Search Results

Search found 19703 results on 789 pages for 'virtual ip'.

Page 261/789 | < Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >

  • XP Mode as a server, Win 7 as a client

    - by Spyro
    I have two virtual machines (XP Mode). They are connected to each other by a network setting - Internal Network. It is the only working setting. This is the only way I got two virtual XP to ping each other. Now I want to connect each of them from the application that runs on Windows 7 which is hosting both virtual machines, but I can't do that. The firewall on both XP-Mode machines is disabled. Any other networking setting added as additional adapter on Xp-Mode machine does not allow me to connect from Windows 7. So my question is this - how to enable connection from Windows 7 application to XP mode application (client - server)? Point 2 (pass message) work perfectly because of the "internal network" setting. The problem is point 1 and 3.

    Read the article

  • How does Windows Remote Desktop Connection Work?

    - by Devoted
    How does Windows Remote Desktop connection work? An IP address is used to connect to the computer but....how can that IP be accessed from anywhere? If, for example, the IP address is 128.10.10.10, there MUST be another 128.10.10.10 somewhere else in the world. How does Remote Desktop know which one to connect to? Thanks so much EDIT: Thank you! Answers cleared this up quite a bit. But if my remote desktop connection suddenly stopped working and I didn't change anything, how do I even start to diagnose what may be the problem? I can remote connect to it from a LAN computer though...

    Read the article

  • Can't connect to VPN in Windows XP mode

    - by darkstar13
    I have Windows 7 x32 installed on my laptop. I have also Windows XP mode installed. My setup is that my work-remote programs are in Windows XP mode because my VPN installer in Windows XP only. Lately, I have been having troubles getting on / logging in to VPN. I can access the internet in WinXP mode but When I ping the IP address of the target IP of my VPN network (or even just Google.com), I always get a 'Request Timeout'. However, when I ping the same IP address in command prompt in Windows 7, I get 100% data sent. Is there anything I need to adjust? Before, I have been able to connect instantly. Now, it's like trial and error, or I will have to wait for hours just to be able to enter logon credentials in Cisco VPN dialer. NAT is my network adapter in XP mode.

    Read the article

  • How do I delete a route in OS X 10.5

    - by authormichael-olsen-craig
    I somehow configured my Mac to route all requests for a particular IP Name (sample.com) to the loopback address (127.0.0.1). Now I'm trying to remove this, but can't determine where to do it. There is no entry for it under /etc/hosts. The routing table shows that it is mapping the IP Name to the IP address of the Mac. Routing table output below: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.2.1 UGSc 4 1 en0 127 sample.com UCS 0 0 lo0 sample.com sample.com UH 1 7093 lo0 169.254 link#4 UCS 0 0 en0 192.168.2 link#4 UCS 6 0 en0 192.168.2.1 0:11:22:22:3f:fa UHLW 20 55565 en0 1070 192.168.2.15 tsema.org UHS 0 9 lo0 192.168.2.255 link#4 UHLWb 4 84777 en0 Any help would be greatly appreciated!

    Read the article

  • Resize Ubuntu Linux system to smaller disk inside VMware ESXi

    - by mlambie
    I have several Ubuntu Linux virtual machines running on VMware ESXi hosts that have all been allocated disks much larger than their required capacity. As space is now becoming an issue on our SAN, I'd like to investigate downsizing the allocated disk space on these machines. All systems will be completely backed up imaged before I begin making changes, and I will always retain a pristine backup in case the partition resizing does not work. Is there an easier way than the following procedure, or is their a better solution entirely? Shutdown and assign a second disk to the virtual machine Boot using the SystemRescueCD Use GParted to resize the original (source) partition, making it smaller Clone the new, smaller partition to the second disk Shutdown and remove initial disk from the virtual machine Reboot and force fsck to check the filesystem

    Read the article

  • Cross-platform, human-readable, du on root partition that truly ignores other filesystems

    - by nice_line
    I hate this so much: Linux builtsowell 2.6.18-274.7.1.el5 #1 SMP Mon Oct 17 11:57:14 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux df -kh Filesystem Size Used Avail Use% Mounted on /dev/mapper/mpath0p2 8.8G 8.7G 90M 99% / /dev/mapper/mpath0p6 2.0G 37M 1.9G 2% /tmp /dev/mapper/mpath0p3 5.9G 670M 4.9G 12% /var /dev/mapper/mpath0p1 494M 86M 384M 19% /boot /dev/mapper/mpath0p7 7.3G 187M 6.7G 3% /home tmpfs 48G 6.2G 42G 14% /dev/shm /dev/mapper/o10g.bin 25G 7.4G 17G 32% /app/SIP/logs /dev/mapper/o11g.bin 25G 11G 14G 43% /o11g tmpfs 4.0K 0 4.0K 0% /dev/vx lunmonster1q:/vol/oradb_backup/epmxs1q1 686G 507G 180G 74% /rpmqa/backup lunmonster1q:/vol/oradb_redo/bisxs1q1 4.0G 1.6G 2.5G 38% /bisxs1q/rdoctl1 lunmonster1q:/vol/oradb_backup/bisxs1q1 686G 507G 180G 74% /bisxs1q/backup lunmonster1q:/vol/oradb_exp/bisxs1q1 2.0T 1.1T 984G 52% /bisxs1q/exp lunmonster2q:/vol/oradb_home/bisxs1q1 10G 174M 9.9G 2% /bisxs1q/home lunmonster2q:/vol/oradb_data/bisxs1q1 52G 5.2G 47G 10% /bisxs1q/oradata lunmonster1q:/vol/oradb_redo/bisxs1q2 4.0G 1.6G 2.5G 38% /bisxs1q/rdoctl2 ip-address1:/vol/oradb_home/cspxs1q1 10G 184M 9.9G 2% /cspxs1q/home ip-address2:/vol/oradb_backup/cspxs1q1 674G 314G 360G 47% /cspxs1q/backup ip-address2:/vol/oradb_redo/cspxs1q1 4.0G 1.5G 2.6G 37% /cspxs1q/rdoctl1 ip-address2:/vol/oradb_exp/cspxs1q1 4.1T 1.5T 2.6T 37% /cspxs1q/exp ip-address2:/vol/oradb_redo/cspxs1q2 4.0G 1.5G 2.6G 37% /cspxs1q/rdoctl2 ip-address1:/vol/oradb_data/cspxs1q1 160G 23G 138G 15% /cspxs1q/oradata lunmonster1q:/vol/oradb_exp/epmxs1q1 2.0T 1.1T 984G 52% /epmxs1q/exp lunmonster2q:/vol/oradb_home/epmxs1q1 10G 80M 10G 1% /epmxs1q/home lunmonster2q:/vol/oradb_data/epmxs1q1 330G 249G 82G 76% /epmxs1q/oradata lunmonster1q:/vol/oradb_redo/epmxs1q2 5.0G 609M 4.5G 12% /epmxs1q/rdoctl2 lunmonster1q:/vol/oradb_redo/epmxs1q1 5.0G 609M 4.5G 12% /epmxs1q/rdoctl1 /dev/vx/dsk/slaxs1q/slaxs1q-vol1 183G 17G 157G 10% /slaxs1q/backup /dev/vx/dsk/slaxs1q/slaxs1q-vol4 173G 58G 106G 36% /slaxs1q/oradata /dev/vx/dsk/slaxs1q/slaxs1q-vol5 75G 952M 71G 2% /slaxs1q/exp /dev/vx/dsk/slaxs1q/slaxs1q-vol2 9.8G 381M 8.9G 5% /slaxs1q/home /dev/vx/dsk/slaxs1q/slaxs1q-vol6 4.0G 1.6G 2.2G 42% /slaxs1q/rdoctl1 /dev/vx/dsk/slaxs1q/slaxs1q-vol3 4.0G 1.6G 2.2G 42% /slaxs1q/rdoctl2 /dev/mapper/appoem 30G 1.3G 27G 5% /app/em Yet, I equally, if not quite a bit more, also hate this: SunOS solarious 5.10 Generic_147440-19 sun4u sparc SUNW,SPARC-Enterprise Filesystem size used avail capacity Mounted on kiddie001Q_rpool/ROOT/s10s_u8wos_08a 8G 7.7G 1.3G 96% / /devices 0K 0K 0K 0% /devices ctfs 0K 0K 0K 0% /system/contract proc 0K 0K 0K 0% /proc mnttab 0K 0K 0K 0% /etc/mnttab swap 15G 1.8M 15G 1% /etc/svc/volatile objfs 0K 0K 0K 0% /system/object sharefs 0K 0K 0K 0% /etc/dfs/sharetab fd 0K 0K 0K 0% /dev/fd kiddie001Q_rpool/ROOT/s10s_u8wos_08a/var 31G 8.3G 6.6G 56% /var swap 512M 4.6M 507M 1% /tmp swap 15G 88K 15G 1% /var/run swap 15G 0K 15G 0% /dev/vx/dmp swap 15G 0K 15G 0% /dev/vx/rdmp /dev/dsk/c3t4d4s0 3 20G 279G 41G 88% /fs_storage /dev/vx/dsk/oracle/ora10g-vol1 292G 214G 73G 75% /o10g /dev/vx/dsk/oec/oec-vol1 64G 33G 31G 52% /oec/runway /dev/vx/dsk/oracle/ora9i-vol1 64G 33G 31G 59% /o9i /dev/vx/dsk/home 23G 18G 4.7G 80% /export/home /dev/vx/dsk/dbwork/dbwork-vol1 292G 214G 73G 92% /db03/wk01 /dev/vx/dsk/oradg/ebusredovol 2.0G 475M 1.5G 24% /u21 /dev/vx/dsk/oradg/ebusbckupvol 200G 32G 166G 17% /u31 /dev/vx/dsk/oradg/ebuscrtlvol 2.0G 475M 1.5G 24% /u20 kiddie001Q_rpool 31G 97K 6.6G 1% /kiddie001Q_rpool monsterfiler002q:/vol/ebiz_patches_nfs/NSA0304 203G 173G 29G 86% /oracle/patches /dev/odm 0K 0K 0K 0% /dev/odm The people with the authority don't rotate logs or delete packages after install in my environment. Standards, remediation, cohesion...all fancy foreign words to me. ============== How am I supposed to deal with / filesystem full issues across multiple platforms that have a devastating number of mounts? On Red Hat el5, du -x apparently avoids traversal into other filesystems. While this may be so, it does not appear to do anything if run from the / directory. On Solaris 10, the equivalent flag is du -d, which apparently packs no surprises, allowing Sun to uphold its legacy of inconvenience effortlessly. (I'm hoping I've just been doing it wrong.) I offer up for sacrifice my Frankenstein's monster. Tell me how ugly it is. Tell me I should download forbidden 3rd party software. Tell me I should perform unauthorized coreutils updates, piecemeal, across 2000 systems, with no single sign-on, no authorized keys, and no network update capability. Then, please help me make this bastard better: pwd / du * | egrep -v "$(echo $(df | awk '{print $1 "\n" $5 "\n" $6}' | \ cut -d\/ -f2-5 | egrep -v "[0-9]|^$|Filesystem|Use|Available|Mounted|blocks|vol|swap")| \ sed 's/ /\|/g')" | egrep -v "proc|sys|media|selinux|dev|platform|system|tmp|tmpfs|mnt|kernel" | \ cut -d\/ -f1-2 | sort -k2 -k1,1nr | uniq -f1 | sort -k1,1n | cut -f2 | xargs du -shx | \ egrep "G|[5-9][0-9]M|[1-9][0-9][0-9]M" My biggest failure and regret is that it still requires a single character edit for Solaris: pwd / du * | egrep -v "$(echo $(df | awk '{print $1 "\n" $5 "\n" $6}' | \ cut -d\/ -f2-5 | egrep -v "[0-9]|^$|Filesystem|Use|Available|Mounted|blocks|vol|swap")| \ sed 's/ /\|/g')" | egrep -v "proc|sys|media|selinux|dev|platform|system|tmp|tmpfs|mnt|kernel" | \ cut -d\/ -f1-2 | sort -k2 -k1,1nr | uniq -f1 | sort -k1,1n | cut -f2 | xargs du -shd | \ egrep "G|[5-9][0-9]M|[1-9][0-9][0-9]M" This will exclude all non / filesystems in a du search from the / directory by basically munging an egrepped df from a second pipe-delimited egrep regex subshell exclusion that is naturally further excluded upon by a third egrep in what I would like to refer to as "the whale." The munge-fest frantically escalates into some xargs du recycling where -x/-d is actually useful, and a final, gratuitous egrep spits out a list of directories that almost feels like an accomplishment: Linux: 54M etc/gconf 61M opt/quest 77M opt 118M usr/ ##===\ 149M etc 154M root 303M lib/modules 313M usr/java ##====\ 331M lib 357M usr/lib64 ##=====\ 433M usr/lib ##========\ 1.1G usr/share ##=======\ 3.2G usr/local ##========\ 5.4G usr ##<=============Ascending order to parent 94M app/SIP ##<==\ 94M app ##<=======Were reported as 7gb and then corrected by second du with -x. Solaris: 63M etc 490M bb 570M root/cores.ric.20100415 1.7G oec/archive 1.1G root/packages 2.2G root 1.7G oec Guess what? It's really slow. Edit: Are there any bash one-liner heroes out there than can turn my bloated abomination into divine intervention, or at least something resembling gingerly copypasta?

    Read the article

  • Enable Hardware Virtualization on HP CompaqDX2420?

    - by 7alwagy
    Hey Guys, After installing vmware7, I tried to run a virtual machine with Mac OSX installed. When I tried to run this virtual machine I got an error message saying: Mac OS X is not supported with software virtualization. To run Mac OS X you need a host on which VMware Workstation supports hardware virtualization. I'v googled and found out that my processor (Intel Core 2 Duo E7500 Processor (2.93 GHz, 3 MB L2 cache, 1066 Mhz FSB)supports Hardware virtualization. Does anyone know how to enable this in order to get this virtual machine running?

    Read the article

  • XenServer VM's lose network settings

    - by Ash
    We deploy virtual machines using Citrix XenServer 6.0 for our clients. Two seperate clients experience the same issue: when a Server 2008 virtual machine is restarted, the static IP addresses (network address, subnet, gateway, primary DNS) don't appear to apply correctly as the IP's cannot be pinged, network services cannot be accessed etc. The issue is resolved by manually switching the network adapters to DHCP, then re-setting them to the original static IP's. While not a major issue, it's a pain when restarting servers due to Windows Updates, plus iSCSI drives need to be manually connected to Windows again via iSCSI Initiator. We have tried removed the network adapters from the virtual machine under XenCentre but without luck. Anyone experienced similar issues?

    Read the article

  • Netsh commands not working on remote computer

    - by Mike Christiansen
    Hello, At work, we are in the process of migrating over 200 computers from static IPs to DHCP. The DHCP server is configured. My biggest hurdle is physically going to every single computer in the area and configuring them all for DHCP. I am trying to use netsh to accomplish this. However, I cannot even seem to set one computer to DHCP remotely. The command I am trying is: netsh -r COMPUTERNAME interface ip set address name="Local Area Connection" source=dhcp netsh -r COMPUTERNAME interface ip set dns name="Local Area Connection" source=dhcp This results in the error The following command was not found: interface ip set address "name=Local Area Connection" source=dhcp. Any ideas?

    Read the article

  • Set up linux box for hosting a-z

    - by microchasm
    I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

    Read the article

  • High Availability Configuration using Heartbeat and Pacemaker

    - by pradeepchhetri
    I have the following setup: I have configured high availability between two load balancers (HAProxy) so that if HAProxy1 get down, the floating IP gets transferred to the other load balancer HAProxy2, hence all the clients will get the response from HAProxy2, which at the back-end is doing LB among the sme two webserver. This is for removing the single point of failure in case of only one HAProxy. Whenever I stops the hearbeat in HAProxy1, the floating IP goes to HAProxy2. But I want to configure such that whenever the process haproxy goes down, the floating IP should get assigned to HAProxy2. Can someone tell me how to implement it ?

    Read the article

  • How does Router know where to forward packet

    - by kornelijepetak
    If several computers with local addresses (192.168.0.#) are connected to a router and each computer opens a web browser and requests a page over HTTP, when these TCP:80 packets are sent out, the router switches the local address with the static IP of the router (i.e. Provider given IP) so the server can reply to the appropriate address. But how does the router know to which computer to forward the HTTP reply, since the TCP header does not contain the local IP address (does it?), and all computers are using port 80? Does this have anything to do with the MAC addresses? How exactly does this work?

    Read the article

  • Routing a PPTP client and VMware Server instance running on the same box

    - by servermanfail
    I have a Windows 2003 SBS box. It has 2 physical NIC's: WAN and LAN. The WAN is a public IP. The LAN is a simple 192.168.2.x subnet with Microsoft DHCP Server. Microsoft Routing and Remote Access Service is used to provide NAT to LAN. The box also runs VMware Server with a virtual machine running Windows XP. I want people to be able to VPN into the box, and connect to these virtual machines on the MSRDP port. I can VPN (PPTP) into the 2003 SBS box fine, as well as ping other machines on the LAN. I can ping the VM from a physical workstation on the LAN and vice-versa. I can ping the VPN client from the a physical workstation on the LAN and vice-versa. I can ping the VPN client from the Server console and vice-versa. I can ping the VM client from the Server console and vice-versa. But I cannot ping the VPN client from the VM and vice-versa. I was hoping to set up 2 or 3 Windows XP virtual machines on our only server, so that a couple of people can remote in to work without having to leave a physical machine on in the office. You could this attempted set up a "poor mans terminal server". On the 2003 SBS Server:- C:\Documents and Settings\Administrator>route print IPv4 Route Table =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...00 50 56 c0 00 08 ...... VMware Virtual Ethernet Adapter for VMnet8 0x3 ...00 50 56 c0 00 01 ...... VMware Virtual Ethernet Adapter for VMnet1 0x10004 ...00 53 45 00 00 00 ...... WAN (PPP/SLIP) Interface 0x10005 ...00 11 43 d4 69 13 ...... Broadcom NetXtreme Gigabit Ethernet 0x10006 ...00 11 43 d4 69 14 ...... Broadcom NetXtreme Gigabit Ethernet #2 =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 81.123.144.22 81.123.144.21 1 81.123.144.20 255.255.255.252 81.123.144.21 81.123.144.21 1 81.123.144.21 255.255.255.255 127.0.0.1 127.0.0.1 1 81.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 86.135.78.235 255.255.255.255 81.123.144.22 81.123.144.21 1 109.152.62.236 255.255.255.255 81.123.144.22 81.123.144.21 1 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.2.0 255.255.255.0 192.168.2.3 192.168.2.3 1 192.168.2.3 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.26 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.28 255.255.255.255 192.168.2.32 192.168.2.32 1 192.168.2.32 255.255.255.255 127.0.0.1 127.0.0.1 50 192.168.2.50 255.255.255.255 127.0.0.1 127.0.0.1 1 192.168.2.255 255.255.255.255 192.168.2.3 192.168.2.3 1 192.168.10.0 255.255.255.0 192.168.10.1 192.168.10.1 20 192.168.10.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.10.255 255.255.255.255 192.168.10.1 192.168.10.1 20 192.168.96.0 255.255.255.0 192.168.96.1 192.168.96.1 20 192.168.96.1 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.96.255 255.255.255.255 192.168.96.1 192.168.96.1 20 224.0.0.0 240.0.0.0 81.123.144.21 81.123.144.21 1 224.0.0.0 240.0.0.0 192.168.2.3 192.168.2.3 1 224.0.0.0 240.0.0.0 192.168.10.1 192.168.10.1 20 224.0.0.0 240.0.0.0 192.168.96.1 192.168.96.1 20 255.255.255.255 255.255.255.255 81.123.144.21 81.123.144.21 1 255.255.255.255 255.255.255.255 192.168.2.3 192.168.2.3 1 255.255.255.255 255.255.255.255 192.168.10.1 192.168.10.1 1 255.255.255.255 255.255.255.255 192.168.96.1 192.168.96.1 1 Default Gateway: 81.123.144.22 =========================================================================== Persistent Routes: None C:\Documents and Settings\Administrator>ipconfig /all Windows IP Configuration Host Name . . . . . . . . . . . . : 2003server Primary Dns Suffix . . . . . . . : mycompany.local Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : Yes WINS Proxy Enabled. . . . . . . . : Yes DNS Suffix Search List. . . . . . : mycompany.local gateway.2wire.net Ethernet adapter VMware Network Adapter VMnet8: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 8 Physical Address. . . . . . . . . : 00-50-56-C0-00-08 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.10.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : Ethernet adapter VMware Network Adapter VMnet1: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : VMware Virtual Ethernet Adapter for VMnet 1 Physical Address. . . . . . . . . : 00-50-56-C0-00-01 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.96.1 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : PPP adapter RAS Server (Dial In) Interface: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : WAN (PPP/SLIP) Interface Physical Address. . . . . . . . . : 00-53-45-00-00-00 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.32 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : NetBIOS over Tcpip. . . . . . . . : Disabled Ethernet adapter LAN: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet Physical Address. . . . . . . . . : 00-11-43-D4-69-13 DHCP Enabled. . . . . . . . . . . : No IP Address. . . . . . . . . . . . : 192.168.2.50 Subnet Mask . . . . . . . . . . . : 255.255.255.0 IP Address. . . . . . . . . . . . : 192.168.2.3 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : DNS Servers . . . . . . . . . . . : 192.168.2.3 Primary WINS Server . . . . . . . : 192.168.2.3 Ethernet adapter WAN: Connection-specific DNS Suffix . : gateway.2wire.net Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2 Physical Address. . . . . . . . . : 00-11-43-D4-69-14 DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 81.123.144.21 Subnet Mask . . . . . . . . . . . : 255.255.255.252 Default Gateway . . . . . . . . . : 81.123.144.22 DHCP Server . . . . . . . . . . . : 10.0.0.1 DNS Servers . . . . . . . . . . . : 10.0.0.1 Primary WINS Server . . . . . . . : 192.168.2.3 NetBIOS over Tcpip. . . . . . . . : Disabled Lease Obtained. . . . . . . . . . : 25 February 2011 22:56:59 Lease Expires . . . . . . . . . . : 25 February 2011 23:06:59 C:\Documents and Settings\Administrator>ping 192.168.2.11 Pinging 192.168.2.11 with 32 bytes of data: Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128 Reply from 192.168.2.11: bytes=32 time<1ms TTL=128

    Read the article

  • Does kern.hz still have any relevance in FreeBSD if "dynamic tick mode" is enabled?

    - by Frerich Raabe
    I'm running a FreeBSD 9.0 setup as a virtual machine in a KVM setup. In previous versions of FreeBSD it was common to force the kern.hz setting to a lower value so that the virtual machine does not keep the host busy because it's handling timer interrupts without having any work to do - the FreeBSD Handbook explains: The most important step is to reduce the kern.hz tunable to reduce the CPU utilization of FreeBSD under the Parallels environment. This is accomplished by adding the following line to /boot/loader.conf: kern.hz=100 Without this setting, an idle FreeBSD Parallels guest OS will use roughly 15% of the CPU of a single processor iMac®. After this change the usage will be closer to a mere 5%. However, in FreeBSD 9, the "dynamic tick mode" (aka "tickless mode") is the default, controlled by the kern.eventtimer.periodic setting which defaults to 0 (read: tickless mode). This makes me wonder - does the tip of lowering kern.hz still have any relevance for making FreeBSD 9 play nicely in a virtual machine setup?

    Read the article

  • Too many connectons to 212.192.255.240

    - by Castor
    Recently, my Internet slowed down drastically. I downloaded a tool to see the TCP/IP connections from my Vista computer. I found out that a lot TCP/IP connections are being connected to 212.192.255.240 through SVCHost. It seems that it is trying to connect to different ports. I think that my computer is being infected with some kind of malware etc. But I am not sure how to get rid of it. I did a little bit of research on this IP but found nothing. Any suggestions are highly apprecitated.

    Read the article

  • Belking Wireless Router unable to connect to internet although wireless connection is working

    - by ptamzz
    I have a Belkin Basic N150 Wireless router. I'm trying to set up wireless connection using the wired ports my university has provided in my hostel room. Usually, when I connect my laptop using a LAN wire through the port, my settings are like IP: 10.5.130.X Subnet Mask: 255.255.254.0 Default Gateway: 10.5.130.250 DNS Server: 10.200.1.11 and I'm able to connect to the internet. Now instead of connecting my laptop directly, I've connected the lan wire to the Belkin Wireless Router, set the router as "Use as an Access Point" and in the IP field, I've put up 10.5.130.1. Now I've set the IP of my system manually to 10.5.130.3. I'm able to connect to the wi-fi but I'm still not able to connect to the internet. What am I missing?

    Read the article

  • Access Bind9 DNS in Virtualbox on Host

    - by Philipp Melab
    I've set up a Ubuntu 10.04 Virtual Box with a Bind9 DNS server. The Box has a NAT Network connection for internet access and a host-only adapter for static ip connections from the host (OSX Lion). Thats the only way i managed to get internet and static ip inside the box, guess there is a better one ... The DNS works fine from inside the virtualbox, but not from the host. The http and ftp on the guest system is accessible via both addresses, so connection between host and guest are fine i guess. I tried to add both IP's as name servers. I'm completely new to Bind9 and DNS configuration. Anybody has a hint for me whats wrong? Or how i have to configure the DNS server?

    Read the article

  • IIS7 VPS Hosting Server Configuration

    - by Craig
    I have just registered a Windows 2008 VPS hosting account which I plan on running a couple of web sites on. In the past I have just used shared hosting in which everything is set up for me, so need a few pointers. When I register a new domain it asks for a couple of name servers. How do I set this up on my server? Can I just give it the IP address of the VPS server? Do I have to register some web sites with ns1, ns2 host headers in IIS? It's all a bit confusing when never done before. I have two web sites I plan on hosting. I configured both in IIS with a different IP address (the VPS plan has 2) but when trying to access the site via IP it always displays the default web site. If I turn off the default web site it just 404's. Is there any simple tutorials for setting up a couple of sites from scratch.

    Read the article

  • Minimum space required for Server 2008 R1 install?

    - by Chris J
    I'm trying to plan disk space for a virtual environment, and wanting to keep virtual disks as small as possible - mostly as apart from the base OS, the software going onto the VM is less than a few MB, so want to avoid physical disk space going to waste; plus it'll give me an idea of how many VMs I could physically fit in {x}GB of physical drive. For Server 2003, I've had installs on 2GB and 5GB sized virtual disks. However for Server 2008, Microsoft recommends a minimum of 10GB (I assume this is both for x32 and x64). For the record, I will be installing the x32 version. Now I know I could just go ahead and try a small install, but wanted to solicit any practical knowledge as well :-) What's the smallest install of Server 2008 possible? (excluding server core installations).

    Read the article

  • Is there a way to determine which service does an outgoing connection?

    - by fluxtendu
    I'm redoing my firewall configuration with more restrictive policies and I would like to determine the provenance (and/or destination) of some outgoing connections. I have an issue because they come from svchost.exe and go to web content/application delivery providers - or similar: 5 IP in range: 82.96.58.0 - 82.96.58.255 --> Akamai Technologies akamaitechnologies.com 3 IP in range: 93.150.110.0 - 93.158.111.255 --> Akamai Technologies akamaitechnologies.com 2 IP in range: 87.248.194.0 - 87.248.223.255 --> LLNW Europe 2 llnw.net 205.234.175.175 --> CacheNetworks, Inc. cachefly.net 188.121.36.239 --> Go Daddy Netherlands B.V. secureserver.net So is it possible to know which service does a particular connection? Or what's your recommendation about the rules applied to these ones? (Comodo Firewall & Windows 7)

    Read the article

  • Problem in listening to multicast in multihomed Linux server

    - by Lior
    I am trying to write a multicast client on a machine with two NICs, and I can't make it work. I can see with a sniffer that once I start the program the NIC (eth4) start receiving the multicast datagrams: y.y.y.y. (some ip) - z.z.z.z (multicast ip, not my eth4 NIC IP) UDP Source port: kkk (some other port) Destination port: xxx (multicast port) However, I can't get those packets using my program (listening to port xxx on eth4). I also added: route add 224.0.0.0 netmask 240.0.0.0 dev eth4 Searched the web for some examples/explanations, but it seems like I do what everybody else does. Any help will be appreciated. is there anything else to do with route/iptables?

    Read the article

  • How to configure 2nd network card for use in VMWare Workstation?

    - by Timo
    Hi all, I am using VMWare Workstation 6.5, connected to my network with a bridged adapter so that the virtual machine OS (Windows XP) has its own IP adress. This just worked out of the box. Now my host machine (Windows Vista) has an additional network card that is directly connected to another computer using a crossover cable (and fixed IP adress 10.1.1.4, while the "main" network connection is using DHCP with IP in the 192.68.0.* range). How can I use that network connection as well in the virtual machine? Do I need to bridge my 2nd network adapter to some VMnetX adapter? Do I need to add a host virtual adapter? I do not know much about networks, and the VMWare network settings really confuse me :-) Thanks, Timo

    Read the article

  • How to configure remote access to multiple subnets behind a SonicWALL NSA 2400

    - by Kyle Noland
    I have a client that uses a SonicWALL NSA 2400 as their firewall. I need to setup a second LAN subnet for a handful of PC. Management has decided that there should be a second subnet even though intend to allow access across the two subnets - I know... I'm having trouble getting communication across the 2 subnets. I can ping each gateway, but I cannot ping or seem to route traffic fron subnet A to subnet B. Here is my current setup: X0 Interface: LAN zone with IP addres 192.168.1.1 X1 Interface: WAN zone with WAN IP address X2 Interface: LAN zone with IP address 192.168.75.1 I have configured ARP and routes for the secondar subnet (X2) according to this SonicWALL KB article: http://www.sonicwall.com/downloads/supporting_multiple_firewalled_subnets_on_sonicos_enhanced.pdf using "Example 1". At this point I don't minding if I have to throw the SonicWALL GVC software VPN client into the mix to make it work. It feel like I have an Access Rule issue, but for testing I made LAN LAN, WAN LAN and VPN LAN rules wide open with the same results.

    Read the article

  • IPTables masquerading with one NIC

    - by Tuinslak
    Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

    Read the article

  • VPN, routing, specified application

    - by Adrian
    Details: eth0 = current internet port pptp1 = VPN connection, if I connect to my provider, he give me an IP address, which is accessible from the internet. This is what I need. I want to connect through this IP back to my PC. I want to keep my primary internet connection (eth0) on my PC for all traffic, but route traffic to VPN for specified application/or port, to access application/port from the IP, which I given from the pptp provider. Huhh? Difficult but, it is possible? If yes, how? Incoming port will be always: 33340 Outgoing port can be change, but usually it is 33330

    Read the article

< Previous Page | 257 258 259 260 261 262 263 264 265 266 267 268  | Next Page >