Search Results

Search found 1541 results on 62 pages for 'ivy bridge'.

Page 3/62 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• KVM-Guests can't get past bridge - no internet connection

  - by tmn29a

  I'm running a backported KVM on a Debian Squeeze. ATM the KVM-Guest can't connect to the internet through the bridge I have set up. The guests can reach each other, the host but nothing outside. I can neither ping, nslookup or do anything to a remote address. The guest are configured to have a static IP. When I didn;t have the bridge but a virtual bridge (the KVM-default) the guest could connect fine. After setting up the bridge things broke, so I think the problem lies there. # The loopback network interface auto lo br0 iface lo inet loopback # Bonding Interface auto bond0 iface bond0 inet static address 10.XXX.XXX.84 netmask 255.255.255.192 network 10.XXX.XXX.64 gateway 10.XXX.XXX.65 slaves eth0 eth1 bond_mode active-backup bond_miimon 100 bond_downdelay 200 bond_updelay 200 iface br0 inet static bridge_ports eth0 eth1 address 172.xxx.xxx.65 broadcast 172.xxx.xxx.127 netmask 255.255.255.192 gateway 172.xxx.xxx.65 bridge_stp on bridge_maxwait 0 Thanks in advance for your help !

  Read the article

• very slow bridge detection

  - by deddihp

  hello everyone, I have setup some bridge interface with 4 ethernet port. My problem is, when they detect some network topology change, the bridge really need a lot of time to have done it. Is there any solution, so the bridge can detect topology change faster ? thanks.

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

• Linux Bridge, Samba netbios name/hostname access

  - by Christopher Wilson

  I am currently running a linux bridge in the following configuration ADSL Modem: 192.168.1.1 Linux Bridge: eth0: 192.168.1.2 eth1: no address Wireless Router: 192.168.0.1 My issue is that i cannot access the "Linux Bridge" shares using the WINS name of the server via client systems (yes i understand it is a transparent bridge but i can access it via the 192.168.1.2 address this is not on the same subnet as the client systems). This is the global section of my SMB.CONF [global] unix extensions = off os level = 20 netbios name = server guest account = nobody server string = 447 Server security = share #unix extensions = no #wins support = yes #wins server = 192.168.0.1 name resolve order = wins lmhosts hosts bcast interfaces bridge1 eth0 eth1 lo bind interfaces only = yes Can i access a bridged server using it's WINS name to access samba shares? Cheers Chris

  Read the article

• Vyatta masquerade out bridge interface

  - by miquella

  We have set up a Vyatta Core 6.1 gateway on our network with three interfaces: eth0 - 1.1.1.1 - public gateway/router IP (to public upstream router) eth1 - 2.2.2.1/24 - public subnet (connected to a second firewall 2.2.2.2) eth2 - 10.10.0.1/24 - private subnet Our ISP provided the 1.1.1.1 address for us to use as our gateway. The 2.2.2.1 address is so the other firewall (2.2.2.2) can communicate to this gateway which then routes the traffic out through the eth0 interface. Here is our current configuration: interfaces { bridge br100 { address 2.2.2.1/24 } ethernet eth0 { address 1.1.1.1/30 vif 100 { bridge-group { bridge br100 } } } ethernet eth1 { bridge-group { bridge br100 } } ethernet eth2 { address 10.10.0.1/24 } loopback lo { } } service { nat { rule 100 { outbound-interface eth0 source { address 10.10.0.1/24 } type masquerade } } } With this configuration, it routes everything, but the source address after masquerading is 1.1.1.1, which is correct, because that's the interface it's bound to. But because of some of our requirements here, we need it to source from the 2.2.2.1 address instead (what's the point of paying for a class C public subnet if the only address we can send from is our gateway!?). I've tried binding to br100 instead of eth0, but it doesn't seem to route anything if I do that. I imagine I'm just missing something simple. Any thoughts?

  Read the article

• Xen HVM Windows 2008 network bridge

  - by JavierMartinz

  I have a problem with the Windows Server 2008 guest (hvm). I can't get a network interface running for him. I also have a Debian guest and it's working ok, but I can't do it with the Win2k8 guest. When I started the VM, the machine freezes and I can't connect by ssh to the host. /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 188.165.B.C netmask 255.255.255.0 network 188.165.B.0 broadcast 188.165.255.255 gateway 188.165.B.254 brctl show bridge name bridge id STP enabled interfaces eth0 8000.e840f20acc28 no peth0 /etc/xen/xend-config.sxp ... (vif-script vif-bridge) (network-script 'network-bridge') ... /etc/xen/win2k8.cfg # Networking # vif = [ 'ip=5.39.F.G,mac=yy:yy:yy:yy:yy:yy,type=ioemu,bridge=eth0' ] /etc/xen/debian.cfg # Networking # vif = [ 'ip=178.33.D.E,mac=xx:xx:xx:xx:xx:xx' ] As you can see, in the Debian guest I only have to specify an IP address and a MAC. But if I put that in the Win2k8 guest, the machine does not start. I am using Xen 4.0

  Read the article

• Ivy via Nexus proxy

  - by Matthias Hryniszak

  Hi, does anyone knows how do I specify in Ivy something like mirror/mirrorOf in Maven? I'm working with a local Maven proxy (Nexus) and need the tool to specify which of the parent repositories should Nexus proxy be accessing. In Maven I do simply: <mirrors> <mirror> <id>central-mirror</id> <mirrorOf>central</mirrorOf> <url>http://localhost:8081/content/repositories/central</url> </mirror> </mirrors> but I can't find this kind of option in Ivy.

  Read the article

• Reporting on release changes when using JIRA, Ivy and SVN

  - by HaveAGuess

  Hey guys, We have an Ivy release procedure where resolve our dependancies using Ivy pre-tagging which means that we can pull in changes for releases by other members of the team that we are not expecting We want to generate reports and track changes to dependancies between releases but there doesn't seem to be an easy way of doing this without a significant effort. We also want to generate a JIRA list of all changes not only in the main project but in dependancies that we own. This is an extension of the problem above. Otherwise we simply don't know what we are releasing - any ideas?!

  Read the article

• Maven/Ivy: Identical artifact with different name in dependency

  - by ThiamTeck

  Currently I am using Ivy for dependency management. And quite often I come across problem of getting identical jar files with different name due to transitive dependency. Example: <dependency> <groupId>javax.mail</groupId> <artifactId>mail</artifactId> <version>1.4</version> </dependency> <dependency> <groupId>org.apache.geronimo.specs</groupId> <artifactId>geronimo-javamail_1.4_spec</artifactId> <version>1.4</version> </dependency> I am thinking of trying out Maven as well. Any best practice to eliminate these identical artifact in either Ivy or Maven?

  Read the article

• openvpn in a bridge?

  - by sebelk

  I have a somewhat tricky proble to solve. We have a wireless link between 2 building. One of them has an mikrotik and below there are some vlans. Some machines of one vlan need to use openvpn to connect to a remote private lan. I put a TP-Link WR1043ND (which those machines connect to) with openwrt with ebtables just in case I need it. I've configured openwrt in such a way that all ports belongs to the same vlan. My idea was to make things as transparent as I can. It has a bridge as follows: usr/sbin/brctl-full show br-lan bridge name bridge id STP enabled interfaces br-lan 8000.f8d111565716 no eth0.1 eth0.2 Also I've added an ebtables rule: ebtables -t broute -A BROUTING -p ipv4 -j DROP So "bridge" has only one IP address. I've installed openvpn and I'm trying to bring up the tunnel but I can't still get working. Sure, someone can says why don't you use the vpn on the mikrotik, there are some reasons, the first one is I have little experience with mikrotik and I'd want to have the vpn at hand :) The problem is that openvpn is not working, because it is complaining that I have only one Ip Address on the server side. So I set up and alias interface with another IP address but is not working either: : Rejected connection attempt from IP-Client-Side:37801 due to --remote setting Is there a way to make it work?

  Read the article

• How to Bridge Two Ethernet Ports on Mac OS X

  - by Rabarberski

  How can I bridge two wired ethernet interfaces on Mac OS X (e.g. the current MacPro comes with two ethernet ports)? Googling turned up (e.g. this Apple forum post and this openvpn post) that this is fairly easy on Linux (using the brctl command) and under Windows (via Network Connections right-click Bridge Connections), but how is it done under Mac OS X? BTW: There also doesn't seem to be a macport for brctl ('port search brctl' didn't turn up any results) Note: I don't want to have 'internet sharing', which creates a new network (by handing out network addresses in a new range). I want to really 'bridge' two interfaces so to keep the same network subnet.

  Read the article

• Bridge and OpenVPN with shorewall

  - by Javier Martinez

  I have this scenario and everything it's working OK, but I want to configure my Shorewall and I can't do it. My interfaces are: br0 (bridge of eth0) tun0 (OpenVPN) vnet* (each one of bridged interfaces with public IP's) Public Main IP: 188.165.X.Y OpenVPN IP's: 172.28.0.x Bridge: public ip's So, I have the next configuration for shorewall: /etc/shorewall/zones #ZONE TYPE OPTIONS IN OUT # OPTIONS OPTIONS fw firewall inet ipv4 road ipv4 /etc/shorewall/interfaces #ZONE INTERFACE BROADCAST OPTIONS inet br0 detect routeback road tun+ detect routeback /etc/shorewall/policy #SOURCE DEST POLICY LOG LIMIT: CONNLIMIT: # LEVEL BURST MASK $FW all ACCEPT inet $FW DROP info road all DROP inet road DROP /etc/shorewall/tunnels #TYPE ZONE GATEWAY GATEWAY # ZONE openvpnserver:1194 inet 0.0.0.0/0 The problem is that even with shorewall running I am able to ping or connect to the virtual machines behind the bridge

  Read the article

• Port forwarding through a client bridge

  - by Gabe Tanenhaus

  I am having a problem with port forwarding with a client bridge. My main router is a 2wire router from AT&T using their firmware. It is a Router/Modem. In my room, there is a Linksys WRT54GL with DD-WRT on it. I have set up the DD-WRT one as a Client bridge for my PC. I can access the internet on my computer using it but when I try and port forward, the ports stay closed. I am port forwarding on my main router (2wire) and it doesn't work. I have checked online and all I see is that I should only need to forward on the main router since the client bridge has NAT disabled, but it seems to not work that way. Any ideas?

  Read the article

• Bridge Intrusion Prevention Vyatta

  - by Steve

  I am trying to create a bridge with ThreatStop, IPS and block a few ports. This bridge will sit in front of my servers. All is working apart from the IPS. I have read the documentation on configuring IPS, I have something configured that it hasn't complained about and nothing is logged so I believe that it isn't working. Is it possible to set-up IPS on a vyatta bridge? Also is it possible to read the logs/events with Snorby? I have also posted this on the Vyatta forums

  Read the article

• bridge to share WiFi internet connection over eth0

  - by rubo77

  In this script there is implemented that you create a mesh network and connect other machines to your device to serve an internet connection with dhcp: echo "starting bridge to share internet connection over eth0" ifconfig eth0 up promisc brctl addbr br-freifunk brctl addif br-freifunk bat0 brctl addif br-freifunk eth0 echo "internet starting, this may take some minutes due to latency..." echo "(use" echo "tail -f /var/log/syslog" echo "in another window for debugging)" echo echo dhclient br-freifunk echo "The error 'Rather than invoking init scripts through /etc/init.d...' can be ignored:" dhclient br-freifunk # without bridge: dhclient bat0 This works fine with the freifunk-mesh network. But how can I serve internet in a normal case? I would like to connect to any open Wifi I find with my network-manager or wicd (yes, with the graphical GUI) and then start a small script that creates a bridge to my network-out on my laptop I use Ubuntu and my networkcards are eth0 and wlan0

  Read the article

• Using the Onboard VGA output with a PCIe video card. Both nVidia

  - by sebikul

  I have 2 video cards, one On board, a nVidia 6150SE nForce 430 and a PCIe nVidia GeForce GT 220 1GB DDR2 RAM I have already configured the PCIe card to use the dual monitor feature, using the VGA and HDMI ports, but now I want to add a third monitor, using the On board VGA port I have managed to enable the On board graphics processor, which is taking 400MB of ram, but I cant manage to use it, nvidia-settings does not detect it, like it's not usable (but is there) My questions are the following: How can I manage to get the On board VGA display to work together with the PCIe graphics card? If possible, how can I recover those 400 MB the on board card is taking (even without being used) or how can I get it to use the PCIe card available memory? System Details: Linux 2.6.35-28-generic i686 Ubuntu 10.10 (All updates installed) NVIDIA Driver Version: 260.19.06 (Official) If more info is needed please let me know. Here is the lspci output when the On board card is disabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) And this is when both are enabled: 00:00.0 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a1) 00:01.0 ISA bridge: nVidia Corporation MCP61 LPC Bridge (rev a2) 00:01.1 SMBus: nVidia Corporation MCP61 SMBus (rev a2) 00:01.2 RAM memory: nVidia Corporation MCP61 Memory Controller (rev a2) 00:01.3 Co-processor: nVidia Corporation MCP61 SMU (rev a2) 00:02.0 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:02.1 USB Controller: nVidia Corporation MCP61 USB Controller (rev a3) 00:04.0 PCI bridge: nVidia Corporation MCP61 PCI bridge (rev a1) 00:05.0 Audio device: nVidia Corporation MCP61 High Definition Audio (rev a2) 00:06.0 IDE interface: nVidia Corporation MCP61 IDE (rev a2) 00:07.0 Bridge: nVidia Corporation MCP61 Ethernet (rev a2) 00:08.0 IDE interface: nVidia Corporation MCP61 SATA Controller (rev a2) 00:09.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0b.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0c.0 PCI bridge: nVidia Corporation MCP61 PCI Express bridge (rev a2) 00:0d.0 VGA compatible controller: nVidia Corporation C61 [GeForce 6150SE nForce 430] (rev a2) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:09.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 08) 02:00.0 VGA compatible controller: nVidia Corporation GT216 [GeForce GT 220] (rev a2) 02:00.1 Audio device: nVidia Corporation High Definition Audio Controller (rev a1) Output of lshw -class display: *-display description: VGA compatible controller product: GT216 [GeForce GT 220] vendor: nVidia Corporation physical id: 0 bus info: pci@0000:02:00.0 version: a2 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:18 memory:df000000-dfffffff memory:c0000000-cfffffff memory:da000000-dbffffff ioport:ef80(size=128) memory:def80000-deffffff *-display description: VGA compatible controller product: C61 [GeForce 6150SE nForce 430] vendor: nVidia Corporation physical id: d bus info: pci@0000:00:0d.0 version: a2 width: 64 bits clock: 66MHz capabilities: pm msi vga_controller bus_master cap_list rom configuration: driver=nvidia latency=0 resources: irq:22 memory:dd000000-ddffffff memory:b0000000-bfffffff memory:dc000000-dcffffff memory:deb40000-deb5ffff If what I'm looking for is not possible, please tell me, so I can disable the On board card and recover those 400MB of wasted RAM Thanks for your help!

  Read the article

• Maven or Ivy for Managing Dependencies from Ant?

  - by Loki

  Hi, I was wondering about the best way to manage projects dependencies from ant. What are the pros and cons of the Maven Ant task and of Ivy?

  Read the article

• Ant: project dependencies in a flat project layout with ivy

  - by MH

  Hello, I have two (Eclipse-) projects. Project A depends on project B, but the projects aren't nested i.e. project A is not a subproject of project B. Apache Ivy is responsible for the dependency management. When I run the compile task in Project A, is there any way to trigger the compile task (in project B) automatically (for example if the jar file of project B doesn't exist)? Thanks a million in advance.

  Read the article

• Gradle/ivy use cached repos?

  - by Misha Koshelev

  Dear All: I would like Grade/Ivy to use cached versions of my jars, as it takes ~20 seconds to check every time for updates. Is this possible? Thank you Misha

  Read the article

• Disable STP in Opensolaris bridge

  - by quentin

  Hello, how can i completely disable STP in a Opensolaris bridge. This bridge is connected to a Cisco Access Port and will disable the uplink port when the first BPDU arrives. bridged[3651]: [ID 581644 daemon.warning] unexpected BPDU on rge1 from 0:xx:xx:xx:xx:b; forwarding disabled I already disabled the transmission of BPDU Messages to the Switch by: dladm set-linkprop -p stp=0 rge1 This solved only the problem that the access switch port goes in "error-disable" mode. Thomas

  Read the article

• Linux : Bridge dont forward if interface is wifi ?

  - by llazzaro

  Hello, I have an edimax (EW-7318USg) which comes with ralink rt73 and its USB. When trying to brigde (to share internet for example) it dont works. But Today I tried to do the same with a wired interface, same bridge, all same steps and I worked (with wired!). Could be that drivers, interface or other thing cant make the bridge with this wifi interface? (this is my question)

  Read the article

• Make Network Manager use bridge for PPPoE instead of only working on ethernet?

  - by Azendale

  My ISP uses PPPoE on their DSL connections. I use Network Manager to connect to this using a bridged modem connected to eth0. Often, I want to test networking things, so a set myself up a KVM machine with a tap interface. I can then connect these interfaces to to virtual 'switches' by adding them to bridges. (I work for my ISP). Sometimes, I want to test cases where the PPPoE is connected more than once. For this, I would like to be able to add eth0 to my 'switch' (a bridge) so the VMs can have a 'bridged modem' connection to the internet. But I would like to still be able to run the PPPoE for my computer at the same time. Which means that I need to get network-manager to run PPPoE over the bridge (or eth0). The problem is that it considers eth0 (and the bridge) 'not managed' by network manager, so it refuses to use it. So, how can I have network manager dial PPPoE over a bridge?

  Read the article

• KVM work with bridge network problems

  - by isware

  I try to configure bridge network for KVM(refer to http://www.linux-kvm.org/page/Networking), and it worked for Guest OS, but I have two problems with my Fedora host OS: 1?I can not access internet on host 2?The bridge configuration lost after reboot, I need to execute "service network restart" again to bring it up I checked here(http://serverfault.com/questions/168119/kvm-network-bridge-with-public-static-ip-for-both-host-and-guests) for the first problem, it seems not working for me. Any advice is appreciated! ifconfig -a eth0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:231340 errors:0 dropped:0 overruns:0 frame:0 TX packets:413424 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:15335606 (14.6 MiB) TX bytes:114755796 (109.4 MiB) Interrupt:44 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:119307 errors:0 dropped:0 overruns:0 frame:0 TX packets:119307 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:57151264 (54.5 MiB) TX bytes:57151264 (54.5 MiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) sw0 Link encap:Ethernet HWaddr 48:5B:39:ED:EB:5A inet addr:192.168.1.133 Bcast:255.255.255.255 Mask:255.255.255.0 inet6 addr: fe80::4a5b:39ff:feed:eb5a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:229584 errors:0 dropped:0 overruns:0 frame:0 TX packets:401232 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:11047463 (10.5 MiB) TX bytes:113891533 (108.6 MiB) tap0 Link encap:Ethernet HWaddr F2:86:1A:48:E2:55 inet6 addr: fe80::f086:1aff:fe48:e255/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232 errors:0 dropped:0 overruns:0 frame:0 TX packets:2744 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:24842 (24.2 KiB) TX bytes:243899 (238.1 KiB) virbr0 Link encap:Ethernet HWaddr 9A:7C:09:6B:85:65 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:46 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:5513 (5.3 KiB)

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >