Search Results

Search found 31421 results on 1257 pages for 'software performance'.

Page 250/1257 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

  • Jumbo Frames, ISCSI and ESXi

    - by vlannoob
    I have enabled Jumbo Frames (9000) in ESXi for all my vmNICs, vmKernels, vSwitches, iSCSI Bindings etc - basically anywhere in ESXi where it has an MTU settings I have put 9000 in it. The ports on the switches (Dell PowerConnects) are all set for Jumbo Frames. I have a Dell MD3200i with 2 controllers, each with 4 ports for iSCSI. Each of these ports is set to Jumbo Frames (9000) as well. So now the questions: Do I need to log into each Windows Server VM I am running and delve into the NIC properties and manually set it to Jumbo Frames in the NIC properties in the device Manager as well? Whats the best way of testing that Jumbo Frames are indeed working as intended?

    Read the article

  • misaligned raid partition in Ubuntu 10.04

    - by Linux Jedi
    I attached two identical hard drives to my linux machine. Then using gparted I formated the first 1024 mb at the beginning of each drive as linux swap space. Then I went into system-administration-disk utility. In there I went to file-create-RAID array. I selected the remaining space in each of the two identical hard drives and created a striped raid array. After the array was created, a warning message appeared. It said "The partition is misaligned by 522240 bytes. This may result in very poor performance. Repartitioning is suggested." What do I do now? As far as I can tell, the partitions are identical.

    Read the article

  • Intel Core 2 Duo E6600 versus AMD Athlon II X2 3GHZ

    - by Billy ONeal
    Hello :) I have an Intel Core 2 Duo E6600 (2.4GHZ) in my current desktop, and I have a newer machine with an AMD Athlon II X2 3.0GHZ. I'm wondering how the systems will perform in comparison to one another. I'd like to use the AMD because it's 45nm and uses less power, but I don't want to do so at a loss in perforamnce. Which should perform better? Billy3

    Read the article

  • What is the computer "doing" when it is running slow and task manager is not showing any CPU activity?

    - by Joakim Tall
    Typical example is when shutting down a memoryintensive application. It can take quite a while before the computer gets back up to speed. Is there some inherent cost in releasing memory? Or is it throttled by some kind of harddrive activity, and if so is there any good way to track that? I usually bring up task manager when a computer is running slow, and usually sorting by cpu activity can show what process is causing the problem, but sometimes there is no activity showing. And yes I "show processes from all users", I have been wondering this since the days win2k :)

    Read the article

  • Optimal disk partitions for database setup (15 Drives)

    - by Jason
    We are setting up a new database system and have 15 drives to play with (+2 on-board for the OS). With a total of 15 drives would it be better to setup all 14 as one RAID-10 block (+1 hot spare) OR split into two RAID-10 sets one for Data (8 disks) and one for logs/backups (6 disks). My question boils down to the following: is there a specific point where having more drives in a RAID-10 setup will out preform having the drives broken into smaller RAID-10 sets.

    Read the article

  • sys.dm_exec_query_stats interaction with recompilation

    - by Sam Saffron
    We use sys.dm_exec_query_stats to track down slow queries and queries that are IO offenders. This works great, we get a lot of very insightful stats. It is clear this is not as accurate as running a profiler trace, as you have no idea when SQL Server will decide to chuck out a an execution plan. We have quite a few queries where the wrong execution plan is cached. For example queries like the following: SELECT TOP 30 a.Id FROM Posts a JOIN Posts q ON q.Id = a.ParentId JOIN PostTags pt ON q.Id = pt.PostId WHERE a.PostTypeId = 2 AND a.DeletionDate IS NULL AND a.CommunityOwnedDate IS NULL AND a.CreationDate @date AND LEN(a.Body) 300 AND pt.Tag = @tag AND a.Score 0 ORDER BY a.Score DESC The problem is that the ideal plan really depends on the date selected (screenshot of ideal plan): However if the wrong plan is cached, it totally chokes when the date range is big: (notice the big fat lines) To overcome this we were recommended to use either OPTION (OPTIMIZE FOR UNKNOWN) or OPTION (RECOMPILE) OPTIMIZE FOR UNKNOWN results in a slightly better plan, which is far from optimal. Executions are tracked in sys.dm_exec_query_stats. RECOMPILE results in the best plan being chosen, however no execution counts and stats are tracked in sys.dm_exec_query_stats. Is there another DMV we could use to track stats on queries with OPTION (RECOMPILE)? Is this behavior by-design? Is there another way we can for recompilation while keeping stats tracked in sys.dm_exec_query_stats? Note: the framework will always execute parameterized queries using sp_executesql

    Read the article

  • SQL Server Full Text Search resource consumption

    - by Sam Saffron
    When SQL Server builds a fulltext index computer resources are consumed (IO/Memory/CPU) Similarly when you perform full text searches, resources are consumed. How can I get a gauge over a 24 hour period of the exact amount of CPU and IO(reads/writes) that fulltext is responsible for, in relation to global SQL Server resource usage. Are there any perfmon counters, DMVs or profiler traces I can use to help answer this question?

    Read the article

  • How dow I remove 1.000.000 WebsiteCache directories?

    - by harper
    I found that in a WebsiteCache directory more than 1.000.000 subdirectories has been created. I want to remove all these directories. My first approach was to use the command line tool: cd WebsiteCache rmdir /Q /S . This will remove all subdirectories except WebsiteCache itself, since it is the current working directory. I noticed after two hours that the directoriws starting with A-H have been removed. Why does rmdir removes the directories in alphabetical order? It must take additional effort to do this ordered. What is a fast way to deleted such an amount of directories?

    Read the article

  • Soundtest works, but no other sounds and windows starts very slowly

    - by Kristian Kari
    So suddenly all sounds on my computer stopped working expect the sound test works, but when I go to control panel and audio it says there's no audio device. And audio players and audio on website doesn't work either. and Also windows starts very slowly. I'm not sure if this helps but I'll tell what happened before this. I downloaded this program from a little shady website, I hesitated and for a good reason I guess cos the moment I finished downloading it, my antivir detected it as unwanted program and put it on quarantine. I thought everything was fine, but had some problems with program (won't go to details about it cos it's not really related to audio) so rebooted the computer and I was suprised that windows started really really slowly. It took like 5 mins to load the desktop such. After that I noticed the sounds were missing, I immediately deleted the program since I thought it was causing the problem. But it didn't change much. I tried to find the solution with no success and now I'm just scanning again my computer. I'd be thankful if anyone would be able to help me. I might have left a thing or ten things out, so feel free to ask. oh and I'm using windows xp

    Read the article

  • CPU and HD degradation on sourced based Linux distribution

    - by danilo2
    I was wondering for a long time if source based Linux distributions, like Gentoo or Funtoo are "destroying" your system faster than binary ones (like Fedora or Debian). I'm talking about CPU and hard drive degradation. Of course, when you're updating your system, it has to compile everything from source, so it takes longer and your CPU is used at hard conditions (it is warmer and more loaded). Such systems compile hundreds of packages weekly, so does it really matter? Does such a system degrade faster than binary based ones?

    Read the article

  • How to calculate required switch speed based on network usage?

    - by tobefound
    I have a 48 port HP Procurve Switch 2610 (J9088A) that can handle 13.0 million PPS (packets per second) and features wire speed switching capacity at 17.6Gbps. First off, what does that REALLY mean? Where do I start when trying to figure out if my office (with 70 employees) will be well setup with this switch? How to calculate through-put based on a user average load of X MB per day? 90% of the folks will only be sending email, access random websites, etc... the other 10% will be conducting heavier tasks like moving image files (10 MB) across network shares, constant external FTP streams through the switch to a server etc... Is this switch good enough?

    Read the article

  • What is fastest way to backup a disk image over LAN?

    - by David Balažic
    Sometimes I boot sysrescd or a similar live linux on a PC to backup the hardrive over local network to my server. I noticed many times, that the transfer speed is not optimal (slower than HDD and network speed). Any rules of thumb what to do and what to avoid? What I typically do is something like: dd bs=16M if=/dev/sda | nc ... # on client nc ... | dd bs=16M of=/destination/disk/backup1 # on server I also "throw" in lzop (other are way too slow) and sometimes on the fly md5sum calculation (both of uncompressed and compress source). I try to add (m)buffer (or other alternatives) to improve throughput (and get a progress indicator). I noticed that even with enough free CPU, adding commands to the pipeline slows things down. Typically the destination is on a NTFS volume (accessed via ntfs-3g, with the _big_writes_ option).

    Read the article

  • My laptop suppose to have 6 GB ram but it's only 2 GB installed

    - by monablo
    My laptop is supposed to have 6 GB ram but it only detects 2 GB of it, so I don't know what to do. I searched the web for answer and what i get that there's 2 possible problem: 1- That 4 GB ram card is broken and not working 2- or the 2 ram card have a different path so the windows chose the path of the smaller ram card which would be the 2 GB ram I don't know what is the path in first place so I really don't know what to do. How would I troubleshoot, and work out why the 4 GB stick is not being detected? My laptop's specifications are as follows: Windows 7 Home premium 64- bit Operating system processor : intel (R) core(TM) i7 CPU Q740 @1.73 GHz 1.73GHz installed memory(RAM) : 2.00 GB (but it suppose to be 6 GB -_- ) My laptop is Dell and it's Model N5010

    Read the article

  • Ultra-lightweight web browser?

    - by zildjohn01
    Are there any good super-lightweight graphical web browsers out there? I'd like to be able to browse the web on an old PC, but the mainstream crop of browsers is just too heavy, and I don't want to resort to something like Lynx. There must be something decent out there that'll fit in 16 or 32MB of RAM comfortably. 100% standards compliance isn't necessary, but I'd like something that supports the most widely used parts of CSS and JavaScript. The goal is to get 98% of sites usable in a nice, graphical format.

    Read the article

  • Improve file transfer speed between Windows PCs and servers

    - by Geotarget
    I've setup a server which I've connected to multiple PCs in my workplace. Sadly, data transfer speeds are at max 3 MB/sec per connection which works out slow for file transfers, especially when transferring large files. I'm using Windows filesharing and the server is a Windows Server 2008 (2 Ghz CPU, 1 GB RAM) and the client PCs mostly running Windows 7. How can I detect bottlenecks in my network and improve file sharing speed within the network?

    Read the article

  • Avoid Windows Explorer to load complete executable file

    - by eli.work
    On Windows Vista, when browsing to a network folder containing executables, Windows Explorer seems to load all the files completely just to be able to show the executable icon (the resource monitor indicates loads of traffic during the loading of the directory) On XP only a part of the file is loaded. Is there a way to avoid the complete loading of these files? Note that disabling my anti virus does not help.

    Read the article

  • What are possible causes of keyboard lag on my desktop machine?

    - by Jer
    I am running Windows 7 and began experiencing keyboard lag in most applications, and it seems to be getting worse. Certain websites are the worst - on some, I can type a sentence, take my hands off the keyboard, and watch the characters continue to appear on the screen for several seconds. Others are not as bad, but still noticeable and annoying. I just started noticing it in non-browser applications (e.g. Outlook) as well. I've disabled all extensions in Firefox, rebooted my machine, and that did nothing. There is nothing using much memory or cpu cycles, even when the lag is occurring. This is a machine at work with very strict controls over what can be installed, so the chances of any kind of malware are very slim. I don't believe anything as been installed since before the problem started. What could be causing this, and/or what can I do to debug?

    Read the article

  • How to monitor IO svctm with every 5 mins frequency using nagios?

    - by sabya
    I want to collect samples of iostat's svctm, await every 5 mins from all of my servers and store them in nagios. I want to get the values for what is happening in every 5 minutes (not since boot time, iostat's first output gives values since boot time). How can I do it in nagios? EDIT The tps should NOT be calculated #of transactions happened since reboot divided by uptime. What I want is # of transferred happened in last X mins divided X*60.

    Read the article

  • Losing SQL connections

    - by john pavelka
    sql servr 2005 - Standard; one dedicated sql server (VM); windows server 2003; Small databases; About once a week we lose all sql connections. It seems to fix itself after about 5-10 minutes. System.Web.HttpUnhandledException: Exception of type 'System.Web.HttpUnhandledException' was thrown. --- System.Data.SqlClient.SqlException: Timeout expired. The timeout period elapsed prior to completion of the operation or the server is not responding. We don't have a fully qualified DBA; it's kind of a joint effort here. Can somebody give me some general ideas for troubleshooting the network side and the application side? We already ran a few tuning profiles and ran through Database Tuning Advisor to apply indexing recommendations. It would sure be nice if there was a way to take a snapshot of what was running on sql server when these 100% cpu spikes occured, but sometimes we're not around. Is it common to throttle CPU for certain processes? Can this be done with Windows server 2003? For example, if security apps were making cpu spike to 100%, is there a way to limit their cpu usage? Any advice is appreciated. thanks,

    Read the article

  • iptables, blocking large numbers of IP Addresses

    - by Twirrim
    I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

    Read the article

  • Ngingx max worker_connections and access log

    - by MotoTribe
    I'm troubleshoot an issue with my site. I'm seeing in the ngingx-error.log that the max worker_connection limit has been reached when the site went down. I'm not seeing an increase of requests during that time in the ngingx-access.log. Does that mean the mysql database had a bottleneck at that time that caused the requests to queue up? Or would it not log any requests that where made after the max worker_connection limit has been reached?

    Read the article

  • MySQL hangs if connection comes from outside the LAN

    - by Subito
    I have a MySQL Server operating just fine if I access him from his local LAN (192.168.100.0/24). If I try to access hin from another LAN (192.168.113.0/24 in this case) it hangs for a really long time before delivering the result. SHOW PROCESSLIST; shows this process in Sleep, State empty. If I strace -p this process I get the following Output (23512 is the PID of the corresponding mysqld process): Process 23512 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...>) = 1 fcntl(10, F_GETFL) = 0x2 (flags O_RDWR) fcntl(10, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(10, {sa_family=AF_INET, sin_port=htons(51696), sin_addr=inet_addr("192.168.113.4")}, [16]) = 33 fcntl(10, F_SETFL, O_RDWR) = 0 rt_sigaction(SIGCHLD, {SIG_DFL, [CHLD], SA_RESTORER|SA_RESTART, 0x7f9ce7ca34f0}, {SIG_DFL, [CHLD], SA_RESTORER|SA_RESTART, 0x7f9ce7ca34f0}, ) = 0 getpeername(33, {sa_family=AF_INET, sin_port=htons(51696), sin_addr=inet_addr("192.168.113.4")}, [16]) = 0 getsockname(33, {sa_family=AF_INET, sin_port=htons(3306), sin_addr=inet_addr("192.168.100.190")}, [16]) = 0 open("/etc/hosts.allow", O_RDONLY) = 64 fstat(64, {st_mode=S_IFREG|0644, st_size=580, ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f9ce9839000 read(64, "# /etc/hosts.allow: list of host"..., 4096) = 580 read(64, "", 4096) = 0 close(64) = 0 munmap(0x7f9ce9839000, 4096) = 0 open("/etc/hosts.deny", O_RDONLY) = 64 fstat(64, {st_mode=S_IFREG|0644, st_size=880, ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f9ce9839000 read(64, "# /etc/hosts.deny: list of hosts"..., 4096) = 880 read(64, "", 4096) = 0 close(64) = 0 munmap(0x7f9ce9839000, 4096) = 0 getsockname(33, {sa_family=AF_INET, sin_port=htons(3306), sin_addr=inet_addr("192.168.100.190")}, [16]) = 0 fcntl(33, F_SETFL, O_RDONLY) = 0 fcntl(33, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(33, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0", 16) = 0 setsockopt(33, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0", 16) = 0 fcntl(33, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(33, SOL_IP, IP_TOS, [8], 4) = 0 setsockopt(33, SOL_TCP, TCP_NODELAY, [1], 4) = 0 futex(0x7f9cea5c9564, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0x7f9cea5c9560, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0x7f9cea5c6fe0, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=10, revents=POLLIN}]) fcntl(10, F_GETFL) = 0x2 (flags O_RDWR) fcntl(10, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(10, {sa_family=AF_INET, sin_port=htons(51697), sin_addr=inet_addr("192.168.113.4")}, [16]) = 31 fcntl(10, F_SETFL, O_RDWR) = 0 rt_sigaction(SIGCHLD, {SIG_DFL, [CHLD], SA_RESTORER|SA_RESTART, 0x7f9ce7ca34f0}, {SIG_DFL, [CHLD], SA_RESTORER|SA_RESTART, 0x7f9ce7ca34f0}, ) = 0 getpeername(31, {sa_family=AF_INET, sin_port=htons(51697), sin_addr=inet_addr("192.168.113.4")}, [16]) = 0 getsockname(31, {sa_family=AF_INET, sin_port=htons(3306), sin_addr=inet_addr("192.168.100.190")}, [16]) = 0 open("/etc/hosts.allow", O_RDONLY) = 33 fstat(33, {st_mode=S_IFREG|0644, st_size=580, ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f9ce9839000 read(33, "# /etc/hosts.allow: list of host"..., 4096) = 580 read(33, "", 4096) = 0 close(33) = 0 munmap(0x7f9ce9839000, 4096) = 0 open("/etc/hosts.deny", O_RDONLY) = 33 fstat(33, {st_mode=S_IFREG|0644, st_size=880, ...}) = 0 mmap(NULL, 4096, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x7f9ce9839000 read(33, "# /etc/hosts.deny: list of hosts"..., 4096) = 880 read(33, "", 4096) = 0 close(33) = 0 munmap(0x7f9ce9839000, 4096) = 0 getsockname(31, {sa_family=AF_INET, sin_port=htons(3306), sin_addr=inet_addr("192.168.100.190")}, [16]) = 0 fcntl(31, F_SETFL, O_RDONLY) = 0 fcntl(31, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(31, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0", 16) = 0 setsockopt(31, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0", 16) = 0 fcntl(31, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(31, SOL_IP, IP_TOS, [8], 4) = 0 setsockopt(31, SOL_TCP, TCP_NODELAY, [1], 4) = 0 futex(0x7f9cea5c9564, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0x7f9cea5c9560, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0x7f9cea5c6fe0, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1^C <unfinished ...> Process 23512 detached This output repeats itself until the answer gets send. It could take up to 15 Minutes until the request gets served. In the local LAN its a matter of Milliseconds. Why is this and how can I debug this further? [Edit] tcpdump shows a ton of this: 14:49:44.103107 IP cassandra-test.mysql > 192.168.X.6.64626: Flags [S.], seq 1434117703, ack 1793610733, win 14600, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0 14:49:44.135187 IP 192.168.X.6.64625 > cassandra-test.mysql: Flags [P.], seq 106:145, ack 182, win 4345, length 39 14:49:44.135293 IP cassandra-test.mysql > 192.168.X.6.64625: Flags [P.], seq 182:293, ack 145, win 115, length 111 14:49:44.167025 IP 192.168.X.6.64624 > cassandra-test.mysql: Flags [.], ack 444, win 4280, length 0 14:49:44.168933 IP 192.168.X.6.64626 > cassandra-test.mysql: Flags [.], ack 1, win 4390, length 0 14:49:44.169088 IP cassandra-test.mysql > 192.168.X.6.64626: Flags [P.], seq 1:89, ack 1, win 115, length 88 14:49:44.169672 IP 192.168.X.6.64625 > cassandra-test.mysql: Flags [P.], seq 145:171, ack 293, win 4317, length 26 14:49:44.169726 IP cassandra-test.mysql > 192.168.X.6.64625: Flags [P.], seq 293:419, ack 171, win 115, length 126 14:49:44.275111 IP 192.168.X.6.64626 > cassandra-test.mysql: Flags [P.], seq 1:74, ack 89, win 4368, length 73 14:49:44.275131 IP cassandra-test.mysql > 192.168.X.6.64626: Flags [.], ack 74, win 115, length 0 14:49:44.275149 IP 192.168.X.6.64625 > cassandra-test.mysql: Flags [P.], seq 171:180, ack 419, win 4286, length 9 14:49:44.275189 IP cassandra-test.mysql > 192.168.X.6.64626: Flags [P.], seq 89:100, ack 74, win 115, length 11 14:49:44.275264 IP 192.168.X.6.64625 > cassandra-test.mysql: Flags [P.], seq 180:185, ack 419, win 4286, length 5 14:49:44.275281 IP cassandra-test.mysql > 192.168.X.6.64625: Flags [.], ack 185, win 115, length 0 14:49:44.275295 IP cassandra-test.mysql > 192.168.X.6.64625: Flags [F.], seq 419, ack 185, win 115, length 0 14:49:44.275650 IP 192.168.X.6.64625 > cassandra-test.mysql: Flags [F.], seq 185, ack 419, win 4286, length 0 14:49:44.275660 IP cassandra-test.mysql > 192.168.X.6.64625: Flags [.], ack 186, win 115, length 0 14:49:44.275910 IP 192.168.X.6.64627 > cassandra-test.mysql: Flags [S], seq 2336421549, win 8192, options [mss 1351,nop,wscale 2,nop,nop,sackOK], length 0 14:49:44.275921 IP cassandra-test.mysql > 192.168.X.6.64627: Flags [S.], seq 3289359778, ack 2336421550, win 14600, options [mss 1460,nop,nop,sackOK,nop,wscale 7], length 0

    Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >