Search Results

Search found 1541 results on 62 pages for 'ivy bridge'.

Page 4/62 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• how to setup a bridge with 2 NICs and few virtual machines

  - by Bond

  Here is my situation. I have a server with 2 NICs. I have installed virtual box and I have created a few Guest Operating Systems on it. I want these Virtual Machines to be using a bridge.NIC2 would be used to setup this bridge and NIC1 would be connected to corporate network.I am not clear with how should I go on doing this. /etc/network/interfaces is the file which I am trying to modify etc. My approach is following 1) Define a configuration file /etc/network/interfaces 2) Create IPTABLES as how NIC1 will forward the packets to Bridge on NIC2 Now comes the problem I do not understand what is the meaning of following lines in the configuration file auto lo iface lo inet loopback # The primary network interface auto eth2 iface eth2 inet manual auto br0 iface br0 inet static address 192.168.1.14 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.10 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 192.168.13.2 dns-search myserver.net bridge_ports eth2 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off So any pointers to what should be the entries of /etc/network/interfaces file. So that I understand which parameter is to be used when and where that would help me.

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• CentOS 6.2 Bridge Setup for KVM

  - by Gaia

  I'm trying to set up bridged networking with KVM on CentOS 6.2 to no avail. There are plenty of docs and tutorials about it, but they all seem to conflict or don't provide info specific enough to my situation. I just don't get it. I access the host via public IP "xxx.xxx.128.58". All other available IPs (/29) should be bridged and made available to the only KVM guest (running a public facing LAMP stack) that will be setup on this machine. The amazingly unhelpful NOC people assigned the extra IPs to eth1. Is this correct? Should br0 bridge to eth0 or eth1? How do I set this up? Here is the relevant info: eth0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BC inet6 addr: fe80::225:90ff:fe68:febc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:763 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:550811 (537.9 KiB) TX bytes:648 (648.0 b) Memory:fb980000-fba00000 eth1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.58 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 inet6 addr: fe80::225:90ff:fe68:febd/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1806 errors:0 dropped:0 overruns:0 frame:0 TX packets:1505 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:133166 (130.0 KiB) TX bytes:106070 (103.5 KiB) Memory:fb900000-fb980000 eth1:0 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.59 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:1 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.60 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:2 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.61 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 eth1:3 Link encap:Ethernet HWaddr 00:25:90:68:FE:BD inet addr:xxx.xxx.128.62 Bcast:xxx.xxx.128.63 Mask:255.255.255.248 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Memory:fb900000-fb980000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) virbr0 Link encap:Ethernet HWaddr 52:54:00:62:55:68 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=XXXX.domain.com > brctl show bridge name bridge id STP enabled interfaces br0 8000.00259068febc no eth0 virbr0 8000.525400625568 yes virbr0-nic > ls -fl | grep ifcfg -rw-r--r-- 1 root root 198 Jun 7 10:58 ifcfg-eth0 -rw-r--r--. 1 root root 254 Oct 7 2011 ifcfg-lo -rw-r--r-- 1 root root 77 Jun 6 18:51 ifcfg-eth1-range0 -rw-r--r-- 1 root root 168 Jun 6 18:50 ifcfg-eth1 > cat ifcfg-eth0 DEVICE="eth0" BOOTPROTO="static" BRIDGE="br0" HWADDR="00:25:90:68:FE:BC" IPV6INIT="yes" MTU="1500" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" IPADDR="yyy.yyy.216.131" NETMASK="255.255.255.128" > cat ifcfg-eth1 DEVICE="eth1" HWADDR="00:25:90:68:FE:BD" NM_CONTROLLED="yes" ONBOOT="yes" BOOTPROTO="static" IPADDR="xxx.xxx.128.58" NETMASK="255.255.255.248" GATEWAY="xxx.xxx.128.57" > cat ifcfg-eth1-range0 IPADDR_START="xxx.xxx.128.59" IPADDR_END="xxx.xxx.128.62" CLONENUM_START="0" Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xxx.xxx.128.56 * 255.255.255.248 U 0 0 0 eth1 192.168.122.0 * 255.255.255.0 U 0 0 0 virbr0 link-local * 255.255.0.0 U 1003 0 0 eth1 default xxx.xxx.128.57 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Wireless Bridge with NetGear and TP-Link

  - by Tiago Cruz

  I have a wireless NetGear WGR614 v7 (little old) router connected to the internet, but I can't get a good signal in the other end of my house. I have another new one, model TP-Link TL-WR941ND wireless router. I was able to do the stuff works using a wired cable, but now, I would like to do the same using wireless connections (bridge mode, some like WDS?) Now, the computer connected to TP LINK was able to ping my computer connected to NETGEAR, but we cannot go IP ADDRESS outside my network, only internals ones. What can I do to configure this? Is needed that BOTH wireless routers support BRIDGE mode or only one its good enough? Thanks a lot!!

  Read the article

• How do I turn a router into a wireless bridge

  - by Rob Cowell

  I'm trying to get my HD satellite receiver connected to the internet - it has an Ethernet port on the back but my networking equipment is all upstairs. I had the idea of connecting a spare wireless router to the box with an ethernet cable and getting that wireless router to talk to my "main" wireless router (the one with the ADSL connection) to supply internet access. I believe this entails getting the router to work as a "wireless bridge", but I don't know how to do this. Currently, the ADSL line is hooked up to a NETGEAR DG834G. The other two "spare" wireless routers I have to act as the bridge are :- Huawei HG520b Netgear DGN2000 BT Homehub I'd prefer not to change the "main" router (cos I'm used to its web admin UI) - does anyone know a way I can achieve the connectivity I require with the equipment I have?

  Read the article

• How do I turn a router into a wireless bridge

  - by Rob Cowell

  I'm trying to get my HD satellite receiver connected to the internet - it has an Ethernet port on the back but my networking equipment is all upstairs. I had the idea of connecting a spare wireless router to the box with an ethernet cable and getting that wireless router to talk to my "main" wireless router (the one with the ADSL connection) to supply internet access. I believe this entails getting the router to work as a "wireless bridge", but I don't know how to do this. Currently, the ADSL line is hooked up to a NETGEAR DG834G. The other two "spare" wireless routers I have to act as the bridge are :- Huawei HG520b Netgear DGN2000 BT Homehub I'd prefer not to change the "main" router (cos I'm used to its web admin UI) - does anyone know a way I can achieve the connectivity I require with the equipment I have?

  Read the article

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Role of a bus bridge

  - by Wayne

  Simple question: What is the role of a bus bridge?

  Read the article

• wireless repeater vs wireless bridge?

  - by Kossel

  Scenario: I have a ADSL modem inside the studio which is connected with some wired/wireless devices. but when I'm in the backyard with my laptop the wireless signal is very poor, so the connection is very unstable. I have an old belkin wireless router and I read that it can be useful in this scenario. after some search, it's compatible with DD-WRT, and seems setting it both wireless repeater or wireless bridge can do the job. but which is better for speed and stability or for my purpose they are the same? wireless repeater wireless bridge

  Read the article

• After connecting wlan0 to bridge interface (and then removing it), can't connect to AP

  - by gmonk

  I'm on a laptop running Debian Jessie with kernel 3.13-1-amd64; lspci shows that my wireless NIC + driver is 04:00.0 Network controller: Intel Corporation Wireless 3160 (rev 83) Subsystem: Intel Corporation Dual Band Wireless-AC 3160 Kernel driver in use: iwlwifi This has been working without any problems, until I tried creating a bridge for lxc containers to use. I did the same thing as this person here: How-to set up a network bridge on a laptop for LXC use? -- and ended up having the same problem as this poster did, so I decided to "undo" my actions. This hasn't been successful. Actions taken so far: To configure the bridge: #> ip link add type veth #> iw dev wlan0 set 4addr on #> ifconfig veth0 up #> brctl addbr br0 #> brctl addif br0 wlan0 #> brctl addif br0 veth0 #> ifconfig br0 192.168.0.4/24 #> ifconfig wlan0 0.0.0.0 To "deconfigure": #> brctl delif br0 wlan0 #> brctl delif br0 veth0 #> iw dev wlan0 set 4addr off #> ifconfig veth0 down #> ifconfig wlan0 down #> ifconfig br0 down #> brctl delbr br0 Now, dmesg and /var/log/syslog show repeated attempts at connecting to the AP that was working before, which fail after authentication: May 27 09:16:01 myhostname kernel: [11350.757172] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:01 myhostname kernel: [11350.759036] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:01 myhostname kernel: [11350.762615] wlan0: authenticated May 27 09:16:01 myhostname kernel: [11350.762753] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.762755] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:01 myhostname kernel: [11350.765080] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:01 myhostname kernel: [11350.767474] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:01 myhostname kernel: [11350.767476] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:01 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:01 myhostname kernel: [11350.788475] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:01 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:02 myhostname dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 14 May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname kernel: [11354.559579] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.561458] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> associating May 27 09:16:04 myhostname kernel: [11354.563445] wlan0: authenticated May 27 09:16:04 myhostname kernel: [11354.563631] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.563633] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:04 myhostname kernel: [11354.565727] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:04 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:04 myhostname kernel: [11354.568091] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:04 myhostname kernel: [11354.569030] wlan0: associated May 27 09:16:04 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:05 myhostname kernel: [11354.978204] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:05 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:05 myhostname kernel: [11354.992729] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:05 myhostname kernel: [11354.995004] cfg80211: World regulatory domain updated: May 27 09:16:05 myhostname kernel: [11354.995005] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:05 myhostname kernel: [11354.995006] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995007] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995008] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995009] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:05 myhostname kernel: [11354.995010] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:05 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.763968] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:09 myhostname kernel: [11358.765796] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:09 myhostname kernel: [11358.769957] wlan0: authenticated May 27 09:16:09 myhostname kernel: [11358.770102] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770104] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:09 myhostname kernel: [11358.770846] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:09 myhostname kernel: [11358.773358] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=12 aid=0) May 27 09:16:09 myhostname kernel: [11358.773361] wlan0: 00:18:f8:54:a3:d6 denied association (code=12) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:09 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-ASSOC-REJECT bssid=00:18:f8:54:a3:d6 status_code=12 May 27 09:16:09 myhostname kernel: [11358.802187] wlan0: deauthenticating from 00:18:f8:54:a3:d6 by local choice (reason=3) May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> disconnected May 27 09:16:09 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: SME: Trying to authenticate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.573442] wlan0: authenticate with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.575270] wlan0: send auth to 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> authenticating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Trying to associate with 00:18:f8:54:a3:d6 (SSID='myaccesspoint' freq=2437 MHz) May 27 09:16:12 myhostname kernel: [11362.580334] wlan0: authenticated May 27 09:16:12 myhostname kernel: [11362.580503] iwlwifi 0000:04:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.580516] iwlwifi 0000:04:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP May 27 09:16:12 myhostname kernel: [11362.583508] wlan0: associate with 00:18:f8:54:a3:d6 (try 1/3) May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: authenticating -> associating May 27 09:16:12 myhostname wpa_supplicant[8946]: wlan0: Associated with 00:18:f8:54:a3:d6 May 27 09:16:12 myhostname kernel: [11362.585908] wlan0: RX AssocResp from 00:18:f8:54:a3:d6 (capab=0x411 status=0 aid=9) May 27 09:16:12 myhostname kernel: [11362.586781] wlan0: associated May 27 09:16:12 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associating -> associated May 27 09:16:13 myhostname kernel: [11362.947693] wlan0: deauthenticated from 00:18:f8:54:a3:d6 (Reason: 15) May 27 09:16:13 myhostname wpa_supplicant[8946]: wlan0: CTRL-EVENT-DISCONNECTED bssid=00:18:f8:54:a3:d6 reason=15 May 27 09:16:13 myhostname kernel: [11362.973461] cfg80211: Calling CRDA to update world regulatory domain May 27 09:16:13 myhostname kernel: [11362.975673] cfg80211: World regulatory domain updated: May 27 09:16:13 myhostname kernel: [11362.975675] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) May 27 09:16:13 myhostname kernel: [11362.975676] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975677] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975678] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm) May 27 09:16:13 myhostname kernel: [11362.975679] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: associated -> disconnected May 27 09:16:13 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: disconnected -> scanning May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0/wireless): association took too long. May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: config -> failed (reason 'no-secrets') [50 120 7] May 27 09:16:14 myhostname NetworkManager[13992]: <info> Marking connection 'Auto myaccesspoint' invalid. May 27 09:16:14 myhostname NetworkManager[13992]: <warn> Activation (wlan0) failed for connection 'Auto myaccesspoint' May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): device state change: failed -> disconnected (reason 'none') [120 30 0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): deactivating device (reason 'none') [0] May 27 09:16:14 myhostname NetworkManager[13992]: <info> (wlan0): supplicant interface state: scanning -> disconnected The things that jump out at me are "deauthenticating ... by local choice( reason=3)" and the lines that contain "(reason=15)". I've tried various fixes: iwconfig wlan0 power off killing wpa_supplicant connecting with iwconfig + dhclient instead of gnome's network -manager explicitly configuring wlan0 in /etc/network/interfaces creating a /etc/wpa_supplicant.conf file ...but nothing seems to work. I'm not sure what I did wrong, or what step I've skipped in trying to get wlan0 back as a non-bridged device -- I removed it from the bridge and then deleted the bridge itself. Any ideas?

  Read the article

• Wireless Bridge -DHCP

  - by Usta

  I was thinking of picking up a couple of TP-Link wireless routers, and setting them to bridge. I have a sep. LAN network that would have one of them, and I'd put one on my internet connection. Would I be able to keep my current IP subnets? (255.255.255.0 and 255.0.0.0) or would I have to pull my IPs from the same IP range. (I want to keep my current DHCP servers in place) The reason I want a bridge is so that I can VPN into the internal network.

  Read the article

• Synergy over a LAN bridge in Windows 7 64-bit, connection timing out

  - by bmozzy

  I haven't seen a question like this anywhere, so I hope it isn't a duplicate. Anyway, I have two computers, and one of them has its network connection through a LAN bridge in the other, which goes to a router. I want to set them up so that the one with the bridge is the server, and the other is the client. I followed the instructions to get everything set up, and the client keeps saying that the connection timed out. Here are screenshots of Synergy running on the server and client, as well as one of the server's configuration. Thanks in advance for the help!

  Read the article

• PHP/Java Bridge java.lang.NoSuchMethodException

  - by m1sk

  I have setup PHP/Java Bridge with working examples in netbeans tomcat directory. What doesnt work is using custom JAR Here is my code: package com.micha; public class Hello1Bean { public Hello1Bean() {} String hi() {return "This is my hello message";} String hello(String name) {return "Hello" + name;} } And the php code <!DOCTYPE html> <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=UTF-8"> <title></title> </head> <body> <?php require_once ("java/Java.inc"); $world = new Java("com.micha.Hello1Bean"); echo java_values($world->hi()); echo "Hello Working Thingy\n\n"; ?> </body> </html> When I check http://localhost:8084/JavaBridge/mytest.php: javax.servlet.ServletException: java.lang.RuntimeException: PHP Fatal error: Uncaught [[o:Exception]:"java.lang.Exception: Invoke failed: [[o:Hello1Bean]]->hi. Cause: java.lang.NoSuchMethodException: hi(). Candidates: [] VM: 1.6.0_25@http://java.sun.com/" at: #-6 php.java.bridge.JavaBridge.checkM(JavaBridge.java:1085) #-5 php.java.bridge.JavaBridge.Invoke(JavaBridge.java:1024) #-4 php.java.bridge.Request.handleRequest(Request.java:417) #-3 php.java.bridge.Request.handleRequests(Request.java:500) #-2 php.java.bridge.http.ContextRunner.run(ContextRunner.java:145) #-1 php.java.bridge.ThreadPool$Delegate.run(ThreadPool.java:60) #0 C:\Users\Micha\.netbeans\7.1.2\apache-tomcat-7.0.22.0_base\webapps\JavaBridge\java\Java.inc(232): java_ThrowExceptionProxyFactory->getProxy(2, 'com.micha.Hello...', 'T', true) #1 C:\Users\Micha\.netbeans\7.1.2\apache-tomcat-7.0.22.0_base\webapps\JavaBridge\java\Java.inc(360): java_Arg->getResult(true) #2 C:\Users\Micha\.netbeans\7.1.2\apache-tomcat-7.0.22.0_base\webapps\JavaBridge\java\Java.inc(366): java_Client->getWrappedResult(true) #3 C:\Users\Micha\.netbean in C:\Users\Micha\.netbeans\7.1.2\apache-tomcat-7.0.22.0_base\webapps\JavaBridge\java\Java.inc on line 195 php.java.servlet.fastcgi.FastCGIServlet.handle(FastCGIServlet.java:499) php.java.servlet.fastcgi.FastCGIServlet.doGet(FastCGIServlet.java:521) javax.servlet.http.HttpServlet.service(HttpServlet.java:621) javax.servlet.http.HttpServlet.service(HttpServlet.java:722) org.netbeans.modules.web.monitor.server.MonitorFilter.doFilter(MonitorFilter.java:393) php.java.servlet.PhpCGIFilter.doFilter(PhpCGIFilter.java:126) Before I had a ClassNotFoundException so it knows there is a a class but for some odd reason I cant call the function. ( if I replace "com.micha.Hello1Bean" with some class that doesnt exist then I get that exception)

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Ubuntu Laptop as a wireless hotspot on bridge mode

  - by nixnotwin

  I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

  Read the article

• Bridging two wireless interfaces with brctl?

  - by AK_

  I have this topology: [internet] ^ L-------[wlan0]-[host]-[wlan1]-----[client-1] I tried to bridge wlan0 wlan1 but it wont work with brctl; but magically when I issue this command #iw set dev wlan0 4addr on it adds wlan0 to the bridge BUT I lost all internet connection and I was unable to hook it to the internet router. can somebody please explain why did that happen and is there a way to get this done ?

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• KVM network bridge and public static IP for both host and guests

  - by Javier Martinez

  I have a Debian Server with 4 public static addresses. There is a KVM guest (also Debian) installed and running. What I want is to give the guest an IP of the host, so that both machines have public IPs. IP 1: 188.165.A.B IP 2: 178.33.CCC.D IP 3: 178.33.CCC.E IP 4: 178.33.CCC.F What should I do to have connection for host and guest ? This is network conf: # ifconfig br0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:188.165.A.B Bcast:188.165.255.255 Mask:255.255.255.0 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3618 errors:0 dropped:4 overruns:0 frame:0 TX packets:4853 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:599562 (585.5 KiB) TX bytes:1693443 (1.6 MiB) eth0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet6 addr: fe80::ea40:f2ff:fe0a:cc28/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4274 errors:0 dropped:0 overruns:0 frame:0 TX packets:4879 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:720045 (703.1 KiB) TX bytes:1715641 (1.6 MiB) Interrupt:20 Memory:fe500000-fe520000 eth0:0 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.D Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:1 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.E Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 eth0:2 Link encap:Ethernet HWaddr e8:40:f2:0a:cc:28 inet addr:178.33.CCC.F Bcast:178.33.255.255 Mask:255.255.255.255 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:27932 errors:0 dropped:0 overruns:0 frame:0 TX packets:27932 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1820862 (1.7 MiB) TX bytes:1820862 (1.7 MiB) vnet0 Link encap:Ethernet HWaddr fe:54:00:87:40:ec inet6 addr: fe80::fc54:ff:fe87:40ec/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:1452 (1.4 KiB) TX bytes:16958 (16.5 KiB) #route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default aa.bb.cc.eu 0.0.0.0 UG 0 0 0 br0 188.165.255.0 * 255.255.255.0 U 0 0 0 br0 # brctl show bridge name bridge id STP enabled interfaces br0 8000.e840f20acc28 no eth0 vnet0 There is no firewall enabled and DNS is configured properly. What I want to achieve: | | | +----+-------------------------+-+------+ | | Host | | | | | | | | | | +------------+------+ | | eth0 | eth0:0-1 | | | 188.165.A.B | | | | | | | | | br0 vnet0 | | | +------------+------+ | | | | | | | | +------------+------+ | | | | | | | | eth0:2-+ | | | | 178.33.CCC.F | | | | | | | | Guest | | | +-------------------+ | +---------------------------------------+ Thanks you

  Read the article

• very slow bridge detection

  - by deddihp

  hello everyone, I have setup some bridge interface with 4 ethernet port. My problem is, when they detect some network topology change, the bridge really need a lot of time to have done it. Is there any solution, so the bridge can detect topology change faster ? thanks.

  Read the article

• Motorola NVG510 bridge mode

  - by Blacklight Shining

  I have a Motorola NVG510 modem from AT&T, and I would like to disable all routing functions and use it as just a modem. I have a Time Capsule that's already connected and broadcasting its own wireless network, which is how I've been connecting (it's been reporting a double-NAT error, which I assume is from the NVG510 also acting as a router). I followed the instructions in question six here, and I can connect as I did before, but my Time Capsule still has a double-NAT error. How do I put the NVG510 into bridge mode or otherwise fix the double-NAT error? (No, ignoring it does not count as a fix.)

  Read the article

• debian lenny xen bridge networking problem

  - by Sasha

  DomU isn't talking to the world, but it talks to Dom0. Here are the tests that I made: Dom0 (external networking is working): ping 188.40.96.238 #Which is Domu's ip PING 188.40.96.238 (188.40.96.238) 56(84) bytes of data. 64 bytes from 188.40.96.238: icmp_seq=1 ttl=64 time=0.092 ms DomU: ping 188.40.96.215 #Which is Dom0's ip PING 188.40.96.215 (188.40.96.215) 56(84) bytes of data. 64 bytes from 188.40.96.215: icmp_seq=1 ttl=64 time=0.045 ms ping 188.40.96.193 #Which is the gateway - fail PING 188.40.96.193 (188.40.96.193) 56(84) bytes of data. ^C --- 188.40.96.193 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1013ms The system is debian lenny with a normal setup. Here is my configs: uname -a Linux green0 2.6.26-2-xen-686 #1 SMP Wed Aug 19 08:47:57 UTC 2009 i686 GNU/Linux cat /etc/xen/green1.cfg |grep -v '#' kernel = '/boot/vmlinuz-2.6.26-2-xen-686' ramdisk = '/boot/initrd.img-2.6.26-2-xen-686' memory = '2000' root = '/dev/xvda2 ro' disk = [ 'file:/home/xen/domains/green1/swap.img,xvda1,w', 'file:/home/xen/domains/green1/disk.img,xvda2,w', ] name = 'green1' vif = [ 'ip=188.40.96.238,mac=00:16:3E:1F:C4:CC' ] on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' ifconfig eth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet addr:188.40.96.215 Bcast:188.40.96.255 Mask:255.255.255.192 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3296 errors:0 dropped:0 overruns:0 frame:0 TX packets:2204 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:262717 (256.5 KiB) TX bytes:330465 (322.7 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) peth0 Link encap:Ethernet HWaddr 00:24:21:ef:2f:86 inet6 addr: fe80::224:21ff:feef:2f86/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:3407 errors:0 dropped:657431448 overruns:0 frame:0 TX packets:2291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:319941 (312.4 KiB) TX bytes:338423 (330.4 KiB) Interrupt:16 Base address:0x8000 vif2.0 Link encap:Ethernet HWaddr fe:ff:ff:ff:ff:ff inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1 RX packets:27 errors:0 dropped:0 overruns:0 frame:0 TX packets:151 errors:0 dropped:33 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1164 (1.1 KiB) TX bytes:20974 (20.4 KiB) ip a s 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: peth0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 4: vif0.0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 5: veth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 6: vif0.1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 7: veth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 8: vif0.2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 9: veth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 10: vif0.3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff 11: veth3: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN link/ether 00:00:00:00:00:00 brd ff:ff:ff:ff:ff:ff 12: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN link/ether 00:24:21:ef:2f:86 brd ff:ff:ff:ff:ff:ff inet 188.40.96.215/26 brd 188.40.96.255 scope global eth0 inet6 fe80::224:21ff:feef:2f86/64 scope link valid_lft forever preferred_lft forever 14: vif2.0: <BROADCAST,MULTICAST,PROMISC,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 32 link/ether fe:ff:ff:ff:ff:ff brd ff:ff:ff:ff:ff:ff inet6 fe80::fcff:ffff:feff:ffff/64 scope link valid_lft forever preferred_lft forever brctl show bridge name bridge id STP enabled interfaces eth0 8000.002421ef2f86 no peth0 vif2.0 ip r l Dom0: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.215 default via 188.40.96.193 dev eth0 DomU: 188.40.96.192/26 dev eth0 proto kernel scope link src 188.40.96.238 default via 188.40.96.193 dev eth0

  Read the article

• Using airport extreme base station as a wireless G to wireless N bridge

  - by micmcg

  Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

  Read the article

• How to bridge multiple wireless access points (and internet entry points) into one network

  - by amccormack

  I have two DSL lines coming in to wireless access points and then running to a RV082 Gateway/Bridge. The gateway then runs to a switch, which runs to multiple PCs and a Printer (See picture below). Normally, I would set up the wireless access points behind the gateway, but they are also the modems for the dsl. I have found that I can not print to the network printer if I am connected to the wireless network, but only if I am connected to the wired network. How can I configure the Gateway and APs (Routers) so that the PCs and Printer are all on the same internal network? I have tried turning DHCP off or redirect on the APs and redirect them to the Gateway. However, neither of these worked. Furthermore, I tried pinging the Gateway from the AP but got no response.

  Read the article

• Linksys WRT54Gx as Repeater Bridge

  - by Robert Koritnik

  I have a Linksys WRT54Gx router with DD-WRT software working fine. But. Is it possible to use it as a Repeater Bridge when the host router isn't configured to be in the default 192.168.1.1 subnet? I've set everything from these instructions. I've also tried setting repeater router's IP address to be inside host's subnet, setting Gateway + DNS IP addresses... But It still didn't work. Client machines connecting to second router (my Linksys) were configured to use DHCP and also static IPs within host's subnet. Nothing worked. Can anyone tell me how to configure it to make it work?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >