Search Results

Search found 7583 results on 304 pages for 'roger guess'.

Page 274/304 | < Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• What Sort of Server Setup Am I Likely to Need? - School A/V streaming

  - by DeathMagus

  My prior experience with servers has generally been limited to home file-sharing servers, low-traffic web-servers, and the like. This leaves me with the technical knowledge of how to set up a system, but little experience in terms of scaling said system. My current project, however, has me as the technical lead in setting up a school for online audio and video streaming. The difficulty I'm running into is that I don't quite have the experience to guess what they'll need, and they don't have the experience to tell me - so I've tried to ask as many pertinent questions about what they want to do with their server, and here's what I found out: About 1000 simultaneous users, and hoping to expand (possibly significantly) Both video and audio streaming, at obviously the highest quality possible Support for both live and playlist-based streaming. Probably only one channel, but as it's an educational opportunity, I imagine letting them have a few more wouldn't hurt. No word on whether they're locked into Windows or whether Linux is acceptable. Approximate budget - $7000. It may actually be about $2k less than this, because of a mishap with another technology firm (they ordered a $7000 DV tape deck for some reason, and now the company wants them to pay a 30% restocking fee). The tentative decisions I've already made: I'm planning on using Icecast 2 for my streaming server, fed by VLC Shoutcast encoding. Since the school already has a DMZ set up, I plan on placing the Icecast server in there, and feeding it through their intranet from a simple workstation computer in their studios. This system isn't in any way mission critical - it's an education tool (they're a media magnet school), so I figure redundancy is not worthwhile to them from a cost:benefit perspective. What I don't know is this: How powerful of a server will I need? What is likely to be my major throttle - bandwidth? How can I mitigate that? Will I need anything special for the encoding workstation other than professional video and audio capture cards and a copy of VLC? Are there any other considerations that I'm simply missing? Thanks a lot for any help - if there's more information you need, let me know and I'll tell you all I can.

  Read the article

• One user sometimes gets an unknown certificate error opening Outlook

  - by Chris

  Let me clarify a little. This isn't an unknown certificate error it's an unknown certificate error in so much as I can't figure out where the certificate comes from. This happens on a Win 7 Enterprise machine connecting to Exchange 2010 with Outlook 2010. The error he gets is that the root is not trusted because it's a self-signed cert. Take a look at this screenshot because even if I had generated this myself I wouldn't have put "SomeOrganizationalUnit" or "SomeCity" or "SomeState", etc. (Red block covers our domain name.) I'm a little concerned this is a symptom of a security breach. Exchange 2010 has three certificates installed but none of them are this certificate. They all have different expiration dates (one is expired) and different meta-data. edit: There are two scenarios that I see the certificate warning and one of them I can reliably repeat. When the user leaves his computer on over night Outlook pops the Security Warning window. I don't know what time this happens. Using Outlook Anywhere if I connect to Exchange externally via a cellular USB modem the Security Warning window will appear every time I close and reopen Outlook. Whether I say Yes or No does not make a difference on whether or not I can connect to Exchange and send/receive email. In other words, I can always connect to Exchange. I've checked my two Exchange servers and my Cisco router for a certificate that matches this one and I can't find it. edit 2: Here is a screenshot of the Security Alert window. (I've been calling it Security Warning... My mistake.) edit 3: I stopped seeing this error several weeks ago but I can't tie it to any single event (because I just sort of realized that warning had stopped showing up) but I think I found the source of the certificate. Last week I found out that the certificate on our website DomainA.com was invalid. I knew that our web admin had installed a valid certificate so when I look into the problem I found out I was being presented with the invalid certificate that this posting is in regards to. The Exchange server's domain is mail.DomainA.com so I can only guess that Outlook was passing this invalid certificate through as it did some kind of check on DomainA.com. This issue is still a mystery because the certificate warning stopped appearing several weeks ago whereas the invalid certificate issue on the website was only fixed last week. It ended up being a problem with the website control panel. The valid certificate was installed but not being served for some reason and instead the self-signed cert was being served.

  Read the article

• Why do I sometimes get 'sh: $'\302\211 ... ': command not found' in xterm/sh?

  - by amn

  Sometimes when I simply type a valid command like 'find ...', or anything really, I get back the following, which is completely unexpected and confusing (... is command name I type): sh: $'\302\211...': command not found There is some corruption going on I think. I don't use color in my prompt, I am using the Bash shell in POSIX mode as sh (chsh to /bin/sh and so on - $SHELL is sh). What is going on and why does this keep happening? Anything I can debug? I think this is more of an xterm issue than sh, or at least a combination of the two. Files, for context: My /etc/profile, as distributed with Arch Linux x86-64: # /etc/profile #Set our umask umask 022 # Set our default path PATH="/usr/local/sbin:/usr/local/bin:/usr/bin" export PATH # Load profiles from /etc/profile.d if test -d /etc/profile.d/; then for profile in /etc/profile.d/*.sh; do test -r "$profile" && . "$profile" done unset profile fi # Source global bash config if test "$PS1" && test "$BASH" && test -r /etc/bash.bashrc; then . /etc/bash.bashrc fi # Termcap is outdated, old, and crusty, kill it. unset TERMCAP # Man is much better than us at figuring this out unset MANPATH My /etc/shrc, which I created as a way to have sh parse some file on startup, when non-login shell. This is achieved using ENV variable set in /etc/environment with the line ENV=/etc/shrc: PS1='\u@\H \w \$ ' alias ls='ls -F --color' alias grep='grep -i --color' [ -f ~/.shrc ] && . ~/.shrc My ~/.profile, I am launching X when logging in through first virtual tty: [[ -z $DISPLAY && $XDG_VTNR -eq 1 ]] && exec xinit -- -dpi 111 My ~/.xinitc, as you can see I am using the system as a Virtual Box guest: xrdb -merge ~/.Xresources VBoxClient-all awesome & exec xterm And finally, my ~/.Xresources, no fancy stuff here I guess: *faceName: Inconsolata *faceSize: 10 xterm*VT100*translations: #override <Btn1Up>: select-end(PRIMARY, CLIPBOARD, CUT_BUFFER0) xterm*colorBDMode: true xterm*colorBD: #ff8000 xterm*cursorColor: S_red Since ~/.profile references among other things /etc/bash.bashrc, here is its content: # # /etc/bash.bashrc # # If not running interactively, don't do anything [[ $- != *i* ]] && return PS1='[\u@\h \W]\$ ' PS2='> ' PS3='> ' PS4='+ ' case ${TERM} in xterm*|rxvt*|Eterm|aterm|kterm|gnome*) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033]0;%s@%s:%s\007" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; screen) PROMPT_COMMAND=${PROMPT_COMMAND:+$PROMPT_COMMAND; }'printf "\033_%s@%s:%s\033\\" "${USER}" "${HOSTNAME%%.*}" "${PWD/#$HOME/~}"' ;; esac [ -r /usr/share/bash-completion/bash_completion ] && . /usr/share/bash-completion/bash_completion I have no idea what that case statement does, by the way, it does look a bit suspicious though, but then again, who am I to know.

  Read the article

• Multiple SSL Certificates Running on Mac OS X 10.6

  I have been running into walls with this for a while, so I posted at stackoverflow, and I was pointed over here... I am attempting to setup multiple IP addresses on Snow Leopard so that I can develop with SSL certificates. I am running XAMPP - I don't know if that is the problem, but I guess I would run into the same problems, considering the built in apache is turned off. So first up I looked into starting up the IPs on start up. I got up an running with a new StartupItem that runs correctly, because I can ping the ip address: ping 127.0.0.2 ping 127.0.0.1 And both of them work. So now I have IP addresses, which as you may know are not standard on OSx. I edited the /etc/hosts file to include the new sites too: 127.0.0.1 site1.local 127.0.0.2 site2.local I had already changed the httpd.conf to use the httpd-vhosts.conf - because I had a few sites running on the one IP address. I have edited the vhosts file so a site looks like this: <VirtualHost 127.0.0.1:80> DocumentRoot "/Users/jim/Documents/Projects/site1/web" ServerName site1.local <Directory "/Users/jim/Documents/Projects/site1"> Order deny,allow Deny from All Allow from 127.0.0.1 AllowOverride All </Directory> </VirtualHost> <VirtualHost 127.0.0.1:443> DocumentRoot "/Users/jim/Documents/Projects/site1/web" ServerName site1.local SSLEngine On SSLCertificateFile "/Applications/XAMPP/etc/ssl-certs/myssl.crt" SSLCertificateKeyFile "/Applications/XAMPP/etc/ssl-certs/myssl.key" SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown <Directory "/Users/jim/Documents/Projects/site1"> Order deny,allow Deny from All Allow from 127.0.0.1 AllowOverride All </Directory> </VirtualHost> In the above code, you can change the 1's to 2's and it is the setup for the second site. They do use the same certificate, which is why they are on different IP addresses. I also included the NameVirtualHost information at the top of the file: NameVirtualHost 127.0.0.1:80 NameVirtualHost 127.0.0.2:80 NameVirtualHost 127.0.0.1:443 NameVirtualHost 127.0.0.2:443 I can ping site1.local and site2.local. I can use telnet ( telnet site2.local 80 ) to get into both sites. But in Safari I can only get to the first site1.local - navigating to site2.local gives me either the localhost main page (which is included in the vhosts) or gives me a Access forbidden!. I am usure what to do, any suggestions would be awesome.

  Read the article

• Windows 7 & Virtual PC and Internet (gateway) problems on host PC

  - by Mufasa

  I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

  Read the article

• Recover strategy single bad sector in moricon

  - by Damon

  This week, my harddisk made me an early christmas present in the form of a single defect sector. To make up for the puny size of the present, it chose a sector inside moricons.dll for that. This means that now the system takes about 5 minutes to boot before Windows gives up and moves on, and there's 2 dozen scary "critical failure" entries in the system log after every boot, which is annoying. OK, admittedly, I shouldn't complain, it could be worse, the bad sector could be in ntldr... SMART info more or less indicates (for what SMART can indicate anyway) that the drive is mostly OK. Soft Read Error Rate has a score of 96, and Current Pending Sector Count has a raw value of 8, which translates to a score of 100. Acronis DriveMonitor makes this an issue (lowering the overall rating to 75%), HDD Health calls it "excellent", giving an overall rating of 95% (which is what this harddisk from day one). No single score is below 95 (power on hours and spin up count), and most are 100 anyway. Well, whatever, I've seen drives with perfect SMART values fail from one second to the other, and drives with moderate values work for years. So, I'm inclined not to put too much weight into that overall. TL;DR Now... to the problem: I don't feel like trashing the disk just yet (that's planned with a new OS install upgrading to Win7 early next year, independently of this issue), but in the mean time, I would still like to have a smoothly running system again. Therefore, I feel tempted to tamper with it, but before I render my system entirely unusable (since I've never done this before), I'd like to verify that my planned procedere is likely to suceed in having a working system again: Copy moricons.dl_ from the Windows install disk, rename it to moricons.zip, and unzip it. This gives an intact 5.1.2600.2180 version (the broken one is 5.1.2600.5512 - but I guess this makes not much of a difference, since it's an icon-only DLL, and an outdated copy should work better than one that can't be read) Run chkdsk /r /f` which will "repair" the file (i.e. delete the file without asking, tell the drive to remap the sector, and toss some unreadable junk into a file with a hexadecimal number) Hopefully Windows still boots after this (is that a reasonable expectation, or do I need to have something like BartPE ready? -- but then again, what's that good for in case chkdsk has nuked the entire file system...) Delete the junk file generated by chkdsk, copy the new DLL to %windir%\system32 Reboot. Pray. Maybe I just shouldn't touch anything, since it still kind of works... if annoying, but it works. Unsure... But, is there anything fundamentally wrong with the planned approach? Is this a sensible approach at all?

  Read the article

• Galera install failure on Fedora 18

  - by ehime

  I've been trying to reinstall MariaDB and have been encountering multiple issues, $ yum install Mariadb-Galera-server Error: Package: MariaDB-Galera-server-5.5.29-1.i386 (mariadb) Requires: galera Available: galera-23.2.4-1.rhel5.i386 (mariadb) galera galera = 23.2.4-1.rhel5 You could try using --skip-broken to work around the problem You could try running: rpm -Va --nofiles --nodigest there is a requirement that libssl.so.6 and libcrypto.ssl.6 are installed, these DO show up in my /lib64 and /lib though as linked items. /usr/lib -rwxr-xr-x 1 root root 1356700 Nov 23 2010 libcrypto.so.0.9.8e lrwxrwxrwx 1 root root 19 Jun 28 12:03 libcrypto.so.6 -> libcrypto.so.0.9.8e -rwxr-xr-x. 1 root root 394272 Mar 18 14:22 libssl.so.1.0.1e lrwxrwxrwx 1 root root 16 Jun 28 12:03 libssl.so.6 -> libssl.so.0.9.8e /usr/lib64 -rwxr-xr-x 1 root root 1849680 Mar 18 14:21 libcrypto.so.1.0.1e lrwxrwxrwx 1 root root 26 Jun 28 11:54 libcrypto.so.6 -> /lib64/libcrypto.so.1.0.1e -rwxr-xr-x 1 root root 421712 Mar 18 14:21 libssl.so.1.0.1e lrwxrwxrwx 1 root root 23 Jun 28 11:54 libssl.so.6 -> /lib64/libssl.so.1.0.1e So the deps SHOULD be met, trying to $ yum install galera returns this Resolving Dependencies --> Running transaction check ---> Package galera.i386 0:23.2.4-1.rhel5 will be installed --> Restarting Dependency Resolution with new changes. --> Running transaction check ---> Package galera.i386 0:23.2.4-1.rhel5 will be installed --> Finished Dependency Resolution No errors? but no install either .... ? lets try wget and rpm'ing the package instead I guess? $ wget https://launchpad.net/galera/2.x/23.2.4/+download/galera-23.2.4-1.rhel5.x86_64.rpm $ rpm -ivh galera-23.2.4-1.rhel5.x86_64.rpm This issues the dreaded error: Failed dependencies: libcrypto.so.6()(64bit) is needed by galera-23.2.4-1.rhel5.x86_64 libssl.so.6()(64bit) is needed by galera-23.2.4-1.rhel5.x86_64 But we saw above these packages are here =( Whats going on?? Is openssl not installed? $ yum install openssl Loaded plugins: langpacks, presto, refresh-packagekit Package 1:openssl-1.0.1e-4.fc18.x86_64 already installed and latest version Nothing to do Its there.... ??? wth Fedora?

  Read the article

• What are the most likely bottlenecks determining the performance of CamStudio screen recording?

  - by Steve314

  When doing screen recording, I can get a frame rate of maybe 15 frames per second for the full screen on my 1080p monitor using the XVID codec. I can increase the speed a bit by recording a region, changing screen modes, and tweaking other settings, but I'm curious what hardware upgrades might give me the biggest bang for my buck. My PC is budget, but modern... Athlon 2 X4 645 (3.1GHz, quad core, limited cache) processor. 4GB single channel DDR3 1066 RAM. ASRock motherboard with NVidia GeForce 7025/nForce 630a Chipset. ATI Radeon HD 5450 graphics card - 512MB on board, not configured to steal system RAM. I dual-boot Windows XP and Windows 7. For the moment, XP is my bigger performance concern as it's still my getting-things-done O/S as opposed to my browser-host O/S. My goal is to make a few programming-related tutorials. For a lot of that I don't need screen recording - I can make up some slides, record audio with the PC switched off, yada yada. When I do need screen recording, I'll mostly be recording Notepad++, Visual Studio or a command prompt. Occasionally, I may be recording some kind of graphics or diagram program and using my pre-Bamboo cheap Wacom tablet - I have the CS2 versions of Photoshop and Illustrator, but I'd much more likely be using Microsoft Paint. Basically, what I'll be recording won't be making huge demands on the machine - but recording a fair number of pixels (720p preferred) will be useful. What's particularly wierd - not so long ago I still had a five-year-old Pentium 4 based PC. And (with the same 1080p monitor) it could record at not far from the same frame rate. So clearly the performance issues are more subtle than just throw-money-at-it. My first guess would be that the main bottleneck is the bandwidth for transferring data to/from the graphics card. Is that likely to be correct? In support of that, see this [Radeon HD 5450 review][1] - the memory bandwidth is only 12.8 GB/s. If you can't get data out of graphics memory quickly, you can't transfer it back to the system memory quickly. Apparently, that's slower than some top-end cards in 2002.

  Read the article

• Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

  - by Shoshomiga

  I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

  Read the article

• FTP server questions

  - by Brad

  I'm currently trying to set up a home FTP server using debian and proftpd and I've run into a problem that has me confused. I have most things set up already, I believe, but I cannot access my ftp server using my external ip. I've forwarded the correct port on my router and I've checked http://www.yougetsignal.com/tools/open-ports/ to be sure that it is, in fact, opened. I've used telnet locally on my server to check that the port accepts connections. I am able to use ftp via LAN. But, I still cannot access anything externally. I'm thinking that there's still some router configuration to be done in order to fix this, such as routing all connections on my ftp port to my server via the internal ip, but I can't find any option on my router to do this. Is this a necessary step? There is an option to use DMZ hosting, but I'd rather avoid it if possible. I can provide additional information as requested, please let me know any information that you think could help at all. Thanks. -Brad PS - I have a Telus Actiontec Modem/Router Update - !! Trying my ftp server out at work, worked! I guess I did set it up correctly after all. What is confusing me, though, is why doesn't the server allow me to connect locally anymore? That seems very weird to me. Also, I don't really understand why I am denied outright if I attempt to connect from the same network using the external address. I'll look into it more when I get home, but thank you guys for your help. Update 2 - I found the problem with not being able to connect locally anymore. I was setting the masquerade address to my external IP and for some reason that was causing it to hang on MLSD when I connected using my LAN address. I've removed the masquerade address and I'm going to check if I need it at work tomorrow. I'll update this page if I find anything.

  Read the article

• Dlink search is hijacking my browser

  - by James

  For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

  Read the article

• D-Link DIR-300 slows down / loses network

  - by basic6

  there are 2 buildings (A and B). In bldg A is an open WLAN (which I'm allowed to use btw). In bldg B is a computer that I want to connect to that network. So I flashed an old D-Link DIR-300 AP with DD-WRT, mounted it to the wall (bldg B) near a window, attached a 13 dBi directional antenna (pointing to bldg A) and configured it as AP client in that wireless network. Then there's another AP, connected to the D-Link AP, acting as standard access point, which the computer is connected to. That's basically working so far, but: Every now and then the connection is lost. Not the connection between the computer and the D-Link (I can access the DD-WRT admin page normally) or the connection between the D-Link and the WLAN (in Status - Wireless it says it's still connected to the network), but when I want to access a web page (which only works if I'm connected to the wireless network from bldg A), my Firefox keeps "Looking for" (name resolution) without finding anything. When I reset the D-Link (power off, power on) in this situation, after some moments, everything's working fine again (Internet access). I've no idea why this is happening, but usually it's at most every few weeks (most times when nobody was using the computer, so no traffic). Compared to the connection speed when I connect directly to the WLAN in bldg A (Laptop), the speed in bldg B is rather slow, but I have the impression that this difference is worse in the last few days. A few minutes ago, I got 582 KB/s down and 911 KB/s up in bldg A (directly/laptop) and 84 KB/s down and 9 KB/s up in bldg B. The speed in bldg B used to be way higher (I remember 200 KB/s up) while the actual network speed in bldg A was lower than it is now (close to those 200). I'm aware that the wireless connection between those buildings should slow things down, but I'm wondering why this difference has become that extreme. Thanks for any tips... Update: I currently want to upload a large file (1.5 GB) via FTP (FileZilla). Since that caused the D-Link to disconnect (as described in first post), I took my laptop to bldg A, connected directly to the original WLAN (bypassing my D-Link) and tried the same upload. Guess what - same issue: At some point the connection is dead (at this point I would have reset my D-Link if I was connected to it). Just as the D-Link, my laptop is still connected, but not even name resolution is working ("Looking for..." in Firefox). After reconnecting, it's working again. Maybe my D-Link isn't the problem at all...

  Read the article

• only removing index.php rule works on my NginX and CodeIgniter as rewrite. Why?

  - by Atomei Cosmin

  I am very new in rewriting in nginx but although I've spent 2 days reading on forums, I still can't get some Codeigniter rewrites working ... server { listen *:80; server_name artademy.com www.artademy.com; root /var/www/artademy.com/web; index index.html index.htm index.php index.cgi index.pl index.xhtml; if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?/$1; } if (!-e $request_filename) { rewrite ^/(index.php\?)/(.*)$ /$1/mobile_app last; break; } error_log /var/log/ispconfig/httpd/artademy.com/error.log; access_log /var/log/ispconfig/httpd/artademy.com/access.log combined; ## Disable .htaccess and other hidden files location ~ /\. { deny all; access_log off; log_not_found off; } location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } location /stats { index index.html index.php; auth_basic "Members Only"; auth_basic_user_file /var/www/clients/client0/web3/.htpasswd_stats; } location ^~ /awstats-icon { alias /usr/share/awstats/icon; } location ~ \.php$ { try_files $uri =404; include /etc/nginx/fastcgi_params; fastcgi_pass 127.0.0.1:9012; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_param PATH_INFO $fastcgi_script_name; fastcgi_intercept_errors on; } } Codeigniter settings are: well for uri_protocol: REQUEST_URI; What i noticed is that from this rule: rewrite ^/(.)$ /index.php?/$1; it works ever if i write it like this: rewrite ^/(.)$ /index.php?; It might be a wild guess but it stops at the question mark... Anyhow what I need are rules as these from .htaccess: RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{QUERY_STRING} ^lang=([a-z]{2})$ RewriteRule ^([a-z]{2})$ index.php?/home_page?lang=$1 [L,QSA] RewriteRule ^([a-z]{2})$ index.php?/home_page?lang=$1 [L,QSA] #how_it_works RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^how-it-works/(en)$ index.php?/how_it_works?lang=en [L,QSA] #order_status RewriteCond %{REQUEST_FILENAME} !-f RewriteRule ^order-status/(en)$ index.php?/order_status?lang=en [L,QSA] Can anyone tell me what i'm doing wrong and show me a proper way for at least one rule? It would be more than helpful. Thank you in advance! ^^ PS: I made it work on apache by using Path_info for uri_protocol.. if this info is of any help, and i remember having kind of the same problem there too but switching to path_info made it all good.

  Read the article

• SQL Transactional Replication snapshot not applying

  - by dmch2

  Hi, I'm using SQL Transactional Replication with pull subscriptions to replicate databases (hosting their own distribution database) from several servers across a VPN to a central server. I've got the first 2 databases working fine but the 3rd one is causing me problems. My subscription server is SQL 2008, the source systems are all SQL 2005. The source databases are a few 100Mb in size and contain audit data so are simply growing slowly by adding new records at approx 1kb a second. As far as the replication monitor, Agent logs and event logs show everything is working fine - except that no data appears in my subscription database. The distribution agent doesn't seem to want to read the snapshot (and hence the initial state and schema) from the publisher. New transactions aren't applied although they do seem to be arriving OK as the replication monitor shows things like '5 transactions with 10 commands were delivered'. I would expect (as in previous times) to see statements about data being BCPed in the replication monitor. The snapshot is on the publisher on a shared folder. The subscriber can view the snapshot OK (\\repldata) and the alt snapshot folder is pointing at it. But the distribution agent doesn't seem to be making an attempt to do read it. I tried changing the snapshot path to something that's incorrect and didn't even get an error saying that it couldn't access it. After lots of googling etc I found that sp_MSget_repl_commands is called by the subscriber on the distribution database on the publisher. Running a profiler I can see that it's only called for one agent Id. After a reinit it's called for sequence number 0x0 as expected so I thought that would mean it's would look for the snapshot. However, looking on the publisher I see that there's data for two agents - the snapshot agent and the log reader agent (which is being queries). So I guess I need to tell the distribution agent to get the data for both. But how? and more importantly - why? It worked fine on the other two servers I've replicated. I'm not an SQL novice but this is pretty much my first go at replication so don't be afraid to accuse me of missing something obvious/stupid! I can get log files (eg from the distribution agent) if you want but they don't seem to have any errors in them - it just starts up and starts applying log reader agent changes. Cheers Dave

  Read the article

• Why does pinging a local router return "Destination Host Unreachable"?

  - by Matt H

  I have two tomato routers. One is bridged wirelessly with the other. I have a new server on the network. It's running Ubuntu Server 11.04. They are all connected like this: A - Linux PC B - New Server C - Mac Mini D - Macbook T1 - Tomato 1 T2 - Tomato 2 They are connected like so: A -----+-T1 ==== wireless bridge ==== T2----- ADSL modem | | C & D Connected wirelessly to T2 B -----+ A, C & D do not experience any issues. I have an active SSH session to B from A and it's not experiencing any loss. B, the new server occasionally cannot ping T2 and therefore cannot connect to the internet. However, A can always contact B and B can ping A and B When the network is lost, B can still ping T1, but not T2 yet at the same as B has lost connection to T2, A can still ping T2. Any ideas on what this could be? there is nothing that gives any clues in any of the logs on either router or the linux server. One thing that is interesting is that I set up a ping running between B and T2. T2 has the IP address 192.68.1.1 Here is what I am seeing: From 192.168.1.1 icmp_seq=26 Destination Host Unreachable From 192.168.1.1 icmp_seq=27 Destination Host Unreachable From 192.168.1.1 icmp_seq=28 Destination Host Unreachable From 192.168.1.1 icmp_seq=29 Destination Host Unreachable From 192.168.1.1 icmp_seq=30 Destination Host Unreachable From 192.168.1.1 icmp_seq=31 Destination Host Unreachable From 192.168.1.1 icmp_seq=33 Destination Host Unreachable From 192.168.1.1 icmp_seq=34 Destination Host Unreachable From 192.168.1.1 icmp_seq=35 Destination Host Unreachable 64 bytes from 192.168.1.1: icmp_req=36 ttl=63 time=3.40 ms 64 bytes from 192.168.1.1: icmp_req=37 ttl=63 time=5.70 ms 64 bytes from 192.168.1.1: icmp_req=38 ttl=63 time=2.25 ms 64 bytes from 192.168.1.1: icmp_req=39 ttl=63 time=2.18 ms 64 bytes from 192.168.1.1: icmp_req=40 ttl=63 time=3.12 ms 64 bytes from 192.168.1.1: icmp_req=41 ttl=63 time=2.15 ms 64 bytes from 192.168.1.1: icmp_req=42 ttl=63 time=1.97 ms 64 bytes from 192.168.1.1: icmp_req=43 ttl=63 time= And it cycles to being reachable and not. So I guess you could say the question is, why is the router responding that it cannot be reached?

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• CPanel has two entries for site, need to use SSL one

  - by beingalex

  I have a website that is meant to be using SSL, however there are two entries in Cpanel's httpd.conf which seem to be causing an issue. When I visit just www.website.com I require it to go to https://www.website.com. However I have to write the https:// directly for the site to work. The secure site also has a different IP. I am not meant to edit the httpd.conf directly either and am unsure as to how to change the following directives: <VirtualHost 1.1.1.1:80> ServerName website.com ServerAlias www.website.com DocumentRoot /home/websitec/public_html ServerAdmin [email protected] ## User websitec # Needed for Cpanel::ApacheConf <IfModule mod_suphp.c> suPHP_UserGroup websitec websitec </IfModule> <IfModule !mod_disable_suexec.c> <IfModule !mod_ruid2.c> SuexecUserGroup websitec websitec </IfModule> </IfModule> <IfModule mod_ruid2.c> RUidGid websitec websitec </IfModule> CustomLog /usr/local/apache/domlogs/website.com-bytes_log "%{%s}t %I .\n%{%s}t %O ." CustomLog /usr/local/apache/domlogs/website.com combined ScriptAlias /cgi-bin/ /home/websitec/public_html/cgi-bin/ </VirtualHost> <VirtualHost 2.2.2.2:443> ServerName website.com ServerAlias www.website.com DocumentRoot /home/websitec/public_html ServerAdmin [email protected] UseCanonicalName Off CustomLog /usr/local/apache/domlogs/website.com combined CustomLog /usr/local/apache/domlogs/website.com-bytes_log "%{%s}t %I .\n%{%s}t %O ." ## User websitec # Needed for Cpanel::ApacheConf <IfModule mod_suphp.c> suPHP_UserGroup websitec websitec </IfModule> <IfModule !mod_disable_suexec.c> <IfModule !mod_ruid2.c> SuexecUserGroup websitec websitec </IfModule> </IfModule> <IfModule mod_ruid2.c> RUidGid websitec websitec </IfModule> ScriptAlias /cgi-bin/ /home/websitec/public_html/cgi-bin/ SSLEngine on SSLCertificateFile /etc/ssl/certs/www.website.com.crt SSLCertificateKeyFile /etc/ssl/private/www.website.com.key SSLCACertificateFile /etc/ssl/certs/www.website.com.cabundle CustomLog /usr/local/apache/domlogs/website.com-ssl_log combined SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown <Directory "/home/websitec/public_html/cgi-bin"> SSLOptions +StdEnvVars </Directory> # To customize this VirtualHost use an include file at the following location # Include "/usr/local/apache/conf/userdata/ssl/2/websitec/website.com/*.conf" </VirtualHost> As you can see there is obviously the unsecure directive before the secure one. And this is probably the issue, however if I try to change the IP for the site in WHM I get an error saying that the IP (2.2.2.2) is already in use. Which it is I guess. Any help is appreciated.

  Read the article

• How to Deploy an ASP.NET Web API- and Browser-based Application to a Production Environment

  - by user69508

  (Please forgive if this is posted in an incorrect forum. We didn’t know exactly where to post it.) We have an ASP.NET Web API single page application - a browser-based app running in IIS to serve up HTML5/CSS3/JavaScript, which talks to the ASP.NET Web API endpoint only to access a database and transfer JSON data. Everything is working great in our development environment - that is, we have one Visual Studio solution with an ASP.NET Web API project and two class library projects for data access. While development and testing on development boxes, using IIS Express to a localhost:port to run the site and access the Web API, everything is fine. Now we need to move it to a production environment (and we’re having problems - or just not understanding what needs to be done). The production environment is all internal (nothing will be exposed on the public Internet). There are two domains. One domain, the corporate domain, is where all users login normally. The other domain, the process domain, contains the SQL Server instance that our app and Web API will need to access. The IT staff wants to put a DMZ between the two domains to house the IIS app and shield the users on the corporate domain from having access into the process domain directly. So, I guess what they want is: corp domain (end users) <– firewall (open port 80) <– DMZ (web server running IIS) <– firewall (open port 80 or 1433????) <– process domain (IIS for Web API and SQL Server) We’re developers and don’t really understand all the networking aspects, so we’re wondering how to deploy our browser/Web API application in this scenario. Do we need to break up our application so that all the client code (HTML5/CSS3/JavaScript/images/etc.) is on the IIS server in the DMZ, while the Web API gets installed on the server in the process domain? Or, does the entire app (client code and Web API) stay together on the IIS server in the DMZ, which then somehow accesses the SQL Server instance to get data? From the IIS server and app in the DMZ, would you simply access the Web API on the server in the process domain by going to "http://server/appname/api/getitmes"? In the second firewall between the DMZ and the process domain, would you have to open port 1433 or just port 80 since the Web API is a HTTP endpoint? Or, is there some better way of deployment (i.e., how ASP.NET Web API single page applications written all in HTML5 and JavaScript supposed to be deployed to production environments?)? I’m sure there are other questions, but we’ll start with these. Thanks!!! (Note: the servers are Win2k8 R2, SQL Server 2k8 R2, and IIS 7.5.)

  Read the article

• Troubleshooting Network Speeds -- The Age Old Inquiry

  - by John K

  I'm looking for help with what I'm sure is an age old question. I've found myself in a situation of yearning to understand network throughput more clearly, but I can't seem to find information that makes it "click" We have a few servers distributed geographically, running various versions of Windows. Assuming we always use one host (a desktop) as the source, when copying data from that host to other servers across the country, we see a high variance in speed. In some cases, we can copy data at 12MB/s consistently, in others, we're seeing 0.8 MB/s. It should be noted, after testing 8 destinations, we always seem to be at either 0.6-0.8MB/s or 11-12 MB/s. In the building we're primarily concerned with, we have an OC-3 connection to our ISP. I know there are a lot of variables at play, but I guess I was hoping the experts here could help answer a few basic questions to help bolster my understanding. 1.) For older machines, running Windows XP, server 2003, etc, with a 100Mbps Ethernet card and 72 ms typical latency, does 0.8 MB/s sound at all reasonable? Or do you think that slow enough to indicate a problem? 2.) The classic "mathematical fastest speed" of "throughput = TCP window / latency," is, in our case, calculated to 0.8 MB/s (64Kb / 72 ms). My understanding is that is an upper bounds; that you would never expect to reach (due to overhead) let alone surpass that speed. In some cases though, we're seeing speeds of 12.3 MB/s. There are Steelhead accelerators scattered around the network, could those account for such a higher transfer rate? 3.) It's been suggested that the use SMB vs. SMB2 could explain the differences in speed. Indeed, as expected, packet captures show both being used depending on the OS versions in play, as we would expect. I understand what determines SMB2 being used or not, but I'm curious to know what kind of performance gain you can expect with SMB2. My problem simply seems to be a lack of experience, and more importantly, perspective, in terms of what are and are not reasonable network speeds. Could anyone help impart come context/perspective?

  Read the article

• How to stretch the image from one screen to two screens

  - by wxiiir

  I want to be able to stretch the image from one monitor to a second monitor even if i have to use some software to do it. For example i want the top half of the image that is now shown on my first monitor to occupy the whole second monitor and i want the bottom half to occupy the whole first monitor, or the other way around i don't really care as long as it works. I would be cool to know how to do the same stuff but to the left half and right half. I know that image pixels would have twice the lenght or height this way but i don't really care about it as long as it works so basically i want the stuff to show on both monitors but with the same pixels as before. I have a hd4870 and windows7 and hd4000 family doesnt support having two monitors behaving like a large one, only hd5000 upwards, this would solve my problems without any of the drawbacks but it just can't be done (or maybe it can via software but i'm just too tired of searching). A solution to make almost any graphic card have two monitors behaving like a large one is matrox dualhead2go but that's just as expensive as a good hd5000 card so it's not worth it. thanks in advance EDIT I guess that nobody so far was able to fully comprehend my problem that was very explicitly written but i will elaborate some more. My hd4870 can have 2 monitors working with it but some stuff like games won't run on both monitors, which sucks. There are some ways to circumvent this problem and two of them are perfect or almost perfect but expensive and the third would be a software solution that would make it possible. The first one is to have and hd5000 family video card which will work just fine with both monitors. The second is to have a matrox dualhead2go that will make my hd4870 detect my two monitors as a large monitor. The third is to have a software that makes my two displays be detected as a large display and then captures the output of the video card, splits the images and renders them as 2d images to both monitors OR a simpler one but that would make outputted pixels double the width or height would be to capture the output of the graphics card to one screen, split it in two and enlarge it to fit both monitors and then output it to the monitors. p.s. By capturing the output of the video card i mean just make the video card process the stuff in a certain way. Making the video card detect two monitors as a large one via software may be a bit impossible or impracticable but stretching the output as a 2d image from one to both monitors for some coders should be a walk in the park so it would be likely that such program would exist or that some widespread softwares for dual monitor would have such function in them.

  Read the article

• Cloud storage provider lost my data. How to back up next time?

  - by tomcam

  What do you do when cloud storage fails you? First, some background. A popular cloud storage provider (rhymes with Booger Link) damaged a bunch of my data. Getting it back was an uphill battle with all the usual accusations that it was my fault, etc. Finally I got the data back. Yes, I can back this up with evidence. Idiotically, I stayed with them, so I totally get that the rest of this is on me. The problem had been with a shared folder that works with all 12 computers my business and family use with the service. We'll call that folder the Tragic Briefcase. It is a sort of global folder that's publicly visible to all computers on the service. It's our main repository. Today I decided to deal with some residual effects of the Crash of '11. Part of the damage they did was that in just one of my computers (my primary, of course) all the documents in the Tragic Briefcase were duplicated in the Windows My Documents folder. I finally started deleting them. But guess what. Though they appeared to be duplicated in the file system, removing them from My Documents on the primary PC caused them to disappear from the Tragic Briefcase too. They efficiently disappeared from all the other computers' Tragic Briefcases as well. So now, 21 gigs of files are gone, and of course I don't know which ones. I want to avoid this in the future. Apart from using a different storage provider, the bigger picture is this: how do I back up my cloud data? A complete backup every week or so from web to local storage would cause me to exceed my ISP's bandwidth. Do I need to back up each of my 12 PCs locally? I do use Backupify for my primary Google Docs, but I have been storing taxes, confidential documents, Photoshop source, video source files, and so on using the web service. So it's a lot of data, but I need to keep it safe. Backup locally would also mean 2 backup drives or some kind of RAID per PC, right, because you can't trust a single point of failure? Assuming I move to DropBox or something of its ilk, what is the best way to make sure that if the next cloud storage provider messes up I can restore?

  Read the article

• Router behind Router--second router (and its clients) cannot be "seen" even after both routers are D

  - by Trioke

  Couple of terminology I guess I should get out of the way for consistency's sake throughout the post: External Router/Modem - SMC 8014WG - External IP 173.32.144.134 - Internal IP 192.168.0.1 Internal Router - LinkSys WRT120N - "External" IP of 192.168.0.175 - Internal IP 192.168.1.1 - Connected via Ethernet Cable (a really long one, from the basement to the second floor) PC - IP 192.168.200 - Connected Wirelessly via WAP2 Personal. Laptop - Used to try and diagnose the problem, a 4th machine to the setup which won't be part of the final setup once everything works. The actual problem: I've tried setting the LinkySys router as a DMZ'd client on the SMC router, and then DMZ'd the actual PC on the LinkSys. So the DMZ looks like this: On the SMZ, client with IP 192.168.0.175 is DMZ'd. On the LinkSys, client with IP 192.168.1.200 is DMZ'd. No dice. I then tried port forwarding the necessary port on the SMC to the LinkSys (lets just say, port 80). Then port forwarded Port 80 on the LinkSys to the PC. Same as the DMZ scenario above, but change DMZ with port forwarding. No dice, still :(. Now here's where I went stupid--and tell me if one should never do this--I enabled both DMZ and port forwarding at the same time. I fired up Opera--my browser of choice ;)--typed in 173.32.144.134:6333 and... ... Third time is the charm they say? Well, clearly not. Otherwise I wouldn't be here ;). To diagnose the problem, I enabled "Allow remote access to the Admin panel" on the LinkSys router, and specified port 6333 as the port to use. I port forwarded port 6333 on the SMC to 192.168.0.175, and access my external IP of 173.32.144.134:6333 in hopes of seeing the Admin panel... No dice (I think I've ran out of dice by now ;)). So to see where the problem was, I connected a laptop to the SMC via LAN cable, and typed in 192.168.0.175:6333, and viola, Admin Panel access! So the problem looks like it lies with the SMC--But that's as far as I've got, I've done the port forwarding, the DMZ'ing, and I've even disabled the built-in firewall for safe measures, but nothing worked. So, here I am. Unable to connect to the PC behind the Internal router externally, and without anything to go on other than to come here and ask for the wisdom of the the superuser folks :). If any more detail is required, just ask. (Apologies in advance, if questions should never be this long winded!)

  Read the article

• Windows Update and IE fail to connect, but Chrome fine?

  - by I Gottlieb

  Out of ideas on this one. (Running Windows Vista.) I have a program that accesses the internet to retrieve financial market data. One day it tells me that it can't log in -- timeout error. I check the documentation and it says must have a working copy of IE browser installed. I check IE (have IE9) and sure enough -- it just spins. No error message, not timeout, no 'try later' -- just spins -- as far as I can tell, indefinitely. Any page, any address. Even access to a localhost site just spins. Chrome works fine. So does another program I have that fetches market data. Windows 'diagnose and repair' says my internet connection is working fine. I tried uninstall/re-install of IE. Same spinning. I tried to install Windows Updates, and guess what? I can't. I comes up with error 80072efd; checked documentation for the error and it says I should check firewall blockage. Thing is, the only firewall I have is Windows Firewall, and obviously it wouldn't be blocking Windows Update. In contrast, Windows 'Help' in all programs has no problem accessing the Internet. I had a filter on the internet connection, and this was updated just prior to first appearance of the problem. But I uninstalled the filter entirely (official, with passwd from the company's service rep) -- and no difference. I'm guessing that a high level Windows network service file is corrupted -- used only by MS programs and their ilk, but how do I find it? I'd like to avoid having to do a clean install of Windows. Much obliged for any insight. IG Ramhound -- Thanks for reply. I'm familiar with virtual machines as in e.g. JVM or an emulator for an alternative architecture or (theoretical) Turing Machine equivalence. But I'm not familiar with the way you're using the term. Please clarify -- what one needs for this VM 'test' and why you expect it will provide an advantage of insight into the problem. And what sort of 'configuration issue' are you referring to? IG

  Read the article

• HttpWebRequest and Ignoring SSL Certificate Errors

  - by Rick Strahl

  Man I can't believe this. I'm still mucking around with OFX servers and it drives me absolutely crazy how some these servers are just so unbelievably misconfigured. I've recently hit three different 3 major brokerages which fail HTTP validation with bad or corrupt certificates at least according to the .NET WebRequest class. What's somewhat odd here though is that WinInet seems to find no issue with these servers - it's only .NET's Http client that's ultra finicky. So the question then becomes how do you tell HttpWebRequest to ignore certificate errors? In WinInet there used to be a host of flags to do this, but it's not quite so easy with WebRequest. Basically you need to configure the CertificatePolicy on the ServicePointManager by creating a custom policy. Not exactly trivial. Here's the code to hook it up: public bool CreateWebRequestObject(string Url) {    try     {        this.WebRequest =  (HttpWebRequest) System.Net.WebRequest.Create(Url);         if (this.IgnoreCertificateErrors)            ServicePointManager.CertificatePolicy = delegate { return true; };}One thing to watch out for is that this an application global setting. There's one global ServicePointManager and once you set this value any subsequent requests will inherit this policy as well, which may or may not be what you want. So it's probably a good idea to set the policy when the app starts and leave it be - otherwise you may run into odd behavior in some situations especially in multi-thread situations.Another way to deal with this is in you application .config file. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} <configuration>   <system.net>     <settings>       <servicePointManager           checkCertificateName="false"           checkCertificateRevocationList="false"                />     </settings>   </system.net> </configuration> This seems to work most of the time, although I've seen some situations where it doesn't, but where the code implementation works which is frustrating. The .config settings aren't as inclusive as the programmatic code that can ignore any and all cert errors - shrug. Anyway, the code approach got me past the stopper issue. It still amazes me that theses OFX servers even require this. After all this is financial data we're talking about here. The last thing I want to do is disable extra checks on the certificates. Well I guess I shouldn't be surprised - these are the same companies that apparently don't believe in XML enough to generate valid XML (or even valid SGML for that matter)...© Rick Strahl, West Wind Technologies, 2005-2011Posted in .NET  CSharp  HTTP  

  Read the article

< Previous Page | 270 271 272 273 274 275 276 277 278 279 280 281  | Next Page >