Search Results

Search found 7875 results on 315 pages for 'wired networking'.

Page 27/315 | < Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >

  • Ubuntu Server: Networking fails with MODPROBE option in /etc/network/interfaces ... ??

    - by neezer
    For some reason (which I haven't been able to determine yet), yesterday morning the networking service on our web server (running Ubuntu 8.04.2 LTS -- hardy) wouldn't start, and our website went down. I noticed the following error message when trying to restart it: * Reconfiguring network interfaces... /etc/network/interfaces:6: option with empty value ifup: couldn't read interfaces file "/etc/network/interfaces" ...fail! Line 6 in the /etc/network/interfaces file concerned a MODPROBE command, which (I believe) loaded in the ip_conntrack_ftp module so that I could use PASV on my FTP server (vsftpd): (breaking modprobe commands commented out below) # Used by ifup(8) and ifdown(8). See the interfaces(5) manpage or # /usr/share/doc/ifupdown/examples for more information. # The loopback network interface auto lo iface lo inet loopback #MODPROBE=/sbin/modprobe #$MODPROBE ip_conntrack_ftp pre-up iptables-restore < /etc/iptables.up.rules # The primary network interface # Uncomment this and configure after the system has booted for the first time auto eth0 iface eth0 inet static address xxx.xxx.xxx.xxx netmask 255.255.255.0 gateway xxx.xxx.xxx.1 dns-nameservers xxx.xxx.xxx.4 xxx.xxx.xxx.5 I've verified that there is a file in /sbin called modprobe. Like I said earlier, this setup had been working flawlessly until yesterday morning (though my bosses say that the site actually went down the previous night at 11 PM EST). Can anyone shed some light on (A) why this broke, and (B) how can I re-enable the ip_conntrack_ftp module?

    Read the article

  • How do you initialize networking on a new Xen guest VM?

    - by Marten Veldthuis
    We have a Citrix XenServer setup, and while I personally lean more towards Dev than Ops, I've got an issue that's been bugging me. When you provision a new (Linux/Ubuntu) guest, how do you get it to have the correct IP-address? I'd want my application servers to exist in the range of 10.20.0.0/24, preferably being .1, .2, etc, so I can keep my sanity. I guess that the actual IP-address is something set in Linux itself, and Xen can't touch that, but then what's the best practice for getting it done? If you set up DHCP, don't you just move the problem to getting the adapters the "correct" MAC-addresses? Do you just have to hardcode a large table of MAC-addresses to IP-addresses, and then provision new guests always with the correct MAC-address on the virtual ethernet adapter? What we currently do is have an image of a "app server" that we boot up a new instance of, and then finalize it (with a script) that (among other things) modifies the /etc/networking/interface file to give it the correct IP. But that feels dirty to me, and I feel like surely there must a better way. Please enlighten me?

    Read the article

  • Virtualbox Networking: XP Guest, Ubuntu Host: Connecting to Windows servers & local network?

    - by user51833
    Here's what I have: Windows XP running in VirtualBox 3.0.8_OSE r53138; Host OS = Ubuntu 9.10 "Karmic Koala"; Windows network in my office with smb fileservers; Guest OS is connected to the internet and is sharing folders with Host OS; Limited networking expertise. Here's what I actually need to do: Use MS Outlook in my XP guest with all its calendar-sharing features and stuff (if this is all done through the internet then great) - or find a Linux app that can do the same stuff; Map Windows network servers, eg. smb://server01/ in my XP guest (I can already access these in Ubuntu. Here's what I've tried with no luck: Entering the server address (example above) in my XP guest windows explorer address bar (got a "could not access the file, path or drive" error message - maybe if I could enter login/pass information? But I don't know how); Mapping the server as a network drive (Windows could not find the path); Mounting the server as one of my shared folders (I couldn't find it through the shared folders browser in VirtualBox - is there somewhere in the Linux filesystem that Ubuntu keeps links to mounted servers?).

    Read the article

  • Client/Server game even in solo: any big problem?

    - by Klaim
    I'm making a game which have strong basic design based on multiplayer but also should provide a really interesting and self-sufficient solo game. A bit like a real-time strategy game. The events and actions taken shouldn't be as massive and immediate as in a FPS, so you can also think the networking like for an RTS. It's a PC game, targetting Windows, MacOSX and Linux (Ubuntu & Fedora). It's programmed in C++, using a variety of open source libraries, so I have great (potential) control over the performances. So far I always considered that just making the game work with two applications, client & server, even in solo mode was ok. However, as I'm in the process of starting the network code I'm having doubts about if it's a good idea. I'm not a specialist so I might be missing something in my analysis. I see these pros and cons: Pros: The game works only one way so if I fix a bug it should apply on all game modes, whatever the distance with the server is; Basic networking issues would be detected early, including behaviour with the protection softwares (firewall) installed (i am not specialist so this might be wrong); Cons: I suppose that even if it should be really fast enough, networking client and server on the same computer would still be slower than no networking and message passing in (one) process memory. Maybe debugging would be more difficult? I don't have experience in this case but so far I assume that debugging with Visual Studio allows me to debug multiple process so it shouldn't be really different. Also, remote debugging. My question is: is there a big disadvantage that I missed? Or maybe there are advantages that I missed and that should encourage me to just continue with only client-server game sessions?

    Read the article

  • Conference networking for the socially awkward

    - by Melanie Townsend
    Do you approach a room full of strangers with excitement at all the new people you’re going to chat to over coffee and a muffin as you swap tales of how you convinced your manager to give you the day “off”? Or, do you find rooms full of strangers intimidating and begin by scouting out a place you can stand quietly and not be in someone’s way until the next session begins? If you’re on the train to extrovert city, that’s great, well done, move along. If, on the other hand, a room full of strangers who all seem to inexplicably know each other already is more challenge than opportunity, then making those connections with other professionals can be more difficult. So, here’s some advice, some gleaned from other things I’ve read online when trying to overcome my own discomfort in large groups (hopefully minus the infuriating condescension), others are just things I’ve found helpful over the years. Start small Smaller groups are less intimidating, and, now that you’ve taken the plunge to show up, it’s harder to remain inconspicuous. I find it’s easier to speak to new people once the option NOT to has been taken away. You’re there now, smile through the awkward and you’ll be forever grateful when the three people you’ve met and gotten to know here are also at that gigantic conference later on (ideally, introducing you to other people). Smile, or at the very least, stop scowling You probably don’t even know you’re doing it. If your resting face doesn’t come across as manically happy, tinge that with some social anxiety and you become one great ball of unapproachable. Normally, I wouldn’t suggest this as a problem that needs fixing, I have personally honed this face to use while travelling alone all the time. However, if you are indeed hoping to meet some useful people and get the most out of this conference, you may need to remind yourself to smile. Prepare some ice breakers This is going to sound stupid, like “no one does this right?” stupid, but, just, trust me a minute. It’s okay to prepare. You don’t need to write word-for-word questions to ask people and practice them in a mirror – that would be strange. I’m suggesting to just have an arsenal of questions to ask people if you get stuck, what session has been your favorite, which ones are you most looking forward to, have you heard X presenter speak before, what did you think of them? Even just thinking about these things in advance can help, and, as a bonus, while the other person is answering it gives you a moment to tamp down that panic, I mean breathe, I mean get to know them. You’re not alone (in the least creepy way possible) See that person in the corner clutching their phone with a mild deer in the headlights look?  That is potentially your new conference buddy. Starting with something along the lines of: I don’t know about you, the sessions here are great but I find the crowds a little tough to deal with. Mind if I park here for a second? is a decent opener. Just walking around and looking at exhibitors (if applicable) is fine, but it’s a little too easy to wander about and not actually speak to anyone if that’s all you’re doing. If joining a group of people talking is too much to start with, one-on-one can be easier. Have goals Are there people in particular you wanted to speak to? Did you have a personal goal of speaking to at least “x” new people? Are you trying to get a contact in a specific company because you want to work with them on something? Does the business have vague goals as well that you may or may not be judged on later? Making specific goals you can accomplish lets you know whether you’ve actually succeeded in your “networking pursuits” or what you need to work on more for next time. Everyone’s got their own coping technique. Some people are able to remind themselves that “humans are fundamentally social creatures” and somehow that helps them, others drink which is not really something I recommend for professional conferences but to each their own, and some focus on the fact that networking can play a big role in their career path. Just do what works for you, and if there’re any tricks you’ve found helpful over the years, please share em.

    Read the article

  • What networking hardware do I need in this situation (Fairpoint [ISP] "E-DIA" connection)?

    - by Tegeril
    Right away you'd probably want to say, "Well just ask Fairpoint." I've done that, a number of times in as many different ways I can phrase it and just keep hitting a brick wall where they will not commit to giving any useful information and instead recommend contracting an outside firm and spending a pile of money. Anyway... I'm trying to help a family member out with an office connection that is being setup. I've managed to scrape tiny details here and there from our discussions with the ISP (Fairpoint in Maine) about what is going to be done and what is going to be needed. This is the connection that is being setup: http://www.fairpoint.com/enterprise/vantagepoint/e-dia/index.jsp Information I have been given: Via this connection I can get IPs across different C blocks if that were necessary (it is not) Fairpoint is bringing hardware with them that they claim simply does the conversion from whatever line is coming in the building to ethernet, they have referred to this as the "Fairpoint Netvanta" which I know suggests a line of products that I have looked up, but some (most? all?) of those seems to handle all the routing that I saw. Fairpoint says that I need to bring my own router to sit behind their device. They have literally declined to even suggest products that have worked for other clients in the past and fall back on "any business router works, not a home router." That alone makes my head spin. Detail and clarity hit a brick wall from there. At one moment I got them to cough up that the router I provide needs to be able to do VPN tunneling but they typically fall back to "not a home router" and I was even given "just a business router, Cisco or something, it'll be $500-$1000". Now I know that VPN tunneling routers exist well below that price point and since this connection is going to one machine, possibly two only via ethernet, my desire to purchase networking hardware that over-delivers what I need is not very high. They are literally setting all this up, have provided no configuration details for after they finish, and expect me to just plunk a $500+ router behind it and cross my fingers or contract out to a third party company. If there were other options available for the location, I would have dropped them in a second, but there aren't. The device that is connected requires a static IP and I'm honestly a bit hazy on the necessity of an additional router behind their device and generally a bit over my head. I presume that the router needs to be able to serve external static IPs to its clients, but I really don't know what is going to show up when they come to do the install. This was originally going to be run via an ADSL bridge modem with a range of static IPs (which is easy and is currently setup properly) but the location is too far from the telco to get speeds that we really want for upload and this is also a connection that needs high availability. Any suggestions would be greatly appreciated (I see a number of options in the Cisco Small Business line and other competitors that aren't going to break the bank…), especially if you've worked with Fairpoint before! Thanks for reading my wall of text.

    Read the article

  • I have a collection of dead consumer grade routers, should I buy a real one?

    - by Ex Networking Guy
    Am I crazy for considering purchasing a Cisco 2621 for the house? I am familiar enough with IOS to set up a simple gateway router, I don't really need the experience. At this point, I'm a developer so my days of crawling through CO's and under desks are long past me. But I am really sick of crappy consumer grade networking gear. Maybe I have lousy luck and this stack of WRTG54s is just because I have lousy power, or whatever.

    Read the article

  • From a Java programming perspective, what difference does multicast make to a networking program?

    - by pnut butter
    My manager has asked me to assess what changes would be required to add multicast support to a socket-based TCP/IP networking program that is part of a trading system. As far as I can tell, from the perspective of a Java program, it doesn't seem to matter too much whether the program is unicast or multicast. Doesn't the Java networking API make all of this transparent? By this I mean, wouldn't the change be a simple one of simply adding additional destinations for the outgoing connections?

    Read the article

  • Linux networking crash: best steps to find out the cause?

    - by Aron Rotteveel
    One of our Linux (CentOS) servers was unreachable last night. The server was not reachable in any way except for the remote console. After logging in with the remote console, it turned out I could not ping any outside hosts either. A simple service network restart solved the issue, but I am still wondering what could have caused this. My log files seem to indicate no error at all (except for the various daemons that need a network connection and failed after the network failure). Are there any additional steps I can take to find out the cause of this problem? EDIT: this just happened again. The server was completely unresponsive until I issued a networking service restart. Any advise is welcome. Could this be caused by a faulty hardware component? As per Madhatters request, here are some excerpts from the log at the time (the network crashed at 20:13): /var/log/messages: Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=100 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:01:05 graviton kernel: Firewall: *TCP_IN Blocked* IN=eth0 OUT= MAC=<stripped> SRC=<stripped> DST=<stripped> LEN=40 TOS=0x00 PREC=0x00 TTL=101 ID=256 PROTO=TCP SPT=6000 DPT=3306 WINDOW=16384 RES=0x00 SYN URGP=0 Dec 2 20:13:34 graviton junglediskserver: Connection to gateway failed: xGatewayTransport - Connection to gateway failed. The first three messages are simple responses to iptables rules I have set up through the LFD firewall. The last message indicates that JungleDisk, which I use for backups can no longer connect to the gateway. Apart from this, there are no interesting messages around this time. EDIT 4 dec: as per Mattdm's request, here is the output of ethtool eth0: (Please not that these are the settings that currently work. If things go wrong again, I will be sure to post this again if necessary. Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised auto-negotiation: Yes Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on Supports Wake-on: g Wake-on: d Link detected: yes As per Joris' request, here is also the output of route -n: aron@graviton [~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.xx.xx.58 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.42 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.43 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.41 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.46 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.47 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.44 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.45 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.50 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.51 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.48 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.49 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.54 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.52 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.53 0.0.0.0 255.255.255.255 UH 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 xx.xx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 xx.xx.xx.62 0.0.0.0 UG 0 0 0 eth0 The bottom xx.62 is my gateway. EDIT december 28th: the problem occurred again and I got the chance to compare some of the outputs of the above tests. What I found out is that arp -an returns an incomplete MAC address for my gateway (which is not under my control; the server is in a shared rack): During failure: ? (xx.xx.xx.62) at <incomplete> on eth0 After service network restart: ? (xx.xx.xx.62) at 00:00:0C:9F:F0:30 [ether] on eth0 Is this something I can fix or is it time for me to contact the data centre?

    Read the article

  • Server Side Developer Prerequisites

    - by Jking
    I am new to server side development and am currently learning node.js. What sort of networking information should I be familiar with to allow for a smooth learning curve with server side development. Could anyone provide resources pertaining to the information required to get into server programming? To give you a better idea of my standpoint: I do not know how a server interacts with a database [Q: How does a NoSQL database, or database in general, communicate with a server?] I am unsure of how a web stack works [Q: I have heard of LAMP but do not know how Apache, MySQL, and PHP interact. Hopefully this applies to other stacks as well. How do the components of a stack work together? Also, is a MEAN stack an alternative, or is it completely irrelevant to this] I have trivial knowledge of internet protocol [however extremely inefficient][Q: What resources are beneficial when learning about networking, and how much/what knowledge should I acquire to program on the server side] I am unsure of what I am unsure of concerning networking information necessary to start development Information on how the client-server model works would be greatly appreciated

    Read the article

  • Oracle Virtual Networking Partner Sales Playbook Now Available

    - by Cinzia Mascanzoni
    Oracle Virtual Networking Partner Sales Playbook now available to partners registered in OPN Server and Storage Systems Knowledge Zones. Equips you to sell, identify and qualify opportunities, pursue specific sales plays, and deliver competitive differentiation. Find out where you should plan to focus your resources, and how to broaden your offerings by leveraging the OPN Specialized enablement available to your organization. Playbook is accessible to member partners through the following Knowledge Zones: Sun x86 Servers, Sun Blade Servers, SPARC T-Series Servers, SPARC Enterprise High-End M-Series Servers, SPARC Enterprise Entry-Level and Midrange M-Series Servers, Oracle Desktop Virtualization, NAS Storage, SAN Storage, Sun Flash Storage, StorageTek Tape Storage.

    Read the article

  • Wired Connection shared with other computers connects then disconnects in 11.10 nm-applet

    - by approbatory
    connecting with shared with other computers connection in NetworkManager. Other computer gets IP but NetworkManager disconnects the shared connection after half a second. This same setup worked perfectly fine in 11.04. Is there any fix, workaround or alternative way to share a connection with another computer over an Ethernet cable. (I can downgrade to 11.04 but I'd rather not ). EDIT: found a workaround The workaround for now is to set IPv6 options to Ignore and then sudo killall dnsmasq. Reconnect and it should work.

    Read the article

  • Ubuntu KVM Networking

    - by Guest
    I have two VMs ( linux based VM ) running on a UBUNTU/QEMU KVM. I am looking at a simple networking model, where in the VMs have public address and need to talk to the outside world and the outside world should be able to talk to the VMs as well. I did this Created a bridge with A.B.C.D/16 ( class B address ) eth2 is part of the brige with A.B.C.E /32 host address VM's interface ( through TAP ) has A.B.C.F / 16 address eth2 and VM interface are both part of the bridge. Now however, I am unable to ping these address from the outside world. If i remove eth2 from the bridge, I am able to ping the eth2. Please let me know what is going on. Guest

    Read the article

  • No network connectivity (not wired or wireless) - RT5390

    - by Ben Udy
    I am starting to think I simply need to accept a small loss and sell my new ASUS K73E. Because I really don't enjoy computing when I have to deal with Windough$ and this windows 7 64 bit on my new ASUS is even worse than the old machines with XP. I have written to ASUS and they simply say "We don't support Linux" and while Ralink's website says they do support Linux I can't get anyone to tell me what model Ralink card might be in my machine. Is anyone out there who might be able to give me some useful advice???? Here is the answer to command lspci nn && lsusb && lsmod && rfkill list all: di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 di,snd_seq snd 54244 16 snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device uvcvideo 57374 0 videodev 34361 1 uvcvideo v4l1_compat 13251 2 uvcvideo,videodev soundcore 6620 1 snd snd_page_alloc 7076 2 snd_hda_intel,snd_pcm psmouse 63677 0 serio_raw 3978 0 lp 7028 0 parport 32635 2 ppdev,lp fbcon 35102 71 tileblit 1999 1 fbcon font 7557 1 fbcon bitblit 4707 1 fbcon softcursor 1189 1 bitblit video 17375 0 output 1871 1 video vga16fb 11385 1 vgastate 8961 1 vga16fb ahci 32360 2 Edit #2 lspci 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c49 (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 02:00.0 Network controller: RaLink Device 5390 03:00.0 Ethernet controller: Atheros Communications Device 1083 (rev c0) lsusb Bus 002 Device 002: ID 8087:0024 Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 13d3:5710 IMC Networks Bus 001 Device 002: ID 8087:0024 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Thanks for the suggestion because this gave me a model for Ralink RT5390. I have now gone to Ralink.com and downloaded (via Windows 7) the driver package (it is a bz2 file). I hope I can figure out how to install it. And FYI - I was not able to run su (not authorized?) and dmidecode didn't exist (probably needs to be downloaded BUT no internet yet in Ubuntu)

    Read the article

  • Laptops trying to connect via wireless? Only able to connect only via wired connection

    - by Chris J. Lee
    It seems that all the wireless laptops in the office have disconnected and are unable to reconnect to the wifi after a terrible storm caused some power interruptions. Troubleshooting actions Verify wireless broadcasting is up With each laptop i ended up flushing their dns cache on Win 7 (ipconfig /flush ) Performed an ipconfig /all to see what the new ip is Made sure password was correct Reset the router (multiple times) restarted each laptop. Tried connecting wirelessly Am i missing some small detail ? Network information The router is a linksys/cisco WRVS4400N router. Supports a lot of fancy features i don't know how to use. We have 3 static ip's the conference room computer, the wireless printer, my computer Mostly windows machines, we have 3 mac users

    Read the article

  • Ubuntu 10.04 says wired network disconnected, but it works

    - by mistily
    I've installed ubuntu 10.04, hoping to get rid of the 9.10 errors. (Nvidia driver didn't work quite properly, had some problems with clicking in flash, and I had -and still have- wired network working, but ubuntu said that it's disconnected) So the Nvidia driver is better now, but the network error is the same. I still have a working wired network connection, but when it starts says that it is disconnected. Notification area tells me the same thing. Why is that?

    Read the article

  • USB Wireless keyboard and wired mouse do not power on at system boot

    - by Victor S
    This did not use to be an issue but, I am not sure why, my USB keyboard and mouse are not powering on after system boot. I can fix the keyboard by taking out and then plugging back in the USB antennae, which makes it work right away, but the mouse, even if I un-plug it and plug it back in, it takes about two-three minutes until it receives any juice and starts working. Any ways I can debug this, or fix it? Thanks!

    Read the article

  • VMWare Player 5.0 Upgrade - Bridged Networking No Longer Works

    - by Syndog
    I've been using VMWare Player 4 on my Windows 7 PC, running my VMs under a bridged networking configuration without any problem. I settled on bridged networking two reasons... I often use VMs to host web applications for test purposes. I never could get NAT to work for me anyway, but no love lost, considering reason #1. Now that I've upgraded to VMWare Player 5, the situation has completely reversed. In other words, bridged networking no longer works at all, and NAT does. Has anyone else come across this? Any ideas on getting bridged networking to work again? This happens with both Windows and Linux guest OSes. VMWare Tools has been fully updated. I've tried the usual vmnetcfg.exe utility fix, to no avail.

    Read the article

  • How do I turn a Wi-Fi "hotspot" into a local wired network?

    - by Max Schmeling
    Here's the situation: In a remote "office" I have a computer with no network connection, that I need to network with when I'm at this remote office. There is a wireless network where this computer is, but no wireless adapter in the computer. I have a laptop running Windows 7 that can connect to the wireless, and the computer is running Windows Vista. What is the best way to get them both connected? I know I can buy a USB wireless adapter or something for the computer, but is there an easy way to do it with what I've got?

    Read the article

  • The Switch Workshop, by Red Gate and Re-Wired Group

    Customers don’t just buy a product — they switch from something else. And customers don’t just leave a product — they switch to something else. It’s in these switching moments that the deepest customer insights can be found. On the 25th of July, a select group of 32 people will attend a unique, hands-on, full-day workshop at Red Gate to learn about “The Switch”. ‘Disturbing Development’Grant Fritchey & the DBA Team present the latest installment of the Top 5 hard-earned lessons of a DBA – read it now

    Read the article

  • 12.10 Wireless networking

    - by user108594
    I downloaded ubuntu 12.10 using WUBI and cannot connect to the internet. I removed it and downloaded ubuntu 12.04 still cannot connect. This I assume rules out the program being the problem. I reinstalled 12.10. When loaded I get the same message W/red (x) stating Internet not connected. I went to the Settings drop down box and it does not reveal the network list but (enable networking has a ck mark). Am running a HP Laptop with a w/7/64 OS that has a kill switch that indicates (orangeno connection) I downloaded 12.10 on my desktop (on the same network) and everything OK. I tried to follow the instructions in the help menu but got lost and confused . Sincerely Dan Additional Info per request Broadcom 802.11b/g Wlan Internal pc [hp laptop] P.S. I've been out of town for about a month. TKS for your gitback I did install 12.10 via cd and everything ok,but retried alongside 7 and unable to connect to internet,also took laptop and hard wired using ethernet cable and everything ok. stumped again and running out of ideas!!!

    Read the article

  • Pinterest and Social Commerce: The Social Networking Site Retailers Shouldn’t Ignore

    - by Jeri Kelley
    If you are in the midst of remodeling your home, researching the latest spring fashion trends, or simply trying to figure out what to cook for dinner you’ve probably been on Pinterest, and like me, find it extremely useful for generating new ideas and storing them all in one place. Gone are the days of folding over corners of magazines or bookmarking the URL of a Web page – Pinterest makes it easy for you to “pin” ideas, photos, links, and more to virtual bulletin boards where your “followers” can repin, like, and share. As a consumer, Pinterest has gained my attention and I’m definitely not the only one. According to a Monetate infographic, Pinterest’s unique visitors increased 329% from September to December 2011. With this explosion of users, what does it mean for social commerce? Also according to Monetate, Pinterest is one of the top traffic drivers for retailers – driving even more traffic than popular social networking sites like Google+.  For businesses, creating a presence on Pinterest is a great way to extend the reach of your brand, increase inbound links, and drive more traffic to your site. Socialnomics has a great post on how some of the biggest retail brands are using Pinterest to connect with consumers, offer cool content, and engage on a more personal level. When evaluating your social commerce program, while Facebook still delivers the most referrals, Pinterest shouldn’t be ignored as a way to help reach and connect with as many consumers as possible.

    Read the article

  • Networking beim Vertriebsstammtisch

    - by A&C Redaktion
    Kennen Sie schon die Oracle Vertriebsstammtische? Mit dem neuen Format bieten wir unseren Partnern Networking in der reinster Form! Unsere Stammtische richten sich an alle Partner, die zuverlässige Informationen aus erster Hand möchten. Als Hersteller der weltweit umfassendsten Palette offener Unternehmenssoftware und Hardware bietet Oracle ein vollständiges Produktportfolio an. Diskutieren Sie mit uns über die gemeinsamen Chancen, die sich aus dem Ansatz „Engineered Systems“ und „Oracle on Oracle“ ergeben. Welche Synergien können wir erfolgreich gemeinsam nutzen, um den Markt zu erobern? Nehmen Sie teil und spüren Sie die Philosphie, die von den Teilnehmern unserer Partner gelebt werden soll. Im Anschluss an den fachlichen Teil laden wir Sie herzlich zum praktischen Teil des interaktiven Austausches ein! Die Teilnahme ist ausschließlich Oracle Partnern mit einer gültigen Oracle PartnerNetwork Mitgliedschaft vorbehalten und, unter Beachtung der aktuellen Teilnahmebedingungen, kostenlos. Agenda: 15:00-17:00 Alles zu den Software- und Hardware Produktneuheiten von der Oracle OpenWorld 17:00-17:30 Um 17:00 Uhr bitten wir alle Teilnehmer und Referenten, in eine Kochschule in direkter Nähe zu gehen/zu fahren - um dort den kulinarischen Part zu erleben: gemeinsam kochen, diskutieren und essen. 17:30-22:00 Der praktischen Teil dieses Vertriebsseminars findet in einer Kochlocation direkt im Anschluss statt.(Ihre Anmeldung gilt für das Vertriebsseminar und Ihre Teilnahme am praktischen Teil, dem Kochevent) Die nächsten Termine: 08.11.2012 bei Oracle in Düsseldorf mit anschließendem Abendessen19.11.2012 bei Oracle in Berlinmit anschließendem Abendessen28.11.2012 bei Oracle in Berlinmit anschließendem Abendessen

    Read the article

  • Networking beim Vertriebsstammtisch

    - by A&C Redaktion
    Kennen Sie schon die Oracle Vertriebsstammtische? Mit dem neuen Format bieten wir unseren Partnern Networking in der reinster Form! Unsere Stammtische richten sich an alle Partner, die zuverlässige Informationen aus erster Hand möchten. Als Hersteller der weltweit umfassendsten Palette offener Unternehmenssoftware und Hardware bietet Oracle ein vollständiges Produktportfolio an. Diskutieren Sie mit uns über die gemeinsamen Chancen, die sich aus dem Ansatz „Engineered Systems“ und „Oracle on Oracle“ ergeben. Welche Synergien können wir erfolgreich gemeinsam nutzen, um den Markt zu erobern? Nehmen Sie teil und spüren Sie die Philosphie, die von den Teilnehmern unserer Partner gelebt werden soll. Im Anschluss an den fachlichen Teil laden wir Sie herzlich zum praktischen Teil des interaktiven Austausches ein! Die Teilnahme ist ausschließlich Oracle Partnern mit einer gültigen Oracle PartnerNetwork Mitgliedschaft vorbehalten und, unter Beachtung der aktuellen Teilnahmebedingungen, kostenlos. Agenda: 15:00-17:00 Alles zu den Software- und Hardware Produktneuheiten von der Oracle OpenWorld 17:00-17:30 Um 17:00 Uhr bitten wir alle Teilnehmer und Referenten, in eine Kochschule in direkter Nähe zu gehen/zu fahren - um dort den kulinarischen Part zu erleben: gemeinsam kochen, diskutieren und essen. 17:30-22:00 Der praktischen Teil dieses Vertriebsseminars findet in einer Kochlocation direkt im Anschluss statt.(Ihre Anmeldung gilt für das Vertriebsseminar und Ihre Teilnahme am praktischen Teil, dem Kochevent) Die nächsten Termine: 08.11.2012 bei Oracle in Düsseldorf mit anschließendem Abendessen19.11.2012 bei Oracle in Berlinmit anschließendem Abendessen28.11.2012 bei Oracle in Berlinmit anschließendem Abendessen

    Read the article

  • networking without port forwarding

    - by Wallacoloo
    I'm trying to add networking functionality to my game. I want any user to be able to host the game, and anyone to be able to connect as a client. The client sends info to the host about their player's position, etc. When the host receives a message, it validates it and then broadcasts it to its other clients. I will primarily be dealing with UDP, but will also need TCP for chat & lobby stuff. The problem is that I can't seem to get a packet sent from the client to the host or the other way around without enabling port forwarding on my router. But I don't think this is necessary. I believe the reason I need port forwarding is because I want to send a packet from 1 computer on a LAN to another computer on a different LAN, but neither of them have a global ip address since they're in a LAN. So really, I can only send packets targeting the other network's router, which must forward it on to the machine I want to reach. So how can I do this without port forwarding? Somehow a web server can communicate with my computer, which doesn't have a global ip, without port forwarding. And I've played plenty of multi-player games that don't require me to enable port forwarding. So it must be possible. Btw, I'm using SDL_Net. I don't think this will change anything though.

    Read the article

< Previous Page | 23 24 25 26 27 28 29 30 31 32 33 34  | Next Page >