Search Results

Search found 9381 results on 376 pages for 'wireless driver'.

Page 25/376 | < Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • wireless ethernet adapter with EAP-PEAP?

    - by Joseph
    We have a wireless network set up to support WPA or WPA2 with AES or TKIP encryption and EAP-PEAP authentication. Users are wanting to connect devices that don't have the ability to do EAP-PEAP but have ethernet ports. I have found a wireless printer server that can do this, but I have yet to find a wireless ethernet adapter that can. Has anyone seen one with this ability?

    Read the article

  • Wireless router DSL connection problem help

    - by infoquad
    I recently bought a wireless DSL router to replace my wired one. After quick setup however, the router does not connect to the Internet. Wireless connection between laptop and router exists and Internet can be connected through laptop(manually) by using router as WAN miniport(PPPoE). What I want to do is connect the wireless router to Internet so that when laptop connects to router, I can start using the Internet. How do I do this? Please help.

    Read the article

  • Wireless Connection unstable when multiple devices connected

    - by KingIsulgard
    My wireless network works perfectly when only 1 device is connected. Super fast, full strength. But as soon as multiple devices are connected to the wireless network the connections become unstable (constantly losing connection). It's quite annoying. I have a Sitecom Wireless 300N XR Gigabit Router WL-306, which should be a decent router so I'm guessing there must be something wrong with my configuration. Does any of you know what might cause this? Thanks

    Read the article

  • Where are Wireless Profiles stored in Ubuntu

    - by LonnieBest
    Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

    Read the article

  • Linux will not activate wireless after device has been re-enabled

    - by XHR
    Using a Eee 900A netbook by Asus. By pressing Fn + F2, I can disable or enable the wireless chip on the netbook, a blue LED indicates the status. I've been able to connect to wireless networks just fine with this netbook. However, if the wireless chip ever becomes disabled, I have to reboot to get my network connection back. This generally happens when suspending. For some reason the LED will be off and I have to hit Fn + F2 for it to light up again. However, after doing so, Linux will not reconnect to the network. It simply changes the wireless status from "wireless is disabled" to "device not ready". Even worse, I've recently had issues with the chip being enabled at boot, thus making it nearly impossible to get connected. I've searched around on-line but haven't found much of anything useful on this. This happens on all kinds of different distros including Ubuntu 9.10 Netbook, EeeBuntu 4 beta, Jolicloud and Ubuntu 10.04 Netbook. Edit I noticed this question is getting a lot of views. To give a quick update, I never did resolve this issue with the given distro's. However, I'm currently running Ubuntu 10.10 netbook edition and this issue has gone away.

    Read the article

  • Lynksys WRT120N wireless router not connecting to ADSL

    - by pradeetp
    I have a lynksys WRT120N wireless router that was connected to Sterlite ADSL modem. The internet connection was working fine through wireless access. I changed the ADSL router because it developed some power issues and got it replaced with the same model/brand from the service provider. However I am not able to access internet now. Here is the current setting Sterlite SAM300 XA IP Address: 192.168.2.1 (I changed it to this IP because the IP address of my ADSL router was same) Lynksys WRT120N wireless router IP Address: 192.168.1.1 If I connect my laptop to ADSL router directly, the internet works fine. It is only that that if I access it wirelessley through wireless router that I am not able to connect to internet. The IP address setting has been configured to obtain IP address automatically. I have windows 7 OS home edition. Could someone please help me to fix this issue.

    Read the article

  • Wireless option grayed out in Windows Mobility Center

    - by thomasvdb
    We currently have a Lenovo ThinkPad L512 which can't connect to wireless networks. He simply indicates he can't find any networks. Other notebooks (also ThinkPad L512-notebooks) in the company do find the network so nothings wrong with the configuration of the wireless router. As indicated on answer.microsoft.com, I should check Windows Mobility Center and enable the entry "Turn Wireless On". Unfortunately this option has been grayed out. How can I enable this option? There isn't a physical switch on the laptop to turn on the wireless.

    Read the article

  • DriverManager always returns my custom driver regardless of the connection URL

    - by JGB146
    I am writing a driver to act as a wrapper around two separate MySQL connections (to distributed databases). Basically, the goal is to enable interaction with my driver for all applications instead of requiring the application to sort out which database holds the desired data. Most of the code for this is in place, but I'm having a problem in that when I attempt to create connections via the MySQL Driver, the DriverManager is returning an instance of my driver instead of the MySQL Driver. I'd appreciate any tips on what could be causing this and what could be done to fix it! Below is a few relevant snippets of code. I can provide more, but there's a lot, so I'd need to know what else you want to see. First, from MyDriver.java: public MyDriver() throws SQLException { DriverManager.registerDriver(this); } public Connection connect(String url, Properties info) throws SQLException { try { return new MyConnection(info); } catch (Exception e) { return null; } } public boolean acceptsURL(String url) throws SQLException { if (url.contains("jdbc:jgb://")) { return true; } return false; } It is my understanding that this acceptsURL function will dictate whether or not the DriverManager deems my driver a suitable fit for a given URL. Hence it should only be passing connections from my driver if the URL contains "jdbc:jgb://" right? Here's code from MyConnection.java: Connection c1 = null; Connection c2 = null; /** *Constructors */ public DDBSConnection (Properties info) throws SQLException, Exception { info.list(System.out); //included for testing Class.forName("com.mysql.jdbc.Driver").newInstance(); String url1 = "jdbc:mysql://server1.com/jgb"; String url2 = "jdbc:mysql://server2.com/jgb"; this.c1 = DriverManager.getConnection( url1, info.getProperty("username"), info.getProperty("password")); this.c2 = DriverManager.getConnection( url2, info.getProperty("username"), info.getProperty("password")); } And this tells me two things. First, the info.list() call confirms that the correct user and password are being sent. Second, because we enter an infinite loop, we see that the DriverManager is providing new instances of my connection as matches for the mysql URLs instead of the desired mysql driver/connection. FWIW, I have separately tested implementations that go straight to the mysql driver using this exact syntax (al beit only one at a time), and was able to successfully interact with each database individually from a test application outside of my driver.

    Read the article

  • Java DriverManager Always Assigns My Driver

    - by JGB146
    I am writing a driver to act as a wrapper around two separate MySQL connections (to distributed databases). Basically, the goal is to enable interaction with my driver for all applications instead of requiring the application to sort out which database holds the desired data. Most of the code for this is in place, but I'm having a problem in that when I attempt to create connections via the MySQL Driver, the DriverManager is returning an instance of my driver instead of the MySQL Driver. I'd appreciate any tips on what could be causing this and what could be done to fix it! Below is a few relevant snippets of code. I can provide more, but there's a lot, so I'd need to know what else you want to see. First, from MyDriver.java: public MyDriver() throws SQLException { DriverManager.registerDriver(this); } public Connection connect(String url, Properties info) throws SQLException { try { return new MyConnection(info); } catch (Exception e) { return null; } } public boolean acceptsURL(String url) throws SQLException { if (url.contains("jdbc:jgb://")) { return true; } return false; } It is my understanding that this acceptsURL function will dictate whether or not the DriverManager deems my driver a suitable fit for a given URL. Hence it should only be passing connections from my driver if the URL contains "jdbc:jgb://" right? Here's code from MyConnection.java: Connection c1 = null; Connection c2 = null; /** *Constructors */ public DDBSConnection (Properties info) throws SQLException, Exception { info.list(System.out); //included for testing Class.forName("com.mysql.jdbc.Driver").newInstance(); String url1 = "jdbc:mysql://server1.com/jgb"; String url2 = "jdbc:mysql://server2.com/jgb"; this.c1 = DriverManager.getConnection( url1, info.getProperty("username"), info.getProperty("password")); this.c2 = DriverManager.getConnection( url2, info.getProperty("username"), info.getProperty("password")); } And this tells me two things. First, the info.list() call confirms that the correct user and password are being sent. Second, because we enter an infinite loop, we see that the DriverManager is providing new instances of my connection as matches for the mysql URLs instead of the desired mysql driver/connection. FWIW, I have separately tested implementations that go straight to the mysql driver using this exact syntax (al beit only one at a time), and was able to successfully interact with each database individually from a test application outside of my driver.

    Read the article

  • Connecting multiple access points

    - by mohsen farahanipoor
    I'm working on a big project. We want to create a wireless network throughout the building with 15 floors. My idea is that we should set up one unified wireless access point at least in each floor...in case of signal attenuate, we use Access point extender/repeater. I selected DWL-6600AP from among D-Link industrial access points. I want to implement a single wireless LAN throughout the building. Is it possible to combines multiple DWL-6600 access points to achieving just a single WLAN? Can a wireless switch controller do this task? Can these Access Points interfere with each other? What is the solution? I read D-Link website's learning materials, but I am still confused. My other question is around the connecting these APs to Wireless Switch Controller - Is it possible to use power line for connecting DWL-6600 to Wireless Switch Controller device? My main goal is that clients with portable devices such as laptops should be easily connected to the network to share & have communication without any more manual configuration as they are already connected to a single network.

    Read the article

  • Wifi hotspot disconnected after some time

    - by Rohit Bansal
    I am trying to use my Ubuntu system as Wifi Hotspot, but for some reason Hotspot get disconnected on its own. Searching for the solution, I found this help : Why is my ethernet connection connecting and disconnecting repeatedly? Reading through the above article I used the following command sudo killall dnsmasq as a result I manage to establish hotspot for around 5-10 sec before getting disconnected as against immediately.... Here's the system log (in case needed) tail -f /var/log/syslog : Apr 1 23:31:42 NetworkManager[901]: <info> Starting dnsmasq... Apr 1 23:31:42 NetworkManager[901]: <info> (wlan0): device state change: ip-config -> activated (reason 'none') [70 100 0] Apr 1 23:31:42 dnsmasq[4159]: started, version 2.57 cachesize 150 Apr 1 23:31:42 dnsmasq[4159]: compile time options: IPv6 GNU-getopt DBus I18N DHCP TFTP IDN Apr 1 23:31:42 dnsmasq-dhcp[4159]: DHCP, IP range 10.42.43.10 -- 10.42.43.100, lease time 1h Apr 1 23:31:42 dnsmasq[4159]: reading /etc/resolv.conf Apr 1 23:31:42 dnsmasq[4159]: using nameserver 220.226.6.104#53 Apr 1 23:31:42 dnsmasq[4159]: using nameserver 220.226.100.40#53 Apr 1 23:31:42 dnsmasq[4159]: cleared cache Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) successful, device activated. Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete. Apr 1 23:31:42 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP4 Configure Get) complete. Apr 1 23:31:42 dbus[885]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Apr 1 23:31:42 dbus[885]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Connection established at this point....now disconnecting after 10 sec... Apr 1 23:31:52 ntpdate[4194]: adjust time server 91.189.94.4 offset -0.011589 sec Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): IP6 addrconf timed out or failed. Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) scheduled... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) started... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) started... Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --out-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --out-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --source 10.42.43.0/255.255.255.0 --in-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --destination 10.42.43.0/255.255.255.0 --out-interface wlan0 --match state --state ESTABLISHED,RELATED --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table nat --insert POSTROUTING --source 10.42.43.0/255.255.255.0 ! --destination 10.42.43.0/255.255.255.0 --jump MASQUERADE Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 53 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol tcp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert INPUT --in-interface wlan0 --protocol udp --destination-port 67 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --out-interface wlan0 --jump REJECT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --in-interface wlan0 --out-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --source 10.42.43.0/255.255.255.0 --in-interface wlan0 --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table filter --insert FORWARD --destination 10.42.43.0/255.255.255.0 --out-interface wlan0 --match state --state ESTABLISHED,RELATED --jump ACCEPT Apr 1 23:32:01 NetworkManager[901]: <info> Executing: /sbin/iptables --table nat --insert POSTROUTING --source 10.42.43.0/255.255.255.0 ! --destination 10.42.43.0/255.255.255.0 --jump MASQUERADE Apr 1 23:32:01 NetworkManager[901]: <info> Starting dnsmasq... Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 5 of 5 (IP Configure Commit) complete. Apr 1 23:32:01 NetworkManager[901]: <info> Activation (wlan0) Stage 4 of 5 (IP6 Configure Timeout) complete. Apr 1 23:32:01 NetworkManager[901]: <warn> dnsmasq died with signal 9 Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): device state change: activated -> failed (reason 'sharing-start-failed') [100 120 18] Apr 1 23:32:01 dnsmasq[4235]: started, version 2.57 cachesize 150 Apr 1 23:32:01 dnsmasq[4235]: compile time options: IPv6 GNU-getopt DBus I18N DHCP TFTP IDN Apr 1 23:32:01 dnsmasq-dhcp[4235]: DHCP, IP range 10.42.43.10 -- 10.42.43.100, lease time 1h Apr 1 23:32:01 NetworkManager[901]: <warn> Activation (wlan0) failed for access point (Reppify Ubuntu) Apr 1 23:32:01 dnsmasq[4235]: reading /etc/resolv.conf Apr 1 23:32:01 dnsmasq[4235]: using nameserver 220.226.6.104#53 Apr 1 23:32:01 dnsmasq[4235]: using nameserver 220.226.100.40#53 Apr 1 23:32:01 dnsmasq[4235]: cleared cache Apr 1 23:32:01 NetworkManager[901]: <warn> Activation (wlan0) failed. Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] Apr 1 23:32:01 NetworkManager[901]: <info> (wlan0): deactivating device (reason 'none') [0] Apr 1 23:32:01 dbus[885]: [system] Activating service name='org.freedesktop.nm_dispatcher' (using servicehelper) Apr 1 23:32:01 dbus[885]: [system] Successfully activated service 'org.freedesktop.nm_dispatcher' Apr 1 23:32:01 NetworkManager[901]: <error> [1333303321.565351] [nm-device-wifi.c:1815] nm_device_wifi_set_mode(): (wlan0): error setting mode 2

    Read the article

  • Logitech Unify... how to use both the keyboard abd mouse on the same receiver?

    - by simon
    I bought this keyboard : tinyurl.com/7g3l2wt and this mouse : tinyurl.com/7kvkldm I am trying to use both on the same receiver, but so far i can't figure it out! i have tried this : https://github.com/treeder/logitech_unifier But i don't know how to compile it! if i paste ' gcc -o unify unify.c ' in the terminal, then i got this: gcc: erreur: unify.c: Aucun fichier ou dossier de ce type gcc: erreur fatale: pas de fichier à l'entrée compilation terminée. sorry it is in french... it say no files of this type and no file in the input... anyone can tell me how to compile it and then find my hidraw devices?? thanks

    Read the article

  • How to setup a wifi ap hotspot with ipv6 support?

    - by keyman
    How to setup a wifi ap (access point mode) hotspot, with IPv6 support? I've set up a hotspot according to the guide to wifi ap hotspot setup and it works fine. But via the hotspot I failed to visit IPv6 websites. How can I setup a hotspot able to share Ipv6 Internet access? Thanks! Further: Actually I've tried to setup IPv6 forwarding and masquerading. First enabling IPv6 forwarding: echo 1 | sudo tee net/ipv6/conf/default/forwarding Then I tried to execute: sudo ip6tables -t nat -A POSTROUTING -s 2001:db8:0:1::/64 -o eth0 -j MASQUERADE But it gave me an error: ip6tables v1.4.12: Couldn't load target `MASQUERADE':No such file or directory I searched through the Internet but I get confused. So I'm here for help. Thanks!

    Read the article

  • possible missing firmware

    - by pdd
    the other day i removed my linux-firmware package by mistake, i tried reinstalling it but i get this error: E: /var/cache/apt/archives/linux-firmware_1.60_all.deb: trying to overwrite '/lib/firmware/rt73.bin', which is also in package firmware-ralink 0.14+lenny2 the code from the terminal is: (Reading database ... 235747 files and directories currently installed.) Unpacking linux-firmware (from .../linux-firmware_1.60_all.deb) ... dpkg: error processing /var/cache/apt/archives/linux-firmware_1.60_all.deb (--unpack): trying to overwrite '/lib/firmware/rt73.bin', which is also in package firmware-ralink 0.14+lenny2 No apport report written because MaxReports is reached already dpkg-deb: error: subprocess paste was killed by signal (Broken pipe) Errors were encountered while processing: /var/cache/apt/archives/linux-firmware_1.60_all.deb E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover:

    Read the article

  • Broadcom WiFi drivers conflict

    - by james
    $ sudo dpkg -i wireless-bcm43142-dkms-6.20.55.19_amd64.deb dpkg: acerca de wireless-bcm43142-dkms-6.20.55.19_amd64.deb que contiene wireless-bcm43142-oneiric-dkms: wireless-bcm43142-oneiric-dkms entra en conflicto con bcmwl-kernel-source bcmwl-kernel-source (versión 6.20.155.1+bdcom-0ubuntu0.0.2) está presente y instalado. dpkg: error al procesar wireless-bcm43142-dkms-6.20.55.19_amd64.deb (--install): paquetes en conflicto - no se instalará wireless-bcm43142-oneiric-dkms Se encontraron errores al procesar: wireless-bcm43142-dkms-6.20.55.19_amd64.deb Help me find a solution to install this .deb package.

    Read the article

  • Sony Vaio PCG-71315L "Wireless is disabled by hardware switch" Help!

    - by Luke Rossi
    I'm a new user to Ubuntu and Linux as a whole, I've had it for a few months and just as I'm starting to get a feel for things my wireless decided to quit on me. This puzzled me so i checked all the switches on the Vaio; my wireless switch was on (my bluetooth was also working), and in my windows partition the problem is non-existent. Help please? Anyways after executing the "rfkill list" command this was the outcome: 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no 2: sony-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 4: hci0: Bluetooth Soft blocked: no Hard blocked: no As stated in the title my laptop is a Sony Vaio PCG-71315L

    Read the article

  • How do I get wireless working on a Dell Inspiron 510m?

    - by user17449
    Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

    Read the article

  • How do I select Wireless radio portions in Ubuntu?

    - by Ryan McClure
    Bear with me, to be honest I have no idea what Wireless radio portions are.... At my school, I was told my the user support that the wireless network in my dorm uses 801.11 A/B/G/N. For some reason, the wireless in my room doesn't work. However, other buildings use only A/B/G, they say. In any other building, my wireless works fine. How do I tell my system to use the G portion only? (As requested by user support in the email I received). Here are the various logs/output requested: dmesg lshw -c network lsmod

    Read the article

  • How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

    - by Ivan Kreimer
    I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

    Read the article

  • How can I make NetworkManager ignore my wireless card?

    - by ændrük
    I do not want NetworkManager to list or manipulate my wireless card. Can I hide its interface from NetworkManager somehow? I have tried adding this in /etc/network/interfaces, iface wlan0 inet static address 192.168.1.101 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid Synaptotagmin pre-up wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf post-down killall -q wpa_supplicant and this in /etc/NetworkManager/nm-system-settings.conf, [keyfile] unmanaged-devices=/org/freedesktop/Hal/devices/net_00_19_e0_57_86_af but NetworkManager Applet still lists and allows me to connect to wireless networks.

    Read the article

  • How do I disable the "enable/disable wireless" shortcut key on my laptop?

    - by Matthew
    On my Dell Studio XPS 16, I sometimes accidentally hit this key. Wireless becomes disabled, and hitting it again does not re-enable wireless. I have to hit it an odd number of times, then restart my computer to re-enable wireless. I can't imagine a situation in which I would want to disable wireless from my keyboard. Is it possible just disable the key all-together, so I can avoid this problem? On a related note, what package do I file the bug against? I'm happy just disabling the key, but that's really just a workaround.

    Read the article

  • How do I get my Lenovo T61 to connect to a wireless network?

    - by Ross Fleming
    I have a Lenovo Thinkpad T61 and the wireless works just fine so I installed Ubuntu straight away only to find that the wireless will not connect, it will see the networks but just not connect. Has anyone managed to solve this all the forums seem to relate to Ubuntu 9.04 and before. Edit:Sorry about that, I didn't realise that there were 2 models mine is the Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection. Any help is much appreciated.

    Read the article

  • How can I make NetworkManager ignore my wireless card?

    - by ændrük
    I do not want NetworkManager to list or manipulate my wireless card. Can I hide its interface from NetworkManager somehow? I have tried adding this in /etc/network/interfaces, iface wlan0 inet static address 192.168.1.101 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid Synaptotagmin pre-up wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf post-down killall -q wpa_supplicant and this in /etc/NetworkManager/nm-system-settings.conf, [main] plugins=ifupdown,keyfile [ifupdown] managed=false [keyfile] unmanaged-devices=/org/freedesktop/Hal/devices/net_00_19_e0_57_86_af but NetworkManager Applet still lists and allows me to connect to wireless networks.

    Read the article

< Previous Page | 21 22 23 24 25 26 27 28 29 30 31 32  | Next Page >