Search Results

Search found 8673 results on 347 pages for 'kvm switch'.

Page 265/347 | < Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >

• Two network adapters in one WindowsXP PC, how to make them work?

  - by Deele

  I have a need to set up network so I can use two ethernet cards inside one Windows (Windows XP SP2) based PC, one for internet connection, second, for internal LAN. How should I configure each NIC, with what IP's, subnet masks and gateways, so I can use inernet on my PC and get in touch with devices on my LAN? I have found that there are some sort of re routing nessesary inside my PC, but how does it work? I have already set up some configuration already, but I can't use it together with PC #1 NIC #1 connected. I need to disconnect, to access NIC WEB interface. Current configuration: Switch #1 and PC #1 NAS #2 are gigabit one's, so I could access NAS with gigabit speed. PC #1 NIC #1 IP XX.XXX.162.106 SN 255.255.255.248 GW XX.XXX.162.105 PC #1 NIC #2 IP 10.0.0.1 SN 255.255.0.0 GW 0.0.0.0 NAS #1 NIC #1 IP 10.0.0.12 SN 255.255.0.0 GW 0.0.0.0 My question is - what exact configuration should I do for every NIC in this LAN, so it would work? Is it possible to achieve internet access for Laptop, that is inside that NIC #2 LAN (should I just set up basic ICS)?

  Read the article

• Why is my rsync so slow?

  - by iblue

  My Laptop and my workstation are both connected to a Gigabit Switch. Both are running Linux. But when I copy files with rsync, it performs badly. I get about 22 MB/s. Shouldn't I theoretically get about 125 MB/s? What is the limiting factor here? EDIT: I conducted some experiments. Write performance on the laptop The laptop has a xfs filesystem with full disk encryption. It uses aes-cbc-essiv:sha256 cipher mode with 256 bits key length. Disk write performance is 58.8 MB/s. iblue@nerdpol:~$ LANG=C dd if=/dev/zero of=test.img bs=1M count=1024 1073741824 Bytes (1.1 GB) copied, 18.2735 s, 58.8 MB/s Read performance on the workstation The files I copied are on a software RAID-5 over 5 HDDs. On top of the raid is a lvm. The volume itself is encrypted with the same cipher. The workstation has a FX-8150 cpu that has a native AES-NI instruction set which speeds up encryption. Disk read performance is 256 MB/s (cache was cold). iblue@raven:/mnt/bytemachine/imgs$ dd if=backup-1333796266.tar.bz2 of=/dev/null bs=1M 10213172008 bytes (10 GB) copied, 39.8882 s, 256 MB/s Network performance I ran iperf between the two clients. Network performance is 939 Mbit/s iblue@raven $ iperf -c 94.135.XXX ------------------------------------------------------------ Client connecting to 94.135.XXX, TCP port 5001 TCP window size: 23.2 KByte (default) ------------------------------------------------------------ [ 3] local 94.135.XXX port 59385 connected with 94.135.YYY port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.09 GBytes 939 Mbits/sec

  Read the article

• What is the --daemon option?

  - by Pascal Dimassimo

  I was installing Solr with Jetty using these instructions. Basically, those instructions made you download the Jetty startup script and copy it to /etc/init.d/jetty. But it was not working. Each time I was starting Jetty, I had a "FAILED" message and nothing to understand why it was happening. I decided to open up the /etc/init.d/jetty script to understand what was happening. I saw that this script was using start-stop-daemon to launch jetty. After a couple of time of debugging, I discovered that removing the --daemon option at the end of the start-stop-daemon call was fixing my problem. I did a couple of research and discovered that this guy had the same problem and resolved it like I did: my removing the --daemon option. What is weird is that the switch does not seem to be specific to start-stop-daemon, because it is not documented in the man page. Also, I've seen it used for other commands. So what is that --daemon option doing? And why removing it resolved my problem? Note that I am working on Ubuntu 10.04.2 LTS.

  Read the article

• How do I setup routing for two companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: Two companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants its own Internet connection (ISP A) and company B wants its own Internet connection (ISP B). VLANs are deployed internally to separate the two companies' networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I set up policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• Siege - running a stress test benchmark

  - by morgoth84

  I need to do a benchmark test of a HTTPS server using Siege, to see how it behaves under massive load. I'm initiating tests from another machine which is quite powerful and it is connected to the same physical switch the server is connected on. But when I initiate a test, I can't get it to make more than 170 requests per second. With this load the server's CPU usage is at 15-20% and the average response time for a request is approx. 0.03 seconds. Load of the client machine is approx. at 10%. So, I gradually increase the number of users in Siege (the number of worker threads) and request rate linearly increases up to 170 reqs/sec, but it never gets over it. No matter how many more worker threads I start, the load on the server is never more than 20% (and the client's load also doesn't increase any more). How can I overcome this? I've googled a bit and found out that after a request is completed, a socket associated with one ephermal port remains in WAIT_TIME state for some time during which it can't be reused. I tried to overcome this by doing these things: sysctl -w net.ipv4.ip_local_port_range="1024 65535" echo 1 > /proc/sys/net/ipv4/tcp_tw_recycle Oh, and the client machine is a Linux (RedHat, I think, but I'm not sure). Any help would be appreciated.

  Read the article

• How to stop Vista from auto changing video resolution?

  - by bialix

  I have new Acer Aspire Revo R3600 computer with Vista pre-installed. The computer has NVidia video adapter. While connecting 17" LCD monitor (LG L1742S) via VGA cable it works fine, and I can change the resolution of the display from max 1920*1024 down to some other value, and after reboot the settings are restored correctly. But when I'm connecting bigger full HD 1920*1080 display (LG E2250) via VGA cable then every boot I have the same problem: I see boot progress window, then I see MS logo, then I see welcome screen then I start to see desktop and suddenly monitor switch off and show me the message about unsupported frequency of input signal As I understand Vista tries to auto-change resolution and sets wrong parameters. I've tried to boot into safe mode and into low-resolution mode, every time I have the same problem: Vista boot-up and suddenly monitor stops working. I've tried to connect this monitor to notebook with Windows XP and has no problem to work with this display on its native resolution. How can I disable this display resolution auto-changer in Vista? Or maybe there is another workaround?

  Read the article

• How does everyone set up AWS for PHP with a git workflow while worrying about distributing EC2?

  - by Parris

  Hello, I have been looking for something like heroku but for php, and after much frustration (and almost finding what I need, but not quite) we decided to just go with AWS without any other abstraction. We are using PHP 5.3 (and CakePHP 1.3), and are currently using git. Ubuntu seems like the easiest way to get both of those on there and we will most likely use that. We aren't really going worry about outgoing email. We are using smtp through gmail, but will most likely switch to some other service eventually. I had 3 questions: 1) I have been looking at Zend Server, and I am not quite sure how that is more beneficial than xampp. Perhaps it is not? 2) I suppose to make the application scale we would need multiple instances of some ec2 ami. Then just duplicate it and such. The question then becomes how do we make sure all EC2 instances are up to date? 3) I understand the concept of load balancing to some degree. I understand that in 1 region you select a bunch of servers and have it load balance across them. The question then becomes well how about world wide? How do I make it so that traffic is directed to the correct ec2 server? I have heard of route 53, and tried signing up for that, but nothing appears in my control panel. Also perhaps it is just a DNS thing with my domain registrar? AHHH... some tutorial would be helpful!

  Read the article

• Linux as a gateway (no NAT)

  - by Hugo

  I'm trying to configure a linux server as a gateway/router, but I can't get it to work, and all information I've managed to find is NAT-related. I have a public IP block for the gateway and devices behind it, so I want the gateway to simply route packets to the internet - again: no NATing! I've managed to get the gateway to access the internet successfully (that was just a matter of configuring the IP and GW), and the computers behind it can communicate with it. [EDIT: more info] This is actually an IPv6 block (2800:40:403::0/48) (but I've found that most utilities and instructions can be easily adapted from IPv4 to IPv6 with little hastle). The server has too ports: wan: 2800:40:403::1/48 lan: 2800:40:403::3/48 One of the computers behind it is connected to it via a switch; 2800:40:403::7/48 The wan interface on the server can ping6 www.google.com without issues. The lan interface on the server and the client can mutually ping each other without issues (as well as SSH, etc). I've tried setting the server as a default gateway for the client, with no luck: client # route -A inet6 add default gw 2800:40:403::3 dev eth1 server # cat /proc/sys/net/ipv6/conf/all/forwarding 1 I don't want any filtering/firewalling/etc, just plain routing. Thanks.

  Read the article

• Shortcuts that make using Windows easier? [closed]

  - by ekaj

  Over the years I have found out a good bit of shortcuts, all of which make using Windows that much faster and easier. I was wondering if I had missed any important ones, or ones that just saved any time. I tried to keep these relative to Windows only, as programs such as Mozilla, Photoshop, etc. bring in hundreds of other shortcuts, which do not apply to all users. These are the current ones I know: For the mouse: Scroll wheel - opens a link in IE into a new tab - closes a specific tab in IE when closed on Right click-n-drag - nifty menu to make a copy of a file or create a shortcut For the keyboard: Cntrl + Alt + Del - need this be explained? WinKey + R - opens 'Run..' WinKey + D - shows the desktop WinKey + E - opens 'My Computer' WinKey + F - opens 'Find..' WinKey + Tab - cool way to switch inbetween windows WinKey + L - locks the computer Alt + Tab - switches windows with a simple interface Alt + F4 - closes windows Alt + F - opens 'File' (Handy for things like IE if you have the menubar disabled) Cntrl + F - find text on current document Cntrl + W - closes a window, or current active tab in IE (or IE itself if only one tab) Cntrl + C - copies selected text / image Cntrl + V - pastes selected text / image So does anyone know of any more shortcuts that just make life easier? I would be much appreciative of any, and I am sure that some other users would like to know some too =]

  Read the article

• 4GB Memory Upgrade for Acer Aspire 5102WLMi

  - by Richard Slater

  I have bought a 4GB memory upgrade (2x 2GB PC2-5300 SODIMM) for my Acer Aspire 5102WLMi (Aspire 5100 Series) laptop, I installed the two memory modules correctly however with 4GB installed the laptop refuses to POST. I have tried the following: Tried both 2GB SODIMMs without the other (Worked Fine) Tried the original 512MB SODIMMs (Worked Fine) Tried with original 512MB SODIMM and new 2GB SODIMM (Worked Fine) Tried swapping over the 2GB SODIMs (Didn't Boot) Left the computer for 10 minutes with both 2GB SODIMMs installed (Didn't Boot) Checked latest BIOS installed (No Change) The Crucial website said that the laptop supported 4GB of RAM as do several other sites through found through Google, up until now I was fairly confident this would work. Couple of questions that would be good to have answered: Question: Has anyone got an Acer Aspire 5100 Series running with 4GB RAM? Answer: Yes, I have now got one working with 3.75GB Usable, the rest is occupied utilized by the Graphics Card. Question: Any tips on getting this to work; is there a CMOS reset switch? Answer: Yes there is, if both SODIMMs are removed two very small interlocking PCB tracks are revealed. If these are shorted together with a screwdriver the BIOS will be reset. Thanks.

  Read the article

• trying to setup multiple primary partitions on ubuntu linux [migrated]

  - by JohnMerlino

  I currently have ubuntu desktop installed on a harddrive. I want to partition the harddrive so that I can reserve 30 gigs for ubuntu server and 30 gigs for ubuntu desktop. The drive has 300 gigs available. Right now I am booting from dvd drive and installing ubuntu server. I selected "Guided partitioning" and created a 30 gig primary partition of Ext4 journaling filesystem, set "yes, format it" for format partition and set bootable flag to on. I intend to use this 30 gig partition to hold ubuntu server and allow me to boot from it. Now I have two other partitions. They are both set to "logical", one is currently using 285.8 gigs and is using ext4 (when I try to set bootable flag to true, it gives a warning "You are trying to set the bootable flag on a logical partition. The bootable flag is only useful on the primary partitions"). More alarming it says "No existing file system was detected in this partition". Actually, Im thinking that this is the parittion that is supposed to be holding my current Ubuntu Desktop. And of course I want this to be bootable and be a primary partition, so I could dual boot from this and the server partition. Now the third partition is also set to logical and it is being used as swap area. My question is regarding that second partition. Its supposed to be a primary partition thats holding my existing ubuntu desktop edition. How do I switch it to primary and to make sure that its pointing to my existing desktop installation?

  Read the article

• file read performance degrades as number of files increases

  - by bfallik-bamboom

  We're observing poor file read IO results that we'd like to better understand. We can use fio to write 100 files with a sustained aggregate throughput of ~700MB/s. When we switch the test to read instead of write, the aggregate throughput is only ~55MB/s. The drop seems related to the number of files since the throughput for read and write are comparable for a single file then diverge proportionally as we increase the number of files. The test server has 24 CPU cores, 48GB of memory, and is running CentOS 6.0. The disk hardware is a RAID 6 array with 12 disks and a Dell H800 controller. This device is partitioned with ext4 using the default settings. Increasing the readahead (using blockdev) improves the read throughput significantly but it still doesn't match write speed. For instance, increasing the readahead from 128KB to 1M improved the read throughput to ~145MB/s. Is this a known performance issue in our OS/disk/filesystem configuration? If so, how can we tell? If not, what tools or tests can we use to further isolate the issue? Thanks.

  Read the article

• Advice on cloning disk

  - by hks

  I'm going to buy a second disk for backup, the same size as my laptops. I want to mount it in a casing via usb and backup an entire hdd every soemtime. That's because I want the posibility to just switch drives in case of something goes wrong. I'm using Linux and obviously the right tool seems to be dd. The thing is that my laptop drive has a speed of around 50-70 MB/s and usb 2.0 is 57 MB/s. So to copy my 250GB disk should take me more than 1 hour if I'm lucky. I can't wait this much. I want some differential backup. I read one of JWZ articles. In it he gives more details for using rsync on Mac. He writes that there is possibility of making rsync'ed disk bootable. So my question is: how to make rsync'ed hdd bootable under Linux or are there other 'quick backup' tools for Linux that would allow me to just swap drives? Or should I just stick to dd :( ?

  Read the article

• Best way to patch (8) RJ45 ports from one room to another.

  - by zimmer62

  I have a 48 port patch panel in my basement, which I've wired almost all of them to various rooms around the house. Many are not actually being used at the moment, but pretty much all of them are wired to somewhere. As of recent, I've put in an HTPC in my media closet (different room), and I'm finding I need a lot more RJ45 plugs to this area. I have 4 drops here, and adding a switch will not solve my problems. I'm using the cabling for other things such as IR and Serial devices, not just Ethernet. What I'm hoping to do is add an 8 port panel in that media closet, and tie those into an 8 port panel on my rack next to the 48 port... What I don't want to do is pull 8 separate cables one by one from one area to the other unless someone has a technique that will allow me to do that quickly, and painlessly. Do they make cables with more conductors specifically for this purpose? Or patch panels that are designed for a special cable essentially just extending ports from one room to another?

  Read the article

• iptables (DNAT)

  - by user1126425

  I have a host that acts as a gateway for other hosts. The configuration is such that eth0(192.168.1.3) is connected to internet via a router and eth1(172.16.2.50) is connected to internal network via switch. Given that, this host is also running a service that is bound to eth1 and serves the internal network. I want to extend this service to the outside world as well and was trying to manipulate iptables so that any request that comes to this host via eth0 and is directed to 192.168.1.3:80 is send to 172.16.2.50 and internet users can also make use of the service. Here are my iptable rules for setting up the host as gateway (and these work fine): sudo iptables -t nat -A POSTROUTING -s 172.16.2.0/16 -o eth0 -j MASQUERADE sudo iptables -t nat -A POSTROUTING -s 192.168.1.0/24 -o eth1 -j MASQUERADE sudo iptables -A FORWARD -s 172.16.2.0/16 -o eth0 -j ACCEPT sudo iptables -A FORWARD -d 172.16.2.0/16 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT And these are the rules that I am trying to add to the iptables to achieve my ends: sudo iptables -A INPUT -d 192.168.1.3 -p tcp -dport 80 -i eth0 -j ACCEPT sudo iptables -t nat -A PREROUTING -d 192.168.1.3 -p tcp -dport 80 -j DNAT --to-destination 172.16.2.50:80 sudo iptables -t nat -A PREROUTING -s 172.16.2.50 -p tcp -sport 80 -j SNAT --to-source 192.168.1.3:80 sudo iptables -A FORWARD -d 192.168.1.3 -p tcp -dport 80 -m state --state ESTABLISHED,RELATED -j ACCEPT When I do so, I get error like : "multiple -d flags not allowed" ... Can someone tell me how to resolve this error... and do the entries that I want to add will serve my purpose ? Thanks!

  Read the article

• wireless clients not getting correct dhcp addresses

  - by szeli

  I apologise first if this is a stupid problem. I'm new to Cisco networking. I need some help with an existing configuration done by my vendor. Environment: 1. Core switch - Catalyst 6509e vlans configured: a. vlan 50 (wired clients) 10.0.50.x/24 interface IP 10.0.50.20 b. vlan 70 (wireless clients) 10.0.70.x/24 interface IP 10.0.70.20 c. vlan 192 (guest clients) 192.168.1.x/24 interface IP 192.168.1.20 d. trunk port for WLC native vlan 70 allowed vlan 50, 70, 192 2. Cisco 4402 WLC interfaces a. management untagged IP 10.0.70.10 b. ap-manager untagged IP 10.0.70.11 c. service-port n/a IP 192.168.10.1 d. virtual n/a IP 1.1.1.1 e. guestwlan vlan192 IP 192.168.1.100 3. Cisco AIR-LAP1142N-S-K9 LAP01 (WLAN local, interface: management) IP 10.0.70.21/24 GW 10.0.70.20 DHCP server 10.0.50.10 (scope 10.0.70.101 to 200) LAP02 (WLAN guest, interface: guestwlan) IP 192.168.1.21/24 GW 192.168.1.20 DHCP server 192.168.1.10 (scope 192.168.1.101 to 200) here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200) can anyone please help? thanks!

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Why is my browser using so much memory?

  - by Steve

  Hi. I've recently had problems with Firefox running very slowly when I have many tabs open; say 20 tabs. My whole system would slow down. I decided to give Google Chrome a try, and it started out fine. But lately I am finding that it too, slows down my whole system. Looking at Task Manager, chrome.exe is using about 250MB of memory in about 6 different entries in task manager. However, when I shut Chrome down, memory usage is reduced by about 600MB. How can this be? (shows drop in memory usage after ending Chrome.) When my system locks up with Chrome having many tabs open, it takes 10 seconds to load the Start Menu, 10 seconds to expand All Programs, and each folder and subfolder, and 30 seconds for the program to be highlighted under my mouse. It also takes 10 seconds to switch to Notepad. Why is Chrome appearing to use so much more memory than Task Manager indicates? Why is my pagefile being used when I have around 1.1GB of memory? Can I set Chrome to run in RAM and not in the pagefile? How can 20 tabs use 600MB? That's 30MB per tab. Thanks for your help.

  Read the article

• Bind9 not doing anything with forwarded query responses?

  - by Rykaro

  I have a Bind DNS server that is the local production DNS server and a Windows 2008 R2 domain controller which provides DNS for a lab environment with the domain xyz.lab. I've configured the Bind DNS to forward DNS requests for the domain xyz.lab to the Windows DNS server with this config: zone "xyz.lab" { type forward; forward only; forwarders { x.x.x.x; }; }; zone "x.x.x.in-addr.arpa" { type forward; forward only; forwarders { x.x.x.x; }; }; And Bind options are (the all_internal acl includes the subnets of both the production and lab networks as well as the loopback of the bind server): allow-query { all_internal; }; allow-recursion { all_internal; }; allow-transfer { none; }; notify no; minimal-responses yes; version "unknown"; Unfortunately, when I do an nslookup or dig on the bind server for a host on the lab domain, the request times out. The logs on the Windows 2008 DNS server show it receiving the query and responding to it and a network packet trace shows the query responses arriving at the Bind DNS server. The servers reside on the same switch with a router providing connectivity between the layer 3 subnets (production and lab are on different subnets) and there is a round trip time of between 3ms and 5ms on pings between the two servers, so I don't think there is an issue with latency causing a timeout of the query. In summary a query-response arrives back at the Bind server and the nslookup/dig times-out. Why does the Bind DNS not seem to be doing anything with the query responses when it receives them?

  Read the article

• Windows 8 Communication Sound Setting not working

  - by blackmastiff

  I've been having a problem on my new laptop recently which is familiar but baffling the usual fixes. I'm running Windows 8 with an onboard Realtek soundcard. It's similar to the one on my older computer running Windows 7. The problem is, when I'm in Skype or Mumble, Windows changes the sound output to lower everything else automatically. I've disabled the communications sound change option on the communications tab within sound devices and checked all the applications settings to insure that they are not responsible. They aren't, and I noticed something else. When I'm in the sound properties dialog, and I switch to the microphone tab, the same audio output reduction occurs. This seems to say to me that the microphone must be responsible in some way, but seeing as I uninstalled all the drivers and installed windows drivers instead, I'm confused as to why this would be occurring. Any thoughts? EDIT: I just tried disabling the built in microphone and the sound no longer get changed. More confused now? As soon as I turn it back on, the sound gets dropped again. Incidentally, the fix for this on windows 7 was this question: Windows 7 lowers applications' volume automatically I've got my computer set that way and it doesn't work.

  Read the article

• What could cause a dual-monitor PC to suddenly stop using one of the screens?

  - by raldi

  I've got a dual-monitor setup using a GeForce 7900GT that was working fine for over a year... then suddenly, only one of the screens works. It's not OS-related, because even on startup, only one screen displays the BIOS checks. In the past, both screens would show it together. I didn't change anything to trigger this The monitor that gets a signal is random -- sometimes the one on the left goes black, sometimes the one on the right. The monitors and their cables are good -- I can switch both or either, and I get a signal just fine. They're plugged in, too. It's not the video card, either -- I have an identical 7900GT in another machine, and swapping the two didn't fix anything. It's not dust on the motherboard -- I pulled everything out, cleaned it off, checked for obvious damage, put it all back together, and no change. My next two steps are going to be to reset the CMOS info and to try swapping out the motherboard. Before I do that, does anyone have any other ideas?

  Read the article

• Allied Telesis router: IP filtering for the LOCAL interface

  - by syneticon-dj

  Given an Allied Telesis router with an AlliedWare OS (2.9.1) I would like to disable access to all management services of the router except for a number of subnets (or alternatively have what is a "management VLAN" with other manufacturers' switch and router models). What I have tried so far: creating a new VLAN and an appropriate IP interface, setting the LOCAL IP into this subnet, creating an IP filter for the IP interface and specifying my exclusion subnets: it simply does not work as intended as I can access the LOCAL IP set from any of the other VLAN interfaces - the traffic is apparently not going through my defined filter set at all creating a new IP filter set and binding it to the LOCAL IP interface: this seems not to affect any kind of traffic at all, the counters for the filter set remain at zero packets setting the Remote Security Officer Level IP address range: this only restricts the ability for a user with the Security Officer privilege level to log in from any but the specified address ranges / subnets. Unfortunately, it does not prevent service availability (and thus DoS capacity) or the ability to log in as a less privileged user (e.g. a "manager") calling technical support: unfortunately no solution so far What I have not tried: creating a filter set for each and every IP interface defined on the router and excluding access to the router's management IP: I would like to reduce the overhead induced by IP filters as the router already is CPU-constrained at times. Setting up filters for every IP interface would mean that each and every traffic packet would have to pass the filters, thus consuming CPU cycles. If by any means possible, I would like to find a different solution.

  Read the article

• Identifying test machines in analytics logs

  - by RTigger

  We're just beginning to add analytics to our SaaS application, to begin (among other things) billing clients based on usage. The problem we're running into is there's a few circumstances where our support team will simulate a log in into production to try to reproduce reported issues with a client's configuration. When they log in, an entry will be made into our analytics logs that their specific account has logged in, which we use to calculate billing. A few ideas we had to solve this: 1) We log IP addresses as well as machine keys for each PC that logs in - we could filter out known IP addresses and/or machine keys belonging to support. The drawback is we have to maintain a list of keys / addresses manually. 2) If support (or anyone else internal) runs our application in debug mode (as opposed to release), it will not report analytics. This is fine, as long as support / anyone else remembers to switch to debug mode. 3) Include some sort of reg key / similar setting required to be set when configuring a production system in order to send analytics. Again, fine, as long as our infrastructure team remembers to set the reg key or setting. All of these approaches require some sort of human involvement, which we all know can be iffy at best. Has anyone run into a similar situation? Is there an automated approach to this problem? (PS Of course, we shouldn't be testing in production, but there are a few one-off instances with customer set up that we can't reproduce without logging in as them in production. This is the only time we do so, and this is the case I'm talking about in this question.)

  Read the article

• Graphics card ATI Asus 9250 128 MB AGP problem.Monitor switching off.

  - by Dominick1978

  I have an old system with these specs: Motherboard: Via P4x266a (with AGP 4x) CPU: P4 1,7 Ghz Memory: 1152 MB DDR SDRAM Graphics card: Voodoo 3 2000 16 MB PSU: 300 Watt It also has 1 dvd-rom, 1 dvd-rw, 2 hard drives (all 4 connected via molex) , 1 sounblaster sound card and 1 ethernet card (both connected via pci). OS: XP Pro Recently I bought Asus 9250 128 MB AGP to replace voodoo.Wnen I switch on the pc the initial screens (until after the xp logo) sometimes are distorted with blurred colours.When XP are loaded there is some flickering but the rest are ok.XP can't recognize the card seeing it as just a VGA adapter.I have downloaded the latest xp drivers from ATI website and installed them.Then after the restart everything is ok (no distorted image or blurring) until after the xp logo.After this the monitor turns off while the pc is still running.I have tried many drivers but the problem persists (of course I removed the voodoo drivers before from the display adapter properties).Only once I have managed to enter XP (after changing BIOS features for graphics card from 256 MB to 128 MB) but the drivers on the control panel had an exclamation mark (ati 9250!) and below them ati 9250 secondary without ! under the display adapter tab and the ATI catalyst program said that it couldn;t find the card.That was the opnly time I went beyond the xp logo.Now the monitor auto switcheS off. So, what do you think? 1)Is this a broken card? 2)Is it the drivers of the card? 3)Is it PSU fault? 4)Anything else? Thanks for your help and excuse my english!

  Read the article

• Configuring iPad Mail app & Gmail app with different accounts? [migrated]

  - by Steve Crane

  I prefer to use the Gmail app over the standard Mail app on my iPad for reading my personal Gmail (I delete a lot of mails, newsletters, etc., after reading and this is one tap in Gmail and several in Mail). I have them set up so my personal Gmail uses the Gmail app and my work email is set up to use the standard Mail app. This all works fine except for one problem. If I'm in Gmail or Mail and send an email it sends from the relevant email address as expected. My problem is that when I share something via email from Safari or another app it sends from the email address configured in Settings for Mail (the work one) and I would prefer to do such sharing from my personal email address. Does anyone know if there is a way to achieve this? I could switch the addresses to use the other app but as I never delete work email and delete personal mail at least 50% of the time, the behaviour of the apps is perfect the way I have them set up; if only I could solve that one little problem of controlling where shared items are sent from. I am using an iPad 2 with iOS 5.1 should that be relevant.

  Read the article

< Previous Page | 261 262 263 264 265 266 267 268 269 270 271 272  | Next Page >