Search Results

Search found 19125 results on 765 pages for 'hard disk'.

Page 32/765 | < Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >

  • How to remove file permissions from an external hard drive?

    - by user2540416
    My macbook recently died and I am currently trying to figure out how to copy my data. What I did was, I took out the hard drive, put it in an enclosure and plugged it in to my other laptop that runs linux. The problem is, I cannot copy files from the hard drive due to file permissions. I tried to access the hard drive as root. But I still cannot copy files. How do I remove file permissions from the harddrive?

    Read the article

  • Can't access my accelerated hard disk from msdos after installing linux on ssd cache

    - by Chibueze Opata
    I mistakenly installed Ubuntu on my ssd (forgot my PC actually came with one), when it detected a ~31GiB disk that it wanted to install to, I was a bit confused since I had brought out 30Gb in my primary disk for it, but I clicked continue. After installation, I tried to boot back into my Windows and it brought out some Intel Raid Disk Utility stuff saying I should disable acceleration on a disk something couldn't be found, I canceled it but whatever I tried, recovery tools, setups etc, I couldn't just access the drive which was apparently using the SSD as cache. Since then I've been stuck. I tried setting the 'raid' flag to the disk from 'gParted', still I couldn't. I tried the diskraid utility from windows recover disk, it said it couldn't detect any raid, diskpart sees the partition but doesn't see the volume, when I remove the raid flag, it sees the volume as one of raw type, and I can't access anything. I can however mount the drive from terminal in Ubuntu and access my files, but I don't have any backup media at the moment so I can do a factory re-install. Please how do I go about solving the issue, precisely I would like to know how to boot into the drive again. Thanks!

    Read the article

  • Best Easiest Fastest No Install USB Boot Disk in 4 Simple Steps :)

    - by PearlFactory
    USB Boot Disk When you look how to create USB Boot Disk on the web it is a nightmare   Here is the easiest I use that works for all MS prods At a computer running Windows Vista, Windows 7, or Windows Server 2008, run a command prompt as administrator and execute the following: Make Sure you have all explorer windows closed and nothing referencing the USB i.e a doc open in Word 1. C:\> diskpart DISKPART> list disk [Identify disk # of the USB key] DISKPART> sel disk 1 [assuming 1 was the # from above] DISKPART> clean [CAUTION—will wipe whichever disk is selected] DISKPART> cre part pri DISKPART> active DISKPART> assign DISKPART> format fs=ntfs quick DISKPART> exit C:\> exit 2. Copy the contents of the Windows Server 2008 R2 or any other MS OS  DVD/ISO to the USB key. 3. From the system tray, use the “Safely remove hardware” icon to safely remove the USB key from the computer. This helps ensure that all files have been fully written to the USB key. (Especially after the large file copy) 4. Restart,,,put usb in and Find reference from HP h20195.www2.hp.com/v2/GetPDF.aspx/4AA3-1317ENW.pdf

    Read the article

  • Can't boot Ubuntu 12.04 from external Hard Drive using Mac

    - by Catgirl the Crazy
    Recently, I upgraded the RAM and hard drive on my Early 2008 Macbook to improve the performance. Rather than throw away the old hard drive, I bought an enclosure for it to turn it into an external hard drive, and, since all the data was migrated to my new drive, I decided to install Ubuntu on it for funsies (note: I am a near-total Ubuntu n00b). My first attempt to install Ubuntu didn't work (it gave me errors about not being able to find the BIOS or something), but my second attempt finished successfully (can't remember what, if anything, I did different). However, when I plug the external drive into my Macbook, it gives me a message saying it can't read the disk. Moreover, when I go into the Startup Manager (i.e.: what you get when you turn on the Macbook while holding the option key), the external drive is not one of the available startup disks. I thought this might be because I have an older Macbook, so I tried booting it with my mom's Late 2011 Macbook, and got the same results. Then I tried booting it through my dad's Dell laptop that runs Windows 7, and that time it worked. This is really counter intuitive to me, since the hard drive originally came from a Macbook, so if anything you'd think it would be less compatible with the Windows laptop than the Macbook. In case it helps, here's a link to a picture of how I set up the partition table while doing the install (not shown there is the fact that I checked the "Format?" box next to the /boot partition, since it gave me a warning when I tried to continue the installation without doing so) Anyone have any clue at all? If it helps, the hard drive I'm using is a 120GB 5400-rpm Serial ATA hard disk drive.

    Read the article

  • Spinup time failure

    - by bioShark
    I am not sure this is a real question or a bug I should report Ubuntu. Using: Ubuntu 11.10, on a Intel Q6600, Samsung Spinpoint F4 2TB. I have set my PC on Suspend and after I came back, pressed Enter and after logging in everything was back to normal. However, I had a message from Disk Utility that one disk reports errors. I entered Disk Utility, and my Samsung 2TB disk, the one on which my Ubuntu is installed, had the SMART Status turned red, with error message on it. The error was: Spinup time failed Value 21, Threshold value was 25 (so the error was reported because 21 < 25) I restarted and booted up in Windows to see what HD Tune is reporting. Unfortunately it was exactly the same 21/25. After reading up on Wiki about SMART and the errors, I discovered that Spinup time is the time required for the disk to reach full spinning speed in milliseconds. Then it hit me that, in Ubuntu I had Suspended the system, making essentially all my hardware stop. And when I rebooted to Windows, the hardware doesn't really stop, so SMART's reading of the Spinup time was still from Ubuntu's suspension. So I did a full PC stop and then booted up again, both in Ubuntu and Windows to see if there are different readings. Both reported successful Spinup time, 68 (a little better then 21 :) ), although in Disk Utility I have a nice message: Failed in the Past So now I am pretty sure that Ubuntu didn't handle the Suspend correctly, but then again should I worry about Imminent hardware failure ? Am I missing some drivers? Should I report this as a bug to Ubuntu? Sorry if this was a bad place to ask this question.

    Read the article

  • How to mount an external HDD?

    - by Slash
    I have Ubuntu Linux 12.04 version the latest right now.I want to mount an external HDD NTFS 1TB.I have followed many guides but still no success.The error I'm getting is this: Failed to read last sector (1953523119): Invalid argument HINTS: Either the volume is a RAID/LDM but it wasn't setup yet, or it was not setup correctly (e.g. by not using mdadm --build ...), or a wrong device is tried to be mounted, or the partition table is corrupt (partition is smaller than NTFS), or the NTFS boot sector is corrupt (NTFS size is not valid). Failed to mount '/dev/sdb1': Invalid argument The device '/dev/sdb1' doesn't seem to have a valid NTFS. Maybe the wrong device is used? Or the whole disk instead of a partition (e.g. /dev/sda, not /dev/sda1)? Or the other way around? Using Storage Device MAnager i get this error:Error mounting: mount exited with exit code 1: helper failed with: mount: only root can mount /dev/sdb1 on /media/Skliros_Diskos {external disk name} When I use sudo fdisk -l, this is the output: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000e0bc6 Device Boot Start End Blocks Id System /dev/sda1 * 2048 618854399 309426176 83 Linux /dev/sda2 618856446 625141759 3142657 5 Extended /dev/sda5 618856448 625141759 3142656 82 Linux swap / Solaris Disk /dev/sdb: 1000.2 GB, 1000202043392 bytes 255 heads, 63 sectors/track, 121600 cylinders, total 1953519616 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002093a Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 7 HPFS/NTFS/exFAT

    Read the article

  • Raid Shows Up as Multiple Drives - Can't Mount

    - by manyxcxi
    I have a single hard drive that the OS is installed on and I have Sil raid card installed with two matching 500GB hdds set up in Raid 0 and formatted- they're completely empty. For whatever reason they are showing up as /dev/sdb and /dev/sdc and not as a single hard drive. I used fdisk to format both raid drives as Linux raid auto (fd) but I cannot mount either device and dmraid doesn't seem to want to work, what step am I missing? When I installed 9.04 oh so long ago it seems like it recognized and automatically did everything that needed to be done, now I'm stuck. dmraid Output root@tripoli:~# dmraid -r /dev/sdc: sil, "sil_biaebhadcfcb", stripe, ok, 976771072 sectors, data@ 0 /dev/sdb: sil, "sil_biaebhadcfcb", stripe, ok, 976771072 sectors, data@ 0 root@tripoli:~# dmraid -ay RAID set "sil_biaebhadcfcb" already active fdisk Output root@tripoli:~# fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b9b01 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 60802 488134657 5 Extended /dev/sda5 32 60802 488134656 8e Linux LVM Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6ead5c9a Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 fd Linux raid autodetect Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6e2af28 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 fd Linux raid autodetect

    Read the article

  • Setting up group disk quotas

    - by Ray
    I am hoping to get some advice in setting up disk quotas. So, I know about: Adding usrquota and grpquota on to /etc/fstab for the file systems that need to be managed. Using edquota to assign disk quotas to users. However, I need to do the last step for multiple users and edquota seems to be a bit troublesome. One solution that I have found is that I can do: sudo edquota -u foo -p bar. This will copy the disk quota of bar to user foo. I was wondering if this is the best solution? I tried setting up group disk quotas but they don't seem to be working. Are group quotas meant to help in the assignment of the same quota to multiple users? Or are they suppose to give a total limit to a set of users? For example, if users A, B, C are in group X then assigning a quota of 20 GB gives each user 20 GB or does it give 20 GB to the entire group X to divide up? I'm interested in doing the former, but not the latter. Right now, I've assigned group disk quotas and they aren't working. So, I guess it is due to my misunderstanding of group disk quotas... My problem is I want to easily give the same quota to multiple users; any suggestions on the best way to do this out of what I've tried above or anything else I may not have thought of? Thank you!

    Read the article

  • Can't remove GPT data from MBR

    - by user2373121
    I am having difficulty getting the Ubuntu installer (and gparted) to recognize the partitions on my MBR type disk. Other operating systems and disk tools read the disk structure and the files on it fine. I have used fixparts to write a new MBR but the issue persists. I assume the issue stems from the Protective MBR data still present on the disk but I am at a loss as to how to remove it while preserving my NTFS data partition. Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. c:\Users\mike\Desktop\fixpartsfixparts 3: FixParts 0.8.8 Loading MBR data from 3: Warning: 0xEE partition doesn't start on sector 1. This can cause problems in some OSes. MBR command (? for help): Running gdisk shows Microsoft Windows [Version 6.1.7601] Copyright (c) 2009 Microsoft Corporation. All rights reserved. c:\Users\mike\Desktop\fixparts>gdisk 3: GPT fdisk (gdisk) version 0.8.7 Partition table scan: MBR: MBR only BSD: not present APM: not present GPT: not present *************************************************************** Found invalid GPT and valid MBR; converting MBR to GPT format in memory. THIS OPERATION IS POTENTIALLY DESTRUCTIVE! Exit by typing 'q' if you don't want to convert your MBR partitions to GPT format! *************************************************************** ************************************************************************ Most versions of Windows cannot boot from a GPT disk, and most varieties prior to Vista cannot read GPT disks. Therefore, you should exit now unless you understand the implications of converting MBR to GPT or creating a new GPT disk layout! ************************************************************************ Are you SURE you want to continue? (Y/N): y Command (? for help): p Disk 3:: 2930277168 sectors, 1.4 TiB Logical sector size: 512 bytes Disk identifier (GUID): BFE92CE8-F93D-4141-82B8-816AD06FB36E Partition table holds up to 128 entries First usable sector is 34, last usable sector is 2930277134 Partitions will be aligned on 2048-sector boundaries Total free space is 163846893 sectors (78.1 GiB) Number Start (sector) End (sector) Size Code Name 1 163842048 2930272255 1.3 TiB 0700 Microsoft basic data Command (? for help): r Recovery/transformation command (? for help): o Disk size is 2930277168 sectors (1.4 TiB) MBR disk identifier: 0x00000000 MBR partitions: Number Boot Start Sector End Sector Status Code 1 1 2930277167 primary 0xEE Recovery/transformation command (? for help): q

    Read the article

  • My external hard drive letter is increasing each time i plugin it to my laptop, how to solve this pr

    - by Amr ElGarhy
    I have a strange problem, everytime i plugin my external hard drive, its letter increase, "g,h,i,j,k,l,m, then n, and now o" I went to computer manager and did what is described in this question: http://superuser.com/questions/76165/windows-changing-an-external-hard-drives-drive-letter To change the drive letter, but i found that the letters from h to n are all missed and not in the list. How to solve this problem? I am using windows 7 ultimate edition 32. 2GB Ram.

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0 [migrated]

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • Can WD3200AZRX SATA-3 hard drive work on SATA-2?

    - by Roberts
    I know this question is already been asked a lot of times. I am buying new hard drive today, but I am worrying that it wont work on my motherboard Gigabyte GA-945PL-S3. I want to buy this hard drive. It's pretty expensive and I don't want to get dissapointed. I can't find any documentation about jumper settings and that's why I am asking this question in this site, I hope somebody helps me. Have a nice day!

    Read the article

  • My new hard drive doesn't have rights on my old one?

    - by Allan
    Until recently I had a 1 TB hard disk with Windows 7 on it, I have bought myself a SSD, removed the old harddisc and installed Windows 7 on my new one. After that I put back the old hard disk, and formatted it, now I could use that as backup and to keep files on. Nice, right? Well I was updating .Net framework through Windows update, when it stalled. I noticed some space was used on one of the drives on my secondary 'previously primary' hard disk. Apparently it was the .Net framework, trying to save some temporary files on my secondary disc, because it was the one with the most space. It was like it didn't get access. I cancled the installation and rebooted the computer. Now wanting to remove the temporary folder on my secondary harddisk. It told me. "You don't have access by SYSTEM", I don't understand, my user is administrator, its the only user there is and at the same time I can remove and delete any other folder on that drive. I'm gonna go a little pseudo here. But it feels as if the computer treats the old harddisk as protected from tampering by the new SSD. Also, I feel I should mention, they are both listed as primary, ... primary 0 and primary 1. Both using SATA cable. My old hard drive was partioned into 3 drives. 2 of them said the current owner was 'Administrator/myPCname' and the third one said the current owner was 'SYSTEM' I changed them all into the only one that I could pick from the list, which is my user since the 'Administrators/myPCname' wasn't exactly wrong.. could it be that they were somehow still attached to the old OS?.. the fact is I named my computer the exact same thing as it was called before installing a new windows.. so I can't really tell if its an old ownership or not. Also.. I'm currently logged in as 'myname' and I'm administrator.. now trying to delete the previously mentioned files.. it says 'you need access from 'myname' – and it can't delete.. That seems really messed up, I mean I'm logged in as the name it wants me to use. Is there maybe someway I could reset all the users on my computer? Or create some default? I don't know – I just want it to take a form I have always known, from a standard Windows point of view.

    Read the article

  • Does having your page file on decrease the life expectancy of your hard drive?

    - by user695874
    If I have my page file turned on in Windows as opposed to having it turned off as shown below: Would having the page file turned on decrease the life expectancy on my Hard Drive? If so, how much would the life decrease say with regular use? (4 hours a day) I'm thinking it would decrease some just because there would be more writing to the hard drive, but I wasn't sure if it would be too negligible to even matter.

    Read the article

  • How can I access my external hard drive wirelessly from my laptop?

    - by leora
    My desktop crashed so I am migrated over to a laptop. I have wireless in my home so i am trying to be able to use to laptop in any room without any other connections (wireless printer, wireless mouse, etc) The one issue i have is that my desktop had 2 external hard drives (USB) connected to them and i am trying to figure out the best way to treat these as external drives without having to plug them into the laptop directly. My external hard drive is the Western Digital WDH1U5000N 500GB and my laptop is a Dell D620.

    Read the article

  • Mounting ddrescue image after recovery (in over my head)

    - by BorgDomination
    I'm having problems mounting the recovery image. I've tried to mount the image multiple ways. quark@DS9 ~ $ sudo mount -t ext4 /media/jump1/1recover/sdb1.img /mnt mount: wrong fs type, bad option, bad superblock on /dev/loop0, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so quark@DS9 ~ $ sudo mount -r -o loop /media/jump1/1recover/sdb1.img recover mount: you must specify the filesystem type quark@DS9 ~ $ sudo mount /media/jump1/1recover/sdb1.img mnt mount: you must specify the filesystem type It doesn't even give me detailed information on the file I just made, nautilus says it's 160gb. quark@DS9 ~ $ file /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img: data quark@DS9 ~ $ mmls /media/jump1/1recover/sdb1.img Cannot determine partition type I'm not sure what I'm doing wrong or if I started this process incorrectly from the beginning. I've outlined what I've done so far below. I'm clueless, I'd appreciate if someone had some input for me. What I have done from the beginning My laptop has two hard drives. One has the dual boot Win7 / Linux Mint system files. Secondary one contained my /home folder. The laptop was jarred and the /home disk was broken. I tried a LiveCD recovery, it failed. Wouldn't even load a Live session with the disk installed. So I turned to ddrescue. quark@DS9 ~ $ sudo fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009fc18 Device Boot Start End Blocks Id System /dev/sda1 * 2048 112642047 56320000 7 HPFS/NTFS/exFAT /dev/sda2 138033152 312580095 87273472 83 Linux /dev/sda3 112644094 138033151 12694529 5 Extended /dev/sda5 112644096 132173823 9764864 83 Linux /dev/sda6 132175872 138033151 2928640 82 Linux swap / Solaris Partition table entries are not in disk order Disk /dev/sdb: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0002a8ea Device Boot Start End Blocks Id System /dev/sdb1 * 63 312576704 156288321 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xed6d054b Device Boot Start End Blocks Id System /dev/sdc1 63 1953520064 976760001 7 HPFS/NTFS/exFAT sda - 160g internal, holds all system files and all computer functions. sdb - 160g internal, BROKEN, contains about 140g of data I'd like to recover. sdc - 1T external, contains recovery image. Only place that has space to do all this. From this site, https://apps.education.ucsb.edu/wiki/Ddrescue I used this script to create an image of the broken hard drive. I changed the destination to the external USB drive. #!/bin/sh prt=sdb1 src=/dev/$prt dst=/media/jump1/1recover/$prt.img log=$dst.log sudo time ddrescue --no-split $src $dst $log sudo time ddrescue --direct --max-retries=3 $src $dst $log sudo time ddrescue --direct --retrim --max-retries=3 $src $dst $log Everything looked like it came off without a hitch: quark@DS9 ~ $ sudo bash recover1 Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 0 B, errsize: 0 B, errors: 0 Current status rescued: 160039 MB, errsize: 4096 B, current rate: 35588 B/s ipos: 3584 B, errors: 1, average rate: 22859 kB/s opos: 3584 B, time from last successful read: 0 s Finished 12.78user 1060.42system 1:56:41elapsed 15%CPU (0avgtext+0avgdata 4944maxresident)k 312580958inputs+0outputs (1major+601minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 4096 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 13 B/s opos: 1536 B, time from last successful read: 1.3 m Finished 0.00user 0.00system 3:43.95elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 238inputs+0outputs (3major+374minor)pagefaults 0swaps Press Ctrl-C to interrupt Initial status (read from logfile) rescued: 160039 MB, errsize: 1024 B, errors: 1 Current status rescued: 160039 MB, errsize: 1024 B, current rate: 0 B/s ipos: 1536 B, errors: 1, average rate: 0 B/s opos: 1536 B, time from last successful read: 3.7 m Finished 0.00user 0.00system 3:43.56elapsed 0%CPU (0avgtext+0avgdata 4944maxresident)k 8inputs+0outputs (0major+376minor)pagefaults 0swaps It looks like, from where I'm standing it worked perfectly. Here's the log: # Rescue Logfile. Created by GNU ddrescue version 1.14 # Command line: ddrescue --direct --retrim --max-retries=3 /dev/sdb1 /media/jump1/1recover/sdb1.img /media/jump1/1recover/sdb1.img.log # current_pos current_status 0x00000600 + # pos size status 0x00000000 0x00000400 + 0x00000400 0x00000400 - 0x00000800 0x254314FC00 + I'm not sure how to proceed. Does this mean all of my data is lost???????? Appreciate ANY input!

    Read the article

  • Recover Deleted Files on an NTFS Hard Drive from a Ubuntu Live CD

    - by Trevor Bekolay
    Accidentally deleting a file is a terrible feeling. Not being able to boot into Windows and undelete that file makes that even worse. Fortunately, you can recover deleted files on NTFS hard drives from an Ubuntu Live CD. To show this process, we created four files on the desktop of a Windows XP machine, and then deleted them. We then booted up the same machine with the bootable Ubuntu 9.10 USB Flash Drive that we created last week. Once Ubuntu 9.10 boots up, open a terminal by clicking Applications in the top left of the screen, and then selecting Accessories > Terminal. To undelete our files, we first need to identify the hard drive that we want to undelete from. In the terminal window, type in: sudo fdisk –l and press enter. What you’re looking for is a line that ends with HPSF/NTFS (under the heading System). In our case, the device is “/dev/sda1”. This may be slightly different for you, but it will still begin with /dev/. Note this device name. If you have more than one hard drive partition formatted as NTFS, then you may be able to identify the correct partition by the size. If you look at the second line of text in the screenshot above, it reads “Disk /dev/sda: 136.4 GB, …” This means that the hard drive that Ubuntu has named /dev/sda is 136.4 GB large. If your hard drives are of different size, then this information can help you track down the right device name to use. Alternatively, you can just try them all, though this can be time consuming for large hard drives. Now that you know the name Ubuntu has assigned to your hard drive, we’ll scan it to see what files we can uncover. In the terminal window, type: sudo ntfsundelete <HD name> and hit enter. In our case, the command is: sudo ntfsundelete /dev/sda1 The names of files that can recovered show up in the far right column. The percentage in the third column tells us how much of that file can be recovered. Three of the four files that we originally deleted are showing up in this list, even though we shut down the computer right after deleting the four files – so even in ideal cases, your files may not be recoverable. Nevertheless, we have three files that we can recover – two JPGs and an MPG. Note: ntfsundelete is immediately available in the Ubuntu 9.10 Live CD. If you are in a different version of Ubuntu, or for some other reason get an error when trying to use ntfsundelete, you can install it by entering “sudo apt-get install ntfsprogs” in a terminal window. To quickly recover the two JPGs, we will use the * wildcard to recover all of the files that end with .jpg. In the terminal window, enter sudo ntfsundelete <HD name> –u –m *.jpg which is, in our case, sudo ntfsundelete /dev/sda1 –u –m *.jpg The two files are recovered from the NTFS hard drive and saved in the current working directory of the terminal. By default, this is the home directory of the current user, though we are working in the Desktop folder. Note that the ntfsundelete program does not make any changes to the original NTFS hard drive. If you want to take those files and put them back in the NTFS hard drive, you will have to move them there after they are undeleted with ntfsundelete. Of course, you can also put them on your flash drive or open Firefox and email them to yourself – the sky’s the limit! We have one more file to undelete – our MPG. Note the first column on the far left. It contains a number, its Inode. Think of this as the file’s unique identifier. Note this number. To undelete a file by its Inode, enter the following in the terminal: sudo ntfsundelete <HD name> –u –i <Inode> In our case, this is: sudo ntfsundelete /dev/sda1 –u –i 14159 This recovers the file, along with an identifier that we don’t really care about. All three of our recoverable files are now recovered. However, Ubuntu lets us know visually that we can’t use these files yet. That’s because the ntfsundelete program saves the files as the “root” user, not the “ubuntu” user. We can verify this by typing the following in our terminal window: ls –l We want these three files to be owned by ubuntu, not root. To do this, enter the following in the terminal window: sudo chown ubuntu <Files> If the current folder has other files in it, you may not want to change their owner to ubuntu. However, in our case, we only have these three files in this folder, so we will use the * wildcard to change the owner of all three files. sudo chown ubuntu * The files now look normal, and we can do whatever we want with them. Hopefully you won’t need to use this tip, but if you do, ntfsundelete is a nice command-line utility. It doesn’t have a fancy GUI like many of the similar Windows programs, but it is a powerful tool that can recover your files quickly. See ntfsundelete’s manual page for more detailed usage information Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDUse Ubuntu Live CD to Backup Files from Your Dead Windows ComputerCreate a Bootable Ubuntu 9.10 USB Flash DriveCreate a Bootable Ubuntu USB Flash Drive the Easy WayGuide to Using Check Disk in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Windows 7 Easter Theme YoWindoW, a real time weather screensaver Optimize your computer the Microsoft way Stormpulse provides slick, real time weather data Geek Parents – Did you try Parental Controls in Windows 7? Change DNS servers on the fly with DNS Jumper

    Read the article

  • Monitor file disk activity programmatically (Windows)

    - by iulianchira
    In Windows 2008R2, in Resource Monitor in the Disk Acitivity section I can see the number of bytes read from/written into files. How can I do this in a programatic manner, prefferably using C# (or Win32 API)? I have looked into WMI and various performance counters, however I cannot figure out if there is something which suits my needs.

    Read the article

< Previous Page | 28 29 30 31 32 33 34 35 36 37 38 39  | Next Page >