Search Results

Search found 37048 results on 1482 pages for 'whole line'.

Page 250/1482 | < Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >

  • What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

    - by eater
    I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

    Read the article

  • Problems configuring logstash for email output

    - by user2099762
    I'm trying to configure logstash to send email alerts and log output in elasticsearch / kibana. I have the logs successfully syncing via rsyslog, but I get the following error when I run /opt/logstash-1.4.1/bin/logstash agent -f /opt/logstash-1.4.1/logstash.conf --configtest Error: Expected one of #, {, ,, ] at line 23, column 12 (byte 387) after filter { if [program] == "nginx-access" { grok { match = [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} [%{HTTPDATE:time_local}] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded = false host = " Here is my logstash config file input { syslog { type => syslog port => 5544 } } filter { if [program] == "nginx-access" { grok { match => [ "message" , "%{IPORHOST:remote_addr} - %{USERNAME:remote_user} \[% {HTTPDATE:time_local}\] %{QS:request} %{INT:status} %{INT:body_bytes_sent} %{QS:http_referer} %{QS:http_user_agent}” ] } } } output { stdout { } elasticsearch { embedded => false host => "localhost" cluster => "cluster01" } email { from => "[email protected]" match => [ "Error 504 Gateway Timeout", "status,504", "Error 404 Not Found", "status,404" ] subject => "%{matchName}" to => "[email protected]" via => "smtp" body => "Here is the event line that occured: %{@message}" htmlbody => "<h2>%{matchName}</h2><br/><br/><h3>Full Event</h3><br/><br/><div align='center'>%{@message}</div>" } } I've checked line 23 which is referenced in the error and it looks fine....I've tried taking out the filter, and everything works...without changing that line. Please help

    Read the article

  • Why is crontab giving "No such file or directory" error when the file DOES exist?

    - by fettereddingoskidney
    I am getting the following three lines in an error message in /var/mail/username after the following job runs in crontab... 15 * * * * /Applications/MAMP/htdocs/iconimageryidx/includes/insertPropertyRESI.php Errors: /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 1: ?php: No such file or directory /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 3: syntax error near unexpected token `'initialize.php'' /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 3: `require_once('initialize.php'); The PHP script I am trying to execute DOES in fact exist, and I have made absolutely sure the spelling is correct several times. I ran a crontab on another script before and it worked just fine...any ideas?? The 2nd & 3rd Errors are from line 3 in the following script (the one I am trying to run with the crontab): <?php require_once('initialize.php'); require_once('insertPropertyTypes.php'); $sDate; if(isset($_GET['startDate'])) { $sDate = $_GET['startDate']; } else { $sDate = ''; } $insertResi = new InsertPropertyTypes('Listing', $sDate, 'RESI'); ?> When I run my script insertPropertyRESI.php in the browser, it runs just fine???? Also, initialize.php and insertPropertyTypes.php are in the same directory as insertPropertyRESI.php I am using MAMP with PHP 5.3.5 thakns for the help :?

    Read the article

  • Why do moving lines become fuzzy on my monitor?

    - by CodeInChaos
    I recently got a new notebook. With moving images there are some graphical issues, and I'd like to know what causes them. None of my earlier monitors exhibited similar issues. Moving high contrast lines become jagged, similar to interleaved videos. When moving a horizontal line vertically those artifacts are colored, when moving a vertical line horizontally they aren't colored. The effect isn't observable in static images. And when moving faster the zone in which it occurs becomes wider. The effect is very visible if I move a window around on the borders of the window and wherever high contrast lines appear. But it appears when watching videos too. The vertical line in that image moves to the right, the horizontal line upwards. The effect is most likely related to the fact that each real pixel consists of different sub-pixels for the different color channels. But how are these causing the observed effect? Is the change at which the different colors change to the destination brightness different? The optical impression is that every second pixel in a chess board like arrangement is adapting slower than it's neighbors. But that doesn't make much sense.

    Read the article

  • Postfix : outgoing mail in TLS for a specific domain

    - by vercetty92
    I am trying to configure postfix to send mail in TLS (starttls in fact), but only for a specific destination. I tried with "smtp_tls_policy_maps". This is the only line in my main.cf file regarding TLS configuration, but it seems not working. Here is my main.cf file: queue_directory = /opt/csw/var/spool/postfix command_directory = /opt/csw/sbin daemon_directory = /opt/csw/libexec/postfix html_directory = /opt/csw/share/doc/postfix/html manpage_directory = /opt/csw/share/man sample_directory = /opt/csw/share/doc/postfix/samples readme_directory = /opt/csw/share/doc/postfix/README_FILES mail_spool_directory = /var/spool/mail sendmail_path = /opt/csw/sbin/sendmail newaliases_path = /opt/csw/bin/newaliases mailq_path = /opt/csw/bin/mailq mail_owner = postfix setgid_group = postdrop mydomain = ullink.net myorigin = $myhostname mydestination = $myhostname, localhost.$mydomain, localhost masquerade_domains = vercetty92.net alias_maps = dbm:/etc/opt/csw/postfix/aliases alias_database = dbm:/etc/opt/csw/postfix/aliases transport_maps = dbm:/etc/opt/csw/postfix/transport smtp_tls_policy_maps = dbm:/etc/opt/csw/postfix/tls_policy inet_interfaces = all unknown_local_recipient_reject_code = 550 relayhost = smtpd_banner = $myhostname ESMTP $mail_name debug_peer_level = 2 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin xxgdb $daemon_directory/$process_name $process_id & sleep 5 And here is my "tls_policy" file: gmail.com encrypt protocols=SSLv3:TLSv1 ciphers=high I also tried gmail.com encrypt My wish is to use TLS only for the gmail domain. With this configuration, I don't see any TLS line in the source of the mail. But if I tell postfix to use TLS if possible for all destination with this line, it works: smtp_tls_security_level = may Beause I can see this line in the source of my mail: (version=TLSv1/SSLv3 cipher=OTHER); But I don't want to try to use TLS for the others domains...only for gmail... Do I miss something in my conf? (I also try whith "hash:/etc/opt/csw/postfix/tls_policy", and it's the same) Thanks a lot in advance

    Read the article

  • Google Drive terminates without error on startup

    - by Iszi
    I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

    Read the article

  • Amavisd-new(2.6.4-3) failing to do "lookup_sql_dsn" when large number of emails are need to be accessed

    - by sandip
    Amavis is failing to do sql lookup when large number of emails are sent to amavis. Its throwing out error after scanning 40 to 50 email. It shows error like. (!!)TROUBLE in process_request: sql exec: err=7, 57P01,DBD::Pg::st bind_param failed:FATAL: terminating connection due to administrator command\nSSL connection has been closed unexpectedly at (eval 103) line 164, <GEN50> line 5. at (eval 104) line 280, <GEN50> line 5. As soon as this error appears in the logs, Amavis stops and port 10024 is closed. Thinking it to an error due to ssl connection in the database(postgresql-8.4), i had stopped ssl in postgres, but it was of no use. I have tried to configure amavis on another server, but i got the same error again. This happening on a production server, So i am not being able to scan emails as per user settings. Anybody have any idea, what may be the source of this error ?? Please help. Thanks in advance

    Read the article

  • How do I activate the F_LINE input in a transplanted HP chassis?

    - by admin
    I have an HP Pavilion Media Center PC chassis, vintage 2003 or so and I replaced the motherboard in it with a newer (vintage 2009) HP motherboard, M2N68-LA (Narra 5). I have scoured the internet trying to find pinouts for the motherboard to no avail. My question concerns the front panel audio, specifically Line In. The old chassis was built for AC97 but the new mobo is build for the newer HD audio standard. I figured out by comparison & experimentally how to connect the Mic & Headphone jacks to the HD audio header of the mobo by adding a manual switch to set the SENSE lines. Now all works fine for Mic & headphone. The old chassis also has a front panel Line In jack that the newer HP chassis does not have. However, the new mobo has a 4 pin white connector labeled F_LINE that I believe is a line input. Under Windows 7 I see the two Line Inputs in the mixer but I can't get one of them to become active. The 4 pin F_LINE connector uses the two middle pins for ground, and presumably the other two for left and right audio inputs. There are no pins for sensing on that connector. Can anyone tell me how to use that F_LINE input for the front panel, or how to activate it?

    Read the article

  • What may be wrong with String::ToIdentifier::EN tests?

    - by wk01
    I try to install Perl module String::ToIdentifier::EN (as depndency of DBIx::Class::Schema::Loader) but it fails on tests. I googled those errors but get no picture, where is problem: Building and testing String-ToIdentifier-EN-0.07 cp lib/String/ToIdentifier/EN.pm blib/lib/String/ToIdentifier/EN.pm cp lib/String/ToIdentifier/EN/Unicode.pm blib/lib/String/ToIdentifier/EN/Unicode.pm Manifying blib/man3/String::ToIdentifier::EN.3pm Manifying blib/man3/String::ToIdentifier::EN::Unicode.3pm PERL_DL_NONLAZY=1 /usr/bin/perl "-MExtUtils::Command::MM" "-e" "test_harness(0, 'inc', 'blib/lib', 'blib/arch')" t/00_basic.t t/10_ascii.t t/20_capitalization.t Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 25 tests but ran 4. # Looks like your test exited with 25 just after 4. t/00_basic.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 21/25 subtests Byte order is not compatible at ../../lib/Storable.pm (autosplit into ../../lib/auto/Storable/_retrieve.al) line 380, at /home/wanradt/perl5/lib/perl5/Lingua/EN/Tagger.pm line 167 # Looks like you planned 768 tests but ran 512. # Looks like your test exited with 25 just after 512. t/10_ascii.t ........... Dubious, test returned 25 (wstat 6400, 0x1900) Failed 256/768 subtests t/20_capitalization.t .. ok Test Summary Report ------------------- t/00_basic.t (Wstat: 6400 Tests: 4 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 25 tests but ran 4. t/10_ascii.t (Wstat: 6400 Tests: 512 Failed: 0) Non-zero exit status: 25 Parse errors: Bad plan. You planned 768 tests but ran 512. Files=3, Tests=528, 1 wallclock secs ( 0.07 usr 0.02 sys + 0.42 cusr 0.04 csys = 0.55 CPU) Result: FAIL Failed 2/3 test programs. 0/528 subtests failed. make: *** [test_dynamic] Error 255 -> FAIL Installing String::ToIdentifier::EN failed. See /home/wanradt/.cpanm/build.log for details. Byte order is not compatible at... seems a key, but to where?

    Read the article

  • How to import this data set into excel? (column headings on each row delimited by a colon)

    - by Anonymous
    I'm trying to import the following data set into Excel. I've had no luck with the text import wizard. I'd like Excel to make id, name, street, etc the column names and insert each record onto a new row. , id: sdfg:435-345, name: Some Name, type: , street: Address Line 1, Some Place, postalcode: DN2 5FF, city: Cityhere, telephoneNumber: 01234 567890, mobileNumber: 01234 567890, faxNumber: /, url: http://www.website.co.uk, email: [email protected], remark: , geocode: 526.2456;-0.8520, category: some, more, info , id: sdfg:435-345f, name: Some Name, type: , street: Address Line 1, Some Place, postalcode: DN2 5FF, city: Cityhere, telephoneNumber: 01234 567890, mobileNumber: 01234 567890, faxNumber: /, url: http://www.website.co.uk, email: [email protected], remark: , geocode: 526.2456;-0.8520, category: some, more, info Is there any easy way to do this with Excel? I'm struggling to think of a way to convert this to a conventional CSV easily. As far as I can think, I'd have to remove the labels from each line, enclose each line in quotes, then delimit them with commas. Obviously that's made a little more difficult to script though seeing as some fields (address, for instance) contain comma-delimited data. I'm not good with regex at all. What's the best way to tackle this?

    Read the article

  • How to automatically start VM created by virt-manager?

    - by Jeff Shattock
    I have created a virtual machine with virt-manager that runs on kvm/qemu. The machine works well when started through virt-manager. However, I would like to be able to start and stop the VM through a script in init.d, so that it comes up and down along with the host. I need to have virt-manager show that the machine is running, and to be able to connect to its console through there. When I use the command line that is produced by running ps -eaf | grep kvm after starting the vm through virt-manager, I get some console messages about redirected character devices, but the machine does start and runs properly. However, I do not get any indication from virt-manager that it has started. How can I modify the command line to get virt-manager to pick up the running VM? Is there anything else about the command line that should change when starting outside of virt-manager? Command line is (slightly reformatted for readability): /usr/bin/kvm -S -M pc-0.12 -enable-kvm -m 512 -smp 1 -name BORON \ -uuid fa7e5fbd-7d8e-43c4-ebd9-1504a4383eb1 \ -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/BORON.monitor,server,nowait \ -monitor chardev:monitor -localtime -boot c \ -drive file=/dev/FS1/BORON,if=ide,index=0,boot=on,format=raw \ -net nic,macaddr=52:54:00:20:0b:fd,vlan=0,name=nic.0 \ -net tap,fd=41,vlan=0,name=tap.0 -chardev pty,id=serial0 -serial chardev:serial0 \ -parallel none -usb -usbdevice tablet -vnc 127.0.0.1:1 -k en-us -vga cirrus

    Read the article

  • Why just splitting an Ethernet cable does not work?

    - by Sin Jeong-hun
    I thought the Ethernet is logically one-line communication bus (for argument's sake, I am excluding hubs). All machines attached in the bus hears the same signals and the machines themselves try to avoid collisions by randomly backing off. http://computer.howstuffworks.com/ethernet6.htm If so, why splitting one Ethernet line from my home router into two and connecting two computers would not work? Why do I have to add a switch to it? *What the Internet said would not work. [4 port home router] ------[one Ethernet cable]-----[simple splitter]======[two computers] *What the Internet said I should do [4 port home router] ------[one Ethernet cable]-----[switch]======[two computers] Is this because of the signal degradation (reduced electric current)? Thank you for all the answers! The reason why I did not just use the two ports of my home router is... The 4-port gigabit router is in my room and I had put a computer in another room (also my room, though). Since wired network is far more reliable and secure, I had bought a long Ethernet cable and and connected the computer to the router. Now I was thinking about adding another computer to that room. I could buy another long Ethernet cable, but then there will be two cables between the rooms. The one line already is a minor annoyance, so I thought if I could share the one line between the two computers in that room. A switch would work, but it requires power and is a little bit pricey. That is why I wondered why it would not work to simply split the physical Ethernet cable. Apparently I do not completely understand how Ethernet and a switch work. I just have some bit of knowledge I heard in my college class.

    Read the article

  • java warnings on linux

    - by Geo Papas
    Hello i am getting warnings after i have installed java on kubuntu 11.10. The java programs run but i always get 4 warnings: $ java Warning: no leading - on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: missing VM type on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: no leading - on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' Warning: missing VM type on line 1 of `/usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg' What am i missing? Thanks in advance! Here is the file content /usr/lib/jvm/java-6-sun-1.6.0.26/jre/lib/amd64/jvm.cfg : /usr/lib/jvm/java-6-sun # # %W% %E% # # Copyright (c) 2006, Oracle and/or its affiliates. All rights reserved. # ORACLE PROPRIETARY/CONFIDENTIAL. Use is subject to license terms. # # List of JVMs that can be used as an option to java, javac, etc. # Order is important -- first in this list is the default JVM. # NOTE that this both this file and its format are UNSUPPORTED and # WILL GO AWAY in a future release. # # You may also select a JVM in an arbitrary location with the # "-XXaltjvm=<jvm_dir>" option, but that too is unsupported # and may not be available in a future release. # -server KNOWN -client IGNORE -hotspot ERROR -classic WARN -native ERROR -green ERROR

    Read the article

  • cisco asa + action drop issue

    - by ghp
    Have created a tunnel between 10.x.y.z network and 122.a.b.c ..the tunnel is up and active, but when I try the packet tracer output ..I get the ACTION as drop. I have also enabled same-security-traffic permit intra-interface. Can someone help me what does this drop mean? Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule Packet Tracer output @Shane Madden: please find below the packet tracer output. CASA5K-A# CASA5K-A# config t CASA5K-A(config)# packet-tracer input inside tcp 10.x.y.112 0 122.a.b.c 0 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: Result: DROP Config: Implicit Rule Additional Information: Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule CASA5K-A(config)# ======================================================================== The access-group are as follows : access-group acl-inbound in interface outside access-group acl-outbound in interface inside and the access-list's are access-list acl-inbound extended permit tcp any any gt 1023 access-list acl-outbound extended permit ip object-group net-Source object net-dest

    Read the article

  • ASP.NET MVC 3: Razor’s @: and <text> syntax

    - by ScottGu
    This is another in a series of posts I’m doing that cover some of the new ASP.NET MVC 3 features: New @model keyword in Razor (Oct 19th) Layouts with Razor (Oct 22nd) Server-Side Comments with Razor (Nov 12th) Razor’s @: and <text> syntax (today) In today’s post I’m going to discuss two useful syntactical features of the new Razor view-engine – the @: and <text> syntax support. Fluid Coding with Razor ASP.NET MVC 3 ships with a new view-engine option called “Razor” (in addition to the existing .aspx view engine).  You can learn more about Razor, why we are introducing it, and the syntax it supports from my Introducing Razor blog post.  Razor minimizes the number of characters and keystrokes required when writing a view template, and enables a fast, fluid coding workflow. Unlike most template syntaxes, you do not need to interrupt your coding to explicitly denote the start and end of server blocks within your HTML. The Razor parser is smart enough to infer this from your code. This enables a compact and expressive syntax which is clean, fast and fun to type. For example, the Razor snippet below can be used to iterate a list of products: When run, it generates output like:   One of the techniques that Razor uses to implicitly identify when a code block ends is to look for tag/element content to denote the beginning of a content region.  For example, in the code snippet above Razor automatically treated the inner <li></li> block within our foreach loop as an HTML content block because it saw the opening <li> tag sequence and knew that it couldn’t be valid C#.  This particular technique – using tags to identify content blocks within code – is one of the key ingredients that makes Razor so clean and productive with scenarios involving HTML creation. Using @: to explicitly indicate the start of content Not all content container blocks start with a tag element tag, though, and there are scenarios where the Razor parser can’t implicitly detect a content block. Razor addresses this by enabling you to explicitly indicate the beginning of a line of content by using the @: character sequence within a code block.  The @: sequence indicates that the line of content that follows should be treated as a content block: As a more practical example, the below snippet demonstrates how we could output a “(Out of Stock!)” message next to our product name if the product is out of stock: Because I am not wrapping the (Out of Stock!) message in an HTML tag element, Razor can’t implicitly determine that the content within the @if block is the start of a content block.  We are using the @: character sequence to explicitly indicate that this line within our code block should be treated as content. Using Code Nuggets within @: content blocks In addition to outputting static content, you can also have code nuggets embedded within a content block that is initiated using a @: character sequence.  For example, we have two @: sequences in the code snippet below: Notice how within the second @: sequence we are emitting the number of units left within the content block (e.g. - “(Only 3 left!”). We are doing this by embedding a @p.UnitsInStock code nugget within the line of content. Multiple Lines of Content Razor makes it easy to have multiple lines of content wrapped in an HTML element.  For example, below the inner content of our @if container is wrapped in an HTML <p> element – which will cause Razor to treat it as content: For scenarios where the multiple lines of content are not wrapped by an outer HTML element, you can use multiple @: sequences: Alternatively, Razor also allows you to use a <text> element to explicitly identify content: The <text> tag is an element that is treated specially by Razor. It causes Razor to interpret the inner contents of the <text> block as content, and to not render the containing <text> tag element (meaning only the inner contents of the <text> element will be rendered – the tag itself will not).  This makes it convenient when you want to render multi-line content blocks that are not wrapped by an HTML element.  The <text> element can also optionally be used to denote single-lines of content, if you prefer it to the more concise @: sequence: The above code will render the same output as the @: version we looked at earlier.  Razor will automatically omit the <text> wrapping element from the output and just render the content within it.  Summary Razor enables a clean and concise templating syntax that enables a very fluid coding workflow.  Razor’s smart detection of <tag> elements to identify the beginning of content regions is one of the reasons that the Razor approach works so well with HTML generation scenarios, and it enables you to avoid having to explicitly mark the beginning/ending of content regions in about 95% of if/else and foreach scenarios. Razor’s @: and <text> syntax can then be used for scenarios where you want to avoid using an HTML element within a code container block, and need to more explicitly denote a content region. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

    Read the article

  • Error when trying to compile abgx360: C++ compiler cannot create executables

    - by era878
    I am trying to compile the abgx360 GUI. First I run home/eric/Desktop/abgx360-1.0.5/configure but I recieve this error: checking for C++ compiler default output file name... configure: error: C++ compiler cannot create executables See `config.log' for more details. Then i run make but I recieve this error: make: * No rule to make target `/home/eric/Desktop/abgx360-1.0.5/Makefile.am', needed by `/home/eric/Desktop/abgx360-1.0.5/Makefile.in'. Stop. Here is my 'config.log': This file contains any messages produced by compilers while running configure, to aid debugging if configure makes a mistake. It was created by abgx360gui configure 1.0.2, which was generated by GNU Autoconf 2.61. Invocation command line was $ /home/eric/Desktop/abgx360gui-1.0.2/configure ## --------- ## ## Platform. ## ## --------- ## hostname = Eric-Desktop uname -m = x86_64 uname -r = 2.6.35-27-generic uname -s = Linux uname -v = #48-Ubuntu SMP Tue Feb 22 20:25:46 UTC 2011 /usr/bin/uname -p = unknown /bin/uname -X = unknown /bin/arch = unknown /usr/bin/arch -k = unknown /usr/convex/getsysinfo = unknown /usr/bin/hostinfo = unknown /bin/machine = unknown /usr/bin/oslevel = unknown /bin/universe = unknown PATH: /usr/local/sbin PATH: /usr/local/bin PATH: /usr/sbin PATH: /usr/bin PATH: /sbin PATH: /bin PATH: /usr/games ## ----------- ## ## Core tests. ## ## ----------- ## configure:1800: checking for a BSD-compatible install configure:1856: result: /usr/bin/install -c configure:1867: checking whether build environment is sane configure:1910: result: yes configure:1938: checking for a thread-safe mkdir -p configure:1977: result: /bin/mkdir -p configure:1990: checking for gawk configure:2020: result: no configure:1990: checking for mawk configure:2006: found /usr/bin/mawk configure:2017: result: mawk configure:2028: checking whether make sets $(MAKE) configure:2049: result: yes configure:2302: checking for g++ configure:2332: result: no configure:2302: checking for c++ configure:2332: result: no configure:2302: checking for gpp configure:2332: result: no configure:2302: checking for aCC configure:2332: result: no configure:2302: checking for CC configure:2332: result: no configure:2302: checking for cxx configure:2332: result: no configure:2302: checking for cc++ configure:2332: result: no configure:2302: checking for cl.exe configure:2332: result: no configure:2302: checking for FCC configure:2332: result: no configure:2302: checking for KCC configure:2332: result: no configure:2302: checking for RCC configure:2332: result: no configure:2302: checking for xlC_r configure:2332: result: no configure:2302: checking for xlC configure:2332: result: no configure:2360: checking for C++ compiler version configure:2367: g++ --version >&5 /home/eric/Desktop/abgx360gui-1.0.2/configure: line 2368: g++: command not found configure:2370: $? = 127 configure:2377: g++ -v >&5 /home/eric/Desktop/abgx360gui-1.0.2/configure: line 2378: g++: command not found configure:2380: $? = 127 configure:2387: g++ -V >&5 /home/eric/Desktop/abgx360gui-1.0.2/configure: line 2388: g++: command not found configure:2390: $? = 127 configure:2413: checking for C++ compiler default output file name configure:2440: g++ conftest.cpp >&5 /home/eric/Desktop/abgx360gui-1.0.2/configure: line 2441: g++: command not found configure:2443: $? = 127 configure:2481: result: configure: failed program was: | /* confdefs.h. */ | #define PACKAGE_NAME "abgx360gui" | #define PACKAGE_TARNAME "abgx360gui" | #define PACKAGE_VERSION "1.0.2" | #define PACKAGE_STRING "abgx360gui 1.0.2" | #define PACKAGE_BUGREPORT "" | #define PACKAGE "abgx360gui" | #define VERSION "1.0.2" | /* end confdefs.h. */ | | int | main () | { | | ; | return 0; | } configure:2488: error: C++ compiler cannot create executables See `config.log' for more details. ## ---------------- ## ## Cache variables. ## ## ---------------- ## ac_cv_env_CCC_set= ac_cv_env_CCC_value= ac_cv_env_CC_set= ac_cv_env_CC_value= ac_cv_env_CFLAGS_set= ac_cv_env_CFLAGS_value= ac_cv_env_CPPFLAGS_set= ac_cv_env_CPPFLAGS_value= ac_cv_env_CPP_set= ac_cv_env_CPP_value= ac_cv_env_CXXFLAGS_set= ac_cv_env_CXXFLAGS_value= ac_cv_env_CXX_set= ac_cv_env_CXX_value= ac_cv_env_LDFLAGS_set= ac_cv_env_LDFLAGS_value= ac_cv_env_LIBS_set= ac_cv_env_LIBS_value= ac_cv_env_build_alias_set= ac_cv_env_build_alias_value= ac_cv_env_host_alias_set= ac_cv_env_host_alias_value= ac_cv_env_target_alias_set= ac_cv_env_target_alias_value= ac_cv_path_install='/usr/bin/install -c' ac_cv_path_mkdir=/bin/mkdir ac_cv_prog_AWK=mawk ac_cv_prog_make_make_set=yes ## ----------------- ## ## Output variables. ## ## ----------------- ## ACLOCAL='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run aclocal-1.10' AMDEPBACKSLASH='' AMDEP_FALSE='' AMDEP_TRUE='' AMTAR='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run tar' AUTOCONF='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run autoconf' AUTOHEADER='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run autoheader' AUTOMAKE='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run automake-1.10' AWK='mawk' CC='' CCDEPMODE='' CFLAGS='' CPP='' CPPFLAGS='' CXX='g++' CXXDEPMODE='' CXXFLAGS='' CYGPATH_W='echo' DEFS='' DEPDIR='' ECHO_C='' ECHO_N='-n' ECHO_T='' EGREP='' EXEEXT='' GREP='' INSTALL_DATA='${INSTALL} -m 644' INSTALL_PROGRAM='${INSTALL}' INSTALL_SCRIPT='${INSTALL}' INSTALL_STRIP_PROGRAM='$(install_sh) -c -s' LDFLAGS='' LIBOBJS='' LIBS='' LTLIBOBJS='' MAKEINFO='${SHELL} /home/eric/Desktop/abgx360gui-1.0.2/missing --run makeinfo' OBJEXT='' PACKAGE='abgx360gui' PACKAGE_BUGREPORT='' PACKAGE_NAME='abgx360gui' PACKAGE_STRING='abgx360gui 1.0.2' PACKAGE_TARNAME='abgx360gui' PACKAGE_VERSION='1.0.2' PATH_SEPARATOR=':' SET_MAKE='' SHELL='/bin/bash' STRIP='' VERSION='1.0.2' WX_CFLAGS='' WX_CFLAGS_ONLY='' WX_CONFIG_PATH='' WX_CPPFLAGS='' WX_CXXFLAGS='' WX_CXXFLAGS_ONLY='' WX_LIBS='' WX_LIBS_STATIC='' WX_RESCOMP='' WX_VERSION='' ac_ct_CC='' ac_ct_CXX='' am__fastdepCC_FALSE='' am__fastdepCC_TRUE='' am__fastdepCXX_FALSE='' am__fastdepCXX_TRUE='' am__include='' am__isrc=' -I$(srcdir)' am__leading_dot='.' am__quote='' am__tar='${AMTAR} chof - "$$tardir"' am__untar='${AMTAR} xf -' bindir='${exec_prefix}/bin' build_alias='' datadir='${datarootdir}' datarootdir='${prefix}/share' docdir='${datarootdir}/doc/${PACKAGE_TARNAME}' dvidir='${docdir}' exec_prefix='NONE' host_alias='' htmldir='${docdir}' includedir='${prefix}/include' infodir='${datarootdir}/info' install_sh='$(SHELL) /home/eric/Desktop/abgx360gui-1.0.2/install-sh' libdir='${exec_prefix}/lib' libexecdir='${exec_prefix}/libexec' localedir='${datarootdir}/locale' localstatedir='${prefix}/var' mandir='${datarootdir}/man' mkdir_p='/bin/mkdir -p' oldincludedir='/usr/include' pdfdir='${docdir}' prefix='NONE' program_transform_name='s,x,x,' psdir='${docdir}' sbindir='${exec_prefix}/sbin' sharedstatedir='${prefix}/com' sysconfdir='${prefix}/etc' target_alias='' ## ----------- ## ## confdefs.h. ## ## ----------- ## #define PACKAGE_NAME "abgx360gui" #define PACKAGE_TARNAME "abgx360gui" #define PACKAGE_VERSION "1.0.2" #define PACKAGE_STRING "abgx360gui 1.0.2" #define PACKAGE_BUGREPORT "" #define PACKAGE "abgx360gui" #define VERSION "1.0.2" configure: exit 77

    Read the article

  • How to get sound on macbook pro 4,1

    - by Thomas
    I have just installed Xubuntu 12.04.2. My soundcard is detected: thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 Everything is put to max in alsamixer and nothing is muted (all the sliders are on OO. My speakers do not work, but when I plug in a headphone I hear it very soft. When I connect my stereo and put the sound VERY loud (3-blocks-of-complaining-neighbours loud) I hear it on a normal level but crackling. I added options snd-hda-intel model=mbp5 amixer set IEC958 off to at the end of /etc/modprobe.d/alsa-base.conf. When it's still not working I tried everything here: https://help.ubuntu.com/community/SoundTroubleshooting 1 >>> list-sinks 1 sink(s) available. * index: 0 name: <alsa_output.pci-0000_00_1b.0.analog-stereo> driver: <module-alsa-card.c> flags: HARDWARE HW_MUTE_CTRL HW_VOLUME_CTRL DECIBEL_VOLUME LATENCY DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE priority: 9959 volume: 0: 100% 1: 100% 0: 0.00 dB 1: 0.00 dB balance 0.00 base volume: 100% 0.00 dB volume steps: 65537 muted: no current latency: 0.00 ms max request: 0 KiB max rewind: 0 KiB monitor source: 0 sample spec: s16le 2ch 44100Hz channel map: front-left,front-right Stereo used by: 0 linked by: 0 configured latency: 0.00 ms; range is 0.50 .. 371.52 ms card: 0 <alsa_card.pci-0000_00_1b.0> module: 4 properties: alsa.resolution_bits = "16" device.api = "alsa" device.class = "sound" alsa.class = "generic" alsa.subclass = "generic-mix" alsa.name = "ALC889A Analog" alsa.id = "ALC889A Analog" alsa.subdevice = "0" alsa.subdevice_name = "subdevice #0" alsa.device = "0" alsa.card = "0" alsa.card_name = "HDA Intel" alsa.long_card_name = "HDA Intel at 0x9b500000 irq 46" alsa.driver_name = "snd_hda_intel" device.bus_path = "pci-0000:00:1b.0" sysfs.path = "/devices/pci0000:00/0000:00:1b.0/sound/card0" device.bus = "pci" device.vendor.id = "8086" device.vendor.name = "Intel Corporation" device.product.name = "82801H (ICH8 Family) HD Audio Controller" device.form_factor = "internal" device.string = "front:0" device.buffering.buffer_size = "65536" device.buffering.fragment_size = "32768" device.access_mode = "mmap+timer" device.profile.name = "analog-stereo" device.profile.description = "Analog Stereo" device.description = "Built-in Audio Analog Stereo" alsa.mixer_name = "Realtek ALC889A" alsa.components = "HDA:10ec0885,106b3a00,00100103" module-udev-detect.discovered = "1" device.icon_name = "audio-card-pci" ports: analog-output-speaker: Speakers (priority 10000, available: unknown) properties: analog-output-headphones: Headphones (priority 9000, available: no) properties: active port: <analog-output-speaker> 2 and 3: Doesn't seem an permission issue, the sound is very far away (See opening paragraph). 4 thomas@thomas-pc:~$ sudo aplay -l **** List of PLAYBACK Hardware Devices **** Home directory /home/thomas not ours. card 0: Intel [HDA Intel], device 0: ALC889A Analog [ALC889A Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: Intel [HDA Intel], device 1: ALC889A Digital [ALC889A Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 5 thomas@thomas-pc:~$ find /lib/modules/`uname -r` | grep snd /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-hwdep.ko /lib/modules/3.2.0-48-generic/kernel/sound/core/snd-pcm.ko [.. huge lists continues ..] /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/pdaudiocf/snd-pdaudiocf.ko /lib/modules/3.2.0-48-generic/kernel/sound/pcmcia/vx/snd-vxpocket.ko thomas@thomas-pc:~$ 6 thomas@thomas-pc:~$ lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 03) Subsystem: Apple Inc. Device 00a4 Flags: bus master, fast devsel, latency 0, IRQ 46 Memory at 9b500000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 7 I guess it's supported. Linux mint and Xubuntu 13.04 had no trouble with sounds. Everything worked out of the box Thanks in advance Edit: alsa-info.sh output: WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' ALSA Information Script v 0.4.62 -------------------------------- This script visits the following commands/files to collect diagnostic information about your ALSA installation and sound related hardware. dmesg lspci lsmod aplay amixer alsactl /proc/asound/ /sys/class/sound/ ~/.asoundrc (etc.) See './alsa-info.sh --help' for command line options. WARNING: /etc/modprobe.d/alsa-base.conf line 45: ignoring bad line starting with 'amixer' Automatically upload ALSA information to www.alsa-project.org? [y/N] : y Uploading information to www.alsa-project.org ... Done! Your ALSA information is located at http://www.alsa-project.org/db/?f=6cffc584284d4c0b266eb53249824ef83d6c4e3e Please inform the person helping you. thomas@thomas-pc:~$

    Read the article

  • Grub 'Read Error' - Only Loads with LiveCD

    - by Ryan Sharp
    Problem After installing Ubuntu to complete my Windows 7/Ubuntu 12.04 dual-boot setup, Grub just wouldn't load at all unless I boot from the LiveCD. Afterwards, everything works completely normal. However, this workaround isn't a solution and I'd like to be able to boot without the aid of a disc. Fdisk -l Using the fdisk -l command, I am given the following: Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x324971d1 Device Boot Start End Blocks Id System /dev/sda1 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 208896 48957439 24374272 7 HPFS/NTFS/exFAT /dev/sda3 * 48959486 124067839 37554177 5 Extended /dev/sda5 48959488 124067839 37554176 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xc0ee6a69 Device Boot Start End Blocks Id System /dev/sdb1 1024208894 1953523711 464657409 5 Extended /dev/sdb3 * 2048 1024206847 512102400 7 HPFS/NTFS/exFAT /dev/sdb5 1024208896 1937897471 456844288 83 Linux /dev/sdb6 1937899520 1953523711 7812096 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x292eee23 Device Boot Start End Blocks Id System /dev/sdc1 2048 625141759 312569856 7 HPFS/NTFS/exFAT Bootinfoscript I've used the BootInfoScript, and received the following output: Boot Info Script 0.61 [1 April 2012] ============================= Boot Info Summary: =============================== => Grub2 (v1.99) is installed in the MBR of /dev/sda and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Grub2 (v1.99) is installed in the MBR of /dev/sdb and looks at sector 1 of the same hard drive for core.img. core.img is at this location and looks for (,msdos5)/boot/grub on this drive. => Windows is installed in the MBR of /dev/sdc. sda1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: /bootmgr /Boot/BCD sda2: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Windows 7 Boot files: /bootmgr /Boot/BCD /Windows/System32/winload.exe sda3: __________________________________________________________________________ File system: Extended Partition Boot sector type: Unknown Boot sector info: sda5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Ubuntu 12.04.1 LTS Boot files: /boot/grub/grub.cfg /etc/fstab /boot/grub/core.img sdb1: __________________________________________________________________________ File system: Extended Partition Boot sector type: - Boot sector info: sdb5: __________________________________________________________________________ File system: ext4 Boot sector type: - Boot sector info: Operating System: Boot files: sdb6: __________________________________________________________________________ File system: swap Boot sector type: - Boot sector info: sdb3: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: According to the info in the boot sector, sdb3 starts at sector 200744960. But according to the info from fdisk, sdb3 starts at sector 2048. According to the info in the boot sector, sdb3 has 823461887 sectors, but according to the info from fdisk, it has 1024204799 sectors. Operating System: Boot files: sdc1: __________________________________________________________________________ File system: ntfs Boot sector type: Windows Vista/7: NTFS Boot sector info: No errors found in the Boot Parameter Block. Operating System: Boot files: ============================ Drive/Partition Info: ============================= Drive: sda _____________________________________________________________________ Disk /dev/sda: 64.0 GB, 64023257088 bytes 255 heads, 63 sectors/track, 7783 cylinders, total 125045424 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sda1 2,048 206,847 204,800 7 NTFS / exFAT / HPFS /dev/sda2 208,896 48,957,439 48,748,544 7 NTFS / exFAT / HPFS /dev/sda3 * 48,959,486 124,067,839 75,108,354 5 Extended /dev/sda5 48,959,488 124,067,839 75,108,352 83 Linux Drive: sdb _____________________________________________________________________ Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdb1 1,024,208,894 1,953,523,711 929,314,818 5 Extended /dev/sdb5 1,024,208,896 1,937,897,471 913,688,576 83 Linux /dev/sdb6 1,937,899,520 1,953,523,711 15,624,192 82 Linux swap / Solaris /dev/sdb3 * 2,048 1,024,206,847 1,024,204,800 7 NTFS / exFAT / HPFS Drive: sdc _____________________________________________________________________ Disk /dev/sdc: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes Partition Boot Start Sector End Sector # of Sectors Id System /dev/sdc1 2,048 625,141,759 625,139,712 7 NTFS / exFAT / HPFS "blkid" output: ________________________________________________________________ Device UUID TYPE LABEL /dev/sda1 A48056DF8056B80E ntfs System Reserved /dev/sda2 A8C6D6A4C6D671D4 ntfs Windows /dev/sda5 fd71c537-3715-44e1-b1fe-07537e22b3dd ext4 /dev/sdb3 6373D03D0A3747A8 ntfs Steam /dev/sdb5 6f5a6eb3-a932-45aa-893e-045b57708270 ext4 /dev/sdb6 469848c8-867a-41b7-b0e1-b813a43c64af swap /dev/sdc1 725D7B961CF34B1B ntfs backup ================================ Mount points: ================================= Device Mount_Point Type Options /dev/sda5 / ext4 (rw,noatime,nodiratime,discard,errors=remount-ro) /dev/sdb5 /home ext4 (rw) =========================== sda5/boot/grub/grub.cfg: =========================== -------------------------------------------------------------------------------- # # DO NOT EDIT THIS FILE # # It is automatically generated by grub-mkconfig using templates # from /etc/grub.d and settings from /etc/default/grub # ### BEGIN /etc/grub.d/00_header ### if [ -s $prefix/grubenv ]; then set have_grubenv=true load_env fi set default="0" if [ "${prev_saved_entry}" ]; then set saved_entry="${prev_saved_entry}" save_env saved_entry set prev_saved_entry= save_env prev_saved_entry set boot_once=true fi function savedefault { if [ -z "${boot_once}" ]; then saved_entry="${chosen}" save_env saved_entry fi } function recordfail { set recordfail=1 if [ -n "${have_grubenv}" ]; then if [ -z "${boot_once}" ]; then save_env recordfail; fi; fi } function load_video { insmod vbe insmod vga insmod video_bochs insmod video_cirrus } insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd if loadfont /usr/share/grub/unicode.pf2 ; then set gfxmode=auto load_video insmod gfxterm insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd set locale_dir=($root)/boot/grub/locale set lang=en_GB insmod gettext fi terminal_output gfxterm if [ "${recordfail}" = 1 ]; then set timeout=-1 else set timeout=10 fi ### END /etc/grub.d/00_header ### ### BEGIN /etc/grub.d/05_debian_theme ### set menu_color_normal=white/black set menu_color_highlight=black/light-gray if background_color 44,0,30; then clear fi ### END /etc/grub.d/05_debian_theme ### ### BEGIN /etc/grub.d/10_linux ### function gfxmode { set gfxpayload="${1}" if [ "${1}" = "keep" ]; then set vt_handoff=vt.handoff=7 else set vt_handoff= fi } if [ "${recordfail}" != 1 ]; then if [ -e ${prefix}/gfxblacklist.txt ]; then if hwmatch ${prefix}/gfxblacklist.txt 3; then if [ ${match} = 0 ]; then set linux_gfx_mode=keep else set linux_gfx_mode=text fi else set linux_gfx_mode=text fi else set linux_gfx_mode=keep fi else set linux_gfx_mode=text fi export linux_gfx_mode if [ "${linux_gfx_mode}" != "text" ]; then load_video; fi menuentry 'Ubuntu, with Linux 3.2.0-29-generic' --class ubuntu --class gnu-linux --class gnu --class os { recordfail gfxmode $linux_gfx_mode insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro quiet splash $vt_handoff initrd /boot/initrd.img-3.2.0-29-generic } menuentry 'Ubuntu, with Linux 3.2.0-29-generic (recovery mode)' --class ubuntu --class gnu-linux --class gnu --class os { recordfail insmod gzio insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd echo 'Loading Linux 3.2.0-29-generic ...' linux /boot/vmlinuz-3.2.0-29-generic root=UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd ro recovery nomodeset echo 'Loading initial ramdisk ...' initrd /boot/initrd.img-3.2.0-29-generic } ### END /etc/grub.d/10_linux ### ### BEGIN /etc/grub.d/20_linux_xen ### ### END /etc/grub.d/20_linux_xen ### ### BEGIN /etc/grub.d/20_memtest86+ ### menuentry "Memory test (memtest86+)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin } menuentry "Memory test (memtest86+, serial console 115200)" { insmod part_msdos insmod ext2 set root='(hd0,msdos5)' search --no-floppy --fs-uuid --set=root fd71c537-3715-44e1-b1fe-07537e22b3dd linux16 /boot/memtest86+.bin console=ttyS0,115200n8 } ### END /etc/grub.d/20_memtest86+ ### ### BEGIN /etc/grub.d/30_os-prober ### menuentry "Windows 7 (loader) (on /dev/sda1)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos1)' search --no-floppy --fs-uuid --set=root A48056DF8056B80E chainloader +1 } menuentry "Windows 7 (loader) (on /dev/sda2)" --class windows --class os { insmod part_msdos insmod ntfs set root='(hd0,msdos2)' search --no-floppy --fs-uuid --set=root A8C6D6A4C6D671D4 chainloader +1 } ### END /etc/grub.d/30_os-prober ### ### BEGIN /etc/grub.d/40_custom ### # This file provides an easy way to add custom menu entries. Simply type the # menu entries you want to add after this comment. Be careful not to change # the 'exec tail' line above. ### END /etc/grub.d/40_custom ### ### BEGIN /etc/grub.d/41_custom ### if [ -f $prefix/custom.cfg ]; then source $prefix/custom.cfg; fi ### END /etc/grub.d/41_custom ### -------------------------------------------------------------------------------- =============================== sda5/etc/fstab: ================================ -------------------------------------------------------------------------------- # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # / was on /dev/sda5 during installation UUID=fd71c537-3715-44e1-b1fe-07537e22b3dd / ext4 noatime,nodiratime,discard,errors=remount-ro 0 1 # /home was on /dev/sdb5 during installation UUID=6f5a6eb3-a932-45aa-893e-045b57708270 /home ext4 defaults 0 2 # swap was on /dev/sdb6 during installation UUID=469848c8-867a-41b7-b0e1-b813a43c64af none swap sw 0 0 tmpfs /tmp tmpfs defaults,noatime,mode=1777 0 0 -------------------------------------------------------------------------------- =================== sda5: Location of files loaded by Grub: ==================== GiB - GB File Fragment(s) = boot/grub/core.img 1 = boot/grub/grub.cfg 1 = boot/initrd.img-3.2.0-29-generic 2 = boot/vmlinuz-3.2.0-29-generic 1 = initrd.img 2 = vmlinuz 1 ======================== Unknown MBRs/Boot Sectors/etc: ======================== Unknown BootLoader on sda3 00000000 63 6f 70 69 61 20 65 20 63 6f 6c 61 41 63 65 64 |copia e colaAced| 00000010 65 72 20 61 20 74 6f 64 6f 20 6f 20 74 65 78 74 |er a todo o text| 00000020 6f 20 66 61 6c 61 64 6f 20 75 74 69 6c 69 7a 61 |o falado utiliza| 00000030 6e 64 6f 20 61 20 63 6f 6e 76 65 72 73 c3 a3 6f |ndo a convers..o| 00000040 20 64 65 20 74 65 78 74 6f 20 70 61 72 61 20 76 | de texto para v| 00000050 6f 7a 4d 61 6e 69 70 75 6c 61 72 20 61 73 20 64 |ozManipular as d| 00000060 65 66 69 6e 69 c3 a7 c3 b5 65 73 20 71 75 65 20 |efini....es que | 00000070 63 6f 6e 74 72 6f 6c 61 6d 20 6f 20 61 63 65 73 |controlam o aces| 00000080 73 6f 20 64 65 20 57 65 62 73 69 74 65 73 20 61 |so de Websites a| 00000090 20 63 6f 6f 6b 69 65 73 2c 20 4a 61 76 61 53 63 | cookies, JavaSc| 000000a0 72 69 70 74 20 65 20 70 6c 75 67 2d 69 6e 73 4d |ript e plug-insM| 000000b0 61 6e 69 70 75 6c 61 72 20 61 73 20 64 65 66 69 |anipular as defi| 000000c0 6e 69 c3 a7 c3 b5 65 73 20 72 65 6c 61 63 69 6f |ni....es relacio| 000000d0 6e 61 64 61 73 20 63 6f 6d 20 70 72 69 76 61 63 |nadas com privac| 000000e0 69 64 61 64 65 41 63 65 64 65 72 20 61 6f 73 20 |idadeAceder aos | 000000f0 73 65 75 73 20 70 65 72 69 66 c3 a9 72 69 63 6f |seus perif..rico| 00000100 73 20 55 53 42 55 74 69 6c 69 7a 61 72 20 6f 20 |s USBUtilizar o | 00000110 73 65 75 20 6d 69 63 72 6f 66 6f 6e 65 55 74 69 |seu microfoneUti| 00000120 6c 69 7a 61 72 20 61 20 73 75 61 20 63 c3 a2 6d |lizar a sua c..m| 00000130 61 72 61 55 74 69 6c 69 7a 61 72 20 6f 20 73 65 |araUtilizar o se| 00000140 75 20 6d 69 63 72 6f 66 6f 6e 65 20 65 20 61 20 |u microfone e a | 00000150 63 c3 a2 6d 61 72 61 4e c3 a3 6f 20 66 6f 69 20 |c..maraN..o foi | 00000160 70 6f 73 73 c3 ad 76 65 6c 20 65 6e 63 6f 6e 74 |poss..vel encont| 00000170 72 61 72 20 6f 20 63 61 6d 69 6e 68 6f 20 61 62 |rar o caminho ab| 00000180 73 6f 6c 75 74 6f 20 70 61 72 61 20 6f 20 64 69 |soluto para o di| 00000190 72 65 63 74 c3 b3 72 69 6f 20 61 20 65 6d 70 61 |rect..rio a empa| 000001a0 63 6f 74 61 72 2e 4f 20 64 69 72 65 63 74 c3 b3 |cotar.O direct..| 000001b0 72 69 6f 20 64 65 20 65 6e 74 72 61 64 61 00 fe |rio de entrada..| 000001c0 ff ff 83 fe ff ff 02 00 00 00 00 10 7a 04 00 00 |............z...| 000001d0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 000001f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 55 aa |..............U.| 00000200 =============================== StdErr Messages: =============================== xz: (stdin): Compressed data is corrupt xz: (stdin): Compressed data is corrupt awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in awk: cmd. line:36: Math support is not compiled in Begging / Appreciation ;) If anything else is required to solve my problem, please ask. My only hopes are that I can solve this, and that doing so won't require re-installation of Grub due to how complicated the procedures are, or that I would be needed to reinstall the OS', as I have done so about six times already since friday due to several other issues I've encountered. Thank you, and good day. System Ubuntu 12.04 64-bit / Windows 7 SP1 64-bit 64GB SSD as boot/OS drive, 1TB HDD as /Home Swap and Steam drive.

    Read the article

  • Visual Studio Little Wonders: Box Selection

    - by James Michael Hare
    So this week I decided I’d do a Little Wonder of a different kind and focus on an underused IDE improvement: Visual Studio’s Box Selection capability. This is a handy feature that many people still don’t realize was made available in Visual Studio 2010 (and beyond).  True, there have been other editors in the past with this capability, but now that it’s fully part of Visual Studio we can enjoy it’s goodness from within our own IDE. So, for those of you who don’t know what box selection is and what it allows you to do, read on! Sometimes, we want to select beyond the horizontal… The problem with traditional text selection in many editors is that it is horizontally oriented.  Sure, you can select multiple rows, but if you do you will pull in the entire row (at least for the middle rows).  Under the old selection scheme, if you wanted to select a portion of text from each row (a “box” of text) you were out of luck.  Box selection rectifies this by allowing you to select a box of text that bounded by a selection rectangle that you can grow horizontally or vertically.  So let’s think a situation that could occur where this comes in handy. Let’s say, for instance, that we are defining an enum in our code that we want to be able to translate into some string values (possibly to be stored in a database, output to screen, etc.). Perhaps such an enum would look like this: 1: public enum OrderType 2: { 3: Buy, // buy shares of a commodity 4: Sell, // sell shares of a commodity 5: Exchange, // exchange one commodity for another 6: Cancel, // cancel an order for a commodity 7: } 8:  Now, let’s say we are in the process of creating a Dictionary<K,V> to translate our OrderType: 1: var translator = new Dictionary<OrderType, string> 2: { 3: // do I really want to retype all this??? 4: }; Yes the example above is contrived so that we will pull some garbage if we do a multi-line select. I could select the lines above using the traditional multi-line selection: And then paste them into the translator code, which would result in this: 1: var translator = new Dictionary<OrderType, string> 2: { 3: Buy, // buy shares of a commodity 4: Sell, // sell shares of a commodity 5: Exchange, // exchange one commodity for another 6: Cancel, // cancel an order for a commodity 7: }; But I have a lot of junk there, sure I can manually clear it out, or use some search and replace magic, but if this were hundreds of lines instead of just a few that would quickly become cumbersome. The Box Selection Now that we have the ability to create box selections, we can select the box of text to delete!  Most of us are familiar with the fact we can drag the mouse (or hold [Shift] and use the arrow keys) to create a selection that can span multiple rows: Box selection, however, actually allows us to select a box instead of the typical horizontal lines: Then we can press the [delete] key and the pesky comments are all gone! You can do this either by holding down [Alt] while you select with your mouse, or by holding down [Alt+Shift] and using the arrow keys on the keyboard to grow the box horizontally or vertically. So now we have: 1: var translator = new Dictionary<OrderType, string> 2: { 3: Buy, 4: Sell, 5: Exchange, 6: Cancel, 7: }; Which is closer, but we still need an opening curly, the string to translate to, and the closing curly and comma. Fortunately, again, this is easy with box selections due to the fact box selection can even work for a zero-width selection! That is, hold down [Alt] and either drag down with no width, or hold down [Alt+Shift] and arrow down and you will define a selection range with no width, essentially, a vertical line selection: Notice the faint selection line on the right? So why is this useful? Well, just like with any selected range, we can type and it will replace the selection. What does this mean for box selections? It means that we can insert the same text all the way down on each line! If we have the same selection above, and type a curly and a space, we’d get: Imagine doing this over hundreds of lines and think of what a time saver it could be! Now make a zero-width selection on the other side: And type a curly and a comma, and we’d get: So close! Now finally, imagine we’ve already defined these strings somewhere and want to paste them in: 1: const private string BuyText = "Buy Shares"; 2: const private string SellText = "Sell Shares"; 3: const private string ExchangeText = "Exchange"; 4: const private string CancelText = "Cancel"; We can, again, use our box selection to pull out the constant names: And clicking copy (or [CTRL+C]) and then selecting a range to paste into: And finally clicking paste (or [CTRL+V]) to get the final result: 1: var translator = new Dictionary<OrderType, string> 2: { 3: { Buy, BuyText }, 4: { Sell, SellText }, 5: { Exchange, ExchangeText }, 6: { Cancel, CancelText }, 7: };   Sure, this was a contrived example, but I’m sure you’ll agree that it adds myriad possibilities of new ways to copy and paste vertical selections, as well as inserting text across a vertical slice. Summary: While box selection has been around in other editors, we finally get to experience it in VS2010 and beyond. It is extremely handy for selecting columns of information for cutting, copying, and pasting. In addition, it allows you to create a zero-width vertical insertion point that can be used to enter the same text across multiple rows. Imagine the time you can save adding repetitive code across multiple lines!  Try it, the more you use it, the more you’ll love it! Technorati Tags: C#,CSharp,.NET,Visual Studio,Little Wonders,Box Selection

    Read the article

  • Take Advantage of Oracle's Ongoing Assurance Effort!

    - by eric.maurice
    Hi, this is Eric Maurice again! A few years ago, I posted a blog entry, which discussed the psychology of patching. The point of this blog entry was that a natural tendency existed for systems and database administrators to be reluctant to apply patches, even security patches, because of the fear of "breaking" the system. Unfortunately, this belief in the principle "if it ain't broke, don't fix it!" creates significant risks for organizations. Running systems without applying the proper security patches can greatly compromise the security posture of the organization because the security controls available in the affected system may be compromised as a result of the existence of the unfixed vulnerabilities. As a result, Oracle continues to strongly recommend that customers apply all security fixes as soon as possible. Most recently, I have had a number of conversations with customers who questioned the need to upgrade their highly stable but otherwise unsupported Oracle systems. These customers wanted to know more about the kind of security risks they were exposed to, by running obsolete versions of Oracle software. As per Oracle Support Policies, Critical Patch Updates are produced for currently supported products. In other words, Critical Patch Updates are not created by Oracle for product versions that are no longer covered under the Premier Support or Extended Support phases of the Lifetime Support Policy. One statement used in each Critical Patch Update Advisory is particularly important: "We recommend that customers upgrade to a supported version of Oracle products in order to obtain patches. Unsupported products, releases and versions are not tested for the presence of vulnerabilities addressed by this Critical Patch Update. However, it is likely that earlier versions of affected releases are also affected by these vulnerabilities." The purpose of this warning is to inform Oracle customers that a number of the vulnerabilities fixed in each Critical Patch Update may affect older versions of a specific product line. In other words, each Critical Patch Update provides a number of fixes for currently supported versions of a given product line (this information is listed for each bug in the Risk Matrices of the Critical Patch Update Advisory), but the unsupported versions in the same product line, while they may be affected by the vulnerabilities, will not receive the fixes, and are therefore vulnerable to attacks. The risk assumed by organizations wishing to remain on unsupported versions is amplified by the behavior of malicious hackers, who typically will attempt to, and sometimes succeed in, reverse-engineering the content of vendors' security fixes. As a result, it is not uncommon for exploits to be published soon after Oracle discloses vulnerabilities with the release of a Critical Patch Update or Security Alert. Let's consider now the nature of the vulnerabilities that may exist in obsolete versions of Oracle software. A number of severe vulnerabilities have been fixed by Oracle over the years. While Oracle does not test unsupported products, releases and versions for the presence of vulnerabilities addressed by each Critical Patch Update, it should be assumed that a number of the vulnerabilities fixed with the Critical Patch Update program do exist in unsupported versions (regardless of the product considered). The most severe vulnerabilities fixed in past Critical Patch Updates may result in full compromise of the targeted systems, down to the OS level, by remote and unauthenticated users (these vulnerabilities receive a CVSS Base Score of 10.0) or almost as critically, may result in the compromise of the affected systems (without compromising the underlying OS) by a remote and unauthenticated users (these vulnerabilities receive a CVSS Base Score of 7.5). Such vulnerabilities may result in complete takeover of the targeted machine (for the CVSS 10.0), or may result in allowing the attacker the ability to create a denial of service against the affected system or even hijacking or stealing all the data hosted by the compromised system (for the CVSS 7.5). The bottom line is that organizations should assume the worst case: that the most critical vulnerabilities are present in their unsupported version; therefore, it is Oracle's recommendation that all organizations move to supported systems and apply security patches in a timely fashion. Organizations that currently run supported versions but may be late in their security patch release level can quickly catch up because most Critical Patch Updates are cumulative. With a few exceptions noted in Oracle's Critical Patch Update Advisory, the application of the most recent Critical Patch Update will bring these products to current security patch level and provide the organization with the best possible security posture for their patch level. Furthermore, organizations are encouraged to upgrade to most recent versions as this will greatly improve their security posture. At Oracle, our security fixing policies state that security fixes are produced for the main code line first, and as a result, our products benefit from the mistakes made in previous version(s). Our ongoing assurance effort ensures that we work diligently to fix the vulnerabilities we find, and aim at constantly improving the security posture our products provide by default. Patch sets include numerous in-depth fixes in addition to those delivered through the Critical Patch Update and, in certain instances, important security fixes require major architectural changes that can only be included in new product releases (and cannot be backported through the Critical Patch Update program). For More Information: • Mary Ann Davidson is giving a webcast interview on Oracle Software Security Assurance on February 24th. The registration link for attending this webcast is located at http://event.on24.com/r.htm?e=280304&s=1&k=6A7152F62313CA09F77EBCEEA9B6294F&partnerref=EricMblog • A blog entry discussing Oracle's practices for ensuring the quality of Critical patch Updates can be found at http://blogs.oracle.com/security/2009/07/ensuring_critical_patch_update_quality.html • The blog entry "To patch or not to patch" is located at http://blogs.oracle.com/security/2008/01/to_patch_or_not_to_patch.html • Oracle's Support Policies are located at http://www.oracle.com/us/support/policies/index.html • The Critical Patch Update & Security Alert page is located at http://www.oracle.com/technetwork/topics/security/alerts-086861.html

    Read the article

  • SSIS: Building SQL databases on-the-fly using concatenated SQL scripts

    - by DrJohn
    Over the years I have developed many techniques which help automate the whole SQL Server build process. In my current process, where I need to build entire OLAP data marts on-the-fly, I make regular use of a simple but very effective mechanism to concatenate all the SQL Scripts together from my SSMS (SQL Server Management Studio) projects. This proves invaluable because in two clicks I can redeploy an entire SQL Server database with all tables, views, stored procedures etc. Indeed, I can also use the concatenated SQL scripts with SSIS to build SQL Server databases on-the-fly. You may be surprised to learn that I often redeploy the database several times per day, or even several times per hour, during the development process. This is because the deployment errors are logged and you can quickly see where SQL Scripts have object dependency errors. For example, after changing a table structure you may have forgotten to change any related views. The deployment log immediately points out all the objects which failed to build so you can fix and redeploy the database very quickly. The alternative approach (i.e. doing changes in the database directly using the SSMS UI) would require you to check all dependent objects before making changes. The chances are that you will miss something and wonder why your app returns the wrong data – a common problem caused by changing a table without re-creating dependent views. Using SQL Projects in SSMS A great many developers fail to make use of SQL Projects in SSMS (SQL Server Management Studio). To me they are invaluable way of organizing your SQL Scripts. The screenshot below shows a typical SSMS solution made up of several projects – one project for tables, another for views etc. The key point is that the projects naturally fall into the right order in file system because of the project name. The number in the folder or file name ensures that the projects the SQL scripts are concatenated together in the order that they need to be executed. Hence the script filenames start with 100, 110 etc. Concatenating SQL Scripts To concatenate the SQL Scripts together into one file, I use notepad.exe to create a simple batch file (see example screenshot) which uses the TYPE command to write the content of the SQL Script files into a combined file. As the SQL Scripts are in several folders, I simply use several TYPE command multiple times and append the output together. If you are unfamiliar with batch files, you may not know that the angled bracket (>) means write output of the program into a file. Two angled brackets (>>) means append output of this program into a file. So the command-line DIR > filelist.txt would write the content of the DIR command into a file called filelist.txt. In the example shown above, the concatenated file is called SB_DDS.sql If, like me you place the concatenated file under source code control, then the source code control system will change the file's attribute to "read-only" which in turn would cause the TYPE command to fail. The ATTRIB command can be used to remove the read-only flag. Using SQLCmd to execute the concatenated file Now that the SQL Scripts are all in one big file, we can execute the script against a database using SQLCmd using another batch file as shown below: SQLCmd has numerous options, but the script shown above simply executes the SS_DDS.sql file against the SB_DDS_DB database on the local machine and logs the errors to a file called SB_DDS.log. So after executing the batch file you can simply check the error log to see if your database built without a hitch. If you have errors, then simply fix the source files, re-create the concatenated file and re-run the SQLCmd to rebuild the database. This two click operation allows you to quickly identify and fix errors in your entire database definition.Using SSIS to execute the concatenated file To execute the concatenated SQL script using SSIS, you simply drop an Execute SQL task into your package and set the database connection as normal and then select File Connection as the SQLSourceType (as shown below). Create a file connection to your concatenated SQL script and you are ready to go.   Tips and TricksAdd a new-line at end of every fileThe most common problem encountered with this approach is that the GO statement on the last line of one file is placed on the same line as the comment at the top of the next file by the TYPE command. The easy fix to this is to ensure all your files have a new-line at the end.Remove all USE database statementsThe SQLCmd identifies which database the script should be run against.  So you should remove all USE database commands from your scripts - otherwise you may get unintentional side effects!!Do the Create Database separatelyIf you are using SSIS to create the database as well as create the objects and populate the database, then invoke the CREATE DATABASE command against the master database using a separate package before calling the package that executes the concatenated SQL script.    

    Read the article

  • No More NCrunch For Me

    - by Steve Wilkes
    When I opened up Visual Studio this morning, I was greeted with this little popup: NCrunch is a Visual Studio add-in which runs your tests while you work so you know if and when you've broken anything, as well as providing coverage indicators in the IDE and coverage metrics on demand. It recently went commercial (which I thought was fair enough), and time is running out for the free version I've been using for the last couple of months. From my experiences using NCrunch I'm going to let it expire, and go about my business without it. Here's why. Before I start, let me say that I think NCrunch is a good product, which is to say it's had a positive impact on my programming. I've used it to help test-drive a library I'm making right from the start of the project, and especially at the beginning it was very useful to have it run all my tests whenever I made a change. The first problem is that while that was cool to start with, it’s recently become a bit of a chore. Problems Running Tests NCrunch has two 'engine modes' in which it can run tests for you - it can run all your tests when you make a change, or it can figure out which tests were impacted and only run those. Unfortunately, it became clear pretty early on that that second option (which is marked as 'experimental') wasn't really working for me, so I had to have it run everything. With a smallish number of tests and while I was adding new features that was great, but I've now got 445 tests (still not exactly loads) and am more in a 'clean and tidy' mode where I know that a change I'm making will probably only affect a particular subset of the tests. With that in mind it's a bit of a drag sitting there after I make a change and having to wait for NCrunch to run everything. I could disable it and manually run the tests I know are impacted, but then what's the point of having NCrunch? If the 'impacted only' engine mode worked well this problem would go away, but that's not what I found. Secondly, what's wrong with this picture? I've got 445 tests, and NCrunch has queued 455 tests to run. So it's queued duplicate tests - in this quickly-screenshotted case 10, but I've seen the total queue get up over 600. If I'm already itchy waiting for it to run all my tests against a change I know only affects a few, I'm even itchier waiting for it to run a lot of them twice. Problems With Code Coverage NCrunch marks each line of code with a dot to say if it's covered by tests - a black dot says the line isn't covered, a red dot says it's covered but at least one of the covering tests is failing, and a green dot means all the covering tests pass. It also calculates coverage statistics for you. Unfortunately, there's a couple of flaws in the coverage. Firstly, it doesn't support ExcludeFromCodeCoverage attributes. This feature has been requested and I expect will be included in a later release, but right now it doesn't. So this: ...is counted as a non-covered line, and drags your coverage statistics down. Hmph. As well as that, coverage of certain types of code is missed. This: ...is definitely covered. I am 100% absolutely certain it is, by several tests. NCrunch doesn't pick it up, down go my coverage statistics. I've had NCrunch find genuinely uncovered code which I've been able to remove, and that's great, but what's the coverage percentage on this project? Umm... I don't know. Conclusion None of these are major, tool-crippling problems, and I expect NCrunch to get much better in future releases. The current version has some great features, like this: ...that's a line of code with a failing test covering it, and NCrunch can run that failing test and take me to that line exquisitely easily. That's awesome! I'd happily pay for a tool that can do that. But here's the thing: NCrunch (currently) costs $159 (about £100) for a personal licence and $289 (about £180) for a commercial one. I'm not sure which one I'd need as my project is a personal one which I'm intending to open-source, but I'm a professional, self-employed developer, but in any case - that seems like a lot of money for an imperfect tool. If it did everything it's advertised to do more or less perfectly I'd consider it, but it doesn't. So no more NCrunch for me.

    Read the article

  • Managing Dependency Hell with WiX and C#

    - by Tom the Junglist
    We are on the eve of product launch, and at the last minute I am being bombarded with crash reports that appear to be related to our installer, which is a WiX3 project with separate outputs for x86 and x64 builds. These have been an ongoing problem that I always thought were fixed, only to find out that they were still lurking. The product itself is a collection of binaries that communicate with each other via .Net remoting, including a Windows Service and a small COM component that is loaded as an addon in another app. The service runs as SYSTEM, the COM piece runs in a low-rights context, while the other pieces run in normal user contexts. Other pieces include an third-party COM object library DLL and a shared DLL with the .net Remoting interfaces. I've observed flat-out weird behavior with MSI, particularly on version upgrades. Between MS' anal strong-name implementation (specifically, the exact version check before loading a given assembly), a documented WiX/MSI bug that sees critical files erased on upgrades (essentially, if a file in the upgrade MSI has the same version number as the existing install, that file is deleted), and having to work around Wow64 virtualization (x86 MSI can only write to registry/HD locations via Wow64, yet x64 MSIs cannot run on x86 computers...), I am about ready to trash the whole thing and port it over to a different install system. What I am looking for on tips + tricks, techniques, or suggestions on how to properly do things so that I am not fighting with Windows Installer's twisted sense of logic. I am tired of fighting with WiX/MSI/Windows Installer. All it needs to do is place files and registry keys where I tell it to, upgrade them when appropriate, and don't delete anything until the user uninstalls. Instead, dependencies are deleted willy-nilly, bringing up a whole bunch of uncatchable exceptions (can't wrap a try{} block around function declarations) and GPF'ing the whole app. I am particularly interested in 'best practices' and examples regarding shared and dependency DLLs, and any tips on making sure if a file needs to go to GAC, that it actually goes to the GAC and stays there until it is appropriate to remove it. Thanks! Tom

    Read the article

  • file layout and setuptools configuration for the python bit of a multi-language library

    - by dan mackinlay
    So we're writing a full-text search framework MongoDb. MongoDB is pretty much javascript-native, so we wrote the javascript library first, and it works. Now I'm trying to write a python framework for it, which will be partially in python, but partially use those same stored javascript functions - the javascript functions are an intrinsic part of the library. On the other hand, the javascript framework does not depend on python. since they are pretty intertwined it seems like it's worthwhile keeping them in the same repository. I'm trying to work out a way of structuring the whole project to give the javascript and python frameworks equal status (maybe a ruby driver or whatever in the future?), but still allow the python library to install nicely. Currently it looks like this: (simplified a little) javascript/jstest/test1.js javascript/mongo-fulltext/search.js javascript/mongo-fulltext/util.js python/docs/indext.rst python/tests/search_test.py python/tests/__init__.py python/mongofulltextsearch/__init__.py python/mongofulltextsearch/mongo_search.py python/mongofulltextsearch/util.py python/setup.py I've skipped out a few files for simplicity, but you get the general idea; it' a pretty much standard python project... except that it depends critcally ona whole bunch of javascript which is stored in a sibling directory tree. What's the preferred setup for dealing with this kind of thing when it comes to setuptools? I can work out how to use package_data etc to install data files that live inside my python project as per the setuptools docs. The problem is if i want to use setuptools to install stuff, including the javascript files from outside the python code tree, and then also access them in a consistent way when I'm developing the python code and when it is easy_installed to someone's site. Is that supported behaviour for setuptools? Should i be using paver or distutils2 or Distribute or something? (basic distutils is not an option; the whole reason I'm doing this is to enable requirements tracking) How should i be reading the contents of those files into python scripts?

    Read the article

  • Is there any way to combine transparency and "ajax usability" with HTML templates

    - by Sam
    I'm using HTML_Template_Flexy in PHP but the question should apply to any language or template library. I am outputting a list of relatively complex objects. In the beginning I just iterated over a list of the objects and called a toHtml method on them. When I was about to have my layout designer look over the template I noticed that it was too opaque and that he would have ended up looking through and/or editing many additional php source files to see what really gets generated by the toHtml method. So I extracted most of the HTML strings in the php classes up to the template which made for one clear file where you can see the whole page structure at once. However this causes problems when you want to add an object to the list using javascript. Then I have to keep the old toHtml method and maintain both the main template and the html strings at the same time, so I can output just the HTML for a new object that should be added to the page. So I'm back to the idea of using smaller templates for the objects that make up the page, but I was wondering if there was some easy way of having my cake and eating it too by having one template that shows the whole page but also the mini-templates for smaller objects on the page. Edit: Yes, updating the page is not a problem at all. My concern is with having both maintainability and transparency of the template files. If I have one single template for the whole page, then I must maintain mini-templates of the objects that are shown on the page. If I just have the mini-templates and include them from the higher-level template it becomes more difficult to look at the top-level html and imagine what the end result will look like.

    Read the article

< Previous Page | 246 247 248 249 250 251 252 253 254 255 256 257  | Next Page >