Search Results

Search found 20941 results on 838 pages for 'hard drive recovery'.

Page 29/838 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

  • How do I reset a lost password (using recovery mode requires me to type the password)?

    - by user16441
    I need to reset my password. I have followed these steps: How do I reset a lost Administrative(root) password? However, then I go to "root" or "netroot" recovery options, it tells me: Give root password for maintenance (or type Control-D to continue) Clearly, I do not know the root password. If I type Control-D, I return to the list of options. From this page I read: Under chapter 'The Other Way': 4. Highlight the line that begins kernel and press 'e' to edit But in the grub configuration file I have no line that starts with 'kernel'. Only: setparams 'Ubuntu...' recordfail set gxfpayload... insmod part_msdos insmod ext2 set root=... search --no-floppy... linux /boot/vmlinuz-2.6.38... initrd /boot/initrd.img-2.6.... Those are all lines in my grub. Which line should I edit? Or is there another way to reset my password?

    Read the article

  • Strange performance differences in read/write from/to USB flash drive

    - by Mario De Schaepmeester
    When copying files from my 8GB USB 2.0 flash drive with Windows 7 to a traditional hard drive, the average speed is between 25 and 30 MB/s. When doing the reverse, copying to the USB drive, the speed is 5MB/s average. I have tested this with about 4.5GB of files, a mixture of smaller and larger ones. The observations were the same on both FAT32 and exFAT file systems on the USB drive, NTFS on the internal hard disk. I don't think I can be mistaken in saying that flash memory has a lot higher performance than a spinning hard drive in both terms of reading and writing. For both memory types, reading should be faster than writing too. Now I wonder, how can it be that copying files from a fast read memory to a faster write memory is actually slower than copying files from a fast read memory to a slow write memory? I think that the files are stored in RAM before being copied over too, and there's caching as well, but I don't see how even that could tip the balance. It can only be in the advantage of writing to the USB drive, since it is "closer" to the SATA system than the USB port and it will receive data from the internal SATA HDD faster. Perhaps my way of thinking is all wrong or it just depends on the manufacturer of the USB pen. But I am curious.

    Read the article

  • SATA DVD drive refuses to read movie DVDs

    - by poke
    Hey, I have a problem with my DVD Drive (Asus DRW-2014L1T, most current firmware installed) on Windows 7 x64. When I insert a DVD movie and Windows starts to access the drive (for autoplay, or when I manually click on the drive icon), my computer hangs up in a particular way, while trying to read the disk. Explorer stops reacting and several programs won't run or their launch is horribly delayed (like the device manager). In th end, I can't access the movie and can't even eject the disk (probably because Windows is still trying to access it). To get the disk out of the drive I then have to reboot (which sometimes doesn't work either) and eject the disk before Windows boots. BIOS recognizes the drive just fine, and Windows is also able to read data disks (tried it with some software disks), but just refuses any movies. I have checked the region code in the device manager, but it is correct. My notebook is reading the disks just fine btw.. I remember having the same problem with an older drive as well, but I don't remember what I did to make it work again (maybe I didn't even fix the problem back then). I do remember however that booting with the disk inserted made Windows recognize the disk, however this doesn't work in this situation either. Do you have any idea what to do to fix that problem?

    Read the article

  • Putting and configuring grub on an external drive

    - by HisDudeness
    I want to put a bunch of minor emergency operating systems (such as GParted Live, DSL, Puppy Linux and so on) on a partitioned USB pen drive, with a dedicated grub boot loader on it, which I want to start when I select the drive in the BIOS to boot. The problem is: when writing grub boot options I must tell where kernel and initial ram files are located, but the USB drive can have different letters depending on when I did plug it in, if some others external drive were mounted. So, how can I write appropriate options which automatically refer to the drive grub is installed on without having to specify absolute paths, which might change (I mean, like (hd1,msdos1) ot /dev/sdb1)? And, while we are at it, can I have grub working on a device without an operating system on it to which it can refer? I mean, I want to address the command sudo grub-install /dev/sdb from the LMDE system I'm on right now, but I won't have LMDE on my pen drive. Is that a problem? And installing grub on another device, will I keep the grub I have right now on my HDD?

    Read the article

  • Mount an external drive at boot time only if it is plugged in.

    - by Jeremy
    I've got an entry for an external harddrive in my fstab: UUID="680C0FE30C0FAAE0" /jgdata ntfs noatime,rw But sometimes this drive isn't plugged in at boot time. This leaves me half way through a boot, with a prompt to "Continue Waiting, press S or press M" but no keypress has any affect at this stage (including ctrl-alt-delete, not even caps-lock). Short of writing a script to check the output of fdisk -l, how can I mount this drive at boot time only if it is present? It would be handy to have an fdisk entry for this drive, so I can just type mount /jgdata instead of needing a device name.

    Read the article

  • How to remove raid 5 array of 5 SAS and use only use one SAS at a time without writing any thing to disc for recovery

    - by murtaza hamid
    I have HP server ML370 g5 with 8 SAS, c drive 1 72 gb raid 0, d drive 2 72 gb raid 0, f drive 5 146 gb raid 5. 2 of 5 sas drive has got bad sectors and raid 5 is showing status failed. now i want to remove all this 5 SAS and put 1 by 1 in any of the bay to make its image for data recovery purpose without writing anything to the drive. how should i proceed. i also want to keep drive c and d intact. also is it possible if i put all this 5 drives in the bay with the same sequense will it recognise the raid 5 array ( i read some where its smart controller..just curious) many thanks in advance.

    Read the article

  • WD1000FYPS harddrive is marked 0 mb in 3ware (and no SMART)

    - by osgx
    After reboot my SATA 1TB WD1000FYPS (previously is was "Drive error") is marked 0 mb in 3ware web gui. Complete message: Available Drives (Controller ID 0) Port 1 WDC WD1000FYPS-01ZKB0 0.00 MB NOT SUPPORTED [Remove Drive] SMART gives me only Device Model and ATA protocol version 1 (not 7-8 as it must be for SATA) What does it mean? Just before reboot, when is was marked only with "Device Error", smart was: Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: WD-WCASJ1130*** Firmware Version: 02.01B01 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun Mar 7 18:47:35 2010 MSK SMART support is: Available - device has SMART capability. SMART support is: Enabled SMART overall-health self-assessment test result: PASSED SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 188 186 021 Pre-fail Always - 7591 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 229 5 Reallocated_Sector_Ct 0x0033 199 199 140 Pre-fail Always - 3 7 Seek_Error_Rate 0x000e 193 193 000 Old_age Always - 125 9 Power_On_Hours 0x0032 078 078 000 Old_age Always - 16615 10 Spin_Retry_Count 0x0012 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0012 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 77 192 Power-Off_Retract_Count 0x0032 198 198 000 Old_age Always - 1564 193 Load_Cycle_Count 0x0032 146 146 000 Old_age Always - 164824 194 Temperature_Celsius 0x0022 117 100 000 Old_age Always - 35 196 Reallocated_Event_Count 0x0032 199 199 000 Old_age Always - 1 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 What can be wrong with he? Can it be restored? PS new smart is === START OF INFORMATION SECTION === Device Model: WDC WD1000FYPS-01ZKB0 Serial Number: [No Information Found] Firmware Version: [No Information Found] Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 1 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Mar 8 00:29:44 2010 MSK SMART is only available in ATA Version 3 Revision 3 or greater. We will try to proceed in spite of this. SMART support is: Ambiguous - ATA IDENTIFY DEVICE words 82-83 don't show if SMART supported. Checking for SMART support by trying SMART ENABLE command. Command failed, ata.status=(0x00), ata.command=(0x51), ata.flags=(0x01) Error SMART Enable failed: Input/output error SMART ENABLE failed - this establishes that this device lacks SMART functionality. A mandatory SMART command failed: exiting. To continue, add one or more '-T permissive' options. PPS There was a rapid grow of " 192 Power-Off_Retract_Count " before dying. The hard was used in raid, with several hards from the same fabric packaging box (close id's). The hard drives were placed identically. Rapid means almost linear grow from 300 to 1700 in 6-7 hours. Maximal temperature was 41C. (thanks to munin's smart monitoring)

    Read the article

  • Windows XP Installation issue - cannot find hard disk

    - by Marco
    A friend of mine gave me a laptop with Windows 8 installed and nothing else. I don't like it so I am trying to remove it by installing Windows XP. I have a windows XP installation CD that I have used before and worked fine, but didn't work when I tried to install it on the Windows 8 machine. It keeps telling me I don't have a drive to install to. Then I log into Windows 8 again and install check partitions. I found 2 and tried to make a new one but it will only let me make one of 69mb. Next, I tied to find a way to go back to XP with BCD install and try to set the boot loader for XP but it wasnt there. Somehow I deleted the bootloader for Windows 8 and now it asks me for a recovery tool for media. I am not familiar with the laptop specs, but it is a Toshiba with about 250GB storage, and above 1GHz processor.

    Read the article

  • System chooses boot drive seemingly at random

    - by Zurahn
    I have a system with two identical 1TB harddrives, where I image to a backup drive using the dd command. When I boot up, though, despite setting harddrive priority in the BIOS, the system sometimes boots the main drive, sometimes boots the backup. My system dual-boots Xubuntu and Windows XP, if that means anything to you. Any ideas?

    Read the article

  • linux: automount internal hard drive during boot?

    - by John Doe
    i try to create my own NAS and i need to automount the internal sata disks during boot i know i could do using fstab but im searching for a more easy/generalized way so its easier to scale with less handwork needed for every hard drive attached (or every mainboard added to the cluster) so anyone knows how to automount internal disks without using fstab like ubuntu does for usb drives? im using ubuntu server 9.10 thx all

    Read the article

  • Drive not able to be added to Storage Spaces

    - by Bram Vanroy
    I am having difficulties trying to create a storage space. I have four Hard Drives in my computer. Samsung 128Gb SSD x2 Caviar Green 2TB Older 320 Gb drive I want to merge the two last ones. The problem is, that the 2TB drive does not show up in the configuration screen.: I formatted both hard drives so that can't be it. Any help is appreciated. Edit: larger view: http://bramvanroy.be/files/images/storagespaces.jpg

    Read the article

  • Burnt SATA Drive

    - by luvieere
    By stupid curiosity, I've connected the FDD power cable to the jumper pins of a SATA drive, and powered on the system. The SATA drive's controller burned out. What now? Can it be replaced, and still be able to read the disc?

    Read the article

  • computer not recognizing hard drive

    - by Elliott
    Hey, a few days ago my computer wouldnt boot..said something along the lines of "Please insert correct boot media and press any key" Its oldish so I tried what I could and just went out to buy new hard drive. Yesterday, installed it and it worked fine..put Windows XP onto in sp3 etc, turned on today and the same thing has happened ! Tried changing cables, remove graphics card etc, restoring bios to default but nothing works. Motherboard : Asus A8R32-MVP Deluxe Ram : 2GB HD : 320gb Hitachi Any ideas? Thanks :)

    Read the article

  • Macbook Pro keeps ejecting anything I put into the internal optical drive

    - by Wroblewski
    My hard disk crashed and I need to reinstall Mac OS X. I restart, insert the installation DVD, press c on the keyboard and the dvd ejects. I've tried different DVDs, even CDs. It's a Macbook Pro from march 2008. Is it broken? Or can it be something more severe like the firewire controller on the motherboard (since I noticed this after my hard drive started to act strangely)? I've ran Apple Hardware Test successfully.

    Read the article

  • How to recover unsaved PSD file on MacOSX

    - by cenk
    Adobe Photoshop creates temporary *.psb files for emergency recovery at this path: ~/Library/Application Support/Adobe/Adobe Photoshop CS6/AutoRecover The files created have names like _Untitled-10FDB62ECBABBFF5C8EAD958EBC9CFAE2E.psb with current user:group as designated owner. If you save the file you are working on OR you hit "don't save" when prompted, the temporary files are deleted. Now, system creates and deletes these files. I am trying to recover the emergency file but I think the "undelete" utilities were created assuming the "user" deletes the file - like going into the trash bin and then emptying the trash... Anyone having experience about this? Thanks.

    Read the article

  • Software or testing pipeline for testing multiple hard drives

    - by lions_leash
    I have a whole bunch of hard drives (maybe 10 or so) from a variety of sources that I'd like to test. If they work, I will put them in use and/or give them away. I was going to simply open up one of my machines and plug each one in, one at a time, and troubleshoot from there. Is there a way (or set of tools) that I can use to make this process easier and/or faster?

    Read the article

  • How to boot a partition using a virtual pc.

    - by Fantomas
    I have backed up my failing hard drive using a ddrescue Linux command to two partition files - p1 and p2 5GB and 90GB each. Now, without saving this back to an actual disk - is there a way for me to boot my old computer virtually, using Virtual PC or Parallels or VMWare? How? Thank you.

    Read the article

  • Windows External Harddisk drive letter after cloning boot partition to it

    - by gladiator2345
    I cloned my windows 7 installation on c: to external hard drive. I applied usb patch using pwboot and i could successfully boot into windows. But My problem is even though i am booting in to external hd the file reference and system path is pointing to c: on my internal hard disk. If i remove internal hd and boot it will get stuck at login screen. Is there any way i can force drive letter c: to my boot partition on external hd while booting from it.

    Read the article

  • External hard drive is recognized but not mounted in OS X

    - by Sam Bryant
    My external HD got unplugged without ejecting and my Mac will no longer mount the drive, but it recognizes it's there. I already tried repairing the disk in Disk Utility, and erasing it in Disk Utility, and it still won't mount. I can't imagine the hardware is actually damaged otherwise it wouldn't even recognize it (Right?). Is there any other software solution I can try? Recovering my files is not a concern.

    Read the article

  • How to corrupt my hard disk ?

    - by amit
    Hi superuser, Please tell me how to corrupt my hard disk. I have Dell Inspiron 6400 & it's under complete cover insurance. Operating system is WindowS Vista Premium. So please tell me the method which actually work & damage/corrupt my hd.

    Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >