAB:/media/SREE# df -T|tail -2 /dev/sdb1 vfat 3918344 1679308 2239036 43% /media/SREE /dev/sda8 ext4 110110576 60096904 50013672 55% /media/Misc Do you think this is normal?? Approximately 12 minutes for 1.6Gb transfer? Thanks.

  Read the article

• Dissing Architects, or "What's wrong with the coffee?"

  - by Bob Rhubart

  In my conversations with people in architect roles, tales of animosity, disrespect, and outright hostility aren't uncommon. And it's clear that in more than a few organizations architects regularly face a tough uphill climb. For architects with the requisite combination of technical, organizational, and people skills, that rough treatment is grossly undeserved. But tales of unqualified people in positions up and down the IT food chain are also easy to come by. So what's the other side of the architect story? Are some architects tarnishing the role and making life miserable for their more qualified colleagues? The various quotes included below were culled from a variety of sources. The criticism is harsh, and the people behind these quotes clearly have issues with architects. Still, whether based on mere opinion or actual experience, the comments shed some light on behaviors that should raise red flags for anyone pursuing a career as an architect. If you're an architect, and you've ever noticed that your coffee tastes like window cleaner, or your car is repeatedly keyed, or no one ever holds the elevator for you, maybe you need to do a little soul searching... Those Who Can, Code; Those Who Can't, Architect | Joe Winchester [May 18, 2007] "At the moment there seems to be an extremely unhealthy obsession in software with the concept of architecture. A colleague of mine, a recent graduate, told me he wished to become a software architect. He was drawn to the glamour of being able to come up with grandiose ideas - sweeping generalized designs, creating presentations to audiences of acronym addicts, writing esoteric academic papers, speaking at conferences attended by headless engineers on company expense accounts hungrily seeking out this year's grail, and creating e-mails with huge cc lists from people whose signature footer is more interesting than the content. I tried to re-orient him into actually doing some coding, to join a team that has a good product and keen users both of whom are pushing requirements forward, to no avail. Somehow the lure of being an architecture astronaut was too strong and I lost him to the dark side." Don't Let Architecture Astronauts Scare You | Joel Spolsky [April 21, 2001] "It's very hard to get them to write code or design programs, because they won't stop thinking about Architecture. They're astronauts because they are above the oxygen level, I don't know how they're breathing. They tend to work for really big companies that can afford to have lots of unproductive people with really advanced degrees that don't contribute to the bottom line. Remember that the architecture people are solving problems that they think they can solve, not problems which are useful to solve." Non Coding Architects Suck | Richard Henderson [May 24, 2010] "If a guy with a badge saying 'system architect' looks blank on low-level issues then he is not an architect, he is a business-analyst who went on a course. He will probably wax lyrical on all things high-level and 'important.' He will produce lovely object hierarchies without a clue to implementation. He will have a moustache and play golf." Architects Play Golf | Sunir Shah [August 15, 2012] "Often arrogant architects are difficult to get a hold of during the implementation phase because they no longer feel the need to stick around. Especially around midnight when most of the poor sob [sic] developers are still banging away. After all, they've already solved the problem--the rest is just an implementation exercise." Engineer vs Architect(Part of a discussion on the IT Architect Network Group on LinkedIn) "[An] architect spends his time producing white papers full of acronyms he does not understand but that impress his boss [while the] engineer keeps his head down and does the actual job." Architects Don't Code | [Author Unknown] "Faulty belief: System Architects don't need to code anymore. They know what they are talking about by virtue of the fact that they are System Architects."

  Read the article

• Ubuntu 13.04 installation issues: unable to handle kernel paging request error

  - by user173944

  I wish I could say that I’ve done more for the Linux community as of recent but I am very VERY new to all of this and I feel very much in over my head. I figured I would install Ubuntu. on my computer and then I would learn and contribute to the community simultaneously. I will try to be as detailed as I can, please ask questions if you need clarification. I installed Ubuntu. 13.04 (64-bit) on my dell Inspiron 1501. This has an AMD Turion 64-bit TL-56 1.8 Ghz mobile processor. It is a dual core. It has an ATI Radeon Xpress 1150 chipset in it as well. As of right now I only have a total of 2Ghz ram, however I was planning on upgrading that in the near future so I opted for the 64-bit Ubuntu. 13.04. I first tried the live CD and everything seemed to be functioning correctly other than the wireless (but that's not the issue at hand, there are plenty of guides on the internet on how to get that functioning). The internet worked just fine when it was plugged in so no issues there. However, once I went from that to installing 13.04 (just 13.04, no dual partitioning... I want this computer to run strictly Ubuntu.) it did not work. It took me into a shell that I could not type anything into. In this shell it said Bug: unable to handle kernel paging and then it called a bunch of traces and froze up. I had to hard reset the laptop. I tried the boot-repair program multiple times with many different settings and typically after starting up the laptop would say something along the lines of recursive errors. will attempt to fix and then it would attempt to fix a couple of things, and then the computer would freeze up after the text said end trace... so I had to hard reset it again. I'm not an impatient person either, when I say it would freeze up it would be for a period of at least 15 minutes each time before I decided to hard reset. I attempted to install 12.10 on it instead and I got the same exact message, and when I ran boot-repair it did the same exact thing as before. I am currently in the process of running memtest64+ on the computer's memory, though I really don't believe that, nor any of the hardware is at fault due to the fact that it was still running windows vista perfectly when I had decided to switch over to Ubuntu. so far the memtest has came back just fine without any errors, but I’ve only been running it for approximately an hour. So this is the situation I’m in. I did notice when I was using the live disk that the video driver needed updated so I performed that, though I’m fairly certain that has nothing to do with this. I have also attempted (though I’m not certain that my attempt was successful in accomplishing what I had planned) to manually edit the grub settings by making acpi=0 along top of adding nomodeset to the boot commands. Like I said, I’m not sure I did that correctly though, but I’m fairly certain I did. If anyone needs any more information I will be more than happy to provide it, I will post back once I get the full results of the memtest. I very much appreciate any ideas anyone else has, I’ve been at this for a few days to no avail... thank you

  Read the article

• Project Euler 17: (Iron)Python

  - by Ben Griswold

  In my attempt to learn (Iron)Python out in the open, here’s my solution for Project Euler Problem 17.  As always, any feedback is welcome. # Euler 17 # http://projecteuler.net/index.php?section=problems&id=17 # If the numbers 1 to 5 are written out in words: # one, two, three, four, five, then there are # 3 + 3 + 5 + 4 + 4 = 19 letters used in total. # If all the numbers from 1 to 1000 (one thousand) # inclusive were written out in words, how many letters # would be used? # # NOTE: Do not count spaces or hyphens. For example, 342 # (three hundred and forty-two) contains 23 letters and # 115 (one hundred and fifteen) contains 20 letters. The # use of "and" when writing out numbers is in compliance # with British usage. import time start = time.time() def to_word(n): h = { 1 : "one", 2 : "two", 3 : "three", 4 : "four", 5 : "five", 6 : "six", 7 : "seven", 8 : "eight", 9 : "nine", 10 : "ten", 11 : "eleven", 12 : "twelve", 13 : "thirteen", 14 : "fourteen", 15 : "fifteen", 16 : "sixteen", 17 : "seventeen", 18 : "eighteen", 19 : "nineteen", 20 : "twenty", 30 : "thirty", 40 : "forty", 50 : "fifty", 60 : "sixty", 70 : "seventy", 80 : "eighty", 90 : "ninety", 100 : "hundred", 1000 : "thousand" } word = "" # Reverse the numbers so position (ones, tens, # hundreds,...) can be easily determined a = [int(x) for x in str(n)[::-1]] # Thousands position if (len(a) == 4 and a[3] != 0): # This can only be one thousand based # on the problem/method constraints word = h[a[3]] + " thousand " # Hundreds position if (len(a) >= 3 and a[2] != 0): word += h[a[2]] + " hundred" # Add "and" string if the tens or ones # position is occupied with a non-zero value. # Note: routine is broken up this way for [my] clarity. if (len(a) >= 2 and a[1] != 0): # catch 10 - 99 word += " and" elif len(a) >= 1 and a[0] != 0: # catch 1 - 9 word += " and" # Tens and ones position tens_position_value = 99 if (len(a) >= 2 and a[1] != 0): # Calculate the tens position value per the # first and second element in array # e.g. (8 * 10) + 1 = 81 tens_position_value = int(a[1]) * 10 + a[0] if tens_position_value <= 20: # If the tens position value is 20 or less # there's an entry in the hash. Use it and there's # no need to consider the ones position word += " " + h[tens_position_value] else: # Determine the tens position word by # dividing by 10 first. E.g. 8 * 10 = h[80] # We will pick up the ones position word later in # the next part of the routine word += " " + h[(a[1] * 10)] if (len(a) >= 1 and a[0] != 0 and tens_position_value > 20): # Deal with ones position where tens position is # greater than 20 or we have a single digit number word += " " + h[a[0]] # Trim the empty spaces off both ends of the string return word.replace(" ","") def to_word_length(n): return len(to_word(n)) print sum([to_word_length(i) for i in xrange(1,1001)]) print "Elapsed Time:", (time.time() - start) * 1000, "millisecs" a=raw_input('Press return to continue')

  Read the article

• Oracle Database Upcoming Event dates to know

  - by mandy.ho

  February may be a short month, but it's not short of exciting Oracle events. From information packed "Real Performance Days" to participation in one of the biggest IT Security events - look out for Oracle Database and let us know if you are there with us! Feb 13-18, 2011 - Las Vegas, NV TDWI World Conference Series Join Oracle in highlighting Exadata x2-2 and x2-8, along with Oracle Business Intelligence, Enterprise Performance management and Data Warehousing solutions. Oracle will be presenting a workshop - Oracle Data Integration: Best-of-Breed Solutions for the Enterprise Wednesday, February 16, 2011 7p.m - 9p.m Glen Goodrich, Director of Product Management Christophe Dupupet, Director of Product Management, Data Integration http://events.tdwi.org/events/las-vegas-world-conference-2011/sessions/session-list.aspx Feb 14-17, 2011 - Barcelona, Spain Mobile World Congress MWC is an event where Oracle showcases the near complete breadth and depth of value that our Communications Industry strategy and Hardware and Software Solutions can deliver. Oracle supports Communications Service Providers today and delivers platforms and flexibility primed for the future. Oracle will have a two story Pavilion, along with an Oracle Java and Embedded Solutions Center - App Planet. The Exhibition times are Monday, 14th February 09.00 - 19.00 Tuesday, 15th February 09.00 - 19.00 Wednesday, 16th February 09.00 - 19.00 Thursday, 17th February 09.00 - 16.00 Have questions? Meet with Oracle Sales representatives at the Oracle Café. Open every day from 9am to 17:00pm. http://eventreg.oracle.com/webapps/events/ns/EventsDetail.jsp?p_eventId=109912&src=6973382&src=6973382&Act=4 Feb 14-18, 2011 - San Francisco, CA RSA Conference As the world's most complete, open, integrated business software and hardware systems provider, Oracle can uniquely safeguard your information throughout its entire lifecycle. Learn more by attending these sessions: Cloud Computing: A Brave New World for Security and Privacy (CLD-201) Wednesday, February 16 at 8:30 a.m. Databases Under Attack - Securing Heterogeneous Database Infrastructures (DAS-301) Thursday, February 17, 2011 at 8:30 a.m. Seven Steps to Protecting Databases (DAS-402) Friday, February 18 at 10:10 a.m. RSA Conference Attendees will also have the opportunity to meet with Oracle Security Solution experts, see live product demos and more by visiting booth # 1559. Hours: Monday, February 14, 6:00 p.m. - 8:00 p.m., Tuesday, February 15, 11:00 a.m. - 6:00 p.m. and 4:30 p.m. - 6:00p.m., Wednesday, February 16, 11:00 a.m. - 6:00 p.m., and Thursday, February 17, 11:00 a.m. - 3:00 p.m. http://eventreg.oracle.com/webapps/events/ns/EventsDetail.jsp?p_eventId=127657&src=6967733&src=6967733&Act=12 Feb 21-25, 2011 - Various Locations IOUG Presents - A Day of Real World Performance with Tom Kyte, Andrew Holdsworth and Graham Wood These Oracle experts will debate, discuss and delineate the best practices for designing hardware architectures, deploying Oracle databases, and developing applications that deliver the fastest possible performance for your business.Topics are covered in a conversational format - with all three chiming in where appropriate. Each presenter has their own screen projector to demonstrate their individual points to the participants. Customers will have the opportunity to get their specific performance/tuning questions answered and learn how to balance all the different environmental requirements for their applications to improve performance. Register today for the following dates and locations • February 21 in San Diego, CA • February 22 in Los Angeles, CA • February 23 in Seattle, WA • February 25 in Phoenix, AZ http://www.ioug.org/tabid/194/Default.aspx Feb 8-24 - Various Oracle Enterprise Cloud Summit This series of full-day events with cloud experts, sharing real-world best practices, reference architectures and more continues during the month of February. Attend the Oracle Enterprise Cloud Summit to learn how to: • Build a state-of-the-art cloud architecture • Leverage your existing IT investments • Optimize your IT management processes Whether you are considering a move to cloud computing or have already adopted a cloud model, this event offers you the insights you need to take full advantage of cloud computing. Check below to see if the event is coming to a city near you. http://www.oracle.com/us/corporate/events/cloud-events-214342.html

  Read the article

• wifi hardware switch doesn't work on a Dell 1018

  - by user42566

  I have a problem with my Dell 1018 Inspiron. I can't switch the wifi on, through the key on the keyboard. I think it's a driver problem since Ubuntu 11.10. This are the versions i tried: Ubuntu 10.04 / 10.10 It's possible to install the driver by hand: sudo add-apt-repository ppa:lexical/hwe-wireless sudo apt-get update sudo apt-get install rtl8192ce-dkms Ubuntu 11.04 It works out of the box Ubuntu 11.10 / 12.04 I haven’t found any solution for these versions. The "ppa:lexical/hwe-wireless" doesn't work for these versions. It says Can not find package rtl8192ce-dkms. The window of additional drivers is empty. So I can't install the driver. The wired network works good. Here is some information: 0: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes sudo lshw -class network *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 05 serial: 5c:26:0a:0d:20:10 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0f2c000-f0f2cfff memory:f0f18000-f0f1bfff *-network description: Wireless interface product: RTL8188CE 802.11b/g/n WiFi Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 01 serial: 70:f1:a1:fe:15:bd width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rtl8192ce driverversion=3.2.0-22-generic-pae firmware=N/A ip=192.168.1.76 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 ioport:3000(size=256) memory:f0100000-f0103fff mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation N10 Family DMI Bridge [8086:a010] 00:02.0 VGA compatible controller [0300]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a011] 00:02.1 Display controller [0380]: Intel Corporation N10 Family Integrated Graphics Controller [8086:a012] 00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02) 00:1c.0 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 1 [8086:27d0] (rev 02) 00:1c.1 PCI bridge [0604]: Intel Corporation N10/ICH 7 Family PCI Express Port 2 [8086:27d2] (rev 02) 00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) 00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) 00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) 00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) 00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) 00:1f.0 ISA bridge [0601]: Intel Corporation NM10 Family LPC Controller [8086:27bc] (rev 02) 00:1f.2 SATA controller [0106]: Intel Corporation N10/ICH7 Family SATA Controller [AHCI mode] [8086:27c1] (rev 02) 00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02) 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 07:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) mark@mark-Inspiron-1018:~$ mark@mark-Inspiron-1018:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 174f:1127 Syntek mark@mark-Inspiron-1018:~$

  Read the article

• Can't connect to VPN on Ubuntu 12.04

  - by 12rad

  I'm having a lot of trouble connecting to VPN. This used to work on my machine, but i recently did an update and it's stopped working. I'm not sure what the problem is. My question is how do i debug this? I'm not able to narrow it down to a specific problem. This is what i get when i tail the syslogs. Would appreciate any help! Nov 6 23:42:52 meera NetworkManager[1137]: <info> Starting VPN service 'pptp'... Nov 6 23:42:52 meera NetworkManager[1137]: <info> VPN service 'pptp' started (org.freedesktop.NetworkManager.pptp), PID 6132 Nov 6 23:42:52 meera NetworkManager[1137]: <info> VPN service 'pptp' appeared; activating connections Nov 6 23:42:52 meera NetworkManager[1137]: <info> VPN plugin state changed: starting (3) Nov 6 23:42:52 meera NetworkManager[1137]: <info> VPN connection 'NAME VPN' (Connect) reply received. Nov 6 23:42:52 meera pppd[6136]: Plugin /usr/lib/pppd/2.4.5/nm-pptp-pppd-plugin.so loaded. Nov 6 23:42:52 meera pppd[6136]: pppd 2.4.5 started by root, uid 0 Nov 6 23:42:52 meera chat[6139]: timeout set to 15 seconds Nov 6 23:42:52 meera chat[6139]: abort on (NO CARRIER) Nov 6 23:42:52 meera chat[6139]: abort on (NO DIALTONE) Nov 6 23:42:52 meera chat[6139]: abort on (ERROR) Nov 6 23:42:52 meera chat[6139]: abort on (NO ANSWER) Nov 6 23:42:52 meera chat[6139]: abort on (BUSY) Nov 6 23:42:52 meera chat[6139]: abort on (Username/Password Incorrect) Nov 6 23:42:52 meera chat[6139]: send (AT^M) Nov 6 23:42:52 meera pptp[6138]: nm-pptp-service-6132 log[main:pptp.c:314]: The synchronous pptp option is NOT activated Nov 6 23:42:52 meera chat[6139]: expect (OK) Nov 6 23:42:52 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 1 'Start-Control-Connection-Request' Nov 6 23:42:53 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_disp:pptp_ctrl.c:739]: Received Start Control Connection Reply Nov 6 23:42:53 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_disp:pptp_ctrl.c:773]: Client connection established. Nov 6 23:42:53 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 7 'Outgoing-Call-Request' Nov 6 23:42:54 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_disp:pptp_ctrl.c:858]: Received Outgoing Call Reply. Nov 6 23:42:54 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_disp:pptp_ctrl.c:897]: Outgoing call established (call ID 0, peer's call ID 13077). Nov 6 23:42:54 meera pptp[6138]: nm-pptp-service-6132 warn[decaps_hdlc:pptp_gre.c:231]: The ppp mode is synchronous, yet no pptp --sync option is specified! Nov 6 23:43:07 meera chat[6139]: alarm Nov 6 23:43:07 meera chat[6139]: Failed Nov 6 23:43:07 meera pppd[6136]: Script chat -v -f /etc/ppp/chat-ztisp finished (pid 6139), status = 0x3 Nov 6 23:43:07 meera pppd[6136]: Connect script failed Nov 6 23:43:07 meera pppd[6136]: Waiting for 1 child processes... Nov 6 23:43:07 meera pppd[6136]: script /usr/sbin/pptp 204.197.218.90 --nolaunchpppd --loglevel 0 --logstring nm-pptp-service-6132, pid 6138 Nov 6 23:43:07 meera pptp[6138]: nm-pptp-service-6132 warn[decaps_hdlc:pptp_gre.c:204]: short read (-1): Input/output error Nov 6 23:43:07 meera pptp[6138]: nm-pptp-service-6132 warn[decaps_hdlc:pptp_gre.c:216]: pppd may have shutdown, see pppd log Nov 6 23:43:07 meera pptp[6143]: nm-pptp-service-6132 log[callmgr_main:pptp_callmgr.c:234]: Closing connection (unhandled) Nov 6 23:43:07 meera pppd[6136]: Script /usr/sbin/pptp 204.197.218.90 --nolaunchpppd --loglevel 0 --logstring nm-pptp-service-6132 finished (pid 6138), status = 0x0 Nov 6 23:43:07 meera pptp[6143]: nm-pptp-service-6132 log[ctrlp_rep:pptp_ctrl.c:251]: Sent control packet type is 12 'Call-Clear-Request' Nov 6 23:43:07 meera pptp[6143]: nm-pptp-service-6132 log[call_callback:pptp_callmgr.c:79]: Closing connection (call state) Nov 6 23:43:07 meera pppd[6136]: Exit. Nov 6 23:43:07 meera NetworkManager[1137]: <warn> VPN plugin failed: 1 Nov 6 23:43:07 meera NetworkManager[1137]: <info> VPN plugin state changed: stopped (6) Nov 6 23:43:07 meera NetworkManager[1137]: <info> VPN plugin state change reason: 0 Nov 6 23:43:07 meera NetworkManager[1137]: <warn> error disconnecting VPN: Could not process the request because no VPN connection was active.

  Read the article

• Using Teleriks new LINQ implementation to connect to MySQL

  Last week Telerik released a new LINQ implementation that is simple to use and produces domain models very fast. Built on top of the enterprise grade OpenAccess ORM, you can connect to any database that OpenAccess can connect to such as: SQL Server, MySQL, Oracle, SQL Azure, VistaDB, etc. Today I will show you how to build a domain model using MySQL as your back end. To get started, you have to download MySQL 5.x and the MySQL Workbench and also, as my colleague Alexander Filipov at Telerik reminded me, make sure you install the MySQL .NET Connector, which is available here.  I like to use Northwind, ok it gives me the warm and fuzzies, so I ran a script to produce Northwind on my MySQL server. There are many ways you can get Northwind on your MySQL database, here is a helpful blog to get your started. I also manipulated the first record to indicate that I am in MySQL and gave a look via the MySQL Workbench. Ok, time to build our model! Start up the Domain Model wizard by right clicking on the project in Visual Studio (I have a Web project) and select Add|New Item and choose Telerik OpenAccess Domain Model from the new item list. When the wizard comes up, choose MySQL as your back end and enter in the name of your saved MySQL connection. If you dont have a saved MySQL connection set up in Visual Studio, click on New Connection and enter in the proper connection information. *Note, this is where you need to have the MySQL .NET connector installed. After you set your connection to the MySQL database server, you have to choose which tables to include in your model. Just for fun, I will choose all of them. Give your model a name, like NorthwindEntities and click finish. That is it. Now lets consume the model with ASP .net. I created a simple page that also has a GridView on it. On my page load I wrote this code, by now it should look very familiar, a simple LINQ query filtering customers by country (Germany) and binding the results to the grid.  1: protected void Page_Load(object sender, EventArgs e) 2: { 3: if (!IsPostBack) 4: { 5: //a reference to the data context 6: NorthwindEntities dat = new NorthwindEntities(); 7: //LINQ Statement 8: var result = from c in dat.Customers 9: where c.Country == "Germany" 10: select c; 11: //Databinding to the Gridview 12: GridView1.DataSource = result; 13: GridView1.DataBind(); 14: } 15: } .csharpcode, .csharpcode pre{ font-size: small; color: black; font-family: consolas, "Courier New", courier, monospace; background-color: #ffffff; /*white-space: pre;*/}.csharpcode pre { margin: 0em; }.csharpcode .rem { color: #008000; }.csharpcode .kwrd { color: #0000ff; }.csharpcode .str { color: #006080; }.csharpcode .op { color: #0000c0; }.csharpcode .preproc { color: #cc6633; }.csharpcode .asp { background-color: #ffff00; }.csharpcode .html { color: #800000; }.csharpcode .attr { color: #ff0000; }.csharpcode .alt { background-color: #f4f4f4; width: 100%; margin: 0em;}.csharpcode .lnum { color: #606060; } F5 produces the following. Tomorrow Ill show how to take the same model and create an Astoria/OData data feed. Technorati Tags: MySQL Did you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• October 2013 Fusion Middleware (FMW) Proactive Patches released

  - by Irina

  We are glad to announce that the following Fusion Middleware (FMW) Proactive  patches were released on October 15, 2013.Bundle PatchesBundle patches are collections of controlled, well tested critical bug fixes for a specific product  which may include security contents and occasionally minor enhancements. These are cumulative in nature meaning the latest bundle patch in a particular series includes the contents of the previous bundle patches released.  A suite bundle patch is an aggregation of multiple product  bundle patches that are part of a product suite. Oracle Identity Management Suite Bundle Patch 11.1.1.5.5 consisting of Oracle Identity Manager (OIM) 11.1.1.5.9 bundle patch Oracle Access Manager (OAM) 11.1.1.5.6 bundle patch. Oracle Adaptive Access Manager (OAAM) 11.1.1.5.2 bundle patch. Oracle Entitlement Server (OES) 11.1.1.5.4 bundle patch. Oracle Identity Management Suite Bundle Patch 11.1.2.0.4 consisting of Oracle Access Manager (OAM) 11.1.2.0.4 bundle patch. Oracle Adaptive Access Manager (OAAM) 11.1.2.0.2 bundle patch. Oracle Entitlement Server (OES) 11.1.2.0.2 bundle patch. Oracle Identity Analytics (OIA ) 11.1.1.5.6  bundle patch. Oracle GlassFish Server (OGFS) 2.1.1.22, 3.0.1.8 and 3.1.2.7 bundle patches. Oracle iPlanet Web Server (OiWS) 7.0.18 bundle patch Oracle SOA Suite (SOA) 11.1.1.7.1 bundle patch Oracle WebCenter Portal (WCP) 11.1.1.8.1 bundle patch Sun Role Manager (SRM) 4.1.7 and 5.0.3.2 bundle patches. Patch Set Updates (PSU)Patch Set Updates (PSU)  are collections of well controlled, well tested critical bug fixes for a specific product  that have been proven in customer environments. PSUs  may include security contents but no  enhancements are included. These are cumulative in nature meaning the latest PSU  in a particular series includes the contents of the previous PSUs  released. Oracle Exalogic 2.0.3.0.4 Physical Linux x86-64 and 2.0.4.0.4 Physical Solaris x86-64 PSUs. Oracle WebLogic Server 10.3.6.0.6 and 12.1.1.0.6 PSUs. Critical Patch Update (CPU)The Critical Patch Update program is Oracle's quarterly release of security fixes.The following additional patches were released as part of Oracle's Critical Patch Update program: Oracle JDeveloper 11.1.2.3.0, 11.1.2.4.0 and 12.1.2.0.0 Oracle Outside In Technology 8.4.0 and  8.4.1 Oracle Portal 11.1.1.6.0 Oracle Security Service  11.1.1.6.0, 11.1.1.7.0 and 12.1.2.0.0 Oracle WebCache 11.1.1.6.0 and 11.1.1.7.0 Oracle WebCenter Content 10.1.3.5.1, 11.1.1.6.0, 11.1.1.7.0 and 11.1.1.8.0 Oracle WebServices 10.1.3.5.0 and 11.1.1.6.0 For more information: Master Notes on Fusion Middleware Proactive Patching PSU and CPU October 2013  Availability Document Critical Patch Update Advisory -  October 2013

  Read the article

• Randomly placing items script not working - sometimes items spawn in walls, sometimes items spawn in weird locations

  - by Timothy Williams

  I'm trying to figure out a way to randomly spawn items throughout my level, however I need to make sure they won't spawn inside another object (walls, etc.) Here's the code I'm currently using, it's based on the Physics.CheckSphere(); function. This runs OnLevelWasLoaded(); It spawns the items perfectly fine, but sometimes items spawn partway in walls. And sometimes items will spawn outside of the SpawnBox range (no clue why it does that.) //This is what randomly generates all the items. void SpawnItems () { if (Application.loadedLevelName == "Menu" || Application.loadedLevelName == "End Demo") return; //The bottom corner of the box we want to spawn items in. Vector3 spawnBoxBot = Vector3.zero; //Top corner. Vector3 spawnBoxTop = Vector3.zero; //If we're in the dungeon, set the box to the dungeon box and tell the items we want to spawn. if (Application.loadedLevelName == "dungeonScene") { spawnBoxBot = new Vector3 (8.857f, 0, 9.06f); spawnBoxTop = new Vector3 (-27.98f, 2.4f, -15); itemSpawn = dungeonSpawn; } //Spawn all the items. for (i = 0; i != itemSpawn.Length; i ++) { spawnedItem = null; //Zeroes out our random location Vector3 randomLocation = Vector3.zero; //Gets the meshfilter of the item we'll be spawning MeshFilter mf = itemSpawn[i].GetComponent<MeshFilter>(); //Gets it's bounds (see how big it is) Bounds bounds = mf.sharedMesh.bounds; //Get it's radius float maxRadius = new Vector3 (bounds.extents.x + 10f, bounds.extents.y + 10f, bounds.extents.z + 10f).magnitude * 5f; //Set which layer is the no walls layer var NoWallsLayer = 1 << LayerMask.NameToLayer("NoWallsLayer"); //Use that layer as your layermask. LayerMask layerMask = ~(1 << NoWallsLayer); //If we're in the dungeon, certain items need to spawn on certain halves. if (Application.loadedLevelName == "dungeonScene") { if (itemSpawn[i].name == "key2" || itemSpawn[i].name == "teddyBearLW" || itemSpawn[i].name == "teddyBearLW_Admiration" || itemSpawn[i].name == "radio") randomLocation = new Vector3(Random.Range(spawnBoxBot.x, -26.96f), Random.Range(spawnBoxBot.y, spawnBoxTop.y), Random.Range(spawnBoxBot.z, -2.141f)); else randomLocation = new Vector3(Random.Range(spawnBoxBot.x, spawnBoxTop.x), Random.Range(spawnBoxBot.y, spawnBoxTop.y), Random.Range(-2.374f, spawnBoxTop.z)); } //Otherwise just spawn them in the box. else randomLocation = new Vector3(Random.Range(spawnBoxBot.x, spawnBoxTop.x), Random.Range(spawnBoxBot.y, spawnBoxTop.y), Random.Range(spawnBoxBot.z, spawnBoxTop.z)); //This is what actually spawns the item. It checks to see if the spot where we want to instantiate it is clear, and if so it instatiates it. Otherwise we have to repeat the whole process again. if (Physics.CheckSphere(randomLocation, maxRadius, layerMask)) spawnedItem = Instantiate(itemSpawn[i], randomLocation, Random.rotation); else i --; //If we spawned something, set it's name to what it's supposed to be. Removes the (clone) addon. if (spawnedItem != null) spawnedItem.name = itemSpawn[i].name; } } What I'm asking for is if you know what's going wrong with this code that it would spawn stuff in walls. Or, if you could provide me with links/code/ideas of a better way to check if an item will spawn in a wall (some other function than Physics.CheckSphere). I've been working on this for a long time, and nothing I try seems to work. Any help is appreciated.

  Read the article

• Lease Accounting Closed for Comment

  - by Theresa Hickman

  December 15, 2010 marked the last day to send public comments to FASB and IASB on lease accounting. June 2011 is the deadline for the final consideration of the Leases Exposure Draft that will be given to standard setters in order to create a new lease accounting standard. Landlords, lessees, retailers, airlines industry, etc. are all worried right now about the changes to lease accounting. They feel the changes will be too costly and complex without adding significant improvement to the quality and relevance of financial statements. In a nutshell, IASB and FASB want to abolish operating leases where the lessee records the periodic payments as an expense over time. The proposed changes will mean that the accounting for leases will move from the P&L and hit both the lessee's and lessor's balance sheets. For companies that occupy a lot of property, this could significantly increase their liabilities not to mention front-load much of the costs that they were able to spread out over time before. Why are IASB and FASB doing this? Their goal is to have consistent accounting for both the lessees and lessors with higher quality financial statements. Leasing is one of four major projects being undertaken by the IASB and FASB in order to complete convergence between US GAAP and IFRS. I spoke to our resident accounting expert Seamus Moran about this to better understand how this might impact accounting software. He reminded me that the proposed changes to both US GAAP and IFRS in respect to leases are "proposed." It is still inappropriate to account for leases the way they are being proposed and we still need to account for them in accordance to the current regulations, which is what current accounting software programs, such as E-Business Suite Release 12.1 and prior and PeopleSoft Enterprise support. The FASB (US GAAP) and IASB (IFRS) exposure drafts (EDs) that outline the proposal were published. The FASB edition was published on August 17th, with comments due by December 15th. The IASB edition was published on the same date, and comments were due in London on the same date. Exposure drafts are the method both the FASB and the IASB use to solicit General Acceptance, the "GA" in GAAP. Both Boards will consider the input they have received, and perhaps revise the proposal. The proposal has come in for some criticism, both from the finance houses and the uses of the leased assets. There is, given the opposition to it, an excellent chance that the Leasing proposal will be modified or rewritten. We will know this in about six months, the usual time it takes for the FASB and IASB to digest the comments they receive. If they feel the proposal has General Acceptance, they will issue the final Standard at that time; if not, they will issue a revised proposal with another year of comment of drafting. Oracle participates in the standard setting process and is fully aware of the leasing proposal. We have designs that would reflect the proposal in hand. These designs will be finalized when the proposal is finalized. It is likely that customers will develop new financial arrangements if the proposal is finalized, and we are working with customers and partners to stay in touch with people's business responses to the proposal. The IASB and FASB are aware that ERP companies will have to revise their software, and that the companies filing results under IFRS or under US GAAP will have to implement such software. The form and timing of the release of the updated software will depend on the schedule of the take up of the new standard, the complexity of the standard, and the releases supported at the time the standard becomes effective.

  Read the article

• Azure Mobile Services: lessons learned

  - by svdoever

  When I first started using Azure Mobile Services I thought of it as a nice way to: authenticate my users - login using Twitter, Google, Facebook, Windows Live create tables, and use the client code to create the columns in the table because that is not possible in the Azure Mobile Services UI run some Javascript code on the table crud actions (Insert, Update, Delete, Read) schedule a Javascript to run any 15 or more minutes I had no idea of the magic that was happening inside… where is the data stored? Is it a kind of big table, are relationships between tables possible? those Javascripts on the table crud actions, is that interpreted, what is that exactly? After working for some time with Azure Mobile Services I became a lot wiser: Those tables are just normal tables in an Azure SQL Server 2012 Creating the table columns through client code sucks, at least from my Javascript code, because the columns are deducted from the sent JSON data, and a datetime field is sent as string in JSON, so a string type column is created instead of a datetime column You can connect with SQL Management Studio to the Azure SQL Server, and although you can’t manage your columns through the SQL Management Studio UI, it is possible to just run SQL scripts to drop and create tables and indices When you create a table through SQL script, add the table with the same name in the Azure Mobile Services UI to hook it up and be able to access the table through the provided abstraction layer You can also go to the SQL Database through the Azure Mobile Services UI, and from there get in a web based SQL management studio where you can create columns and manage your data The table crud scripts and the scheduler scripts are full blown node.js scripts, introducing a lot of power with great performance The web based script editor is really powerful, I do most of my editing currently in the editor which has syntax highlighting and code completing. While editing the code JsHint is used for script validation. The documentation on Azure Mobile Services is… suboptimal. It is such a pity that there is no way to comment on it so the community could fill in the missing holes, like which node modules are already loaded, and which modules are available on Azure Mobile Services. Soon I was hacking away on Azure Mobile Services, creating my own database tables through script, and abusing the read script of an empty table named query to implement my own set of “services”. The latest updates to Azure Mobile Services described in the following posts added some great new features like creating web API’s, use shared code from your scripts, command line tools for managing Azure Mobile Services (upload and download scripts for example), support for node modules and git support: http://weblogs.asp.net/scottgu/archive/2013/06/14/windows-azure-major-updates-for-mobile-backend-development.aspx http://blogs.msdn.com/b/carlosfigueira/archive/2013/06/14/custom-apis-in-azure-mobile-services.aspx http://blogs.msdn.com/b/carlosfigueira/archive/2013/06/19/custom-api-in-azure-mobile-services-client-sdks.aspx In the mean time I rewrote all my “service-like” table scripts to API scripts, which works like a breeze. Bad thing with the current state of Azure Mobile Services is that the git support is not working if you are a co-administrator of your Azure subscription, and not and administrator (as in my case). Another bad thing is that Cross Origin Request Sharing (CORS) is not supported for the API yet, so no go yet from the browser client for API’s, which is my case. See http://social.msdn.microsoft.com/Forums/windowsazure/en-US/2b79c5ea-d187-4c2b-823a-3f3e0559829d/known-limitations-for-source-control-and-custom-api-features for more on these and other limitations. In his talk at Build 2013 Josh Twist showed that there is a work-around for accessing shared script code from the table scripts as well (another limitation mentioned in the post above). I could not find that code in the Votabl2 code example from the presentation at https://github.com/joshtwist/votabl2, but we can grab it from the presentation when it comes online on Channel9. By the way: you can always express your needs and ideas at http://mobileservices.uservoice.com, that’s the place they are listening to (I hope!).

  Read the article

• Free and Open Source Software in Oracle Solaris 11.1

  - by user13277799

  Oracle Solaris 11.1 contains number of Free and Open Source packages. The following table contains important FOSS packages with their versions available in this latest Oracle Solaris release. a2ps 4.14 aalib 1.4.0 pmtools 20071116 apache-ant 1.7.1 httpd 2.2.22 mod_dtrace 0.3.1 mod_fcgid 2.3.6 tomcat-connectors 1.2.28 mod_perl 2.0.4 mod_proxy_html 3.1.1 modsecurity-apache 2.5.9 mod_wsgi 3.3 apr 1.3.9 apr-util 1.3.9 areca 7.1 autoconf 2.68 autogen 5.9 automake 1.10 automake 1.11.2 automake 1.9.6 bash 4.1 bcc 0.16.17 beanshell 2.0b4 db 5.1.25 bind 9.6-ESV-R7-P2 binutils 2.21.1 bison 2.3 bzip2 1.0.6 cdrtools 3.00 clisp 2.47 cmake 2.8.6 gnu 0.5.11 conflict 20100627 convmv 1.15 coreutils 8.5 cups 1.4.5 curl 7.21.2 cvs 1.12.13 diffutils 2.8.7 doxygen 1.7.6.1 ejabberd 2.1.8 elinks 0.11.7 emacs 23.4 otp_src R12B-5 fcgi 2.4.0 fetchmail 6.3.22 flex 2.5.35 foomatic-db 20080903 foomatic-db-engine 3.0-20080903 foomatic-filters 4.0.15 foomatic-filters-ppds 20080818 fping 2.4b2_to gawk 3.1.8 gcc 3.4.3 gcc 4.5.2 gd 2.0.35 gdb 6.8 gdbm 1.8.3 gettext 0.16.1 grep 2.10 ghostscript 9.00 git 1.7.9.2 gnu-gs-fonts-other 6.0 gnu-gs-fonts-std 6.0 gmp 4.3.2 gnupg 2.0.17 gnuplot 4.6.0 pth 2.0.7 gocr 0.48 gperf 3.0.3 gpgme 1.1.8 grails 1.0.3 graphviz 2.28.0 tar 1.26 guile 1.8.6 gutenprint 5.2.7 gzip 1.4 hal-cups-utils 0.6.19 hexedit 1.2.12 hplip 3.10.9 httping 1.4.4 hwdata 0.5.11 iftop 0.17 ilmbase 1.0.1 ImageMagick 6.3.4 iperf 2.0.4 ipmitool 1.8.11 ircii 20060725 dhcp 4.1-ESV-R7 junit 4.10 INIT 2011-02-08 lcms 1.19 less 436 lftp 4.3.1 libassuan 2.0.1 confuse 2.6 libedit 20110802-3.0 libee 0.3.2 libestr 0.1.2 libevent 1.4.14b expat 2.1.0 libidn 1.19 libksba 1.1.0 libmcrypt 2.5.8 libmemcached 0.16 libmng 1.0.10 neon 0.29.5 libnet 1.1.5 libpcap 1.1.1 librsync 0.9.7 libsigsegv 2.6 libsndfile 1.0.23 libtecla 1.6.1 libtool 2.4.2 libtorrent 0.12.2 libusbugen 0.1.8 libusb 0.1.8 libxml2 2.7.6 libxslt 1.1.26 lighttpd 1.4.23 links 1.03 logilab-astng 0.19.0 logilab-common 0.40.0 lua 5.1.4 m4 1.4.12 make 3.82 mc 4.7.5.2 meld 1.4.0 memcached 1.4.5 memcached-java 2.0.1 mercurial 2.2.1 mpc 0.9 mpfr 2.4.2 mutt 1.5.21 mysql 5.1.37 ncftp 3.2.3 net-snmp 5.4.1 nethack 3.4.3 nmap 5.51 ntp-dev 4.2.5 open-fabrics 1.5.3 openexr 1.6.1 openldap 2.4.30 openscap 0.8.1 openssl 0.9.8q openssl 1.0.0j libopenusb 1.0.1 p7zip 9.20.1 pam_pkcs11 0.6.0 patch 2.5.9 pconsole 1.0 pcre 8.21 perl 5.12.4 DBI 1.58 Net-SSLeay 1.36 pmtools 1.10 XML-Parser 2.36 XML-Simple 2.18 PHP 5.2.17 PHP 5.3.14 pinentry 0.7.6 privoxy 3.0.17 proftpd 1.3.3 psutils p17 pv 1.2.0 pwgen 2.06 pylint 0.18.0 CherryPy 3.1.2 coverage 3.5 jsonrpclib 0.1.3 ldtp 2.1.1 M2Crypto 0.21.1 Mako 0.4.1 nose 1.1.2 ply 3.1 pybonjour 1.1.1 pycups 1.9.46 pycurl 7.19.0 lxml 2.3.3 pyOpenSSL 0.11 Python 2.6.8 Python 2.7.3 setuptools 0.6 quagga 0.99.19 quilt 0.60 rdiff-backup 1.3.3 readline 5.2 rpm2cpio 0.5.11 rsync 3.0.8 rsyslog 6.2.0 rtorrent 0.8.2 ruby 1.8.7 samba 3.6.6 sane-backends 1.0.19 sane-frontends 1.0.14 screen 4.0.3 sed 4.2.1 sendmail 8.14.5 slang 2.2.4 slib 3b1 slrn 0.9.9 snort 2.8.4.1 sox 14.3.2 spawn-fcgi 1.6.3 squid 3.1.18 stdcxx 4.2.1 subversion 1.7.5 sudo 1.8.4.5 swig 1.3.35 expect 5.45 tcl 8.5.9 tk 8.5.9 tls 1.6 tcpdump 4.1.1 tcsh 6.17.00 texinfo 4.7 tidy 1.0.0 timezone apache-tomcat 6.0.35 top 3.8beta1 trousers 0.3.6 unixODBC 2.3.0 unrar 4.1.4 unzip 6.0 vim 7.3 visual-panels wget 1.12 which 2.16 wireshark 1.8.2 wxGTK 2.8.12 xorriso 0.6.0 xz 5.0.1 zip 3.0 zlib 1.2.3 zsh 4.3.17

  Read the article

• Item cannot be installed or removed until the package catalogue is repaired

  - by Alex Thorne

  After installing Microsoft Windows Compatibility Layer (meta-package) i receive an error Item cannot be installed or removed until the package catalogue is repaired. Do you want to repair it Ok, I thought... I'll just click repair and be done with it. After doing so I receive another error. The full text reads: installArchives() failed: (Reading database ... (Reading database ... 5% (Reading database ... 10% (Reading database ... 15% (Reading database ... 20% (Reading database ... 25% (Reading database ... 30% (Reading database ... 35% (Reading database ... 40% (Reading database ... 45% (Reading database ... 50% (Reading database ... 55% (Reading database ... 60% (Reading database ... 65% (Reading database ... 70% (Reading database ... 75% (Reading database ... 80% (Reading database ... 85% (Reading database ... 90% (Reading database ... 95% (Reading database ... 100% (Reading database ... 212945 files and directories currently installed.) Unpacking libasound2:i386 (from .../libasound2_1.0.25-1ubuntu10_i386.deb) ... dpkg: error processing /var/cache/apt/archives/libasound2_1.0.25-1ubuntu10_i386.deb (--unpack): './usr/share/alsa/cards/ICE1712.conf' is different from the same file on the system dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/libasound2_1.0.25-1ubuntu10_i386.deb Error in function: SystemError: E:Sub-process /usr/bin/dpkg returned an error code (1) dpkg: dependency problems prevent configuration of wine1.4-i386:i386: wine1.4-i386:i386 depends on libasound2 (>= 1.0.23); however: Package libasound2:i386 is not installed. dpkg: error processing wine1.4-i386:i386 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of wine1.4: wine1.4 depends on wine1.4-i386 (= 1.4-0ubuntu4); however: Package wine1.4-i386 is not installed. Package wine1.4-i386:i386 is not configured yet. dpkg: error processing wine1.4 (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of wine: wine depends on wine1.4; however: Package wine1.4 is not configured yet. dpkg: error processing wine (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of wine1.4-common: wine1.4-common depends on wine1.4 (= 1.4-0ubuntu4); however: Package wine1.4 is not configured yet. dpkg: error processing wine1.4-common (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of wine1.4-amd64: wine1.4-amd64 depends on wine1.4-common (= 1.4-0ubuntu4); however: Package wine1.4-common is not configured yet. dpkg: error processing wine1.4-amd64 (--configure): dependency problems - leaving unconfigured So I click OK and now I'm back to previous screen ("Item cannot be installed ...") I click on cancel and go to the red circle on the top right on my screen and try to update from there and receive this error After that I just get thrown these errors So now I can't add or remove any programs on my system. Does anyone have any idea how to fix this?

  Read the article

• Working for free?

  - by Jonny

  I came across this article Work for Free that got me thinking. The goal of every employer is to gain more value from workers than the firm pays out in wages; otherwise, there is no growth, no advance, and no advantage for the employer. Conversely, the goal of every employee should be to contribute more to the firm than he or she receives in wages, and thereby provide a solid rationale for receiving raises and advancement in the firm. I don't need to tell you that the refusenik didn't last long in this job. In contrast, here is a story from last week. My phone rang. It was the employment division of a major university. The man on the phone was inquiring about the performance of a person who did some site work on Mises.org last year. I was able to tell him about a remarkable young man who swung into action during a crisis, and how he worked three 19-hour days, three days in a row, how he learned new software with diligence, how he kept his cool, how he navigated his way with grace and expertise amidst some 80 different third-party plug-ins and databases, how he saw his way around the inevitable problems, how he assumed responsibility for the results, and much more. What I didn't tell the interviewer was that this person did all this without asking for any payment. Did that fact influence my report on his performance? I'm not entirely sure, but the interviewer probably sensed in my voice my sense of awe toward what this person had done for the Mises Institute. The interviewer told me that he had written down 15 different questions to ask me but that I had answered them all already in the course of my monologue, and that he was thrilled to hear all these specifics. The person was offered the job. He had done a very wise thing; he had earned a devotee for life. The harder the economic times, the more employers need to know what they are getting when they hire someone. The job applications pour in by the buckets, all padded with degrees and made to look as impressive as possible. It's all just paper. What matters today is what a person can do for a firm. The resume becomes pro forma but not decisive under these conditions. But for a former boss or manager to rave about you to a potential employer? That's worth everything. What do you think? Has anyone here worked for free? If so, has it benefited you in any way? Why should(nt) you work for free (presuming you have the money from other means to keep you going)? Can you share your experience? Me, I am taking a year out of college and haven't gotten a degree yet so that's probably why most of my job applications are getting ignored. So im thinking about working for free for the experience?

  Read the article

• SQL 2012 Licensing Thoughts

  - by Geoff N. Hiten

  The only thing more controversial than new Federal Tax plans is new Licensing plans from Microsoft.  In both cases, everyone calculates several numbers.  First, will I pay more or less under this plan?  Second, will my competition pay more or less than now?  Third, will <insert interesting person/company here> pay more or less?  Not that items 2 and 3 are meaningful, that is just how people think. Much like tax plans, the devil is in the details, so lets see how this looks.  Microsoft shows it here: http://www.microsoft.com/sqlserver/en/us/future-editions/sql2012-licensing.aspx First up is a switch from per-socket to per-core licensing.  Anyone who didn’t see something like this coming should rapidly search for a new line of work because you are not paying attention.  The explosion of multi-core processors has made SQL Server a bargain.  Microsoft is in business to make money and the old per-socket model was not going to do that going forward. Per-core licensing also simplifies virtualization licensing.  Physical Core = Virtual Core, at least for licensing.  Oversubscribe your processors, that’s your lookout.  You still pay for  what is exposed to the VM.  The cool part is you can seamlessly move physical and virtual workloads around and the licenses follow.  The catch is you have to have Software Assurance to make the licenses mobile.  Nice touch there. Let’s have a moment of silence for the late, unlamented, largely ignored Workgroup Edition.  To quote the Microsoft  FAQ:  “Standard becomes our sole edition for basic database needs”.  Considering I haven’t encountered a singe instance of SQL Server Workgroup Edition in the wild, I don’t think this will be all that controversial. As for pricing, it looks like a wash with current per-socket pricing based on four core sockets.  Interestingly, that is the minimum core count Microsoft proposes to swap to transition per-socket to per-core if you are on Software Assurance.  Reading the fine print shows that if you are using more, you will get more core licenses: From the licensing FAQ. 15. How do I migrate from processor licenses to core licenses?  What is the migration path? Licenses purchased with Software Assurance (SA) will upgrade to SQL Server 2012 at no additional cost. EA/EAP customers can continue buying processor licenses until your next renewal after June 30, 2012. At that time, processor licenses will be exchanged for core-based licenses sufficient to cover the cores in use by processor-licensed databases (minimum of 4 cores per processor for Standard and Enterprise, and minimum of 8 EE cores per processor for Datacenter). Looks like the folks who invested in the AMD 12-core chips will make out like bandits. Now, on to something new: SQL Server Business Intelligence Edition. Yep, finally a BI-specific SKU licensed for server+CAL configurations only.  Note that Enterprise Edition still supports the complete feature set; the BI Edition is intended for smaller shops who want to use the full BI feature set but without needing Enterprise Edition scale (or costs).  No, you don’t get ColumnStore, Compression, or Partitioning in the BI Edition.  Those are Enterprise scale features, ThankYouVeryMuch.  Then again, your starting licensing costs are about one sixth of an Enterprise Edition system (based on an 8 core server). The only part of the message I am missing is if the current Failover Licensing Policy will change.  Do we need to fully or partially license failover servers?  That is a detail I definitely want to know.

  Read the article

• perl comparing 2 data file as array 2D for finding match one to one [migrated]

  - by roman serpa

  I'm doing a program that uses combinations of variables ( combiData.txt 63 rows x different number of columns) for analysing a data table ( j1j2_1.csv, 1000filas x 19 columns ) , to choose how many times each combination is repeated in data table and which rows come from (for instance, tableData[row][4]). I have tried to compile it , however I get the following message : Use of uninitialized value $val in numeric eq (==) at rowInData.pl line 34. Use of reference "ARRAY(0x1a2eae4)" as array index at rowInData.pl line 56. Use of reference "ARRAY(0x1a1334c)" as array index at rowInData.pl line 56. Use of uninitialized value in subtraction (-) at rowInData.pl line 56. Modification of non-creatable array value attempted, subscript -1 at rowInData.pl line 56. nothing This is my code: #!/usr/bin/perl use strict; use warnings; my $line_match; my $countTrue; open (FILE1, "<combiData.txt") or die "can't open file text1.txt\n"; my @tableCombi; while(<FILE1>) { my @row = split(' ', $_); push(@tableCombi, \@row); } close FILE1 || die $!; open (FILE2, "<j1j2_1.csv") or die "can't open file text1.txt\n"; my @tableData; while(<FILE2>) { my @row2 = split(/\s*,\s*/, $_); push(@tableData, \@row2); } close FILE2 || die $!; #function transform combiData.txt variable (position ) to the real value that i have to find in the data table. sub trueVal($){ my ($val) = $_[0]; if($val == 7){ return ('nonsynonymous_SNV'); } elsif( $val == 14) { return '1'; } elsif( $val == 15) { return '1';} elsif( $val == 16) { return '1'; } elsif( $val == 17) { return '1'; } elsif( $val == 18) { return '1';} elsif( $val == 19) { return '1';} else { print 'nothing'; } } #function IntToStr ( ) , i'm not sure if it is necessary) that transforms $ to strings , to use the function <eq> in the third loop for the array of combinations compared with the data array . sub IntToStr { return "$_[0]"; } for my $combi (@tableCombi) { $line_match = 0; for my $sheetData (@tableData) { $countTrue=0; for my $cell ( @$combi) { #my $temp =\$tableCombi[$combi][$cell] ; #if ( trueVal($tableCombi[$combi][$cell] ) eq $tableData[$sheetData][ $tableCombi[$combi][$cell] - 1 ] ){ #if ( IntToStr(trueVal($$temp )) eq IntToStr( $tableData[$sheetData][ $$temp-1] ) ){ if ( IntToStr(trueVal($tableCombi[$combi][$cell]) ) eq IntToStr($tableData[$sheetData][ $tableCombi[$combi][$cell] -1]) ){ $countTrue++;} if ($countTrue==@$combi){ $line_match++; #if ($line_match < 50){ print $tableData[$sheetData][4]." "; #} } } } print $line_match." \n"; }

  Read the article

• Persevering & Friday Night Big Ideas

  - by Oracle Accelerate for Midsize Companies

  by Jim Lein, Oracle Midsize Programs Every successful company, personal accomplishment, and philanthropic endeavor starts with one good idea. I have my best ideas on Friday evenings. The creative side of my brain is stimulated by end of week endorphins. Free thinking. Anything is possible. But, as my kids love to remind me, most of Dad's Friday Night Big Ideas (FNBIs) fizzle on the drawing board. Usually there's one barrier blocking the way that seems insurmountable by noon on Monday. For example, trekking the 486 mile Colorado Trail is on my bucket list. Since I have a job, I'll have to do it in bits and pieces--day hikes, weekends, and a vacation week here and there. With my trick neck, backpacking is not an option. How to survive equip myself for overnight backcountry travel was that one seemingly insurmountable barrier.  Persevering Lewis and Clark wouldn't have given up so I explored options and, as I blogged about back in December, I had an FNBI to hire llamas to carry my load. Last weekend, that idea came to fruition. Early Saturday morning, I met up with Bill, the owner of Antero Llamas, for an overnight training expedition along segment 14 of the Colorado Trail with a string of twelve llamas. It was a crash course on learning how to saddle, load, pasture, and mediate squabbles. Amazingly, we left the trailhead with me, the complete novice, at the lead. Instead of trying to impart three decades of knowledge on me in two days, Bill taught me two things: "Go With the Flow" and "Plan B". It worked. There were times I would be lost in thought for long stretches of time until one snort would remind me that I had a string of twelve llamas trailing behind. A funny thing happened along the trail... Up until last Saturday, my plan had been to trek all 28 segments of the trail east to west and sequentially. Out of some self-imposed sense of decorum. That plan presented myriad logistical challenges such as impassable snow pack on the Continental Divide when segment 6 is up next. On Sunday, as we trekked along the base of 14,000 ft peaks, I applied Bill's llama handling philosophy to my quest and came up with a much more realistic and enjoyable strategy for achieving my goal.  Seize opportunities to hike regardless of order. Define my own segments. Go west to east for awhile if it makes more sense. Let the llamas carry more creature comforts. Chill out.  I will still set foot on all 486 miles of the trail. Technically, the end result will be the same.And I and my traveling companions--human and camelid--will enjoy the journey more. Much more. Got Big Ideas of Your Own? Check out Tongal. This growing Oracle customer works with brands to crowd source fantastic ideas for promoting products and services. Your great idea could earn you cash.  Looking for more news and information about Oracle Solutions for Midsize Companies? Read the latest Oracle for Midsize Companies Newsletter Sign-up to receive the latest communications from Oracle’s industry leaders and experts Jim Lein I evangelize Oracle's enterprise solutions for growing midsize companies. I recently celebrated 15 years with Oracle, having joined JD Edwards in 1999. I'm based in Evergreen, Colorado and love relating stories about creativity and innovation whether they be about software, live music, or the mountains. The views expressed here are my own, and not necessarily those of Oracle.

  Read the article

• Physics like asteroides

  - by user2933016

  I try to make a ship that has the physic properties like asteroides. I have this for now(All in Java): Ship.class public class Ship { public static final float sMaxHealth = 0.1F; public static final float sMaxMoveVelocity = 5.0F; public static final float sMaxAngleVelocity = 20.0F; public static final float sRadius = 1.0F; public static final float sMoveDeceleration = 10.0F; public static final float sMoveAcceleration = 2.0F; public static final float sAngleDeceleration = 15.0F; public static final float sAngleAcceleration = 20.0F; private float mHealth; private float mXVelocity; private float mYVelocity; private float mAngleVelocity; private float mX; private float mY; private float mAngle; } (I let the getter and setter away for now) Controller code // Player input if(Gdx.input.isKeyPressed(Keys.UP)) { mPlayer.setXVelocity(mPlayer.getXVelocity() + (float) Math.cos(mPlayer.getAngle()) * Ship.sMoveAcceleration); mPlayer.setYVelocity(mPlayer.getYVelocity() + (float) Math.sin(mPlayer.getAngle()) * Ship.sMoveAcceleration); } if(Gdx.input.isKeyPressed(Keys.LEFT)) { mPlayer.setAngleVelocity(mPlayer.getAngleVelocity() + Ship.sAngleAcceleration * pDeltaTime); } if(Gdx.input.isKeyPressed(Keys.RIGHT)) { mPlayer.setAngleVelocity(mPlayer.getAngleVelocity() - Ship.sAngleAcceleration * pDeltaTime); } // X velocity if(mPlayer.getXVelocity() < 0) { if(-mPlayer.getXVelocity() > Ship.sMaxMoveVelocity) { mPlayer.setXVelocity(-Ship.sMaxMoveVelocity); } mPlayer.setXVelocity(mPlayer.getXVelocity() + Ship.sMoveDeceleration * pDeltaTime); if(mPlayer.getXVelocity() > 0) { mPlayer.setXVelocity(0); } } else if(mPlayer.getXVelocity() > 0) { if(mPlayer.getXVelocity() > Ship.sMaxMoveVelocity) { mPlayer.setXVelocity(Ship.sMaxMoveVelocity); } mPlayer.setXVelocity(mPlayer.getXVelocity() - Ship.sMoveDeceleration * pDeltaTime); if(mPlayer.getXVelocity() < 0) { mPlayer.setXVelocity(0); } } // Y velocity if(mPlayer.getYVelocity() < 0) { if(-mPlayer.getYVelocity() > Ship.sMaxMoveVelocity) { mPlayer.setYVelocity(-Ship.sMaxMoveVelocity); } mPlayer.setYVelocity(mPlayer.getYVelocity() + Ship.sMoveDeceleration * pDeltaTime); if(mPlayer.getYVelocity() > 0) { mPlayer.setYVelocity(0); } } else if(mPlayer.getYVelocity() > 0) { if(mPlayer.getYVelocity() > Ship.sMaxMoveVelocity) { mPlayer.setYVelocity(Ship.sMaxMoveVelocity); } mPlayer.setYVelocity(mPlayer.getYVelocity() - Ship.sMoveDeceleration * pDeltaTime); if(mPlayer.getYVelocity() < 0) { mPlayer.setYVelocity(0); } } // Angle velocity if(mPlayer.getAngleVelocity() < 0) { if(-mPlayer.getAngleVelocity() > Ship.sMaxAngleVelocity) { mPlayer.setAngleVelocity(-Ship.sMaxAngleVelocity); } mPlayer.setAngleVelocity(mPlayer.getAngleVelocity() + Ship.sAngleDeceleration * pDeltaTime); if(mPlayer.getAngleVelocity() > 0) { mPlayer.setAngleVelocity(0); } } else if(mPlayer.getAngleVelocity() > 0) { if(mPlayer.getAngleVelocity() > Ship.sMaxAngleVelocity) { mPlayer.setAngleVelocity(Ship.sMaxAngleVelocity); } mPlayer.setAngleVelocity(mPlayer.getAngleVelocity() - Ship.sAngleDeceleration * pDeltaTime); if(mPlayer.getAngleVelocity() < 0) { mPlayer.setAngleVelocity(0); } } mPlayer.setX(mPlayer.getX() + mPlayer.getXVelocity() * pDeltaTime); mPlayer.setY(mPlayer.getY() + mPlayer.getYVelocity() * pDeltaTime); mPlayer.setAngle(mPlayer.getAngle() + mPlayer.getAngleVelocity() * pDeltaTime); Why the ship does not behave like in asteroides ? What do I wrong?

  Read the article

< Previous Page | 238 239 240 241 242 243 244 245 246 247 248 249  | Next Page >