Search Results

Search found 1360 results on 55 pages for 'is it plugged in'.

Page 42/55 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• Why is my Compaq NC8430 laptop so darned HOT ?

  - by Cheeso

  For a long time I've had a Compaq nc8430 laptop. It's nearly 3 years old now. Originally shipped with WinXP, but I installed Vista on it. From the very start it was not a good experience. This thing has one of those "stickpoint" mice, which I like. After a while, I noticed that the computer was generating lots and lots of heat. So much heat, that the stickpoint bumper would melt and disintegrate. Normally I would expect heat if the CPU was working hard, but even when the CPU was idle, the computer was hot. Much too hot to keep on my lap. Turns out this is not an uncommon problem. I installed the HWmonitor tool, and found that the CPU temp was 82C when it was plugged in - pretty darn hot. And because the temp was so high, the fan never turned off, so the laptop was as loud as a jet engine, always. If I unplugged it from A/C power, the screen would dim and the temperature would decrease, and the fan noise would lessen, but still, it was too loud. It's totally unusable. What is the problem?

  Read the article

• How to plug power/reset buttons from case to motherboard leads?

  - by MaxMackie

  I have a motherboard I salvaged from a pre-assembled computer. Except now I'm trying to use it in my own custom build. The problem is, this motherboard doesn't have any documentation because it was never meant to be used by consumers (as far as I know). I need to plug in my case's power/reset/hdd-light plugs into the motherboard. I usually check the documentation of the board to see which leads go to what connector, but I have no documentation for the board. So, as I see it, I have two options: I find the documentation (I've emailed gateway customer service, but I'm unsure of how successful I'll be with that). I simply test the leads one after the other (can this cause damage if plugged into the wrong leads?) However, there might even be a standard for which leads do what action (I'm not sure about this). For reference, my motherboard's SN/MD (?) is: H57M01G1-1.1-8EKS3H Does anyone have any idea if I can find documentation or find another way to be sure if my connections are correct?

  Read the article

• Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace

  - by Nick

  I have an laptop top hard drive I was trying to use to my new media computer. The case is small and can accommodate for 2 2.5" drives, no 3.5" drives. I had been using the hard drive as storage hard drive until now. When I go to install Windows on the hard drive first I'm prompted at the bios of: Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace. And then again in the Windows Setup, informing me that the hard drive is bad. So I did a full format of the drive and tried again. Same error. So I took it out and hooked it back up to my other computer via an Sata usb adapter kit (maybe the cause?). The hard drive is recognized fine and when I scanned it for errors by going: right click -> properties -> tools -> error checking It returns that the hard drive is fine. I have tried 3 different SATA cables and multiple jumpers. When I plugged in my 1.5 tb 3.5" drive the computer that gives me the S.M.A.R.T. error on the 2.5" drive, recognizes it with no problems. Any ideas on why this is happening and how I can fix it?

  Read the article

• Windows Vista: Screen remains darkened for 30-60 seconds *after* UAC prompt

  - by sf2k

  Fixing someone's Vista computer. Process: I click any program or process that opens a User Account Control prompt. Screen goes dim so you may hit Continue to perform a secure user action. I click Continue Screen goes black for 30 seconds to 1 minute while you wait for the screen to return. In another example I click Cancel and screen still then goes black for 30 seconds to a minute. In that timeframe a chime goes off while you wait. (No chime if it was being cancelled.) Then screen comes back to continue with whatever. Something is occurring after the UAC prompt. Considering everything is practically a UAC acceptance this can get pretty annoying pretty quickly. Laptop has external monitor to regular external plug. Works fine. Laptop also has USB IOGEAR additional external video card. This is problematic but when unplugged same above behaviour occurs. I've ruled out monitor interference since same blackout after the UAC prompt appears with external monitors plugged in or when rebooted with no external monitors. Any suggestions on how to address this problem?

  Read the article

• Why won't 2GB of ram across 3 of 4 slots work on my motherboard (max 2GB)?

  - by Andrew

  My desktop is an old home-built machine circa 200[5-6] running Ubuntu 11.10 (but this is not relevant because I'm reading available ram from BIOS loading screen), with an ASUS P5GPL motherboard, not X or X-SE - it has four slots. I'm mainly a laptop person, but keep this around for running a server from if needed, backing up to, seeding Ubuntu to people from, etc… It has four (DDR) ram slots, two black and two blue, in the order black-blue-black-blue (I will call them D, C, B, and A, respectively) with some space in the middle. The blue ones are the closest to the processor. I used to have two 512MB chips in the two blue slots. I just got a 1GB chip and plugged it into one of the black slots; my system didn't recognize it. I messed around and discovered that it will not recognize chips in many positions, and I couldn't get it to recognize all three of these chips at the same time. In particular, if I put the 512MB chips in A and B it would only use 1, but AC, AD, BD, and CD worked. I didn't try BC, I believe. Only some of these continue to work when I switch the 1GB chip into one of these positions. Can I have some advice as to how to position these chips to get all 2GB used? How about if I get another 1GB chip - where should I put the two? And what about the RAM maximum Crucial says? Can I go above 2GB, if I get another 1GB chip? Right now, I have a 512MB chip in A and the 1GB chip in C. EDIT: I read some other posts and tried dmidecode in Ubuntu to clarify the max memory question, that wasn't a major part anyways. It says my max memory module size is 1024M (OK) and my max memory size is 4096M (doesn't agree with Crucial OR the Asus web site, maybe it will only work while in Linux and BIOS won't OK it?).

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• Two NIC's 2 Internet Connections, 1 Windows Server 2008 RC2, Routing help required

  - by PJZ

  Hello, I have a Windows 2008 server and 4 other client machines on my home network. I have two internet connections. The main connection is setup with a home router and DHCP on that for all the clients on the network. The secondary connection is just a cable modem which is plugged directly into the server. Local Area Connection: This NIC has an external IP and is connected to the Cable Modem. Local Area Connection 2: This NIC has an internal IP (192.168.0.102) and allows access to all the internal computers. It also has internet access via the local router. So here lies the problem, I want to use the Cable connection on the server for the internet traffic (so that the traffic for server/clients are seperated) but I also need to maintain local access. I am wondering how to make it so that all the internet traffic goes via that NIC because at the moment it goes through the local NIC. As a secondary problem I would also like to forward the connection of one application used by the clients via the server and the cable/server internet because of poor routing for it on the main connection. This perhaps is something for another question though. Thanks for any help you can offer me. Regards PJ

  Read the article

• OS X can't copy files from Windows Home Server...over wifi.

  - by John Clayton

  I'm a brand spanking new user of OS X, coming from a lifetime of Windows use. I've been setting up my new Macbook Pro and have run into a very unusual problem. Over wifi, I am unable to copy files to or from my Windows Home Server. The problem seems to exist only over wifi, and only to WHS. Here are the details of my setup: 2010 Macbook Pro (Core i7), OS X 10.6.3 Windows Home Server PP3 (virtualized in XenServer 5.5) Windows 7 Ultimate x64 desktop Windows 7 Ultimate x64 in Boot Camp D-Link DIR-655 wireless N router Here is what I've done to narrow down the problem: Files copy fine from WHS to OS X when using gigabit ethernet Files copy fine from desktop to OS X when using gigabit ethernet Files fail to copy from WHS to OS X when using wifi (error -51) Files copy fine from desktop to OS X when using wifi Files copy fine from WHS to Boot Camp when using wifi Files copy fine from desktop to Boot Camp when using wifi From what I can tell, it seems to be some sort of issue between OS X and WHS, but I can't for the life of me see what would be different between shares on WHS and my desktop. They are both connected using smb://ADDRESS (I've tried both by IP and name). I can browse the shares on the WHS, but copying to OS X fails. I originally found the issue while installing VS2010 off an ISO from WHS, mounted to a Windows 7 VM using VMware Fusion. During the installation the VM was unusable - even the clock got behind the host be about 8 minutes. Once I plugged in the ethernet and disabled the wifi things picked up and finished quickly. The Fusion 3.1 RC is the only I think of that I installed that may have messed with the wifi driver. I've also tried resetting the wifi router, and have changed it from being G & N to N-only. Under Boot Camp I get similar speeds as my wife's N laptop. Any ideas? Thanks!

  Read the article

• Windows 7 wireless not seeing any networks

  - by jkohlhepp

  I think I have managed to confuse Windows 7. When I did the install, I had the network cable plugged in to my router, but the wireless card was also enabled. During the install, Windows 7 seemed to see my wireless network and even asked me for the WEP key. I know that it used the WEP key because I initially entered an invalid one and it gave me an error. Then the network said "SoAndSoWireless Connected". However, when I unplug or disable my wired network card, then I have no internet, and it can't see any networks. When I plug in the wired network card, it says "SoAndSoWireless Connected". Under Network and Internet Network Connections I have "Local Area Connection" and "Wireless Network Connection". The wired one's status is "SoAndSoWireless" and the wireless status is "Not Connected". Also, the wireless connection can't seem to see any other wireless networks in the area and I know there are tons. My neighbors have several. I've somehow seemingly confused Windows 7 into thinking that my wired network card is my wireless card or something. Any ideas on how to un-confuse it? This is a desktop machine by the way, if it matters. EDIT: Ah, I think part of the problem is that I named my network accidentally the same as the name of the wireless network being broadcast by the wireless router. So that might be why it says that name on the hard-wired connection. Perhaps the drivers just are completely not working for the wireless card. Thanks, ~ Justin

  Read the article

• Mac Mail sent messages not in sent folder

  - by Elizabeth Akers

  Hi. My powerbook G4 has been lobbying for a furlough recently, and its latest prank is to not show sent messages in my sent mailbox. I have always had a copy of every sent message, and now, for some unknown reason, I can only see sent messages from May 7 and earlier. When I did a test, and sent myself an email, it shows up fine in my inbox, but there's nothing in the sent folder. Weird. It also has the little arrow next to messages that I replied to in the inbox. I guess I'm going to have to cc myself on everything until I get this fixed. Also, it's got another new trick, which I'm assuming is unrelated, but I mention it here just in case it is: the battery says it's "good" and has a cycle count of 0, and a full charge capacity of 2139, but for some reason it's all of a sudden not charging when it's plugged in. It works fine when connected to the wall, but there is no battery life at all. Zip. Any thoughts? Is it just time for a new 'book? This one just got back from Apple, having its harddrive replaced for the fourth time (for free, but seriously, this thing is a lemon). Thanks so much, Elizabeth

  Read the article

• Wireless USB keyboard and mouse can wake system, but then receiver is inactive

  - by BlueMonkMN

  I have a Microsoft brand USB device that acts as a receiver for a wireless Microsoft Keyboard and a wireless Mouse. When it's operating normally, there are LEDs on the device indicating Caps Lock, Num Lock and Function Lock, of which the latter 2 are usually lit. It is plugged into a Dell Isnpiron 531 with Windows 7 32-bit running on an AMD Athlon 64 X2 Dual Core processor 5000+. When the computer goes to sleep (the power indicator on the main box is flashing), I can wake it by moving the mouse. So far all is good. However, something changed in, I think, the past couple weeks (I suspect due to a Microsoft driver update problem). Before the change, after waking the computer, everything would operate normally as far as I could tell, but now after waking the computer, the receiver has no lights on, and the keyboard and mouse are completely unresponsive (which is odd, considering the mouse woke up the computer). There is a button on the receiver that's supposed to reset the wireless connection and flash the lights while it does so, but it has no effect in this state. It's like the receiver doesn't have power (but how would the system know I moved the mouse, unless the power was on until it woke up?). I have checked the BIOS/CMOS settings or whatever you call them, and did not see anything related to USB in the power management section. I have checked Windows 7 device manager and ensured that all the USB Root Hub devices have the setting unchecked for allowing the USB power to be turned off. Like I said, this was working before, and the only thing I can think of that's changed is applying Windows Updates.

  Read the article

• Data recovery on a corrupted 3TB disk

  - by Mark K Cowan

  Short version I probably need software to run a deep-scan recovery (ideally on Linux) to find files on NTFS filesystem. The file data is intact, but the references are no longer present. Analogous to recovering data from a "quick-formatted" partition. Hopefully there is a smarter way available than deep-scan, one which would recover filenames and possibly paths. Long version I have a 3TB disk containing a load of backups. Windows 7 SP1 refused to detect the disk when plugged in directly via SATA, so I put it on a USB/SATA adaptor which seemed to work at first. The SATA/USB adaptor probably does not support disks over 2.2TB though. Windows first asked me if I wanted to 'format' the disk, then later showed me most of the contents but some folder were inaccessible. I stupidly decided to run a CHKDSK on my backup disk, which made the folders accessible but also left them empty. I connected this disk via SATA to my main PC (Arch Linux). I tried: testdisk ntfsundelete ntfsfix --no-action (to look for diagnostically relevant faults, disk was "OK" though) to no avail as the files references in the tables had presumably been zeroed out by CHKDSK, rather than using a typical journal'd deletion). If it is useful at all, a majority of the files that I want to recover are JPEG, Photoshop PSD, and MPEG-3/MPEG-4/AVI/MKV files. If worst comes to worst, I'll just design my own sector scanner and use some simple heuristic-driven analysis to recover raw binary blocks of data from the disk which appears to match the structures of the above file types. I am unfamiliar with the exact workings of NTFS but used to be proficient at recovering FAT32 systems with just a hex-editor, so I can provide any useful diagnostic information if you let me know how to find it! My priorities in ascending order of importance for choosing the accepted answer: Restores directory structure Recovers many filenames in addition to the file data Is free / very cheap Runs on Linux Recovers a majority of file data The last point is the most important, but the more of the higher points you match the more rep you'll probably get :)

  Read the article

• Disaster After Removing Two HDD From LaCie RAID 0 Case

  - by John

  This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

  Read the article

• cisco 2900xl - SNMP - Get mac address of device connected to an interface

  - by ankit

  Hello all, Basically what i want to do is to find out what is the mac address of a device plugged in to an interface on the switch (FastEthernet0/1 for example) reading through the switch documentaion i found out that i can configure snmp trap on it to make it notify of any new mac address the switch detects by using the command snmp-server enable traps mac-notifiction but for some reason my switch does not support this feature. the only options i see are CORE_SWITCH(config)#snmp-server enable traps ? c2900 Enable SNMP c2900 traps cluster Enable Cluster traps config Enable SNMP config traps entity Enable SNMP entity traps hsrp Enable SNMP HSRP traps snmp Enable SNMP traps vlan-membership Enable VLAN Membership traps vtp Enable SNMP VTP traps <cr> so the other way would be for me to run a cronjon on my gateway to poll the switch periodically using snmp to get new mac addresses i have looked everywhere but cant seem to find the OID that would provide me this information. any help i can get would me very much appreciated ! here's the output from "show version" on my switch Cisco Internetwork Operating System Software IOS (tm) C2900XL Software (C2900XL-C3H2S-M), Version 12.0(5.4)WC(1), MAINTENANCE INTERIM SOFTWARE Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Tue 10-Jul-01 11:52 by devgoyal Image text-base: 0x00003000, data-base: 0x00333CD8 ROM: Bootstrap program is C2900XL boot loader CORE_SWITCH uptime is 1 hour, 24 minutes System returned to ROM by power-on System image file is "flash:c2900XL-c3h2s-mz.120-5.4.WC.1.bin" cisco WS-C2912-XL (PowerPC403GA) processor (revision 0x11) with 8192K/1024K bytes of memory. Processor board ID FAB0409X1WS, with hardware revision 0x01 Last reset from power-on Processor is running Enterprise Edition Software Cluster command switch capable Cluster member switch capable 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:01:42:D0:67:00 Motherboard assembly number: 73-3397-08 Power supply part number: 34-0834-01 Motherboard serial number: FAB040843G4 Power supply serial number: DAB05030HR8 Model revision number: A0 Motherboard revision number: C0 Model number: WS-C2912-XL-EN System serial number: FAB0409X1WS Configuration register is 0xF thanks, -ankit

  Read the article

• How do I diagnose a bottleneck in an Intel Atom based Ubuntu server?

  - by Jon Cage

  I have a small media server at home which has software raid and a gigabit link to the rest of my network. For some reason though, I only get ~10MB/s transfers when copying to/from the server. I use software RAID5 (mdadm) over 4 1TB disks. On top of that I then use LVM to give me a huge pool of disk space which is then split up into multiple partitions which can be resized as and when they need it. I'm guessing this it most likely the cause, but I'd like to know for sure where the root cause is. So, how can I benchmark network throughput (Windows 7 desktop <- Ubuntu server) and hard disk performance to try and identify where my bottleneck might be? [Edit] If anyone's interested, the motherboard is an Intel Desktop Board D945GCLF2. So that's a 300 series Atom processor with the Intel® 945GC Express Chipset [Edit2] I feel like such a fool! I just checked my desktop and I had the slower of the two onboard NICs plugged in so the server is probably not at fault here. Transferring a copy of ubuntu off the server I get ~35-40MB/s according to Windows 7. I'll do those HD tests when I get a chance though (just for completeness).

  Read the article

• What to do before connecting Ubuntu Server to the internet for the first time?

  - by CodeMonkey

  I just finished installing Ubuntu Server 12.10 on an Asus Eee PC 1000H (to be used as a home server/sandbox) from USB. I installed this software during installation: OpenSSH server LAMP server Samba file server Virtual Machine host I won't use 2, 3 or 4 for a while though. Can/should I turn these off somehow? I have turned home directory encryption on. Security updates are installed automatically. I have chosen a strong password for the single user. I have never plugged in the internet cable so far. Before doing so I'd like to ask: What can/should I do/install to increase security before connecting to the internet? Firewall? Fail2ban? Users/Passwords? Encryption? Enable/Disable functionality? etc. I'm sorry if you get this question a lot. I've searched around quite a while, but it still feels like I might overlook something important.

  Read the article

• Getting the most out of a Mac mini as a media center

  - by celebritarian

  Hello! I own an old Mac mini from 2006 (maybe early 2007). It's got an Intel Core Solo 32-bits CPU and 512 MB RAM. 160 GB HDD. The GPU is an integrated chip… Currently, my Mini is sitting under my LCD TV (720p). It's plugged in via a DVI to HDMI cable. It's currently running Leopard. And unfortunately, Snow Leopard can't be installed on a device with less than 1 GB of RAM… So, my Mac mini isn't exactly powerful. Also, it's slow and Mac OS X is not a pleasant experience on my Mini right now. It feels slow and heavy. I want to use my Mac mini as a media center/player. I want to be able to play video files in 720p (H.264, Matroska/MOV files). So basically, playing high-def videos is all I want to do with my Mini. What OS should I install? Stick to OS X? Optimize for video playback? Or should I install another OS — like Win XP, Ubuntu or any other Linux dist? Then, will my Mini be able to play 720p videos smoothly, even though the CPU and GPU aren't that powerful and with the limit of 512 MB of RAM? Appreciate all help. Thanks in advance!

  Read the article

• Windows XP, Preference menu's hidden for many programs

  - by Jestep

  I don't know when this started happening, but it has been several months since I first noticed it. Basically, when I go to a preferences menu of some programs, the preferences window is completely hidden, but the program see's it as being open. This prevents me from interacting with the preferences and the actual program. So far I've noticed it on Adobe Illustrator and Netbeans. Illustrator when I select edit - Preferences - An Option. On Netbeans it happens when I right click on a site and select properties. Here's a link to a screen shot after I click on the preferences menu (I don't have enough points to post an image yet): http://www.jestep.com/images/screen-2.jpg. Note that the main workspace is grayed out. I have to hit Escape to close the hidden preferences window. I've tried unstinstalling, completely wiping the registry of any trace of the program and reinstalling. Thought it may have been a multi-monitor issue when I switched from 2 monitors down to 1, but menu's were not on other monitor when I plugged one back in. I've reset workspaces, windows display, windows performance settings, changed resolution, safe mode, everything I can think of. I cannot figure out what would cause the same problem on completely unrelated software, and I cannot reset it by reinstalling. Any help would be greatly appreciated.

  Read the article

• Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

  - by Kairan

  Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

  Read the article

• USB mouse disconnecting and reconnecting in windows and linux

  - by Kalak

  I have a problem similar to what is described at "Why is my USB mouse disconnecting and reconnecting randomly and often?" except is is happening in both Windows 7 and Linux (Ubuntu 12/04TLS, fully patched), multiple mice, multiple OSs. It stops responding to input for about 3-5 seconds, then starts responding again. It's more frequent and lasts longer when running games (TF2, L4D, Dishonored, Borderlands 2, and more), but happens when just running the OS as well. I was hoping it was the motherboard so I bought a USB 2.0 PCI card to try that, but it's still happening. I've stripped it down to just the keyboard and mouse (different keyboard too just in case the keyboard was the problem), but it's still happening. All the hardware (mice and keyboards) work fine on other computers. I have literally pulled the mouse and keyboard out and plugged them into another computer (laptop) and re-joined the online game and had no problem with the keyboard and mouse combo that just failed on my gaming rig. Please no driver / Windows or Linux only suggestions, as that wouldn't effect both OSs. edit: known good mice I've brought home are now going bad. I suspect the hardware is messed up (voltage?) and has been frying the mice.

  Read the article

• Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

  - by Bo102010

  (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

  Read the article

• Separate computers in my apartment can't communicate to each other?

  - by Razor Storm

  In my apartment, the management provides the building with a network connection. I have my computer plugged into the ethernet coming out of the walls, and my friend who also lives in the apartment building has his computer connected to a separate ethernet jack. As far as I know our two computers are not within a LAN, and ipconfig shows that we only have external ip addresses. The problem, then, appears when we attempt make direct communication between our computers. I have some hosting server set up on my machine, and my friend is unable to connect to it via my ip address. Other people who do not live in the apartment can connect fine. Ethernet adapter Local Area Connection: IPv4 Address. . . . . . . . . . . : 204.29.113.41 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 204.29.112.1 His ip: 204.29.113.104 Using a fulltunnel vpn doesn't help.

  Read the article

• Can't get .htaccess to work

  - by orokusaki

  I'm using Apache2 on Ubuntu Lucid Lynx. I have config set to use .htaccess like normal. This is my default site: <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride All Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride All Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> I've tried lower case "all" (AllowOverride all) as well. My .htaccess file looks like this: //Rewrite all requests to www Options +FollowSymLinks RewriteEngine on RewriteCond %{HTTP_HOST} ^mydomain.com [nc] RewriteRule ^(.*)$ http://www.mydomain.com/$1 [r=301,nc] //301 Redirect "old_junk.html" File to "new_junk.html" Redirect 301 /old_junk.html /new_junk.html //301 Redirect Entire Directory "old_junk/" to "new_junk/" RedirectMatch 301 /old_junk/(.*) /new_junk//$1 // Copy and paste redirect examples from above: (with mydomain replaced with my actual domain... and my computer is plugged in)

  Read the article

• ASUS EAH5450 Graphics Card (ATI Radeon HD5450 - 1 GB DDR3) on Windows 2003? Anybody got it to work?

  - by JJarava

  Hi all! I've just bought an ASUS EAH5450 Graphics Card (ATI Radeon HD5450, 1 GB DDR3) for my main system, but I haven't been able to make it work under Windows 2003 (my OS in that system). When I plugged the card, I got a couple of "installing drivers" prompt for things such as "ATI High Definition Audio Device" that got themselves sorted out of the Internet, and then a "Standard VGA Graphics Adapter". The CD that came with the card installs something called "ATI Catalyst Install Manager" and .net 2.0, but no drivers. I've downloaded the latest (WinXP 32bits) drivers from ATI, and the experience is the same: I don't get any drivers installed. My Motherboard is an ASUS A8N-SLI with nVidia nForce 4 chipset (for an Athlon 64X2, somewhat old), but my previous card was an ATi Radeon X700, so it's been working with ATI cards before. On POST, during boot I see a "Display Card" Device (Vendor ID 1002-68F9-0300) and a "Multimedia Device" (1002-AA68-0403), and when viewing the properties of the "Standard VGA", they match the device ID. Any hints? I'd really hate having to get rid of the card, and I'm sure it's not that strange what I'm trying to do...

  Read the article

• Windows 7 64bits installation via USB asks for drivers

  - by Shikiryu

  I just bought a new config ( ASUS p8z68-v lx, i5-2500k + ram and new graphic card ). Coming back and installing it in my old computer, I just saw that my DVD player was on IDE (yup…). So, I needed to install windows 7 64bits from my usb key. Fine, I made my usb key bootable and copy the official DVD on it (the same version that was on my old computer), set BIOS to boot on it first and started the computer up. It worked fine until it asks me for cd/dvd drivers (which is funny since, I do it via USB because I can't plug in my DVD player :D) I have 3 SATA HDD plugged in and that's it. I made a small google search and found that it could be SATA or RAID drivers. Fine, I took another USB KEY and put all my motherboard drivers on it (from the CD sold with the MB) and none of those drivers seemed to work. I tried downloading new drivers from ASUS website and same effect. Any idea but no "buy a new DVD player", I'm now broke for the month :) ?

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >