Search Results

Search found 4822 results on 193 pages for 'ram prasad'.

Page 43/193 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

• Server purchase advice AMD Opteron

  - by maruti

  Dell PE2970 with AMD Opteron 6core 2431 2.4GHz + 64GB 667Mhz RAM - 2435 is not available with Dell now Dell R905 with AMD Opteron 8435 2.6 GHz + 64GB 800Mhz RAM - but this CPU is 4-8 way, I have chosen only 2P config Both are very close on price and I am leaning towards the R905, please advise.

  Read the article

• Debian Squeeze and available memory (1GB absent)

  - by user66279

  Hi, here I've a dedicated server with 12GB RAM and running Debian Lenny x64. dmesg | grep Memory [ 0.004000] Memory: 11917152k/12259740k available (2279k kernel code, 333820k reserved, 1022k data, 216k init) Since some days, I've another dedicated server (nearly same hardware), but with Debian Squeeze x64 (installed via debootstrap, Kernel 2.6.32-5-xen-amd64) dmesg | grep Memory [ 1.551510] Memory: 6864620k/8151916k available (3146k kernel code, 1057736k absent, 229560k reserved, 1901k data, 600k init) what does absent memory mean? And how can I get 1GB of RAM back?

  Read the article

• Output of free -m on a Linux server

  - by cat pants

  I can see from this page here: http://www.linuxatemyram.com/ That the correct amount of free ram is on the "-/+ buffers/cache" line. The extra ram being used is for disk caching. However, I noticed that the total amount of memory used listed in "-/+ buffers/cache" line is significantly less than the sum total of the "RES" column of the processes shown in top. And AFAIK, the "RES" column is how much physical memory is being used by a process. How do you explain this discrepancy?

  Read the article

• windows-7 x86 to x64 upgrade

  - by small_potato

  is it possible to update my system from windows 7 x86 to x64 without losing data ? cpu architecture is 32bit but I have 4g ram, so to unseal the ram, I have to go with x64.

  Read the article

• How does the linux kernel manage less than 1GB physical memory ?

  - by TheLoneJoker

  I'm learning the linux kernel internals and while reading "Understanding Linux Kernel", quite a few memory related questions struck me. One of them is, how the Linux kernel handles the memory mapping if the physical memory of say only 512 MB is installed on my system. As I read, kernel maps 0(or 16) MB-896MB physical RAM into 0xC0000000 linear address and can directly address it. So, in the above described case where I only have 512 MB: How can the kernel map 896 MB from only 512 MB ? What about user mode processes in this situation? Where are user mode processes in phys RAM? Every article explains only the situation, when you've installed 4 GB of memory and the kernel maps the 1 GB into kernel space and user processes uses the remaining amount of RAM. I would appreciate any help in improving my understanding. Thanks..!

  Read the article

• image archive VS image strip

  - by DevA

  Hi, i've noticed that plenty of games / applications (very common on mobile builds) pack numerous images into an image strip. I figured that the advantages in this are making the program more tidy (file system - wise) and reducing (un)installation time. During the runtime of the application, the entire image strip is allocated and copied from FS to RAM. On the contrary, images can be stored in an image archive and unpacked during runtime to a number of image structures in RAM. The way I see it, the image strip approach is less efficient because of worse caching performance and because that even if the optimal rectangle packing algorithm is used, there will be empty spaces between the stored images in the strip, causing a waste of RAM. What are the advantages in using an image strip over using an image archive file?

  Read the article

• memory available to 64bit Fedora guest under 32bit XP host running virtualbox

  - by Chris Card

  I have successfully installed a 64 bit Fedora 11 guest os using VirtualBox on a host machine (AMD64) running 32 bit Windows XP . At the moment the host machine has 2 Gb ram installed and I've allocated 1 Gb to the guest, which all works well. The host machine can hold a maximum of 4 Gb ram, so I was wondering if it's worth buying an extra 2 Gb for it. I know that 32 bit Windows XP can't use all of the 4 Gb, but can the guest os use any of the ram that the host os can't use?

  Read the article

• XmlDocument caching memory usage

  - by mdsharpe

  We are seeing very high memory usage in .NET web applications which use XmlDocument. A small (~5MB) XML document is loaded into an XmlDocument object and stored in HttpContext.Cache for easy querying and XSLT transformation on each page load. The XML is modified on disk periodically so a cache has a dependency on the file. Such an application appears to be using hundreds of megabytes of RAM. I have experimented with requesting garbage collection on each request start, and this keeps the RAM usage far lower but I cannot imagine this is good practise. Does anyone have any suggestions as to how we can achieve the same goal but with lower RAM usage?

  Read the article

• Issues with SharePoint 2010 Development

  - by Rahul Soni

  I am planning to use my laptop for SharePoint 2010 development and I have only 4 GB RAM which is not even upgradable. Just because of RAM constraint, my VS 2010 keeps crawling if I try to run it along with SharePoint 2010 on the same machine. Hence, I've reformatted my machine and looking for alternate solutions until I get a new laptop. Currently, I have installed VS 2010 ONLY on my laptop and wanted to create an empty SharePoint project. Once done with my project, I want to deploy it on a different machine (which is a 4GB RAM machine as well, but contains only SharePoint 2010). I thought this will work and give me a bit of breather if everything is configured well. Unfortunately, when I tried creating a new SharePoint Empty Project in VS 2010, it says... A SharePoint server is not installed on this computer. A SharePoint server must be installed to work with SharePoint projects. Is there a way out?

  Read the article

• Somewhat newb question about assy and the heap.

  - by Eric M

  Ultimately I am just trying to figure out how to dynamically allocate heap memory from within assembly. If I call Linux sbrk() from assembly code, can I use the address returned as I would use an address of a statically (ie in the .data section of my program listing) declared chunk of memory? I know Linux uses the hardware MMU if present, so I am not sure if what sbrk returns is a 'raw' pointer to real RAM, or is it a cooked pointer to RAM that may be modified by Linux's VM system? I read this: How are sbrk/brk implemented in Linux?. I suspect I can not use the return value from sbrk() without worry: the MMU fault on access-non-allocated-address must cause the VM to alter the real location in RAM being addressed. Thus assy, not linked against libc or what-have-you, would not know the address has changed. Does this make sense, or am I out to lunch?

  Read the article

• how to split string with some seperator but without removing that seperator in Java?

  - by sag

  Hi, I m facing problem in splitting string. Actually i want to split a string with some seperator but without loosing that seperator. when we use somestring.split(String seperator) method in java it splits the string but removes the seperator part from string.It should not happen. I want result like below: Example::string1="Ram-sita-laxman"; seperator="-"; string1.split(seperator); output : [Ram, sita, laxman] but i want the result like :[Ram, -sita, -laxman] is there a way to get output like this?

  Read the article

• message queue : selection and sizing

  - by user238591

  Hi, I have 20 messages/s, each 1 - 1.5 Mbytes. I need High Availability (2 to 4 servers min). I need low latencey (high daily volume - full RAM prefered). I need persistent poisoned messages queue. Only few clients (about 16), locally. I can have 12-16G bytes RAM per server (brooker). Which JMS message queue / messaging would you recommend ? On what configuration (CPU/RAM) ? Can I propose optionnal NAS persistence (in case of final delivery failure) ? Thanks

  Read the article

• How to transfer large file (File size > Heap Size) over the network?

  - by neo

  How to transfer large file (File size Heap/RAM Size) over the network ? Lets say I have file (size 10GB) I want to transfer it machine a (RAM 512mb) to machine b (RAM 512mb). Want achieve this using java code. First, is it possible ? Any recommendation on framework. If possible, can we speed this up using threading ? Important criteria: file's data sequence needs to be maintained during transfer. Any example will be great help.

  Read the article

• Firefox consumes too much memory

  - by Vivek

  I have firefox version 11.0 and am running ubuntu 11.10. Firefox takes upto 850MB RAM with only six or seven tabs opened and all the tabs loaded with light weight websites only. I wonder why would a browser consume so much memory. It keeps increasing its memory consumption over time. I have 3GB RAM and most of the times firefox consumes upto 30% of my memory. How do I fix this? EDIT: The output of the command sudo iotop -oPa as asked by @Jippie

  Read the article

• Juju Zookeeper & Provisioning Agent Not Deployed

  - by Keith Tobin

  I am using juju with the openstack provider, i expected that when i bootstrap that zookeeper and provisioning agent would get deployed on the bootstrap vm in openstack. This dose not seem to be the case. the bootstrap vm gets deployed but it seems that nothing gets deployed to the VM. See logs below, I may be missing something, also how is it possible to log on the bootstrap vm. Could I manual deploy, if so what do I need to do. Juju Bootstrap commend root@cinder01:/home/cinder# juju -v bootstrap 2012-10-12 03:21:20,976 DEBUG Initializing juju bootstrap runtime 2012-10-12 03:21:20,982 WARNING Verification of xxxxS certificates is disabled for this environment. Set 'ssl-hostname-verification' to ensure secure communication. 2012-10-12 03:21:20,982 DEBUG openstack: using auth-mode 'userpass' with xxxx:xxxxxx.10:35357/v2.0/ 2012-10-12 03:21:21,064 DEBUG openstack: authenticated til u'2012-10-13T08:21:13Z' 2012-10-12 03:21:21,064 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors' 2012-10-12 03:21:21,091 DEBUG openstack: 200 '{"flavors": [{"id": "3", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/3", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/3", "rel": "bookmark"}], "name": "m1.medium"}, {"id": "4", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/4", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/4", "rel": "bookmark"}], "name": "m1.large"}, {"id": "1", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "bookmark"}], "name": "m1.tiny"}, {"id": "5", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/5", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/5", "rel": "bookmark"}], "name": "m1.xlarge"}, {"id": "2", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/2", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/2", "rel": "bookmark"}], "name": "m1.small"}]}' 2012-10-12 03:21:21,091 INFO Bootstrapping environment 'openstack' (origin: ppa type: openstack)... 2012-10-12 03:21:21,091 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state 2012-10-12 03:21:21,092 DEBUG openstack: GET 'xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state' 2012-10-12 03:21:21,165 DEBUG openstack: 200 '{}\n' 2012-10-12 03:21:21,165 DEBUG Verifying writable storage 2012-10-12 03:21:21,165 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/bootstrap-verify 2012-10-12 03:21:21,166 DEBUG openstack: PUT 'xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/bootstrap-verify' 2012-10-12 03:21:21,251 DEBUG openstack: 201 '201 Created\n\n\n\n ' 2012-10-12 03:21:21,251 DEBUG Launching juju bootstrap instance. 2012-10-12 03:21:21,271 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/juju_master_id 2012-10-12 03:21:21,273 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-groups 2012-10-12 03:21:21,273 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-groups' 2012-10-12 03:21:21,321 DEBUG openstack: 200 '{"security_groups": [{"rules": [{"from_port": -1, "group": {}, "ip_protocol": "icmp", "to_port": -1, "parent_group_id": 1, "ip_range": {"cidr": "0.0.0.0/0"}, "id": 7}, {"from_port": 22, "group": {}, "ip_protocol": "tcp", "to_port": 22, "parent_group_id": 1, "ip_range": {"cidr": "0.0.0.0/0"}, "id": 38}], "tenant_id": "d5f52673953f49e595279e89ddde979d", "id": 1, "name": "default", "description": "default"}]}' 2012-10-12 03:21:21,322 DEBUG Creating juju security group juju-openstack 2012-10-12 03:21:21,322 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-groups' 2012-10-12 03:21:21,401 DEBUG openstack: 200 '{"security_group": {"rules": [], "tenant_id": "d5f52673953f49e595279e89ddde979d", "id": 48, "name": "juju-openstack", "description": "juju group for openstack"}}' 2012-10-12 03:21:21,401 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-group-rules' 2012-10-12 03:21:21,504 DEBUG openstack: 200 '{"security_group_rule": {"from_port": 22, "group": {}, "ip_protocol": "tcp", "to_port": 22, "parent_group_id": 48, "ip_range": {"cidr": "0.0.0.0/0"}, "id": 54}}' 2012-10-12 03:21:21,504 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-group-rules' 2012-10-12 03:21:21,647 DEBUG openstack: 200 '{"security_group_rule": {"from_port": 1, "group": {"tenant_id": "d5f52673953f49e595279e89ddde979d", "name": "juju-openstack"}, "ip_protocol": "tcp", "to_port": 65535, "parent_group_id": 48, "ip_range": {}, "id": 55}}' 2012-10-12 03:21:21,647 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-group-rules' 2012-10-12 03:21:21,791 DEBUG openstack: 200 '{"security_group_rule": {"from_port": 1, "group": {"tenant_id": "d5f52673953f49e595279e89ddde979d", "name": "juju-openstack"}, "ip_protocol": "udp", "to_port": 65535, "parent_group_id": 48, "ip_range": {}, "id": 56}}' 2012-10-12 03:21:21,792 DEBUG Creating machine security group juju-openstack-0 2012-10-12 03:21:21,792 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-security-groups' 2012-10-12 03:21:21,871 DEBUG openstack: 200 '{"security_group": {"rules": [], "tenant_id": "d5f52673953f49e595279e89ddde979d", "id": 49, "name": "juju-openstack-0", "description": "juju group for openstack machine 0"}}' 2012-10-12 03:21:21,871 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/detail 2012-10-12 03:21:21,871 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/detail' 2012-10-12 03:21:21,906 DEBUG openstack: 200 '{"flavors": [{"vcpus": 2, "disk": 10, "name": "m1.medium", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/3", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/3", "rel": "bookmark"}], "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 40, "ram": 4096, "id": "3", "swap": ""}, {"vcpus": 4, "disk": 10, "name": "m1.large", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/4", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/4", "rel": "bookmark"}], "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 80, "ram": 8192, "id": "4", "swap": ""}, {"vcpus": 1, "disk": 0, "name": "m1.tiny", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "bookmark"}], "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 0, "ram": 512, "id": "1", "swap": ""}, {"vcpus": 8, "disk": 10, "name": "m1.xlarge", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/5", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/5", "rel": "bookmark"}], "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 160, "ram": 16384, "id": "5", "swap": ""}, {"vcpus": 1, "disk": 10, "name": "m1.small", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/flavors/2", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/2", "rel": "bookmark"}], "rxtx_factor": 1.0, "OS-FLV-EXT-DATA:ephemeral": 20, "ram": 2048, "id": "2", "swap": ""}]}' 2012-10-12 03:21:21,907 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers 2012-10-12 03:21:21,907 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers' 2012-10-12 03:21:22,284 DEBUG openstack: 202 '{"server": {"OS-DCF:diskConfig": "MANUAL", "id": "a598b402-8678-4447-baeb-59255409a023", "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "bookmark"}], "adminPass": "SuFp48cZzdo4"}}' 2012-10-12 03:21:22,284 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/juju_master_id 2012-10-12 03:21:22,285 DEBUG openstack: PUT 'xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/juju_master_id' 2012-10-12 03:21:22,375 DEBUG openstack: 201 '201 Created\n\n\n\n ' 2012-10-12 03:21:27,379 DEBUG Waited for 5 seconds for networking on server u'a598b402-8678-4447-baeb-59255409a023' 2012-10-12 03:21:27,380 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023 2012-10-12 03:21:27,380 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023' 2012-10-12 03:21:27,556 DEBUG openstack: 200 '{"server": {"OS-EXT-STS:task_state": "networking", "addresses": {"private": [{"version": 4, "addr": "10.0.0.8"}]}, "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "bookmark"}], "image": {"id": "5bf60467-0136-4471-9818-e13ade75a0a1", "links": [{"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/images/5bf60467-0136-4471-9818-e13ade75a0a1", "rel": "bookmark"}]}, "OS-EXT-STS:vm_state": "building", "OS-EXT-SRV-ATTR:instance_name": "instance-00000060", "flavor": {"id": "1", "links": [{"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "bookmark"}]}, "id": "a598b402-8678-4447-baeb-59255409a023", "user_id": "01610f73d0fb4922aefff09f2627e50c", "OS-DCF:diskConfig": "MANUAL", "accessIPv4": "", "accessIPv6": "", "progress": 0, "OS-EXT-STS:power_state": 0, "config_drive": "", "status": "BUILD", "updated": "2012-10-12T08:21:23Z", "hostId": "1cdb25708fb8e464d83a69fe4a024dcd5a80baf24a82ec28f9d9f866", "OS-EXT-SRV-ATTR:host": "nova01", "key_name": "", "OS-EXT-SRV-ATTR:hypervisor_hostname": null, "name": "juju openstack instance 0", "created": "2012-10-12T08:21:22Z", "tenant_id": "d5f52673953f49e595279e89ddde979d", "metadata": {}}}' 00000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 2012-10-12 03:21:27,557 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-floating-ips 2012-10-12 03:21:27,557 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/os-floating-ips' 2012-10-12 03:21:27,815 DEBUG openstack: 200 '{"floating_ips": [{"instance_id": "a0e0df11-91c0-4801-95b3-62d910d729e9", "ip": "xxxx.35", "fixed_ip": "10.0.0.5", "id": 447, "pool": "nova"}, {"instance_id": "b84f1a42-7192-415e-8650-ebb1aa56e97f", "ip": "xxxx.36", "fixed_ip": "10.0.0.6", "id": 448, "pool": "nova"}, {"instance_id": null, "ip": "xxxx.37", "fixed_ip": null, "id": 449, "pool": "nova"}, {"instance_id": null, "ip": "xxxx.38", "fixed_ip": null, "id": 450, "pool": "nova"}, {"instance_id": null, "ip": "xxxx.39", "fixed_ip": null, "id": 451, "pool": "nova"}, {"instance_id": null, "ip": "xxxx.40", "fixed_ip": null, "id": 452, "pool": "nova"}, {"instance_id": null, "ip": "xxxx.41", "fixed_ip": null, "id": 453, "pool": "nova"}]}' 2012-10-12 03:21:27,815 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023/action 2012-10-12 03:21:27,816 DEBUG openstack: POST 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023/action' 2012-10-12 03:21:28,356 DEBUG openstack: 202 '' 2012-10-12 03:21:28,356 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state 2012-10-12 03:21:28,357 DEBUG openstack: PUT 'xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state' 2012-10-12 03:21:28,446 DEBUG openstack: 201 '201 Created\n\n\n\n ' 2012-10-12 03:21:28,446 INFO 'bootstrap' command finished successfully Juju Status Command root@cinder01:/home/cinder# juju -v status 2012-10-12 03:23:28,314 DEBUG Initializing juju status runtime 2012-10-12 03:23:28,320 WARNING Verification of xxxxS certificates is disabled for this environment. Set 'ssl-hostname-verification' to ensure secure communication. 2012-10-12 03:23:28,320 DEBUG openstack: using auth-mode 'userpass' with xxxx:xxxxxx.10:35357/v2.0/ 2012-10-12 03:23:28,320 INFO Connecting to environment... 2012-10-12 03:23:28,403 DEBUG openstack: authenticated til u'2012-10-13T08:23:20Z' 2012-10-12 03:23:28,403 DEBUG access object-store @ xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state 2012-10-12 03:23:28,403 DEBUG openstack: GET 'xxxx:xx10.49.113.11:8080/v1/AUTH_d5f52673953f49e595279e89ddde979d/juju-hpc-az1-cb/provider-state' 2012-10-12 03:23:35,480 DEBUG openstack: 200 'zookeeper-instances: [a598b402-8678-4447-baeb-59255409a023]\n' 2012-10-12 03:23:35,480 DEBUG access compute @ xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023 2012-10-12 03:23:35,480 DEBUG openstack: GET 'xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023' 2012-10-12 03:23:35,662 DEBUG openstack: 200 '{"server": {"OS-EXT-STS:task_state": null, "addresses": {"private": [{"version": 4, "addr": "10.0.0.8"}, {"version": 4, "addr": "xxxx.37"}]}, "links": [{"href": "xxxx:xxxxxx.15:8774/v1.1/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "self"}, {"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/servers/a598b402-8678-4447-baeb-59255409a023", "rel": "bookmark"}], "image": {"id": "5bf60467-0136-4471-9818-e13ade75a0a1", "links": [{"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/images/5bf60467-0136-4471-9818-e13ade75a0a1", "rel": "bookmark"}]}, "OS-EXT-STS:vm_state": "active", "OS-EXT-SRV-ATTR:instance_name": "instance-00000060", "flavor": {"id": "1", "links": [{"href": "xxxx:xxxxxx.15:8774/d5f52673953f49e595279e89ddde979d/flavors/1", "rel": "bookmark"}]}, "id": "a598b402-8678-4447-baeb-59255409a023", "user_id": "01610f73d0fb4922aefff09f2627e50c", "OS-DCF:diskConfig": "MANUAL", "accessIPv4": "", "accessIPv6": "", "progress": 0, "OS-EXT-STS:power_state": 1, "config_drive": "", "status": "ACTIVE", "updated": "2012-10-12T08:21:40Z", "hostId": "1cdb25708fb8e464d83a69fe4a024dcd5a80baf24a82ec28f9d9f866", "OS-EXT-SRV-ATTR:host": "nova01", "key_name": "", "OS-EXT-SRV-ATTR:hypervisor_hostname": null, "name": "juju openstack instance 0", "created": "2012-10-12T08:21:22Z", "tenant_id": "d5f52673953f49e595279e89ddde979d", "metadata": {}}}' 2012-10-12 03:23:35,663 DEBUG Connecting to environment using xxxx.37... 2012-10-12 03:23:35,663 DEBUG Spawning SSH process with remote_user="ubuntu" remote_host="xxxx.37" remote_port="2181" local_port="45859". 2012-10-12 03:23:36,173:4355(0x7fd581973700):ZOO_INFO@log_env@658: Client environment:zookeeper.version=zookeeper C client 3.3.5 2012-10-12 03:23:36,173:4355(0x7fd581973700):ZOO_INFO@log_env@662: Client environment:host.name=cinder01 2012-10-12 03:23:36,174:4355(0x7fd581973700):ZOO_INFO@log_env@669: Client environment:os.name=Linux 2012-10-12 03:23:36,174:4355(0x7fd581973700):ZOO_INFO@log_env@670: Client environment:os.arch=3.2.0-23-generic 2012-10-12 03:23:36,174:4355(0x7fd581973700):ZOO_INFO@log_env@671: Client environment:os.version=#36-Ubuntu SMP Tue Apr 10 20:39:51 UTC 2012 2012-10-12 03:23:36,174:4355(0x7fd581973700):ZOO_INFO@log_env@679: Client environment:user.name=cinder 2012-10-12 03:23:36,174:4355(0x7fd581973700):ZOO_INFO@log_env@687: Client environment:user.home=/root 2012-10-12 03:23:36,175:4355(0x7fd581973700):ZOO_INFO@log_env@699: Client environment:user.dir=/home/cinder 2012-10-12 03:23:36,175:4355(0x7fd581973700):ZOO_INFO@zookeeper_init@727: Initiating client connection, host=localhost:45859 sessionTimeout=10000 watcher=0x7fd57f9146b0 sessionId=0 sessionPasswd= context=0x2c1dab0 flags=0 2012-10-12 03:23:36,175:4355(0x7fd577fff700):ZOO_ERROR@handle_socket_error_msg@1579: Socket [127.0.0.1:45859] zk retcode=-4, errno=111(Connection refused): server refused to accept the client 2012-10-12 03:23:39,512:4355(0x7fd577fff700):ZOO_ERROR@handle_socket_error_msg@1579: Socket [127.0.0.1:45859] zk retcode=-4, errno=111(Connection refused): server refused to accept the client 2012-10-12 03:23:42,848:4355(0x7fd577fff700):ZOO_ERROR@handle_socket_error_msg@1579: Socket [127.0.0.1:45859] zk retcode=-4, errno=111(Connection refused): server refused to accept the client ^Croot@cinder01:/home/cinder#

  Read the article

• Mysql performance problem & Failed DIMM

  - by murdoch

  Hi I have a dedicated mysql database server which has been having some performance problems recently, under normal load the server will be running fine, then suddenly out of the blue the performance will fall off a cliff. The server isn't using the swap file and there is 12GB of RAM in the server, more than enough for its needs. After contacting my hosting comapnies support they have discovered that there is a failed 2GB DIMM in the server and have scheduled to replace it tomorow morning. My question is could a failed DIMM result in the performance problems I am seeing or is this just coincidence? My worry is that they will replace the ram tomorrow but the problems will persist and I will still be lost of explanations so I am just trying to think ahead. The reason I ask is that there is plenty of RAM in the server, more than required and simply missing 2GB should be a problem, so if this failed DIMM is causing these performance problems then the OS must be trying to access the failed DIMM and slowing down as a result. Does that sound like a credible explanation? This is what DELLs omreport program says about the RAM, notice one dimm is "Critical" Memory Information Health : Critical Memory Operating Mode Fail Over State : Inactive Memory Operating Mode Configuration : Optimizer Attributes of Memory Array(s) Attributes : Location Memory Array 1 : System Board or Motherboard Attributes : Use Memory Array 1 : System Memory Attributes : Installed Capacity Memory Array 1 : 12288 MB Attributes : Maximum Capacity Memory Array 1 : 196608 MB Attributes : Slots Available Memory Array 1 : 18 Attributes : Slots Used Memory Array 1 : 6 Attributes : ECC Type Memory Array 1 : Multibit ECC Total of Memory Array(s) Attributes : Total Installed Capacity Value : 12288 MB Attributes : Total Installed Capacity Available to the OS Value : 12004 MB Attributes : Total Maximum Capacity Value : 196608 MB Details of Memory Array 1 Index : 0 Status : Ok Connector Name : DIMM_A1 Type : DDR3-Registered Size : 2048 MB Index : 1 Status : Ok Connector Name : DIMM_A2 Type : DDR3-Registered Size : 2048 MB Index : 2 Status : Ok Connector Name : DIMM_A3 Type : DDR3-Registered Size : 2048 MB Index : 3 Status : Critical Connector Name : DIMM_B1 Type : DDR3-Registered Size : 2048 MB Index : 4 Status : Ok Connector Name : DIMM_B2 Type : DDR3-Registered Size : 2048 MB Index : 5 Status : Ok Connector Name : DIMM_B3 Type : DDR3-Registered Size : 2048 MB the command free -m shows this, the server seems to be using more than 10GB of ram which would suggest it is trying to use the DIMM total used free shared buffers cached Mem: 12004 10766 1238 0 384 4809 -/+ buffers/cache: 5572 6432 Swap: 2047 0 2047 iostat output while problem is occuring avg-cpu: %user %nice %system %iowait %steal %idle 52.82 0.00 11.01 0.00 0.00 36.17 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 47.00 0.00 576.00 0 576 sda1 0.00 0.00 0.00 0 0 sda2 1.00 0.00 32.00 0 32 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 46.00 0.00 544.00 0 544 avg-cpu: %user %nice %system %iowait %steal %idle 53.12 0.00 7.81 0.00 0.00 39.06 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 592.00 0 592 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 592.00 0 592 avg-cpu: %user %nice %system %iowait %steal %idle 56.09 0.00 7.43 0.37 0.00 36.10 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 232.00 0.00 64520.00 0 64520 sda1 0.00 0.00 0.00 0 0 sda2 159.00 0.00 63728.00 0 63728 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 73.00 0.00 792.00 0 792 avg-cpu: %user %nice %system %iowait %steal %idle 52.18 0.00 9.24 0.06 0.00 38.51 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 49.00 0.00 600.00 0 600 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 49.00 0.00 600.00 0 600 avg-cpu: %user %nice %system %iowait %steal %idle 54.82 0.00 8.64 0.00 0.00 36.55 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 100.00 0.00 2168.00 0 2168 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 100.00 0.00 2168.00 0 2168 avg-cpu: %user %nice %system %iowait %steal %idle 54.78 0.00 6.75 0.00 0.00 38.48 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 84.00 0.00 896.00 0 896 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 84.00 0.00 896.00 0 896 avg-cpu: %user %nice %system %iowait %steal %idle 54.34 0.00 7.31 0.00 0.00 38.35 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 81.00 0.00 840.00 0 840 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 81.00 0.00 840.00 0 840 avg-cpu: %user %nice %system %iowait %steal %idle 55.18 0.00 5.81 0.44 0.00 38.58 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 317.00 0.00 105632.00 0 105632 sda1 0.00 0.00 0.00 0 0 sda2 224.00 0.00 104672.00 0 104672 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 93.00 0.00 960.00 0 960 avg-cpu: %user %nice %system %iowait %steal %idle 55.38 0.00 7.63 0.00 0.00 36.98 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 74.00 0.00 800.00 0 800 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 74.00 0.00 800.00 0 800 avg-cpu: %user %nice %system %iowait %steal %idle 56.43 0.00 7.80 0.00 0.00 35.77 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 72.00 0.00 784.00 0 784 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 72.00 0.00 784.00 0 784 avg-cpu: %user %nice %system %iowait %steal %idle 54.87 0.00 6.49 0.00 0.00 38.64 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 80.20 0.00 855.45 0 864 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 80.20 0.00 855.45 0 864 avg-cpu: %user %nice %system %iowait %steal %idle 57.22 0.00 5.69 0.00 0.00 37.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 33.00 0.00 432.00 0 432 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 33.00 0.00 432.00 0 432 avg-cpu: %user %nice %system %iowait %steal %idle 56.03 0.00 7.93 0.00 0.00 36.04 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 41.00 0.00 560.00 0 560 sda1 0.00 0.00 0.00 0 0 sda2 2.00 0.00 88.00 0 88 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 39.00 0.00 472.00 0 472 avg-cpu: %user %nice %system %iowait %steal %idle 55.78 0.00 5.13 0.00 0.00 39.09 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 29.00 0.00 392.00 0 392 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 29.00 0.00 392.00 0 392 avg-cpu: %user %nice %system %iowait %steal %idle 53.68 0.00 8.30 0.06 0.00 37.95 Device: tps Blk_read/s Blk_wrtn/s Blk_read Blk_wrtn sda 78.00 0.00 4280.00 0 4280 sda1 0.00 0.00 0.00 0 0 sda2 0.00 0.00 0.00 0 0 sda3 0.00 0.00 0.00 0 0 sda4 0.00 0.00 0.00 0 0 sda5 78.00 0.00 4280.00 0 4280

  Read the article

• 10.10 freezing when sftp downloading

  - by aGr

  My ubuntu 10.10 is freezing during downloading from my other computer on sftp. I thought it might be some nautilus issues so I tried it via command line and I got the same thing - after few minutes the whole computer freezes. Mostly the numlock led is blinking (I've heard somewhere that this means a kernel panic), but not in 100% cases. I dunno if that helps but here is a log from /var/log/message in the time that this happened. At least I hope so - it wasn't that big, when it happened before. But this looks quite "errorish", right? (isn't complete - see bottom) Jan 5 17:57:49 tomas-ntb kernel: imklog 4.2.0, log source = /proc/kmsg started. Jan 5 17:57:49 tomas-ntb rsyslogd: [origin software="rsyslogd" swVersion="4.2.0" x-pid="953" x-info="http://www.rsyslog.com"] (re)start Jan 5 17:57:49 tomas-ntb rsyslogd: rsyslogd's groupid changed to 103 Jan 5 17:57:49 tomas-ntb rsyslogd: rsyslogd's userid changed to 101 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Initializing cgroup subsys cpuset Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Initializing cgroup subsys cpu Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Linux version 2.6.35-24-generic (buildd@vernadsky) (gcc version 4.4.5 (Ubuntu/Linaro 4.4.4-14ubuntu5) ) #42-Ubuntu SMP Thu Dec 2 01:41:57 UTC 2010 (Ubuntu 2.6.35-24.42-generic 2.6.35.8) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-provided physical RAM map: Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009e800 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 00000000dffa8000 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffa8000 - 00000000dffb0000 (ACPI NVS) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffb0000 - 00000000dffbff00 (ACPI data) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dffbff00 - 00000000dfff0000 (ACPI NVS) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000dfff0000 - 00000000e0000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000100000000 - 0000000120000000 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] BIOS-e820: 0000000120000000 - 0000000140000000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] DMI 2.5 present. Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] last_pfn = 0xdffa8 max_arch_pfn = 0x100000 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] Scanning 0 areas for low memory corruption Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified physical RAM map: Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000010000 - 000000000009e800 (usable) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 000000000009e800 - 00000000000a0000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved) Jan 5 17:57:49 tomas-ntb kernel: [ 0.000000] modified: 0000000000100000 - 00000000dffa8000 (usable) ... to long - for whole and better view click here

  Read the article

• Which GPU with my CPU for 1080p flash?

  - by oshirowanen

  Based on the following site: http://www.adobe.com/products/flashplayer/systemreqs/ I need the following minimum spec to play 1080p flash video via a browser: CPU: 1.8GHz Intel Core Duo, AMD Athlon 64 X2 4200+, or faster processor RAM: 512MB of RAM GPU: 64MB of graphics memory I only have a 2.8GHz Pentium 4 process which is no where near as good as the processor listed above. I don't want to upgrade my processor as I think it will mean I have to change the motherboard etc. So, my question is, what is the cheapest PCI-E GPU I can buy which will allow me to play smooth 1080p flash video via a browser. I think the cheapest I can get is the 8400GS, but am not sure if that will be able to handle 1080p with the processor I have. I have looked at the GT520 and was wondering if this is the cheapest GPU which I need, or if there is something cheaper which will do 1080p with a 2.8GHz Pentium 4. Or, will I have to get something better than a GT520?

  Read the article

• VLC will sometimes have issues displaying video in fullscreen. What could cause this? How would I troubleshoot the issue?

  - by George Marian

  Recently VLC has been having issues displaying video in fullscreen mode. AFAIK, nothing has changed with the video card drivers and it's certainly the same version of VLC. (/me shakes a fist at the repository maintainers) This has worked without issue in the past. In fact, I've had as many as 6 instances of VLC running, each playing a video. One was always fullscreen on my second monitor, while the others were tiled on my primary monitor. I was able to toggle any of the other 5 into fullscreen mode and the video displayed without issue. Lately, I've been having trouble running 2 instances in fullscreen mode. (Sometimes, even a single instance will not display the video in fullscreen.) VLC will continue to play the video, but in fullscreen mode I see nothing but a black screen. Sometimes, the video will display if I maximize the VLC window. Other times, I have to settle for a smaller sized window. I don't know if this is pertinent, but sometimes changing the min/max state of a Firefox window (Minefield, specifically) seemed to allow the troublesome instance to display the video in fullscreen mode. However, that did not prove to be a consistent workaround. Sometimes, it seemed that closing a Firefox window did the trick, though that isn't consistently successful either. (I futzed with Firefox, because with the crazy number of windows and tabs that I normally have open, it regularly hogs about 1 GB of RAM.) Another bit of funkiness that comes to mind is the fact that my secondary monitor is considered the primary on boot-up. I use xrandr to designate the real 1st monitor as primary after boot-up, as suggested by someone in a question I asked on the Unix & Linux SE site. Specs: Ubuntu 10.10 w/ Gnome and Compiz 8GB RAM AMD Phenom II 965 Black Edition Asus M4A79 Deluxe mobo XFX ATI Radeon HD 5750 w/ 1GB RAM VLC is configured to use the hardware overlay for video (as per the default setting) Does anyone have an idea what may cause this issue or how I may go about troubleshooting it? Update: Right now I have 2 instances of VLC playing, each in fullscreen mode on a separate monitor. This is what I see:

  Read the article

• I can not connect to the Internet with cable

  - by Diego Castro

  tengo un computador de escritorio (board: gigabyte h61m, procesador: intel core i3 de 64 bits, ram: ddr3 4 GB) y puedo acceder a internet normalmente desde Windows 7 (mi conexión es por cable directamente al modem (referencias del modem: D-link DSL-2640T)) e instale Ubuntu 11.04 y no puedo acceder a internet, probé con Ubuntu 10.04 (que es el que tengo actualmente instalado) y tampoco funciono no se que debo configurar ni que hacer, simplemente no se conecta, he intentado cambiando de modo automatico a modo manual en ipv4 y colocando los datos correspondientes (dirección IP, máscara de red y servidores de DNS) y no logro conectarme aún, agradezco la ayuda machine traslator Hi, I have a desktop (board: gigabyte h61m, Processor: Intel Core i3 64-bit RAM: 4 GB ddr3) and I can access the internet normally from Windows 7 (my connection is wired directly to the modem (modem references : D-link DSL-2640T)) and install Ubuntu 11.04 and I can not access the internet, I tried Ubuntu 10.04 (which is what I have currently installed) and worked either not set or that I should do, just does not connect, I tried switching from automatic mode to manual mode ipv4 and placing the data (IP address, subnet mask and DNS servers) and I can not even connect, appreciate the help

  Read the article

• How to get Cinnamon working in Virtualbox?

  - by kavoura

  I installed Ubuntu 11.10 (32-bit) in VirtualBox 4.1.8. I wanted to install Cinnamon, so I did and I have the option to choose it from the login screen, as well as GNOME options. If I choose Ubuntu I get Unity, which works fine. GNOME also works. But when I choose Cinnamon, the screen goes black and nothing responds and I have to reset the virtual machine. I have already installed Ubuntu 11.10 (64-bit) onto the PC in a separate partition (currently running 10.10 but trying out 11.10) and in that Cinnamon works perfectly. In VirtualBox I have 3D settings enabled and gave the virtual machine 128 MB graphics RAM, and 1024 MB system RAM. What settings should I change or what should I do to get Cinnamon working in Ubuntu in VirtualBox? I have also tried doing it in LinuxMint 12, but I get the same problem, just a black screen when selecting Cinnamon. So are Cinnamon and VirtualBox incompatible?

  Read the article

• Installing 12.04 Ubuntu Studio on VMware Workstation 7, won't install VMware Tools

  - by Chase Kelley

  I'm attempting to install Ubuntu Studio 12.04 on my laptop by using VMware Workstation 7.1.5, and I've encountered a problem. The install goes well until the installation of Ubuntu has completed and the installation of VMware Tools starts; after that it just stops. I have waited about an hour and a half and nothing has changed. The installation is on VMware Easy Install, and I am running Windows Vista 32-bit with 3 GB system RAM and 2 GB of RAM on the virtual machine. Any help is greatly appreciated, thank you!

  Read the article

• 10 Windows Tweaking Myths Debunked

  - by Chris Hoffman

  Windows is big, complicated, and misunderstood. You’ll still stumble across bad advice from time to time when browsing the web. These Windows tweaking, performance, and system maintenance tips are mostly just useless, but some are actively harmful. Luckily, most of these myths have been stomped out on mainstream sites and forums. However, if you start searching the web, you’ll still find websites that recommend you do these things. Erase Cache Files Regularly to Speed Things Up You can free up disk space by running an application like CCleaner, another temporary-file-cleaning utility, or even the Windows Disk Cleanup tool. In some cases, you may even see an old computer speed up when you erase a large amount of useless files. However, running CCleaner or similar utilities every day to erase your browser’s cache won’t actually speed things up. It will slow down your web browsing as your web browser is forced to redownload the files all over again, and reconstruct the cache you regularly delete. If you’ve installed CCleaner or a similar program and run it every day with the default settings, you’re actually slowing down your web browsing. Consider at least preventing the program from wiping out your web browser cache. Enable ReadyBoost to Speed Up Modern PCs Windows still prompts you to enable ReadyBoost when you insert a USB stick or memory card. On modern computers, this is completely pointless — ReadyBoost won’t actually speed up your computer if you have at least 1 GB of RAM. If you have a very old computer with a tiny amount of RAM — think 512 MB — ReadyBoost may help a bit. Otherwise, don’t bother. Open the Disk Defragmenter and Manually Defragment On Windows 98, users had to manually open the defragmentation tool and run it, ensuring no other applications were using the hard drive while it did its work. Modern versions of Windows are capable of defragmenting your file system while other programs are using it, and they automatically defragment your disks for you. If you’re still opening the Disk Defragmenter every week and clicking the Defragment button, you don’t need to do this — Windows is doing it for you unless you’ve told it not to run on a schedule. Modern computers with solid-state drives don’t have to be defragmented at all. Disable Your Pagefile to Increase Performance When Windows runs out of empty space in RAM, it swaps out data from memory to a pagefile on your hard disk. If a computer doesn’t have much memory and it’s running slow, it’s probably moving data to the pagefile or reading data from it. Some Windows geeks seem to think that the pagefile is bad for system performance and disable it completely. The argument seems to be that Windows can’t be trusted to manage a pagefile and won’t use it intelligently, so the pagefile needs to be removed. As long as you have enough RAM, it’s true that you can get by without a pagefile. However, if you do have enough RAM, Windows will only use the pagefile rarely anyway. Tests have found that disabling the pagefile offers no performance benefit. Enable CPU Cores in MSConfig Some websites claim that Windows may not be using all of your CPU cores or that you can speed up your boot time by increasing the amount of cores used during boot. They direct you to the MSConfig application, where you can indeed select an option that appears to increase the amount of cores used. In reality, Windows always uses the maximum amount of processor cores your CPU has. (Technically, only one core is used at the beginning of the boot process, but the additional cores are quickly activated.) Leave this option unchecked. It’s just a debugging option that allows you to set a maximum number of cores, so it would be useful if you wanted to force Windows to only use a single core on a multi-core system — but all it can do is restrict the amount of cores used. Clean Your Prefetch To Increase Startup Speed Windows watches the programs you run and creates .pf files in its Prefetch folder for them. The Prefetch feature works as a sort of cache — when you open an application, Windows checks the Prefetch folder, looks at the application’s .pf file (if it exists), and uses that as a guide to start preloading data that the application will use. This helps your applications start faster. Some Windows geeks have misunderstood this feature. They believe that Windows loads these files at boot, so your boot time will slow down due to Windows preloading the data specified in the .pf files. They also argue you’ll build up useless files as you uninstall programs and .pf files will be left over. In reality, Windows only loads the data in these .pf files when you launch the associated application and only stores .pf files for the 128 most recently launched programs. If you were to regularly clean out the Prefetch folder, not only would programs take longer to open because they won’t be preloaded, Windows will have to waste time recreating all the .pf files. You could also modify the PrefetchParameters setting to disable Prefetch, but there’s no reason to do that. Let Windows manage Prefetch on its own. Disable QoS To Increase Network Bandwidth Quality of Service (QoS) is a feature that allows your computer to prioritize its traffic. For example, a time-critical application like Skype could choose to use QoS and prioritize its traffic over a file-downloading program so your voice conversation would work smoothly, even while you were downloading files. Some people incorrectly believe that QoS always reserves a certain amount of bandwidth and this bandwidth is unused until you disable it. This is untrue. In reality, 100% of bandwidth is normally available to all applications unless a program chooses to use QoS. Even if a program does choose to use QoS, the reserved space will be available to other programs unless the program is actively using it. No bandwidth is ever set aside and left empty. Set DisablePagingExecutive to Make Windows Faster The DisablePagingExecutive registry setting is set to 0 by default, which allows drivers and system code to be paged to the disk. When set to 1, drivers and system code will be forced to stay resident in memory. Once again, some people believe that Windows isn’t smart enough to manage the pagefile on its own and believe that changing this option will force Windows to keep important files in memory rather than stupidly paging them out. If you have more than enough memory, changing this won’t really do anything. If you have little memory, changing this setting may force Windows to push programs you’re using to the page file rather than push unused system files there — this would slow things down. This is an option that may be helpful for debugging in some situations, not a setting to change for more performance. Process Idle Tasks to Free Memory Windows does things, such as creating scheduled system restore points, when you step away from your computer. It waits until your computer is “idle” so it won’t slow your computer and waste your time while you’re using it. Running the “Rundll32.exe advapi32.dll,ProcessIdleTasks” command forces Windows to perform all of these tasks while you’re using the computer. This is completely pointless and won’t help free memory or anything like that — all you’re doing is forcing Windows to slow your computer down while you’re using it. This command only exists so benchmarking programs can force idle tasks to run before performing benchmarks, ensuring idle tasks don’t start running and interfere with the benchmark. Delay or Disable Windows Services There’s no real reason to disable Windows services anymore. There was a time when Windows was particularly heavy and computers had little memory — think Windows Vista and those “Vista Capable” PCs Microsoft was sued over. Modern versions of Windows like Windows 7 and 8 are lighter than Windows Vista and computers have more than enough memory, so you won’t see any improvements from disabling system services included with Windows. Some people argue for not disabling services, however — they recommend setting services from “Automatic” to “Automatic (Delayed Start)”. By default, the Delayed Start option just starts services two minutes after the last “Automatic” service starts. Setting services to Delayed Start won’t really speed up your boot time, as the services will still need to start — in fact, it may lengthen the time it takes to get a usable desktop as services will still be loading two minutes after booting. Most services can load in parallel, and loading the services as early as possible will result in a better experience. The “Delayed Start” feature is primarily useful for system administrators who need to ensure a specific service starts later than another service. If you ever find a guide that recommends you set a little-known registry setting to improve performance, take a closer look — the change is probably useless. Want to actually speed up your PC? Try disabling useless startup programs that run on boot, increasing your boot time and consuming memory in the background. This is a much better tip than doing any of the above, especially considering most Windows PCs come packed to the brim with bloatware.     

  Read the article

• Unity very slow while Gnome Classic running just fine

  - by Sorin Sbarnea

  I see tons of people complaining about Unity speed and I think the problem is not with the video drivers. When I login to Gnome Classic the system is behaving just fine, but when on Unity I can barely do use it: windows are moved hard, terminal is damn slow. Is there any solution or bug that I should track? Details Ubuntu 11.10 Two monitors setup Latest Nvidia proprietary drivers (tested with default ones also, no change) 6GB RAM, Xeon @ 2.8 Nvidia Driver 280.13 - Quadro NVS 295 with 8 cores 256MB RAM. lspci | grep VGA 02:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 295] (rev a1) uname -a Linux sorins 3.0.0-16-generic #29-Ubuntu SMP Tue Feb 14 12:48:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• New Computer

  - by Matt Christian

  Last night I received my computer that was ordered with my tax return money.  Here are the specs of my old computer: - Pentium 4 Processor - 3-4 GB RAM - ~256 GB HDD space (2 drives) - nVidia card (AGP 8x) Sorry I can't be more specific, my memory is gone :p  Here are the new computer specs (mostly): - 2.8ghz Pentium i7 quadcore - 6 GB RAM - 1 TB HDD space (1 drive) - 1 GB Radeon card (PCI-X) I also got a new monitor (22" Asus with HDMI) so will be using my 19" widescreen as a secondary monitor. If I remember I'll hop on here and post the specifics later on...

  Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >