Search Results

Search found 3695 results on 148 pages for 'failure'.

Page 35/148 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• How to resolve a "driver failure" error in the Cisco VPN client connecting from a Windows 7 client

  - by JosephStyons

  I have recently upgraded my laptop from Windows Vista SP1 to Windows 7 Professional. After the upgrade, if I try to use the Cisco VPN client to connect to a network, I get this message: Secure VPN Connection terminated locally by the Client. Reason 440: Driver Failure. Prior to the upgrade, I was able to connect with no problems. The version of the client I am using is 5.0.05.0290.

  Read the article

• Software Raid 10 corrupted superblock after dual disk failure, how do I recover it?

  - by Shoshomiga

  I have a software raid 10 with 6 x 2tb hard drives (raid 1 for /boot), ubuntu 10.04 is the os. I had a raid controller failure that put 2 drives out of sync, crashed the system and initially the os didnt boot up and went into initramfs instead, saying that drives were busy but I eventually managed to bring the raid up by stopping and assembling the drives. The os booted up and said that there were filesystem errors, I chose to ignore because it would remount the fs in read-only mode if there was a problem. Everything seemed to be working fine and the 2 drives started to rebuild, I was sure that it was a sata controller failure because I had dma errors in my log files. The os crashed soon after that with ext errors. Now its not bringing up the raid, it says that there is no superblock on /dev/sda2, even if I assemble manually with all the device names. I also did a memtest and changed the motherboard in addition to everything else. EDIT: This is my partition layout Disk /dev/sdb: 2000.4 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders, total 3907029168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0009c34a Device Boot Start End Blocks Id System /dev/sdb1 * 2048 511999 254976 83 Linux /dev/sdb2 512000 3904980991 1952234496 83 Linux /dev/sdb3 3904980992 3907028991 1024000 82 Linux swap / Solaris All 6 disks have the same layout, partition #1 is for raid 1 /boot, partition #2 is for raid 10 far plan, partition #3 is swap, but sda did not have swap enabled EDIT2: This is the output of mdadm --detail /dev/md1 Layout : near=1, far=2 Chunk Size : 64k UUID : a0feff55:2018f8ff:e368bf24:bd0fce41 Events : 0.3112126 Number Major Minor RaidDevice State 0 8 34 0 spare rebuilding /dev/sdc2 1 0 0 1 removed 2 8 18 2 active sync /dev/sdb2 3 8 50 3 active sync /dev/sdd2 4 0 0 4 removed 5 8 82 5 active sync /dev/sdf2 6 8 66 - spare /dev/sde2 EDIT3: I ran ddrescue and it has copied everything from sda except a single 4096 byte sector that I suspect is the raid superblock EDIT4: Here is some more info too long to fit here lshw: http://pastebin.com/2eKrh7nF mdadm --detail /dev/sd[abcdef]1 (raid1): http://pastebin.com/cgMQWerS mdadm --detail /dev/sd[abcdef]2 (raid10): http://pastebin.com/V5dtcGPF dumpe2fs of /dev/sda2 (from the ddrescue cloned drive): http://pastebin.com/sp0GYcJG I tried to recreate md1 based on this info with the command mdadm --create /dev/md1 -v --assume-clean --level=10 --raid-devices=6 --chunk=64K --layout=f2 /dev/sda2 missing /dev/sdc2 /dev/sdd2 missing /dev/sdf2 But I can't mount it, I also tried to recreate it based on my initial mdadm --detail /dev/md1 but it still doesn't mount It also warns me that /dev/sda2 is an ext2fs file system but I guess its because of ddrescue

  Read the article

• Boot failure : No DEFAULT or UI configuration directive found!

  - by user12378

  I've tried to install Ubuntu on a VMWare Virtual Machine, but it never get's past the bootloader : ISOLINUX 4.01 debian-20100714 ETCD Copyright (C) 1994-2010 H. Peter Anvin et al No DEFAULT or UI configuration directive found! boot: _ I've also tried to burn this .iso image to a CD and go from there - but I got the same problems also ... Some more details : VMWare Server 2.0.2 Build 203138 on Windows 2008 R2 ubuntu-10.10-desktop-i386.iso image used (downloaded yesterday evening) I have no clue, why this is not booting !!! Somebody have any ideas ? Thanks, Sven

  Read the article

• Boot failure : No DEFAULT or UI configuration directive found!

  - by Sven

  Hello .... I've tried to install Ubuntu on a VMWare Virtual Machine, but it never get's past the bootloader : ISOLINUX 4.01 debian-20100714 ETCD Copyright (C) 1994-2010 H. Peter Anvin et al No DEFAULT or UI configuration directive found! boot: _ I've also tried to burn this .iso image to a CD and go from there - but I got the same problems also ... Some more details : VMWare Server 2.0.2 Build 203138 on Windows 2008 R2 ubuntu-10.10-desktop-i386.iso image used (downloaded yesterday evening) I have no clue, why this is not booting !!! Somebody have any ideas ? Thanks, Sven

  Read the article

• How to work around a possible XNA Game Studio or Windows Phone SDK install failure on Windows 8

  - by Laurent Bugnion

  I am not sure if you guys know Aaron Stebner. Aaron works at Microsoft, and has pulled thorns from my side many many times already. His blog is at http://blogs.msdn.com/b/astebner and it is a gold mine of tips and tricks to debug and solve many cryptic issues happening during installation and removal of programs. For example, Aaron taught me how to remove programs that do not appear in the Programs and Features list, amongst many other things. The last nugget I used from Aaron’s blog saved my butt just before a presentation where I had to run both Visual Studio 10 with the Windows Phone SDK, and Visual Studio 11 for WinRT development. Of course this had to be on Windows 8. Unfortunately when you install the Windows Phone SDK on Windows 8, you may (or may not, I saw both scenarios) encounter an issue with XNA, and the installation fails. Unfortunately, even if you don’t use XNA in your apps, this will prevent even normal Windows Phone app development. Fortunately, Aaron has a fix for that. I hope that this helps spread the word, and increase Aaron’s blog’s visibility! Happy coding, Laurent   Laurent Bugnion (GalaSoft) Subscribe | Twitter | Facebook | Flickr | LinkedIn

  Read the article

• Are there any actual case studies on rewrites of software success/failure rates?

  - by James Drinkard

  I've seen multiple posts about rewrites of applications being bad, peoples experiences about it here on Programmers, and an article I've ready by Joel Splosky on the subject, but no hard evidence of case studies. Other than the two examples Joel gave and some other posts here, what do you do with a bad codebase and how do you decide what to do with it based on real studies? For the case in point, there are two clients I know of that both have old legacy code. They keep limping along with it because as one of them found out, a rewrite was a disaster, it was expensive and didn't really work to improve the code much. That customer has some very complicated business logic as the rewriters quickly found out. In both cases, these are mission critical applications that brings in a lot of revenue for the company. The one that attempted the rewrite felt that they would hit a brick wall at some point if the legacy software didn't get upgraded at some point in the future. To me, that kind of risk warrants research and analysis to ensure a successful path. My question is have there been actual case studies that have investigated this? I wouldn't want to attempt a major rewrite without knowing some best practices, pitfalls, and successes based on actual studies. Aftermath: okay, I was wrong, I did find one article: Rewrite or Reuse. They did a study on a Cobol app that was converted to Java.

  Read the article

• Failure to Boot 12.04 on HP AMD Dual Core. Rescue Mode doesn't even come up

  - by L R Bellmore Jr

  I have 12.04 installed on HP 64 bit dual core AMD laptop.. worked great until about 1-2 months ago.. now takes 1/2 hour to 25 hours to boot if it ever does. A minor number of times I get the HP logo with hash lines on screen and it just hangs... When it finally boots 95% it will run until I turn it off days later to see if any of the upgrades fixed the problem. Currently, if it boots, it is random.. .left on over night .. 2 nights ago and came back to a HP logo with Hash Lines horizontal across the screen.. frozen.. rebooted back to black screen.. no HP logo... Most often when it does boot.. no HP logo.. just cursor shows up.. and then I know it will finally load... computer has been made worthless and it is my work computer..HELP PLEASE... Rescue Mode can't be invoked.. computer doesnt respond.. has shown up 3 times in about 100 and when I have tried it... 1 time it resulted in a boot up but then failed in a couple hours.

  Read the article

• Ubuntu 12.04. Compiz Failure. Computer has nothing to use

  - by Teddy

  I updated to Ubuntu 12.04 with Compiz..now Compiz is failing and I have no tool bars or ways of getting to applications except for firefox from a link presented from sending an error report. How am I supposed to: Fix this mess with no navigation to get to the terminal, or software center. When will this problem be fixed? When I updated the system why didn't it change me back to the crappy Unity interface (No offense). If it can't be fixed how do I get my files back?

  Read the article

• Network doesn't work after installing Ubuntu 10.10. Is this a hardware failure?

  - by Septagram

  Recently I installed Ubuntu 10.10 on my dev box, making a dual boot with Windows XP. Before installation, everything worked fine, but now Windows XP cannot connect to the network saying that cable is not connected. I tried connecting it to different devices, and it always fails. Under Ubuntu I observe the same issue, but occasionally, usually it works and sometimes it can't find the network. Do you people think it's Ubuntu related, or is my network card broken?

  Read the article

• Live cd and usb install failure blank screen when trying to install on an HP Pavilion dv6

  - by Ajian

  I recently bought a new computer, and have been trying to install linux on it, 11.10 x64. It is a HP pavilion dv6-6117dx. 2.4GHz/1.5GHz VISION A8 Technology from AMD with AMD Quad-Core A8-3500M Accelerated Processor AMD Radeon HD 6620G Discrete-Class Graphics I am pretty sure i picked a unsupported graphics card or something. I have tried booting from usb as well, but the screen becomes blank after rebooting.

  Read the article

• How can I write my code to attempt a database action but continue executing code on failure?

  - by Chris

  Simple question I guess, I want to use PHP to write an update to an existing row in my database, if it doesn't happen I want to log the failure but continue executing the code. While it would be nice to have records of failures to track down issues, that the update failed isn't that important to my user, nor will it affect the running of any other code; the query is simply for a 'cosmetic' but entirely unnecessary piece of information. My database class's query function is set to die on failure, could I modify that or is there another way of doing it without altering my standard query code?

  Read the article

• PCI scan failure for SSL Certificate with Wrong Hostname?

  - by Rob Mangiafico

  A client had a PCI scan completed by SecurityMetrics, and it now says they failed due to the SSL certificate for the SMTP port 25 (and POP3s/IMAPS) not matching the domain scanned. Specifically: Description: SSL Certificate with Wrong Hostname Synoposis: The SSL certificate for this service is for a different host. Impact: The commonName (CN) of the SSL certificate presented on this service is for a different machine. The mail server uses sendmail (patched) and provides email service for a number of domains. The server itself has a valid SSL certificate, but it does not match each domain (as we add/remove domains all the time as clients move around). Seems SecurityMerics is the only ASV that marks this as failing PCI. Trustwave, McAfee, etc... do not see this as failing PCI. Is this issue truly a PCI failure? Or is it just SecuritMetrics being wrong?

  Read the article

• Hyper-V Boot failure on VHD made with Acronis?

  - by gary

  hoping someone can advise on my problem, I am running Hyper-V core and trying to create my first VM for testing purposes. Using Acronis True Image echo server with UR I converted a Seerver 2000 tib to VHD. I then copied this across to the Hyper-V local drive and created a new VM pointing the hard drive to the vhd image. When I boot this up all I get is "Boot failure. Reboot and Select proper Boot device or Insert Boot media in selected Boot device". The original server had SCSI disks, the Hyper-V server doesn't, but I have ensured that it boots from an IDE disk and that it is in fact booting from that not the CD. I can only imagine this is caused by the SCSI disks on VHD but cannot for the life of me work out how to fix, I have several of these I need to do so starting to worry now! I can confirm that when I did this from tib to vmdk it worked first time using VMware on a laptop. Any help very much appreciated. Gary

  Read the article

• Why PC reboots when there’s a power failure even with UPS?

  - by Jamil

  I've purchased a Line Interactive UPS 1200VA. It's supposed to give 8~20min backup (as written in the manual). This UPS has transfer time < 10ms. It works fine when the mains is active. But the problem is that when the power went off, the PC also went off for a fraction of a second and started rebooting. The strangest thing though is that it has to be a proper power failure by the service supplier. If I just turn off the power at the wall plug, the UPS kicks in immediately and the PC carries on working fine. What's the solution of that? What should I do? My hard drive was physically damaged because of improper shut down & restart. I've 5~8 times power outage in my country so I badly need an UPS.

  Read the article

• single point of failure in IIS Web Farm Framework setting?

  - by aamir sajjad

  ASP.NET WEB API Windows Server 2008 R2/IIS 7.5/Web Farm Framework 2.5 I am planning to deploy application across 4 web servers. Should i use shared content/configuration using DFS among web servers for web farm scenario? Second option is to use Web Farm Framework for deployment. Furthermore, is there chance of single point of failure in WFF? for example what if primary server goes down. which option would be better? pros and cons of each of the above. I appreciate your response.

  Read the article

• yum install php-tidy - no more mirrors

  - by Lylo

  Hi im trying to get the tidy extensions installed on centos running php 5.3 Thanks Downloading Packages: http://repo.webtatic.com/yum/centos/5/x86_64/php-tidy-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-pdo-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-mysql-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-gd-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-xml-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-common-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-devel-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. http://repo.webtatic.com/yum/centos/5/x86_64/php-cli-5.3.5-1.w5.x86_64.rpm: [Errno 14] HTTP Error 404: Not Found Trying other mirror. Error Downloading Packages: php-tidy-5.3.5-1.w5.x86_64: failure: php-tidy-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-cli-5.3.5-1.w5.x86_64: failure: php-cli-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-5.3.5-1.w5.x86_64: failure: php-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-pdo-5.3.5-1.w5.x86_64: failure: php-pdo-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-devel-5.3.5-1.w5.x86_64: failure: php-devel-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-mysql-5.3.5-1.w5.x86_64: failure: php-mysql-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-common-5.3.5-1.w5.x86_64: failure: php-common-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-xml-5.3.5-1.w5.x86_64: failure: php-xml-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try. php-gd-5.3.5-1.w5.x86_64: failure: php-gd-5.3.5-1.w5.x86_64.rpm from webtatic: [Errno 256] No more mirrors to try.

  Read the article

• page allocation failure - am I running out of memory?

  - by mfriedman

  Lately I've noticing entries like this one in the kern.log of one of my servers: Feb 16 00:24:05 aramis kernel: swapper: page allocation failure. order:0, mode:0x20 This is what I'd like to know: What exactly does that message mean? Is my server running out of memory? The swap usage is quite low (less than 10%), and so far I haven't noticed any processes being killed because of lack of memory. Additional information: The server is a Xen instance (DomU) running Debian 6.0 It has 512 MB of RAM and a 512 MB swap partition CPU load inside the virtual machine shows an average of 0.25

  Read the article

• Red Hat cluster: Failure of one of two services sharing the same virtual IP tears down IP

  - by js01

  I'm creating a 2+1 failover cluster under Red Hat 5.5 with 4 services of which 2 have to run on the same node, sharing the same virtual IP address. One of the services on each node needs a (SAN) disk, the other doesn't. I'm using HA-LVM. When I shut down (via ifdown) the two interfaces connected to the SAN to simulate SAN failure, the service needing the disk is disabled, the other keeps running, as expected. Surprisingly (and unfortunately), the virtual IP address shared by the two services on the same machine is also removed, rendering the still-running service useless. How can I configure the cluster to keep the IP address up?

  Read the article

• On booting my laptop warns me about failure of hard disk is imminent...can it be repaired or to be replaced..?

  - by nrb

  when I am booting my laptop (Lenovo G550) it gives an error message prior to that.. SMART Failure Predicted on Hard Disk O:Hitachi HTS543225l9A300-(PM) Warning : Immediately back up your data and replace your hard disk drive. Afailure may be imminent. Press F1 to continue.. Once it started, it runs smoothly, I also verified its status by running some internal HDD tests by Hard Disk Senitel software..It shows no bad sector , no virus, no damage , normal temperature ... it suggests every thing is OK except its health... Now my question is that then what is the wrong with it..? It may be wrong with plates (dusty) or the read/write heads...then can I go for repair it or replace it...? My system now reminds me every half an hour to resolve this problem since last 10 days... Help me.

  Read the article

• GMail IMAP + Apple Mail / iPhone - "Account exceeded bandwidth limits. (Failure)"

  - by bpapa

  Started seeing this this morning in Apple Mail. I have one of those exclamation point error indicators next to "Inbox", with this error message when I click on it: There may be a problem with the mail server or network. Verify the settings for account “IMAP Account” or try again. The server returned the error: Account exceeded bandwidth limits. (Failure). This is in Snow Leopard. I'm using GMail IMAP, and I am way below the size quota - I've never heard of there even being a bandwidth quota. I'm also not getting mail from the same account to the mail app on my iPhone. EDIT - a month later I'm seeing this, and I'm thinking of just switching Mobile Me. EDIT AGAIN - Making community wiki. I stopped seeing the problem once I updated Snow Leopard to the latest version, but since others continue to see it...

  Read the article

• Not all of your nameservers are in different subnets. Single point of failure

  - by user2118559

  Using VPS hosting and dynadot (domain registrar) DNS. Checked domain name with http://www.intodns.com and get some warnings Different subnets WARNING: Not all of your nameservers are in different subnets and Different autonomous systems WARNING: Single point of failure As understand to avoid the warning must have second Ip4 address and both the addresses must point to different servers? If both Ip addresses point to the same server, it does not help? I mean each server has own Ip address. If one server down, then visitors can access website (files) on another server? Is this the reason why need more than one Ip? Tried to point website to 2 ip addresses and after some time get warning from uptimerobot Connection Timeout

  Read the article

• Why do I get "General Failure" when pinging host name on a Win 7 node on the network?

  - by hydroparadise

  This is a very peculiar problem with a station on our network. The client pc is running Windows 7 Pro. What makes this problem interesting is that this client is the only node on the network that seems to be experiencing this proglem. When I try to ping a specific Win 08 server by host name, I get an IPv6 address and get General failure. But when I ping it's IPv4 address, it responds just fine. My first thought would check the DNS server the name resolutions to see what would be going on, but the problem begs the quesion, why does the station get an IPv6 address back and fails as opposed to using the IPv4 settings (which are static btw). What gives? I am including a screen shot of trying the one specific server and failing while trying another server with success. All other nodes on the network don't have problems communicating with the server the one station is having issues with.

  Read the article

• What happens with the Guest OS's on ESXi in the event of a power failure?

  - by Jeremy Holovacs

  Many small businesses would prefer to let their server drop on power failure than to pay even $100 for a cheap UPS. It's often difficult to convince them of the value of something like that; it's why they like ESXi. It's free, they can save a lot of cash by putting a bunch of linux servers on one machine, and then I get paid. :) If the ESXi server experiences a power outage, it is set to come back on automatically when power is restored. What happens with the guest OS's? Ideally I would like them to all come online again as well, assuming they were on when power was lost, but I see no option for choosing this. I don't want to yank power to the system just to try it out, of course. I'm sure someone knows what happens by default, and perhaps how to make my system to work as I would wish.

  Read the article

• LAMP Server without single failure point + Global Server Load Balancing?

  - by José Nobile

  I want implement a LAMP Server (Linux Apache MySQL PHP) without a single failure point and with Global Server Load Balancing. I have a server in Cali, Colombia, and other server will be installed in Melbourne, Australia, user in America can use the Cali Server and in Europe, Asia, Africa or Oceania use the Melbourne Server. If any server fail (or load is excessively high), a server must answer all request. Data in MYSQL must be in sync, php files, any configuration in both server must be in sync. I read about of Google DNS Server 8.8.8.8 and 8.8.4.4 and ANY Cast, also about MySQL semisynchronous replication and MySQL Cluster, but what about other things, as crontabs, and the configurations in server? The solution can't depend of APNIC or BGP, only open source software running in Linux.

  Read the article

• Dealing with LDAP failure when using it for PAM/NSS?

  - by Insyte

  I use a redundant pair of OpenLDAP servers for PAM auth and directory services via NSS. It's been 100% reliable so far, but nothing runs flawlessly forever. What steps should I take now so I have a fighting chance of recovering from failure of the LDAP server(s)? In my informal testing, it appears that even already authenticated shells are largely useless as all username/uid lookups hang until the directory server comes back. So far I've come up with only two things: Do not use NSS-LDAP and PAM-LDAP on the LDAP servers themselves. Create a root-level account on all boxes that only accepts publickey authentication from our local subnet and protect that key well. I'm not sure how much good this would do me as once I'm logged in, I suspect I wouldn't be able to accomplish anything since all the userid lookups would be hanging. Any other suggestions?

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >