Search Results

Search found 913 results on 37 pages for 'rebooting'.

Page 29/37 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • Sometimes, Synaptics Touchpad Tends Cursor to Top-Right Corner

    - by John Chadwick
    This has been a reoccurring issue for me, pretty much since I've owned this laptop (an ASUS G60JX.) Sometimes, the cursor will stop working properly and instead tend toward the top right of the screen. Basically, sometime into my usage (maybe after a couple hours) the touchpad will inevitably begin to malfunction, where it has confusing patterns of pushing the mouse cursor toward the top right of the screen. In addition, certain features (like momentum) seem to quit working entirely. It makes using the cursor extremely difficult. I've been having this issue across very many drivers. Pretty much as soon as multitouch came into the mix, although I don't believe multitouch has anything to do with it. It appears that, in the state of malfunction, it doesn't matter how you touch the touchpad, but where you touch it. Certain regions do not seem to trigger the cursor to move to the top right corner. In fact, no specific region seems to, but some areas do so more often than others. The issue can be resolved temporarily by putting the computer into sleep mode and awakening it. I have found no way to recreate this success without sleeping the computer or rebooting. Disabling and re-enabling the touchpad device does not do anything to resolve the problem. This issue does not affect my WACOM tablet nor any USB mice, and can be resolved (not to my satisfactory) by uninstalling the touchpad drivers. I'm looking for a solution, or at least a workaround that doesn't require sleep mode.

    Read the article

  • hp proliant dl360 disk diagnostic issue

    - by user1039384
    We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

    Read the article

  • Hugepages not utilized by MySQL 5.0, CentOS 5

    - by TechZilla
    I've set up Hugepages, but i'm not seeing any of them reserved. Have I missed a step, or for some particular reason, is MySQL is unable to utilize the Hugepages? I have not created a mount of hugetlbfs, although from what I read, MySQL would not call pages in such a manner. If I'm wrong, please let me know, as that would be a trivial solution. Almost all my MySQL tables are using InnoDB. NOTE: I created a hugetlbfs, no change as expected. Is it possible that rebooting would rectify this situation? I would not want to go through the procedure, as this is high availability, but would do so if necessary. This is the configurations, which I believe are relevant. /etc/sysctl.conf ... ## Huge Pages vm.nr_hugepages = 4096 vm.hugetlb_shm_group = 27 ## SHM kernel.shmmax = 34359738368 kernel.shmall = 8589934592 ... /etc/security/limits.conf ... mysql soft nofile 12888 mysql hard nofile 51552 @mysql soft memlock unlimited @mysql hard memlock unlimited /etc/my.cnf [mysqld] large-pages ... grep Huge /proc/meminfo HugePages_Total: 4096 HugePages_Free: 4096 HugePages_Rsvd: 0 Hugepagesize: 2048 kB id mysql uid=27(mysql) gid=27(mysql) groups=27(mysql) context=root:system_r:unconfined_t:SystemLow-SystemHigh tail -6 /var/log/mysqld.log InnoDB: HugeTLB: Warning: Failed to allocate 1342193664 bytes. errno 12 InnoDB HugeTLB: Warning: Using conventional memory pool 120808 15:49:25 InnoDB: Started; log sequence number 0 1729804158 120808 15:49:25 [Note] /usr/libexec/mysqld: ready for connections. Version: '5.0.95' socket: '/var/lib/mysql/mysql.sock' port: 3306 Source distribution I would really appreciate any help, I'm completely out of ideas. If I missed any more relevant configs, or diagnostics, please comment and I'll add it to the question.

    Read the article

  • How to Re-install an App that Shows up in the Appstore as 'Update' Instead of 'Buy App'

    - by Craig Reville
    So long story short: I dropped the wrong app into 'clean my mac' and I hit 'cancel' but it was too late by that point. I rebooted and appstore said it had an update, when I opened appstore it was showing an update for the app I just uninstalled. I tried clicking 'update' but it gives me an error saying it's unable to install after 'downloading'. When I try to go into 'purchased apps' it shows the app as uninstalled so I click 'install' and I get an error saying it's already installed. I'm running Lion OS X, latest version, updated, mac book pro is only a few months old. I tried searching through the entire system to remove all traces of the app, after rebooting appstore no longer shows the app and no longer shows the update but on the apps page it still says 'Update'. I tried reinstalling the app from desktop OUT of the appstore and again says the app is 'already installed'. So after reading more about lion I found an article that spoke about 'BundleID' being the thing that tells appstore what's installed and needing updating however I can't find the location of where the BundleID would be. Any thoughts? I've tried CCleaner, AppCleaner etc and none of them show the app, mainly because it is uninstalled. Update I've spoken to Apple Support who confirmed that there is a file in the system that connects separately to tell the system if there are updates available however they declined to inform me of any further details. Apple also referred me from technical support to iTunes App Store opposed to Mac App Store support and from there I have been referred to AppleCare who are currently 'investigating' this issue. Hopefully there will be a fix that's simple to implement for people having similar issues, this appears to be a more common issue than I previously thought.

    Read the article

  • SBD killing both cluster nodes when there are even small SAN network problems

    - by Wieslaw Herr
    I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

    Read the article

  • Windows 7 boot problem on a Lenovo Thinkpad Z61m 9450HAG

    - by Matt Taylor
    I recently did a full upgrade of Windows 7 on my Thinkpad. Everything worked fine after up until the second reboot (the first reboot after some updates installed worked OK). At second reboot time the system would just black screen before the Windows logo appears. Disk/wireless/power/battery lights are all lit and the disk light is active (flickering). However, if I remove my battery and boot with just power it boots fine and quickly, and everything is OK. Any help on why this won't boot with battery plugged in is greatly appreciated. I need to take this battery out on the road/trains, etc. A little more detail on this story. The battery I had inserted when doing the (failed) boot was a long life battery. I have not tried inserting this battery when Windows is logged in. I have another (normal life) battery that I have charged up within Windows. It has just got to 100% and I am about to reboot with it in. I am using the Lenovo power manager to diagnose the battery - all seems OK. I will report back shortly as to the outcome. OK, so I chose the reboot option from within Windows, the machine seemed to shutdown okay, but then stalled. It didn't turn off completely and didn't reboot, but just sat, with the fan humming, somewhere in between! I had to hold the power button in for a few seconds until the fan stopped and then hit the power button again to boot the machine from fresh. One good thing, with this battery (the normal one) it booted into Windows 7 the first time with a battery! So, now I have rebooting issues. I have 3 errors in the event log: A timeout was reached (30000 milliseconds) while waiting for the lxdxCATSCustConnectService service to connect. The lxdxCATSCustConnectService service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion. The following boot-start or system-start driver(s) failed to load: cdrom Any thoughts?

    Read the article

  • Vista won't boot. BSOD: Page fault in nonpaged area

    - by user31576
    Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

    Read the article

  • Deleting certain files sits at "preparing to recycle" on Windows 7?

    - by Rachel
    We recently setup one of our users with a brand new Windows 7 computer, however she is unable to delete certain files. With some testing, I found I cannot move, rename, or view properties of these files either. When trying to delete the file, it just sits at the "Preparing to recycle" popup, however the "from" section says "Discovering items..." Clicking "More Details" on the popup shows me that it can't find the file name or where it's recycling from: Other notes... All the affected files are .pdf files that get created via a scanner. Other pdf files are fine. Opening the files works fine. I can open the file, Save As a new file, and delete the new one just fine Trying to delete the file via command prompt just sits there Rebooting the computer will let me manipulate the files like normal, however this user is responsible for scanning hundreds of documents a day and I'd rather not have to tell her to reboot her computer to delete files. The user is part of the administrator group on the computer The Owner of the affected files is the user attrib of files is just A

    Read the article

  • Determining the Source of a Given File System Mount on Unix [migrated]

    - by phobos51594
    Background Recently I have run into a bit of a snag on my home FreeBSD server. I recently upgraded it to the latest stable release, and I have noticed some strange behavior with the /var partition. Originally, I had the system configured such that /var had its own partition with /var/run and /var/log in memory disks (/tmp, too). After the upgrade, I notice there is a new, fourth memory disk mounting directly to /var that I had not set up manually and is not in my fstab. It is only 28 megs or so in size and is causing problems when trying to update my ports collection. The ramdisk mounts atuomagically at boot and cannot be unmounted while in multi-user mode. If I drop to single user mode, I am able to unmount it without issue, however rebooting causes it to pop right back up. System specifications have been included at the end of the post. Question Is there any way to determine exactly what is mounting a given memory disk (or any filesystem, for that matter) after it has been mounted? Alternately, does anybody have any ideas what might have caused the new /var ramdisk to pop up? System Specification # uname -a FreeBSD sarge 9.1-PRERELEASE FreeBSD 9.1-PRERELEASE #0: Thu Nov 22 14:02:13 PST 2012 donut@sarge:/usr/obj/usr/src/sys/GENERIC i386 # df Filesystem 1K-blocks Used Avail Capacity Mounted on /dev/da0s1a 515612 410728 63636 87% / devfs 1 1 0 100% /dev /dev/da0s1d 515612 287616 186748 61% /var /dev/da0s1e 6667808 2292824 3841560 37% /usr /dev/md0 63004 32 57932 0% /tmp /dev/md1 3484 8 3200 0% /var/run /dev/md2 31260 8 28752 0% /var/log /dev/md3 31260 512 28248 2% /var <-- This # cat /etc/fstab # Device Mountpoint FStype Options Dump Pass# /dev/da0s1a / ufs rw,noatime 1 1 /dev/da0s1d /var ufs rw,noatime 2 2 /dev/da0s1e /usr ufs rw,noatime 2 2 md /tmp mfs rw,-s64M,noatime 0 0 md /var/run mfs rw,-s4M,noatime 0 0 md /var/log mfs rw,-s32M,noatime 0 0 Thank you in advance for any assistance.

    Read the article

  • How do I clear out the ssh-agent entries (on Mac OS X )?

    - by cwd
    I'm running Mac OS X, and it appears that after SSHing to several machines, using identity files, my 'ssh-agent' builds up a lot of identity / keys and then sometimes offers too many to a remote machine, causing them to kick me off before connecting: Received disconnect from 10.12.10.16: 2: Too many authentication failures for cwd It's pretty obvious what's happening, and this page talks about it in more detail: SSH servers only allow you to attempt to authenticate a certain number of times. Each failed password attempt, each failed pubkey/identity that is offered, etc, take up one of these attempts. If you have a lot of SSH keys in your agent, you may find that an SSH server may kick you out before allowing you to attempt password authentication at all. If this is the case, there are a few different workarounds. Rebooting clears the agent and then everything works OK again. I can also add this line to my .ssh/config file to force it to use password authentication: PreferredAuthentications keyboard-interactive,password Anyhow, I saw the note on the page I referenced talking about deleting keys from the agent, but I'm not sure if that applies on a Mac since they appear to be cleared after reboot anyhow. Is there a simple way to clear out all keys in the 'ssh-agent' (the same thing that happens at reboot)?

    Read the article

  • Winamp playing sound but no video

    - by Greg Sansom
    I am having problems playing video in Winamp (the movie I am trying to play is an AVI - not sure if other formats work). I have installed the K-Lite Codec Pack, and the video does work in Winamp Classic. I can also play the video in Winamp on another machine (although I can't remember the exact configuration details of that machine - and I don't think they're relevant). There are a few symptoms: The content of the Video view is either empty, transparent, or displays rendering from other programs. Opening the Visualization view shows the following error: MILKDROP ERROR DirectX initialization failed (GetDeviceCaps). This means that no valid 3D-accelerated display adapter could be found on your computer. If you know this is not the case, it is possible that your graphics subsystem is unstable; please try rebooting your computer and then try to run the plugin again. Otherwise, please install a 3D-accelerated display adapter. Trying to open streams via the SHOUTCast TV plugin shows Error opening video output, and the video does not open. Opening the file with WMC causes the following error (although the movie still plays): Error creating DX9 allocation presenter CreateDevice failed D3DERR_NOTAVAILABLE There are no warnings displayed in Device Manager, although the display adapter is the standard Windows one. Running DxDiag shows no problems (codec for Video listed as XviD 1.1.2 Final). GSpot reports that codecs are installed. System specs: - Windows Server 2008 r2 Standard 64-bit, with latest updates; - .NET 3.5.1 installed; - Winamp v5.6.01 (latest version); - DirectX 11 (Latest version); - K-Lite Codec Pack 7.0.0 (Full); - Machine is HP DC7600 - full specs here. Please comment if there is any more information which will help to diagnose the problem.

    Read the article

  • There are currently no logon servers available

    - by Ian Robinson
    I am running a Windows 7 laptop that is joined to my company's domain. When I installed Windows 7, I created an account for myself, joined to the domain, and it had been working quite well even though I'm physically remote most of the time, and not actually on the network. However, today I created a new local user account (non-admin) for my little brother. While he was using it, he decided he wanted to install a program, because his account is not an admin, he was prompted to enter Administrator credentials to allow the program to make changes to his computer. I entered my credentials, and this is the first time I ran into the error message: There are currently no logon servers available to service the logon request. I tried logging off and loggin back in, rebooting, etc etc, and no matter what, every time I try to authenticate as my "normal" domain account - I get that message. I can no longer access my computer as an administrator. I no longer know how to log in to my machine using any other account aside from my little brother's non-admin account. I don't have any other local accounts created, and the default local admin account was never enabled. I'd appreciate any ideas on how I can recover access to my account. Let me know if I can provide any more information. FYI - This is a similar question but not sure any of the answers help me in my case. http://serverfault.com/questions/71632/there-are-currently-no-logon-servers-available-to-service-the-logon-request

    Read the article

  • Amazon EC2 instance missing Network Interface

    - by Sergiks
    I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

    Read the article

  • Is execution of sync(8) still required before shutting down linux?

    - by Amos Shapira
    I still see people recommend use of "sync; sync; sync; sleep 30; halt" incantations when talking about shutting down or rebooting Linux. I've been running Linux since its inception and although this was the recommended procedure in the BSD 4.2/4.3 and SunOS 4 days, I can't recall that I had to do that for at least the last ten years, during which I probably went through shutdown/reboot of Linux maybe thousands of times. I suspect that this is an anachronism since the days that the kernel couldn't unmount and sync the root filesystem and other critical filesystems required even during single-user mode (e.g. /tmp), and therefore it was necessary to tell it explicitly to flush as much data as it can to disk. These days, without finding the relevant code in the kernel source yet (digging through http://lxr.linux.no and google), I suspect that the kernel is smart enough to cleanly unmount even the root filesystem and the filesystem is smart enough to effectively do a sync(2) before unmounting itself during a normal "shutdown"/"reboot"/"poweorff". The "sync; sync; sync" is only necessary in extreme cases where the filesystem won't unmount cleanly (e.g. physical disk failure) or the system is in a state that only forcing a direct reboot(8) will get it out of its freeze (e.g. the load is too high to let it schedule the shutdown command). I also never do the "sync" procedure before unmounting removable devices, and never hit a problem. Another example - Xen allows the DomU to be sent a "shutdown" command from the Dom0, this is considered a "clean shutdown" without anyone having to login and type the magical "sync; sync; sync" first. Am I right or was I lucky for a few thousands of system shutdowns?

    Read the article

  • Apache in OS X not displaying localhost nor vhosts correctly

    - by Marcus
    I've encountered a really odd problem in my development environment, and I really can't make any sense of it. It started by a locally developed PHP-site refused to update any content I edited in a file – no text or nothing. So if the document was: <h2>Hello!</h2> and I edited it to <h2>What's wrong?!</h2> it still outputed <h2>Hello!</h2>. I thought is was some kind of cache:ing problem, but no "hard reloads" in the browser nor sudo apachectl -k restart sorted it out. Only a restart of my Mac did finally fix it. Now, a few days later even stranger issues are appearing. I have a LAMP-stack installed via Homebrew, in httpd-vhosts.conf I've set ~/Dev/ as my localhost, and I set up a <VirtualHost *80> for each project ("ServerName projectname.dev" for example). However, what ever files of folder I put in ~/Dev/ have stopped showing up on localhost, and new VirtualHost-directives doesn't work. Three projects + "docs" in the folder: But "localhost" only displays the two older projects...? So, as I've said – I've tried restarting Apache (without errors), clearing browser caches (tried in three browsers, Chrome, Safari and Firefox) and ever rebooting the Mac. Nothing. Any ideas? Running OS X 10.8.5 and Apache 2.2.24.

    Read the article

  • Password Authentication Fails - NTLMv2

    - by JMeterX
    Environment: Windows 2000 sp4 EDIT: Domain Controller with no trust setup with the Win2008 Server Windows XP machines Windows 2008 Server Netapp NAS Problem: We have a shared folder that resides on a NAS using a Windows 2008 AD for the authentication with the proper permissions setup. When the Windows 2000 machine tries to open the share residing on the Win2008 machine, it is prompted for a username and password. Upon entering the credentials it continuously re-asks for credentials. Important Details: The Windows 2000 machine can ping both the XP machines and the Windows 2008 Server The Windows 2008 machine is mandated to only use NTLMv2 The Windows 2000 machine was originally set to NTLM but was recently switched to NTLMv2 if negotiated for the purpose of trying to connect to the share. As I am sure it will come up, we are using Windows 2000 because of contractual obligations Questions: Why is password Authentication failing in this case? After setting a GPO for the Win2000 machine for it to use NTLMv2, do we need to reboot the machine for the changes to take affect? We used SECEDIT to update the GPOs without rebooting. UPDATE We checked both of the 2008 Domain Controllers to find an error code. We received: Microsoft_Auth_Package_V1_0 0xc000006a Event ID: 4776 I know this to be an authentication error via THIS article "The value provided as the current password is not correct" We know this password to be correct, but since these two domains (Win2000 & Win2008) do not have a trust setup what authentication account needs to be used? One that resides on the Win2000 hosted domain?

    Read the article

  • Webapp in Jetty can't find properties file after running a couple days

    - by Cuga
    I have a webapp running in Jetty on Mac OS 10.6. After a few days of it running and without the server losing power or rebooting, it seems to stop working saying it can't find a properties file. This properties file is included inside the .war file deployed to the /webapps directory. If I restart Jetty as the superuser the web service works again just fine. Can anyone lend any advice to what's going on and how I can fix it? The error being shown when it isn't working is: Problem accessing /my-web-service. Reason: INTERNAL_SERVER_ERROR Caused by: java.lang.NullPointerException at com.company.service.Dao.readFromPropertiesFile(BwDao.java:35) at com.company.service.ServletHandler.doGet(ProxyClass.java:66) ... at org.mortbay.jetty.HttpConnection.handle(HttpConnection.java:404) at org.mortbay.io.nio.SelectChannelEndPoint.run(SelectChannelEndPoint.java:410) at org.mortbay.thread.QueuedThreadPool$PoolThread.run(QueuedThreadPool.java:582) Here's where the properties files exist that it's trying to read from the .war file: And this is how the properties are being read from the classpath: Properties properties = new Properties(); properties.load(Thread.currentThread().getContextClassLoader().getResourceAsStream( "app.properties")); Again, this does work just fine if I have just restarted the server, but it seems to fail after running a few days.

    Read the article

  • Unable to logon using terminal server connection

    - by satch
    I have several W2K3 SP2 servers, admin TS enabled. I discovered this morning, I was unable to logon into some of them. I've a couple of Citrix servers in different farms, a SAP (IA64) app server and a cvs server. All of them show same sympthoms; remote connections are refused. I've been able to logon locally, and terminal server service is up, there are no users (so connections are not depleted). There are no errors in log in most servers. One of the Citrix ones, reported following errors: Event ID 50 Source TermDD Type Error Description The RDP protocol component X.224 detected an error in the protocol stream and has disconnected the client. and Event ID 1006 Source TermService Type Error Description The terminal server received large number of incomplete connections. The system may be under attack. Anyway, I suppose these errors appear because server isn't working, and Citrix users try to logon massively. (I nmap'ed server and port seems up). I've solved this problem rebooting before, but with so many servers affected it seems like a crappy workaround. Any idea about troubleshooting it properly? Thanks in advance

    Read the article

  • Virtualization in Ubuntu 9.10

    - by Jeff Dege
    I have an existing Centos 5 installation. I would like to upgrade to Ubuntu. Thing is, I don't want to be down for as long as it will take to get my entire environment moved over - software installed, connectivity configured, etc. I'd like to take it one step at a time. But I don't really want to keep rebooting back and forth from the new OS to the old OS. That's what I did last time I upgraded to a new OS, and it got old real fast. So, since my new MB is virtualization-ready (AMD Phenom II 945 quad-core), I figured I could create a virtual machine, under the new OS installation, that ran the old OS installation. The problem is that the documentation I've been able to find has been pretty sparse. I've found a lot of possibilities, and little info on which would be capable of doing what I want. I have a new Ubuntu 9.10 installation, and a second disk containing the Centos 5 installation. And I don't know where to go next. Any help would be appreciated.

    Read the article

  • Windows Server 2008 can't start postgresql-x64-9.0 service: could not create any TCP/IP sockets

    - by Rob
    After rebooting a Windows Server 2008 machine to apply system updates, we recently we began having some issues running PostgreSQL 9.0. When we noticed the problem, we reverted the Windows updates, but the issue persists: From services.msc, attempting to start the postgresql-x64-9.0 service fails. Half-way through starting the progress bar becomes very slow, and eventually responds with error 1053; "the service did not respond in a timely fashion." Interestingly enough, bringing up the task manager shows multiple instances of postgres.exe have been started, and looking at the log file shows: 2011-02-10 14:44:02 ESTLOG: database system is ready to accept connections I then tried killing the processes, and starting via the command-line (as the user postgres), but I receive a different error: C:/Program Files/PostgreSQL/9.0/bin/pg_ctl.exe start -N "postgresql-x64-9.0" -D "F:/SHARE/postgres" -w waiting for server to start............................................................... pg_ctl: could not start server ESTWARNING: could not create listen socket for "192.168.0.101" ESTFATAL: could not create any TCP/IP sockets The log file again indicates that the database is ready to accept connections. Also, using netstat indicates that no other processes are using port 5432; I can't think of any other obvious reason that opening the listen socket might fail. Any help would be greatly appreciated.

    Read the article

  • What is the quickest and safest way to test new software and revert all changes, if needed?

    - by calbar
    I'm looking for Windows software that will allow me to quickly create a "checkpoint", do whatever I might need to do to my computer - install programs/drivers/updates, create/delete personal files, reboot the system multiple times, open questionable attachments - and then revert the entire system back to when the checkpoint was created. Essentially I want Windows Restore Points that save my personal files and partitions, too. It sounds like disk imaging might be the ticket, but creating them is much too slow and the restore process too involved... I'm hoping to sacrifice full disaster recovery for speed. Creating a checkpoint should be as close to one-click as possible, and rolling back should be a matter of selecting a restore point and rebooting. Ding! I'm familiar with Sandboxie, True Image Home "Try and Decide", Returnil, and a number of other "virtual system" apps that actively "catch" changes and allow you to commit or reject them. I'm not interested in these for a number of reasons - I prefer the "cut and dry" restore point approach. Finally, I'll note that I've just recently become aware of Comodo Time Machine. It sounds absolutely perfect, however, a quick skim through the user forums show more than a few horror stories of corrupted, unbootable systems. Any positive personal experience with the software to suppress my superstitions, or suggestions for more established alternatives would be greatly appreciated - Comodo Time Machine seems relatively new. Thanks for your help!

    Read the article

  • Can I share my cable internet connection through my ADSL wireless router?

    - by Roaders
    Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

    Read the article

  • After upgrading to 2008 R2 Enterprise and installing more RAM, Windows can only see 4.00 GB

    - by Tom Crane
    (I have also posted this on technet but I'm running out of ideas) I've upgraded from Windows Server 2008 R2 Standard to Enterprise in order to make use of more RAM. The server previously had 32GB of RAM. The upgrade from Standard to Enterprise, using DISM, seemed to go OK, so I powered down and installed the RAM. This a Dell Poweredge T710, I was taking it from 32GB to 72GB. The BIOS recognised the RAM, although I needed to change from "Advanced ECC" to "Optimizer" mode for it to use all of it. After rebooting, windows can see the RAM but in the system panel will display: Installed memory (RAM): 72.0 GB (4.00 GB usable) In the resource monitor, the remainder of the RAM is showing as reserved for hardware. I've tried various RAM configurations, including reverting it to the same chips and same configuration as before the upgrade, but always just 4.00 GB is showing up as usable. Following some threads on these forums I've gone into msconfig and set the maximum memory "by hand" but that doesn't fix the problem. BIOS doesn't seem to have anything that looks like memory remapping which is another suggestion that has come up. How do I make this RAM available to Windows? It was available before the upgrade, because I could use the full 32GB RAM the server had to start with. A screenshot (this is after reverting to the original RAM configuration) http://screencast.com/t/5FuzevdNb I don't know if it's related, but my remote desktop configuration has also disappeared: screencast.com/t/mYedomeQWS (the bottom half of this dialog should allow me to configure Remote Desktop, it was working before the upgrade but now it isn't).

    Read the article

  • Changing PATH Environment Variable for all Users. (Ubuntu)

    - by Wally Glutton
    I recently compiled Ruby Enterprise Edition (REE) on an Ubuntu 8.04 server. I would like to update my PATH to ensure this new version of Ruby (found in /opt/ruby_ee/bin) supersedes the older version in /usr/local/bin. (I still want the old version around, though.) I would like these PATH changes to affect all users and crontabs. Attempted Solution #1: The REE documentation recommends placing the REE bin folder at the beginning of the global PATH in /etc/environment. I altered the PATH in this file to read: PATH="/opt/ruby_ee/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" This did not affect my PATH at all. Attempted Solution #2: Next I followed these instructions and updated the PATH setting in /etc/login.defs and /etc/crontab. (I did not change /etc/sudoers.) This didn't affect my PATH either, even after logging out and rebooting the server. Other information: I seem to be having the same problem described here. I'm testing using the commands "echo $PATH" and "ruby -v". My shell is bash. My .bashrc doesn't override my PATH. Yes, I have heard of the Ruby Version Manager project. ;)

    Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >