Search Results

Search found 1898 results on 76 pages for 'dd dent'.

Page 26/76 | < Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >

• Various problems with software raid1 array built with Samsung 840 Pro SSDs

  - by Andy B

  I am bringing to ServerFault a problem that is tormenting me for 6+ months. I have a CentOS 6 (64bit) server with an md software raid-1 array with 2 x Samsung 840 Pro SSDs (512GB). Problems: Serious write speed problems: root [~]# time dd if=arch.tar.gz of=test4 bs=2M oflag=sync 146+1 records in 146+1 records out 307191761 bytes (307 MB) copied, 23.6788 s, 13.0 MB/s real 0m23.680s user 0m0.000s sys 0m0.932s When doing the above (or any other larger copy) the load spikes to unbelievable values (even over 100) going up from ~ 1. When doing the above I've also noticed very weird iostat results: Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 0.00 1589.50 0.00 54.00 0.00 13148.00 243.48 0.60 11.17 0.46 2.50 sdb 0.00 1627.50 0.00 16.50 0.00 9524.00 577.21 144.25 1439.33 60.61 100.00 md1 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 md2 0.00 0.00 0.00 1602.00 0.00 12816.00 8.00 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 And it keeps it this way until it actually writes the file to the device (out from swap/cache/memory). The problem is that the second SSD in the array has svctm and await roughly 100 times larger than the second. For some reason the wear is different between the 2 members of the array root [~]# smartctl --attributes /dev/sda | grep -i wear 177 Wear_Leveling_Count 0x0013 094% 094 000 Pre-fail Always - 180 root [~]# smartctl --attributes /dev/sdb | grep -i wear 177 Wear_Leveling_Count 0x0013 070% 070 000 Pre-fail Always - 1005 The first SSD has a wear of 6% while the second SSD has a wear of 30%!! It's like the second SSD in the array works at least 5 times as hard as the first one as proven by the first iteration of iostat (the averages since reboot): Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 10.44 51.06 790.39 125.41 8803.98 1633.11 11.40 0.33 0.37 0.06 5.64 sdb 9.53 58.35 322.37 118.11 4835.59 1633.11 14.69 0.33 0.76 0.29 12.97 md1 0.00 0.00 1.88 1.33 15.07 10.68 8.00 0.00 0.00 0.00 0.00 md2 0.00 0.00 1109.02 173.12 10881.59 1620.39 9.75 0.00 0.00 0.00 0.00 md0 0.00 0.00 0.41 0.01 3.10 0.02 7.42 0.00 0.00 0.00 0.00 What I've tried: I've updated the firmware to DXM05B0Q (following reports of dramatic improvements for 840Ps after this update). I have looked for "hard resetting link" in dmesg to check for cable/backplane issues but nothing. I have checked the alignment and I believe they are aligned correctly (1MB boundary, listing below) I have checked /proc/mdstat and the array is Optimal (second listing below). root [~]# fdisk -ul /dev/sda Disk /dev/sda: 512.1 GB, 512110190592 bytes 255 heads, 63 sectors/track, 62260 cylinders, total 1000215216 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00026d59 Device Boot Start End Blocks Id System /dev/sda1 2048 4196351 2097152 fd Linux raid autodetect Partition 1 does not end on cylinder boundary. /dev/sda2 * 4196352 4605951 204800 fd Linux raid autodetect Partition 2 does not end on cylinder boundary. /dev/sda3 4605952 814106623 404750336 fd Linux raid autodetect root [~]# fdisk -ul /dev/sdb Disk /dev/sdb: 512.1 GB, 512110190592 bytes 255 heads, 63 sectors/track, 62260 cylinders, total 1000215216 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0003dede Device Boot Start End Blocks Id System /dev/sdb1 2048 4196351 2097152 fd Linux raid autodetect Partition 1 does not end on cylinder boundary. /dev/sdb2 * 4196352 4605951 204800 fd Linux raid autodetect Partition 2 does not end on cylinder boundary. /dev/sdb3 4605952 814106623 404750336 fd Linux raid autodetect /proc/mdstat root # cat /proc/mdstat Personalities : [raid1] md0 : active raid1 sdb2[1] sda2[0] 204736 blocks super 1.0 [2/2] [UU] md2 : active raid1 sdb3[1] sda3[0] 404750144 blocks super 1.0 [2/2] [UU] md1 : active raid1 sdb1[1] sda1[0] 2096064 blocks super 1.1 [2/2] [UU] unused devices: Running a read test with hdparm root [~]# hdparm -t /dev/sda /dev/sda: Timing buffered disk reads: 664 MB in 3.00 seconds = 221.33 MB/sec root [~]# hdparm -t /dev/sdb /dev/sdb: Timing buffered disk reads: 288 MB in 3.01 seconds = 95.77 MB/sec But look what happens if I add --direct root [~]# hdparm --direct -t /dev/sda /dev/sda: Timing O_DIRECT disk reads: 788 MB in 3.01 seconds = 262.08 MB/sec root [~]# hdparm --direct -t /dev/sdb /dev/sdb: Timing O_DIRECT disk reads: 534 MB in 3.02 seconds = 176.90 MB/sec Both tests increase but /dev/sdb doubles while /dev/sda increases maybe 20%. I just don't know what to make of this. As suggested by Mr. Wagner I've done another read test with dd this time and it confirms the hdparm test: root [/home2]# dd if=/dev/sda of=/dev/null bs=1G count=10 10+0 records in 10+0 records out 10737418240 bytes (11 GB) copied, 38.0855 s, 282 MB/s root [/home2]# dd if=/dev/sdb of=/dev/null bs=1G count=10 10+0 records in 10+0 records out 10737418240 bytes (11 GB) copied, 115.24 s, 93.2 MB/s So sda is 3 times faster than sdb. Or maybe sdb is doing also something else besides what sda does. Is there some way to find out if sdb is doing more than what sda does? UPDATE Again, as suggested by Mr. Wagner, I have swapped the 2 SSDs. And as he thought it would happen, the problem moved from sdb to sda. So I guess I'll RMA one of the SSDs. I wonder if the cage might be problematic. What is wrong with this array? Please help!

  Read the article

• Setting the date format in Atlassian Crucible

  - by pwan

  When I set up a review in Atlassian Crucible, and I set a date, it displays it in DD/MM/YYYY I'd like to switch that over to MM/DD/YYYY, but I don't see anywhere in the configuration to switch that. The closest setting I see is for the timezone, which I have set to EST. I have Crucible running on a CentOS 6.2 machine that's set to UTC I'm using Crucible version 2.7.14 Build:20120612060728 2012-06-12 My locale is currently set to en_US.UTF-8 > locale | grep LC_TIME LC_TIME="en_US.UTF-8" Can someone point out how I can switch the date format in Crucible ?

  Read the article

• How to list all 2nd level subfolders and delete un-required ones?

  - by AllSolutions

  I provide support to a lot of clients. I have created a folder for each client, and under each client folder, I create a folder for the date on which the issue was reported. Now due to growing data, I want to delete all issues for all clients which are before a cut off date. The problem is while creating the date folder, I have not always followed a specific convention, some are creating using dd-MM-yyyy, some are using dd.MM.yyyy, etc. Is there a quick way I can list all such date subfolders, and then choose which ones I do not want, and delete them? I am using Windows XP SP 2 32 bit. Thanks.

  Read the article

• Converting an ancient RH8 system to VMware ESXi

  - by donatello

  I am curious to know what options I have to convert a very old RedHat8 machine to a virtual one on ESXi. Looking at VMware Converter it seems there's an option to login to the RH8 using SSH, and from there it will convert to the ESXi-server. That makes me a bit nervous though, exactly what is happening there? The RH8 machine is slightly critical, and if anything messes up it'll likely result in many hours extra work. :( Another option I thought of was to boot a LiveCD on RH8-system and create a raw "dd dump" of the disk. The similar method is used to restore the image, I boot a LiveCD on the VM in ESXi and use "dd" to write it to disk. Is there any other option I could use? I'm using the cheap version of ESXi, hence I have no access to the Converter BootCD so these rather cumbersome methods is the only I can think of. :)

  Read the article

• Xen P2V for large physical hosts with much free space

  - by Sirex

  I need to P2V a rhel5 machine to xen under rhel5. I know I can use dd if=/dev/sda then using virt-install --import on the host, but the downside of this is the original machine has 80% free space on its drive. Does anyone know of (or can document) a quick and easy method which works reliably, to produce a bootable xen image which can run under a hvm in such cases ? I tried clonezilla to make the image, to avoid the free space problem, but it failed to do the clone with "something went wrong" (useless info, i know). At the moment im looking at doing a dd of each partition, and a file level copy of the partition which is mostly empty, then creating a new virtual disk, copying the partitions over to it by mounting both the new image and the virtual drive on a second vm, then copying the boot sectors over, then copying the file level backup..... there must be an easier way ? Oh, and budget is $0. :)

  Read the article

• Why grep -i is so slow? How to do it faster for ASCII?

  - by Vi.

  $ time lzop -d < tvtropes-index.lzo | egrep -B 5 '[Dd][eE][sS][cC][eE][nN][dD] ?[Ff][rR][oO][mM]' real 0m0.438s $ time lzop -d < tvtropes-index.lzo | egrep -B 5 'descend ?from' -i real 0m11.294s Both search insensitively. why -i so slow? How to make fast grep -i without entering things [iI][nN] [tT][hH][iI][sS] [wW][aA][Yy]? For example, perl -ne 'print if /descend ?from/i' works fast, but '-B 5' is not as trivial to implement as in grep (as well as other options).

  Read the article

• What is fastest way to backup a disk image over LAN?

  - by David Balažic

  Sometimes I boot sysrescd or a similar live linux on a PC to backup the hardrive over local network to my server. I noticed many times, that the transfer speed is not optimal (slower than HDD and network speed). Any rules of thumb what to do and what to avoid? What I typically do is something like: dd bs=16M if=/dev/sda | nc ... # on client nc ... | dd bs=16M of=/destination/disk/backup1 # on server I also "throw" in lzop (other are way too slow) and sometimes on the fly md5sum calculation (both of uncompressed and compress source). I try to add (m)buffer (or other alternatives) to improve throughput (and get a progress indicator). I noticed that even with enough free CPU, adding commands to the pipeline slows things down. Typically the destination is on a NTFS volume (accessed via ntfs-3g, with the _big_writes_ option).

  Read the article

• Why is 'grep -i' so slow? How to do it faster for ASCII?

  - by Vi.

  Consider: $ time lzop -d < tvtropes-index.lzo | egrep -B 5 '[Dd][eE][sS][cC][eE][nN][dD] ?[Ff][rR][oO][mM]' real 0m0.438s $ time lzop -d < tvtropes-index.lzo | egrep -B 5 'descend ?from' -i real 0m11.294s Both search case insensitively. Why is the -i version so slow? How do I make grep -i fast without entering things like [iI][nN] [tT][hH][iI][sS] [wW][aA][Yy]? For example, perl -ne 'print if /descend ?from/i' works fast, but '-B 5' is not as trivial to implement as in grep (as well as other options).

  Read the article

• "The requested operation could not be completed due to a file system limitation" 3202

  - by user46529

  I backup SQL Server database and it fails BACKUP DATABASE dd TO DISK = '\backupServer\backups\dd.bak' WITH COMPRESSION, CHECKSUM, NOFORMAT, INIT , BlockSize = 65536 , BufferCount = 2200 , MaxTransferSize = 4194304 The backup size is 3TB and I have 6TB free space on bacup server. I am using backup parameters per SQLCAT whitepaper. Everything works ok when I backup to local HDD and it always fails when I backup to network share. After about 6 hours. Can't find why. Thank you. Yes. The backup over the network is fastest and saves me 3Tb of local disk space :) Thanks for pointing to the memory issue. I left 4Gb to OS and it worked!

  Read the article

• In OpenOffice Spreadsheet, how can I set the default Date format?

  - by Joe Casadonte

  I'm using OO 3.1.1 on Ubuntu 9.10 (in case that matters to the answer). I like my dates to appear as YYYY-MM-DD. I can't think of a time when I want to see a date in any other format, so I'm constantly changing how dates look. That's manageable, though annoying. What's gotten me to the point of posting is that when I edit a cell with a date value, I have to edit it in the format MM/DD/YYYY, which is really, really annoying, as I'm usually mucking with the day (or possibly the month), and very seldom the year. So there's lots of cursor or mouse use, wasting my time. So is there a way that I can change how dates are edited, or at least the default display format? Thanks!

  Read the article

• RAID 5 heavy IO hard freezes Ubuntu: Why?

  - by Luke has no name

  I have a software RAID 5 partition on LVM in Ubuntu (desktop, actually, but I'm using it as a server). I have been rsyncing a ton of data to it, and the computer was hard freezing, as in I needed to press "Reset". So I thought it was rsync. But I decided I'd try a dd if=/dev/zero of=/path/to/raid5 and sure enough, the computer locked up. Did an identical dd to a JBOD partition on the same machine, and it didn't crash. Assuming a clean RAID5 partition, tri-core processor 2GB of ram, 6GB swap, what could be causing this?

  Read the article

• Creating bootable Fedora USB with persistent storage

  - by dooffas

  I am attempting to burn the full Fedora 19 x86_64 DVD iso to a USB drive and have a separate partition on it for a kickstart file / other media that will be installed in the kickstart process. With the Ubuntu server 12 iso, you can simply dd the iso to the usb drive: dd if=/path/to/iso of=/dev/sdb Once the iso has been burnt, open gparted and create a ext2 parition in the allocated space. However, this does not seem to work with the Fedora ISO. When loading the USB drive in gparted I get a warning and an error: Warning: The driver descriptor says the physical block size is 2048 bytes, but Linux says it is 512 bytes. Error: The partition's data region doesn't occupy the entire partition. Ignoring both of these errors allows gparted to load the usb drive, however it shows a blank drive with no partition table. Has anyone come across this before? From what I have found, it may have something to do with the fact that Fedora use isohybrid.

  Read the article

• type mismatch errors querying data from spreadsheet

  - by user2984933

  In EXCEL 2010 I am trying to querying data in another spreadsheet. The data range in the source sheet/ file is named (DATABASE). The Date field in the database is formatted as short date and when I query the date without criteria I get a different format of European datesYYYY-MM-DD with time in the results. When I use criteria and a specific date in the date field criteria grid using English format MM-DD-YYYY I get results. When I set parameters looking at destination file cells for the date for the parameters, I get Type mismatch EVEN THOUGHT THE CELLS ARE Short date Formatted. This worked perfectly in my 2003 version of EXCEL. Now I am running Win 7 -64 and Office 2010 Pro. Why does the query throw Mismatch with cell references for the parameters but accepts hard value dates in any date format? (MSQRY32.EXE)

  Read the article

• How to convert number(16,10) to date in oracle

  - by Elad

  Hi, I'm trying to read the borland starteam application oracle database and I noticed that they represent their date as a number(16,10) column I think it is not timestamp or epoc. for instance, I have the number: 37137.4347569444, how can I read it as date? I saw that the database has a stored procedure. CONVERT_DATE: CREATE OR REPLACE procedure STARBASE.convert_date ( number_of_days IN integer , nDate OUT number) is nDateOffset number; CurrentDate date; Month integer; Day integer; year number; success boolean := false; bLeapYear boolean:=false; nDaysInMonths number; nLeapDays integer; fDate number (16,10); rgMonthDays number(5,0); begin select sysdate - number_of_days into CurrentDate from dual; nDateOffset := 693959; select to_number(substr((TO_CHAR (CurrentDate, 'MM-DD-YYYY')) , 1, 2), '99') - 1 into month from dual; select to_number(substr((TO_CHAR (CurrentDate, 'MM-DD-YYYY')) , 4, 2), '99') - 1 into day from dual; select to_number(substr((TO_CHAR (CurrentDate, 'MM-DD-YYYY')) , 7, 4), '9999') into year from dual; if ( mod(year , 4) = 0 ) and ( ( mod(year , 400) = 0) or ( mod(year , 100) < 0 )) then bLeapYear :=true; end if; nLeapDays := 0; if ( bLeapYear = true) and ( Day = 28) and ( Month = 1 ) then nLeapDays := 1; end if; select substr(to_char(last_day(CurrentDate) , 'DD-MM-YYYY') , 1 , 2) into nDaysInMonths from dual; if Month = 0 then rgMonthDays := 0; elsif Month = 1 then rgMonthDays := 31; elsif Month = 2 then rgMonthDays := 59; elsif Month = 3 then rgMonthDays := 90; elsif Month = 4 then rgMonthDays := 120; elsif Month = 5 then rgMonthDays := 151; elsif Month = 6 then rgMonthDays := 181; elsif Month = 7 then rgMonthDays := 212; elsif Month = 8 then rgMonthDays := 243; elsif Month = 9 then rgMonthDays := 273; elsif Month = 10 then rgMonthDays := 304; elsif Month = 11 then rgMonthDays := 334; elsif Month = 12 then rgMonthDays := 365; end if; nDate := Year*365 + Year/4 - Year/100 + Year/400 + rgMonthDays + Day + 1; if( Month < 2 ) and ( bLeapYear = true) then nDate := nDate - 1; end if; nDate := nDate - nDateOffset; exception when others then raise; end convert_date; I don't know how to use it. how can i read it anyway? Please help. thank you

  Read the article

• WPF MVVM TreeView item source losing context after command

  - by user3955716

  I have a treeview which contains files, every view model holds an item source which is an ObservableCollection with files items: public ObservableCollection<CMItemFileNode> SubItemNode On each item i have context menu options (Delete, Execute..). If i move from one viewModel to another the ObservableCollection of files updated correctly and presented correctly but, when i perform a context menu command like delete file item, the command execute good but when i move to another view model (which holds SubItemNode ObservableCollection of is own) after the command executed the WPF still thinks i'm in the last view model i was in and not the one i'm really on. Very important to mention is that when i update to .net 4.5 (which unfortunantly i can't do) everything is ok and the ObservableCollection addresses the correct view model. Here is the treeView: <TreeView x:Name="Files" Margin="0,5,5,0" Grid.Row="6" Grid.Column="2" ItemsSource="{Binding SubItemNode}" HorizontalAlignment="Stretch" HorizontalContentAlignment="Stretch" VerticalAlignment="Stretch" Height="300" Grid.RowSpan="6" Width="300" dd:DragDrop.IsDragSource="True" dd:DragDrop.IsDropTarget="True" dd:DragDrop.DropHandler="{Binding}" dd:DragDrop.UseDefaultDragAdorner="True"> <TreeView.Resources> <Style TargetType="{x:Type TreeView}"> <Setter Property="local:CMTreeViewFilesBehavior.IsTreeViewFilesBehavior" Value="True"/> </Style> <Style TargetType="{x:Type TreeViewItem}"> <Setter Property="IsSelected" Value="{Binding IsSelected}" /> <Setter Property="local:CMTreeViewFilesItemBehavior.IsTreeViewFilesItemBehavior" Value="True"/> </Style> <SolidColorBrush x:Key="{x:Static SystemColors.HighlightBrushKey}" Color="Transparent" /> <SolidColorBrush x:Key="{x:Static SystemColors.HighlightTextBrushKey}" Color="Black" /> </TreeView.Resources> <TreeView.ContextMenu> <ContextMenu> <MenuItem Header="View File" Command="{Binding ExecuteFileCommand}" /> <Separator /> <MenuItem Header="Delete all" Command="{Binding DeleteAllFilesCommand}" /> <MenuItem Header="Delete selected" Command="{Binding DeleteSelectedFilesCommand}" /> </ContextMenu> </TreeView.ContextMenu> <TreeView.ItemTemplate> <HierarchicalDataTemplate ItemsSource="{Binding SubItemNode}" > <Grid> <Grid.ColumnDefinitions> <ColumnDefinition Width="Auto"/> <ColumnDefinition Width="*"/> </Grid.ColumnDefinitions> <Image Grid.Column="0" Margin="2" Width="32" Height="18" Source="{Binding Path=Icon}" HorizontalAlignment="Left" VerticalAlignment="Center" /> <TextBlock Text="{Binding Path=Name}" Grid.Column="1" Margin="2" VerticalAlignment="Center" Foreground="{Binding Path=Status, Converter={StaticResource ItemFileStatusToColor}}" FontWeight="{Binding Path=IsSelected, Converter={StaticResource BoolToFontWidth}}"/> </Grid> </HierarchicalDataTemplate> </TreeView.ItemTemplate> </TreeView> Am I doing somthing wrong? and why in .net 4.5 it works well ?

  Read the article

• How to Reuse Your Old Wi-Fi Router as a Network Switch

  - by Jason Fitzpatrick

  Just because your old Wi-Fi router has been replaced by a newer model doesn’t mean it needs to gather dust in the closet. Read on as we show you how to take an old and underpowered Wi-Fi router and turn it into a respectable network switch (saving your $20 in the process). Image by mmgallan. Why Do I Want To Do This? Wi-Fi technology has changed significantly in the last ten years but Ethernet-based networking has changed very little. As such, a Wi-Fi router with 2006-era guts is lagging significantly behind current Wi-Fi router technology, but the Ethernet networking component of the device is just as useful as ever; aside from potentially being only 100Mbs instead of 1000Mbs capable (which for 99% of home applications is irrelevant) Ethernet is Ethernet. What does this matter to you, the consumer? It means that even though your old router doesn’t hack it for your Wi-Fi needs any longer the device is still a perfectly serviceable (and high quality) network switch. When do you need a network switch? Any time you want to share an Ethernet cable among multiple devices, you need a switch. For example, let’s say you have a single Ethernet wall jack behind your entertainment center. Unfortunately you have four devices that you want to link to your local network via hardline including your smart HDTV, DVR, Xbox, and a little Raspberry Pi running XBMC. Instead of spending $20-30 to purchase a brand new switch of comparable build quality to your old Wi-Fi router it makes financial sense (and is environmentally friendly) to invest five minutes of your time tweaking the settings on the old router to turn it from a Wi-Fi access point and routing tool into a network switch–perfect for dropping behind your entertainment center so that your DVR, Xbox, and media center computer can all share an Ethernet connection. What Do I Need? For this tutorial you’ll need a few things, all of which you likely have readily on hand or are free for download. To follow the basic portion of the tutorial, you’ll need the following: 1 Wi-Fi router with Ethernet ports 1 Computer with Ethernet jack 1 Ethernet cable For the advanced tutorial you’ll need all of those things, plus: 1 copy of DD-WRT firmware for your Wi-Fi router We’re conducting the experiment with a Linksys WRT54GL Wi-Fi router. The WRT54 series is one of the best selling Wi-Fi router series of all time and there’s a good chance a significant number of readers have one (or more) of them stuffed in an office closet. Even if you don’t have one of the WRT54 series routers, however, the principles we’re outlining here apply to all Wi-Fi routers; as long as your router administration panel allows the necessary changes you can follow right along with us. A quick note on the difference between the basic and advanced versions of this tutorial before we proceed. Your typical Wi-Fi router has 5 Ethernet ports on the back: 1 labeled “Internet”, “WAN”, or a variation thereof and intended to be connected to your DSL/Cable modem, and 4 labeled 1-4 intended to connect Ethernet devices like computers, printers, and game consoles directly to the Wi-Fi router. When you convert a Wi-Fi router to a switch, in most situations, you’ll lose two port as the “Internet” port cannot be used as a normal switch port and one of the switch ports becomes the input port for the Ethernet cable linking the switch to the main network. This means, referencing the diagram above, you’d lose the WAN port and LAN port 1, but retain LAN ports 2, 3, and 4 for use. If you only need to switch for 2-3 devices this may be satisfactory. However, for those of you that would prefer a more traditional switch setup where there is a dedicated WAN port and the rest of the ports are accessible, you’ll need to flash a third-party router firmware like the powerful DD-WRT onto your device. Doing so opens up the router to a greater degree of modification and allows you to assign the previously reserved WAN port to the switch, thus opening up LAN ports 1-4. Even if you don’t intend to use that extra port, DD-WRT offers you so many more options that it’s worth the extra few steps. Preparing Your Router for Life as a Switch Before we jump right in to shutting down the Wi-Fi functionality and repurposing your device as a network switch, there are a few important prep steps to attend to. First, you want to reset the router (if you just flashed a new firmware to your router, skip this step). Following the reset procedures for your particular router or go with what is known as the “Peacock Method” wherein you hold down the reset button for thirty seconds, unplug the router and wait (while still holding the reset button) for thirty seconds, and then plug it in while, again, continuing to hold down the rest button. Over the life of a router there are a variety of changes made, big and small, so it’s best to wipe them all back to the factory default before repurposing the router as a switch. Second, after resetting, we need to change the IP address of the device on the local network to an address which does not directly conflict with the new router. The typical default IP address for a home router is 192.168.1.1; if you ever need to get back into the administration panel of the router-turned-switch to check on things or make changes it will be a real hassle if the IP address of the device conflicts with the new home router. The simplest way to deal with this is to assign an address close to the actual router address but outside the range of addresses that your router will assign via the DHCP client; a good pick then is 192.168.1.2. Once the router is reset (or re-flashed) and has been assigned a new IP address, it’s time to configure it as a switch. Basic Router to Switch Configuration If you don’t want to (or need to) flash new firmware onto your device to open up that extra port, this is the section of the tutorial for you: we’ll cover how to take a stock router, our previously mentioned WRT54 series Linksys, and convert it to a switch. Hook the Wi-Fi router up to the network via one of the LAN ports (consider the WAN port as good as dead from this point forward, unless you start using the router in its traditional function again or later flash a more advanced firmware to the device, the port is officially retired at this point). Open the administration control panel via  web browser on a connected computer. Before we get started two things: first,  anything we don’t explicitly instruct you to change should be left in the default factory-reset setting as you find it, and two, change the settings in the order we list them as some settings can’t be changed after certain features are disabled. To start, let’s navigate to Setup ->Basic Setup. Here you need to change the following things: Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable Save with the “Save Settings” button and then navigate to Setup -> Advanced Routing: Operating Mode: Router This particular setting is very counterintuitive. The “Operating Mode” toggle tells the device whether or not it should enable the Network Address Translation (NAT)  feature. Because we’re turning a smart piece of networking hardware into a relatively dumb one, we don’t need this feature so we switch from Gateway mode (NAT on) to Router mode (NAT off). Our next stop is Wireless -> Basic Wireless Settings: Wireless SSID Broadcast: Disable Wireless Network Mode: Disabled After disabling the wireless we’re going to, again, do something counterintuitive. Navigate to Wireless -> Wireless Security and set the following parameters: Security Mode: WPA2 Personal WPA Algorithms: TKIP+AES WPA Shared Key: [select some random string of letters, numbers, and symbols like JF#d$di!Hdgio890] Now you may be asking yourself, why on Earth are we setting a rather secure Wi-Fi configuration on a Wi-Fi router we’re not going to use as a Wi-Fi node? On the off chance that something strange happens after, say, a power outage when your router-turned-switch cycles on and off a bunch of times and the Wi-Fi functionality is activated we don’t want to be running the Wi-Fi node wide open and granting unfettered access to your network. While the chances of this are next-to-nonexistent, it takes only a few seconds to apply the security measure so there’s little reason not to. Save your changes and navigate to Security ->Firewall. Uncheck everything but Filter Multicast Firewall Protect: Disable At this point you can save your changes again, review the changes you’ve made to ensure they all stuck, and then deploy your “new” switch wherever it is needed. Advanced Router to Switch Configuration For the advanced configuration, you’ll need a copy of DD-WRT installed on your router. Although doing so is an extra few steps, it gives you a lot more control over the process and liberates an extra port on the device. Hook the Wi-Fi router up to the network via one of the LAN ports (later you can switch the cable to the WAN port). Open the administration control panel via web browser on the connected computer. Navigate to the Setup -> Basic Setup tab to get started. In the Basic Setup tab, ensure the following settings are adjusted. The setting changes are not optional and are required to turn the Wi-Fi router into a switch. WAN Connection Type: Disabled Local IP Address: [different than the primary router, e.g. 192.168.1.2] Subnet Mask: [same as the primary router, e.g. 255.255.255.0] DHCP Server: Disable In addition to disabling the DHCP server, also uncheck all the DNSMasq boxes as the bottom of the DHCP sub-menu. If you want to activate the extra port (and why wouldn’t you), in the WAN port section: Assign WAN Port to Switch [X] At this point the router has become a switch and you have access to the WAN port so the LAN ports are all free. Since we’re already in the control panel, however, we might as well flip a few optional toggles that further lock down the switch and prevent something odd from happening. The optional settings are arranged via the menu you find them in. Remember to save your settings with the save button before moving onto a new tab. While still in the Setup -> Basic Setup menu, change the following: Gateway/Local DNS : [IP address of primary router, e.g. 192.168.1.1] NTP Client : Disable The next step is to turn off the radio completely (which not only kills the Wi-Fi but actually powers the physical radio chip off). Navigate to Wireless -> Advanced Settings -> Radio Time Restrictions: Radio Scheduling: Enable Select “Always Off” There’s no need to create a potential security problem by leaving the Wi-Fi radio on, the above toggle turns it completely off. Under Services -> Services: DNSMasq : Disable ttraff Daemon : Disable Under the Security -> Firewall tab, uncheck every box except “Filter Multicast”, as seen in the screenshot above, and then disable SPI Firewall. Once you’re done here save and move on to the Administration tab. Under Administration -> Management:  Info Site Password Protection : Enable Info Site MAC Masking : Disable CRON : Disable 802.1x : Disable Routing : Disable After this final round of tweaks, save and then apply your settings. Your router has now been, strategically, dumbed down enough to plod along as a very dependable little switch. Time to stuff it behind your desk or entertainment center and streamline your cabling.     

  Read the article

• Simple scan not working after upgrading to 12.10 (Xubuntu)

  - by mydoghasworms

  Since upgrading to 12.10 (Xubuntu), Simple Scan is not working anymore. I got scanning working with Xsane, but only if Simple Scan has not run before. Otherwise I have to restart the printer/scanner (HP OfficeJet J5783). In kernel.log I see: kernel: [ 1214.120964] usb 2-1.4: >usbfs: process 4412 (simple-scan) did not claim interface 2 before use and in syslog simple-scan: io/hpmud/dot4.c 172: unable to read Dot4ReverseCmd header: No data available simple-scan: io/hpmud/musb.c 1933: invalid Dot4Credit from peripheral simple-scan: io/hpmud/dot4.c 172: unable to read Dot4ReverseCmd header: No data available simple-scan: io/hpmud/musb.c 1933: invalid Dot4Credit from peripheral simple-scan: sane_hpaio_cancel: already cancelled! simple-scan: io/hpmud/dot4.c 172: unable to read Dot4ReverseCmd header: No data available simple-scan: io/hpmud/musb.c 1933: invalid Dot4Credit from peripheral simple-scan: io/hpmud/dot4.c 231: unable to read Dot4ReverseReply header: No data available bytesRead=0 simple-scan: io/hpmud/dot4.c 319: invalid DOT4InitReply retrying command... simple-scan: io/hpmud/dot4.c 172: unable to read Dot4ReverseCmd header: No data available simple-scan: io/hpmud/musb.c 1933: invalid Dot4Credit from peripheral simple-scan: io/hpmud/hpmud.c 342: device_cleanup: device uri=hp:/usb/Officejet_J5700_series?serial=CN81LCV0V604TC simple-scan: io/hpmud/hpmud.c 354: device_cleanup: close device dd=1... simple-scan: io/hpmud/hpmud.c 356: device_cleanup: done closing device dd=1 Any ideas?

  Read the article

• SATA errors reported during boot: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0

  - by digby280

  I have noticed some error during the Linux boot. They seem to continue to occur after the boot adding lines to the log every few seconds. Once booted this normally does not appear to be causing any problems. However, around 1 in 10 boots results in a kernel panic and the computer has on two or three occasions suddenly rebooted after being powered on for a number of hours. I presume the cause of the reboot is a kernel panic as well. I am running Ubuntu 11.10 and I have had Ubuntu installed on the computer for around a year. I have googled around and not found anything useful. I have provided the kernel log lines and the output of smartctl. Can anyone explain exactly what these errors mean, or better still how to resolve them? Apr 2 16:51:27 dell580 kernel: [ 19.831140] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:27 dell580 kernel: [ 19.934194] tg3 0000:03:00.0: eth0: Link is down Apr 2 16:51:28 dell580 kernel: [ 20.929468] tg3 0000:03:00.0: eth0: Link is up at 100 Mbps, full duplex Apr 2 16:51:28 dell580 kernel: [ 20.929471] tg3 0000:03:00.0: eth0: Flow control is on for TX and on for RX Apr 2 16:51:28 dell580 kernel: [ 20.929727] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Apr 2 16:51:29 dell580 kernel: [ 21.609381] EXT4-fs (sdb2): re-mounted. Opts: errors=remount-ro,user_xattr,commit=0 Apr 2 16:51:29 dell580 kernel: [ 21.616515] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:29 dell580 kernel: [ 21.616519] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:29 dell580 kernel: [ 21.616525] ata2.00: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 21.934036] ata2.01: hard resetting link Apr 2 16:51:29 dell580 kernel: [ 22.408890] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.408907] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:29 dell580 kernel: [ 22.440934] ata2.00: configured for UDMA/100 Apr 2 16:51:29 dell580 kernel: [ 22.449040] ata2.01: configured for UDMA/133 Apr 2 16:51:29 dell580 kernel: [ 22.449818] ata2: EH complete Apr 2 16:51:33 dell580 kernel: [ 26.122664] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:33 dell580 kernel: [ 26.122670] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:33 dell580 kernel: [ 26.122677] ata2.00: hard resetting link Apr 2 16:51:33 dell580 kernel: [ 26.442684] ata2.01: hard resetting link Apr 2 16:51:34 dell580 kernel: [ 26.925545] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.925561] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:34 dell580 kernel: [ 26.961542] ata2.00: configured for UDMA/100 Apr 2 16:51:34 dell580 kernel: [ 26.969616] ata2.01: configured for UDMA/133 Apr 2 16:51:34 dell580 kernel: [ 26.970400] ata2: EH complete Apr 2 16:51:35 dell580 kernel: [ 28.111180] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:35 dell580 kernel: [ 28.111184] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:35 dell580 kernel: [ 28.111191] ata2.00: hard resetting link Apr 2 16:51:35 dell580 kernel: [ 28.429674] ata2.01: hard resetting link Apr 2 16:51:36 dell580 kernel: [ 28.904557] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.904572] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:36 dell580 kernel: [ 28.936609] ata2.00: configured for UDMA/100 Apr 2 16:51:36 dell580 kernel: [ 28.944692] ata2.01: configured for UDMA/133 Apr 2 16:51:36 dell580 kernel: [ 28.945464] ata2: EH complete Apr 2 16:51:38 dell580 kernel: [ 31.581756] eth0: no IPv6 routers present Apr 2 16:51:38 dell580 kernel: [ 32.103066] ata2.01: exception Emask 0x40 SAct 0x0 SErr 0x80800 action 0x0 Apr 2 16:51:38 dell580 kernel: [ 32.103074] ata2.01: SError: { HostInt 10B8B } Apr 2 16:51:38 dell580 kernel: [ 32.103085] ata2.00: hard resetting link Apr 2 16:51:38 dell580 kernel: [ 32.419669] ata2.01: hard resetting link Apr 2 16:51:39 dell580 kernel: [ 32.894518] ata2.00: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.894533] ata2.01: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 2 16:51:39 dell580 kernel: [ 32.926536] ata2.00: configured for UDMA/100 Apr 2 16:51:39 dell580 kernel: [ 32.934715] ata2.01: configured for UDMA/133 Apr 2 16:51:39 dell580 kernel: [ 32.935578] ata2: EH complete Here's the output of smartctl for the drive. smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-17-generic] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: SAMSUNG SpinPoint F1 DT Device Model: SAMSUNG HD103UJ Serial Number: S13PJ90QC19706 LU WWN Device Id: 5 0000f0 00b1c7960 Firmware Version: 1AA01113 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 3b Local Time is: Mon Apr 2 17:13:48 2012 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 41) The self-test routine was interrupted by the host with a hard or soft reset. Total time to complete Offline data collection: (11772) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 197) minutes. Conveyance self-test routine recommended polling time: ( 21) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 076 076 011 Pre-fail Always - 7940 4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 521 5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 100 100 015 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 642 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 11 Calibration_Retry_Count 0x0012 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 482 13 Read_Soft_Error_Rate 0x000e 100 100 000 Old_age Always - 0 183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 759 184 End-to-End_Error 0x0033 100 100 000 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 073 069 000 Old_age Always - 27 (Min/Max 16/27) 194 Temperature_Celsius 0x0022 073 067 000 Old_age Always - 27 (Min/Max 16/28) 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 320028 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 099 099 000 Old_age Always - 1494 200 Multi_Zone_Error_Rate 0x000a 100 100 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 211 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 211 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 0f 31 63 8f e1 Error: ICRC, ABRT 15 sectors at LBA = 0x018f6331 = 26174257 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 40 62 8f e1 08 00:01:00.460 READ DMA c8 00 20 00 7c 30 e0 08 00:01:00.450 READ DMA c8 00 00 10 49 8f e1 08 00:01:00.440 READ DMA c8 00 e0 20 d0 30 e0 08 00:01:00.420 READ DMA c8 00 00 c0 59 90 e1 08 00:01:00.400 READ DMA Error 210 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 cf e9 cf 66 e0 Error: ICRC, ABRT 207 sectors at LBA = 0x0066cfe9 = 6737897 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 b8 cf 66 e0 08 00:08:29.780 READ DMA c8 00 60 60 c9 18 e0 08 00:08:29.770 READ DMA c8 00 40 20 c9 18 e0 08 00:08:29.770 READ DMA c8 00 20 00 c9 18 e0 08 00:08:29.760 READ DMA c8 00 20 98 cf 66 e0 08 00:08:29.750 READ DMA Error 209 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 2f d1 74 e0 e0 Error: ICRC, ABRT 47 sectors at LBA = 0x00e074d1 = 14709969 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 00 00 74 e0 e0 08 00:00:30.940 READ DMA c8 00 20 18 36 de e0 08 00:00:30.930 READ DMA c8 00 08 48 f1 dd e0 08 00:00:30.930 READ DMA c8 00 08 a8 f0 dd e0 08 00:00:30.930 READ DMA c8 00 08 90 f0 dd e0 08 00:00:30.930 READ DMA Error 208 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 7f 21 88 9d e0 Error: ICRC, ABRT 127 sectors at LBA = 0x009d8821 = 10324001 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 a0 00 88 9d e0 08 00:00:27.610 READ DMA c8 00 58 a8 e7 9c e0 08 00:00:27.610 READ DMA c8 00 00 28 e6 9c e0 08 00:00:27.610 READ DMA c8 00 00 e0 e4 9c e0 08 00:00:27.610 READ DMA c8 00 00 90 e0 9c e0 08 00:00:27.600 READ DMA Error 207 occurred at disk power-on lifetime: 0 hours (0 days + 0 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 26 6a 6a c3 e0 Error: ABRT at LBA = 0x00c36a6a = 12806762 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 00 90 69 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 68 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 50 65 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 d0 64 c3 e0 08 00:29:39.350 WRITE DMA ca 00 40 90 63 c3 e0 08 00:29:39.350 WRITE DMA SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Interrupted (host reset) 90% 638 - # 2 Short offline Interrupted (host reset) 90% 638 - # 3 Extended offline Interrupted (host reset) 90% 638 - # 4 Short offline Interrupted (host reset) 90% 638 - # 5 Extended offline Interrupted (host reset) 90% 638 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

  Read the article

• WCF Versioning, Naming and Endpoint URL

  - by Vinothkumar VJ

  I have a WCF Service and a Main Lib1. Say, I have a Save Profile Service. WCF gets data (with predefined data contract) from client and pass the same to the Main Class Lib1, generate response and send it back to client. WCF Method : SaveProfile(ProfileDTO profile) Current Version 1.0 ProfileDTO have the following UserName Password FirstName DOB (In string yyyy-mm-dd) CreatedDate (In string yyyy-mm-dd) Next Version (V2.0) ProfileDTO have the following UserName Password FirstName DOB (In UnixTimeStamp) CreatedDate (In UnixTimeStamp) Version 3.0 ProfileDTO have the following (With change in UserName and Password length validation) UserName Password FirstName DOB (In UnixTimeStamp) CreatedDate (In UnixTimeStamp) In simple we have DataContract and Workflow change between each version 1. How do I name the methods in WCF Service and Main Class Lib1? 2. Do I have to go with any specific pattern for ease development and maintenance? 3. Do I have to have different endpoints for different version? In the above example I have a method named “SaveProfile”. Do I have to name the methods like “SaveProfile1.0”, “SaveProfile2.0”, etc. If that is the case when there is no change between Version “3.0” and “4.0” then there will difficult in maintenance. I’m looking for a approach that will help in ease maintenance

  Read the article

• Given a database table where multiple rows have the same values and only the most recent record is to be returned

  - by Jim Lahman

  I have a table where there are multiple records with the same value but varying creation dates.  A sample of the database columns is shown here:   1: select lot_num, to_char(creation_dts,'DD-MON-YYYY HH24:MI:SS') as creation_date 2: from coil_setup 3: order by lot_num   LOT_NUM                        CREATION_DATE        ------------------------------ -------------------- 1435718.002                    24-NOV-2010 11:45:54 1440026.002                    17-NOV-2010 06:50:16 1440026.002                    08-NOV-2010 23:28:24 1526564.002                    01-DEC-2010 13:14:04 1526564.002                    08-NOV-2010 22:39:01 1526564.002                    01-NOV-2010 17:04:30 1605920.003                    29-DEC-2010 10:01:24 1945352.003                    14-DEC-2010 01:50:37 1945352.003                    09-DEC-2010 04:44:22 1952718.002                    25-OCT-2010 09:33:19 1953866.002                    20-OCT-2010 18:38:31 1953866.002                    18-OCT-2010 16:15:25   Notice that there are multiple instances of of the same lot number as shown in bold. To only return the most recent instance, issue this SQL statement: 1: select lot_num, to_char(creation_date,'DD-MON-YYYY HH24:MI:SS') as creation_date 2: from 3: ( 4: select rownum r, lot_num, max(creation_dts) as creation_date 5: from coil_setup group by rownum, lot_num 6: order by lot_num 7: ) 8: where r < 100  LOT_NUM                        CREATION_DATE        ------------------------------ -------------------- 2019416.002                    01-JUL-2010 00:01:24 2022336.003                    06-OCT-2010 15:25:01 2067230.002                    01-JUL-2010 00:36:48 2093114.003                    02-JUL-2010 20:10:51 2093982.002                    02-JUL-2010 14:46:11 2093984.002                    02-JUL-2010 14:43:18 2094466.003                    02-JUL-2010 20:04:48 2101074.003                    11-JUL-2010 09:02:16 2103746.002                    02-JUL-2010 15:07:48 2103758.003                    11-JUL-2010 09:02:13 2104636.002                    02-JUL-2010 15:11:25 2106688.003                    02-JUL-2010 13:55:27 2106882.003                    02-JUL-2010 13:48:47 2107258.002                    02-JUL-2010 12:59:48 2109372.003                    02-JUL-2010 20:49:12 2110182.003                    02-JUL-2010 19:59:19 2110184.003                    02-JUL-2010 20:01:03

  Read the article

• Be aware of the difference between CURRENT_DATE and SYSDATE

  - by Kevin Smith

  I was running some queries in SQL Developer against the WebCenter Content (WCC) schema that included date fields such as dInDate. I was comparing the dates against CURRENT_DATE. I was not getting the expected results. I did some googlng and didn’t find a solution, but I did run across a reference to SYSDATE. I tried SYSDATE in my queries and got the expected results. I did a TO_CHAR on the two date fields and found they returned different times. CURRENT_DATE returned the time from my laptop which was  in the EDT time zone. SYSDATE returned the time from the database server which happened to be in the PDT time zone. I guess if both the database server and my laptop were in the same time zone I would not have seen any problem. Here is the query I ran to display the two fields. select to_char(current_date,'DD-MON-YY HH:MI:SS'), to_char(sysdate,'DD-MON-YY HH:MI:SS') from dual; As you can see from the screen shot from SQL Developer they definitely returned different times. I’m sure there is some command or setting you can use to prevent this problem, but for me the take away is to use SYSDATE in your queries when you want to do any date comparison.

  Read the article

• Having issues using fdisk and GParted with Lexar 64GB USB, but reading and writing is fine

  - by MetaDark

  I have recently bought a new 64GB Lexar USB with the long model name of LJDV10-64G-000-106, and I am having issues partitioning it. I am able to mount, read and write to the USB without any issues but whenever I try to partition it with GParted it doesn't show up in the dropdown. Also while using the command sudo fdisk -l I receive the error fdisk: unable to seek on /dev/sdc: Invalid argument. This is a brand new USB so I am not sure why I am having these issues, especially since the device is functioning perfectly with read/write. I have tried reformatting it on a windows machine but that does not seem to do anything. For those who want a visual my USB looks almost exactly like But 64GB rather than 8GB Edit: I have just ran GParted from the terminal and I am getting a similar error, but it may give more information on the issue. Could not determine physical sector size for /dev/sdc. Using the logical sector size (512). Invalid argument during seek for read on /dev/sdc Also clearing my USB with /dev/zero fails with the the message $ sudo dd if=/dev/zero of=/dev/sdc bs=1M dd: writing `/dev/sdc': No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00167254 s, 0.0 kB/s

  Read the article

• Setting jQuery after ASP.net AJAX partial post back

  - by Steve Clements

  OK, so for some reason you have a mega mashup solution with ASP.net AJAX, jQuery and web forms.  Perhaps you are just on the migration from AjaxControlToolkit to the jQuery UI framework – who knows!! Anyway, the problem is that when you post back with something like an UpdatePanel, you will find that your nicely setup jQuery stuff, like the datepicker for example will no longer work. You may have something like this… $(document).ready(function () {     $(".date-edit").datepicker({ dateFormat: "dd/mm/yy", firstDay: 1, showOtherMonths: true, selectOtherMonths: true }); });   When you’re ASP.net UpdatePanel post back, you will find that your datepicker has gone.  Bugger! Well you need to add this little gem to set it back up again once the UpdatePanel comes back to the page. var prm = Sys.WebForms.PageRequestManager.getInstance(); prm.add_endRequest(function () {     $(".date-edit").datepicker({ dateFormat: "dd/mm/yy", firstDay: 1, showOtherMonths: true, selectOtherMonths: true }); });   Or like me, you would have a javascript function, something like InitPage(); do all your work in there and call that on document.ready and endRequest. Your choice…you have the power   Share this post :

  Read the article

• How to make and restore incremental snapshots of hard disk

  - by brunopereira81

  I use Virtual Box a lot for distro / applications testing purposes. One of the features I simply love about it is virtual machines snapshots, its saves a state of a virtual machine and is able to restore it to its former glory if something you did went wrong without any problems and without consuming your all hard disk space. On my live systems I know how to create a 1:1 image of the file system but all the solutions I'v known will create a new image of the complete file system. Are there any programs / file systems that are capable of taking a snapshot of a current file system, save it on another location but instead of making a complete new image it creates incremental backups? To easy describe what I want, it should be as dd images of a file system, but instead of only a full backup it would also create incremental. I am not looking for clonezilla, etc. It should run within the system itself with no (or almost none) intervention from the user, but contain all the data of the file systems. I am also not looking for a duplicity backup your all system excluding some folders script + dd to save your mbr. I can do that myself, looking for extra finesse. I'm looking for something I can do before doing massive changes to a system and then if something when wrong or I burned my hard disk after spilling coffee on it I can just boot from a liveCD and restore a working snapshot to a hard disk. It does not need to be daily, it doesn't even need a schedule. Just run once in a while and let it its job and preferably RAW based not file copy based.

  Read the article

• unreachable subnet in one direction

  - by Carl Michaud

  I'm unable to route traffic to a subnet in my home. Here's my topology: INET <- Router A <- Router B <- WIFI AP where: Router A - ARRIS TG862G/CT (from comcast) - WAN DHCP, LAN 10.0.0.99 Router B - Linksys WRT400N with DD-WRT - WAN 10.0.0.12 , LAN 10.0.1.1 I was able to use DD-WRT to configure a static route for the 10.0.1.x network back to the 10.0.0.x network. But I'm not sure if i can do the reverse on the ARRIS router and was looking for suggestions on how to fix that. I've set things up this wasy because I am using OpenDNS to mange internet content for my kids and of course I wasn't able to configure DNS to my liking on Router A either. So at present I'm using Router A on 10.0.0.x to provide a private unfiltered WIFI AP (no ssid broadcast) that I use for netflix only and then I use router B to provide a filtered WIFI AP for the rest of my WIFI devices on 10.0.1.x. However I would like to be able to connect to my 10.0.1.x devices from the internet via dynamic dns; but I can't see anything behind router B this way. Thoughts?

  Read the article

< Previous Page | 22 23 24 25 26 27 28 29 30 31 32 33  | Next Page >