Search Results

Search found 741 results on 30 pages for 'pin'.

Page 25/30 | < Previous Page | 21 22 23 24 25 26 27 28 29 30  | Next Page >

• Is my motherboard failing, or is there some other issue?

  - by ThatGuy

  So, several months ago I put together my own desktop PC. I set up a dual boot to Windows and Ubuntu. Recently, without changing any settings or installing anything new, the wifi stopped working on windows (I use a wifi adapter). It said it was connected, Network settings showed that it was working and running trouble shooting had no results. My internet still works on any other device. I found that removing the adapter from the motherboard and plugging it back in was the only thing that fixed the problem. Reinstalling the wifi drivers did not help. I purchased a new Wifi adapter, but the problem persists. More recently, I had a much more discouraging development. Sometimes, turning on the computer results in a boot loop: BIOS never starts. Instead, the monitor turns on as if it got a signal, then immediately turns off. This loops on it's own indefinitely until I hold down power, hard reset it, and try again. Sometimes it works, sometimes it doesn't. I haven't tested much on the Ubuntu side. It appears that wifi works at least some of the time, but since I've had issues just getting to BIOS I'm not confident the issue is on the software side. I've also noticed issues with some of the USB ports no longer working, but that seems to be off and on. Finally, as of a few minutes ago, I booted to windows to discover that everything was running very slowly. Slow here is a relative word, but I have a Samsung 840 pro SSD and I'm used to applications running nigh instantly, and it was a solid 3 minutes before any of my applications would load. Anyway, my question is this: Is it likely that my motherboard is failing? Either way, what steps can I take to try and pin down the problem and figure out what to do?

  Read the article

• Sound doesn't work anymore after replacing RAM

  - by thejh

  Hello, today, I replaced one old RAM module with two newer, bigger ones, but now, the sound doesn't seem to work anymore. Already ran alsaconf and it didn't help. Output of lspci for the audio device: 00:07.0 Audio device: nVidia Corporation MCP67 High Definition Audio (rev a1) Subsystem: Giga-byte Technology Device a002 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 (500ns min, 1250ns max) Interrupt: pin A routed to IRQ 21 Region 0: Memory at f5100000 (32-bit, non-prefetchable) [size=16K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0 Enable- Address: 0000000000000000 Data: 0000 Masking: 00000000 Pending: 00000000 Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+ Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel The audio device is onboard and has six configurable outputs, two or so are also capable of being an input (if I remember it correctly), but I don't know how to control it under linux. Does somebody know how/whether replacing the RAM could be related to my problem and/or how to fix it?

  Read the article

• Strange boot problems on 6 month old setup

  - by Balefire

  I've already exhausted my knowledge on this one, so forgive me if this post is a bit long. I built a computer 6 months ago for my wife and it worked fine until last week. Then it randomly shut down and would lock up while trying to boot on the boot screen. I cleared cmos and it allowed me to do startup recovery, but it "failed to fix the issue" so I reinstalled windows on the HD (moving the old install to windows_old). It worked, so I started installing drivers again, but then when I restarted to finalize installations it locked up again. This time, I took the hard drive and hooked it up to my computer, backed up all her files, and then formatted the hard drive before reinstalling it. (again had to clear cmos to let me boot from disk) It installed windows, I installed drivers, and it worked for a few hours but then died during startup again. So, then I got a new HD, cleared cmos, and installed clean again, with the same result as the time before, it worked for a few hours, installed windows updates, then crashed on the 3rd or 4th time turning it on. I decided next to try reinstalling and then going online to see if there were any updates for the BIOS or drivers on the Motherboard, but now I can't get it to even bring up the boot menu, so now I'm just left wondering was it the motherboard, or is it the CPU, or the RAM? The problem was strangely intermittent so I thought it had to be a software issue, since a hardware issue would ALWAYS fail to boot, right? But now it seems to be a hardware issue, because it's not bringing up anything. Any suggestions? System: Windows 7 64-bit 970A-DS3 Gigabyte Motherboard AMD Phenom II X4 955 Deneb 3.2GHz Quad core Proc GeForce GT 430 (Fermi) 1GB Video Card 500W PSU 2 x G.SKILL Ripjaws X Series 4GB 240-Pin DDR3 1600 RAM

  Read the article

• GA-P55A-UD4 SYSFAN 2 problem....

  - by Vit

  Hi, I have some strange problems with the mobo in title. I have two fans connected to SYSFAN 1 and 2. Both are the same temp regulated Arctic Cooling F12. They are regulated thru temp sensor which is in different cable from fan. It connects to the 3 pin. So, I connected them to SYSFAN 1 and 2 MB ports. The problem is, when PC starts, the fan connected to SYSFAN 1 spins nice and is reporting speed to BIOS. But second fan connected to SYSFAN 2 starts to spin, than stops. I tried to warm the sensor with no help. Also, in BIOS I found no feature about SYSFAN 2 mode or something. I tried the fan itself by connecting it to PWR fan connector and it works fine. But obviously I want it to operate in SYSFAN 2. Please if you have any advice, help. Thanks.

  Read the article

• Bypass insane corporate security system

  - by user1665154

  I'm searching for a posibility to bypass the "Firewall" for 3-4 days. I've tried everything I know, so I ask here for a answer. We have no admin rights and the OS is Windows Vista There is an HTTP Proxy with NTML Authentication (only way to access the internet) It requires a username and password We use smart cards, in fact I have only a user number and a pin. Port 80 and 443 are open - I have an SSH server at home which is listening on port 443 The problem is that I need this proxy to connect to anything. Internet access only works in IE, Chrome, Firefox when I set the proxy settings to "use system proxy settings", "proxy-autoconfig (proxy.pac)" or when I enter the proxy inside the proxy.pac file. However I can't understand where they take the username and password which the Proxy requires. What I've tried was using cntlm to connect to the proxy with authentication (altought I have no PW and username) and PuTTY to create the SSH tunnel over port 443 whit the SOCKS Proxy which I've created with cntml. I've never found some SSH client which includes a "use system proxy settings" function.

  Read the article

• Fixing bent pins on a CPU

  - by Pekka

  While replacing a mainboard in a desktop machine (see related question), I did something stupid. I inserted the CPU into the new mainboard, but didn't check for the right position. When it didn't immediately lock in, I pressed slightly before realizing what was wrong. The result was a number of bent pins. I tried every tutorial that popped up when Googling "CPU bent pins" - using credit cards, sewing needles, and a hunting knife to get the pins back into position - but to no avail: For every pin I get straightened out, two others are bent. I have no problem getting individual pins straightened out, but my many attempts have led to many pins being slightly askew - enough for the CPU not to fit into the socket (An AMD X3 one). Maybe I just lack the motoric finesse. What I would need is some sort of a grid to fix all pins at once. It's a €50 processor so the loss is not catastrophic. But I thought before I go buy a new one, I thought I'd check here whether anybody knows some magic trick, or a cheap generally-available tool to fix this.

  Read the article

• Create taskbar shortcut to website in Window 7

  - by BJ292

  I'd like to create a shortcut to a website in Windows 7 on the taskbar that is not pinned to the default web browser. Currently if I drag the favicon from the left end of the firefox address bar to the Win 7 taskbar it will pin a shortcut to the firefox browser icon. Similarly if I create a shortcut on the desktop to a website and drag it to the taskbar it will also end up pinned to the firefox icon. The problem with this is to get to that shortcut I have to right click on the firefox icon and then select the pinned shortcut. That is workable for me but I want to do this for a child - so the shortcut needs to be right there on the taskbar as a stand-alone item. There is a workaround that pretty much solves the problem - create a new folder somewhere safe - create the shortcut to the website in the new folder - right click the taskbar and select toolbars - new toolbar - then browse to the folder you created and select it as the new toolbar. The contents of the folder will now appear on the taskbar as shortcuts. You need to drag it from the right hand end of the taskbar into the middle - turn off show titles and show text and make the icon large. I'd call this a 75% solution. Anyone know how to make a web shortcut that looks and operates just like any of the other shortcuts on the taskbar?

  Read the article

• Silverlight - Adding Text to Pushpin in Bing Maps via C#

  - by Morano88

  I was able to make my silverlight Bing map accepts Mousclicks and converts them to Pushpins in C#. Now I want to show a text next to the PushPin as a description that appears when the mouse goes over the pin , I have no clue how to do that. What are the methods that enable me to do this thing? This is the C# code : public partial class MainPage : UserControl { private MapLayer m_PushpinLayer; public MainPage() { InitializeComponent(); base.Loaded += OnLoaded; } private void OnLoaded(object sender, RoutedEventArgs e) { base.Loaded -= OnLoaded; m_PushpinLayer = new MapLayer(); x_Map.Children.Add(m_PushpinLayer); x_Map.MouseClick += OnMouseClick; } private void AddPushpin(double latitude, double longitude) { Pushpin pushpin = new Pushpin(); pushpin.MouseEnter += OnMouseEnter; pushpin.MouseLeave += OnMouseLeave; m_PushpinLayer.AddChild(pushpin, new Location(latitude, longitude), PositionOrigin.BottomCenter); } private void OnMouseClick(object sender, MapMouseEventArgs e) { Point clickLocation = e.ViewportPoint; Location location = x_Map.ViewportPointToLocation(clickLocation); AddPushpin(location.Latitude, location.Longitude); } private void OnMouseLeave(object sender, MouseEventArgs e) { Pushpin pushpin = sender as Pushpin; // remove the pushpin transform when mouse leaves pushpin.RenderTransform = null; } private void OnMouseEnter(object sender, MouseEventArgs e) { Pushpin pushpin = sender as Pushpin; // scaling will shrink (less than 1) or enlarge (greater than 1) source element ScaleTransform st = new ScaleTransform(); st.ScaleX = 1.4; st.ScaleY = 1.4; // set center of scaling to center of pushpin st.CenterX = (pushpin as FrameworkElement).Height / 2; st.CenterY = (pushpin as FrameworkElement).Height / 2; pushpin.RenderTransform = st; } }

  Read the article

• Common Access Card (CAC) Authentication Using Java

  - by Paul

  I'm bascially looking for someplace to start learning how to interface with a government CAC card using java. Ultimately, my goal is to find out how to use CAC card authentication (by PIN number) to authorize access to a website hosted using a Tomcat/J2EE server. But I'll need somewhere to start. So I figure I'd start by writing a small java program to simply read the CAC card information from the CAC card which is inserted into a card reader on my keyboard (DELL keyboard with CAC reader above the numeric keypad). By searching google, I found the cacard java project (https://cacard.dev.java.net/) which was replaced by the OpenSSO project. But I can't seem to find sample code of how to use it to connect to a card, read from a card, etc. Does anyone know where I can find some sample code so that I can start learning how to interact with a CAC card using java? Thanks EDIT: After researching more, I was thinking, would I be able to just set clientAuth="true" in the connector element in the server.xml file? http://tomcat.apache.org/tomcat-6.0-doc/ssl-howto.html clientAuth: Set this value to true if you want Tomcat to require all SSL clients to present a client Certificate in order to use this socket.

  Read the article

• MkMapView Zoom Level

  - by meetS

  I m using MkMapView with google maps.I succeed to show map view and address with annotation pin.But I want increased zoom level.How Can I Set it programmatically?? (void) showMyAddress { //Hide the keypad MKCoordinateRegion region; MKCoordinateSpan span; span.latitudeDelta=0.2; span.longitudeDelta=0.2; CLLocationCoordinate2D location = [self addressLocation]; region.span=span; region.center=location; if(addAnnotation != nil) { [mapView removeAnnotation:addAnnotation]; [addAnnotation release]; addAnnotation = nil; } addAnnotation = [[AddAnnotation alloc] initWithCoordinate:location ]; [addAnnotation setMTitle:@"abc"]; [addAnnotation setMSubTitle:@"def."] [mapView addAnnotation:addAnnotation]; [mapView setRegion:region animated:TRUE]; [mapView regionThatFits:region]; } -(CLLocationCoordinate2D) addressLocation { NSString *urlString = [NSString stringWithFormat:@"http://maps.google.com/maps/geo?q=%@&output=csv", [@"abc" stringByAddingPercentEscapesUsingEncoding:NSUTF8StringEncoding]]; NSString *locationString = [NSString stringWithContentsOfURL:[NSURL URLWithString:urlString] encoding:NSStringEncodingConversionAllowLossy error:nil]; NSArray *listItems = [locationString componentsSeparatedByString:@","]; double latitude = 0.0; double longitude = 0.0; if([listItems count] >= 4 && [[listItems objectAtIndex:0] isEqualToString:@"200"]) { latitude = [[listItems objectAtIndex:2] doubleValue]; longitude = [[listItems objectAtIndex:3] doubleValue]; } else { } CLLocationCoordinate2D location; location.latitude = latitude; location.longitude = longitude; return location; }

  Read the article

• How Do I Use jQuery/JavaScript To Open A Popup Window/Tab (ASPX Login Page) & Then Pass Values To Op

  - by Terry Robinson

  Hi All, We currently have two asp.net 2.x web applications and we need to perform the following functionality: From one application, we want to auto-login to the other web application automatically in a new tab; using the same browser instance/window. So the process is: Open New Window/Tab With Second System URL/Login Page Wait For Popup Window/Tab Page To Load (DOM Ready?) OnPopupDomReady { Get Usename, Password, PIN Controls (jQuery Selectors) and Populate In Code Then Click Login Button (All Programatically). } I am currently using JavaScript to Open the window as follows: <script type="text/javascript"> $(document).ready(function () { $('a[rel="external"]').click(function () { window.open($(this).attr('href')); return false; }); }); </script> I would like to use jQuery chaining functionality if possible to extent the method above so that I can attach a DOM Ready event to the popped up page and then use that event to call a method on the code behind of the popped up page to automatically login. Something similar to this (Note: The Following Code Sample Does Not Work, It Is Here To Try And Help Illustrate What We Are Trying To Achieve)... <script type="text/javascript"> $(document).ready(function () { $('a[rel="external"]').click(function () { window.open($(this).attr('href').ready(function () { // Use JavaScript (Pref. jQuery Partial Control Name Selectors) To Populate Username/Password TextBoxes & Click Login Button. }) }); }); </script> Our Architecture Is As Follows: We have the source for both products (ASP.NET WebSite[s]) and they are run under different app. pools in IIS. I hope this all makes sense, and if my plan is not going to work, please provide hints ;) Thanks All/Kind Regards, Terry Robinson.

  Read the article

• DirectSho GMFBridge not working as expected

  - by user1327407

  I am trying to understand why wont the source filter connect with VMR9? mediaController.InsertSourceFilter(sinkFilter, m_pRenderGraph, out sourceFilter); var vmr = new VideoMixingRenderer9(); m_pRenderGraph.AddFilter(vmr as IBaseFilter, "VMR"); IBaseFilter vmrBase = FilterGraphTools.FindFilterByClsid(m_pRenderGraph, Clsid.VideoMixingRenderer9); IVMRFilterConfig9 xd = vmrBase as IVMRFilterConfig9; if (xd != null) { int status = xd.SetRenderingMode(VMR9Mode.Windowless); } FilterGraphTools.ConnectFilters(m_pRenderGraph, sourceFilter, vmrBase, true); mediaController.BridgeGraphs(sinkFilter, sourceFilter); Without going into too much detail: Line „ConnectFilters“ fails because no intermediate filters are found to make that connection work. When trying to debug, I can clearly see that Source filter is not spitting out anything useful. (It’s like that the sink<--source transfer never works), so that’s why it wont connect. However, when I get source filter „Output 1“ pin, and then use myGraph.Render(source_output_pin), it works. Data is being sent from sink to source and everything connects automatically. However the problem is that the wrong VMR is inserted there. It’s VMR Renderer. I would like to have VMR9, that’s why im doing it. Why wont it work with VMR9 and why does source filter not show correct media type. Thank you.

  Read the article

• WinForms Application Form "Shakes" When Audio Playing

  - by ikurtz

  I have a C# game program that i'm developing. it uses sound samples and winsock. when i test run the game most of the audio works fine but from time to time if it is multiple samples being played sequentially the application form shakes a little bit and then goes back to its old position. how do i go about debugging this or present it to you folks in a manageable manner? i'm sure no one is going to want the whole app code in fear of virus attacks. please guide me.. EDIT: i have not been able to pin down any code section that produces this result. it just does and i cannot explain it. EDIT: no the x/y position are not changing. the window like shakes around a few pixels and then goes back to the position were it was before the shake. if (audio) { Stream stream; SoundPlayer player; stream = Properties.Resources.ResourceManager.GetStream("_home"); player = new System.Media.SoundPlayer(stream); player.PlaySync(); player.Dispose(); string ShipID = fireResult.DestroyedShipType.ToString(); stream = Properties.Resources.ResourceManager.GetStream("_" + ShipID); player = new System.Media.SoundPlayer(stream); player.PlaySync(); player.Dispose(); stream = Properties.Resources.ResourceManager.GetStream("_destroyed"); player = new System.Media.SoundPlayer(stream); player.PlaySync(); player.Dispose(); } can you see anything in the above code that would produce this shake?

  Read the article

• Default values for Content Taxonomy fields in Drupal with Hierarchical Select widget

  - by lazysoundsystem

  I'm trying to set the default value for a Content Taxonomy field in a hook_form_alter, but can't pin down the necessary format. I've tried this and many variations: foreach (element_children($form) as $child) { // Set $default_value. if ($form[$child]['tids']) { // This, for Content Taxonomy fields, isn't working: $form[$child]['tids']['#default_value'] = array('value' => $default_value); dsm($form[$child]['tids']['#default_value']); } else { // This, for other fields, is working: $form[$child][0]['#default_value']['value'] = $default_value; } } Can anyone tell me what I'm missing? Edit: In response to Henrik Opel (thanks for getting involved), here is the print out of the relevant field of the form with my changes to the default fields commented out, showing the '#default_value' field I'm trying to influence. It also shows that the option widget I'm using is Hierarchical Select (could this be a factor?). In the dsm() in the code above, the changes to the default value are recognised, but they don't get processed later on. field_name_of_content_taxonomy_field (Array, 3 elements) #tree (Boolean) TRUE #weight (String, 1 characters ) 5 tids (Array, 7 elements) #title (String, 10 characters ) Vocabulary_name #type (String, 19 characters ) hierarchical_select #weight (String, 1 characters ) 5 #config (Array, 15 elements) // 15 elements here #required (String, 1 characters ) 0 #description (String, 0 characters ) #default_value (Array, 0 elements)

  Read the article

• iPhone: addAnnotation not working when called from another view

  - by Nic Hubbard

  I have two views, the first view has an MKMapView on it named ridesMap. The second view is just a view with a UITableView in it. When you click the save button in the second view, it calls a method from the first view: // Get my first views class MyRidesMapViewController *rideMapView = [[MyRidesMapViewController alloc] init]; // Call the method from my first views class that removes an annotation [rideMapView addAnno:newRidePlacemark.coordinate withTitle:rideTitle.text withSubTitle:address]; This correctly calls the addAnno method, which looks like: - (void)addAnno:(CLLocationCoordinate2D)anno withTitle:(NSString *)annoTitle withSubTitle:(NSString *)subTitle { Annotation *ano = [[[Annotation alloc] init] autorelease]; ano.coordinate = anno; ano.title = annoTitle; ano.subtitle = subTitle; if ([ano conformsToProtocol:@protocol(MKAnnotation)]) { NSLog(@"YES IT DOES!!!"); } [ridesMap addAnnotation:ano]; }//end addAnno This method creates an annotation which does conform to MKAnnotation, and it suppose to add that annotation to the map using the addAnnotation method. But, the annotation never gets added. I NEVER get any errors when the annotation does not get added. But it never appears when the method is called. Why would this be? It seems that I have done everything correctly, and that I am passing a correct MKAnnotation to the addAnnotation method. So, I don't get why it never drops a pin? Could it be because I am calling this method from another view? Why would that matter?

  Read the article

• ARMv6 FIQ, acknowledge interrupt

  - by fastmonkeywheels

  I'm working with an i.mx35 armv6 core processor. I have Interrupt 62 configured as a FIQ with my handler installed and being called. My handler at the moment just toggles an output pin so I can test latency with a scope. With the code below, once I trigger the FIQ it continues forever as fast as it can, apparently not being acknowledged. I'm triggering the FIQ by means of the Interrupt Force Register so I'm assured that the source isn't triggering it this fast. If I disable Interrupt 62 in the AVIC in my FIQ routine the interrupt only triggers once. I have read the sections on the VIC Port in the ARM1136JF-S and ARM1136J-S Technical Reference Manual and it covers proper exit procedure. I'm only having one FIQ handler so I have no need to branch. The line that I don't understand is: STR R0, [R8,#AckFinished] I'm not sure what AckFinished is supposed to be or what this command is supposed to do. My FIQ handler is below: ldr r9, IOMUX_ADDR12 ldr r8, [r9] orr r8, #0x08 @ top LED str r8,[r9] @turn on LED bic r8, #0x08 @ top LED str r8,[r9] @turn off LED subs pc, r14, #4 IOMUX_ADDR12: .word 0xFC2A4000 @remapped IOMUX addr My handler returns just fine and normal system operation resumes if I disable it after the first go, otherwise it triggers constantly and the system appears to hang. Do you think my assumption is right that the core isn't acknowledging the AVIC or could there be another cause of this FIQ triggering?

  Read the article

• Why isn't my new object being seen? C#

  - by Dan

  I am getting ready to take a class at a college on C#. I have been reading up on it a lot and decided to start a fun project. Here is what my project consists of: Main Control Form Configuration Form Arduino Program.cs calls Configuration.cs at start. This is where pin modes for the Arduino are set and where a timer is set. When I set these values, they get sent to MainControl.cs. When I hit the "Save" button in Configuration.cs, a MainControl.cs object is created [[I am correct in that?]] All of those values that were sent by Configuration.cs had corresponding setters that set private static variables in MainControl.cs [[ I don't really know if that is the preferred way, I am most definetly open to any suggestion anyone has]] MainControl.cs uses its default constructor, and this constructor calls a method that creates an arduino object from one of the private variables (serialPort) [[ Using this Arduino class Firmata.NET ]] When the arduino object is created, I know (I guess I do) because the form takes a few seconds to come up (As opposed to not using serial port) My problem is this: I do not understand why nothing can see the object I have been very wordy, I apologize if I wasn't concise. Here is the code: public partial class CMainControl : Form { private static string serialPort; public CMainControl() { InitializeComponent(); createArduino(); updateConfig(); // Change label values to values set in configuration } private void createArduino() { Arduino arduino = new Arduino(serialPort); } In Configuration.cs, when I set the serial port through a combobox, the value is sent to MainControl.cs just fine. Here is the error I get: Error 1 The name 'arduino' does not exist in the current context C:\Programming\Visual Studio\Workhead Demo\Workhead Demo\CMainControl.cs 94 13 Workhead Demo Please let me know if anyone can help and/or offer pointers, and please let me know if I didn't post or format anything correctly. Thank you very much :)

  Read the article

• Autocomplete and IE7 - slowness, sluggishness as overall pagesize grows?

  - by wchrisjohnson

  Hi, I have the autocomplete plugin (http://bassistance.de/jquery-plugins/jquery-plugin-autocomplete/, version 1.1 and 1.0.2) on a project to add pieces of "equipment" to a "project". On a fresh project the plugin works great; the data returned from the database comes back FAST, you can scroll the list fast, and can select an item and move on to the next one. Once I have a project established with equipment on it, and I go to add equipment, the performance is pretty bad. It takes 4-5 seconds to get the list of data back from the server, scrolling the list is painful, and the cursor takes several seconds to settle on an item. Repainting the page after the list goes away is slow. This is occurring in IE7, latest version. FF3 and Chrome are fine, very snappy. The pagesize is about 40K overall. I'm thinking this is an issue with the IE7 Javascript engine, or an edge case with this plugin and IE7; it works quickly enough in FF3+. I would appreciate any ideas, solutions, known issues, or thoughts on how to more specifically pin this down. I'd love to post sample code, but this is a corporate app, and I'm not how useful it would be given that the server side piece cannot be shown; ie: you can't pull it down and test it like a self contained piece of code.. Thanks in advance! Chris

  Read the article

• C# client to Java web service

  - by tomislavg

  I have received wsdl file from outside company. I'm using VS2005 c#. With wsdl.exe I have created class containing methods and types for the given web service. To connect to the service outside company requires that certificate from the smart card is inputed in the header. I think i have achieved this with service.ClientCertificates.Add("Path to exported cert" - at least for now, after probably later i will take it from Certificate Store When service is called there are three steps that are taken and visible by the Fidller(Web Debugging Proxy)). service is called on the url http://test.company.com/webservice.wsdl service redirects the request to certificate server and pin needs to be inputed to get cookie for the server service is again redirected to url http://test.company.com/webservice.wsdl At point 1. I can see that my request send to the server contains .... but at point 3. i can not see request` just a empty string. The exception is thrown Msg: Possible SOAP version mismatch: Envelope namespace http://schemas.xmlsoap.org/wsdl/ was unexpected. Expecting http://schemas.xmlsoap.org/soap/envelope/. Does somebody have an example how to connect to java web service with certificate and AlowRedirect enabled for the web service? Any ideas what i am doing wrong are more that welcome.

  Read the article

• Can't access annotation property of subclassed uibutton

  - by Tzur Gazit

  I have a mapView to which I add annotations. The pin's callout have a button (rightCalloutAccessoryView). In order to be able to display various information when the button is pushed, i've subclassed uibutton and added a class called "Annotation". @interface CustomButton : UIButton { NSIndexPath *indexPath; Annotation *mAnnotation; } @property (nonatomic, retain) NSIndexPath *indexPath; @property (nonatomic, copy) Annotation *mAnnotation; - (id) setAnnotation2:(Annotation *)annotation; @end Here is "Annotation": @interface Annotation : NSObject <MKAnnotation> { CLLocationCoordinate2D coordinate; NSString *mPhotoID; NSString *mPhotoUrl; NSString *mPhotoName; NSString *mOwner; NSString *mAddress; } @property (nonatomic, assign) CLLocationCoordinate2D coordinate; @property (nonatomic, copy) NSString *mPhotoID; @property (nonatomic, copy) NSString *mPhotoUrl; @property (nonatomic, copy) NSString *mPhotoName; @property (nonatomic, copy) NSString *mOwner; @property (nonatomic, copy) NSString *mAddress; - (id) initWithCoordinates:(CLLocationCoordinate2D)coordinate; - (id) setPhotoId:(NSString *)id url:(NSString *)url owner:(NSString *)owner address:(NSString *)address andName:(NSString *)name; @end I want to set the annotation property of the uibutton at - (MKAnnotationView *)mapView:(MKMapView *)pMapView viewForAnnotation:(id )annotation, in order to refer to it at the button push handler (-(IBAction) showDetails:(id)sender). The problem is that I can't set the annotation property of the button. I get the following message at run time: 2010-04-27 08:15:11.781 HotLocations[487:207] *** -[UIButton setMAnnotation:]: unrecognized selector sent to instance 0x5063400 2010-04-27 08:15:11.781 HotLocations[487:207] *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '*** -[UIButton setMAnnotation:]: unrecognized selector sent to instance 0x5063400' 2010-04-27 08:15:11.781 HotLocations[487:207] Stack: ( 32080987, 2472563977, 32462907, 32032374, 31884994, 55885, 30695992, 30679095, 30662137, 30514190, 30553882, 30481385, 30479684, 30496027, 30588515, 63333386, 31865536, 31861832, 40171029, 40171226, 2846639 ) I appreciate the help. Tzur.

  Read the article

• Method return type

  - by sarah xia

  Hi, In my company, a system is designed to have 3 layers. Layer1 is responsible for business logic handling. Layer3 is calling back end systems. Layer2 sits between the two layers so that layer1 doesn't need to know about the back end systems. To replay information from layer3, layer2 needs to define interface to layer1. For example, layer1 wants to check if a PIN from user is correct. It calls layer2 checkPin() method and then layer2 calls the relevant back end system. The checkPin() results could be: correctPin, inCorrectPin and internalError. At the moment, we defined the return type 'int'. So if layer2 returns 0, it means correctPin; if 1 is returned, it means inCorrectPin; if 9 is returned it means internalError. It works. However I feel a bit uneasy about this approach. Are there better ways to do it? For example define an enum CheckPinResult{CORRECT_PIN,INCORRECT_PIN,INTERNAL_ERROR}, and return CheckPinResult type? Thanks, Sarah

  Read the article

• VEMap and a GeoRSS feed(hosted separately)

  - by Alexis Abril

  The scenario is as follows: A WCF web service exists that outputs a valid GeoRSS feed. This lives in its own domain as a number of different applications have access to it. A web page(on a different site) has been created with an instance of a VEMap(Bing/Virtual Earth map object). Now, VEMap can accept an input feed in this format via the following: var layer = new VEShapeLayer(); var veLayerSpec = new VEShapeSourceSpecification(VEDataType.GeoRSS, "someurl", layer); map.ImportShapeLayerData(veLayerSpec, onComplete, true); onComplete is a callback function I'm using to replace the default pin graphic with something custom. The question is in regards to "someurl", which is a path to a local xml file containing the geographic information(georss simple format). I've realized this feed and the map must be hosted in the same domain, so I've created a generic handler that reads the remote feed and returns it in the same format. var veLayerSpec = new VEShapeSourceSpecification(VEDataType.GeoRSS, "/somelocalhandler.ashx", layer); When I do this, I get the VEMap error("z is null"). This is the same error one would receive when trying to access a remote feed. When I copy the feed into a local xml file(ie, "feed.xml") there is no error. The order of operations is currently: remote feed - local handler - VEMap import If I'm over complicating this procedure, let me know! I'm a bit new to the Bing Maps API and might have missed something. Any assistance is appreciated.

  Read the article

• ASP.NET MVC View ReRenders Part of Itself

  - by Jason

  In all my years of .NET programming I have not run across a bug as weird as this one. I discovered the problem because some elements on the page were getting double-bound by jQuery. After some (ridiculous) debugging, I finally discovered that once the view is completely done rendering itself and all its children partial views, it goes back to an arbitrary yet consistent location and re-renders itself. I have been pulling my hair out about this for two days now and I simply cannot get it to render itself only once! For lack of any better debugging idea, I've painstakingly added logging tracers throughout the HTML just so I can pin down what may be causing this. For instance, this code ($log just logs to the console): ... <script type="text/javascript">var x = 0; $log('1');</script> <div id="new-ad-form"> <script type="text/javascript">x++;$log('1.5', x);</script> ... will yield ... <--- this happens before this snippet 1 1.5 1 ... 10 <--- bottom of my form, after snippet 1.5 2 <--- beginning of part that runs again! ... 9 <--- this happens after this snippet I've searched my codebase high and low, but there is NOTHING that says that it should re-render part of a page. I'm wondering if the jQueryUI has anything to do with it, as #new-ad-form is the container for a jQueryUI dialog box. If this is potentially the case, here's my init code for that: $('#new-ad-form').dialog({ autoOpen: false, modal: true, width: 470, title: 'Create A New Ad', position: ['center', 35], close: AdEditor.reset });

  Read the article

• PayPal integration woes: PDT hangs on return to site

  - by Tom

  Hi, I'm implementing PayPal IPN & PDT. After some headache & time at the sandbox, IPN is working well and PDT returns the correct $_GET data. The implementation is as follows: Pass user ID in form to PayPal User buys product and triggers IPN which updates database for given user ID PDT returns transaction ID when user returns to site The return page says "please wait" and repeat-Ajax-checks for the transaction status User is redirected to success/failure page Everything works well, EXCEPT that when using the PayPal ready PHP code for PDT to do a return POST, the page hangs. PayPal waits for a response and the user never gets back to my site. I'm not getting a fail status, just nothing. The funny thing is that once the unknown error occurs, my test domain becomes unresponsive for a short period. The code (PHP): https://www.paypal.com/us/cgi-bin/webscr?cmd=p/xcl/rec/pdt-code-outside If I comment out the POST back, it all works fine. I'm able to pin down the problem to once the code enters the while{} loop. Unfortunately, I'm not experienced enough to write a replacement from scratch for the PayPal code, so would really appreciate any ideas on what might be wrong. The POST back goes to ssl://www.sandbox.paypal.com, and I'm using button code and an authorisation token that have all been created via a sandbox test account. Thanks in advance.

  Read the article

• Where should you put 3rd party .NET dlls when using git submodules to avoid duplication

  - by Tim Abell

  I have two .NET library projects in Visual Studio 2008 that both make use of the MySql Connector for .NET (MySql.Data.dll). These libraries are then in turn both used by a .NET command line application which also uses the Connector. The library projects are pulled in to the application's solution as git submodules and referenced by project in Visual Studio. I'm looking for the most effective strategy for storing and referencing the MySql Connector library. I have tried having the MySql.Data.dll checked in to all three projects (in their root folder), this was problematic when one project changed to a newer version of the connector dll. Although each project had its own version of the dll, only one was packaged into the resultant application leading to an API mismatch which was hard to pin down. This has put me off this approach. I have tried having the command line application reference the connector dll that is held in a submodule, however this only removes the possibility of version mismatches when there is only one submodule rather than two as in this case. I am contemplating putting the dll in the global assembly cache (GAC) of all machines that need to build or use the application, but I'm wary of not having all dependencies for an application available in source control.

  Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30  | Next Page >