Search Results

Search found 3312 results on 133 pages for 'freebsd ports'.

Page 35/133 | < Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >

• Enabling "USB Printing Support" in Windows 7

  - by Kevin Dente

  I'm trying to use an old parallel-port based printer with a USB-to-parallel port adapter on Windows 7. When I plug it into the USB port on the computer it's listed as an unrecognized device. I know that these cables typically use the "USB Printing Support" driver with makes USB ports show up as printer ports in the printer dialog. Is there a way to manually add USB Printing Support to Windows 7, since it isn't being added automatically?

  Read the article

• Enabling "USB Printing Support" in Windows 7

  - by Kevin Dente

  I'm trying to use an old parallel-port based printer with a USB-to-parallel port adapter on Windows 7. When I plug it into the USB port on the computer it's listed as an unrecognized device. I know that these cables typically use the "USB Printing Support" driver with makes USB ports show up as printer ports in the printer dialog. Is there a way to manually add USB Printing Support to Windows 7, since it isn't being added automatically?

  Read the article

• Impossible to Remove FTDI driver / FTDI Enumeration on Windows 7

  - by Joe

  I have already read the : Is it possible to reset FTDI virtual com ports enumeration, we easily get hundreds of COM ports in production environment topics which was pretty interesting ! But I got a problem, apparently I can't delete the ftdi driver, so I can't use the previous conclusion of the topic... I'm really stuck and bored of this problem, my com port number is 132 ! Does someone have another solution ?

  Read the article

• smtp(s) proxy to monitor outgoing spam

  - by Zulakis

  I am looking for a smtp proxy to install on our gateway which should monitor outgoing smtp traffic to identify the source of recently occuring spam attacks from our network. It would be enough if this could log all outgoing mails, no actual filtering must be done as I'm going to do this manually. Also, is it possible to monitor smtps ports 465 and 587 or is it necessary to completely block these ports to stop spam?

  Read the article

• Amazon EC2, still cant ping or "http" it

  - by DarkFire21

  I am new at Amazon Cloud technologies. I ve set up an Amazon Linux instance created my keys and assigned elastic IP. Also, I opened all TCP, UDP, ICMP ports(ok, it's very dangerous, but I am using it for test purposes). I ve also installed Apache server and enabled it. But still cant ping or access my instance via IP. Any ideas? EDIT: Please see a screenshot of the security groups settings. All ports are open... Check this out

  Read the article

• Launching waiting for xdebug session 57%

  - by Lee Timms

  Problem: In short, I am getting the "Launching waiting for xdebug session 57%" problem. I am running Eclipse Gallileo Build id: 20100218-1602 on Windows 7 Ultimate I am running php 5.3.8 The Zend Extension Build and PHP Extension Build are both - API220090626,TS,VC9 Solutions Tried: I have verified that port 9000 is available for use, I have even tried other ports as a double check that ports was not the issue. That includes setting the ports in both the php.ini file and in the Eclipse development environment. I have set the php.ini file as follows (I have also tried numerous other configurations - none worked): zend_extension = "c:/wamp/bin/php/php_xdebug-2.1.3-5.3-vc9.dll" [xdebug] xdebug.remote_enable=on xdebug.remote_host="localhost" xdebug.remote_port=9000 xdebug.remote_handler="dbgp" I am at a loss, can anyone help?

  Read the article

• Python MD5 Hash Faster Calculation

  - by balgan

  Hi everyone. I will try my best to explain my problem and my line of thought on how I think I can solve it. I use this code for root, dirs, files in os.walk(downloaddir): for infile in files: f = open(os.path.join(root,infile),'rb') filehash = hashlib.md5() while True: data = f.read(10240) if len(data) == 0: break filehash.update(data) print "FILENAME: " , infile print "FILE HASH: " , filehash.hexdigest() and using start = time.time() elapsed = time.time() - start I measure how long it takes to calculate an hash. Pointing my code to a file with 653megs this is the result: root@Mars:/home/tiago# python algorithm-timer.py FILENAME: freebsd.iso FILE HASH: ace0afedfa7c6e0ad12c77b6652b02ab 12.624 root@Mars:/home/tiago# python algorithm-timer.py FILENAME: freebsd.iso FILE HASH: ace0afedfa7c6e0ad12c77b6652b02ab 12.373 root@Mars:/home/tiago# python algorithm-timer.py FILENAME: freebsd.iso FILE HASH: ace0afedfa7c6e0ad12c77b6652b02ab 12.540 Ok now 12 seconds +- on a 653mb file, my problem is I intend to use this code on a program that will run through multiple files, some of them might be 4/5/6Gb and it will take wayy longer to calculate. What am wondering is if there is a faster way for me to calculate the hash of the file? Maybe by doing some multithreading? I used a another script to check the use of the CPU second by second and I see that my code is only using 1 out of my 2 CPUs and only at 25% max, any way I can change this? Thank you all in advance for the given help.

  Read the article

• strcmp() but with 0-9 AFTER A-Z? (C/C++)

  - by Aaron

  For reasons I completely disagree with but "The Powers (of Anti-Usability) That Be" continue to decree despite my objections, I have a sorting routine which does basic strcmp() compares to sort by its name. It works great; it's hard to get that one wrong. However, at the 11th hour, it's been decided that entries which begin with a number should come AFTER entries which begin with a letter, contrary to the ASCII ordering. They cite the EBCDIC standard has numbers following letters so the prior assumption isn't a universal truth, and I have no power to win this argument... but I digress. Therein lies my problem. I've replaced all appropriate references to strcmp with a new function call nonstd_strcmp, and now need to implement the modifications to accomplish the sort change. I've used a FreeBSD source as my base: http://freebsd.active-venture.com/FreeBSD-srctree/newsrc/libkern/strncmp.c.html if (n == 0) return (0); do { if (*s1 != *s2++) return (*(const unsigned char *)s1 - *(const unsigned char *)(s2 - 1)); if (*s1++ == 0) break; } while (--n != 0); return (0); I guess I might need to take some time away to really think about how it should be done, but I'm sure I'm not the only one who's experienced the brain-deadness of just-before-release spec changes.

  Read the article

• Problems with IRQs when connecting two digium card in and asterisk box

  - by JorgeO

  I have two Digium Wildcard TDM800P with 8 FXO ports each. When I connect both at the same time IRQ misses start showing up making my computer unresponsive and unusable. One card works fine but I need all 16 FXO ports to work to receive calls from my Telco. Is there a way for the cards to communicate with each other so they don't generate as many interrupts. Or a way to tweak Linux to dedicate separate IRQ's for each card. I have tried disabling Audio, ACPI and USB ports. Still too many IRQ misses.

  Read the article

• TCP 3 way handshake

  - by Tom

  Hi, i'm just observing what NMAP is doing for the 3 ports it reports are open. I understand what a half-scan attack is, but what's happening doesnt make sense. NMAP is reporting ports 139 are 445 are open..... all fine. But when i look at the control bits, NMAP never sends RST once it has found out the port is open, It does this for port 135- but not 139 and 445. This is what happens: (I HAVE OMITTED THE victim's replies) Sends a 2 (SYN) Sends a 16 (ACK) Sends a 24 (ACK + PST) Sends a 16 (ACK) Sends a 17 (ACK + FIN) I dont get why NMAP doesnt 'RST' ports 139 and 445??

  Read the article

• Configuring 2 XBee Modules on OSX for wireless connection

  - by Annette

  I am trying find out how and with which program for OSX (10.5.8) I can configure serial ports? I am trying to establish a wireless connection between two Xbee´s (RF modules) and cannot figure out how to use ZTerm nor screen under Terminal. The setup I am using is: an Arduino+Xbeeshield+Xbee with external power supply, and an xbee on the xbee explorer connected to the Computer via USB. I am trying to gather information on this through various forums, but most of them cover the configuration issue for PC using X-CTU (which I tried with CrossOver but it doesn´t recognize ny of my ports). According to one source, using screen under Terminal should show me all my serial ports, particularly /dev/tty.KeySerial1 - but it doesn´t show, even though I´ve plugged in both my arduino+xbee shield and the xbee on the explorer.

  Read the article

• Find mininum unused value in mysql table

  - by splattru

  I have a MySQL table like this: +--------+-------+ + Server + Port + +--------+-------+ + 1 + 27001 + +--------+-------+ + 2 + 27002 + +--------+-------+ + 4 + 27004 + +--------+-------+ How you can see - here was 27003 port - but it was deleted some time ago (just for example). Is there some way to know the minimum value that is not used (higher than 27000 for example) in mysql table? Or there is no way and I need to make an separate table with all ports and column with "used" or "not used" ? Situation explanation: I am creating game hosting website, and I can use auto-increment for ports, but I will have a lot of deleted/unused ports after some time, and I want to use all of them before increasing port range. Thanks for your answers!

  Read the article

• embedded dev. question - how to break free from a faulty serial port opening?

  - by user347266

  Under WindowsCE, C++ project, I'm trying to work with devices connected via both "real" serial ports and/or serial-to-usb wrappers ("virtual" serial ports); my problem is - when I try to open the port, if something goes wrong, the function never returns and the system goes into some non-responsive state and has to be eventually rebooted. I need to open the ports from the main thread. The question is - how can I make it happen in a controlled way?? this is the opening code snippet: std::ostringstream device_name; device_name << "\\.\COM" << port; m_port = ::CreateFile(device_name.str().c_str(), GENERIC_READ | GENERIC_WRITE, 0, // exclusive access NULL, // no security OPEN_EXISTING, FILE_FLAG_OVERLAPPED, // overlapped I/O NULL); // null template any suggestions would be greatly appreciated thanks!

  Read the article

• Concatenation awk outputs

  - by Rookie_22

  I'm using regex to parse NMAP output. I want the ip addresses which are up with the corresponding ports open. Now I've a very naive method of doing that: awk '/^Scanning .....................ports]/ {print substr ($2,1,15);}' results.txt awk '/^[0-9][0-9]/ {print substr($1,1,4);}' results.txt | awk -f awkcode.awk where awkcode.awk contains the code to extract numbers out of the substring. The first line prints all the ips that are up and 2nd gives me the ports. My problem is that I want them mapped to each other. Is there any way to do that? Even sed script would do.

  Read the article

• Object directing to a property when accessed as an iterable

  - by ThE_JacO

  I'm trying to figure out if there's an elegant and concise way to have a class accessing one of its own properties when "used" as a dictionary, basically redirecting all the methods that'd be implemented in an ordered dictionary to one of its properties. Currently I'm inheriting from IterableUserDict and explicitly setting its data to another property, and it seems to be working, but I know that UserDict is considered sort of old, and I'm concerned I might be overlooking something. What I have: class ConnectionInterface(IterableUserDict): def __init__(self, hostObject): self._hostObject= hostObject self.ports= odict.OrderedDict() self.inputPorts= odict.OrderedDict() self.outputPorts= odict.OrderedDict() self.data= self.ports This way I expect the object to behave and respond (and be used) the way I mean it to, except I want to get a freebie ordered dictionary behaviour on its property "ports" when it's iterated, items are gotten by key, something is looked up ala if this in myObject, and so on. Any advice welcome, the above seems to be working fine, but I have an odd itch that I might be missing something. Thanks in advance.

  Read the article

• Enabling SSL on apache2 causes address already in use error

  - by durron597

  My server works just fine on a normal apache2 install. Now, I'm trying to install subversion on this server using this guide: http://alephzarro.com/blog/2007/01/07/installation-of-subversion-on-ubuntu-with-apache-ssl-and-basicauth/ I get the following error: (98)Address already in use: make_sock: could not bind to address 0.0.0.0:443 When I do grep -rH 443 /etc/apache2/, I get results in two files: ports.conf and sites-enabled/default-ssl I tried it both with and without that last Listen 443 commented out, here's ports.conf: NameVirtualHost *:80 Listen 80 <IfModule mod_ssl.c> NameVirtualHost *:443 Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> #Listen 443 And the first few lines of default-ssl <IfModule mod_ssl.c> <VirtualHost *:443> ServerAdmin webmaster@localhost SSLEngine on SSLCertificateFile /this/isnt/relevant/probably.pem SSLProtocol all SSLCipherSuite HIGH:MEDIUM And netstat -an --inet | grep 443 returns nothing. Any ideas?

  Read the article

• What have we lost from computers 20 years ago

  - by Martin Beckett

  Following the theme of - I can't believe computers used floppy disks and did you have debuggers 20 years ago - questions (and because even putting my age in hex I don't look young anymore). What have we lost from computers 20years ago? VMS versioning file system. Make a mistake, no problem myprog.cpp;5 is still there. Home computers that powered up to give you a wordprocessor or a basic prompt in <0.5sec User ports, serial ports and ADCs that you could control things with - without an arduino APIs that actually did what they said (even DOS interrupts), without having to guess and experiment your way through layers of frameworks.

  Read the article

• Unicast traffic between hosts on a switch leaving the switch by its uplink. Why?

  - by Rich Lafferty

  I have a weird thing happening on our network at my office which I can't quite get my head around. In particular I can't tell if it's a problem with a switch, or a problem with configuration. We have a Cisco SG300-52 switch (sw01) in the top of a rack in our server room, connected to another SG300-28 that acts as our core switch (core01). Both run layer 2 only, our firewalls do routing between VLANs. They have a dozen or so VLANs between them. Gi1 on sw01 is a trunk port connected to gi1 on core01. (Disclosure: There are other switches in our environment but I'm pretty sure I've isolated the problem down to these two. Happy to provide more info if necessary.) The behaviour I'm seeing is limited to one VLAN, vlan 12 -- or, at least, it's not happening on the other ones I checked (It's hard to guarantee the absence of packets), and it is: sw01 is forwarding, to core01, traffic which is between two hosts which are both plugged into sw01. (I noticed this because the IDS in our firewall gave a false positive on traffic which should not reach the firewall.) We noticed this mostly between our two dhcp/dns servers, net01 (10.12.0.10) and net02 (10.12.0.11). net01 is physical hardware and net02 is on a VMware ESX server. net01 is connected to gi44 on sw01 and net02's ESX server to gi11. [net01]----gi44-[sw01]-gi1----gi1-[core01] [net02]----gi11/ Let's see some interfaces! Remember, vlan 12 is the problem vlan. Of the others I explicitly verified that vlan 27 was not affected. Here's the two hosts' ports: esx01 contains net02. sw01#sh run int gi11 interface gigabitethernet11 description esx01 lldp med disable switchport trunk allowed vlan add 5-7,11-13,100 switchport trunk native vlan 27 ! sw01#sh run int gi44 interface gigabitethernet44 description net01-1 lldp med disable switchport mode access switchport access vlan 12 ! Here's the trunk on sw01. sw01#sh run int gi1 interface gigabitethernet1 description "trunk to core01" lldp med disable switchport trunk allowed vlan add 4-7,11-13,27,100 ! And the other end of the trunk on core01. interface gigabitethernet1 description sw01 macro description switch switchport trunk allowed vlan add 2-7,11-16,27,100 ! I have a monitor port on core01, thus: core01#sh run int gi12 interface gigabitethernet12 description "monitor port" port monitor GigabitEthernet 1 ! And the monitor port on core01 sees unicast traffic going between net01 and net02, both of which are on sw01! I've verified this with a monitor port on sw01 that sees the net01-net02 unicast traffic leaving via gi1 too. sw01 knows that both of those hosts are on ports that are not its trunk port: :) ratchet$ arp -a | grep net net02.2ndsiteinc.com (10.12.0.11) at 00:0C:29:1A:66:15 [ether] on eth0 net01.2ndsiteinc.com (10.12.0.10) at 00:11:43:D8:9F:94 [ether] on eth0 sw01#sh mac addr addr 00:0C:29:1A:66:15 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:0c:29:1a:66:15 gi11 dynamic sw01#sh mac addr addr 00:11:43:D8:9F:94 Aging time is 300 sec Vlan Mac Address Port Type -------- --------------------- ---------- ---------- 12 00:11:43:d8:9f:94 gi44 dynamic I also brought up an unused port on sw01 on vlan 12, but the unicast traffic was (as best as I could tell) not coming out that port. So it doesn't look like sw01 is pushing it out all its ports, just the right ports and also gi1! I've verified that sw01 is not filling up its address-table: sw01#sh mac addr count This may take some time. Capacity : 8192 Free : 7983 Used : 208 The full configs for both core01 and sw01 are available: core01, sw01. Finally, versions: sw01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.0.0.4 ( date 08-Apr-2010 time 16:37:57 ) HW version V01 core01#sh ver SW version 1.1.2.0 ( date 12-Nov-2011 time 23:34:26 ) Boot version 1.1.0.6 ( date 11-May-2011 time 18:31:00 ) HW version V01 So my understanding is this: sw01 should take unicast traffic for net01 and send it only out net02's port, and vice versa; none of it should go out sw01's uplink. But core01, receiving traffic on gi1 for a host it knows is on gi1, is right in sending it out all of its ports. (That is: sw01 is misbehaving, but core01 is doing what it should given the circumstances.) My question is: Why is sw01 sending that unicast traffic out its uplink, gi1? (And pre-emptively: yes, I know SG300s leave much to be desired, and yes, we should have spanning-tree enabled, but that's where I'm at right now.)

  Read the article

• Beginner Geek: How to Use Multiple Monitors to Be More Productive

  - by Chris Hoffman

  Many people swear by multiple monitors, whether they’re geeks or just people who need to be productive. Why use just one monitor when you can use two or more and see more at once? Additional monitors allow you to expand your desktop, getting more screen real estate for your open programs. Windows makes it very easy to set up additional monitors, and your computer probably has the necessary ports. Why Use Multiple Monitors? Multiple monitors give you more screen real estate. Hook up multiple monitors to a computer and you can move your mouse back and forth between them, dragging programs between monitors as if you had an extra-large desktop. People who swear by multiple monitors use them to display multiple things on-screen at a time. Rather than Alt+Tabbing and task switching to glance at another window, you can just look over with your eyes and then look back to the program you’re using. Some examples of use cases for multiple monitors include: Coders who want to view their code on one display with the other display reserved for documentation. They can just glance over at the documentation and look back at their primary workspace. Anyone who needs to view something while working. Viewing a web page while writing an email, viewing another document while writing an something, or working with two large spreadsheets and having both visible at once. People who need to keep an eye on information, whether it’s email or up-to-date statistics, while working. Gamers who want to see more of the game world, extending the game across multiple displays. Geeks who just want to watch a video on one screen while doing something else on the other screen. Hooking Up Multiple Monitors Hooking up an additional monitor to your computer should be very simple. Most new computers come with more than one port for a monitor — whether DVI, HDMI, the older VGA port, or a mix. Some computers may include splitter cables that allow you to connect multiple monitors to a single port. Most laptops also come with ports that allow you to hook up an external monitor. Plug a monitor into your laptop’s DVI or VGA port and Windows will allow you to use both your laptop’s integrated display and the external monitor at once. This all depends on the ports your computer has and how your monitor connects. If you have an old VGA monitor lying around and you have a modern laptop with only DVI or HDMI connectors, you may need an adapter that allows you to plug your monitor’s VGA cable into the new port. Be sure to take your computer’s ports into account before you get another monitor for it. Managing Multiple Monitors With Windows Windows makes using multiple monitors easy. Just plug the monitor into the appropriate port on your computer and Windows should automatically extend your desktop onto it. You can now just drag and drop windows between monitors. To control how this works, right-click your Windows desktop and select Screen resolution. Choose an option from the Multiple displays box. The Extend option extends your desktop onto an additional monitor, while the other options are mainly useful if you’re using an additional monitor for presentations — for example, you could mirror your laptop’s desktop onto a large monitor or blank your laptop’s screen while it’s connected to a larger display. Be sure to arrange your monitors properly so Windows understands how your monitors are physically positioned. Windows 8 allows you to extend your Windows taskbar across multiple monitors. You’ll find this option in the taskbar’s options window — right-click the taskbar and select Properties. You can also choose where you want Windows to display taskbar buttons for open programs — on any monitor’s taskbar or only on the taskbar on the associated monitor. Windows 7 doesn’t have these convenient features built-in — your second monitor won’t have a taskbar. To extend your taskbar onto an additional monitor, you’ll need a third-party utility like the free and open-source Dual Monitor Taskbar. If you just have a single monitor, you can also use the Aero Snap feature to quickly place multiple Windows applications side by side. On Windows 7 or 8, press Windows Key + Left or Windows Key + Right to make the current window take up the left or right half of your display. You could also drag any window’s title bar to the left or right edges of your screen and release the window. How useful this feature is depends on your monitor’s size and resolution. If you have a large, high-resolution monitor, it will allow you to see a lot. If you have a smaller laptop monitor with the seemingly standard 1366×768 resolution, you won’t be able to see much of each snapped window at once, so snapping windows may not be practical. Image Credit: Chance Reecher on Flickr, Camp Atterbury Joint Maneuver Training Center on Flickr, Xavier Caballe on Flickr     

  Read the article

• Switching between ethernet interfaces on Ubuntu 10.04 SERVER

  - by Chaitanya

  I have ubuntu 10.04 "SERVER" installed on a system with two ehternet ports. I use only one at a time. I wanted to know if I can switch between ports without using ifup and ifdown every time. That means when I connect my Lan cable on eth0 it should work and it does. But when I disconnect the lan cable and connect it on eth1 I have to ifdown eth0 and only then it works. In my /etc/network/interfaces file I have configured both eth0 and eth1. there is no problem other than I have to switch it manually with ifdown and ifup everytime. Please guide. Thanks in advance

  Read the article

• usb hub not working on resume from suspend

  - by user1781498

  All the usb ports on my laptop work but when I resume from suspend some the usb ports don't work. lsusb Before Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 003 Device 002: ID 04f2:b3a6 Chicony Electronics Co., Ltd Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsusb After Suspend: Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 003: ID 04f3:014b Elan Microelectronics Corp. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

  Read the article

• Can I prevent an IDENTIFY PACKET DEVICE command to a specific device at boot?

  - by Brian Spisak

  This is related to a previous question related to installation that is now resolved. I'm opening a new question, because I still need to get my DVD drive working. Problem: Failed boot when my ASUS DRW-24B1/ST DVD drive is attached to my asmedia ASM1061. Symptom: ata8.00: exception Emask 0x52 Sact 0x0 SErr 0xffffffff action 0xe frozen ata8: SError: { blah blah } ata8.00: failed command: IDENTIFY PACKET DEVICE ata8.00: cmd blah blah res blah blah (ATA bus error) ata8.00: status: { DRDY } ata8: hard resetting link Background: The ASM1061 is a PCIe to SATA bridge providing 2 x 6Gb/s ports and is supposed to be fully compliant to SATA specs. I just discovered in the fine print of my ASUS P8Z77-V pro motherboard that "These SATA ports are for data hard drivers only. ATAPI devices are not supported." However, I have already installed Windows 7 using this drive and I can run the Ubuntu 12.04 installer from it as well. The only time I have a problem is during Ubuntu boot when it tries an IDENTIFY PACKET DEVICE which seems to be an ATAPI command. I can't simply switch this device to another SATA port because they are already allocated to other devices. (My chipset's 2 x 6Gb/s are connected to my boot SSD and a fast HDD while the 4 x 3Gb/s ports are running a RAID 5 array.) If this can't be fixed or worked around, I suppose I'll have to go buy SATA add-in card. Blech. Thoughts: If indeed this is a device specific issue (that it doesn't support ATAPI discovery) then I can't expect - is it udev? - to work with it. But, it seems that Windows and even the Ubuntu installer work just fine. So why does udev have a problem? At the end of the day, it would be nice to have the DVD working under Ubuntu, but I can live without it. But, as this is a dual-boot machine, I can't physically disconnect it because I want it to work with Windows. (And physically disconnecting it every time I want to boot Ubuntu is NOT an option. ;-) Questions: Should this be considered a bug? My feelings are that if it works with other OS that it should probably work with Ubuntu as well. How can I work around this problem? I have a limited knowledge of linux internals, but it seems I should be able to somehow tell udev (or whatever is doing the discovery) to ignore that device. Is there a way?

  Read the article

• 3+ monitors, nvidia + intel graphics

  - by gozzilli

  I have seen lots of different posts on this issue, but I cannot figure out what to do. I hope we can collect the available information in one place, so that they can be useful for others. Is it possible to have multiple (3+) monitors running on two different graphics cards? I have 1x nVidia GeForce GTX 550 with 2 DVI ports and 1x Intel integrated graphics, with 2 DVI ports. I understand that they would be running on different instances of X servers. Is that correct? Could someone point me in the right direction to start? On Windows it's so simple, there is no additional thing to do other than going in display preferences and activating all 3+ monitors. They can even be laid out alternating one monitor from one graphics card with another monitor from the other card.

  Read the article

• Configure firewall (Shorewall/UFW) to allow traffic for services on an Ubuntu Server

  - by Niklas

  I have an Ubuntu Server 11.04 x64 which I want to secure. The server will be open to Internet and I want to be able to SSH/SFTP into the machine and the SSH-server runs on a custom set port. I also want a web server accessible from the Internet. These tasks seems not to hard to perform but I also want SAMBA-shares to be accessible from within the local network and this seems to be a bit trickier. If possible I also want to be able to "stealth" the ports necessary to protect the server further but also allow the SAMBA-shares to be automatically found within the local network. I've never configured firewalls before except for a router and I always bump into a bunch of problem when doing it all by myself so I was hoping for some tips or preferably a guide on how to this. Thank you! Update: On second thought I'd could just as likely go with UFW if the same settings are achievable ("stealth" ports).

  Read the article

• Capture RTSP stream from IP Camera and store

  - by Keerthi

  I've got a few IP Cameras which output an RTSP (h264 mpeg4) stream. Hitting the URL locally via VLC: rtsp://192.168.0.21:554/mpeg4 I can stream the camera and dump to disk (on my desktop). I'd like to however store these files on my NAS (FreeNAS). I was looking at ways to capture the RTSP stream and dump them to disk but I'm unable to find anything. Is it possible to capture the stream on FreeBSD or Linux (RaspberryPi) and dump the streamed content to a disk local to Linux or FreeBSD - preferably every 30minutes? EDIT: The NAS is headless (HP N55L or something) and the RaspberryPi's are headless too. I've already looked into ZoneMinder but need something small. I was hoping maybe using Motion to detect motion on the stream but that will come later.

  Read the article

< Previous Page | 31 32 33 34 35 36 37 38 39 40 41 42  | Next Page >