Search Results

Search found 15249 results on 610 pages for 'tv shows'.

Page 29/610 | < Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >

• Atheros Wireless card shows up as two different models?

  - by geermc4

  Hi I've been fighting these wireless drivers for a few days and just recently i noticed that the model the Wireless controller appears in lspci is different sometimes. This is the data i have after installing Ubuntu Server 64 bit ~# lspci -k .... 04:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) Subsystem: AzureWave Device 1d89 Kernel driver in use: ath9k Kernel modules: ath9k ran some updates, restarted, all was good, all though it did say that linux-headers-server linux-image-server linux-server where beeing kept back. After that i installed ubuntu-desktop (aptitude install ubuntu-desktop --without-recommends) restarted and not only is the wireless not working anymore, but the hardware is listed as a different card ~# lspci -k .... 04:00.0 Ethernet controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) has no available drivers for it, still i tried to modprobe ath9k, they show up in lsmod as loaded, but still iw list shows nothing. this is what it looked like before the ubuntu-desktop instalation Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (14.0 dBm) * 2417 MHz [2] (15.0 dBm) * 2422 MHz [3] (15.0 dBm) * 2427 MHz [4] (15.0 dBm) * 2432 MHz [5] (15.0 dBm) * 2437 MHz [6] (15.0 dBm) * 2442 MHz [7] (15.0 dBm) * 2447 MHz [8] (15.0 dBm) * 2452 MHz [9] (15.0 dBm) * 2457 MHz [10] (15.0 dBm) * 2462 MHz [11] (15.0 dBm) * 2467 MHz [12] (15.0 dBm) (passive scanning) * 2472 MHz [13] (14.0 dBm) (passive scanning) * 2484 MHz [14] (17.0 dBm) (passive scanning) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor interface combinations are not supported Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS. What's with the hardware change? If it has 2, how can i make the AR9285 always load and disable AR5008, or, is it the same and it's just showing it different? :| Oh and I've tried this on Ubuntu 10.04 server, xubuntu 12.04, ubuntu 12.04 desktop and server. Thanks in advanced. -- Here's some more info, i have it setup in 2 hard drives, 1 works and the other one i'm using to figure it out The one that works... # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.147 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 01 serial: 74:2f:68:4a:26:73 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-18-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:fea00000-fea0ffff Here's where it doesn't # lshw -class network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: 54:04:a6:a3:3b:96 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.2.160 latency=0 link=yes multicast=yes port=MII speed=1Gbit/s resources: irq:43 ioport:e000(size=256) memory:d0004000-d0004fff memory:d0000000-d0003fff *-network UNCLAIMED description: Ethernet controller product: AR5008 Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:fea00000-fea0ffff Update I've noticed that if i blacklist the ath9k and ath9k_common modules lspci gives me the AR9285, but then I need to modprobe ath9k for it to work, does this make any sense? If so, why?

  Read the article

• How to Re-install an App that Shows up in the Appstore as 'Update' Instead of 'Buy App'

  - by Craig Reville

  So long story short: I dropped the wrong app into 'clean my mac' and I hit 'cancel' but it was too late by that point. I rebooted and appstore said it had an update, when I opened appstore it was showing an update for the app I just uninstalled. I tried clicking 'update' but it gives me an error saying it's unable to install after 'downloading'. When I try to go into 'purchased apps' it shows the app as uninstalled so I click 'install' and I get an error saying it's already installed. I'm running Lion OS X, latest version, updated, mac book pro is only a few months old. I tried searching through the entire system to remove all traces of the app, after rebooting appstore no longer shows the app and no longer shows the update but on the apps page it still says 'Update'. I tried reinstalling the app from desktop OUT of the appstore and again says the app is 'already installed'. So after reading more about lion I found an article that spoke about 'BundleID' being the thing that tells appstore what's installed and needing updating however I can't find the location of where the BundleID would be. Any thoughts? I've tried CCleaner, AppCleaner etc and none of them show the app, mainly because it is uninstalled. Update I've spoken to Apple Support who confirmed that there is a file in the system that connects separately to tell the system if there are updates available however they declined to inform me of any further details. Apple also referred me from technical support to iTunes App Store opposed to Mac App Store support and from there I have been referred to AppleCare who are currently 'investigating' this issue. Hopefully there will be a fix that's simple to implement for people having similar issues, this appears to be a more common issue than I previously thought.

  Read the article

• Do I need a web service for watershed.ustream.tv?

  - by Corey

  I am looking to use the watershed.ustream.tv service for a one-time event. Do I really need my own web service? In the control panel it says “WARNING: the test web service will always approve all requests so do NOT use it in a production environment!”. I'm not looking for any advanced features, I'm not even using the chat functionality. All I want to do is broadcast a funeral service without any advertising. I've looked for support on the watershed site, but I can't find any. Any help or advise would be appreciated.

  Read the article

• 1080p HD TV + what is minimum spec pc required to stream HD movie files to it?

  - by rutherford

  I want to stream hi-def (non flash-based) movies from my future minimum spec pc to my network-ready HDTV. What I want to know is a) when streaming from a computer (local wifi network), is the computer's cpu/video/ram resources used to the same extent as it would be if playing back on the computers local screen? If not what are the differences? b) So with streaming hd content what is the minimum spec processor I should go for, if i) only one TV is acting as client ii) two TVs are simultaneous clients.

  Read the article

• The Evolution of Television and Home Entertainment

  - by Bill Evjen

  This is a group that is focused on entertainment in the aviation industry. I am attending their conference for the first time as it relates to my job at Swank Motion Pictures and what we do for our various markets. I will post my notes here. The Evolution of Television and Home Entertainment by Patrick Cosson, Veebeam TV has been the center of living rooms for sometime. Conversations and culture evolve around the TV. The way we consume this content has dramatically been changing. After TV, we had the MTV revolution of TV. It has created shorter attention spans, it made us more materialistic, narcissistic, and not easily impressed. Then we came to the Internet. The amount of content has expanded. It contains a ton of user-generated content, provides filtering, organization, distribution. We now have a problem. We are in the age of digital excess. We can access whatever we want. In conjunction with this – we are moving. The challenge we have now is curation. The trends  we see: rapid shift from scheduled to on demand consumption. A move to Internet protocols from cable Rapid fragmentation of media a transition from the TV set to a variety of screens Social connections bring mediators and amplifiers. TiVo – the shift to on demand It is because of a time-crunch Provides personal experiences Once old consumption habits are changed, there is no way back! Experiences are that people are loading up content and then bringing it with them on planes, to hotels, etc. Rapid fragmentation of media sources Many new professional content sources and channels, the rise of digital distribution, and the rise of user-generated content contribute to the wealth of content sources and abundant choice. Netflix, BBC iPlayer, hulu, Pandora, iTunes, Amazon Video, Vudu, Voddler, Spotify (these companies didn’t exist 5 years ago). People now expect this kind of consumption. People are now thinking how to deliver all these tools. Transition from the TV set to multi-screens The TV screen has traditionally been the dominant consumption screen for TV and video. Now the PC, game consoles, and various mobile devices are rapidly becoming common video devices. Multi-screens are now the norm. Social connections becoming key mediators What increasingly funnels traffic on the web, social networking enablers, will become an integral part of the discovery, consumption and sharing model for Television. The revolution will be broadcasted on Facebook and Twitter. There is business disruption There are a lot of new entrants Rapid internationalization Increasing competition from existing media players A fragmenting audience base Web browser Freedom to access any site The fight over the walled garden Most devices are not powerful enough to support a full browser PC will always be present in the living room Wireless link between PC and TV Output 1080p, plays anything, secure Key players and their challenges Services Internet media is increasingly interconnected to social media and publicly shared UGC Content delivery moving to IPTV Rights management issues are creating silos and hindering a great user experience and growth Devices Devices are becoming people’s windows into all kinds of media from all kinds of sources There won’t be a consolidation of the device landscape, rather the opposite Finding the right niche makes the most sense. We are moving to an on demand world of streaming world. People want full access to anything.

  Read the article

• What Media Extender / Centre Set up should I use?

  - by Bryn Hird

  I have installed cat6 throughout the house which I use for telephony and network. In my cellar I have a NAS Server, gigabit switch and I want to install a Media Centre to stream my video's, music, photo's and live TV (coax from the aerial to the cellar) over the cat6. Yeah I know I can get stuff on the internet but shared experience of watching TV as a family as it happens is a big plus for live TV. I'm aiming for 1080p. I want different users to be able to watch different channels. Max users = 4. I've played a little with Windows Media Centre, works fine with live TV. Likewise I have XBMC up and running with live TV. The issue I have is what do I put near the TV. I'd like a consistent user interface (grandma and the the other technophobes in the house are continually pestering me on how to use different TVs, change channel, inputs etc.) so a key part of this for me is to make the user experience the same and simple i.e. no keyboards / PCs hanging around the TV. I've just bought a Linksys DMA 2200 to test the Windows Media Centre, but obviously off eBay as they're a dying breed. And with Windows Media Centre removed from Microsoft plans such devices will get rarer. And as for 1080p, think I can forget it with that set up. I have tested XBOX 360, also works but ditto on Microsoft plans for WMC. I was thinking of a WD Live TV to test the XMBC setup. Now to the question. Any advice on Media Centre / Extender setups that will do the job as above and have some degree of futureproofing (building my own with my Raspberry PI is a last resort). I'd like to understand the standards involved in the futureproofing if anyone knows (DNLA, RVU etc.).

  Read the article

• Putting a MovieMaterial behind a DAE model in Papervision3D

  - by didibus

  Hi, I'm doing a project using FLARManager augmented reality and the Papervision3D library. Unfortunately, Papervision is giving me a lot of problems. My scene3D contains a DAE model and a plane. The plane has a MovieMaterial and is playing a video through FLVPlayback. The DAE and the plane are both inside the same DisplayObject3D container. FLARManager transforms the container so that everything appears through the angle of the marker. My DAE model is a TV, the screen of the TV is transparent. I want to have my Plane inside of my DAE model, so that the Movie playing on the plane material appears to be what is playing on the TV. The problem is that, even if the plane has a lower Z index then the TV, it always appears in front of the TV. How do I have my plane and its MovieMaterial appear behind the TV, so that some of its corners are cut out by the TV and the part of the TV thats transparent let me see the Movie? If its impossible, anyone has an idea of how I could get the desired effect of having a movie play on the screen of my DAE tv model? Thank You.

  Read the article

• Few questions about a good projector on my PC and tv?

  - by jasondavis

  I have always wanted a projector for my tv, satelite, cable, and even PC in a spare bedroom. Well it's more of a home office that I spend most my time in and the catch here is it is a small room. Room is only the standard 8foot tall. Room is about 13 feet wide on the wall where I would like to mount the project and the wall where the screen would be for it. So only about 13 feet away from projector to screen. I would like to know... 1) From experience or knowledge what would be a good projector I could hook up to my satelite box and also my PC? Cheaper is better in this case but I would still like the best image for my buck and something reliable. There is no sunlight in the room either to worry about. 2) From that distance of about 12-13 feet away, how big of a clear picture could I expect? 3) What kind of cables would I need to purchase and run through my attic to my cable/satelite receiver box as well as my PC? 4) These cables in question 3 would most likely need to be a good 15-20feet in length to reach, would I need anything special for that to work at those distances?

  Read the article

• tcptrack shows SYN_SENT connections, does that mean the SYN package reached the server?

  - by xpu

  our server suffered a serious connection timeout problem, so we track tcp connection with tcptrack we found out that, if the client started to connect to the server, tcptrack shows the connection, but in SYN_SENT status, and netstat -nat shows nothing. (tcptrack & netstat all runs on the server) does this mean the syn request reached the server? and no syn/ack was sent back? why the tcptrack could report this connection but netstat could not? what could be the problem that a general apache could not establish a connection with the client? i did a bench test using ab in the same intranet, to the specified NIC, it handled 10000 concurrent connection and 400000 requests ok ps: this doesn't happen every time, but did happened a lot pps: is there any good tools to trace where the tcp connection was lost?

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Wireless shows up as disabled, how can I get it working?

  - by Lazer

  $ sudo iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off pan0 no wireless extensions. $ This is what pops up when I click the two computers icon What should I do to get Wifi working on this machine? $ sudo ifconfig wlan0 up SIOCSIFFLAGS: No such file or directory $ $ lspci | tail 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation ICH9M/M-E SATA AHCI Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc M92 LP [Mobility Radeon HD 4300 Series] 09:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8040 PCI-E Fast Ethernet Controller (rev 13) 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) $

  Read the article

• Microsoft Researchers shows off best Touch Screen ever made. Better than Apple touch screens!

  - by Gopinath

  All the touch devices we have in market today like iPads, iPhones, Samsung tablets and phones, etc.  have a very small issue – 100 milliseconds of lag. The lag is the amount of time a touch device takes to respond after you touch the device. The 100 milliseconds of lag may not be an issue when you are tapping and swapping the interface elements on a device, but they are apparent when you wing your finger around the screen faster. For example if you use any painting app, the lag is very obvious and screen responds slowly than an artist can paint with his finger. Researchers at Microsoft labs came out with a prototype of touch device that drastically cuts down the 100 milliseconds of lag time to just 1 millisecond. That’s 100 times faster than today’s touch screen devices. Check out the video embedded below for a demo of new touch screen. Over at TechCrunch, Chris Velazco says: The difference is staggering, especially when Dietz trots out the slow-motion footage. With the delay between touch input and screen response slashed by orders of magnitude, a device that sports the sort of super-low-latency Dietz envisions has the potential to feel far more (for lack of a better term) natural than its brethren. There’s zero delay when you slide a checker across a board, for example, and bringing that sort of instantaneous feedback to the many screens in our lives could help to bridge the gap between operating a bit of software and the feeling of interacting with objects.   It will be great boost to Microsoft’s tablet strategy if they succeed in bringing this research into mass market and allow it’s partners to use the technology on Windows 8 tablets.

  Read the article

• New blog post shows immediately in google search results where as other HTML content takes time, why?

  - by Jayapal Chandran

  I have a blog which has been active for 3 years. Recently I posted an article and it immediately appeared in google search. Maybe 5 to 10 minutes. A point to note is I was logged into my google account. Maybe google checked my post's when I searched since I am logged in? Yet I logged out and used another browser and searched again with that specific text and it appeared in google search result. How did this happen? However, if I make an article in static HTML and publish, it takes time. (I assume this is the case but I haven't tested much). Yet tested a few cases after updating it in my sitemap xml. How does google search work for a blog and other content?

  Read the article

• Can Simple & Modern UX Be Sexy? Fusion Apps in 100% #Oracle #ADF Shows How #usableapps #UX #futureofwork

  - by ultan o'broin

  YES! I love the sheer cut-to-the-chase instant beauty and usefulness of my Clear app on iOS. Dropbox really does simplify my ICT world, if not my life. I use those apps every day: on mobile, desktop or web. Clear app Dropbox web UI In the enterprise apps world, you'll love what Oracle Applications User Experience team is doing with our roadmap to simple and modern user experience with Oracle Fusion Applications built with 100% Oracle Application Development Framework (ADF). Simple and modern. A compelling and easily personalized UX for Fusion Apps on your device of choice. Beautiful. Simplicity, it's all part of the BYOD and COIT phenomenon that enterprises need to embrace rather than tolerate or ignore. So, introduce yourself to the new face of Oracle Fusion Applications. More on the Voice of User Experience for Oracle Applications blog.

  Read the article

• Why RAM and processor's capacity always display less than its actual capacity..Ex 512MB RAM shows 50

  - by Kajal

  Why RAM and processor's capacity always display less than its actual capacity..Ex 512MB RAM shows 506MB..

  Read the article

• Google Sites page never shows up in Google Search organic results?

  - by gus

  I use Google Sites (i.e.: https://sites.google.com/site/EXAMPLE/ ) as a convenient way to maintain up-to-date info on several residential properties, info that's often requested by my property agents, its been around for about 1 year, but I still can never get it to appear in organic Google search results or Bing, even if I search the specific keywords such as the street names. I submitted the URL manually to search engines, knowing that my Sites page probably has very few incoming links. Is this expected behavior? The content of my page has simple formatted text, and outgoing links to Picasa/G+/imgur photo albums. Am I doing something wrong or do all GoogleSites pages have poor organic search rank? Thank you very much.

  Read the article

• When I run Android SDK from terminal, it shows error. How to fix it?

  - by diflame

  Exception in thread "main" java.lang.UnsatisfiedLinkError: no swt-gtk-3550 or swt-gtk in swt.library.path, java.library.path or the jar file at org.eclipse.swt.internal.Library.loadLibrary(Unknown Source) at org.eclipse.swt.internal.Library.loadLibrary(Unknown Source) at org.eclipse.swt.internal.C.<clinit>(Unknown Source) at org.eclipse.swt.internal.Converter.wcsToMbcs(Unknown Source) at org.eclipse.swt.internal.Converter.wcsToMbcs(Unknown Source) at org.eclipse.swt.widgets.Display.<clinit>(Unknown Source) at com.android.sdkmanager.Main.showSdkManagerWindow(Main.java:328) at com.android.sdkmanager.Main.doAction(Main.java:316) at com.android.sdkmanager.Main.run(Main.java:118) at com.android.sdkmanager.Main.main(Main.java:101)

  Read the article

• How to start gkrellm so that it shows up on all virtual desktops?

  - by Jonik

  I'd like to open the GKrellM system monitor so that it is present on all virtual desktops. How to do that? Using Ubuntu 11.04 (Natty) & classic GNOME (not Unity). Bonus questions: How to skip the gkrellm window from the taskbar (on the bottom of the screen)? How to launch it automatically when logging in? (I can ask those separately, too. Or please point out if some of these are already covered.)

  Read the article

• Why RAM and processor's capacity always display less than its actual capacity..Ex 512MB RAM shows 50

  - by Kajal

  Why RAM and processor's capacity always display less than its actual capacity..Ex 512MB RAM shows 506MB..

  Read the article

• Shows how to make your GridViews row-selectable and how to bind to a row's detail.

  How to make an ASP.NET GridView row-selectable and how to bind selected row detail to other controls. The key "trick" to learn is to be able to add an onclick javascript event to each row in the grid that will fire the intrinsic ASP.NET __doPostBack() method.  read moreBy Peter BrombergDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Ubuntu version on external hardrive that shows up in GRUB?

  - by RPi Awesomeness

  I was wondering, is it possible to have Ubuntu installed on an external harddrive and still have it show up in GRUB? Of course, you wouldn't be able boot the other HDD OS unless it was connected, but would this work? I googled 'external HDD OS show in GRUB' and 'have external HDD show up in GRUB' but they didn't bring up anything. Does anyone have any resources to point me to? I can see this as being useful for testing out new releases or having multiple OSs installed without having to go through the BIOS boot choice. Thanks!

  Read the article

• Shows how to use the new Tasks namespace to download multiple documents in parallel.

  In C# 4.0, Task parallelism is the lowest-level approach to parallelization with PFX. The classes for working at this level are defined in the System.Threading.Tasks namespace.  read moreBy Peter BrombergDid you know that DotNetSlackers also publishes .net articles written by top known .net Authors? We already have over 80 articles in several categories including Silverlight. Take a look: here.

  Read the article

• Eclipse shows splash screen and closes. How to fix?

  - by Bozho

  Today I restarted my machine, and Eclipse (3.5, downloaded recently) shows a strange behaviour: shows splash screen for less than a sec quits This is in 100% of the cases, so I can't start Eclipse at all. Where can I find logs about this? I deleted all eclipse resources and re-unzipped it. Same thing. I have enough memory (IntelliJ runs fine), and my anti-virus software doesn't show any activity related to closing eclipse. Any ideas what might have caused this?

  Read the article

• iPhone App that only shows a webpage. Allowed in App Store? [closed]

  - by aioobe

  I'm building a mobile web-app. One of the requirements from my client is that the user should be able to install (through App Store) a program that displays the webpage. I'm thinking of either just displaying a UIWebView with the web-page or opening the webpage in the browser. This would be my first experience with App Store, so I'd like to ask: Would I run into any troubles regarding acceptance in App Store for such "just-show-whatever-the-server-gives-me" application?

  Read the article

• Database design for a media server containing movies, music, tv and everything in between?

  - by user364114

  In the near future I am attempting to design a media server as a personal project. MY first consideration to get the project underway is architecture, it will certainly be web based but more specifically than that I am looking for suggestions on the database design. So far I am considering something like the following, where I am using [] to represent a table, the first text is the table name to give an idea of purpose and the items within {} would be fields of the table. Also not, fid is functional id referencing some other table. [Item {id, value/name, description, link, type}] - this could be any entity, single song or whole music album, game, movie - almost see this as a recursive relation, ie. a song is an item but an album that song is part of is also an item or for example a tv season is an item, with multiple items being tv episodes [Type {id, fid, mime type, etc}] - file type specific information - could identify how code handles streaming/sending this item to a user [Location {id, fid, path to file?}] [Users {id, username, email, password, ...? }] - user account information [UAC {id, fid, acess level}] - i almost feel its more flexible to seperate access control permissions form the user accounts themselves [ItemLog {id, fid, fid2, timestamp}] - fid for user id, and fid2 for item id - this way we know what user access what when [UserLog {id, fid, timestamp}] -both are logs for access, whether login or last item access [Quota {id, fid, cap}] - some sort of way to throttle users from queing up the entire site and letting it download ... Suggestions or comments are welcome as the hope is that this project will be a open source project once some code is laid out.

  Read the article

< Previous Page | 25 26 27 28 29 30 31 32 33 34 35 36  | Next Page >