Search Results

Search found 786 results on 32 pages for 'carpal tunnel'.

Page 27/32 | < Previous Page | 23 24 25 26 27 28 29 30 31 32  | Next Page >

• Cisco SR520w FE - WAN Port Stops Working

  - by Mike Hanley

  I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

  Read the article

• How to securely enable file sharing over PPTP on Windows 2008 Server

  - by Damage

  I have set up a Windows SBS 2003 domain (LAN) and a stand-alone Windows 2008 Server (web server) at another location (workgroup). I established PPTP VPN connection (SBS dials web server) over which users from LAN should be able to access web server. On web server I enabled TCP/IPv4 and File and Printer sharing protocol. It has a few external addresses (one of them is default) AND one local address (192.x.x.x) assigned to network adapter. Firewall allows port 445 for file sharing. There's the problem - I can not enable web server file shares to be visible to LAN users and ONLY to LAN users: From SBS I can access webserver but I cannot access webserver from LAN workstations (XP, Vista). I have had same configuration - I have just replaced old (web server) Windows 2003 server with 2008 so SBS settings are the same (static route, DNS etc.). How can I enable file sharing on web server for LAN workstations? Now I have opened File and printer sharing to the internet which is of course totaly unsecure. I tried to secure the tunnel so I moved RAS (VPN) connection (Network Center) on web server to "Private" profile and moved firewall port 445 to "Private" profile but suddenly file sharing does not work and I cannot telnet webserver on port 445. How can I secure file sharing so I do not have to open it to the internet?

  Read the article

• best practice to removing DC from Site that no longer connects via vpn in another city

  - by dasko

  hi i am looking for a recap of what i have done already to see if i missed anything. i had two cities connected by wan using a ipsec persistent tunnel between gateways. i had one DC (DOMAIN CONTROLLER) in each city that was a global catalog server (GC) they were set up to replicate and i had them configured under Sites and Servers with their own subnet etc... about 6 months ago the one city was removed and i was not able to gracefully remove, through dcpromo, the server that was there. it is no longer used and cannot be brought back. the company went from two sites down to single site. Problem is i had a whole bunch of kcc errors and replication bugs in the event viewer. i wanted to clean up my active directory and decided to use the ntdsutil metadata cleanup commands. i removed the server from the specifed site based on a procedure from petri website. I then removed the instances of the old DC and site from Sites and Servers. Then i went and cleaned up the DNS by removing Host A records, NS server name from both the local DNS forward lookup zone and the _msdcs i also removed the reverse lookup zone for the subnet that no longer exists. is there anything i missed? thanks in advance for any help. gd

  Read the article

• Configure IPv6 routing

  - by godlark

  I've got IPv6 addresses from SIXXS. My host is connected with SIXXS network over a AICCU tunnel ("sixxs" interface). My host address is 2001:::2, the host on the end has address 2001:::1. On my host IPv6 is fully accessible. I have problem with configuring IPv6 network on VMs. I use VirtualBox, the VM (Ubuntu) uses tap1 (on the host bridged by br0) #!/bin/sh PATH=/sbin:/usr/bin:/bin:/usr/bin:/usr/sbin # create a tap tunctl -t tap1 ip link set up dev tap1 # create the bridge brctl addbr br0 brctl addif br0 tap1 # set the IP address and routing ip link set up dev br0 ip -6 route del 2001:6a0:200:172::/64 dev sixxs ip -6 route add 2001:6a0:200:172::1 dev sixxs ip -6 addr add 2001:6a0:200:172::2/64 dev br0 ip -6 route add 2001:6a0:200:172::2/64 dev br0 Host: routing table: 2001:6a0:200:172::1 dev sixxs metric 1024 2001:6a0:200:172::/64 dev br0 proto kernel metric 256 2001:6a0:200:172::/64 dev br0 metric 1024 2000::/3 dev sixxs metric 1024 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev sixxs proto kernel metric 256 fe80::/64 dev br0 proto kernel metric 256 fe80::/64 dev tap1 proto kernel metric 256 default via 2001:6a0:200:172::1 dev sixxs metric 1024 Guest: interface eth1 (it is connected with tap1): auto eth1 iface eth1 inet6 static address 2001:6a0:200:172::3 netmask 64 gateway 2001:6a0:200:172::2 Guest: routing table 2001:6a0:200:172::/64 dev eth1 proto kernel metric 256 fe80::/64 dev eth0 proto kernel metric 256 fe80::/64 dev eth1 proto kernel metric 256 default via 2001:6a0:200:172::2 dev eth1 metric 1024 The guest pings to the host, the host pings to the guest, the host pings to 2001:6a0:200:172::1, but the guest doesn't ping to 2001:6a0:200:172::1. The guest tries to ping, on the host (by tcdump) I can capture its packets, but the host doesn't send them to 2001:6a0:200:172::1. What have I missed in configuration?

  Read the article

• Windows Server 2008 DHCP with RRAS

  - by Guillermo Prandi

  I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

  Read the article

• Snort/Barnyard2 Logging

  - by Eric

  I need some help with my Snort/Barnyard2 setup. My goal is to have Snort send unified2 logs to Barnyard2 and then have Barnyard2 send the data to other locations. Here is my currrent setup. OS Scientific Linux 6 Snort Version 2.9.2.3 Barnyard2 Version 2.1.9 Snort command snort -c /etc/snort/snort.conf -i eth2 & Barnyard2 command /usr/local/bin/barnyard2 -c /etc/snort/barnyard2.conf -d /var/log/snort -f snort.log -w /var/log/snort/barnyard.waldo & snort.conf output unified2: filename snort.log, limit 128 barnyard2.conf output alert_syslog: host=127.0.0.1 output database: log, mysql, user=snort dbname=snort password=password host=localhost With this setup, barnyard2 is showing all of the correct information in the database and I'm using BASE to view it on the web GUI. I was hoping to be able to send the full packet data to syslog with barnyard2 but after reading around, it seems that it is impossible to do that. So I then started trying to modify the snort.conf file and add lines like "output alert_full: alert.full". This definitely gave me a lot more information but still not the full packet data like I want. So my question is, is there anyway I can use barnyard2 to send the full packet data of alerts to a human readable file? Since I can't send it directly to syslog, I can create another process to take the data from that file and ship it off to another server. If not, what flags and/or snort.conf configuration would you recommend to get the most data possible but still be able to handle quite a bit of traffic? In the end of it all, these alerts will be shipped to a central server via a SSH tunnel. I'm trying to stay away from databases.

  Read the article

• Need a new mouse: clicky scroll wheel and additional thumb-operated scroll wheel

  - by cksubs

  I'm having some carpel tunnel syndrome or RSI issues, and I need to get a new mouse. I've tried a friend's Logitech MX Revolution and it's almost perfect. I LOVE the thumb-operated scroll wheel, and I think that that alone would solve many of my hand pain issues. The problem is that it uses their newfangled smooth/click scroll wheel. It can be either smooth or clicky, and is switched by pressing in the scroll wheel. I really question Logitech's user research on that one. I've been using middle-click to open new links and close tabs for years now in my browser, and I'm not willing to give that up for this cool technology. In fact I HATE smooth scroll wheels in general, and need a clicky one. The option would be ok, but not if it's activated via the middle-click button. In closing, I'm looking for these items in my mouse: Thumb-operated scroll wheel or 'joystick'-like apparatus. Clicky, as-stiff-as-possible scroll wheel on top Normal middle-click functionality. Comfortable, preferably ergonomic design. Anyone have any suggestions? Logitech, want to get rid of that smoothing-scrolling crap so I can buy your mouse?

  Read the article

• Fortinet: Is there any equivalent of the ASA's packet-tracer command?

  - by Kedare

  I would like to know if there is not Fortigates an equivalent of the packet-tracer command that we can find on the ASA. Here is an example of execution for those who don't know it: NAT and pass : lev5505# packet-tracer input inside tcp 192.168.3.20 9876 8.8.8.8 80 Phase: 1 Type: ACCESS-LIST Subtype: Result: ALLOW Config: Implicit Rule Additional Information: MAC Access list Phase: 2 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 3 Type: ACCESS-LIST Subtype: log Result: ALLOW Config: access-group inside-in in interface inside access-list inside-in extended permit tcp any any eq www access-list inside-in remark Allows DNS Additional Information: Phase: 4 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 5 Type: VPN Subtype: ipsec-tunnel-flow Result: ALLOW Config: Additional Information: Phase: 6 Type: NAT Subtype: Result: ALLOW Config: object network inside-network nat (inside,outside) dynamic interface Additional Information: Dynamic translate 192.168.3.20/9876 to 81.56.15.183/9876 Phase: 7 Type: IP-OPTIONS Subtype: Result: ALLOW Config: Additional Information: Phase: 8 Type: FLOW-CREATION Subtype: Result: ALLOW Config: Additional Information: New flow created with id 94755, packet dispatched to next module Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: allow Blocked by ACL: lev5505# packet-tracer input inside tcp 192.168.3.20 9876 8.8.8.8 81 Phase: 1 Type: ROUTE-LOOKUP Subtype: input Result: ALLOW Config: Additional Information: in 0.0.0.0 0.0.0.0 outside Phase: 2 Type: ACCESS-LIST Subtype: Result: DROP Config: Implicit Rule Additional Information: Result: input-interface: inside input-status: up input-line-status: up output-interface: outside output-status: up output-line-status: up Action: drop Drop-reason: (acl-drop) Flow is denied by configured rule Is there any equivalent on the Fortigates ?

  Read the article

• Why does nmap ping scan over a VPN link return all hosts alive?

  - by ewwhite

  I'm curious as to why running an nmap -sP (ping scan) on a remote subnet linked via a Cisco site-to-site IPSec tunnel returns "host up" status for every IP in the range. [root@xt ~]# nmap -sP 192.168.108.* Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-11-22 14:08 CST Host 192.168.108.0 appears to be up. Host 192.168.108.1 appears to be up. Host 192.168.108.2 appears to be up. Host 192.168.108.3 appears to be up. Host 192.168.108.4 appears to be up. Host 192.168.108.5 appears to be up. . . . Host 192.168.108.252 appears to be up. Host 192.168.108.253 appears to be up. Host 192.168.108.254 appears to be up. Host 192.168.108.255 appears to be up. Nmap finished: 256 IP addresses (256 hosts up) scanned in 14.830 seconds However, a ping of a known-down IP simply times out or doesn't return anything... [root@xt ~]# ping 192.168.108.201 PING 192.168.108.201 (192.168.108.201) 56(84) bytes of data. --- 192.168.108.201 ping statistics --- 144 packets transmitted, 0 received, 100% packet loss, time 143001ms Is there a more effective way to scan live devices connected in this manner?

  Read the article

• How to bypass firewall to connect to a proxy server?

  - by Bruce

  I am conducting a small experiment on my office network. I have setup a proxy server on my desktop machine (connected to my LAN) and I have volunteers access the internet via my proxy server. Everything is working well. The problem is people cannot connect to the proxy server through their laptops. I asked my network admin and he said the wireless network has a firewall which prevents users from connecting to my proxy. He said I could tunnel the traffic or use SSH though. I am afraid I do not understand fully what is going on. Is there a way by which users connected on the wireless network can connect to my desktop? I am using FreeProxy on Windows as my proxy server: http://www.handcraftedsoftware.org/index.php?page=download FreeProxy allows me to create a SOCKS 4/4a/5 proxy. Is that what I need? Part of the experiment involves logging the URL requests of the users. I am doing a measurement study. So, any solution must allow me to log the URL requests of users. Also, what changes do I need to make in the browser configuration.

  Read the article

• How to configuration keepalived on Amazon EC2?

  - by oeegee

  I rad some article. Keepalived over GRE tunnel for failover on VPS environment http://blog.killtheradio.net/how-tos/keepalived-haproxy-and-failover-on-the-cloud-or-any-vps-without-multicast/ but, I don't know how to configuration? and How to call this architecture? only I Know that How to config Master/Backup configuration at keepalived. What I want to know that How does work keepalived? I want to design this.... XMPP Server(EC2) | ------------------------------------------------- keepalived Master(EC2) - keepalived Backup(EC2) HAProxy #1 HAProxy#2 ------------------------------------------------- | Casandra#1 Casandra#2 Casandra#3 Casandra#4 Thanks! but What I want to know how to work on keepalived with unicast patche modul. ELB is expansive. and this is first totaly design. [Flow] ELB -- XMPP Server -- ELB -- Casandra ELB | XMPP#1 XMPP#2 XMPP#3 XMPP#4 | ELB | Casandra#1 Casandra#2 Casandra#3 Casandra#4 and change first design. [Flow] ELB -- XMPP Server -- HAProxy Master(Casandra Farm) -- Casandra ELB | XMPP#1 XMPP#2 XMPP#3 XMPP#4 | ------------------------------------------------- keepalived Master(EC2) - keepalived Backup(EC2) HAProxy#1 HAProxy#2 ------------------------------------------------- | Casandra#1 Casandra#2 Casandra#3 Casandra#4 this is second. [Flow] ELB -- HAProxy(XMPP Farm) -- XMPP Server -- HAProxy(Casandra Farm) -- Casanda It's OK? ELB | HAProxy#1 HAProxy#2 HAProxy#3 HAProxy#4 XMPP#1 XMPP#2 XMPP#3 XMPP#4 | Casandra#1 Casandra#2 Casandra#3 Casandra#4

  Read the article

• How to setup equivalent USVIDEO.ORG DNS-Proxy on Linux

  - by Gary

  I have a VPS in the USA running Ubuntu. I want to setup something similar to http://www.usvideo.org Basically, USVIDEO is a DNS service that allows Canadians to access American content like Hulu, Netflix, NBC, and etc (restricted by geographical IP). Here is how I think USVideo does it: Clients (PS3, XBOX, PC) specifies the DNS server(s) as specified on USVIDEO.org's website. If the DNS request is a video/audio site such as Netflix or Pandora, forward the request to a proxy. Otherwise, for all other requests, forward it to a different DNS server. If the specific video/audio URL is requested, return the address of the proxy server, which in turn relays traffic to the destination video/audio domain via the U.S. gateway so that it appears that the access is coming from a U.S. IP address. Once the DNS request has passed the U.S. IP address check, their proxy server steps out of the loop and lets the video streaming site contact you directly to start the video stream. This trick relies on the way that the video streaming sites check the country of your IP address once up front, but don't actually check the country of the destination IP address while the video is streaming. What is elegant about this solution is that a VPN Tunnel is not required to bypass geographical IP checks from certain websites. All that is required on the client side is to specify the DNS server (the VPS). If a certain site is geographically locked, just forward the traffic to a proxy, and that's it. These sites can be specified in the DNS entries, or perhaps in the proxy service to redirect the DNS request to its own proxy. I believe what I need to setup something similar is Squid Proxy, IPTables, and DNS. What I need help is how to exactly approach this? Would Squid Proxy be setup as a transparent proxy?

  Read the article

• DHCP not responding from laptop or router, but works on directly plugged PC?

  - by Matt H

  I'm at my sister in law's place in Singapore. I'm not from Singapore but am here for a few months. She has some sort of cable modem made by motorolla (SB5101 Surfboard). I think it goes, through starhub or similar provider. Anyhow, her PC is directly attached by cable (not wireless) and she can access the internet. There is no wireless router connected to it. The PC is configured with DHCP and appears to be working. However, the moment I unplug her PC and plug in my laptop, it doesn't get an address. The interesting thing here is that I also see this toredo tunnel adaptor etc. I'm not familiar with what that is. It appears to be being assigned an IP v6 address and an IP v4 address. I thought perhaps it's my laptop, but also when I plug in my DDWRT based router, it also fails to get a DHCP assigned address on the WAN port. I can't also seem to connect into any web configuration on the motorolla modem either. Any ideas? what kind of setup is this? all I'd like to do is plug in my wireless router so I can roam around the house and also access the internet.

  Read the article

• setting up a proxy to mirror an SSH SOCKS connection

  - by aresnick

  I have two remote machines, remote1 and remote2. remote2 is only running sshd, and I can't run anything else on it. remote1 is a full-fledged server to which I have complete access. I can run a SOCKS proxy on remote2 via ssh -f -N -D *:8080 me@remote2 which lets me expose a SOCKS proxy on port 8080 on remote1. I'd like to authenticate this so that the proxy isn't sitting open. How can I do this? It seems like I should be able to use delegate, but I can't even seem to get its HTTP proxy functionality working. When I run delegated -r -P8081 SERVER=http PERMIT="*:*:*" REMITTABLE="*" I can't even get it to work on port 8081. Anyway, I was hoping someone could point me in the right direction to let me authenticate access to the SOCKS proxy connection? That is, I want to be able to point my browser's proxy at remote1 and browse the internet through the SSH SOCKS proxy/tunnel to remote2. squid doesn't support a SOCKS parent =( Thanks!

  Read the article

• Cisco VPN endpoints disconnecting from a VLAN

  - by dunxd

  I have a number of Cisco ASA 5505 and PIX 506e around the world acting as VPN endpoints. They connect to a Cisco VPN Concentrator 3000 at HQ. I am using EZVPN to set up the VPN (i.e. most of the config is central on the VPN Concentrator) The majority of endpoints work absolutely fine. However, there are three that do not. 2 ASAs and 1 PIX get disconnected from one of the VLANs on our network. This is the VLAN that my monitoring server runs on - so those endpoints look as if they have gone down. However, I can still ping the endpoints from our user VLAN. If I then SSH onto the endpoint, and do a ping to my monitoring server, the connection comes back. Then after about 10 minutes it stops working again. I've looked at the configuration of my endpoints, and I can't see any significant differences. One common feature is that the affected endpoints are connecting to the internet via retail quality routers. However, I don't see how this could affect traffic within a VPN tunnel. Any ideas or suggestions? I've also got a thread on Cisco's forums at https://supportforums.cisco.com/thread/344638. One other person has reported the same problem.

  Read the article

• Why do I have 55 local area connections in ipconfig?

  - by RMorrisey

  Windows Vista Home Premium. I should mention that I am having no problem whatever getting an internet connection. When I type "ipconfig" in the console, I get (55!) messages of 3 lines each, listing a ton of disconnected network connections. My PC only has one network card. Each message looks like this: Tunnel adapter Local Area Connection* 55: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : These don't cause a major problem; they make it a pain, though, to fish upward and find my IP address. How can I get rid of them? Edit: Actually, a few connection numbers are randomly missing from the sequence; so, it's really more like 30 or 40 connection messages, rather than all 55. Not sure why that is, either.

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• Virtual Lan on the Cloud -- Help Confirm my understanding?

  - by marfarma

  [Note: Tried to post this over at ServerFault, but I don't have enough 'points' for more than one link. Powers that be, move this question over there.] Please give this a quick read and let me know if I'm missing something before I start trying to make this work. I'm not a systems admin professional, and I'd hate to end up banging my head into the wall if I can avoid it. Goals: Create a 'road-warrior' capable star shaped virtual LAN for consultants who spend the majority of their time on client sites, and who's firm has no physical network or servers. Enable CIFS access to a cloud-server based installation of Alfresco Allow Eventual implementation of some form of single-sign-on ( OpenLDAP server ) access to Alfresco and other server applications implemented in the future Given: All Servers will live in the public internet cloud (Rackspace Cloud Servers) OpenVPN Server will be a Linux disto, probably Ubuntu 9.x, installed on same server as Alfresco (at least to start) Staff will access server applications and resources from client sites, hotels, trains, planes, coffee shops or their homes over various ISP, using their company laptops or personal home desktops. Based on my Research thus far, to accomplish this, I'll need: OpenVPN with Bridging Enabled to create a star shaped "virtual" LAN http://openvpn.net/index.php/open-source/documentation/miscellaneous/76-ethernet-bridging.html A Road Warrior Network Configuration, as described in this Shorewall article (lower down the page) http://www.shorewall.net/OPENVPN.html Configure bridge addressesing (probably DHCP) http://openvpn.net/index.php/open-source/faq.html#bridge-addressing Configure CIFS / Samba to accept VPN IP address http://serverfault.com/questions/137933/howto-access-samba-share-over-vpn-tunnel Set up Client software, with keys configured for access (potentially through a OpenVPN-Sa client portal) http://www.openvpn.net/index.php/access-server/download-openvpn-as/221-installation-overview.html

  Read the article

• Changing Mac OS X 10.6 Routing after VPN'd In

  - by Matt Rogish

  I have a coffee shop around the corner that I use to do some work when I want to get away from home. They offer free wi-fi and I then use my Mac 10.6 VPN to log into my work network. I have "Send all traffic over VPN connection" checked. Before, their network was 10.0.0.x. I think they got a new router because it's now 192.168.2.x However, this interferes with one of the subnets at work so now I can't visit 192.168.2.x at work. So: 1) Office network: VPN gives IPs as 192.168.1.x. Another network is 192.168.2.x 2) Coffee network: Gives IPs as 192.168.2.x I think if I set a route to send all 2.x traffic over the tunnel, it would blow up my routing to their system, right? What should I do? I know the individual IPs of the servers I want... Maybe I could add each one, or can I add all of them minus the default gateway of their router? How do I set that up "temporarily" in my Mac? Thanks!!

  Read the article

• OpenVPN Client timing out

  - by Austin

  I recently installed OpenVPN on my Ubuntu VPS. Whenenver I try to connect to it, I can establish a connection just fine. However, everything I try to connect to times out. If I try to ping something, it will resolve the IP, but will time out after resolving the IP. (So DNS Server seems to be working correctly) My server.conf has this relevant information (At least I think it's relevant. I'm not sure if you need more or not) # Which local IP address should OpenVPN # listen on? (optional) ;local a.b.c.d # Which TCP/UDP port should OpenVPN listen on? # If you want to run multiple OpenVPN instances # on the same machine, use a different port # number for each one. You will need to # open up this port on your firewall. port 1194 # TCP or UDP server? ;proto tcp proto udp # "dev tun" will create a routed IP tunnel, # "dev tap" will create an ethernet tunnel. # Use "dev tap0" if you are ethernet bridging # and have precreated a tap0 virtual interface # and bridged it with your ethernet interface. # If you want to control access policies # over the VPN, you must create firewall # rules for the the TUN/TAP interface. # On non-Windows systems, you can give # an explicit unit number, such as tun0. # On Windows, use "dev-node" for this. # On most systems, the VPN will not function # unless you partially or fully disable # the firewall for the TUN/TAP interface. ;dev tap dev tun # Windows needs the TAP-Win32 adapter name # from the Network Connections panel if you # have more than one. On XP SP2 or higher, # you may need to selectively disable the # Windows firewall for the TAP adapter. # Non-Windows systems usually don't need this. ;dev-node MyTap # SSL/TLS root certificate (ca), certificate # (cert), and private key (key). Each client # and the server must have their own cert and # key file. The server and all clients will # use the same ca file. # # See the "easy-rsa" directory for a series # of scripts for generating RSA certificates # and private keys. Remember to use # a unique Common Name for the server # and each of the client certificates. # # Any X509 key management system can be used. # OpenVPN can also use a PKCS #12 formatted key file # (see "pkcs12" directive in man page). ca ca.crt cert server.crt key server.key # This file should be kept secret # Diffie hellman parameters. # Generate your own with: # openssl dhparam -out dh1024.pem 1024 # Substitute 2048 for 1024 if you are using # 2048 bit keys. dh dh1024.pem # Configure server mode and supply a VPN subnet # for OpenVPN to draw client addresses from. # The server will take 10.8.0.1 for itself, # the rest will be made available to clients. # Each client will be able to reach the server # on 10.8.0.1. Comment this line out if you are # ethernet bridging. See the man page for more info. server 10.8.0.0 255.255.255.0 # Maintain a record of client <-> virtual IP address # associations in this file. If OpenVPN goes down or # is restarted, reconnecting clients can be assigned # the same virtual IP address from the pool that was # previously assigned. ifconfig-pool-persist ipp.txt # Configure server mode for ethernet bridging. # You must first use your OS's bridging capability # to bridge the TAP interface with the ethernet # NIC interface. Then you must manually set the # IP/netmask on the bridge interface, here we # assume 10.8.0.4/255.255.255.0. Finally we # must set aside an IP range in this subnet # (start=10.8.0.50 end=10.8.0.100) to allocate # to connecting clients. Leave this line commented # out unless you are ethernet bridging. ;server-bridge 10.8.0.4 255.255.255.0 10.8.0.50 10.8.0.100 # Configure server mode for ethernet bridging # using a DHCP-proxy, where clients talk # to the OpenVPN server-side DHCP server # to receive their IP address allocation # and DNS server addresses. You must first use # your OS's bridging capability to bridge the TAP # interface with the ethernet NIC interface. # Note: this mode only works on clients (such as # Windows), where the client-side TAP adapter is # bound to a DHCP client. ;server-bridge # Push routes to the client to allow it # to reach other private subnets behind # the server. Remember that these # private subnets will also need # to know to route the OpenVPN client # address pool (10.8.0.0/255.255.255.0) # back to the OpenVPN server. ;push "route 192.168.10.0 255.255.255.0" ;push "route 192.168.20.0 255.255.255.0" # To assign specific IP addresses to specific # clients or if a connecting client has a private # subnet behind it that should also have VPN access, # use the subdirectory "ccd" for client-specific # configuration files (see man page for more info). # EXAMPLE: Suppose the client # having the certificate common name "Thelonious" # also has a small subnet behind his connecting # machine, such as 192.168.40.128/255.255.255.248. # First, uncomment out these lines: ;client-config-dir ccd ;route 192.168.40.128 255.255.255.248 # Then create a file ccd/Thelonious with this line: # iroute 192.168.40.128 255.255.255.248 # This will allow Thelonious' private subnet to # access the VPN. This example will only work # if you are routing, not bridging, i.e. you are # using "dev tun" and "server" directives. # EXAMPLE: Suppose you want to give # Thelonious a fixed VPN IP address of 10.9.0.1. # First uncomment out these lines: ;client-config-dir ccd ;route 10.9.0.0 255.255.255.252 # Then add this line to ccd/Thelonious: # ifconfig-push 10.9.0.1 10.9.0.2 # Suppose that you want to enable different # firewall access policies for different groups # of clients. There are two methods: # (1) Run multiple OpenVPN daemons, one for each # group, and firewall the TUN/TAP interface # for each group/daemon appropriately. # (2) (Advanced) Create a script to dynamically # modify the firewall in response to access # from different clients. See man # page for more info on learn-address script. ;learn-address ./script # If enabled, this directive will configure # all clients to redirect their default # network gateway through the VPN, causing # all IP traffic such as web browsing and # and DNS lookups to go through the VPN # (The OpenVPN server machine may need to NAT # or bridge the TUN/TAP interface to the internet # in order for this to work properly). push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" # Certain Windows-specific network settings # can be pushed to clients, such as DNS # or WINS server addresses. CAVEAT: # http://openvpn.net/faq.html#dhcpcaveats # The addresses below refer to the public # DNS servers provided by opendns.com. ;push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" # Uncomment this directive to allow different # clients to be able to "see" each other. # By default, clients will only see the server. # To force clients to only see the server, you # will also need to appropriately firewall the # server's TUN/TAP interface. ;client-to-client # Uncomment this directive if multiple clients # might connect with the same certificate/key # files or common names. This is recommended # only for testing purposes. For production use, # each client should have its own certificate/key # pair. # # IF YOU HAVE NOT GENERATED INDIVIDUAL # CERTIFICATE/KEY PAIRS FOR EACH CLIENT, # EACH HAVING ITS OWN UNIQUE "COMMON NAME", # UNCOMMENT THIS LINE OUT. ;duplicate-cn # The keepalive directive causes ping-like # messages to be sent back and forth over # the link so that each side knows when # the other side has gone down. # Ping every 10 seconds, assume that remote # peer is down if no ping received during # a 120 second time period. keepalive 10 120 # For extra security beyond that provided # by SSL/TLS, create an "HMAC firewall" # to help block DoS attacks and UDP port flooding. # # Generate with: # openvpn --genkey --secret ta.key # # The server and each client must have # a copy of this key. # The second parameter should be '0' # on the server and '1' on the clients. ;tls-auth ta.key 0 # This file is secret # Select a cryptographic cipher. # This config item must be copied to # the client config file as well. ;cipher BF-CBC # Blowfish (default) ;cipher AES-128-CBC # AES ;cipher DES-EDE3-CBC # Triple-DES # Enable compression on the VPN link. # If you enable it here, you must also # enable it in the client config file. comp-lzo # The maximum number of concurrently connected # clients we want to allow. ;max-clients 100 # It's a good idea to reduce the OpenVPN # daemon's privileges after initialization. # # You can uncomment this out on # non-Windows systems. ;user nobody ;group nogroup # The persist options will try to avoid # accessing certain resources on restart # that may no longer be accessible because # of the privilege downgrade. persist-key persist-tun # Output a short status file showing # current connections, truncated # and rewritten every minute. status openvpn-status.log # By default, log messages will go to the syslog (or # on Windows, if running as a service, they will go to # the "\Program Files\OpenVPN\log" directory). # Use log or log-append to override this default. # "log" will truncate the log file on OpenVPN startup, # while "log-append" will append to it. Use one # or the other (but not both). ;log openvpn.log ;log-append openvpn.log # Set the appropriate level of log # file verbosity. # # 0 is silent, except for fatal errors # 4 is reasonable for general usage # 5 and 6 can help to debug connection problems # 9 is extremely verbose verb 3 # Silence repeating messages. At most 20 # sequential messages of the same message # category will be output to the log. ;mute 20 I've tried on multiple computers by the way. The same result on all of them. What could be wrong? Thanks in advance, and if you need other information I'll gladly post it. Information for new comments root@vps:~# iptables -L -n -v Chain INPUT (policy ACCEPT 862K packets, 51M bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 3 packets, 382 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 4641 298K ACCEPT all -- * * 10.8.0.0/24 0.0.0.0/0 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 1671K packets, 2378M bytes) pkts bytes target prot opt in out source destination And root@vps:~# iptables -t nat -L -n -v Chain PREROUTING (policy ACCEPT 17937 packets, 2013K bytes) pkts bytes target prot opt in out source destination Chain POSTROUTING (policy ACCEPT 8975 packets, 562K bytes) pkts bytes target prot opt in out source destination 1579 103K SNAT all -- * * 10.8.0.0/24 0.0.0.0/0 to:SERVERIP Chain OUTPUT (policy ACCEPT 8972 packets, 562K bytes) pkts bytes target prot opt in out source destination

  Read the article

• Best practice for Exchange 2010 HA topology considering 6 x Exchange licenses and TMG 2010

  - by MadBoy

  What would be best topology considering that: 6 x Exchange 2010 Standard Licenses 2 x Separate locations that are supposed to support redundancy in case of link problems 4 x Forefront TMG 2010 with Forefront Security and Forefront Protection/Security Multiple locations worldwide using those Exchange. Most locations will be connected with VPN Tunnel (the ones hosting Exchange for sure). I was thinking something like this: Location MAIN (about 70-100 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Location SUPPORT (about 20 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Management wants to make sure that in case of problems in main location (power failure, link loss etc) second location can support all traffic from around the world and vice-versa. We have 6-7 locations and more comming up (not big ones but like 10+ people per each location). I do know that CAS/HUB is single point of failure (and no NLB), but i simply lack more licenses to do some redundancy on that. What do you think about this approach? What would be better approach according to you?

  Read the article

• Moving Farm to co-location hosting - network settings requirements

  - by Saariko

  I am moving my farm (2 Dell's R620) to a co-location hosting service. I am trying to figure out the secure way to have my network settings The requirements are: VM1 is the working HOST, includes: esxi 5.1, vSphere, 4 clients (w2008r2 all) VM2 has esxi 5.1 installed, and a single machine with Veeam Backup and copy 6.5 - keeping a copy of VM1 clients on the VM2 internal storage (this solution is due to a very small budget - in case of failure on Host 1 - can redirect IP's) Only 2 VM clients require network address and access from the WWAN - ISP provides IP's range for them (with Gateway and DNS) I need connection to the iDrac's from my office (option to create a VPN-SSL tunnel) Connection to the vSphere appliances I want to be able to RDP to the VM clients The current configuration is that each host has the iDrac dedicated nic connected , and another (NIC #1) connected - with a static IP on 192.168.3.x The iDrac's have a static IP from the same network range (19.168.3.x) It will look something like this: My thoughts: On NIC#2 of both hosts I will connected a crossed cable I will give each VM clients that needs internet access a 2ndry VM network with the assigned IP from the ISP open only to web - can not access from the My Question: Should I give IP's (external) to the machines who DO NOT require WWAN Access? - I can't see a way to RDP to them directly if not. Should I use the crossed cable? or just plug NIC #2 to the switch? Will this setup even work? What do I need to verify? What Virtual nic's and/or switches should I create on the Hosts?

  Read the article

• Cisco QoS Guidance

  - by Kyle Brandt

  I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

  Read the article

• Ubuntu 12.04 - HP ProLiant DL380 G4 - Load Maxes Out / Unresponsive

  - by Brian S

  Trying to post this question on here. I've posted it on the Ubuntu forums as well with no replies. Recently I upgraded an HP ProLiant DL380 G4 server from Ubuntu 10.04 server to Ubuntu 12.04 server. Upon doing so, the server will not - at random times - get to a load of 400+ and then become completely non-responsive. I use an SNMP graphing program (cacti) and the load steadily increases by about 10 every five minutes until it gets over 400 and the graphing stops. The graphs may not be accurate, but the CPU load averages about 3% before this happens - and right when the load starts increasing, it jumps to about 25% for 15 minutes and dramatically dips down to less than 1% (about 0.3%) until the graphing stops. I'm not able to open a SSH tunnel to the server to do anything. I've checked the /var/log/syslog and all logging stops at that time as well - with nothing else in there. The odd thing is - the server still responds to DNS queries for the zones it is authoritative on during this time - and at normal speed. Just not sure what the next step would be in order to find out what is going on - and how this issue can be corrected. The server cannot stay with Ubuntu 10.04 Server and needs to stay upgraded.

  Read the article

• DNS issue for internal website routing internet connection from remote location

  - by Michael Paul

  I have an issue that I could use some help with. Our company has a main location and a remote location. Previously, the remote location was connected to the main location through an internet connection VPN tunnel. The connection was pitifully slow at 1.5Mbps, so we upgraded it with a 75Mbps direct link. That meant the remote location lost it's internet access, so we routed their access through the main office internet connection. Everything works perfect except for one thing. The website we host is not accessible from the remote location unless the IP address is used. If I do NSLOOKUP on our website address from a machine connected to the main location network, it resolves correctly to the inside IP address. However, if I do the same from a remote location machine, it resolves to the website's outside IP address. Our internal DNS server(s) have a pointer and CNAME records set up, and everything was working perfectly before the connection was upgraded. In addition, the remote location has a domain controller, DNS server and DHCP server to service these requests at the remote location and prevent these requests from getting routed back and forth over the link. So I think was it happening is that for some reason the DNS server at the remote location is not resolving our website name correctly and passing the requests on to the routers, which then push the request out to the internet DNS system. That resolves the name to our external IP. This is purely a DNS issue, everything else works just fine. I am just stumped on this one. Any ideas on how to fix this? Edit: I forgot to mention that at the remote side of the link is a Cisco ASA-5505 and at the main office there is a Cisco ASA-5510. The link is connected between these 2 devices and the routing is handled in the 5510. Thanks, Michael

  Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32  | Next Page >