Search Results

Search found 12251 results on 491 pages for 'intel wireless card'.

Page 33/491 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

• Intel GMA 4500MHD flickering in opengl

  - by Aaron

  I have an application that uses OpenGL for its display. When this application is run on a laptop with an Intel GMA 4500MHD on Windows XP the OpenGL content appears to flicker/shudder between 2 frames. I have experienced the exact same problem when running this application on nVidia Quadro FX hardware, however with nVidia the problem can be corrected by disabling the "Unified Back Buffer" (UBB) feature in the driver. Does anybody know how I can disable the corresponding feature in the Intel driver?

  Read the article

• Intel GMA 4500MHD flickering in opengl

  - by Aaron

  I have an application that uses OpenGL for its display. When this application is run on a laptop with an Intel GMA 4500MHD on Windows XP the OpenGL content appears to flicker/shudder between 2 frames. I have experienced the exact same problem when running this application on nVidia Quadro FX hardware, however with nVidia the problem can be corrected by disabling the "Unified Back Buffer" (UBB) feature in the driver. Does anybody know how I can disable the corresponding feature in the Intel driver?

  Read the article

• Shuttle SG31G2V2 Intel Socket T(LGA775) Intel G31 Motherboard Model?

  - by unknown (google)

  Hi Everyone. Can anyone tell me what is the intel motherboard model for this shuttle barebone kit. I know the chipset is g31 but for drivers from intel what is the exact model number for this system. http://www.newegg.com/Product/Product.aspx?Item=N82E16856101037

  Read the article

• wifi problems with lenovo g580 on kubuntu-13.04-desktop-amd64

  - by user203963

  i have a wifi connection problem in lenovo g580 on kubuntu-13.04-desktop-amd64. ethernet cable is working properly but wifi does'nt connect below are some hardware information sudo lshw -class network gives *-network description: Ethernet interface product: AR8162 Fast Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:89:84:3d:e9:10 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm pciexpress msi msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=alx driverversion=1.2.3 duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:16 memory:90500000-9053ffff ioport:2000(size=128) *-network description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=bcma-pci-bridge latency=0 resources: irq:17 memory:90400000-90403fff *-network description: Wireless interface physical id: 3 logical name: wlan0 serial: 68:94:23:fa:2c:d9 capabilities: ethernet physical wireless configuration: broadcast=yes driver=brcmsmac driverversion=3.8.0-19-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bgn lsubs gives Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0489:e032 Foxconn / Hon Hai Bus 002 Device 003: ID 04f2:b2e2 Chicony Electronics Co., Ltd lspci gives 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 (rev c4) 00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation HM76 Express Chipset LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04) 01:00.0 Ethernet controller: Qualcomm Atheros AR8162 Fast Ethernet (rev 10) 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Does anyone knows the solution? rfkill list all gives 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: yes Hard blocked: no 2: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 3: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Broadcom WiFi drivers conflict

  - by james

  $ sudo dpkg -i wireless-bcm43142-dkms-6.20.55.19_amd64.deb dpkg: acerca de wireless-bcm43142-dkms-6.20.55.19_amd64.deb que contiene wireless-bcm43142-oneiric-dkms: wireless-bcm43142-oneiric-dkms entra en conflicto con bcmwl-kernel-source bcmwl-kernel-source (versión 6.20.155.1+bdcom-0ubuntu0.0.2) está presente y instalado. dpkg: error al procesar wireless-bcm43142-dkms-6.20.55.19_amd64.deb (--install): paquetes en conflicto - no se instalará wireless-bcm43142-oneiric-dkms Se encontraron errores al procesar: wireless-bcm43142-dkms-6.20.55.19_amd64.deb Help me find a solution to install this .deb package.

  Read the article

• micro-SD card initialization using SPI interface

  - by Ron

  I'm using a micro-SD card in an embedded design. The card is connected to a microcontroller using the SPI interface. It worked fine for all cards I've used before, but now my new card will not initialize. The card is a Transcend 2GB micro-SD card (TS2GUSD). After sending the initial clock train to switch to SPI mode I do the following: 1) CMD0 (Argument 0, CRC 0x95) - Response 0x01 - OK 2) CMD8 (Argument 0x000001AA, CRC 0x87) - Response 0x01 0x000001AA - Means it's SDC V2+ card, the Voltage range 2.7V~3.6V is supported - OK Then I should send the ACMD41 command, but when sending the CMD55 (argument 0, CRC 0) that must precede CMD41, I get response 0x05 - Illegal Command. I've also tried to send CMD1 (for MMC cards), but it gives a similar Illegal Command response. The code works fine with my Sandisk 2GB micro-SD card. Does anyone have any idea? Thanks, -Ron-

  Read the article

• Creating a standard card game (iPhone SDK)

  - by Chris

  I am trying to create a card game with a standard deck of cards. I need to be able to create a new card on screen every time someone draws a card from the deck and then be able to continuously move it throughout gameplay. I have image files for every card available in the game. I have tried creating a card object which held a UIImageView for the card along with some other basic data but I had trouble referring back to that card to move it again after the first touch. Was this the right way to do this?

  Read the article

• Sony Vaio PCG-71315L "Wireless is disabled by hardware switch" Help!

  - by Luke Rossi

  I'm a new user to Ubuntu and Linux as a whole, I've had it for a few months and just as I'm starting to get a feel for things my wireless decided to quit on me. This puzzled me so i checked all the switches on the Vaio; my wireless switch was on (my bluetooth was also working), and in my windows partition the problem is non-existent. Help please? Anyways after executing the "rfkill list" command this was the outcome: 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no 2: sony-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 3: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 4: hci0: Bluetooth Soft blocked: no Hard blocked: no As stated in the title my laptop is a Sony Vaio PCG-71315L

  Read the article

• How do I get wireless working on a Dell Inspiron 510m?

  - by user17449

  Why WiFi don't work in my Dell Inspiron 510m with Ubuntu 10.04? Is that usefull? inspiron@Inspiron:~$ rfkill list all inspiron@Inspiron:~$ sudo lshw -C network [sudo] password for inspiron: *-network:0 DISABLED description: Wireless interface product: PRO/Wireless LAN 2100 3B Mini PCI Adapter vendor: Intel Corporation physical id: 3 bus info: pci@0000:01:03.0 logical name: eth1 version: 04 serial: 00:0c:f1:5b:5d:40 width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ipw2100 driverversion=git-1.2.2 firmware=712.0.3:3:00000001 latency=32 link=no maxlatency=34 mingnt=2 multicast=yes wireless=unassociated resources: irq:5 memory:fcffe000-fcffefff *-network:1 description: Ethernet interface product: 82801DB PRO/100 VE (MOB) Ethernet Controller vendor: Intel Corporation physical id: 8 bus info: pci@0000:01:08.0 logical name: eth0 version: 81 serial: 00:11:43:41:d8:b8 size: 10MB/s capacity: 100MB/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e100 driverversion=3.5.24-k2-NAPI duplex=half firmware=N/A ip=192.168.0.2 latency=32 link=no maxlatency=56 mingnt=8 multicast=yes port=MII speed=10MB/s resources: irq:11 memory:fcffd000-fcffdfff ioport:ecc0(size=64) inspiron@Inspiron:~$ iwconfig wlan0 wlan0 No such device inspiron@Inspiron:~$ ifconfig -a eth0 Link encap:Ethernet Endereço de HW 00:11:43:41:d8:b8 inet end.: 192.168.0.2 Bcast:192.168.0.255 Masc:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet Endereço de HW 00:0c:f1:5b:5d:40 BROADCAST MULTICAST MTU:1500 Métrica:1 pacotes RX:0 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:0 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) IRQ:5 Endereço de E/S:0xe000 Memória:fcffe000-fcffefff lo Link encap:Loopback Local inet end.: 127.0.0.1 Masc:255.0.0.0 endereço inet6: ::1/128 Escopo:Máquina UP LOOPBACK RUNNING MTU:16436 Métrica:1 pacotes RX:628 erros:0 descartados:0 excesso:0 quadro:0 Pacotes TX:628 erros:0 descartados:0 excesso:0 portadora:0 colisões:0 txqueuelen:0 RX bytes:50104 (50.1 KB) TX bytes:50104 (50.1 KB) inspiron@Inspiron:~$ nm-tool NetworkManager Tool State: connected - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: ipw2100 State: unavailable Default: no HW Address: 00:0C:F1:5B:5D:40 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: e100 State: unmanaged Default: no HW Address: 00:11:43:41:D8:B8 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: off inspiron@Inspiron:~$

  Read the article

• How do I select Wireless radio portions in Ubuntu?

  - by Ryan McClure

  Bear with me, to be honest I have no idea what Wireless radio portions are.... At my school, I was told my the user support that the wireless network in my dorm uses 801.11 A/B/G/N. For some reason, the wireless in my room doesn't work. However, other buildings use only A/B/G, they say. In any other building, my wireless works fine. How do I tell my system to use the G portion only? (As requested by user support in the email I received). Here are the various logs/output requested: dmesg lshw -c network lsmod

  Read the article

• How can I get wireless working on an HP-Mini 110-3150?

  - by jfmessier

  I just got an HP Mini 110-3150, and booting from an external hard disk with Ubuntu 10.10 works all fine, except that there is no wireless detected. I noticed that the Wireless indicator is red under Ubuntu, but is enabled under whatever Windows 7 I got on it. So, I understand that it may not get detected at all by Ubuntu at startup time, and there is no manual switch that I can simply slide to turn on/off. How can I get the Wireless device turned ON by default at startup time, and is there any special driver I need to install (proprietary or not) to get it working ? Merci :-) Update: When actually installing on the computer, as a new install, the NIC is not detected at first, but upon restarting, I get a notification of a closed driver available for the wireless. Once installed, updated and restarted, it works fine.

  Read the article

• How do I get to work my Atheros AR9485 Wireless card in Ubuntu 14.04 LTS?

  - by Ivan Kreimer

  I've recently installed Ubuntu 14.04 LTS in my ASUS D550CA, and so far things have gone great. The only problem I've got is the Wi-Fi. It doesn't work. I've got an Qualcomm Atheros AR9485. I've tried installing the drivers, but the sytem says it doesn't find any. So I started looking around this forum for solutions. I've read every single post from this forum about my Wi-Fi network adapter, and I've found nothing that solves my problem. Let me give you some info about my configuration. Disclaimer: my configuration is in spanish, so if you don't understand something you can either use Google translate, or use your imagination. :D When I run $ sudo lshw -C network this is what I get: *-network DEACTIVATED descripción: Interfaz inalámbrica producto: AR9485 Wireless Network Adapter fabricante: Qualcomm Atheros id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: wlan0 versión: 01 serie: 28:e3:47:5c:5d:3f anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.13.0-34-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:f7d00000-f7d7ffff memoria:f7d80000-f7d8ffff *-network descripción: Ethernet interface producto: RTL8101E/RTL8102E PCI Express Fast Ethernet controller fabricante: Realtek Semiconductor Co., Ltd. id físico: 0.2 información del bus: pci@0000:03:00.2 nombre lógico: eth0 versión: 06 serie: e0:3f:49:ce:57:49 tamaño: 100Mbit/s capacidad: 100Mbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8402-1_0.0.1 10/26/11 ip=181.165.245.39 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s recursos: irq:41 ioport:e000(size=256) memoria:f0004000-f0004fff memoria:f0000000-f0003fff At the beginning, you'll see that it says "*-network DEACTIVATED" (or at least that's what I translated), is that something bad? Then, when I run ipconfig this is what I get: eth0 Link encap:Ethernet direcciónHW e0:3f:49:ce:57:49 Direc. inet:181.165.245.39 Difus.:181.165.245.255 Másc:255.255.255.0 Dirección inet6: fe80::e23f:49ff:fece:5749/64 Alcance:Enlace ACTIVO DIFUSIÓN FUNCIONANDO MULTICAST MTU:1500 Métrica:1 Paquetes RX:221199 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:62025 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:1000 Bytes RX:124409589 (124.4 MB) TX bytes:7471899 (7.4 MB) lo Link encap:Bucle local Direc. inet:127.0.0.1 Másc:255.0.0.0 Dirección inet6: ::1/128 Alcance:Anfitrión ACTIVO BUCLE FUNCIONANDO MTU:65536 Métrica:1 Paquetes RX:2977 errores:0 perdidos:0 overruns:0 frame:0 Paquetes TX:2977 errores:0 perdidos:0 overruns:0 carrier:0 colisiones:0 long.colaTX:0 Bytes RX:397158 (397.1 KB) TX bytes:397158 (397.1 KB) When I put iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Finally, when I put sudo rfkill list all, I got: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no I hope anyone can help me solve this, I've searched a lot and found no solution. Thanks a lot.

  Read the article

• How can I make NetworkManager ignore my wireless card?

  - by ændrük

  I do not want NetworkManager to list or manipulate my wireless card. Can I hide its interface from NetworkManager somehow? I have tried adding this in /etc/network/interfaces, iface wlan0 inet static address 192.168.1.101 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid Synaptotagmin pre-up wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf post-down killall -q wpa_supplicant and this in /etc/NetworkManager/nm-system-settings.conf, [keyfile] unmanaged-devices=/org/freedesktop/Hal/devices/net_00_19_e0_57_86_af but NetworkManager Applet still lists and allows me to connect to wireless networks.

  Read the article

• How do I disable the "enable/disable wireless" shortcut key on my laptop?

  - by Matthew

  On my Dell Studio XPS 16, I sometimes accidentally hit this key. Wireless becomes disabled, and hitting it again does not re-enable wireless. I have to hit it an odd number of times, then restart my computer to re-enable wireless. I can't imagine a situation in which I would want to disable wireless from my keyboard. Is it possible just disable the key all-together, so I can avoid this problem? On a related note, what package do I file the bug against? I'm happy just disabling the key, but that's really just a workaround.

  Read the article

• How do I get my Lenovo T61 to connect to a wireless network?

  - by Ross Fleming

  I have a Lenovo Thinkpad T61 and the wireless works just fine so I installed Ubuntu straight away only to find that the wireless will not connect, it will see the networks but just not connect. Has anyone managed to solve this all the forums seem to relate to Ubuntu 9.04 and before. Edit:Sorry about that, I didn't realise that there were 2 models mine is the Intel Corporation PRO/Wireless 4965 AG or AGN [Kedron] Network Connection. Any help is much appreciated.

  Read the article

• How can I make NetworkManager ignore my wireless card?

  - by ændrük

  I do not want NetworkManager to list or manipulate my wireless card. Can I hide its interface from NetworkManager somehow? I have tried adding this in /etc/network/interfaces, iface wlan0 inet static address 192.168.1.101 netmask 255.255.255.0 gateway 192.168.1.1 wireless-essid Synaptotagmin pre-up wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf post-down killall -q wpa_supplicant and this in /etc/NetworkManager/nm-system-settings.conf, [main] plugins=ifupdown,keyfile [ifupdown] managed=false [keyfile] unmanaged-devices=/org/freedesktop/Hal/devices/net_00_19_e0_57_86_af but NetworkManager Applet still lists and allows me to connect to wireless networks.

  Read the article

• How well does an INCA IM-201W Wireless work?

  - by Eray

  I'm using Ubuntu 11.04 . I'll buy a wireless modem, Inca IM-201W . But i'm looking supported OS of modem : Windows XP , Vista, 7 . There isn't Ubuntu in list.SO what's the meaning of this ? Shouldn't I buy this modem ? I will use wireless connection. (PS. Sometimes, while i'm trying to connect a Wireless network on any cafe, i'm having problem. My laptop isn't connecting to wireless networks sometimes . )

  Read the article

• How can I configure the embedded wireless card in a Toshiba Satellite Pro 4600 to work under Lubuntu 10.10?

  - by MoLE

  I'm struggling to get the embedded wireless card in this laptop to work. In 7.10 (gutsy) it worked fine. Now I'm trying to get 10.10 (maverick) working on it, and am using the Lubuntu flavour due to the low resources of this laptop. The hardware: Appears to be an embedded pcmcia card. pccardctl ident gives: Socket 0: product info: "TOSHIBA", "Wireless LAN Card", "Version 01.01", "" manfid: 0x0156, 0x0002 function: 6 (network) The default kernel recognises the card and loads the orinoco_cs driver. orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0001:0006:000e orinoco_cs 0.0: Firmware determined as Lucent/Agere 6.14 Then for some reason, the driver isn't happy with this and gives: orinoco_cs 0.0: Hardware identity 0005:0002:0001:0002 orinoco_cs 0.0: Station identity 001f:0002:0009:0030 orinoco_cs 0.0: Firmware determined as Lucent/Agere 9.48 All seems ok until I try to associate with my access point using Network Manager. eth1: Lucent/Agere firmware doesn't support manual roaming repeated about 10 times then NM gives up. According to the linuxwireless.org wiki page on this driver, this is a known issue, and I quote: Known issues Roaming and WPA_supplicant Lucent/Agere firmware doesn't support manual roaming On the Agere cards, roaming is controlled by the firmware instead of userspace. You will get the above message if userspace attempts to associate with a specific AP rather than by SSID. If you are using wpa_supplicant use ap_scan=2 mode. NetworkManager uses wpa_supplicant, so the above also applies. At this point my google-fu has failed me, and I can't find how to configure network manager to use the mystical "ap_scan=2" mode via wpa_supplicant. I have tried the following suggested solutions (from launchpad or the forums) deleting the agere* files from /lib/firmware using wicd instead of network manager combining both blacklisting the orinoco_cs driver in an attempt to force use of the hostap_cs driver instead (in case it is a prism2 card). Obviously none of them have worked for me. Any hints on how to perform the suggested workaround above? Edit: I have also confirmed working on 8.10 (intrepid) live CD.

  Read the article

• Can realtek 8192cu usb wireless card be used in ubuntu 12.04 with kernel 3.2.0?

  - by waterloo2005

  I do like the post RTL8188CUS Wireless USB Dongle doesn't work unless I disable wireless security . But when I plug my 8192cu usb wireless card, my computer screen is off. At that time I even can not use Alt SysRq k or Alt SysRq + reisub. I compile the latest driver of 8192cu on ubuntu 12.04 with kernel 3.2.0-34. In RealTek site, I download 8192cu drive which is for Linux Kernel 2.6.18~2.6.38 and Kernel 3.0.8. But now in Ubuntu12.04 my kernel is 3.2.0-34. Every time I plug the usb 8192cu wireless card my system halts. Now I try to blacklist both the system's rtl8192cu driver and the new 8192cu driver I compile, but the system still halts when I plug the usb driver. What about you ? Thanks!

  Read the article

• Why doesn't wireless work on Wubi 12.04 with a Broadcom BCM4312 card?

  - by Kristin

  I have recently set up ubuntu 12.04 on my laptop using the Wubi installer. I am having a very difficult time setting up a wireless internet connection. I am currently set up with an ethernet connection which I have used to download all new updates and to activate the Broadcom STA wireless driver. I have tried several things in the terminal based on other people's posts: ~$ rfkill list 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes ~$ rfkill unblock all It doesn't change anything. I also tried rebooting and connecting to the internet on my Windows Vista OS, and it worked, so I know that the connection should not be hard blocked. I have also tried installing b43 firmware (lp/phy version) that is supposed to work with my chip (BCM4312). It seems to have no effect. Then I tried: ~$ iwconfig lo no wireless extensions. eth1 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. This is my first time trying to work with ubuntu, so I would appreciate any help. Thanks. Also sorry this is poorly formatted. I'm having troubles with that too.

  Read the article

• Wireless doesn't work for me in Lubuntu but does in Puppy?

  - by user54871

  I am new to GNU Linux. I have been having trouble getting wireless working on my installed system of Lubuntu 11.10. It sees my WPA network but cannot connect even when I remove the password. Looking around for a different distro that might replace it, I was amazed to find that Puppy was able to connect to my wireless network without trouble, running off a USB stick. So this makes me think that my Lubuntu wireless problem might be fixable so I don't have to have the major hassle of backing up all my documents etc before installing a different distro to the laptop. Can anyone suggest some steps that might help me to fix wireless on Lubuntu, perhaps using the fact it works with Puppy? Thanks. Rob

  Read the article

• How to set up dual wired and wireless connections?

  - by Col

  My laptop has both wireless and a wired connection capabilities. Can I connect to a router A using wireless and a separate router B using wired ethernet at the same time without having to switch back and forth? Thanks for replying so quickly. I wish to connect to two separate networks. The wireless connection is to router A which is connected to broadband internet. The wired connection is to router B which I wish to share files and a printer on 1 or 2 other desktops also using wired connections on B and maybe using synergy to have only one keyboard and mouse for 2 desktops. The wireless laptop is the only one required to have internet access.

  Read the article

• Wireless (Broadcom) just stopped working after putting machine to sleep!

  - by tommed

  Had the wireless working on my Dell Studio 15 for months now (Ubuntu 10.04 64bit, now 10.10 64bit). But I shut the lid this morning, which put the machine to sleep; when I openend it again the wireless would no longer connect to anything :'( I rebooted the machine, but that didn't help. I then did ifconfig eth1 {down,up}, but that didn't help, then I did iwconfig eth1 power {down,on}, but that didn't work. So I uninstalled the wireless driver (Broadcom STA) from additional drivers (reboot in the middle), but it still won't work anymore!! This is the trace from daemon.log, looks like it is a driver issue? Nov 28 12:26:39 ulap NetworkManager[1218]: (eth1): supplicant connection state: disconnected - scanning Nov 28 12:26:39 ulap NetworkManager[1218]: (eth1): supplicant connection state: scanning - disconnected Nov 28 12:26:45 ulap NetworkManager[1218]: (eth1): supplicant connection state: disconnected - scanning Nov 28 12:26:50 ulap wpa_supplicant[1295]: Trying to associate with MY_MAC_CODE (SSID='MY_WIRESS_SSID' freq=2417 MHz) Nov 28 12:26:50 ulap wpa_supplicant[1295]: Association request to the driver failed Nov 28 12:26:50 ulap NetworkManager[1218]: (eth1): supplicant connection state: scanning - associating Nov 28 12:26:51 ulap wpa_supplicant[1295]: Associated with MY_MAC_CODE Nov 28 12:26:51 ulap NetworkManager[1218]: (eth1): supplicant connection state: associating - associated Nov 28 12:27:01 ulap wpa_supplicant[1295]: Authentication with MY_MAC_CODE timed out. Nov 28 12:27:01 ulap NetworkManager[1218]: (eth1): supplicant connection state: associated - disconnected Anyone seen this, or know how I can get around this issue? It had been working fine up until now?! Even ran update-manager, but there wasn't any changes to the wireless drivers (or any related networking areas). Running the most up-to-date version of 10.10 x64. My android phone and other devices are still working on the wireless.

  Read the article

• How do I enable wireless on HP Pavilion dm1?

  - by Dikla

  My wireless network is physically enabled and the "enable wireless" appears properly on the top menu, however checking it doesn't seem to have any affect. Anyone came across this problem? I have a new HP Pavilion dm1-4000, installed Ubuntu 11.10 yesterday. The wireless worked fine yesterday, today I've got nothing. It also seems to have problems with the wired connection, however I have no idea if it's related.

  Read the article

• ubuntu 10.04: wlan0 No such device

  - by AodhanOL

  I am using a Dell xps l702x and I am using ubuntu 10.04 because I need to use f77 (don't ask) and I wasn't able to get it working on later versions of ubuntu. I cannot use the wifi at all. I have tried to fix it and have had limited success (changed the output from rfkill list all from Hard blocked: yes, to hard blocked: no). Here is the output from rfkill list all aodhan@aodhan-laptop:~$ rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: dell-wifi: Wireless LAN Soft blocked: no Hard blocked: no 2: dell-bluetooth: Bluetooth Soft blocked: no Hard blocked: no Here is the output from iwconfig: aodhan@aodhan-laptop:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions. pan0 no wireless extensions. And here is the output from ifconfig -a: aodhan@aodhan-laptop:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr 5c:f9:dd:3d:f2:f7 inet addr:192.168.1.17 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::5ef9:ddff:fe3d:f2f7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3417 errors:0 dropped:0 overruns:0 frame:0 TX packets:2894 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3317567 (3.3 MB) TX bytes:505049 (505.0 KB) Interrupt:30 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:12 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:720 (720.0 B) TX bytes:720 (720.0 B) pan0 Link encap:Ethernet HWaddr 7e:7e:e8:39:70:af BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) And finally, the output from lspci: 00:00.0 Host bridge: Intel Corporation Device 0104 (rev 09) 00:01.0 PCI bridge: Intel Corporation Sandy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Device 0116 (rev 09) 00:16.0 Communication controller: Intel Corporation Cougar Point HECI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation Cougar Point High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 4 (rev b5) 00:1c.4 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 5 (rev b5) 00:1c.5 PCI bridge: Intel Corporation Cougar Point PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation Cougar Point USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation Device 1c4b (rev 05) 00:1f.2 SATA controller: Intel Corporation Cougar Point 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation Cougar Point SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation Device 1246 (rev a1) 03:00.0 Network controller: Intel Corporation Device 008a (rev 34) 04:00.0 USB Controller: NEC Corporation Device 0194 (rev 04) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Please help me! Thank you in advance. Edit: Further info - this is a dual install with a windows 7 system as the other option. However, I can't access that until tomorrow (I won't have access to the windows 7 disc until then, and grub isn't letting me load it). Therefore, I can't be sure whether it still works on that or not. It used to, though.

  Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >