Search Results

Search found 4822 results on 193 pages for 'ram prasad'.

Page 42/193 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

• Weird screeching sounds coming from computer

  - by EGHDK

  My computer makes a high pitched whine noise that initially was coming from my SSD, but now I recently installed more ram into my laptop and it makes a new sounds. I don't want my ram or SSD to die on me. Are there any tests to test both of these? Again, these are really high pitched whine(y) sounds that you wouldn't hear normally, but when I'm home alone and it's silent, the noise sounds as loud as can be.

  Read the article

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• Easy Install Resets Hardware Settings

  - by bob5972

  I think there's a problem with the Easy Install setup. I selected "Installer disc image," and it came up and said that it would use "Easy Install," I think I hit next, and then I went back changed my mind, and selected "I will install the operating system later." After finishing the wizard, I think it still went and ran Easy Install, because it auto-installed VMware tools and I never got to select anything for my windows setup. Then, when it was finished, all the hardware changes I had made were lost. The RAM was changed from 2 GB back to the default of 1 GB, my CD ROM drive was set back to "Use a Physical Drive" and "Connect at Power On", and the Floppy Drive was also set to "Connect at Power On", after I disabled them. I was trying to install Windows 7, and I wasn't sure if I could change the RAM settings after installation without needing to reactivate it, so I deleted the VM and tried to start over. This time, the "Installer disc image" had my Win7 image pre-selected, so I clicked "I will install it myself later," set my hardware again, and tried to boot off my CD. Again,it did an Easy Install, and reset my RAM and my drive settings. So I deleted it again and the third time it still had the Win7 image pre-selected, but this time I unplugged all the drives and let it try to boot off the empty harddrive and fail, and made sure it kept all my hardware settings. Then, I powered it off, put my Win7 image in the guest CD ROM, and powered it on. This time it finally let me run the installer and pick my language, and type a user name. This time when I powered it off it kept my hardware settings. I can duplicate the error by doing exactly the steps above. Creating a new VM, selecting my "Installer Image," hitting next, going back, selecting "I will Install it myself," and then finish the wizard, and customizing my hardware right before the end, setting the CD Rom drive to the same installer media, and setting "Connect on Power On." (If I start it without the CD ROM in the first time, it doesn't do it). When I power on, I'm not prompted for any install information (like language and user name), and when it runs the first timemy hardware choices are reset (like the RAM back to 1 GB). If it helps, I'm running VMware Workstation 7.0.1 build-227600 on Gentoo Linux

  Read the article

• Is there a difference between the actual chip intended for Dual Channel vs Triple Channel

  - by JimDel

  Is there a difference between the actual chips intended for Dual Channel vs Triple Channel. I bought a set of triple channel memory but I'm only using 2 of the 3 chips. I'm getting the error "Display driver NVIDIA Windows Kernel Mode Driver, Version 197.45 stopped responding and has successfully recovered" There seems to be a TON of discussion on the web about this and some say it might be RAM related. This is the ram I'm using. Thanks

  Read the article

• Increase process memory cap.

  - by Janis Veinbergs

  Doing copy/paste in Visual Studio 2010 RTM on Windows 7, 3GB ram machine, I was unable to copy text because of an error: Task Manager shows that devenv.exe is using a little more than 500MB. However I still have almost 1GB of free RAM available. Is that somekind of memory cap? If so, is there a way to increase it? It may be a bug, but maybe there is a workaround?

  Read the article

• SQL Server 2012 Read-Only Replica physical requirements

  - by Ddono25

  We are going to be setting up two replicas of our DataMart and related databases, and our plan includes using Hyper-V VM's to handle the load. When creating the VM's, we cannot find specific requirements or recommendations for RAM/CPU power for read-only replicas. Our current Primary DataMart setup has 64GB RAM and Two Quad-Core procs, which so far has been adequate for our usage. What should be the server setup for replicas and SQL Server to adequately support the read-only usage?

  Read the article

• What causes Windows 8 Consumer Preview to lock-up / freeze / hang in Oracle VM VirtualBox?

  - by Zack Peterson

  I've installed Windows 8 Consumer Preview to a virtual machine using Oracle VM VirtualBox (4.1.14). It works well except for occasional temporary lock-up / freeze / hang interruptions. It will freeze for about a minute and then resume like normal for several more minutes before freezing again. Host Windows 7 Professional 64-bit 16 GB RAM Intel Core i7 (quad core, hyper threading, virtualization) CPU Guest Windows 8 Consumer Preview 64-bit 2 GB RAM 2 CPUs How should I configure VirtualBox to run Windows 8 well?

  Read the article

• How can Rackspace beat DigitalOcean's Pricepoint? [on hold]

  - by Matt Jensen

  I have recently discovered Digital Ocean and I have found it to be a relatively nice experience for small staging servers, and the thought occurred to me, why am I paying $267~ for a server on Rackspace (40GB RAM, 160 GB Drive, 2 vCPUs, 400 Mb/s) when Digital Ocean offers a server for $40 (40 GB RAM, 60GB Drive [storage is not a concern of mine], 2 vCPUs, ?Mb/s)? Does Rackspace offer some kind of obvious advantages in Transfer speed/bandwidth? My applications are small startups that for the immediate future will only have about 200-300 concurrent users at once.

  Read the article

• Real-time offline folder-to-folder backup application needed (Windows)

  - by niktech

  I recently started using Intel Matrix Storage RAID solution that allowed me to use my 5 1TB drives for two RAID volumes. First one a 1TB RAID 0 striped across all 5 drives and second one a RAID 5 across the rest of the free space on all drives (around 2.85TB usable space). The RAID 0 I use for OS, applications and games while the RAID 5 I use as a more-permanent type storage (photos, etc). Now I do realize that running the OS and applications on RAID 0 across 5 drives is very dangerous, which is what brings up the following question. Is there a reliable freeware realtime backup application that can backup a set of folders from one drive to another drive (no online backups needed)? I've already tried a few (Mozy, Yadis, Comodo Backup, GFI Backup, Idoo, Crash Plan) but none meet my requirements: Low CPU and RAM usage. Realtime Backups - as soon as a file is modified in the source folder, it is added to the backup queue which will be processed with the lowest priority when the CPU is idle. This backup queue should persist in cases of computer restarts (ie: the source and destination folders should always have the same set of files, except for the ones waiting in the backup queue). Incremental Backups - if only 10 bytes changed in a 1GB file, the app should only copy those 10 new bytes. Ability to back up locked and opened files (some apps, like Yadis, can't back up critical files like browser favorites). Ability to run as a service (no need for any user to log-in to have the app started). Optional requirements: Compression of the destination into a well-known format (RAR, Zip) that can be directly read without the use of the application. Preset source folders (such as Browser Favorites, Game Saves, Application Settings, etc). The idea is to use RAID 0 array as "semi-persistent RAM-like" storage which in case of a failure can be quickly rebuilt by reinstalling the OS, apps and games and copying over the settings, saves, favorites from the RAID 5. I'm also thinking of taking this RAID 0 as RAM idea to the extreme with SSDs (as soon as we get some nice 6Gb/s SATA III SSDs out there), where a couple of SSDs chained in RAID 0 will work as yet another semi-persistent cache layer sitting between the RAM and the HD. I'm just hoping there already exists an application that satisfies these requirements... otherwise I'll have to write one myself, which I would prefer not to do.

  Read the article

• Celery - minimize memory consuption

  - by Andrew

  We have ~300 celeryd processes running under Ubuntu 10.4 64-bit , in idle every process takes ~19mb RES, ~174mb VIRT, thus - it's around 6GB of RAM in idle for all processes. In active state - process takes up to 100mb of RES and ~300mb VIRT Every process uses minidom(xml files are < 500kb, simple structure) and urllib. Quetions is - how can we decrease RAM consuption - at least for idle workers, probably some celery or python options may help? How to determine which part takes most of memory?

  Read the article

• Is a 2006 Mac Mini's processor upgradeable to a Core 2 Duo?

  - by chiurox

  I have a Mac Mini with Core Solo 1.5GHz, 512mb RAM, 60gb HDD, etc... I know, it's very old but since it's lying around here, I wanted to bump it up for general usage and some experimental iPhone development. Also, Snow Leopard can't be installed as it doesn't have enough RAM. I browsed around but I'm not sure if this Mac Mini's motherboard accepts a Core2Duo (at least a 2.0GHz). If anyone could inform me which generation of Core2Duo it still accepts, I'd be grateful.

  Read the article

• Viewing the disk I/O in linux

  - by Muahmmad Zeeshan

  Hi, I want to know about how to view the disk I/O in linux so that i can check if i have to increase the ram. Also the limits/thresholds after which i should increase the ram. Thank You

  Read the article

• Cassandra on heterogeneous servers

  - by happy-coding

  I am currently running 4 cassandra nodes with the following hardware in a Apache Cassandra cluster: AMD Athlon 64 X2 6000+ 8G RAM 750G hard disk It shows not such a good writing performance and a really bad read performance with sometimes also timeouts. I was wondering if it makes sense to add 2 nodes with a different hardware (8 CPUs and more RAM) to improve this. Or does a cassandra cluster works best with the same hardware in every node? Thanks & best regards

  Read the article

• I have been told to accept one error with Memtest86+

  - by DustByte

  Bought a new computer back in August with 4x4 GB RAM. Had problems with the RAM. They sent me four new sticks, which also generated errors. Singled out four sticks (from the eight I now had) that didn't generate any errors. Discovered by coincident a new RAM error last week (this time no BSOD). Contacted the company. According to them there have been issues with a bad stock from last summer so I got two tested 8 GB sticks sent to me. Been running Memtest86+ over the weekend. After 20 hours I got an error (see attached photo). The test has now been running for 37 hours but so far only this one error. I contacted the company where I bought the computer. They wrote back: I wouldn't worry about hat one fail. We have had similar situations here whereby it passes numerous times but then fails once. We think it's an issue with memtest, after all memory is faulty or it isn't so you can't really have it pass a few times, fail the next time around and then pass again! Please trust me on this and continue with the memory we sent you and if your problems continue we'll look at getting it replaced again. I gather from other forum posts that many people do not accept a single error. What could this single error signify, faulty RAM or a glitch in the MEMTEST program (or other)? Update: From the helpful comments below I conclude that an occasional (and rare) "random" error could occur and be acceptable, but repeated errors at the same address would indicate malfunction. Memtest has now run for 45 hours and I still have only one error. For everyone's information, I will keep running the test. In less than two days I am going away for a month. I will most likely leave Memtest running. As I do not have a UPS there is a risk that a power outage will ruin the experiment. The computer is a desktop so I cannot bring it with me (which would curiously have exposed it to more cosmic rays as I will be flying ;)).

  Read the article

• Is a 2006 Mac Mini’s processor upgradeable to a Core 2 Duo?

  - by chiurox

  I have a Mac Mini with Core Solo 1.5GHz, 512mb RAM, 60gb HDD, etc... I know, it's very old but since it's lying around here, I wanted to bump it up for general usage and some experimental iPhone development. Also, Snow Leopard can't be installed as it doesn't have enough RAM. I browsed around but I'm not sure if this Mac Mini's motherboard accepts a Core2Duo (at least a 2.0GHz). If anyone could inform me which generation of Core2Duo it still accepts, I'd be grateful.

  Read the article

• Sleep uses more power than I expect

  - by Niklas

  When my new Dell laptop with Windows 7 Home Premium and 4GB RAM sleeps (not when it hibernates), it will drain the battery overnight. My old Dell laptop with XP Pro (2 GB RAM) could sleep for days without running out of battery. Is it normal that Windows 7 sleep is this power-hungry or should I troubleshoot my new machine? Edit: I know how to set the different sleep/hibernate settings. That is not what I'm asking.

  Read the article

• Is the following combination of components valid to function as a desktop computer? [closed]

  - by Gideon Potgieter

  Could someone with more PC building experience than me tell me whether these PC components can cooperate fully as a self-made PC? Processor: Intel Core i5-3570K Video card: Asus Radeon HD 7870 Motherboard: Gigabyte GA-Z77-D3H RAM: Corsair CMZ16GX3M2A1600C10 Vengeance 16GB 1600MHz CL10 DDR3 (x2) Storage: Western Digital WD1002FAEX (x2) Display: Samsung S24B300HL Sound: Logitech X140 Chassis: Thermaltake V4 Black Edition VM30001W2Z Power supply: Seagate OEM 500W Builder PSU Optical drive: Asus DRW-24B1ST Thanks in advance! (btw, I know 32 GB RAM is unnecessary, but I want to buy it to use as a reserve)

  Read the article

• Low FPS in some games, but hardware not fully used

  - by Mario De Schaepmeester

  I just did a little funny experiment in the game/sim "Train Simulator 2013". I normally have good FPS in it (around 30) at full settings. What I did was make a really, really long train so that the calculations the sim needed to make were enormous (the sim is quite realistic, it takes all things into account like speed/acceleration, G-forces, comfort levels, possible wheel slip and many more, and most of those things on each carriage seperately). This resulted in only 14FPS as reported by the game, but it felt more like 8FPS or so. I have a Logitech G15 keyboard which has an LCD, and it allows me to monitor CPU/RAM and video card load on it. The strange thing is, all CPU cores were busy, but the total load was only about 60% maximum at all times. The video card was only on 30% load (possibly an important note, the memory was full, which is however not unusual for the game in question). The RAM had plenty of room and there weren't many operations as it didn't grow or shrink much. I just have the feeling that the game would run smoother if it used more of my hardware power. Why is it not doing so? I had the same in another game, The Elder Scrolls: Morrowind when using more than 100 mods (that all use scripting) and a few high res texture mods, + a full-on graphics improvement program. The engine is very old (2003), and so I thought this might be the cause (not being optimised for multithreading). I had thought of possible causes, like: The operating system doesn't let the games use all the resources. It doesn't make use of multi-threading appropriately. To eliminate the former, I tried a CPU stress tool and that got 100% CPU juice as I let it run, so the OS is not the problem. I gave its thread the "higher" priority though. My actual question In both games, I did things the engine was not really built to do or support. Can those games' framerate be limited cause of their own engine not being able to cope? What is the real reason and more importantly, can I help it? And in any case, could something actually be wrong with my hardware? It's all reasonably new, a couple of months, and I (almost) never experience any other trouble. Modern and much more demanding games work absolutely fine. Specs CPU: AMD Phenom II 965 X4 @ 3.4gHz RAM: 8GB of DDR3 RAM Video: MSI GTX560 (nVidia chip) with 1GB of GDDR5 memory OS: Windows 7 Ultimate 64 bit Nothing overclocked.

  Read the article

• Anyone tried boosting Windows performance by putting Swap File on a Flash drive?

  - by Clay Nichols

  Windows Vista introduced ReadyBoost which lets you use a Flash drive as a third (after RAM and HD) type of memory. It occurred to me that I could boost peformance on an old PC here w/ Win XP (32 bit, max'd at 4GB RAM) by putting it's swap file (page file) on a flash drive. (Now, before anyone comments: apparently Flash drives (10-30MB/s transfer rates) are slower than HDD (100+ MB/s) (I'm asking that as a separate question on this forum).

  Read the article

• How to find the process(es) which are hogging the machine

  - by Aaron Digulla

  Scenario: All of a sudden, my computer feels sluggish. Mouse moves but windows take ages to open, etc. uptime says the load is 7.69 and raising. What is the fastest way to find out which process(es) are the cause of the load? Now, "top" and similar tools isn't the answer because they either show CPU or memory usage but not both at the same time. What I need is the single command which I might be able to type as it happens - something that will figure out any of System is trying to swap 8GB of RAM to disk because process X ... or process X seeks all over the disk or process X uses 400% CPU" So what I'm looking for is iostat, htop/atop and similar tools run into one with an output like this: 1235 cp - Disk trashing 87 chrome - Uses 2&nbsp;GB of RAM 137 nfs_bench - Uses 95% of the network bandwidth I don't want a tool that gives me some numbers which I can analyze but a tool that tells me exactly which process causes the current load. Assume that the user in front of the keyboard barely knows how to write "process", but the user is quickly overwhelmed when it comes to "resident size", "virtual memory" or "process life cycle". My argument goes like this: A user notices a problem. There can be thousands of reasons ... well, almost :-) The user wants to know the source of the problem. The current solutions give me lots of numbers, and I need to know what these numbers mean. What I'm looking for is a meta tool. 99% of the data is irrelevant to the problem. So what the tool should do is look for processes which hog some resource and list only those along with "this process needs a lot of CPU, this produces many IRQs, this process allocates a lot of RAM (and it's still growing)". This will be a relatively short list. It will be much more simple for someone new to this to locate the culprit from this list than from the output of, say, htop which gives me about 5000 numbers but requires me to fold multi-threaded processes myself (I have 50 lines which say VIRT 2750M but only 16 GB of RAM - the machine ought to swap itself to death but of course, this is a misinterpretation of the data that can happen quickly).

  Read the article

• What does CPU Time consist of?

  - by Sid

  What does CPU time exactly consist of? For instance, is the time taken to access a page from the RAM (at which point, the CPU is most likely idling) part of the CPU time? I'm not talking about fetching the page from the disk here, just fetching it from the RAM. Thanks

  Read the article

• On ubuntu 10.04, what is the recommended RoR stack?

  - by Kurucu

  I can't find clear answers / methods on this. As seen elsewhere, passenger and RoR under apache gobble up ram on my VPS. I've tried a multitude of stacks and implementations, currently resting on a sub optimal apache/cgi/rails configuration, which has swapped my ram usage for CPU time and slow response to requests. Can anyone recommend an efficient and preferably simple to administer method of setting up rails apps in ubuntu 10.04 server?

  Read the article

• Virtual Memory and SSD

  - by Zombian

  While studying for the A+ Exam I was reading about SSD's and I thought to myself that if you had a mobo with a low RAM limit you could use a dedicated SSD purely for Virtual RAM. I looked up some info on line and the info I found said that this was a poor practice but didn't explain why. Why shouldn't SSD's be used for Virtual Memory and what are your thoughts on a dedicated Virtual Memory drive? Thank you!

  Read the article

• SQL Express 2008 R2 on Amazon EC2 instance: tons of free memory, poor performance

  - by gravyface

  The old SQL Express 2005 was running on a low-end single Xeon CPU Dell server, RAID 5 7200 disks, 2 GB RAM (SBS 2003). I have not done any baseline measurements on the old physical server, but the Web app is used by half a dozen people (maybe 2 concurrently), so I figured "how bad can an Amazon EC2 instance be?". It's pretty horrible: a difference of 8 seconds of load time on one screen. First of all, I'm not a SQL guru, but here's what I've tried: Had a Small Instance, now running a c1.medium (High Cpu Medium) Windows 2008 32-bit R2 EBS-backed instance running IIS 7.5 and SQL Express 2008 R2. No noticeable improvement. Changed Page File from fixed 256 to Automatic. Setup a Striped Mirror from within Disk Management with two attached 1 GB EBS volumes. Moved database and transaction log, left everything else on the boot EBS volume. No noticeable change. Looked at memory, ~1000 MB of physical memory free (1.7 GB total). Changed SQL instance to use a minimum of 1024 RAM; restarted server, no change in memory usage. SQL still only using ~28MB of RAM(!). So I'm thinking: this database is tiny (28MB), why isn't the whole thing cached in RAM? Surely that would speed up performance. The transaction log is 241 MB. Seems kind of large in comparison -- has this not been committed? Is it a cause of performance degradation? I recall something about Recovery Models and log sizes somewhere in my travels, but not positive. Another thing: the old server was running SQL Express 2005. Not sure if that has any impact, but I tried changing the compatibility level from SQL 2000 to 2008, but that had no effect. Anyways, what else can I try here? Seems ridiculous to throw more virtual hardware at this thing. I know I/O is going to be rough on EBS volumes, but surely others are successfully running small .NET/SQL apps on reasonably priced instances?

  Read the article

• How many Tomcat instances can one application server handle?

  - by NetworkUser

  My network engineer states I am part of a cluster where two apache application servers(512G RAM each) have 142 instances each of Tomcat (of which my company represents 6 each with 2G RAM). This seems like a lot and my latency issues move with the hour of the day - 7AM CST software functions fine, 10AM CST - system slows significantly this slowness continues until 6PM CST. My question is how many Tomcat instances can one application server handle?

  Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >