Search Results

Search found 10859 results on 435 pages for 'raid controller'.

Page 33/435 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

  • Debian: Disable software Raid?

    - by DebFo
    Hey, I own a server with 2 hdds and I used a debian raid installation template. Know I want to reinstall my server and don't want raid anymore to have more space. My provider wants money to change the template to a non-raid debian one. Is there a way to disable software raid on linux after a fresh installation? Thanks

    Read the article

  • Should I buy matching hard drives for a NAS RAID 1 array?

    - by Jamie Ide
    I'm planning to buy a NAS (network attached storage) box and I've picked the Synology DS209. I want to set up a RAID 1 array and I'm wondering if I should buy a matching pair of hard drives or if it would be better to buy from different manufacturers. I'm concerned that a matching pair would be more likely to fail at the same time.

    Read the article

  • Dell PowerEdge R720 - Corrupted RAID

    - by BT643
    Apologies in advance for the lengthy question. We have a Dell PowerEdge R720 server with: 2 x 136GB SAS drives in RAID 1 for the OS (Ubuntu Server 12.04) 6 x 3TB SATA drives in RAID 5 for data A few days ago we were getting errors when trying to access files on the large RAID 5 partition. We rebooted the server and got a message about the raid controller has found a foriegn config. We've had this before, and just needed to use Dell's RAID configuration utility to import foreign config on the RAID. Last time this worked, but this time, it started doing a disk check then we got this: FSCK has returned the following: "/dev/sdb1 inode 364738 has a bad extended attribute block 7 /dev/sdb1 unexpected inconsistency run fsck manually (i.e without -a or -p options) MOUNTALL fsck /ourdatapartition [1019] terminated with status 4 MOUNTALL filesystem has errors /ourdatapartition errors where found while checking the disk drive for /ourdatapartition Press F to fix errors, I to Ignore or M for Manual Recovery" We pressed F to try and fix the errors, but it eventually errored with: Inode 275841084, i_blocks is 167080, should be 0. Fix? yes Inode 275841141 has an invalid extend node (blk 2206761006, lblk 0) Clear? yes Inode 275841141, i_blocks is 227872, should be 0. Fix? yes Inode 275842303 has an invalid extend node (blk 2206760975, lblk 0) Clear? yes .... Error storing directory block information (inode=275906766, block=0, num=2699516178): Memory allocation failed /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** e2fsck: aborted /dev/sdb1: ***** FILE SYSTEM WAS MODIFIED ***** mountall: fsck /ourdatapartition [1286] terminated with status 9 mountall: Unrecoverable fsck error: /ourdatapartition We noticed one of the drive lights was not lit at all, and thought this may have failed and be the problem. We replaced the drive with a spare, and tried "F" to repair it again, but we keep just getting the same error as above. In the RAID configuration utility, all drives show as "online" and "optimal". We do have this data on another replicated server, so we're not worried about "recovering" anything, we just want to get the system back online asap. The server has 64 or 32GB memory, can't remember off the top of my head, but either way, with a 14TB RAID, I think it may still not be enough. Thanks EDIT - I checked the memory usage while fsck was running as suggested and after 2 or 3 minutes, it looked like this, using up nearly all of our servers memory: When it failed after 5 minutes or so with the error in my post, the memory immediately freed up again:

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0 [migrated]

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • How to know which disk has failed on a Mirrored Raid? marked as DR0

    - by Saariko
    Our 2ndry DC, which is on a W2K8R2 Mirrored software raid has lost it's sync, and disk management displays the failed redundancy error How do I know which of the disks has failed? (beside to try and replace one - and see if it loads and syncs) On the device manager, under disks I see both disks, one of them has an icon of: Disable, while the other doesn't Event log displays an event id 7 - bad block on Hard disk DR0 The thing is that looking in device manager, both disks are located in '0' location, which is bizzare

    Read the article

  • Is data=journal on a separate device on Ext4 as good as using a RAID controller with battery backed cache for file system consistency?

    - by Jeff Strunk
    It seems to me that data=journal prevents file system inconsistency in the case of power failure. Using it with a dedicated journal device mitigates the performance penalty of writing the data twice. A power outage would still lose the data that is currently being written to the journal, but the file system on disk would always be consistent. If that amount of loss is acceptable, is a RAID controller with battery backed cache really worthwhile?

    Read the article

  • How to have 3 operating systems on a mirror RAID 1.

    - by Chris_45
    How do one proceed if I want to have 3 Operating Systems: Windows 7, Ubuntu, Debian plus a swap partion, all in all 4 partitions? Lets say I have 2 disks, each 640 GB and make room - 300 GB for Windows 7, 160 GB Ubuntu, 160 GB Debian and the rest for swap 20 GB. Where do I make these partitions, do I first make one big raid array 1 in BIOS and then partition when Windows 7 is installed or do I already in BIOS make these 4 partitions?

    Read the article

  • How to run 2 SSD drives in RAID-0?

    - by jasondavis
    I am wanting to replace my Operating sytem hard drive with 2 SSD drives. Well possibly just 1 but I am curious about doing 2 in a RAID-0 setup for even more improved speed. What exactly would I need to run 2 SSD drives in a raid0 setup?

    Read the article

  • mount another drive to the same directory

    - by Ken Autotron
    I recently purchased a server that was advertised as 2TB (2 1TB drives) in size, when I use it it reports only one of the drives, I would like to be able to use both as if one drive. here is the specs... sudo lshw -C disk *-disk description: ATA Disk product: TOSHIBA DT01ACA1 vendor: Toshiba physical id: 0.0.0 bus info: scsi@1:0.0.0 logical name: /dev/sda version: MS2O serial: 13EJ81XPS size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=0005b3dd *-disk description: ATA Disk product: TOSHIBA DT01ACA1 vendor: Toshiba physical id: 0.0.0 bus info: scsi@4:0.0.0 logical name: /dev/sdb version: MS2O serial: 13OX3TKPS size: 931GiB (1TB) capabilities: partitioned partitioned:dos configuration: ansiversion=5 signature=00030e86 and fdisk -l Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030e86 Device Boot Start End Blocks Id System /dev/sdb1 * 4096 41947135 20971520 fd Linux raid autodetect /dev/sdb2 41947136 1952468991 955260928 fd Linux raid autodetect /dev/sdb3 1952468992 1953519615 525312 82 Linux swap / Solaris Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005b3dd Device Boot Start End Blocks Id System /dev/sda1 * 4096 41947135 20971520 fd Linux raid autodetect /dev/sda2 41947136 1952468991 955260928 fd Linux raid autodetect /dev/sda3 1952468992 1953519615 525312 82 Linux swap / Solaris Disk /dev/md2: 978.2 GB, 978187124736 bytes 2 heads, 4 sectors/track, 238815216 cylinders, total 1910521728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/md1: 21.5 GB, 21474770944 bytes 2 heads, 4 sectors/track, 5242864 cylinders, total 41942912 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table is it possible to mount both drives to say /Home/ so I would have 2TB of usable space?

    Read the article

  • Can't access my accelerated hard disk from msdos after installing linux on ssd cache

    - by Chibueze Opata
    I mistakenly installed Ubuntu on my ssd (forgot my PC actually came with one), when it detected a ~31GiB disk that it wanted to install to, I was a bit confused since I had brought out 30Gb in my primary disk for it, but I clicked continue. After installation, I tried to boot back into my Windows and it brought out some Intel Raid Disk Utility stuff saying I should disable acceleration on a disk something couldn't be found, I canceled it but whatever I tried, recovery tools, setups etc, I couldn't just access the drive which was apparently using the SSD as cache. Since then I've been stuck. I tried setting the 'raid' flag to the disk from 'gParted', still I couldn't. I tried the diskraid utility from windows recover disk, it said it couldn't detect any raid, diskpart sees the partition but doesn't see the volume, when I remove the raid flag, it sees the volume as one of raw type, and I can't access anything. I can however mount the drive from terminal in Ubuntu and access my files, but I don't have any backup media at the moment so I can do a factory re-install. Please how do I go about solving the issue, precisely I would like to know how to boot into the drive again. Thanks!

    Read the article

  • Can I install new version of Ubuntu in spair RAIDed partition with unetbootin

    - by artfulrobot
    I have Ubuntu 11.04 running on my home desktop which has 2 hard drives mirrored by RAID. The drives are partitioned with a big data partition, a swap partition and a couple of 20Gb partitions for OSes, one is 11.04 which is in use, and the other is kept spare for installing a later version. Which is what I'd like to do now. The idea of a 2nd partition for new OS is that I can try it, and if it's problematic, I can boot back into the original one - the machine is shared with others, so I need it to stay available! I have had horrible problems with software RAID after using a Live USB stick - basically it messes up the internal numbering of the RAID drives or something, anyway, the result is you can't boot after using it :-( and have to spend ages re-assembling the arrays, trying to remember grub commands etc etc. Quite a shocker when you consider booting from a Live USB is supposed not to affect the existing system. As I'm installing in a RAIDed disc, I would typically use the Alternative install (sad to hear that this is going to be dropped in future). However, I think I might be able to use unetbootin to trick the system into working on top of the existing system that understands RAID, with the normal ISO? If unetbootin loads from drives that are already understood to be RAIDED, then presumably it will only see md0... instead of sda, sdb... and as long as I don't need to repartition (I don't) it should be fine, right? Or is that just plain foolishness? Please tell me before I end up with a dead system (again!)

    Read the article

  • Hard time installing Ubuntu

    - by Nick
    I have a MSI GT780DXR that currently is booting windows 7. I've been trying to dual boot windows 7 and ubuntu for some time now. Here's specs that I think would make a difference Windows 7 500GB*2 RAID 0 hard drives. (Hardware RAID I'm not sure if it's a dedicated RAID card though) 7200RPM Nvidia GT570M Background: I tried to install 12.04 (64 bit) a few times but the Desktop live cd and pendrive boots with a black screen. I've tried wubi but it boots to a black screen as well. I then tried the alternative 12.04 (64 bit) and went through the installation all the way til partitioning. I let Ubuntu notice the raid setup and I setup my swap, /, and home drives, I used my free space to create the three partitions. I tried to resize the windows drive and it told me I couldn't and to be happy with my current setup. When I finally got past I got an error on installing GRUB 2 and decided to skip it and continued on to finish installation. When I tried to boot up I got an invalid partition table error. Windows recovery disc, and a GPARTED live cd couldn't find any hard drives. I ended up following advice and typed this into the recovery command prompt. bootrec /fixmbr bootrec /fixboot bootrec /rebuildBcd It worked and here I am now. The question is, how would I be able to dual boot windows 7 and Ubuntu 12.04 with this information? Thanks,

    Read the article

  • Non-volatile cache RAID controllers: what kind of protection is there against NVCACHE failure?

    - by astrostl
    The battery back-up (BBU) model: admin enables write-back cache with BBU writes are cached to the RAID controller's RAM (major performance benefit) the battery saves uncommitted and cached data in the event of a power loss (reliability) If I lose power and come back within a day or so, my data should be both complete and uncorrupted. The downside to this is that, if the battery is dead or low, OR EVEN IF IT IS IN A RELEARN CYCLE (drain/charge loops to ensure the battery's health), the controller reverts to write-through mode and performance will suffer. What's more, the relearn cycles are usually automated on a schedule which may or may not happen in the middle of big traffic. So, that has to be manually disabled and manually scheduled for off-hours if it's a concern. Annoying either way. NV caches have capacitors with a sufficient charge to commit any uncommitted-to-disk data to flash. Not only is that more survivable in longer loss situations, but you don't have to concern yourself with battery death, wear-out, or relearning. All of that sounds great to me. What doesn't sound great to me is the prospect of that flash module having an issue, though. What if it's completely hosed? What if it's only partially hosed? A bit corrupted at the edges? Relearn cycles can tell when something like a simple battery is failing, but is there a similar process to verify that the flash is functional? I'm just far more trusting of a battery, warts and all. I know the card's RAM can fail, the card itself can fail - that's common territory, though. In case you didn't guess, yeah, I've experienced a shocking-to-me amount of flash/SSD/etc. failure :)

    Read the article

  • getJSON not working if the mvc model view controller has a parameter

    - by Paul
    I'm having an issue with a callback. I'm not even getting an error in Firebug. If I alert before and after the getjson call both alerts show but the getjson call doesn't fire. public ActionResult TestPage() { return View(); } public ActionResult LoadMapLonLats(int mapId) { //some code return Json(_myMaps); } $("#Search").click(function() { $.getJSON("LoadMapLonLats", { mapId: 73 }, loadDbMap); }); function loadDbMap(maps) { alert('m'); $.each(maps, function(i) { alert(maps[i]); }); } As long as I leave TestPage without a parameter is works. If I add a parameter to TestPage(int id) then the call back to LoadMapLonLats doesn't work. Seems odd. Of course TestPage is the page I'm loading so I need to do some work here before rendering the page. Not sure why adding a parameter to the view would break the callback to another function. //this breaks he callback to LoadMapLonLats public ActionResult TestPage(int id) { return View(); } Any ideas? Seems like this may be related, if not sorry I can post a new thread.

    Read the article

  • Hide a view controller's view while flipping a view

    - by phonydev
    I have 3 views in my app. Main view has 2 buttons and when selected it displays 2nd view(which again has buttons and displays a 3rd view with images). I have a home button on second view. When pressed I want to show the main view. I can do this if I add the 2nd view as subview [self.view addSubview:secondViewController.view] But whenever 2nd view flips to display the 3rd view, I can see the main view while it is flipping. Now if I add 2nd view as below self.view = secondViewController.view then I dont have the main view to display when the home button is pressed. How can I hide the main view when 2nd view is flipping to show 3rd view?

    Read the article

  • Not able to save extjs combo using grails controller

    - by abhi
    Hi all, I am a newbie to grails/extjs I am developing a web based config tool for my team .My issue is with comboboxes of extjs I have three remote comboxes(many to one hibernate mappng).I am using hiddenName to submit its value field(which is id primay key of database) instead of its display field which is name which i get by rendering it as json.some how I see that if I select diff index other than which is loaded from db and try updating it.it definitely sends it as params but in save method of grails its not updated. I want to understand Why? I have pasted snippetof both combobox and grails method? { xtype : 'combo', id:'cpsServerid', fieldLabel : 'CpsServer', name : 'cpsServer', //hiddenId:'cpsID', hiddenName:'cpsID', store: cpsServerStore, displayField:'NAME', valueField:'ID', editable:true, typeAhead:true, mode:'remote', triggerAction:'all', width:300, autoScroll:true, selected:name, selectOnFocus:true}, GRAILS SAVE def saveApplicationSubscription = { println "saveApplicationSubscription, params = $params" ApplicationSubscription subscription if (params.id) { subscription = ApplicationSubscription.get(params.id as int) subscription.cpsServer = CpsServer.get(params.cpsID as int) subscription.topic = params.topic subscription.description = params.description subscription.subscriberApplication = SubscriberApplication.get(params.subAppID as int) subscription.outputQueue = OutputQueue.get(params.outputID as int) bindData(subscription , params) } else { params.id = 0 subscription = new ApplicationSubscription(params) subscription.id = params.id as int subscription.cpsServer = CpsServer.get(params.cpsID as int ) subscription.topic = params.topic subscription.description = params.description subscription.subscriberApplication = SubscriberApplication.get(params.subAppID as int) subscription.outputQueue = OutputQueue.get(params.outputID as int) // subscription.messageFormat = params.messageFormat } if (subscription.save()) { log.info("Saved ApplicationSubscription $subscription") render([success: true] as JSON) } else { log.info("Failed to save ApplicationSubscription $subscription, errors = ${subscription.errors}") render([success: false, errors: subscription.errors] as JSON) } } I would really apperciate any help

    Read the article

  • asp.net mvc post variable to controller

    - by Erwin
    Hello fellow programmer I came from PHP language(codeigniter), but now I learning ASP.Net MVC :) In PHP codeigniter we can catch the post variable easily with $this->input->post("theinput"); I know that in ASP.Net MVC we can create an action method that will accepts variable from post request like this public ActionResult Edit(string theinput) Or by public ActionResult Edit(FormCollection formCol) Is there a way to catch post variable in ASP.Net like PHP's codeigniter, so that we don't have to write FormCollection object nor have to write parameter in the action method (because it can get very crowded there if we pass many variable into it) Is there a simple getter method from ASP.Net to catch these post variables?

    Read the article

  • ASP.NET MVC Controller parameter processing

    - by Leonardo
    In my application I have a string parameter called "shop" that is required in all controllers, but it needs to be transformed using code like this: shop = shop.Replace("-", " ").ToLower(); How can I do this globally for all controllers without repeating this line in over and over? Thanks, Leo

    Read the article

  • Codeigniter: db data in controller

    - by Kevin Brown
    I'm confused about what to do... I'm working on a user's page where they can view certain things only if their supervisor has given them "money" or "credits". I need a simple way to get the person that is their supervisor by doing something like: $data['employer'] = $this->home_model->getEmployees(array('user_id'=>$manager_id)); Basically, get the user information about a person who's user_id matches the manager_id of the currently logged in member. I don't know how to set the variable $manager_id. Additional Information: The current user has an id, and a manager_id. I need the id of the manager. So, I need to grab the manager_id of the logged-in user and find the manager who's user_id is that of the manager_id. What's the process to do this? I can get each individually, but I don't know how to use one to get the other... I know it is confusing, but I'm confused! Thanks for the help!

    Read the article

  • Rails controller

    - by Asso
    Hello everyone! Newb in Rails i Have this problem that i cannot figure out. I've followed the sample blog dimostration form the ruby doc but now i have a problem. Let's say that in the app index page for each post i also want to show the first comment of that post. sure i need to cycle all the post to get the post id but how can i get the first comment of that post? how can i manage the homeController and the view ? thanks since now!

    Read the article

  • Overloading Controller Actions

    - by DaveDev
    Hi Guys I was a bit surprised a few minutes ago when I tried to overload an Action in one of my Controllers I had public ActionResult Get() { return PartialView(/*return all things*/); } I added public ActionResult Get(int id) { return PartialView(/*return 1 thing*/); } .... and all of a sudden neither were working I fixed the issue by making 'id' nullable and getting rid of the other two methods public ActionResult Get(int? id) { if (id.HasValue) return PartialView(/*return 1 thing*/); else return PartialView(/*return everything*/); } and it worked, but my code just got a little bit ugly! Any comments or suggestions? Do I have to live with this blemish on my Controllers? Thanks Dave

    Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >