Search Results

Search found 3312 results on 133 pages for 'freebsd ports'.

Page 40/133 | < Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >

  • VMware networking - PortChannel or not?

    - by dunxd
    My ESX hosts each have 8 NICS. I have set up 2 NICs for our iSCSI SAN - each is connected to a different SAN switch. 2 NICs are set up for vMotion and Service Console - these are each connected to a different core switch (ports are trunked with VLANs dedicated to vMotion and Management) I now have four ports left over. Currently we have these set up each going into our default VLAN. Two NICs are connected to one core-switch and two are connected to the other. We decided to aggregate the connections to each switch - so they are teamed at the vswitch end, and port channelled at the physical switch end. I am now reading that port channelling these connections is not particularly useful, perhaps even over complicating things. Is there a particular problem with using port channels for VMware? What method provides the best balance between redundancy and performance?

    Read the article

  • What causes winsock 10055 errors? How should I troubleshoot?

    - by Tom Kerr
    I'm investigating some issues with winsock 10055 errors on a chain of custom applications (some of which we control, some not) and was hoping to get some advice on techniques to troubleshoot the problem. No buffer space available. An operation on a socket could not be performed because the system lacked sufficient buffer space or because a queue was full. From research, non-paged pool and ports seem to be the only resources which can cause this error. Is there another resource which might cause 10055 errors? Currently, we have perfmon counters setup on the applications and non-paged pool usage looks low in most circumstances. Open TCP connections looks low and I am unaware of another way to monitor ports. Since it only happens in production, we are unable to use more invasive counters. Is there some other tool or procedure you would recommend to diagnose which application is causing the issue?

    Read the article

  • Using QoS to prioritize IP addresses

    - by Tristan
    I have a Western Digital N900 router. I was hoping I'd be able to throttle users based on their MAC address with it, which isn't possible sadly. Seems simple in principle though, duh. The battle against bandwidth hogging roomates rages on. Could I just set the local IP range to their IP, and then set the Local port range to every single port in existence. Then prioritize their IP to lower than mine? Will this work? What are all the ports? And what's the difference between Local and Remote IPs or Ports? Name: Roomate, Priority: Low, Protocol: TCP or UDP ??, Local IP Range: .101 to .101, Local Port Range: 0 to infinity, Remote IP Range: ? to ?, Remote Port Range: ? to ?

    Read the article

  • What are some of the best wireless routers for a price-conscious home power-user?

    - by Alain
    I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

    Read the article

  • HID USB Very Strange Problem...

    - by Lasanha
    I realy hope some one can help me here cause i search all over the web and nothing comes up.. I allways used PS/2 KB and Mouse and a USB KeyPad (Genius ErgoMedia 500 Gaming Explorer) to play some games, mmorpg, fps, you named, very good whit 11 keys whit possible macros etc etc... Now it comes the problem, i have a USB mouse that have 4 extra buttons, and i need more button, i love buttons.. Well, i plug in the USB mouse and disconectes de PS/2. Everything is ok until i toutch the mouse. If i do so, the ErgoMedia goes off, then on, then i mouse the mouse or press a button and all over again. Yesterday i went buying a new mouse that i liked, a USB mouse too (NPlay whit macros and all that stuff 3600dpi...) Hoping the problem was only whit the other mouse, but no.. It does the exact same thing, ErgoMedia keeps disconecting and conecting everytime i toutch the mouse. What i allready did: Update drivers of both mouses Update drivers of ErgoMedia (no specific drivers(Windows based)) Update drivers of MB Chipset (Actualy no, cause it was up to date allready) Trying other USB Ports (4 Ports back, 4 Ports Front and even 1 Port in 16 card slot device) Disable the "Allows Windows to shut down the energy bla bla" thing in Device Setings. Look up in the Device Setings only apear a problem on the ergomedia (Human interface Device) when i move the damm mouse.. Using Everest to read behavier, everything normal, exepts the disconecting thing, but no errors. Not a power suply, only the ErgoMedia and the mouse are in the USBs, and i allready disable the 16 card reader whit one usb slot to see.. Clean the IRQ registry. Look the entire internet for a fix solution. Help others problems wile looking for a fix for me (Im not a pro but not a completly stupid) Talking to you beggin you to help me as a last resorce... Machine: Acer M3641 Core2Quad 64x Based OS Vista 64b 4GbRAM HD Audio and Graphics I realy hope some one out there knows a fix for this, maybe it´s a simple thing, so simple that i´m to stupid to see that.. Sorry for my bad inglish but i write lot of erros even in my language. Any help will be very welcome. Tanks for ur concern and atention ^^

    Read the article

  • Extend my LAN network

    - by user268291
    i have a patch panel and hardwiring already setup in my office. The patch panel is 24-port and all the ports are engaged. All my switch ports are engaged. Now, I have a printer connected to a wall point (RJ45) which I want to shift to a new room where there is no LAN setup. I want to have two RJ45 wall plugs in the new room so that I can connect one RJ45 port to have my LAN in the new room and the other RJ45 wall port I want to use for my printer. There is no option other than LAN (no wireless). Please help me and tell me how do I get the two RJ45 wall plate plugs in the new room up and keep my LAN running. It is a little urgent for me. Please help.

    Read the article

  • Multiple VLAN on one switch port

    - by Macropus
    I have a HP ProCurve 1810G-8 which I currently use as a normal switch between 3 servers and a firewall. 2 of the servers are ESXi hosts, and one is a Nexentastor box with 2 iSCSI target LUNs. As the iSCSI traffic is on the same LAN as all other traffic, I would like to switch this to use a SAN for iSCSI traffic and the LAN for all other traffic. The Nexentastor box only has 2 NICs, and as such, with a physical arrangement, I presume that one must be plugged into the SAN VLAN and one on the LAN VLAN ports of the switch. Is there a way to have multiple VLANs over the same port? e.g. the Nexentsator box has 2 NICs, both plugged into the switch, both ports with access to both of the VLANs?

    Read the article

  • Cisco Multi-DMZ firewall

    - by BParker
    I need to find a firewall that will give me 1 LAN port, and 5-7 DMZ ports. I have a requirement to replace some FreeBSD systems that are used to run some testing equipment. It is essential that the DMZ ports cannot communicate with each other, but the LAN port can communicate with everyone. That way a user on the LAN can connect to the test systems, but the test systems are isolated entirely and cannot interfere with each other. One of the DMZ's will be connected to a VMWare ESXi server, one to a standard server, and the rest to various types of equipment. The lan port will be connected to the corporate LAN switch. Sorry if i am a little vague, I am just trying to work all this out myself! Currently we have a FreeBSD configured, but the quad port NIC's are pretty expensive, and the PC itself is old, so i would prefer to replace it with a dedicate piece of kit which can do the same job, but more reliably! These test rigs are used all over the place, and get moved quite often, so i am aiming for Cisco kit for ease of configuration and reliability of the hardware itself. Thanks

    Read the article

  • Bug in CDP implementation

    - by Suraj
    We are developing a Linux based ethernet switch which has 6 ports. We are done with CDP protocol. I have connected a Cisco device to port 2. When I quiery for the Cisco device, I get the reply and instead of getting lan1 (port 1 - lan0 .. port 6 = lan5), I always get the interface name as eth0. The same is the case for all the ports. What changes are required to get the correct interface name? I will be very thankful for the information. The snap packet is received in the routine snap_rcv() in the file "linux._2.6.XX/net/802/psnap.c"; Regards, Suraj..

    Read the article

  • Trying to Set Up SSH Tunneling To MySQL Server for MySQL Query Browser

    - by Teno
    I'm trying to set up SSH tunneling on a remote web server to another MySQL server so that the database can be browsed easily with MySQL Query Browser. I'm following this page but cannot connect to the MySQL server. http://www.howtogeek.com/howto/ubuntu/access-your-mysql-server-remotely-over-ssh/ What I've done: logged in to the web server with Putty via SSH. typed ssh -L 33060:[database]:3306 [myusername]@[webserver_address] where [...]s are altered by the actual information. I was asked a password and typed it and got the following message. So it seems login was successful. socket: Protocol not supported Last login: .... 2012 from .... Copyright (c) 1980, 1983, 1986, 1988, 1990, 1991, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 7.1-RELEASE.... Welcome to FreeBSD! Opened MySQL Query Browser in Windows and entered Server Host: localhost Port: 33060 UserName: myusername PassWord: mypassword And it says, Could not connect to the specified instance. MySQL Error Number 2003 Can't connect to MySQL Server on 'localhost' (10061) Sorry if this is too basic. Thanks for your information.

    Read the article

  • DYNDNS setup with TightVNC on Windows Server 2008 R2

    - by StealthRT
    Hey all, i seem to be having a problem with getting ports to forward on my Windows Server 2008 R2 PC. I already set all my port forwarding for 5900/5800 on my router for my PC's IP address (192.168.1.22) but when i try to use the TightVNC PFPortChecker on port 5900 it tells me its not opened! I can not even connect to my DYNDNS server name (xxxxxxx.dyndns.org). As a side note, i am running Windows XP SP3 within a VirtaulBox inside Windows Server 2008 R2 but running the PFPortChecker in Windows 2008 R2 brings the same results as it does in the VM. I also added them to the Windows Firewall Advanced Security form to add those inbound ports for full access. What could i possibly be missing? Thanks for your time! David

    Read the article

  • Tomato QoS: Why is some traffic unclassified when there are classifications for it?

    - by Armitage
    Ok, I am trying to tweak my router to give priority to some traffic. My classifications seem to cover just about everything but I still see ~60 to ~80% of the traffic as unclassified: TCP 192.168.1.100 64137 192.168.1.1 80 Unclassified TCP 192.168.1.100 64175 192.168.1.1 80 Unclassified TCP 192.168.1.100 64144 192.168.1.1 443 Unclassified I assume that the 64### ports are just what my WAP uses to send packets inside my home network. But my classifications seems to cover any traffic for destination ports 80 and 443: (partial list) TCP Dst Port: 80,443 High WWW TCP/UDP Dst Port: 1024-65535 Lowest Bulk Traffic Why do I have so much unclassified traffic if I have a classification that should cover it?

    Read the article

  • Cannot see http (apache) server outside home network

    - by user165155
    Ive been racking my brain with this all evening. Power went out with a tstorm today, started back up my server... running apache and a team speak server on it. TS is great, cant see my web page outside my network! Firewall is disabled on the pc running it (centos btw), apache is running and working. correct ports are forwarded on my router (my isp blocks port 80). Ive tried changing ports, pretty much everything i can think of. httpd.conf is pointing to the correct addy and port, and my domain is pointing to the correct external ip. Im at a loss, any ideas out there?

    Read the article

  • USB 3.0 not functioning fully

    - by Simon Sheehan
    After installing GNU/Linux today onto my Lenovo Y570 laptop, I ran into an issue quickly - the USB 3.0 support. 2/3 of my USB ports are 3.0 so I kind of need them. The ports are powered at the very least - my phone is charging from one, however, plugging in external drives, USB drives, or even a mouse gives no response. The drives spin up, etc, but they do nothing more than that. So there is power, but no information flowing to them. What am I missing here? What can I try to enable to make things work?

    Read the article

  • HP ProCurve Port Mode Configuration Question Mark 2

    - by SvrGuy
    We have a ProCurve Switch 2810-48G (J9022A). We need to disable auto negotiation on two ports and manually configure them to be full duplex gige ports. From the web GUI, Configuration Tab, Port Configuration sub tab, I am only presented with the option to configure the port as Auto - 1000. I take this to mean, auto negotiate duplex, manually configure the speed to be gige. From the CLI when I try to set 1000-full I get the following error: Value 1000-full is not applicable to port 39 (or whatever port I try) The exact commands I have entered are: config interface 39 speed-duplex 1000-full BTW: speed-duplex auto-1000 works ( I also tried full-1000 and that did not work either) How do I manually configure the port such that it is manually configured to use full duplex, 1000 mbs?

    Read the article

  • Squid Proxy: url_regex acl is not working?

    - by bharathi
    I am using squid proxy 3.1 in ubuntu machine. I want to allow only urls matching our pattern through our proxy server. I configured acl like below. Acl for dstdomain is working fine. If i access any url besides .zmedia.com , I got proxy connection refused. But the url_regex is not working. What i am trying here is. Allow only request from ".zmedia.com" domain and the request url should be in "/blog" context. # # Recommended minimum configuration: # acl manager proto cache_object acl localhost src 127.0.0.1/32 ::1 acl to_localhost dst 127.0.0.0/8 ::1 acl urlwhitelist url_regex -i ^http(s)://([a-zA-Z]+).zmedia.com/blog/.*$ acl allowdomain dstdomain .zmedia.com acl Safe_ports port 80 8080 8500 7272 # Example rule allowing access from your local networks. # Adapt to list your (internal) IP networks from where browsing # should be allowed acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl SSL_ports port 7272 # multiling http acl CONNECT method CONNECT # # Recommended minimum Access Permission configuration: # # Only allow cachemgr access from localhost http_access allow manager localhost http_access deny manager http_access deny !allowdomain http_access allow urlwhitelist http_access allow CONNECT SSL_ports http_access deny CONNECT !SSL_ports # Deny requests to certain unsafe ports http_access deny !Safe_ports # Deny CONNECT to other than secure SSL ports http_access deny CONNECT !SSL_ports # We strongly recommend the following be uncommented to protect innocent # web applications running on the proxy server who think the only # one who can access services on "localhost" is a local user #http_access deny to_localhost # # INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS # # Example rule allowing access from your local networks. # Adapt localnet in the ACL section to list your (internal) IP networks # from where browsing should be allowed http_access allow localhost # And finally deny all other access to this proxy http_access deny all # Squid normally listens to port 3128 http_port 3128 # We recommend you to use at least the following line. hierarchy_stoplist cgi-bin ? # Uncomment and adjust the following to add a disk cache directory. #cache_dir ufs /var/spool/squid 100 16 256 # Leave coredumps in the first cache dir coredump_dir /var/spool/squid append_domain .zmedia.com # Add any of your own refresh_pattern entries above these. refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 Please correct me , If i did anything wrong?

    Read the article

  • Security question pertaining web application deployment

    - by orokusaki
    I am about to deploy a web application (in a couple months) with the following set-up (perhaps anyways): Ubuntu Lucid Lynx with: IP Tables firewall (white-list style with only 3 ports open) Custom SSH port (like 31847 or something) No "root" SSH access Long, random username (not just "admin" or something) with a long password (65 chars) PostgreSQL which only listens to localhost 256 bit SSL Cert Reverse proxy from NGINX to my application server (UWSGI) Assume that my colo is secure (Physical access isn't my concern for the time being) Application-level security (SQL injection, XSS, Directory Traversal, CSRF, etc) Perhaps IP masquerading (but I don't really understand this yet) Does this sound like a secure setup? I hear about people's web apps getting hacked all the time, and part of me thinks, "maybe they're just neglecting something", but the other part of me thinks, "maybe there's nothing you can do to protect your server, and those things are just measures to make it a little harder for script kiddies to get in". If I told you all of this, gave you my IP address, and told you what ports were available, would it be possible for you to get in (assuming you have a penetration testing tool), or is this really protected well.

    Read the article

  • Windows 7 USB power lose after a few seconds / minutes

    - by Stefan Dunn
    My friend's computer has a problem where the USB ports causes problems with the power of some devices connected to the computer. The USB mouse has no problems, however the Wireless Adapter looses power after around 20 seconds of use and USB Flash Drives cause the computer to either freeze, lose power (and become unresponsive) or become disconnected (still shown in Device Manager, but not in My Computer) when trying to transfer any type of file to / from the computer. I have a suspicion it's the Motherboard but could it also be a Software problem? Tried a new case, RAM, CPU and GFX Card which had no effect. The problem occurs on both the Front USB and Back (Motherboard) USB Ports. UPDATE: Tried the USB devices with an Ubuntu Live CD and they work fine, could this mean it's a problem with Windows (x64)?

    Read the article

  • iptables port forwarding troubleshooting

    - by cbmanica
    I'm trying to forward connections on port 18600 to port 9980. I have this in /etc/sysconfig/iptables: # Generated by iptables-save v1.3.5 on Mon Oct 21 18:30:43 2013 *nat :PREROUTING ACCEPT [2:280] :POSTROUTING ACCEPT [12:768] :OUTPUT ACCEPT [12:768] -A PREROUTING -p tcp -m tcp --dport 18600 -j REDIRECT --to-ports 9980 COMMIT # Completed on Mon Oct 21 18:30:43 2013 and /etc/init.d/iptables status shows me this: Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 REDIRECT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:18600 redir ports 9980 However, I can telnet from localhost to port 9980, but not 18600. What am I missing? (This is a CentOS-based VM.)

    Read the article

  • Connecting my XBOX 360 to home network

    - by patrick
    I am trying to set up my XBOX 360 as a Windows Media Center Extender. I input the code as shown on the XBOX screen, but I get the error message: "Cannot Set Up Extender." This means that the Extender was found (there's a separate error msg for extender not found), however it can't be set up. Windows points me to this page which tells me to change my router settings to enable multicast and UPnP. My router doesn't have those specific settings but I did open all ports for the XBOX. What is odd about this problem is that it did work, then I restarted my computer and didn't change any settings, and now it doesn't work. I guess something did change, but I can't figure out anything else to try after opening all ports. I'm running Windows 7 and the router is fairly recent (I bought it about six months ago) so it should be able to handle this. The router firmware is up to date.

    Read the article

  • vSphere ESX 5.5 hosts cannot connect to NFS Server

    - by Gerald
    Summary: My problem is I cannot use the QNAP NFS Server as an NFS datastore from my ESX hosts despite the hosts being able to ping it. I'm utilising a vDS with LACP uplinks for all my network traffic (including NFS) and a subnet for each vmkernel adapter. Setup: I'm evaluating vSphere and I've got two vSphere ESX 5.5 hosts (node1 and node2) and each one has 4x NICs. I've teamed them all up using LACP/802.3ad with my switch and then created a distributed switch between the two hosts with each host's LAG as the uplink. All my networking is going through the distributed switch, ideally, I want to take advantage of DRS and the redundancy. I have a domain controller VM ("Central") and vCenter VM ("vCenter") running on node1 (using node1's local datastore) with both hosts attached to the vCenter instance. Both hosts are in a vCenter datacenter and a cluster with HA and DRS currently disabled. I have a QNAP TS-669 Pro (Version 4.0.3) (TS-x69 series is on VMware Storage HCL) which I want to use as the NFS server for my NFS datastore, it has 2x NICs teamed together using 802.3ad with my switch. vmkernel.log: The error from the host's vmkernel.log is not very useful: NFS: 157: Command: (mount) Server: (10.1.2.100) IP: (10.1.2.100) Path: (/VM) Label (datastoreNAS) Options: (None) cpu9:67402)StorageApdHandler: 698: APD Handle 509bc29f-13556457 Created with lock[StorageApd0x411121] cpu10:67402)StorageApdHandler: 745: Freeing APD Handle [509bc29f-13556457] cpu10:67402)StorageApdHandler: 808: APD Handle freed! cpu10:67402)NFS: 168: NFS mount 10.1.2.100:/VM failed: Unable to connect to NFS server. Network Setup: Here is my distributed switch setup (JPG). Here are my networks. 10.1.1.0/24 VM Management (VLAN 11) 10.1.2.0/24 Storage Network (NFS, VLAN 12) 10.1.3.0/24 VM vMotion (VLAN 13) 10.1.4.0/24 VM Fault Tolerance (VLAN 14) 10.2.0.0/24 VM's Network (VLAN 20) vSphere addresses 10.1.1.1 node1 Management 10.1.1.2 node2 Management 10.1.2.1 node1 vmkernel (For NFS) 10.1.2.2 node2 vmkernel (For NFS) etc. Other addresses 10.1.2.100 QNAP TS-669 (NFS Server) 10.2.0.1 Domain Controller (VM on node1) 10.2.0.2 vCenter (VM on node1) I'm using a Cisco SRW2024P Layer-2 switch (Jumboframes enabled) with the following setup: LACP LAG1 for node1 (Ports 1 through 4) setup as VLAN trunk for VLANs 11-14,20 LACP LAG2 for my router (Ports 5 through 8) setup as VLAN trunk for VLANs 11-14,20 LACP LAG3 for node2 (Ports 9 through 12) setup as VLAN trunk for VLANs 11-14,20 LACP LAG4 for the QNAP (Ports 23 and 24) setup to accept untagged traffic into VLAN 12 Each subnet is routable to another, although, connections to the NFS server from vmk1 shouldn't need it. All other traffic (vSphere Web Client, RDP etc.) goes through this setup fine. I tested the QNAP NFS server beforehand using ESX host VMs atop of a VMware Workstation setup with a dedicated physical NIC and it had no problems. The ACL on the NFS Server share is permissive and allows all subnet ranges full access to the share. I can ping the QNAP from node1 vmk1, the adapter that should be used to NFS: ~ # vmkping -I vmk1 10.1.2.100 PING 10.1.2.100 (10.1.2.100): 56 data bytes 64 bytes from 10.1.2.100: icmp_seq=0 ttl=64 time=0.371 ms 64 bytes from 10.1.2.100: icmp_seq=1 ttl=64 time=0.161 ms 64 bytes from 10.1.2.100: icmp_seq=2 ttl=64 time=0.241 ms Netcat does not throw an error: ~ # nc -z 10.1.2.100 2049 Connection to 10.1.2.100 2049 port [tcp/nfs] succeeded! The routing table of node1: ~ # esxcfg-route -l VMkernel Routes: Network Netmask Gateway Interface 10.1.1.0 255.255.255.0 Local Subnet vmk0 10.1.2.0 255.255.255.0 Local Subnet vmk1 10.1.3.0 255.255.255.0 Local Subnet vmk2 10.1.4.0 255.255.255.0 Local Subnet vmk3 default 0.0.0.0 10.1.1.254 vmk0 VM Kernel NIC info ~ # esxcfg-vmknic -l Interface Port Group/DVPort IP Family IP Address Netmask Broadcast MAC Address MTU TSO MSS Enabled Type vmk0 133 IPv4 10.1.1.1 255.255.255.0 10.1.1.255 00:50:56:66:8e:5f 1500 65535 true STATIC vmk0 133 IPv6 fe80::250:56ff:fe66:8e5f 64 00:50:56:66:8e:5f 1500 65535 true STATIC, PREFERRED vmk1 164 IPv4 10.1.2.1 255.255.255.0 10.1.2.255 00:50:56:68:f5:1f 1500 65535 true STATIC vmk1 164 IPv6 fe80::250:56ff:fe68:f51f 64 00:50:56:68:f5:1f 1500 65535 true STATIC, PREFERRED vmk2 196 IPv4 10.1.3.1 255.255.255.0 10.1.3.255 00:50:56:66:18:95 1500 65535 true STATIC vmk2 196 IPv6 fe80::250:56ff:fe66:1895 64 00:50:56:66:18:95 1500 65535 true STATIC, PREFERRED vmk3 228 IPv4 10.1.4.1 255.255.255.0 10.1.4.255 00:50:56:72:e6:ca 1500 65535 true STATIC vmk3 228 IPv6 fe80::250:56ff:fe72:e6ca 64 00:50:56:72:e6:ca 1500 65535 true STATIC, PREFERRED Things I've tried/checked: I'm not using DNS names to connect to the NFS server. Checked MTU. Set to 9000 for vmk1, dvSwitch and Cisco switch and QNAP. Moved QNAP onto VLAN 11 (VM Management, vmk0) and gave it an appropriate address, still had same issue. Changed back afterwards of course. Tried initiating the connection of NAS datastore from vSphere Client (Connected to vCenter or directly to host), vSphere Web Client and the host's ESX Shell. All resulted in the same problem. Tried a path name of "VM", "/VM" and "/share/VM" despite not even having a connection to server. I plugged in a linux system (10.1.2.123) into a switch port configured for VLAN 12 and tried mounting the NFS share 10.1.2.100:/VM, it worked successfully and I had read-write access to it I tried disabling the firewall on the ESX host esxcli network firewall set --enabled false I'm out of ideas on what to try next. The things I'm doing differently from my VMware Workstation setup is the use of LACP with a physical switch and a virtual distributed switch between the two hosts. I'm guessing the vDS is probably the source of my troubles but I don't know how to fix this problem without eliminating it.

    Read the article

  • Preparing computers for remote MSI installation in NT4 domain

    - by user40177
    We recently purchased EMCO Remote Installer to deploy MSI packages we're creating. We are still (unfortunately) in an NT4 domain, and when I try to deploy a package using domain's administrator credentials I'm getting "access denied". Under the "requirements for remote computers" section on the EMCO website (http://www.emco.is/products/remote-installer/requirements.php), it says that it requires remote machines to have: * Started services: Computer Browser, Remote Registry * File and Printer sharing enabled * Windows Installer 3.1 * TCP ports opened: 135, 139, 445 * UDP ports opened: 137, 138 Is there any way of scripting these changes? If so, could someone get me started? I have about 200 machines I need to get this working with. Thanks for all your help!!

    Read the article

  • Two Routers - 1 Port Straight to First Router

    - by apples
    At my house we have two Wifi routers one's connected directly to the modem and the other is plugged in down stairs as a second network(Directly connected to the first router) Is there a way that I could make it so that I have the second router have its own network, but have one or two ports that would act as if they were directly connected to the first router? That way I can port forward to devices on the second router. Here are the information about the routers: Router 1 - Linksys WRT54G Running stock firmware Router 2 - Linksys E900 Running Tomato Firmware So to summarize what I'm asking is how would I have two networks from two routers but be able to connect directly to the first router through one of the ports on the second router. Here's a Visio Drawing of what I would like to look like

    Read the article

  • Using "enterprise" switches in home network?

    - by Industrial
    Hi everyone, After more than 12 years working with computers, I am still way behind when it comes to networking, so please bear with me :) As of this Christmas, the number of computers in my home has increased and it's well about time to upgrade the current network hardware in order to offer LAN connection to all computers. Trying to find a cheap solution, A close friend offered me a great deal on a "enterprise-class" Switch from HP (more LAN ports than I would ever need), at the same price as what a brand new Netgear or D-link Switch with 6/8 ports would cost me in retail. Would it be common sense to get this one and start using it immediately and never again have to worry about running out of LAN connections, or am I taking on a bigger bite than what I could chew?

    Read the article

< Previous Page | 36 37 38 39 40 41 42 43 44 45 46 47  | Next Page >