Search Results

Search found 10789 results on 432 pages for 'cpu upgrade'.

Page 404/432 | < Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >

• Windows for IoT, continued

  - by Valter Minute

  Originally posted on: http://geekswithblogs.net/WindowsEmbeddedCookbook/archive/2014/08/05/windows-for-iot-continued.aspxI received many interesting feedbacks on my previous blog post and I tried to find some time to do some additional tests. Bert Kleinschmidt pointed out that pins 2,3 and 10 of the Galileo are connected directly to the SOC, while pin 13, the one used for the sample sketch is controlled via an I2C I/O expander. I changed my code to use pin 2 instead of 13 (just changing the variable assignment at the beginning of the code) and latency was greatly reduced. Now each pulse lasts for 1.44ms, 44% more than the expected time, but ways better that the result we got using pin 13. I also used SetThreadPriority to increase the priority of the thread that was running the sketch to THREAD_PRIORITY_HIGHEST but that didn't change the results. When I was using the I2C-controlled pin I tried the same and the timings got ways worse (increasing more than 10 times) and so I did not commented on that part, wanting to investigate the issua a bit more in detail. It seems that increasing the priority of the application thread impacts negatively the I2C communication. I tried to use also the Linux-based implementation (using a different Galileo board since the one provided by MS seems to use a different firmware) and the results of running the sample blink sketch modified to use pin 2 and blink the led for 1ms are similar to those we got on the same board running Windows. Here the difference between expected time and measured time is worse, getting around 3.2ms instead of 1 (320% compared to 150% using Windows but far from the 100.1% we got with the 8-bit Arduino). Both systems were not under load during the test, maybe loading some applications that use part of the CPU time would make those timings even less reliable, but I think that those numbers are enough to draw some conclusions. It may not be worth running a full OS if what you need is Arduino compatibility. The Arduino UNO is probably the best Arduino you can find to perform this kind of development. The Galileo running the Linux-based stack or running Windows for IoT is targeted to be a platform for "Internet of Things" devices, whatever that means. At the moment I don't see the "I" part of IoT. We have low level interfaces (SPI, I2C, the GPIO pins) that can be used to connect sensors but the support for connectivity is limited and the amount of work required to deliver some data to the cloud (using a secure HTTP request or a message queuing system like APMQS or MQTT) is still big and the rich OS underneath seems to not provide any help doing that.Why should I use sockets and can't access all the high level connectivity features we have on "full" Windows?I know that it's possible to use some third party libraries, try to build them using the Windows For IoT SDK etc. but this means re-inventing the wheel every time and can also lead to some IP concerns if used for products meant to be closed-source. I hope that MS and Intel (and others) will focus less on the "coolness" of running (some) Arduino sketches and more on providing a better platform to people that really want to design devices that leverage internet connectivity and the cloud processing power to deliver better products and services. Providing a reliable set of connectivity services would be a great start. Providing support for .NET would be even better, leaving native code available for hardware access etc. I know that those components may require additional storage and memory etc. So making the OS componentizable (or, at least, provide a way to install additional components) would be a great way to let developers pick the parts of the system they need to develop their solution, knowing that they will integrate well together. I can understand that the Arduino and Raspberry Pi* success may have attracted the attention of marketing departments worldwide and almost any new development board those days is promoted as "XXX response to Arduino" or "YYYY alternative to Raspberry Pi", but this is misleading and prevents companies from focusing on how to deliver good products and how to integrate "IoT" features with their existing offer to provide, at the end, a better product or service to their customers. Marketing is important, but can't decide the key features of a product (the OS) that is going to be used to develop full products for end customers integrating it with hardware and application software. I really like the "hackable" nature of open-source devices and like to see that companies are getting more and more open in releasing information, providing "hackable" devices and supporting developers with documentation, good samples etc. On the other side being able to run a sketch designed for an 8 bit microcontroller on a full-featured application processor may sound cool and an easy upgrade path for people that just experimented with sensors etc. on Arduino but it's not, in my humble opinion, the main path to follow for people who want to deliver real products.   *Shameless self-promotion: if you are looking for a good book in Italian about the Raspberry Pi , try mine: http://www.amazon.it/Raspberry-Pi-alluso-Digital-LifeStyle-ebook/dp/B00GYY3OKO

  Read the article

• UppercuT v1.0 and 1.1&ndash;Linux (Mono), Multi-targeting, SemVer, Nitriq and Obfuscation, oh my!

  - by Robz / Fervent Coder

  Recently UppercuT (UC) quietly released version 1 (in August). I’m pretty happy with where we are, although I think it’s a few months later than I originally planned. I’m glad I held it back, it gave me some more time to think about some things a little more and also the opportunity to receive a patch for running builds with UC on Linux. We also released v1.1 very recently (December). UppercuT v1 Builds On Linux Perhaps the most significant changes to UC going v1 is that it now supports builds on Linux using Mono! This is thanks mostly to Svein Ackenhausen for the patches and working with me on getting it all working while not breaking the windows builds!  This means you can use mono on Windows or Linux. Notice the shell files to execute with Linux that come as part of UC now. Multi-Targeting Perhaps one of the hardest things to do that requires an automated build is multi-targeting. At v1 this is early, and possibly prone to some issues, but available.  We believe in making everything stupid simple, so it’s as simple as adding a comma to the microsoft.framework property. i.e. “net-3.5, net-4.0” to suddenly produce both framework builds. When you build, this is what you get (if you meet each framework’s requirements): At this time you have to let UC override the build location (as it does by default) or this will not work.  Semantic Versioning By now many of you have been using UppercuT for awhile and have watched how we have done versioning. Many of you who use git already know we put the revision hash in the informational/product version as the last octet. At v1, UppercuT has adopted the semantic versioning scheme. What does that mean? This is a short read, but a good one: http://SemVer.org SemVer (Semantic Versioning) is really using versioning what it was meant for. You have three octets. Major.Minor.Patch as in 1.1.0.  UC will use three different versioning concepts, one for the assembly version, one for the file version, and one for the product version. All versions - The first three octects of the version are owned by SemVer. Major.Minor.Patch i.e.: 1.1.0 Assembly Version - The assembly version would much closer follow SemVer. Last digit is always 0. Major.Minor.Patch.0 i.e: 1.1.0.0 File Version - The file version occupies the build number as the last digit. Major.Minor.Patch.Build i.e.: 1.1.0.2650 Product/Informational Version - The last octect of your product/informational version is the source control revision/hash. Major.Minor.Patch.RevisionOrHash i.e. (TFS/SVN): 1.1.0.235 i.e. (Git/HG): 1.1.0.a45ace4346adef0 SemVer is not on by default, the passive versioning scheme is still in effect. Notice that version.use_semanticversioning has been added to the UppercuT.config file (and version.patch in support of the third octet): Gems Support Gems support was added at v1. This will probably be deprecated as some point once there is an announced sunset for Nu v1. Application gems may keep it around since there is no alternative for that yet though (CoApp would be a possible replacement). Nitriq Support Nitriq is a code analysis tool like NDepend. It’s built by Mr. Jon von Gillern. It uses LINQ query language, so you can use a familiar idiom when analyzing your code base. It’s a pretty awesome tool that has a free version for those looking to do code analysis! To use Nitriq with UC, you are going to need the console edition.  To take advantage of Nitriq, you just need to update the location of Nitriq in the config: Then add the nitriq project files at the root of your source. Please refer to the Nitriq documentation on how these are created. UppercuT v1.1 Obfuscation One thing I started looking into was an easy way to obfuscate my code. I came across EazFuscator, which is both free and awesome. Plus the GUI for it is super simple to use. How do you make obfuscation even easier? Make it a convention and a configurable property in the UC config file! And the code gets obfuscated! Closing Definitely get out and look at the new release. It contains lots of chocolaty (sp?) goodness. And remember, the upgrade path is almost as simple as drag and drop!

  Read the article

• #OOW 2012 @PARIS...talking Oracle and Clouds, and Optimized Datacenter

  - by Eric Bezille

  For those of you who want to get most out of Oracle technologies to evolve your IT to the Next Wave, I encourage you to register to the up coming Oracle Optimized Datacenter event that will take place in Paris on November 28th. You will get the opportunity to exchange with Oracle experts and customers having successfully evolve their IT by leveraging Oracle technologies. You will also get the latest news on some of the Oracle systems announcements made during OOW 2012. During this event we will make an update about Oracle and Clouds, from private to public and hybrid models. So in preparing this session, I thought it was a good start to make a status of Cloud Computing in France, and CIO requirements in particular. Starting in 2009 with the first Cloud Camp in Paris, the market has evolved, but the basics are still the same : think hybrid. From Traditional IT to Clouds One size doesn't fit all, and for big companies having already an IT in place, there will be parts eligible to external (public) cloud, and parts that would be required to stay inside the firewalls, so ability to integrate both side is key.  None the less, one of the major impact of Cloud Computing trend on IT, reported by Forrester, is the pressure it makes on CIO to evolve towards the same model that end-users are now used to in their day to day life, where self-service and flexibility are paramount. This is what is driving IT to transform itself toward "a Global Service Provider", or for some as "IT "is" the Business" (see : Gartner Identifies Four Futures for IT and CIO), and for both models toward a Private Cloud Service Provider. In this journey, there is still a big difference between most of existing external Cloud and a firm IT : the number of applications that a CIO has to manage. Most cloud providers today are overly specialized, but at the end of the day, there are really few business processes that rely on only one application. So CIOs has to combine everything together external and internal. And for the internal parts that they will have to make them evolve to a Private Cloud, the scope can be very large. This will often require CIOs to evolve from their traditional approach to more disruptive ones, the time has come to introduce new standards and processes, if they want to succeed. So let's have a look at the different Cloud models, what type of users they are addressing, what value they bring and most importantly what needs to be done by the  Cloud Provider, and what is left over to the user. IaaS, PaaS, SaaS : what's provided and what needs to be done First of all the Cloud Provider will have to provide all the infrastructure needed to deliver the service. And the more value IT will want to provide, the more IT will have to deliver and integrate : from disks to applications. As we can see in the above picture, providing pure IaaS, left a lot to cover for the end-user, that’s why the end-user targeted by this Cloud Service is IT people. If you want to bring more value to developers, you need to provide to them a development platform ready to use, which is what PaaS is standing for, by providing not only the processors power, storage and OS, but also the Database and Middleware platform. SaaS being the last mile of the Cloud, providing an application ready to use by business users, the remaining part for the end-users being configuring and specifying the application for their specific usage. In addition to that, there are common challenges encompassing all type of Cloud Services : Security : covering all aspect, not only of users management but also data flows and data privacy Charge back : measuring what is used and by whom Application management : providing capabilities not only to deploy, but also to upgrade, from OS for IaaS, Database, and Middleware for PaaS, to a full Business Application for SaaS. Scalability : ability to evolve ALL the components of the Cloud Provider stack as needed Availability : ability to cover “always on” requirements Efficiency : providing a infrastructure that leverage shared resources in an efficient way and still comply to SLA (performances, availability, scalability, and ability to evolve) Automation : providing the orchestration of ALL the components in all service life-cycle (deployment, growth & shrink (elasticity), upgrades,...) Management : providing monitoring, configuring and self-service up to the end-users Oracle Strategy and Clouds For CIOs to succeed in their Private Cloud implementation, means that they encompass all those aspects for each component life-cycle that they selected to build their Cloud. That’s where a multi-vendors layered approach comes short in terms of efficiency. That’s the reason why Oracle focus on taking care of all those aspects directly at Engineering level, to truly provide efficient Cloud Services solutions for IaaS, PaaS and SaaS. We are going as far as embedding software functions in hardware (storage, processor level,...) to ensure the best SLA with the highest efficiency. The beauty of it, as we rely on standards, is that the Oracle components that you are running today in-house, are exactly the same that we are using to build Clouds, bringing you flexibility, reversibility and fast path to adoption. With Oracle Engineered Systems (Exadata, Exalogic & SPARC SuperCluster, more specifically, when talking about Cloud), we are delivering all those components hardware and software already engineered together at Oracle factory, with a single pane of glace for the management of ALL the components through Oracle Enterprise Manager, and with high-availability, scalability and ability to evolve by design. To give you a feeling of what does that bring in terms just of implementation project timeline, for example with Oracle SPARC SuperCluster, we have a consistent track of record to have the system plug into existing Datacenter and ready in a week. This includes Oracle Database, OS, virtualization, Database Storage (Exadata Storage Cells in this case), Application Storage, and all network configuration. This strategy enable CIOs to very quickly build Cloud Services, taking out not only the complexity of integrating everything together but also taking out the automation and evolution complexity and cost. I invite you to discuss all those aspect in regards of your particular context face2face on November 28th.

  Read the article

• A Basic Thread

  - by Joe Mayo

  Most of the programs written are single-threaded, meaning that they run on the main execution thread. For various reasons such as performance, scalability, and/or responsiveness additional threads can be useful. .NET has extensive threading support, from the basic threads introduced in v1.0 to the Task Parallel Library (TPL) introduced in v4.0. To get started with threads, it's helpful to begin with the basics; starting a Thread. Why Do I Care? The scenario I'll use for needing to use a thread is writing to a file.  Sometimes, writing to a file takes a while and you don't want your user interface to lock up until the file write is done. In other words, you want the application to be responsive to the user. How Would I Go About It? The solution is to launch a new thread that performs the file write, allowing the main thread to return to the user right away.  Whenever the file writing thread completes, it will let the user know.  In the meantime, the user is free to interact with the program for other tasks. The following examples demonstrate how to do this. Show Me the Code? The code we'll use to work with threads is in the System.Threading namespace, so you'll need the following using directive at the top of the file: using System.Threading; When you run code on a thread, the code is specified via a method.  Here's the code that will execute on the thread: private static void WriteFile() { Thread.Sleep(1000); Console.WriteLine("File Written."); } The call to Thread.Sleep(1000) delays thread execution. The parameter is specified in milliseconds, and 1000 means that this will cause the program to sleep for approximately 1 second.  This method happens to be static, but that's just part of this example, which you'll see is launched from the static Main method.  A thread could be instance or static.  Notice that the method does not have parameters and does not have a return type. As you know, the way to refer to a method is via a delegate.  There is a delegate named ThreadStart in System.Threading that refers to a method without parameters or return type, shown below: ThreadStart fileWriterHandlerDelegate = new ThreadStart(WriteFile); I'll show you the whole program below, but the ThreadStart instance above goes in the Main method. The thread uses the ThreadStart instance, fileWriterHandlerDelegate, to specify the method to execute on the thread: Thread fileWriter = new Thread(fileWriterHandlerDelegate); As shown above, the argument type for the Thread constructor is the ThreadStart delegate type. The fileWriterHandlerDelegate argument is an instance of the ThreadStart delegate type. This creates an instance of a thread and what code will execute, but the new thread instance, fileWriter, isn't running yet. You have to explicitly start it, like this: fileWriter.Start(); Now, the code in the WriteFile method is executing on a separate thread. Meanwhile, the main thread that started the fileWriter thread continues on it's own.  You have two threads running at the same time. Okay, I'm Starting to Get Glassy Eyed. How Does it All Fit Together? The example below is the whole program, pulling all the previous bits together. It's followed by its output and an explanation. using System; using System.Threading; namespace BasicThread { class Program { static void Main() { ThreadStart fileWriterHandlerDelegate = new ThreadStart(WriteFile); Thread fileWriter = new Thread(fileWriterHandlerDelegate); Console.WriteLine("Starting FileWriter"); fileWriter.Start(); Console.WriteLine("Called FileWriter"); Console.ReadKey(); } private static void WriteFile() { Thread.Sleep(1000); Console.WriteLine("File Written"); } } } And here's the output: Starting FileWriter Called FileWriter File Written So, Why are the Printouts Backwards? The output above corresponds to Console.Writeline statements in the program, with the second and third seemingly reversed. In a single-threaded program, "File Written" would print before "Called FileWriter". However, this is a multi-threaded (2 or more threads) program.  In multi-threading, you can't make any assumptions about when a given thread will run.  In this case, I added the Sleep statement to the WriteFile method to greatly increase the chances that the message from the main thread will print first. Without the Thread.Sleep, you could run this on a system with multiple cores and/or multiple processors and potentially get different results each time. Interesting Tangent but What Should I Get Out of All This? Going back to the main point, launching the WriteFile method on a separate thread made the program more responsive.  The file writing logic ran for a while, but the main thread returned to the user, as demonstrated by the print out of "Called FileWriter".  When the file write finished, it let the user know via another print statement. This was a very efficient use of CPU resources that made for a more pleasant user experience. Joe

  Read the article

• Upgrading to Code Based Migrations EF 4.3.1 with Connector/Net 6.6

  - by GABMARTINEZ

  Entity Framework 4.3.1 includes a new feature called code first migrations.  We are adding support for this feature in our upcoming 6.6 release of Connector/Net.  In this walk-through we'll see the workflow of code-based migrations when you have an existing application and you would like to upgrade to this EF 4.3.1 version and use this approach, so you can keep track of the changes that you do to your database.   The first thing we need to do is add the new Entity Framework 4.3.1 package to our application. This should via the NuGet package manager.  You can read more about why EF is not part of the .NET framework here. Adding EF 4.3.1 to our existing application  Inside VS 2010 go to Tools -> Library Package Manager -> Package Manager Console, this will open the Power Shell Host Window where we can work with all the EF commands. In order to install this library to your existing application you should type Install-Package EntityFramework This will make some changes to your application. So Let's check them. In your .config file you'll see a  <configSections> which contains the version you have from EntityFramework and also was added the <entityFramework> section as shown below. This section is by default configured to use SQL Express which won't be necesary for this case. So you can comment it out or leave it empty. Also please make sure you're using the Connector/Net 6.6.x version which is the one that has this support as is shown in the previous image. At this point we face one issue; in order to be able to work with Migrations we need the __MigrationHistory table that we don't have yet since our Database was created with an older version. This table is used to keep track of the changes in our model. So we need to get it in our existing Database. Getting a Migration-History table into an existing database First thing we need to do to enable migrations in our existing application is to create our configuration class which will set up the MySqlClient Provider as our SQL Generator. So we have to add it with the following code: using System.Data.Entity.Migrations;     //add this at the top of your cs file public class Configuration : DbMigrationsConfiguration<NameOfYourDbContext>  //Make sure to use the name of your existing DBContext { public Configuration() { this.AutomaticMigrationsEnabled = false; //Set Automatic migrations to false since we'll be applying the migrations manually for this case. SetSqlGenerator("MySql.Data.MySqlClient", new MySql.Data.Entity.MySqlMigrationSqlGenerator());     }   }  This code will set up our configuration that we'll be using when executing all the migrations for our application. Once we have done this we can Build our application so we can check that everything is fine. Creating our Initial Migration Now let's add our Initial Migration. In Package Manager Console, execute "add-migration InitialCreate", you can use any other name but I like to set this as our initial create for future reference. After we run this command, some changes were done in our application: A new Migrations Folder was created. A new class migration call InitialCreate which in most of the cases should have empty Up and Down methods as long as your database is up to date with your Model. Since all your entities already exists, delete all duplicated code to create any entity which exists already in your Database if there is any. I found this easier when you don't have any pending updates to do to your database. Now we have our empty migration that will make no changes in our database and represents how are all the things at the begining of our migrations.  Finally, let's create our MigrationsHistory table. Optionally you can add SQL code to delete the edmdata table which is not needed anymore. public override void Up() { // Just make sure that you used 4.1 or later version         Sql("DROP TABLE EdmMetadata"); } From our Package Manager Console let's type: Update-database; If you like to see the operations made on each Update-database command you can use the flag -verbose after the Update-database. This will make two important changes.  It will execute the Up method in the initial migration which has no changes in the database. And second, and very important,  it will create the __MigrationHistory table necessary to keep track of your changes. And next time you make a change to your database it will compare the current model to the one stored in the Model Column of this table. Conclusion The important thing of this walk through is that we must create our initial migration before we start doing any changes to our model. This way we'll be adding the necessary __MigrationsHistory table to our existing database, so we can keep our database up to date with all the changes we do in our context model using migrations. Hope you have found this information useful. Please let us know if you have any questions or comments, also please check our forums here where we keep answering questions in general for the community.  Happy MySQL/Net Coding!

  Read the article

• Top Questions and Answers for Pluging into Oracle Database as a Service

  - by David Swanger

  Yesterday we hosted a comprehensive online forum that shared a comprehensive path to help your organization design, deploy, and deliver a Database as a Service cloud. If you missed the online forum, you can watch it on demand by registering here. We received numerous questions.  Below are highlights of the most informative: DBaaS requires a lengthy and careful design efforts. What is the minimum requirements of setting up a scaled-down environment and test it out? You should have an OEM 12c environment for DBaaS administration and then a target database deployment platform that has the key characteristics of what your production environment will look like. This could be a single server or it could be a small pool of hosts if your production DBaaS will be larger and you want to test a more robust / real world configuration with Zones and Pools or DR capabilities for example. How does this benefit companies having their own data center? This allows companies to transform their internal IT to a service delivery model for the database. The benefits to the company are significant cost savings, improved business agility and reduced risk. The benefits to the consumers (internal) of services if much fast provisioning, and response to change in business requirements. From a deployment perspective, is DBaaS's job solely DBA's job? The best deployment model enables the DBA (or end-user) to control the entire process. All resources required to deploy the service are pre-provisioned, and there are no external dependencies (on network, storage, sysadmins teams). The service is created either via a self-service portal or by the DBA. The purpose of self service seems to be that the end user does not rely on the DBA. I just need to give him a template. He decides how much AMM he needs. Why shall I set it one by one. That doesn't seem to be the purpose of self service. Most customers we have worked with define a standardized service catalog, with a few (2 to 5) different classes of service. For each of these classes, there is a pre-defined deployment template, and the user has the ability to select from some pre-defined service sizes. The administrator only has to create this catalog once. Each user then simply selects from the options offered in the catalog.  Looking at DBaaS service definition, it seems to be no different from a service definition provided by a well defined DBA team. Why do you attribute it to DBaaS? There are a couple of perspectives. First, some organizations might already be operating with a high level of standardization and a higher level of maturity from an ITIL or Service Management perspective. Their journey to DBaaS could be shorter and their Service Definition will evolve less but they still might need to add capabilities such as Self Service and Metering/Chargeback. Other organizations are still operating in highly siloed environments with little automation and their formal Service Definition (if they have one) will be a lot less mature today. Therefore their future state DBaaS will look a lot different from their current state, as will their Service Definition. How database as a service impact or help with "Click to Compute" or deploying "Database in cloud infrastructure" DBaaS enables Click to Compute. Oracle DBaaS can be implemented using three architecture models: Oracle Multitenant 12c, native consolidation using Oracle Database and consolidation using virtualization in infrastructure cloud. As Deploy session showed, you get higher consolidating density and efficiency using Multitenant and higher isolation using infrastructure cloud. Depending upon your business needs, DBaaS can be implemented using any of these models. How exactly is the DBaaS different from the traditional db? Storage/OS/DB all together to 'transparently' provide service to applications? Will there be across-databases access by application/user. Some key differences are: 1) The services run on a shared platform. 2) The services can be rapidly provisioned (< 15 minutes). 3) The services are dynamic and can be relocated, grown, shrunk as needed to meet business needs without disruption and rapidly. 4) The user is able to provision the services directly from a standardized service catalog.. With 24x7x365 databases its difficult to find off peak hrs to do basic admin tasks such as gathering stats, running backups, batch jobs. How does pluggable database handle this and different needs/patching downtime of apps databases might be serving? You can gather stats in Oracle Multitenant the same way you had been in regular databases. Regarding patching/upgrading, Oracle Multitenant makes patch/upgrade very efficient in that you can pre-provision a new version/patched multitenant db in a different ORACLE_HOME and then unplug a PDB from its CDB and plug it into the newer/patched CDB in seconds.  Thanks for all the great questions!  If you'd like to learn more and missed the online forum, you can watch it on demand here.

  Read the article

• SQLIO Writes

  - by Grant Fritchey

  SQLIO is a fantastic utility for testing the abilities of the disks in your system. It has a very unfortunate name though, since it's not really a SQL Server testing utility at all. It really is a disk utility. They ought to call it DiskIO because they'd get more people using I think. Anyway, branding is not the point of this blog post. Writes are the point of this blog post. SQLIO works by slamming your disk. It performs as mean reads as it can or it performs as many writes as it can depending on how you've configured your tests. There are much smarter people than me who will get into all the various types of tests you should run. I'd suggest reading a bit of what Jonathan Kehayias (blog|twitter) has to say or wade into Denny Cherry's (blog|twitter) work. They're going to do a better job than I can describing all the benefits and mechanisms around using this excellent piece of software. My concerns are very focused. I needed to set up a series of tests to see how well our product SQL Storage Compress worked. I wanted to know the effects it would have on a system, the disk for sure, but also memory and CPU. How to stress the system? SQLIO of course. But when I set it up and ran it, following the documentation that comes with it, I was seeing better than 99% compression on the files. Don't get me wrong. Our product is magnificent, wonderful, all things great and beautiful, gets you coffee in the morning and is made mostly from bacon. But 99% compression. No, it's not that good. So what's up? Well, it's the configuration. The default mechanism is to load up a file, something large that will overwhelm your disk cache. You're instructed to load the file with a character 0x0. I never got a computer science degree. I went to film school. Because of this, I didn't memorize ASCII tables so when I saw this, I thought it was zero's or something. Nope. It's NULL. That's right, you're making a very large file, but you're filling it with NULL values. That's actually ok when all you're testing is the disk sub-system. But, when you want to test a compression and decompression, that can be an issue. I got around this fairly quickly. Instead of generating a file filled with NULL values, I just copied a database file for my tests. And to test it with SQL Storage Compress, I used a database file that had already been run through compression (about 40% compression on that file if you're interested). Now the reads were taken care of. I am seeing very realistic performance from decompressing the information for reads through SQLIO. But what about writes? Well, the issue is, what does SQLIO write? I don't have access to the code. But I do have access to the results. I did two different tests, just to be sure of what I was seeing. First test, use the .DAT file as described in the documentation. I opened the .DAT file after I was done with SQLIO, using WordPad. Guess what? It's a giant file full of air. SQLIO writes NULL values. What does that do to compression? I did the test again on a copy of an uncompressed database file. Then I ran the original and the SQLIO modified copy through ZIP to see what happened. I got better than 99% compression out of the SQLIO modified file (original file of 624,896kb went to 275,871kb compressed, after SQLIO it went to 608kb compressed). So, what does SQLIO write? It writes air. If you're trying to test it with compression or maybe some other type of file storage mechanism like dedupe, you need to know this because your tests really won't be valid. Should I find some other mechanism for testing? Yeah, if all I'm interested in is establishing performance to my own satisfaction, yes. But, I want to be able to compare my results with other people's results and we all need to be using the same tool in order for that to happen. SQLIO is the common mechanism that most people I know use to establish disk performance behavior. It'd be better if we could get SQLIO to do writes in some other fashion. Oh, and before I go, I get to brag a bit. Measuring IOPS, SQL Storage Compress outperforms my disk alone by about 30%.

  Read the article

• Hiring New IT Employees versus Promoting Internally for IT Positions

  Recently I was asked my opinion regarding the hiring of IT professionals in regards to the option of hiring new IT employees versus promoting internally for IT positions. After thinking a little more about this question regarding staffing, specifically pertaining to promoting internally verses new employees; I think my answer to this question is that it truly depends on the situation. However, in most cases I would side with promoting internally. The key factors in this decision should be based on a company/department’s current values, culture, attitude, and existing priorities.  For example if a company values retaining all of its hard earned business knowledge then they would tend to promote existing employees internal over hiring a new employee. Moreover, the company will have to pay to train an existing employee to learn a new technology and the learning curve for some technologies can be very steep. Conversely, if a company values new technologies and technical proficiency over business knowledge then a company would tend to hire new employees because they may already have experience with a technology that the company is planning on using. In this scenario, the company would have to take on the additional overhead of allowing a new employee to learn how the business operates prior to them being fully effective. To illustrate my points above let us look at contractor that builds in ground pools for example.  He has the option to hire employees that are very strong but use small shovels to dig, or employees weak in physical strength but use large shovels to dig. Which employee should the contractor use to dig a hole for a new in ground pool? If we compare the possible candidates for this job we will find that they are very similar to hiring someone internally verses a new hire. The first example represents the existing workers that are very strong regarding the understanding how the business operates and the reasons why in a specific manner. However this employee could be potentially weaker than an outsider pertaining to specific technologies and would need some time to build their technical prowess for a new position much like the strong worker upgrading their shovels in order to remove more dirt at once when digging. The other employee is very similar to hiring a new person that may already have the large shovel but will need to increase their strength in order to use the shovel properly and efficiently so that they can move a maximum amount of dirt in a minimal amount of time. This can be compared to new employ learning how a business operates before they can be fully functional and integrated in the company/department. Another key factor in this dilemma pertains to existing employee and their passion for their work, their ability to accept new responsibility when given, and the willingness to take on responsibilities when they see a need in the business. As much as possible should be considered in this decision down to the mood of the team, the quality of existing staff, learning cure for both technology and business, and the potential side effects of the existing staff.  In addition, there are many more consideration based on the current team/department/companies culture and mood. There are several factors that need to be considered when promoting an individual or hiring new blood for a team. They both can provide great benefits as well as create controversy to a group. Personally, staffing especially in the IT world is like building a large scale system in that all of the components and modules must fit together and preform as one cohesive system in the same way a team must come together using their individually acquired skills so that they can work as one team.  If a module is out of place or is nonexistent then the rest of the team will suffer until the all of its issues are addressed and resolved. Benefits of Promoting Internally Internal promotions give employees a reason to constantly upgrade their technology, business, and communication skills if they want to further their career Employees can control their own destiny based on personal desires Employee already knows how the business operates Companies can save money by promoting internally because the initial overhead of allowing new hires to learn how a company operates is very expensive Newly promoted employees can assist in training their replacements while transitioning to their new role within a company. Existing employees already have a proven track record in regards fitting in with the business culture; this is always an unknown with all new hires Benefits of a New Hire New employees can energize and excite existing employees New employees can bring new ideas and advancements in technology New employees can offer a different perspective on existing issues based on their past experience. As you can see the decision to promote an existing employee from within a company verses hiring a new person should be based on several factors that should ultimately place the business in the best possible situation for the immediate and long term future. How would you handle this situation? Would you hire a new employee or promote from within?

  Read the article

• My Feelings About Microsoft Surface

  - by Valter Minute

  Advice: read the title carefully, I’m talking about “feelings” and not about advanced technical points proved in a scientific and objective way I still haven’t had a chance to play with a MS Surface tablet (I would love to, of course) and so my ideas just came from reading different articles on the net and MS official statements. Remember also that the MVP motto begins with “Independent” (“Independent Experts. Real World Answers.”) and this is just my humble opinion about a product and a technology. I know that, being an MS MVP you can be called an “MS-fanboy”, I don’t care, I hope that people can appreciate my opinion, even if it doesn’t match theirs. The “Surface” brand can be confusing for techies that knew the “original” surface concept but I think that will be a fresh new brand name for most of the people out there. But marketing department are here to confuse people… so I can understand this “recycle” of an existing name. So Microsoft is entering the hardware arena… for me this is good news. Microsoft developed some nice hardware in the past: the xbox, zune (even if the commercial success was quite limited) and, last but not least, the two arc mices (old and new model) that I use and appreciate. In the past Microsoft worked with OEMs and that model lead to good and bad things. Good thing (for microsoft, at least) is market domination by windows-based PCs that only in the last years has been reduced by the return of the Mac and tablets. Google is also moving in the hardware business with its acquisition of Motorola, and Apple leveraged his control of both the hardware and software sides to develop innovative products. Microsoft can scare OEMs and make them fly away from windows (but where?) or just lead the pack, showing how devices should be designed to compete in the market and bring back some of the innovation that disappeared from recent PC products (look at the shelves of your favorite electronics store and try to distinguish a laptop between the huge mass of anonymous PCs on displays… only Macs shine out there…). Having to compete with MS “official” hardware will force OEMs to develop better product and bring back some real competition in a market that was ruled only by prices (the lower the better even when that means low quality) and no innovative features at all (when it was the last time that a new PC surprised you?). Moving into a new market is a big and risky move, but with Windows 8 Microsoft is playing a crucial move for its future, trying to be back in the innovation run against apple and google. MS can’t afford to fail this time. I saw the new devices (the WinRT and Pro) and the specifications are scarce, misleading and confusing. The first impression is that the device looks like an iPad with a nice keyboard cover… Using “HD” and “full HD” to define display resolution instead of using the real figures and reviving the “ClearType” brand (now dead on Win8 as reported here and missed by people who hate to read text on displays, like myself) without providing clear figures (couldn’t you count those damned pixels?) seems to imply that MS was caught by surprise by apple recent “retina” displays that brought very high definition screens on tablets.Also there are no specifications about the processors used (even if some sources report NVidia Tegra for the ARM tablet and i5 for the x86 one) and expected battery life (a critical point for tablets and the point that killed Windows7 x86 based tablets). Also nothing about the price, and this will be another critical point because other platform out there already provide lots of applications and have a good user base, if MS want to enter this market tablets pricing must be competitive. There are some expansion ports (SD and USB), so no fixed storage model (even if the specs talks about 32-64GB for RT and 128-256GB for pro). I like this and don’t like the apple model where flash memory (that it’s dirt cheap used in thumdrives or SD cards) is as expensive as gold (or cocaine to have a more accurate per gram measurement) when mounted inside a tablet/phone. For big files you’ll be able to use external media and an SD card could be used to store files that don’t require super-fast SSD-like access times, I hope. To be honest I really don’t like the marketplace model and the limitation of Windows RT APIs (no local database? from a company that based a good share of its success on VB6+Access!) and lack of desktop support on the ARM (even if the support is here and has been used to port office). It’s a step toward the consumer market (where competitors are making big money), but may impact enterprise (and embedded) users that may not appreciate Windows 8 new UI or the limitations of the new app model (if you aren’t connected you are dead ). Not having compatibility with the desktop will require brand new applications and honestly made all the CPU cycles spent to convert .NET IL into real machine code in the past like a huge waste of time… as soon as a new processor architecture is supported by Windows you still have to rewrite part of your application (and MS is pushing HTML5+JS and native code more than .NET in my perception). On the other side I believe that the development experience provided by Visual Studio is still miles (or kilometres) ahead of the competition and even the all-uppercase menu of VS2012 hasn’t changed this situation. The new metro UI got mixed reviews. On my side I should say that is very pleasant to use on a touch screen, I like the minimalist design (even if sometimes is too minimal and hides stuff that, in my opinion, should be visible) but I should also say that using it with mouse and keyboard is like trying to pick your nose with boxing gloves… Metro is also very interesting for embedded devices where touch screen usage is quite common and where having an application taking all the screen is the norm. For devices like kiosks, vending machines etc. this kind of UI can be a great selling point. I don’t need a new tablet (to be honest I’m pretty happy with my wife’s iPad and with my PC), but I may change my opinion after having a chance to play a little bit with those new devices and understand what’s hidden under all this mysterious and generic announcements and specifications!

  Read the article

• WEBLOGIC 12C HANDS-ON BOOTCAMP

  - by agallego

    Oracle PartnerNetwork | Account | Feedback   JOIN THE ORACLE WEBLOGIC PARTNER COMMUNITY AND ATTEND A WEBLOGIC 12C HANDS-ON BOOTCAMP Dear partner As a valued partner we would like to invite you for the WebLogic Partner Community and our WebLogic 12c hands-on Bootcamps – free of charge! Please first login at http://partner.oracle.com and then visit: WebLogic Partner Community. (If you need support with your account please contact the Oracle Partner Business Center). The goal of the WebLogic Partner Community is to provide you with the latest information on Oracle's offerings and to facilitate the exchange of experience within community members. Register Now FREE Assessment vouchers to become certified and WebLogic Server 12c 200 new Features and Training Connect and Network   WebLogic Blogs   WebLogic on Facebook   WebLogic on LinkedIn   WebLogic on Twitter   WebLogic on Oracle Mix WebLogic 12c hands-on Workshops We offer free3 days hands-on WebLogic 12c workshops for Oracle partners who want to become Application Grid Specialized: Register Here! Country Date Location Registration   Germany  3-5 April 2012 Oracle Düsseldorf Click here   France  24-26 April 2012 Oracle Colombes Click here   Spain 08-10 May 2012  Oracle Madrid  Click here   Netherlands  22-24 May 2012  Oracle Amsterdam  Click here   United Kingdom  06-08 June 2012  Oracle Reading  Click here   Italy  19-21 June 2012  Oracle Cinisello Balsamo  Click here   Portugal  10-12 July 2012  Oracle Lisbon  Click here Skill requirements Attendees need to have the following skills as this is required by the product-set and to make sure they get the most out of the training: Basic knowledge in Java and JavaEE Understanding the Application Server concept Basic knowledge in older releases of WebLogic Server would be beneficial Member of WebLogic Partner Community for registration please vist http://www.oracle.com/partners/goto/wls-emea Hardware requirements Every participant works on his own notebook. The minimal hardware requirements are: 4Gb physical RAM (we will boot the image with 2Gb RAM)  dual core CPU 15 GB HD Software requirements Please install Oracle VM VirtualBox 4.1.8 Follow-up and certification  With the workshop registration you agree to the following next steps Follow-up training attend and pass the Oracle Application Grid Certified Implementation Specialist Registration For details and registration please visit Register Here Free WebLogic Certification (Free assessment voucher to become certified) For all WebLogic experts, we offer free vouchers worth $195 for the Oracle Application Grid Certified Implementation Specialist assessment. To demonstrate your WebLogic knowledge you first have to pass the free online assessment Oracle Application Grid PreSales Specialist. For free vouchers, please send an e-mail with the screenshot of your Oracle Application Grid PreSales certirficate to [email protected] including your Name, Company, E-mail and Country. Note: This offer is limited to partners from Europe Middle East and Africa. Partners from other countries please contact your Oracle partner manager. WebLogic Specialization To become specialized in Application Grid, please make sure that you access the: Application Grid Specialization Guide Application Grid Specialization Checklist If you have any questions please contact the Oracle Partner Business Center. Oracle WebLogic Server 12c Key New Capabilities Java EE 6 and Developer Productivity Simplified Deployment and Management with Virtualization Integrated Traffic Management Enhanced High Availability and Disaster Recovery Much Higher Performance For more information please visit: Presentation from the WebLogic 12c launch Technical Presentation from the WebLogic 12c launch WebLogic OTN Website WebLogic 12c Virtual Conference Environment WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea (OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Best regards, Jürgen Kress WebLogic Partner Adoption EMEA Tel. +49 89 1430 1479 E-Mail: [email protected]   Copyright © 2012, Oracle and/or its affiliates. All rights reserved. Contact PBC | Legal Notices and Terms of Use | Privacy Statement Oracle Corporation - Worldwide Headquarters, 500 Oracle Parkway, OPL - E-mail Services, Redwood Shores, CA 94065, United States Your privacy is important to us. You can login to your account to update your e-mail subscriptions or you can opt-out of all Oracle Marketing e-mails at any time. Please note that opting-out of Marketing communications does not affect your receipt of important business communications related to your current relationship with Oracle such as Security Updates, Event Registration notices, Account Management and Support/Service communications.

  Read the article

• Understanding the 'High Performance' meaning in Extreme Transaction Processing

  - by kyap

  Despite my previous blogs entries on SOA/BPM and Identity Management, the domain where I'm the most passionated is definitely the Extreme Transaction Processing, commonly called XTP.I came across XTP back to 2007 while I was still FMW Product Manager in EMEA. At that time Oracle acquired a company called Tangosol, which owned an unique product called Coherence that we renamed to Oracle Coherence. Beside this innovative renaming of the product, to be honest, I didn't know much about it, except being a "distributed in-memory cache for Extreme Transaction Processing"... not very helpful still.In general when people doesn't fully understand a technology or a concept, they tend to find some shortcuts, either correct or not, to justify their lack-of understanding... and of course I was part of this category of individuals. And the shortcut was "Oracle Coherence Cache helps to improve Performance". Excellent marketing slogan... but not very meaningful still. By chance I was able to get away quickly from that group in July 2007* at Thames Valley Park (UK), after I attended one of the most interesting workshops, in my 10 years career in Oracle, delivered by Brian Oliver. The biggest mistake I made was to assume that performance improvement with Coherence was related to the response time. Which can be considered as legitimus at that time, because after-all caches help to reduce latency on cached data access, hence reduce the response-time. But like all caches, you need to define caching and expiration policies, thinking about the cache-missed strategy, and most of the time you have to re-write partially your application in order to work with the cache. At a result, the expected benefit vanishes... so, not very useful then?The key mistake I made was my perception or obsession on how performance improvement should be driven, but I strongly believe this is still a common problem to most of the developers. In fact we all know the that the performance of a system is generally presented by the Capacity (or Throughput), with the 2 important dimensions Speed (response-time) and Volume (load) :Capacity (TPS) = Volume (T) / Speed (S)To increase the Capacity, we can either reduce the Speed(in terms of response-time), or to increase the Volume. However we tend to only focus on reducing the Speed dimension, perhaps it is more concrete and tangible to measure, and nicer to present to our management because there's a direct impact onto the end-users experience. On the other hand, we assume the Volume can be addressed by the underlying hardware or software stack, so if we need more capacity (scale out), we just add more hardware or software. Unfortunately, the reality proves that IT is never as ideal as we assume...The challenge with Speed improvement approach is that it is generally difficult and costly to make things already fast... faster. And by adding Coherence will not necessarily help either. Even though we manage to do so, the Capacity can not increase forever because... the Speed can be influenced by the Volume. For all system, we always have a performance illustration as follow: In all traditional system, the increase of Volume (Transaction) will also increase the Speed (Response-Time) as some point. The reason is simple: most of the time the Application logics were not designed to scale. As an example, if you have a while-loop in your application, it is natural to conceive that parsing 200 entries will require double execution-time compared to 100 entries. If you need to "Speed-up" the execution, you can only upgrade your hardware (scale-up) with faster CPU and/or network to reduce network latency. It is technically limited and economically inefficient. And this is exactly where XTP and Coherence kick in. The primary objective of XTP is about designing applications which can scale-out for increasing the Volume, by applying coding techniques to keep the execution-time as constant as possible, independently of the number of runtime data being manipulated. It is actually not just about having an application running as fast as possible, but about having a much more predictable system, with constant response-time and linearly scale, so we can easily increase throughput by adding more hardwares in parallel. It is in general combined with the Low Latency Programming model, where we tried to optimize the network usage as much as possible, either from the programmatic angle (less network-hoops to complete a task), and/or from a hardware angle (faster network equipments). In this picture, Oracle Coherence can be considered as software-level XTP enabler, via the Distributed-Cache because it can guarantee: - Constant Data Objects access time, independently from the number of Objects and the Coherence Cluster size - Data Objects Distribution by Affinity for in-memory data grouping - In-place Data Processing for parallel executionTo summarize, Oracle Coherence is indeed useful to improve your application performance, just not in the way we commonly think. It's not about the Speed itself, but about the overall Capacity with Extreme Load while keeping consistant Speed. In the future I will keep adding new blog entries around this topic, with some sample codes experiences sharing that I capture in the last few years. In the meanwhile if you want to know more how Oracle Coherence, I strongly suggest you to start with checking how our worldwide customers are using Oracle Coherence first, then you can start playing with the product through our tutorial.Have Fun !

  Read the article

• Documentation Changes in Solaris 11.1

  - by alanc

  One of the first places you can see Solaris 11.1 changes are in the docs, which have now been posted in the Solaris 11.1 Library on docs.oracle.com. I spent a good deal of time reviewing documentation for this release, and thought some would be interesting to blog about, but didn't review all the changes (not by a long shot), and am not going to cover all the changes here, so there's plenty left for you to discover on your own. Just comparing the Solaris 11.1 Library list of docs against the Solaris 11 list will show a lot of reorganization and refactoring of the doc set, especially in the system administration guides. Hopefully the new break down will make it easier to get straight to the sections you need when a task is at hand. Packaging System Unfortunately, the excellent in-depth guide for how to build packages for the new Image Packaging System (IPS) in Solaris 11 wasn't done in time to make the initial Solaris 11 doc set. An interim version was published shortly after release, in PDF form on the OTN IPS page. For Solaris 11.1 it was included in the doc set, as Packaging and Delivering Software With the Image Packaging System in Oracle Solaris 11.1, so should be easier to find, and easier to share links to specific pages the HTML version. Beyond just how to build a package, it includes details on how Solaris is packaged, and how package updates work, which may be useful to all system administrators who deal with Solaris 11 upgrades & installations. The Adding and Updating Oracle Solaris 11.1 Software Packages was also extended, including new sections on Relaxing Version Constraints Specified by Incorporations and Locking Packages to a Specified Version that may be of interest to those who want to keep the Solaris 11 versions of certain packages when they upgrade, such as the couple of packages that had functionality removed by an (unusual for an update release) End of Feature process in the 11.1 release. Also added in this release is a document containing the lists of all the packages in each of the major package groups in Solaris 11.1 (solaris-desktop, solaris-large-server, and solaris-small-server). While you can simply get the contents of those groups from the package repository, either via the web interface or the pkg command line, the documentation puts them in handy tables for easier side-by-side comparison, or viewing the lists before you've installed the system to pick which one you want to initially install. X Window System We've not had good X11 coverage in the online Solaris docs in a while, mostly relying on the man pages, and upstream X.Org docs. In this release, we've integrated some X coverage into the Solaris 11.1 Desktop Adminstrator's Guide, including sections on installing fonts for fontconfig or legacy X11 clients, X server configuration, and setting up remote access via X11 or VNC. Of course we continue to work on improving the docs, including a lot of contributions to the upstream docs all OS'es share (more about that another time). Security One of the things Oracle likes to do for its products is to publish security guides for administrators & developers to know how to build systems that meet their security needs. For Solaris, we started this with Solaris 11, providing a guide for sysadmins to find where the security relevant configuration options were documented. The Solaris 11.1 Security Guidelines extend this to cover new security features, such as Address Space Layout Randomization (ASLR) and Read-Only Zones, as well as adding additional guidelines for existing features, such as how to limit the size of tmpfs filesystems, to avoid users driving the system into swap thrashing situations. For developers, the corresponding document is the Developer's Guide to Oracle Solaris 11 Security, which has been the source for years for documentation of security-relevant Solaris API's such as PAM, GSS-API, and the Solaris Cryptographic Framework. For Solaris 11.1, a new appendix was added to start providing Secure Coding Guidelines for Developers, leveraging the CERT Secure Coding Standards and OWASP guidelines to provide the base recommendations for common programming languages and their standard API's. Solaris specific secure programming guidance was added via links to other documentation in the product doc set. In parallel, we updated the Solaris C Libary Functions security considerations list with details of Solaris 11 enhancements such as FD_CLOEXEC flags, additional *at() functions, and new stdio functions such as asprintf() and getline(). A number of code examples throughout the Solaris 11.1 doc set were updated to follow these recommendations, changing unbounded strcpy() calls to strlcpy(), sprintf() to snprintf(), etc. so that developers following our examples start out with safer code. The Writing Device Drivers guide even had the appendix updated to list which of these utility functions, like snprintf() and strlcpy(), are now available via the Kernel DDI. Little Things Of course all the big new features got documented, and some major efforts were put into refactoring and renovation, but there were also a lot of smaller things that got fixed as well in the nearly a year between the Solaris 11 and 11.1 doc releases - again too many to list here, but a random sampling of the ones I know about & found interesting or useful: The Privileges section of the DTrace Guide now gives users a pointer to find out how to set up DTrace privileges for non-global zones and what limitations are in place there. A new section on Recommended iSCSI Configuration Practices was added to the iSCSI configuration section when it moved into the SAN Configuration and Multipathing administration guide. The Managing System Power Services section contains an expanded explanation of the various tunables for power management in Solaris 11.1. The sample dcmd sources in /usr/demo/mdb were updated to include ::help output, so that developers like myself who follow the examples don't forget to include it (until a helpful code reviewer pointed it out while reviewing the mdb module changes for Xorg 1.12). The README file in that directory was updated to show the correct paths for installing both kernel & userspace modules, including the 64-bit variants.

  Read the article

• Content in Context: The right medicine for your business applications

  - by Lance Shaw

  For many of you, your companies have already invested in a number of applications that are critical to the way your business is run. HR, Payroll, Legal, Accounts Payable, and while they might need an upgrade in some cases, they are all there and handling the lifeblood of your business. But are they really running as efficiently as they could be? For many companies, the answer is no. The problem has to do with the important information caught up within documents and paper. It’s everywhere except where it truly needs to be – readily available right within the context of the application itself. When the right information cannot be easily found, business processes suffer significantly. The importance of this recently struck me when I recently went to meet my new doctor and get a routine physical. Walking into the office lobby, I couldn't help but notice rows and rows of manila folders in racks from floor to ceiling, filled with documents and sensitive, personal information about various patients like myself.  As I looked at all that paper and all that history, two things immediately popped into my head.  “How do they find anything?” and then the even more alarming, “So much for information security!” It sure looked to me like all those documents could be accessed by anyone with a key to the building. Now the truth is that the offices of many general practitioners look like this all over the United States and the world.  But it had me thinking, is the same thing going on in just about any company around the world, involving a wide variety of important business processes? Probably so. Think about all the various processes going on in your company right now. Invoice payments are being processed through Accounts Payable, contracts are being reviewed by Procurement, and Human Resources is reviewing job candidate submissions and doing background checks. All of these processes and many more like them rely on access to forms and documents, whether they are paper or digital. Now consider that it is estimated that employee’s spend nearly 9 hours a week searching for information and not finding it. That is a lot of very well paid employees, spending more than one day per week not doing their regular job while they search for or re-create what already exists. Back in the doctor’s office, I saw this trend exemplified as well. First, I had to fill out a new patient form, even though my previous doctor had transferred my records over months previously. After filling out the form, I was later introduced to my new doctor who then interviewed me and asked me the exact same questions that I had answered on the form. I understand that there is value in the interview process and it was great to meet my new doctor, but this simple process could have been so much more efficient if the information already on file could have been brought directly together with the new patient information I had provided. Instead of having a highly paid medical professional re-enter the same information into the records database, the form I filled out could have been immediately scanned into the system, associated with my previous information, discrepancies identified, and the entire process streamlined significantly. We won’t solve the health records management issues that exist in the United States in this blog post, but this example illustrates how the automation of information capture and classification can eliminate a lot of repetitive and costly human entry and re-creation, even in a simple process like new patient on-boarding. In a similar fashion, by taking a fresh look at the various processes in place today in your organization, you can likely spot points along the way where automating the capture and access to the right information could be significantly improved. As you evaluate how content-process flows through your organization, take a look at how departments and regions share information between the applications they are using. Business applications are often implemented on an individual department basis to solve specific problems but a holistic approach to overall information management is not taken at the same time. The end result over the years is disparate applications with separate information repositories and in many cases these contain duplicate information, or worse, slightly different versions of the same information. This is where Oracle WebCenter Content comes into the story. More and more companies are realizing that they can significantly improve their existing application processes by automating the capture of paper, forms and other content. This makes the right information immediately accessible in the context of the business process and making the same information accessible across departmental systems which has helped many organizations realize significant cost savings. Here on the Oracle WebCenter team, one of our primary goals is to help customers find new ways to be more effective, more cost-efficient and manage information as effectively as possible. We have a series of three webcasts occurring over the next few weeks that are focused on the integration of enterprise content management within the context of business applications. We hope you will join us for one or all three and that you will find them informative. Click here to learn more about these sessions and to register for them. There are many aspects of information management to consider as you look at integrating content management within your business applications. We've barely scratched the surface here but look for upcoming blog posts where we will discuss more specifics on the value of delivering documents, forms and images directly within applications like Oracle E-Business Suite, PeopleSoft Enterprise, JD Edwards Enterprise One, Siebel CRM and many others. What do you think?  Are your important business processes as healthy as they can be?  Do you have any insights to share on the value of delivering content directly within critical business processes? Please post a comment and let us know the value you have realized, the lessons learned and what specific areas you are interested in.

  Read the article

• Joining on NULLs

  - by Dave Ballantyne

  A problem I see on a fairly regular basis is that of dealing with NULL values.  Specifically here, where we are joining two tables on two columns, one of which is ‘optional’ ie is nullable.  So something like this: i.e. Lookup where all the columns are equal, even when NULL.   NULL’s are a tricky thing to initially wrap your mind around.  Statements like “NULL is not equal to NULL and neither is it not not equal to NULL, it’s NULL” can cause a serious brain freeze and leave you a gibbering wreck and needing your mummy. Before we plod on, time to setup some data to demo against. Create table #SourceTable ( Id integer not null, SubId integer null, AnotherCol char(255) not null ) go create unique clustered index idxSourceTable on #SourceTable(id,subID) go with cteNums as ( select top(1000) number from master..spt_values where type ='P' ) insert into #SourceTable select Num1.number,nullif(Num2.number,0),'SomeJunk' from cteNums num1 cross join cteNums num2 go Create table #LookupTable ( Id integer not null, SubID integer null ) go insert into #LookupTable Select top(100) id,subid from #SourceTable where subid is not null order by newid() go insert into #LookupTable Select top(3) id,subid from #SourceTable where subid is null order by newid() If that has run correctly, you will have 1 million rows in #SourceTable and 103 rows in #LookupTable.  We now want to join one to the other. First attempt – Lets just join select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and #LookupTable.SubID = #SourceTable.SubID OK, that’s a fail.  We had 100 rows back,  we didn’t correctly account for the 3 rows that have null values.  Remember NULL <> NULL and the join clause specifies SUBID=SUBID, which for those rows is not true. Second attempt – Lets deal with those pesky NULLS select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and isnull(#LookupTable.SubID,0) = isnull(#SourceTable.SubID,0) OK, that’s the right result, well done and 99.9% of the time that is where its left. It is a relatively trivial CPU overhead to wrap ISNULL around both columns and compare that result, so no problems.  But, although that’s true, this a relational database we are using here, not a procedural language.  SQL is a declarative language, we are making a request to the engine to get the results we want.  How we ask for them can make a ton of difference. Lets look at the plan for our second attempt, specifically the clustered index seek on the #SourceTable   There are 2 predicates. The ‘seek predicate’ and ‘predicate’.  The ‘seek predicate’ describes how SQLServer has been able to use an Index.  Here, it has been able to navigate the index to resolve where ID=ID.  So far so good, but what about the ‘predicate’ (aka residual probe) ? This is a row-by-row operation.  For each row found in the index matching the Seek Predicate, the leaf level nodes have been scanned and tested using this logical condition.  In this example [Expr1007] is the result of the IsNull operation on #LookupTable and that is tested for equality with the IsNull operation on #SourceTable.  This residual probe is quite a high overhead, if we can express our statement slightly differently to take full advantage of the index and make the test part of the ‘Seek Predicate’. Third attempt – X is null and Y is null So, lets state the query in a slightly manner: select * from #SourceTable join #LookupTable on #LookupTable.id = #SourceTable.id and ( #LookupTable.SubID = #SourceTable.SubID or (#LookupTable.SubID is null and #SourceTable.SubId is null) ) So its slightly wordier and may not be as clear in its intent to the human reader, that is what comments are for, but the key point is that it is now clearer to the query optimizer what our intention is. Let look at the plan for that query, again specifically the index seek operation on #SourceTable No ‘predicate’, just a ‘Seek Predicate’ against the index to resolve both ID and SubID.  A subtle difference that can be easily overlooked.  But has it made a difference to the performance ? Well, yes , a perhaps surprisingly high one. Clever query optimizer well done. If you are using a scalar function on a column, you a pretty much guaranteeing that a residual probe will be used.  By re-wording the query you may well be able to avoid this and use the index completely to resolve lookups. In-terms of performance and scalability your system will be in a much better position if you can.

  Read the article

• Tech Talk: Managing Cloud Integration

  - by Tanu Sood

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Cloud computing solutions are widely hailed as a way to reduce capital expenditures yet organizations are realizing they need to also consider all of the nuances of integrating cloud applications with existing information systems.Cloud integration, after all, has a direct impact on your costs, maintenance and upgrade efforts. Catch this conversation on Tech Talk with Oracle Vice President, Amit Zavery, to understand how Oracle Fusion Middleware provides a simple and consistent method to maintaining integration interfaces across disparate systems across cloud and on-premise applications. Simplify your IT infrastructure and seamlessly manage data and application integration across your applications with Oracle solutions. Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} For other Fusion Middleware talks, subscribe to Fusion Middleware Radio today and visit us on oracle.com Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Photo courtesy: www.cloudtweaks.com

  Read the article

• Increasing efficiency of N-Body gravity simulation

  - by Postman

  I'm making a space exploration type game, it will have many planets and other objects that will all have realistic gravity. I currently have a system in place that works, but if the number of planets goes above 70, the FPS decreases an practically exponential rates. I'm making it in C# and XNA. My guess is that I should be able to do gravity calculations between 100 objects without this kind of strain, so clearly my method is not as efficient as it should be. I have two files, Gravity.cs and EntityEngine.cs. Gravity manages JUST the gravity calculations, EntityEngine creates an instance of Gravity and runs it, along with other entity related methods. EntityEngine.cs public void Update() { foreach (KeyValuePair<string, Entity> e in Entities) { e.Value.Update(); } gravity.Update(); } (Only relevant piece of code from EntityEngine, self explanatory. When an instance of Gravity is made in entityEngine, it passes itself (this) into it, so that gravity can have access to entityEngine.Entities (a dictionary of all planet objects)) Gravity.cs namespace ExplorationEngine { public class Gravity { private EntityEngine entityEngine; private Vector2 Force; private Vector2 VecForce; private float distance; private float mult; public Gravity(EntityEngine e) { entityEngine = e; } public void Update() { //First loop foreach (KeyValuePair<string, Entity> e in entityEngine.Entities) { //Reset the force vector Force = new Vector2(); //Second loop foreach (KeyValuePair<string, Entity> e2 in entityEngine.Entities) { //Make sure the second value is not the current value from the first loop if (e2.Value != e.Value ) { //Find the distance between the two objects. Because Fg = G * ((M1 * M2) / r^2), using Vector2.Distance() and then squaring it //is pointless and inefficient because distance uses a sqrt, squaring the result simple cancels that sqrt. distance = Vector2.DistanceSquared(e2.Value.Position, e.Value.Position); //This makes sure that two planets do not attract eachother if they are touching, completely unnecessary when I add collision, //For now it just makes it so that the planets are not glitchy, performance is not significantly improved by removing this IF if (Math.Sqrt(distance) > (e.Value.Texture.Width / 2 + e2.Value.Texture.Width / 2)) { //Calculate the magnitude of Fg (I'm using my own gravitational constant (G) for the sake of time (I know it's 1 at the moment, but I've been changing it) mult = 1.0f * ((e.Value.Mass * e2.Value.Mass) / distance); //Calculate the direction of the force, simply subtracting the positions and normalizing works, this fixes diagonal vectors //from having a larger value, and basically makes VecForce a direction. VecForce = e2.Value.Position - e.Value.Position; VecForce.Normalize(); //Add the vector for each planet in the second loop to a force var. Force = Vector2.Add(Force, VecForce * mult); //I have tried Force += VecForce * mult, and have not noticed much of an increase in speed. } } } //Add that force to the first loop's planet's position (later on I'll instead add to acceleration, to account for inertia) e.Value.Position += Force; } } } } I have used various tips (about gravity optimizing, not threading) from THIS question (that I made yesterday). I've made this gravity method (Gravity.Update) as efficient as I know how to make it. This O(N^2) algorithm still seems to be eating up all of my CPU power though. Here is a LINK (google drive, go to File download, keep .Exe with the content folder, you will need XNA Framework 4.0 Redist. if you don't already have it) to the current version of my game. Left click makes a planet, right click removes the last planet. Mouse moves the camera, scroll wheel zooms in and out. Watch the FPS and Planet Count to see what I mean about performance issues past 70 planets. (ALL 70 planets must be moving, I've had 100 stationary planets and only 5 or so moving ones while still having 300 fps, the issue arises when 70+ are moving around) After 70 planets are made, performance tanks exponentially. With < 70 planets, I get 330 fps (I have it capped at 300). At 90 planets, the FPS is about 2, more than that and it sticks around at 0 FPS. Strangely enough, when all planets are stationary, the FPS climbs back up to around 300, but as soon as something moves, it goes right back down to what it was, I have no systems in place to make this happen, it just does. I considered multithreading, but that previous question I asked taught me a thing or two, and I see now that that's not a viable option. I've also thought maybe I could do the calculations on my GPU instead, though I don't think it should be necessary. I also do not know how to do this, it is not a simple concept and I want to avoid it unless someone knows a really noob friendly simple way to do it that will work for an n-body gravity calculation. (I have an NVidia gtx 660) Lastly I've considered using a quadtree type system. (Barnes Hut simulation) I've been told (in the previous question) that this is a good method that is commonly used, and it seems logical and straightforward, however the implementation is way over my head and I haven't found a good tutorial for C# yet that explains it in a way I can understand, or uses code I can eventually figure out. So my question is this: How can I make my gravity method more efficient, allowing me to use more than 100 objects (I can render 1000 planets with constant 300+ FPS without gravity calculations), and if I can't do much to improve performance (including some kind of quadtree system), could I use my GPU to do the calculations?

  Read the article

• 2012&ndash;The End Of The World Review

  - by Tim Murphy

  The end of the world must be coming.  Not because the Mayan calendar says so, but because Microsoft is innovating more than Apple.  It has been a crazy year, with pundits declaring not that the end of the world is coming, but that the end of Microsoft is coming.  Let’s take a look at what 2012 has brought us. The beginning of year is a blur.  I managed to get to TechEd in June which was the first time that I got to take a deep dive into Windows 8 and many other things that had been announced in 2011.  The promise I saw in these products was really encouraging.  The thought of being able to run Windows 8 from a thumb drive or have Hyper-V native to the OS told me that at least for developers good things were coming. I finally got my feet wet with Windows 8 with the developer preview just prior to the RTM.  While the initial experience was a bit of a culture shock I quickly grew to love it.  The media still seems to hold little love for the “reimagined” platform, but I think that once people spend some time with it they will enjoy the experience and what the FUD mongers say will fade into the background.  With the launch of the OS we finally got a look at the Surface.  I think this is a bold entry into the tablet market.  While I wish it was a little more affordable I am already starting to see them in the wild being used by non-techies. I was waiting for Windows Phone 8 at least as much as Windows 8, probably more.  The new hardware, better marketing and new OS features I think are going to finally push us to the point of having a real presence in the smartphone market.  I am seeing a number of iPhone users picking up a Nokia Lumia 920 and getting rid of their brand new iPhone 5.  The only real debacle that I saw around the launch was when they held back the SDK from general developers. Shortly after the launch events came Build 2012.  I was extremely disappointed that I didn’t make it to this year’s Build.  Even if they weren’t handing out Surface and Lumia devices I think the atmosphere and content were something that really needed to be experience in person.  Hopefully there will be a Build next year and it’s schedule will be announced soon.  As you would expect Windows 8 and Windows Phone 8 development were the mainstay of the conference, but improvements in Azure also played a key role.  This movement of services to the cloud will continue and we need to understand where it best fits into the solutions we build. Lower on the radar this year were Office 2013, SQL Server 2012, and Windows Server 2012.  Their glory stolen by the consumer OS and hardware announcements, these new releases are no less important.  Companies will see significant improvements in performance and capabilities if they upgrade.  At TechEd they had shown some of the new features of Windows Server 2012 around hardware integration and Hyper-V performance which absolutely blew me away.  It is our job to bring these important improvements to our company’s attention so that they can be leveraged. Personally, the consulting business in 2012 was the busiest it has been in a long time.  More companies were ready to attack new projects after several years of putting them on the back burner.  I also worked to bring back momentum to the Chicago Information Technology Architects Group.  Both the community and clients are excited about the new technologies that have come out in 2012 and now it is time to deliver. What does 2013 have in store.  I don’t see it be quite as exciting as 2012.  Microsoft will be releasing the Surface Pro in January and it seems that we will see more frequent OS update for Windows.  There are rumors that we may see a Surface phone in 2013.  It has also been announced that there will finally be a rework of the XBox next fall.  The new year will also be a time for us in the development community to take advantage of these new tools and devices.  After all, it is what we build on top of these platforms that will attract more consumers and corporations to using them. Just as I am 99.999% sure that the world is not going to end this year, I am also sure that Microsoft will move on and that most of this negative backlash from the media is actually fear and jealousy.  In the end I think we have a promising year ahead of us. del.icio.us Tags: Microsoft,Pundits,Mayans,Windows 8,Windows Phone 8,Surface

  Read the article

• What's New in Oracle VM VirtualBox 4.2?

  - by Fat Bloke

  A year is a long time in the IT industry. Since the last VirtualBox feature release, which was a little over a year ago, we've seen: new releases of cool new operating systems, such as Windows 8, ChromeOS, and Mountain Lion; we've seen a myriad of new Linux releases from big Enterprise class distributions like Oracle 6.3, to accessible desktop distros like Ubuntu 12.04 and Fedora 17; and we've also seen the spec of a typical PC or laptop double in power. All of these events have influenced our new VirtualBox version which we're releasing today. Here's how... Powerful hosts  One of the trends we've seen is that as the average host platform becomes more powerful, our users are consistently running more and more vm's. Some of our users have large libraries of vm's of various vintages, whilst others have groups of vm's that are run together as an assembly of the various tiers in a multi-tiered software solution, for example, a database tier, middleware tier, and front-ends.  So we're pleased to unveil a more powerful VirtualBox Manager to address the needs of these users: VM Groups Groups allow you to organize your VM library in a sensible way, e.g.  by platform type, by project, by version, by whatever. To create groups you can drag one VM onto another or select one or more VM's and choose Machine...Group from the menu bar. You can expand and collapse groups to save screen real estate, and you can Enter and Leave a group (think iPad navigation here) by using the right and left arrow keys when groups are selected. But groups are more than passive folders, because you can now also perform operations on groups, rather than all the individual VMs. So if you have a multi-tiered solution you can start the whole stack up with just one click. Autostart Many VirtualBox users run dedicated services in their VMs, for example, running a Wiki. With these types of VM workloads, you really want the VM start up when the host machine boots up. So with 4.2 we've introduced a cross-platform Auto-start mechanism to allow you to treat VMs as host services. Headless VM Launching With VM's such as web servers, wikis, and other types of server-class workloads, the Console of the VM is pretty much redundant. For some time now VirtualBox has offered a separate launch mechanism for these VM's, namely the command-line interface commands VBoxHeadless or VBoxManage startvm ... --type headless commands. But with 4.2 we also allow you launch headless VMs from the Manager. Simply hold down Shift when launching the VM from the Manager.  It's that easy. But how do you stop a headless VM? Well, with 4.2 we allow you to Close the VM from the Manager. (BTW best to use the ACPI Shutdown method which allows the guest VM to close down gracefully.) Easy VM Creation For our expert users, the  New VM Wizard was a little tiresome, so now there's a faster 2-click VM creation mode. Just Hide the description when creating a new VM. Powerful VMs  As the hosts have become more powerful, so are the guests that are running inside them. Here are some of the 4.2 features to accommodate them: Virtual Network Interface Cards  With 4.2, it's now possible to create VMs with up to 36 NICs, when using the ICH9 chipset emulation. But with great power comes great responsibility (didn't Obi-Wan say something similar?), and so we have also introduced bandwidth limiting to prevent a rogue VM stealing the whole pipe. VLAN tagging Some of our users leverage VLANs extensively so we've enhanced the E1000 NICs to support this.  Processor Performance If you are running a CPU which supports Nested Paging (aka EPT in the Intel world) such as most of the Core i5 and i7 CPUs, or are running an AMD Bulldozer or later, you should see some performance improvements from our work with these processors. And while we're talking Processors, we've added support for some of the more modern VIA CPUs too. Powerful Automation Because VirtualBox runs atop a fully blown operating system, it makes sense to leverage the capabilities of the host to run scripts that can drive the guest VMs. Guest Automation was introduced in a prior release but with 4.2 we've revamped the APIs to allow a richer and more powerful set of operations to be executed by the guest. Check out the IGuest APIs in the VirtualBox Programming Guide and Reference (SDK). Powerful Platforms  All the hardcore engineering that has gone into 4.2 has been done for a purpose and that is to deliver a fast and powerful engine that can run almost any x86 OS because of the integrity of the virtualization. So we're pleased to add support for these platforms: Mac OS X "Mountain Lion"  Windows 8 Windows Server 2012 Ubuntu 12.04 (“Precise Pangolin”) Fedora 17 Oracle Linux 6.3  Here's the proof: We don't have time to go into the myriad of smaller improvements such as support for burning audio CDs from a guest, bi-directional clipboard control,  drag-and-drop of files into Linux guests, etc. so we'll leave that as an exercise for the user as soon as you've downloaded from the Oracle or community site and taken a peek at the User Guide. So all in all, a pretty solid release, one that we hope you'll enjoy discovering. - FB 

  Read the article

• The architecture and technologies to use for a secure, fast, reliable and easily scalable web application

  - by DSoul

  ^ For actual questions, skip to the lists down below I understand, that his is a vague topic, but please, before you turn the other way and disregard me, hear me out. I am currently doing research for a web application(I don't know if application is the correct word for it, but I will proceed w/ that for now), that one day might need to be everything mentioned in the title. I am bound by nothing. That means that every language, OS and framework is acceptable, but only if it proves it's usefulness. And if you are going to say, that scalability and speed depend on the code I write for this application, then I agree, but I am just trying to find something, that wouldn't stand in my way later on. I have done quite a bit reading on this subject, but I still don't have a clear picture, to what suits my needs, so I come to you, StackOverflow, to give me directions. I know you all must be wondering what I'm building, but I assure you, that it doesn't matter. I have heard of 12 factor app though, if you have any similar guidelines or what is, to suggest the please, go ahead. For the sake of keeping your answers as open as possible, I'm not gonna provide you my experience regarding anything written in this question. ^ Skippers, start here First off - the weights of the requirements are probably something like that (on a scale of 10): Security - 10 Speed - 5 Reliability (concurrency) - 7.5 Scalability - 10 Speed and concurrency are not a top priority, in the sense, that the program can be CPU intensive, and therefore slow, and only accept a not-that-high number of concurrent users, but both of these factors must be improvable by scaling the system Anyway, here are my questions: How many layers should the application have, so it would be future-proof and could best fulfill the aforementioned requirements? For now, what I have in mind is the most common version: Completely separated front end, that might be a web page or an MMI application or even both. Some middle-ware handling communication between the front and the back end. This is probably a server that communicates w/ the front end via HTTP. How the communication w/ the back end should be handled is probably dependent on the back end. The back end. Something that handles data through resources like DB and etc. and does various computations w/ the data. This, as the highest priority part of the software, must be easily spread to multiple computers later on and have no known security holes. I think ideally the middle-ware should send a request to a queue from where one of the back end processes takes this request, chops it up to smaller parts and buts these parts of the request back onto the same queue as the initial request, after what these parts will be then handled by other back end processes. Something *map-reduce*y, so to say. What frameworks, languages and etc. should these layers use? The technologies used here are not that important at this moment, you can ignore this part for now I've been pointed to node.js for this part. Do you guys know any better alternatives, or have any reasons why I should (not) use node.js for this particular job. I actually have no good idea, what to use for this job, there are too many options out there, so please direct me. This part (and the 2. one also, I think) depend a lot on the OS, so suggest any OSs alongside w/ the technologies/frameworks. Initially, all computers (or 1 for starters) hosting the back end are going to be virtual machines. Please do give suggestions to any part of the question, that you feel you have comprehensive knowledge and/or experience of. And also, point out if you feel that any part of the current set-up means an instant (or even distant) failure or if I missed a very important aspect to consider. I'm not looking for a definitive answer for how to achieve my goals, because there certainly isn't one, for I haven't provided you w/ all the required information. I'm just looking for recommendations and directions on what to look into. Also, bare in mind, that this isn't something that I have to get done quickly, to sell and let it be re-written by the new owner (which, I've been told for multiple times, is what I should aim for). I have all the time in the world and I really just want to learn doing something really high-end. Also, excuse me if my language isn't the best, I'm not a native. Anyway. Thanks in advance to anyone, who takes the time to help me out here. PS. When I do seem to come up w/ a good architecture/design for this project, I will certainly make it an open project and keep you guys up to date w/ it's development. As in what you could have told me earlier and etc. For obvious reasons the very same question got closed on SO, but could you guys still help me?.

  Read the article

• ????????????????? Oracle Solaris ??? - Solaris 11 ????(??)

  - by kazun

  ???????????????? OS ????????????????????? 20 ??????????????????? Solaris?????????????????????? OS????????????????????????Solaris ???????????????????? ??????Oracle Solaris ??????????????6??????????????????Oracle Solaris ?????????????????????? [????????????] ?????(????????????? ???)?????(??????????????)?????(??????????????)?????(????????)???? ?(?????????????????)?????(???????????)(50??) Solaris????? ??: Solaris ??????????????????????????????????????Solaris ??Solaris ???????????????????????????? 10 ??? Solaris ?????????????????????? OS ?????????????????????????????????????????????????????????????? OS ???? Solaris ?????? ??: Solaris ????????????????????????????OS?????????????????????????????????????????????????????????????????????????????????? ???: ??????????????????????? 15 ??????????????????????????????????????????? Solaris ???????????????????????????????????????????????????????????5 ???10 ??????????????????????????? Solaris ???????????? ??: ??? Solaris ????????????????????????????????????????????????????????????????????????????????????????????? OS ?????????????????????????????????????????????????????????????????????????????????????????????? ??: ??????? OS ?????????????????????????????????????????????????????????????????????????DTrace ????????????????????????????? Solaris ???????? ???: 1980 ?????Sun ???????OS???????????????????????????????????????????????????????????????????????????????? ?Solaris ????1988?????Sun ? AT&T ? System V Release 4.0 ?????????????Sun ????????? System V Release 4.0 ?????????? Unix OS ??? SunOS 5.0(?? 1992 ????????? Solaris 2.0)???????????????????? SMP ?????????????????????????????????????????????????????Solaris 2.0 ?????????????? OS ????????(?)???????????????????????????????? 2.1, 2.2, 2.3 ??????????? 2.0 ????????????????? ??: Solaris ??????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????OS?????????? ??: ????????????????????????? ???: ????????????????? OS ??????????? x86 ? SPARC ? 2 ???????????????????????????????????????????????????????????????????????????????????????????????? CPU ????????????????????????????????????????????????????????????????????????????????? Solaris ??? ????? ?? Solaris 2.0 - 2.1 AT&T ? UNIX System V Release 4 ??????????????SMP/?????????????????API ????? SunOS 5.0 ????????Solaris 2.0 ????x86 ?? SPARC ?? Solaris 2.1 ?????????????????????????????? Solaris 2.2 - 2.4 - ???????? (SVR4 ??) - ???????????(2.5.1 ?? PowerPC ?????????) - 2.4 ?? x86 ?????????????????? Solaris 2.6?Solaris 7(2.7 ??????) 64 bit ??(Itanium ?????) Solaris 8 - 9 ?????????? Solaris 10 - 11 ??????????????????(OS ????????????????) Solaris??????? ??: ?????????????????????????????????????????Solaris ?????????????????????????????????????????????????????????????????? ??: ?????????????????? OS ???????????Solaris 2.3 ???????????????????????????????????????????????????????????????????????????????????????????????????? ???: ???????????????????????????????????????????????????????????????????????????????????? OS ????????????? Solaris ??????? ??: ??????????????????????????????????????????????????????????????????????????????????????????????????? ??: ??????????????????????????????????????????????????????????????????????????DTrace ?????????????????????????????????? ??: ????Solaris ? UNIX ????????????????????????????????????? OS ??????????????????????????????????????????????????????????????????????????????????????????????????????????????? Solaris ????????????????????????????????????????????????? OS ??????????????????? Solaris ???????? ??: ??????????????????????????1?? OS ?????????????? OS ??????????????????????????????????????Solaris ????? 1 ?? Solaris ??????????????????OS????????????????? ???: Legacy Container ????????????? Solaris(Solaris 8?Solaris 9) ???????????? ??: Solaris 10 ?????? SMF(Service Management Facility) ??????????????????????????????????????????????????????????????????????????????????????? ??: SMF?FMA (Fault Management Architecture)?????????????????????????????? Solaris ?????????????????????????? ???: ????????????????????????? ??: ?????????????????????1???????????????????????????????????????? Sun ??????????The Network Is The Computer???? ??: ??????Solaris 10 ?????????????????????????????????????????????????????????????????????????????? Solaris?????? ??: Solaris ?????????????????????Sun ?????????????(? 20 ??)??????????????????????????????????????????????????????????????????????????????????????????????????????????????????Sun ????????????????????????????????????????????????????????Sun ?????????????????????????????????????????????????????????????????????????? ???: Solaris ????? SunOS ????????????????????????? OS ??????? ??: ??????????????????????????????Sun ???????????????????????????????????????????????????????????? ??: 1990 ??????????????????? Solaris ???????? ???: ?????X Windows ???? Sun ??????????NeWS??????????????????????????????X Windows ??????????????????????????????????????? Sun ? Solaris ???????????????????????? ??: ???????Solaris ??????????????? OS ??????????????????????????????????????????????????????????????????????????????????????? ??: ????????????????????? Solaris ????????????ZFS ???????????????????????????????? ??: ????? OS ??????? Solaris ??????(???)??????????????? ???: Solaris ???????????????????? Solaris??????Solaris 2.0 ???? 2 ??? 1 ??????????????(?????????)??????Solaris ? 2 ??????????????????????????????????????? 2 ????????????????????????????2 ??? 1 ????????????????????????????????????????????????????????????? ????OS???????????? ???: Solaris ?????? Solaris ????????????OS ??????????????????????????????????????????????????????????????????????????????? ??: ??????????????????????????????????????????????(?)?????????????????????????????????????????????15 ?????????????????????????????????????????????????????????????????????????? ??: Solaris ??????? Solaris ????????????????????????????????????????????????????????? ??: ????????????????????????????????????????????????Solaris ??????????????????????????? ???: ??????????????Solaris ????????????????????????????????????????????????????????????????????????????????????? Solaris ?????????? ??: Solaris ???????????????????????????????????????????????????? ??: ????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ???: 1994 ?????????????????????????????????????? ??: ??????????????????????????Solaris ????????????????????????????????????? ???: ???????????????? ??: ???Solaris ?????? 2 ?????????????????????????????????????? Solaris ?????????????????????????????????????????????????????????????????????????????????????????????OS?????????????????????????????????????????????????????Solaris ???????????? ??????Oracle Solaris ????????????6??????????????????Oracle Solaris ??????????????????????

  Read the article

• postfix with mailman

  - by Thufir

  What should happen is that [email protected] should be delivered to that users inbox on localhost, user@localhost. Thunderbird works fine at reading user@localhost. I'm just using a small portion of postfix-dovecot with Ubuntu mailman. How can I get postfix to recognize the FQDN and deliver them to a localhost inbox? root@dur:~# root@dur:~# tail /var/log/mail.err;tail /var/log/mailman/subscribe;postconf -n Aug 27 18:59:16 dur dovecot: lda(root): Error: chdir(/root) failed: Permission denied Aug 27 18:59:16 dur dovecot: lda(root): Error: user root: Initialization failed: Initializing mail storage from mail_location setting failed: stat(/root/Maildir) failed: Permission denied (euid=65534(nobody) egid=65534(nogroup) missing +x perm: /root, dir owned by 0:0 mode=0700) Aug 27 18:59:16 dur dovecot: lda(root): Fatal: Invalid user settings. Refer to server log for more information. Aug 27 20:09:16 dur postfix/trivial-rewrite[15896]: error: open database /etc/postfix/transport.db: No such file or directory Aug 27 21:19:17 dur postfix/trivial-rewrite[16569]: error: open database /etc/postfix/transport.db: No such file or directory Aug 27 22:27:00 dur postfix[17042]: fatal: usage: postfix [-c config_dir] [-Dv] command Aug 27 22:29:19 dur postfix/trivial-rewrite[17062]: error: open database /etc/postfix/transport.db: No such file or directory Aug 27 22:59:07 dur postfix/postfix-script[17459]: error: unknown command: 'restart' Aug 27 22:59:07 dur postfix/postfix-script[17460]: fatal: usage: postfix start (or stop, reload, abort, flush, check, status, set-permissions, upgrade-configuration) Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: error: open database /etc/postfix/transport.db: No such file or directory Aug 27 21:39:03 2012 (16734) cola: pending "[email protected]" <[email protected]> 127.0.0.1 Aug 27 21:40:37 2012 (16749) cola: pending "[email protected]" <[email protected]> 127.0.0.1 Aug 27 22:45:31 2012 (17288) gmane.mail.mailman.user.1: pending [email protected] 127.0.0.1 Aug 27 22:45:46 2012 (17293) gmane.mail.mailman.user.1: pending [email protected] 127.0.0.1 Aug 27 23:02:01 2012 (17588) test3: pending [email protected] 127.0.0.1 Aug 27 23:05:41 2012 (17652) test4: pending [email protected] 127.0.0.1 Aug 27 23:56:20 2012 (17985) test5: pending [email protected] 127.0.0.1 alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# there's definitely a transport problem: root@dur:~# root@dur:~# root@dur:~# grep transport /var/log/mail.log | tail Aug 27 22:29:19 dur postfix/trivial-rewrite[17062]: warning: hash:/etc/postfix/transport lookup error for "[email protected]" Aug 27 22:29:19 dur postfix/trivial-rewrite[17062]: warning: transport_maps lookup failure Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: error: open database /etc/postfix/transport.db: No such file or directory Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport lookup error for "*" Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport lookup error for "*" Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport is unavailable. open database /etc/postfix/transport.db: No such file or directory Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: hash:/etc/postfix/transport lookup error for "[email protected]" Aug 27 23:39:17 dur postfix/trivial-rewrite[17794]: warning: transport_maps lookup failure root@dur:~# trying to add the transport file: EDIT root@dur:~# root@dur:~# touch /etc/postfix/transport root@dur:~# ll /etc/postfix/transport -rw-r--r-- 1 root root 0 Aug 28 00:16 /etc/postfix/transport root@dur:~# root@dur:~# cd /etc/postfix/ root@dur:/etc/postfix# root@dur:/etc/postfix# postmap transport root@dur:/etc/postfix# root@dur:/etc/postfix# cat transport

  Read the article

• High apache load but little traffic logged

  - by nrambeck

  I recently installed Varnish to sit in front of Apache on a dedicated server running a single site. It appears to be working well, but the load on Apache is still very high. What doesn't make sense is that the Apache access log shows almost no traffic getting past Varnish. When I tail the apache log I see about 1-3 hits per second come through. Here is what the load on Apache looks like : USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND apache 13834 8.1 1.0 107716 34164 ? S 08:24 0:02 /usr/sbin/httpd apache 13835 8.1 1.0 107716 33856 ? S 08:24 0:02 /usr/sbin/httpd apache 11483 7.9 0.9 105916 30788 ? S 08:23 0:06 /usr/sbin/httpd apache 12255 7.5 1.0 107476 33312 ? S 08:24 0:04 /usr/sbin/httpd apache 9340 7.2 1.1 107732 34916 ? R 08:23 0:09 /usr/sbin/httpd apache 12029 6.8 0.9 106908 30416 ? S 08:24 0:04 /usr/sbin/httpd apache 11577 6.7 1.0 107192 34180 ? S 08:24 0:05 /usr/sbin/httpd apache 11486 6.6 1.0 106176 33112 ? S 08:23 0:05 /usr/sbin/httpd apache 11796 6.4 1.0 106936 31916 ? S 08:24 0:04 /usr/sbin/httpd apache 13815 6.3 1.0 107988 34464 ? S 08:24 0:02 /usr/sbin/httpd apache 18089 6.3 1.3 107444 43212 ? S 08:11 0:52 /usr/sbin/httpd apache 11797 5.9 1.0 107716 34580 ? S 08:24 0:04 /usr/sbin/httpd apache 7655 5.9 0.0 0 0 ? Z 08:22 0:09 [httpd] <defunct> mysql 8033 5.9 6.2 318240 199512 ? Sl May14 352:34 /usr/libexec/mysqld --basedir=/usr --datadir=/var/lib/mysql --user=mysql --pid-file=/va apache 11488 5.8 0.9 106924 31632 ? S 08:23 0:04 /usr/sbin/httpd apache 9375 5.7 1.1 106956 35552 ? S 08:23 0:07 /usr/sbin/httpd apache 3551 5.6 1.1 106956 36140 ? S 08:20 0:14 /usr/sbin/httpd apache 7657 5.6 1.0 106968 32472 ? S 08:22 0:09 /usr/sbin/httpd apache 11433 5.6 1.0 107716 34396 ? S 08:23 0:04 /usr/sbin/httpd apache 5505 5.5 1.1 106944 34924 ? S 08:21 0:12 /usr/sbin/httpd apache 7172 5.3 1.1 106972 35368 ? S 08:22 0:09 /usr/sbin/httpd apache 10088 5.2 0.9 106160 31240 ? S 08:23 0:04 /usr/sbin/httpd apache 7656 5.1 1.0 106436 34388 ? S 08:22 0:08 /usr/sbin/httpd apache 3468 5.0 1.1 107716 35968 ? S 08:20 0:13 /usr/sbin/httpd apache 14242 4.8 1.0 107728 33032 ? S 08:25 0:00 /usr/sbin/httpd apache 3578 4.8 1.1 107988 35964 ? S 08:20 0:12 /usr/sbin/httpd apache 28192 4.8 1.2 106944 38060 ? S 08:17 0:23 /usr/sbin/httpd apache 3277 4.6 1.1 106956 35688 ? S 08:20 0:13 /usr/sbin/httpd apache 15434 3.7 0.7 106908 24684 ? S 08:25 0:00 /usr/sbin/httpd There is a default apache log and then one other VirtualHost log setup. I'm concerned that Apache is handling some kind of traffic that is not being logged. Is that possible? And is there anything I can do to capture that traffic?

  Read the article

• FFSERVER - streaming an ASF video as Webm output

  - by Emmanuel Brunet

  I'm trying to stream an IP webcam ASF live stream to a ffserver to output a webm video format. The server starts successfully but the ffserver commands used to feed the ffserver fails and generates a core dump. Environment Debian 7.5 ffmpeg 2.2 Input stream $ ffprobe http://account:password@webcam/videostream.asf Input #0, asf, from 'http://admin:alpha1237@webcam/videostream.asf': Duration: N/A, start: 0.000000, bitrate: 32 kb/s Stream #0:0: Video: mjpeg (MJPG / 0x47504A4D), yuvj422p(pc), 640x480, 25 tbr, 1k tbn, 1k tbc Stream #0:1: Audio: adpcm_ima_wav ([17][0][0][0] / 0x0011), 8000 Hz, 1 channels, s16p, 32 kb/s ffserver configuration my ffserver configuration is : Port 8091 RTSPPort 554 BindAddress 192.168.1.62 MaxHTTPConnections 1000 MaxClients 100 MaxBandwidth 1000 CustomLog - <Feed webcam.ffm> File /tmp/webcam.ffm FileMaxSize 500M ACL allow localhost ACL allow 192.168.0.0 192.168.255.255 </Feed> <Stream webcam.webm> # Output stream URL definition Feed webcam.ffm # Feed from which to receive video Format webm # Audio settings AudioCodec vorbis AudioBitRate 64 # Audio bitrate # Video settings VideoCodec libvpx VideoSize 640x480 # Video resolution VideoFrameRate 25 # Video FPS AVOptionVideo flags +global_header # Parameters passed to encoder # (same as ffmpeg command-line parameters) AVOptionVideo cpu-used 0 AVOptionVideo qmin 10 AVOptionVideo qmax 42 AVOptionVideo quality good AVOptionAudio flags +global_header PreRoll 15 StartSendOnKey # VideoBitRate 32 # Video bitrate </Stream> <Stream status.html> Format status # Only allow local people to get the status ACL allow localhost ACL allow 192.168.0.0 192.168.255.255 </Stream> ffmpeg feed I run the following command that fails $ ffmpeg -i http://account:password@webcam/videostream.asf http://192.168.1.62:8091/webcam.ffm http://192.168.1.62:8091/webcam.ffm Input #0, asf, from 'http://account:password@webcam/videostream.asf': Duration: N/A, start: 0.000000, bitrate: 32 kb/s Stream #0:0: Video: mjpeg (MJPG / 0x47504A4D), yuvj422p(pc), 640x480, 25 tbr, 1k tbn, 1k tbc Stream #0:1: Audio: adpcm_ima_wav ([17][0][0][0] / 0x0011), 8000 Hz, mono, s16p, 32 kb/s [swscaler @ 0x36a80c0] deprecated pixel format used, make sure you did set range correctly Segmentation fault I tryed $ ffmpeg -i http://account:password@webcam/videostream.asf -pix_fmt yuv420p http://192.168.1.62:8091/webcam.ffm But it raises the same error. Thanks for your help Edit For an easy testing (I thought), I tried to publish the whole ASF stream as is, meaning connecting the ASF webcam output stream to the ffserver that outputs ASF format too. And thus with mirrored encoding so I changed the ffserver configuration to ... <Stream webcam.asf> Feed webcam.ffm Format asf VideoFrameRate 25 VideoSize 640X480 VideoBitRate 256 VideoBufferSize 1000 VideoGopSize 30 AudioBitRate 32 StartSendOnKey </Stream> ... And the output is now : Input #0, asf, from 'http://admin:alpha1237@webcam/videostream.asf': Duration: N/A, start: 0.000000, bitrate: 32 kb/s Stream #0:0: Video: mjpeg (MJPG / 0x47504A4D), yuvj422p(pc), 640x480, 1k tbr, 1k tbn, 1k tbc Stream #0:1: Audio: adpcm_ima_wav ([17][0][0][0] / 0x0011), 8000 Hz, mono, s16p, 32 kb/s [swscaler @ 0x3d620c0] deprecated pixel format used, make sure you did set range correctly Output #0, ffm, to 'http://192.168.1.62:8091/webcam.ffm': Metadata: creation_time : now encoder : Lavf55.40.100 Stream #0:0: Audio: wmav2, 22050 Hz, mono, fltp, 32 kb/s Metadata: encoder : Lavc55.64.100 wmav2 Stream #0:1: Video: msmpeg4v3 (msmpeg4), yuv420p, 640x480, q=2-31, 256 kb/s, 1k fps, 1000k tbn, 1k tbc Metadata: Stream mapping: Stream #0:1 -> #0:0 (adpcm_ima_wav -> wmav2) Stream #0:0 -> #0:1 (mjpeg -> msmpeg4) Press [q] to stop, [?] for help Segmentation fault I can't even forward the stream.

  Read the article

• Locating Rogue Perl Script

  - by Gary Garside

  I've been trying to source the location of a perl script which is causing havoc on a server which i control. I'm also trying to find out exactly how this script was installed on the server - my best guess is through a wordpress exploit. The server is a basic web setup running Ubuntu 9.04, Apache and MySQL. I use IPTables for firewall, the site runs around 20 sites and the load never really creeps above 0.7. From what i can see the script is making outbound connection to other servers (most likely trying to brute force entry). Here is a top dump of one of the processes: PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 22569 www-data 20 0 22784 3216 780 R 100 0.2 47:00.60 perl The command the process is running is /usr/sbin/sshd . I've tried to find an exact file name but im having no luck... i've ran a lsof -p PID and here is the output: COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME perl 22569 www-data cwd DIR 8,6 4096 2 / perl 22569 www-data rtd DIR 8,6 4096 2 / perl 22569 www-data txt REG 8,6 10336 162220 /usr/bin/perl perl 22569 www-data mem REG 8,6 26936 170219 /usr/lib/perl/5.10.0/auto/Socket/Socket.so perl 22569 www-data mem REG 8,6 22808 170214 /usr/lib/perl/5.10.0/auto/IO/IO.so perl 22569 www-data mem REG 8,6 39112 145112 /lib/libcrypt-2.9.so perl 22569 www-data mem REG 8,6 1502512 145124 /lib/libc-2.9.so perl 22569 www-data mem REG 8,6 130151 145113 /lib/libpthread-2.9.so perl 22569 www-data mem REG 8,6 542928 145122 /lib/libm-2.9.so perl 22569 www-data mem REG 8,6 14608 145125 /lib/libdl-2.9.so perl 22569 www-data mem REG 8,6 1503704 162222 /usr/lib/libperl.so.5.10.0 perl 22569 www-data mem REG 8,6 135680 145116 /lib/ld-2.9.so perl 22569 www-data 0r FIFO 0,6 157216 pipe perl 22569 www-data 1w FIFO 0,6 197642 pipe perl 22569 www-data 2w FIFO 0,6 197642 pipe perl 22569 www-data 3w FIFO 0,6 197642 pipe perl 22569 www-data 4u IPv4 383991 TCP outsidesoftware.com:56869->server12.34.56.78.live-servers.net:www (ESTABLISHED) My gut feeling is outsidesoftware.com is also under attacK? Or possibly being used as a tunnel. I've managed to find a number of rouge files in /tmp and /var/tmp, here is a brief output of one of these files: #!/usr/bin/perl # this spreader is coded by xdh # xdh@xxxxxxxxxxx # only for testing... my @nickname = ("vn"); my $nick = $nickname[rand scalar @nickname]; my $ircname = $nickname[rand scalar @nickname]; #system("kill -9 `ps ax |grep httpdse |grep -v grep|awk '{print $1;}'`"); my $processo = '/usr/sbin/sshd'; The full file contents can be viewed here: http://pastebin.com/yenFRrGP Im trying to achieve a couple of things here... Firstly i need to stop these processes from running. Either by disabling outbound SSH or any IP Tables rules etc... these scripts have been running for around 36 hours now and my main concern is to stop these things running and respawning by themselves. Secondly i need to try and source where and how these scripts have been installed. If anybody has any advise on what to look for in access logs or anything else i would be really grateful. Thanks in advance

  Read the article

• Useful software for netbook?

  - by Moayad Mardini

  I'm looking for recommendations of good software that are particularly useful for netbooks. Software that run great on small screens and low CPU/RAM requirments. I'll start off with the following : Operating Systems: Ubuntu Netbook Remix. Easy Peasy: A fork of Ubuntu Netbook Remix that was once called UBuntu EEE. It isn't just for eeePCs though. Definitely worth a look if vanilla Netbook Remix isn't cutting it. (MarkM) Damn Small Linux (Source) Windows 7: With trimming the installation or compressing the Windows directory to fit on an 8GB SSD. (Will Eddins) nLite: A utility to install a lightweight version of Windows XP without the unnecessary components (like Media Player, Internet Explorer, Outlook Express, MSN Explorer, Messenger...). Utilites: TouchFreeze: To disable the touch pad while typing (Source) InSSIDer: Not only does it make it easier to find and keep a wireless connection, but it turns a netbook into the perfect mobile tool for troubleshooting wireless networks. (phenry) AltMove: Adds more functionality to your mouse for interacting with windows. (Rob) ASUS Font Resizer Utility and other tools by ASUS, specific to ASUS Eee PC series. Internet: Run FileZilla FTP client for a small screen : You can hide a lot of FileZilla's interface parts in the View menu, even the directory trees. Go into Settings = Interface and move the message log next to the transfer queue, if you haven't hidden them both or you want to see them. Select a theme with 16x16 icons. (Source) IDEs and Text Editors: Best lightweight IDE/Text Editor: A question on Stack Overflow that has many good suggestions of IDEs and general text editors for programmers. What’s a good linux C/C++ IDE for a low-res screen?: IDEs for Linux-powered netbooks. Online tools: Dropbox: Since the Netbook has limited disk space, you would like to use Cloud Apps like Dropbox and Ubuntu One so that you don't run out of space especially if you are on a holiday. Later when you go back to your desktop with big hard disk,you can take out the files from your dropbox repo. (Manish Sinha) Google products: like Docs, Calendar and Reader (aviraldg) Web sites and software lists: Netbookfiles.com: Netbook specific software downloads. Software Apps to Maximise your Netbook Battery Power: Netbooks are known for their portability. Not only are they small and lightweight but with their increased power efficiency, batteries can last much longer than conventional laptops. This also means you no longer have to carry a power adapter with you! Several brands emphasis the longevity of the battery as a strong selling point, and for those people who travel a lot, it sure is. Free Must-Have Netbook Apps: Finding software for netbooks can present challenges due to limited hard drive space, processor power, RAM, and screen real-estate. That doesn't mean you have to do without essential programs. The apps below cover all the bases -- entertainment, productivity, security, and communication -- without compromising on performance or usability. Best of all, they're free! Useful Netbook Software: With short battery lives and small resolution screens Netbooks, unlike many other computers on the market, could so with some specific software for their use. Now, not all of those I’ve found are specifically designed for Netbooks, but all are relevant. And they’re designed for Windows XP. The question is community wiki, so feel free to edit it. Updated, thank you all for suggestions.

  Read the article

< Previous Page | 400 401 402 403 404 405 406 407 408 409 410 411  | Next Page >