Search Results

Search found 2863 results on 115 pages for 'sms gateway'.

Page 42/115 | < Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >

  • what firefall linux distro applicance could track internet usage per device in my home?

    - by GregH
    Hello, Anyone know of a community edition/open source/free firewall/gateway software product that I could install onto an old PC to act as my firewall/gateway/proxy etc, BUT for which it has the power to track internet usage per device in my home. So: a) Mandatory - Track internet usage for devices on my home network on a per device basis (e.g. various PCs/Xbox etc) b) Mandatory - Report/graph would would give a breakdown of internet usage, per device (e.g. IP address), per day. c) Desirable - as in b) above but per hour d) Desirable - realtime graph (e.g. 5 minute measurement intervals or something) that shows current internet usage per device e) Mandatory - Handles all internal<=internet requests for all protocols (e.g. HTTP, HTTPS, xbox etc) f) Mandatory - No explicit settings in clients required - i.e. Transparent Monitoring concept (for both HTTP and non-HTTP traffic like xbox, skype etc) g) Mandatory - easy "appliance" like installation onto a dedicated low spec PC thanks in advance

    Read the article

  • DNS Settings in Cisco Wireless Lan Controllers

    - by Braden
    The WLC is a 2100 series and I have looked back and forth through the entire web interface. Originally the idea was that the gateway should be the DNS controler and the WLC pointed directly at the gateway. For some reason, random clients are having DNS specific issues when it comes to seeing certain shares around the network. The problems are also very intermittent. Aside from going to each box and implementing a static DNS is there ACTUALLY a DNS setting lodged into the WLC settings (and I am being a numpty and can't find them) or am I stuck with performing the config 1 by 1?

    Read the article

  • IP route ppp0 + eth0 access to outside network

    - by Vitor
    I need some help in define a route I have two connections one from eth0 and other a ppp0 (a 3G card) Not having the ppp0 connection active my route table is: Destination Gateway Genmask Flags Metric Ref Use Iface default DD-WRT 0.0.0.0 UG 100 0 0 eth0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 I can access my webserver from an outside network through ethernet interface Than I have also my ppp0 3G connection active havig the following route table: D estination Gateway Genmask Flags Metric Ref Use Iface default 10.64.64.64 0.0.0.0 UG 0 0 0 ppp0 10.64.64.64 * 255.255.255.255 UH 0 0 0 ppp0 192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 Now I only can access my webserver in outside networks through the IP of the 3G connection Note that my server is serving at 0.0.0.0 IP (to all interfaces) But I need to get access to webserver to both interfaces ethernet and 3G connection I only can have access to both connection in local network Any help to configure this network to have both interfaces with outside networks access is welcome Can anyone give me an example to configure this network with 2 gateways to give outside networks access One for IP 192.168.1.149 and other for the ppp0 IP 89.214.60.196 Tanks

    Read the article

  • VPN Split Tunneling - Pros and Cons and how to achieve?

    - by Theveloper
    Well this is the dilemma, I want remote clients to connect to my network and only route local access through the VPN. This is split tunneling, the client uses its internet connection for all other internet requests and the VPN tunnel to my network for local requests. There's a couple of issues that arise: split tunneling in Windows is achieved by unticking an option which reads "Use default gateway on remote network" in the TCP/IP settings of the client VPN connection. At any point the user can tick it and route all his internet traffic through my network eating away at my bandwidth and being cloaked by my IP address. This is unacceptable. Issue number 2 is that if the client is split tunneling, he becomes a gateway between the internet and my network, this is also unacceptable. My questions are: how does one achieve split tunneling serverside? And is the latter issue a valid con worthy of worry? Any thoughts would be appreciated!

    Read the article

  • Windows Server firewall asking for advice

    - by George2
    Hello everyone, I have Windows Server 2003/2008 machine, and I deployed some application on this machine. I want to put this machine in a sandbox environment, which means I want this machine to be able to access only proxy/gateway, its private used SQL Server database server, and I want to avoid network access from this machine to other machines in lab server room. Any easy solutions? BTW: my current environment is, I have a server which runs some Beta software in a Lab server room. It connects internet through proxy/gateway. Since the software is Beta, I want to reduce the risk of being hacked from internet and controlled by hacking sofwtare to attack my other servers in the same Lab server. thanks in advance, George

    Read the article

  • DNS and DHCP dies after ~2 days of use on ClearOS

    - by TheLQ
    I'm using ClearOS (based on CentOS, so any info specific to it should apply here) as a gateway, DHCP, and DNS server. I had this server running perfectly for a month or two before replacing it with another server. However due DNS and DHCP failing 2 days in and a host of other performance issues (the box was a little underpowered), I changed back to the origional server. However 2 days in DHCP and DNS are failing again, and I'm out of idea's on why. In both cases to my knowledge no network or server changes occurred after installation. Right after installing (and at least a day in) DNS and DHCP was working just fine. However later (Day 2) I get a call saying their internet is down (translation: Nobody can get to websites because DNS is down) I've tried to fix the problem by checking if the dnsmasq is even running (it is), restarting the service, and restarting the server to no effect. I do have two internal servers that have static DHCP leases but one's lease must of expired as I can't connect to it anymore. I'm hesitant to do any dhcp testing on the last server as I'll not be able to connect to it anymore. Is there anything anyone can think of on why DNS and DHCP would fail 2 days in to running perfectly? More info: Running dnsmasq in debug mode. This is all that's displayed even when running nslookup quackwall. I'm not sure though if nslookup commands should show up in the log [root@quackwall ~]# /usr/sbin/dnsmasq -dq dnsmasq: started, version 2.49 cachesize 150 dnsmasq: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP dnsmasq-dhcp: DHCP, IP range 10.0.0.100 -- 10.0.0.254, lease time 12h dnsmasq: reading /etc/resolv.conf dnsmasq: using nameserver 74.128.17.114#53 dnsmasq: using nameserver 74.128.19.102#53 dnsmasq: read /etc/hosts - 5 addresses dnsmasq-dhcp: read /etc/ethers - 2 addresses On the other server DNS and the Gateway are all configured correctly (10.0.0.2 is quackwall) lordquackstar@quackgame:~$ netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.0.0.0 0.0.0.0 255.255.240.0 U 0 0 0 eth0 0.0.0.0 10.0.0.2 0.0.0.0 UG 0 0 0 eth0 lordquackstar@quackgame:~$ cat /etc/resolv.conf nameserver 10.0.0.2 domain highwow.lan search highwow.lan

    Read the article

  • Remote Access Problems with DRAC 5 on Dell PowerEdge 1950

    - by Darin Peterson
    Today I received my first Dell PowerEdge 1950 server with a DRAC 5 card. On my local network I have static configurations on my Linux systems using this for instance: iface eth0 inet static address 192.168.1.210 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 dns-nameservers 8.8.8.8 8.8.4.4 For the DRAC card, I configured the LAN like this: address 192.168.1.215 netmask 255.255.255.0 gateway 192.168.1.1 For the advanced LAN settings I used dns-nameservers 8.8.8.8 8.8.4.4 I've tried many different IP addresses, but cannot communicate with the card. Is there anyone who might know if I have configuration issues, or maybe if the card might be bad?

    Read the article

  • Motorola SBG6850 / Linksys WRT54G network problem

    - by user96407
    I am trying to resolve issues with connecting my desktop and LAN capable printer to my network. I recently upgrade to the Motorola Cable Modem Gateway SBG6580 and have TWC coming into it, this works great for wired and wireless connectivity. Although, I am unable to connect to my device from this modem gateway. So, I am trying to cable a Linksys WRT54G (firmware 4.21.4 build 0) to the backside of the SBG6850 so I can use my printer on my network from both my wired desktop and wireless devices. I am pulling wireless off of the SBG6580 and do not want to change this. I have disable the wireless feature on the Linksys WRT54G at this moment. Can someone please help me through this dilemma? I am open to both wired and wireless solutions, but please tell me which approach your sharing in the first line of your response. Cheers!

    Read the article

  • Mac OSX Server 10.6 DNS Issues

    - by dallasclark
    Hi, The server was upgraded from 10.5 from 10.6, during the upgrade the Reverse Zones were lost so I tried to recreate these but found that it's best to delete all zones, definitions and start again. So I've started again and Reverse Zones are appearing but I'm still having issues. I receive the following errors (if they help) 01-Nov-2010 12:52:01.254 client 192.168.1.52#57051: view com.apple.ServerAdmin.DNS.public: query (cache) 'server.dev.home.gateway/A/IN' denied 01-Nov-2010 12:59:24.487 client 192.168.1.52#52858: view com.apple.ServerAdmin.DNS.public: query (cache) 'earth.server.dev.home.gateway/A/IN' denied At the moment I have the following setup in the DNS 1.168.192.in-addr.arpa. Reverse Zone 192.168.1.100 Reverse Mapping MacPro-Server.local. server.dev. Primary Zone server.dev. Machine 192.168.1.100 earth.server.dev. Alias server.dev.

    Read the article

  • Internal USB A Female to motherboard 4-pin that mounts internally

    - by rockinthesixstring
    I'm wondering if anyone knows of a product like this but that is physically mountable internally rather than on a cable? I'm planning on building a super low profile "gateway" pc that is dedicated to handling internet traffic in my home. I have a great 1U rackmountable chassis for an ITX motherboard, but I need the hard drive real estate for the additional NIC required to run a gateway (one onboard and one PCI). So the plan is to use a small 8GB USB Jump Drive for the OS inside the box (as to not have one hanging out the back. And although it's racked, I still don't want the jump drive flopping around internally, so I want it fixed somehow. I have an alternative idea where by I use a flush mount zap strap saddle and a zip tie to hold it in place, but that seems kind of like a hack.

    Read the article

  • Network Configuration

    - by Dario
    Hello, This is my situation: Router A: IP 192.168.1.1 Mask 192.168.1.0/24 - Connected to the internet. Server: - Interface eth0: inet addr:10.1.1.125 Mask:255.255.255.0 (connected to router B) - Interface ra0: inet addr:192.168.1.125 Mask:255.255.255.0 (connected to router A) Router B: IP 10.1.1.254 Mask 10.1.1.0/24 - Connected to Server's eth0 Computer: connected to Router B via WiFi connection. I configured a static route on Router B that use as default gateway 192.168.1.125 and i can ping that ip from computer. The problem is: how i can connect to the internet ? In other words, traffic coming from Server eth0 should use ra0 as gateway. Any suggestion ? Thank you

    Read the article

  • Database OR Array

    - by rezoner
    What is the exact point of using external database system if I have simple relations (95% querries are dependant on ID). I am storing users and their stats. Why would I use external database if I can have neat constructions like: db.users[32] = something Array of 500K users is not that big effort for RAM Pros are: no problematic asynchronity (instant results) easy export/import dealing with database like with a native object LITERALLY ps. and considerations: Would it be faster or slower to do collection[3] than db.query("select ... I am going to store it as a file/s There is only ONE application/process accessing this data, and the code is executed line by line - please don't elaborate about locking. Please don't answer with database propositions but why to use external DB over native array/object - I have experience in a few databases - that's not the case. What I am building is a client/gateway/server(s) game. Gateway deals with all users data, processing, authenticating, writing statistics e.t.c No other part of software needs to access directly to this data/database.

    Read the article

  • Configure VPN to access remote LAN network on Windows7

    - by PiotrK
    Situation: I have two Windows7 machines (PC and laptop). I've set PC as VPN server and laptop as VPN client using default built-in W7 network tools. I've disabled use default gateway in remote network on client machine, so client don't try to route all communication through VPN. I've routed port 1723 (TCP/UDP) on NAT to my server and enabled IPSec/PPTP/L2TP passthrough I've put my laptop in indepedent network (basically I've connected it via 3G network), connected to VPN server and checked ipconfig /all I've get: IP Address: 192.168.1.101 Mask: 255.255.255.255 Gateway: (none) LAN mask in server LAN network is 255.255.255.0 - I am surely missing something obvious, but Google doesn't give me any good advices; How can I access local LAN network from remote VPN client? How can I access local shared documents?

    Read the article

  • How do I configure OpenVPN for accessing the internet with one NIC?

    - by Lekensteyn
    I've been trying to get OpenVPN to work for three days. After reading many questions, the HOWTO, the FAQ and even parts of a guide to Linux networking, I cannot get my an Internet connection to the Internet. I'm trying to set up a OpenVPN server on a VPS, which will be used for: secure access to the Internet bypassing port restrictions (directadmin/2222 for example) an IPv6 connection (my client does only have IPv4 connectivity, while the VPS has both IPv4 and native IPv6 connectivity) (if possible) I can connect to my server and access the machine (HTTP), but Internet connectivity fails completely. I'm using ping 8.8.8.8 for testing whether my connection works or not. Using tcpdump and iptables -t nat -A POSTROUTING -j LOG, I can confirm that the packets reach my server. If I ping to 8.8.8.8 on the VPS, I get an echo-reply from 8.8.8.8 as expected. When pinging from the client, I do not get an echo-reply. The VPS has only one NIC: etho. It runs on Xen. Summary: I want to have a secure connection between my laptop and the Internet using OpenVPN. If that works, I want to have IPv6 connectivity as well. Network setup and software: Home laptop (eth0: 192.168.2.10) (tap0: 10.8.0.2) | | (running Kubuntu 10.10; OpenVPN 2.1.0-3ubuntu1) | wifi | router/gateway (gateway 192.168.2.1) | INTERNET | VPS (eth0:1.2.3.4) (gateway, tap0: 10.8.0.1) (running Debian 6; OpenVPN 2.1.3-2) wifi and my home router should not cause problems since all traffic goes encrypted over UDP port 1194. I've turned IP forwarding on: # echo 1 > /proc/sys/net/ipv4/ip_forward iptables has been configured to allow forwarding traffic as well: iptables -F FORWARD iptables -A FORWARD -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A FORWARD -s 10.8.0.0/24 -j ACCEPT iptables -A FORWARD -j DROP I've tried each of these rules separately without luck (flushing the chains before executing): iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j SNAT --to 1.2.3.4 iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE route -n before (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n after (server): 1.2.3.4 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 0.0.0.0 1.2.3.4 0.0.0.0 UG 0 0 0 eth0 route -n before (client): 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 route -n after (client): 1.2.3.4 192.168.2.1 255.255.255.255 UGH 0 0 0 wlan0 10.8.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 192.168.2.0 0.0.0.0 255.255.255.0 U 2 0 0 wlan0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 wlan0 0.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 128.0.0.0 10.8.0.1 128.0.0.0 UG 0 0 0 tap0 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 wlan0 SERVER config proto udp dev tap ca ca.crt cert server.crt key server.key dh dh1024.pem server 10.8.0.0 255.255.255.0 push "redirect-gateway def1" ifconfig-pool-persist ipp.txt keepalive 10 120 tls-auth ta.key 0 comp-lzo user nobody group nobody persist-key persist-tun log-append openvpn-log verb 3 mute 10 CLIENT config dev tap proto udp remote 1.2.3.4 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert client.crt key client.key ns-cert-type server tls-auth ta.key 1 comp-lzo verb 3 mute 20 traceroute 8.8.8.8 works as expected (similar output without OpenVPN activated): 1 10.8.0.1 (10.8.0.1) 24.276 ms 26.891 ms 29.454 ms 2 gw03.sbp.directvps.nl (178.21.112.1) 31.161 ms 31.890 ms 34.458 ms 3 ge0-v0652.cr0.nik-ams.nl.as8312.net (195.210.57.105) 35.353 ms 36.874 ms 38.403 ms 4 ge0-v3900.cr0.nik-ams.nl.as8312.net (195.210.57.53) 41.311 ms 41.561 ms 43.006 ms 5 * * * 6 209.85.248.88 (209.85.248.88) 147.061 ms 36.931 ms 28.063 ms 7 216.239.49.36 (216.239.49.36) 31.109 ms 33.292 ms 216.239.49.28 (216.239.49.28) 64.723 ms 8 209.85.255.130 (209.85.255.130) 49.350 ms 209.85.255.126 (209.85.255.126) 49.619 ms 209.85.255.122 (209.85.255.122) 52.416 ms 9 google-public-dns-a.google.com (8.8.8.8) 41.266 ms 44.054 ms 44.730 ms If you have any suggestions, please comment or answer. Thanks in advance.

    Read the article

  • Re-streaming RTMP stream

    - by Yvan JANSSENS
    I have a set of local RTMP stream servers in my network, but I want them to be reachable outside. The bandwidth is too narrow to serve multiple clients on the streamservers of my network, so the idea is to pull the local RTMP streams on a computer serving as a gateway, which pushes them on his turn to a hosted streaming provider. It is not possible to let the sources of the stream push their stream directly to the server outside due to network policy restrictions. Scheme of what I'm trying to accomplish: Internal network | External network ------------ ------------ ----------------------- | internal | <---- | Gateway | ------> | streamserver outside| | streams | ------------ ----------------------- ------------ | ^ | | | ----------- | | clients | | ----------- My question now is: which application which can pull a live stream from an RTMP source (Flash Media Server) and push it to another one (Flash Media Server at hosting provider).

    Read the article

  • Multiple External IP Ranges on a Juniper SSG5

    - by Sam
    I have a Juniper SSG 5 firewall in a datacenter. The first interface (eth0/0) has been assigned a static IP address and has three other addresses configured for VIP Nat. I have a static route configured at the lowest priority for 0.0.0.0/0 to my hosting company's gateway. Now I need to configure a second IP block. I have the IPs assigned to the second interface (eth0/1) which is in the same security zone and virtual router as the first. However, with this interface enabled I (a) can't initiate outbound sessions (browse the internet, ping, DNS lookup, etc) even though I can access servers behind the firewall just fine from the outside and (b) can't ping the management IP of the firewall/gateway. I've tried anything I can think of but I guess this is a little above my head. Could anyone point me in the right direction? Interfaces: ethernet0/0 xxx.xxx.242.4/29 Untrust Layer3 ethernet0/1 xxx.xxx.152.0/28 Untrust Layer3 Routes: http://i.stack.imgur.com/60s41.png

    Read the article

  • Need assistance setting up Linux Router with 2 public lans

    - by user195407
    I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

    Read the article

  • Can't ping some IP addresses in the same subnet (LAN) Windows 2011 Server

    - by Ricardo
    Hi I’m running in Windows Small Server 2011 server standard (192.168.1.108), it’s my dhcp and dns server too, but suddenly all other users can’t get internet. My gateway is 192.168.1.1. After a lots of tested I can saw that my server can’t get into the router (192.168.1.1), and also into some others computers, but some other computers answer the ping command. In fact the same computer with the IP 192.168.1.9 didn't answer, but with the IP 192.168.1.63, it response! I have no routers, firewall, vlans or anything that disallow the traffic between computers, in fact when I changed the server IP address (192.168.1.109), I be able to ping the other computers and gateway, but if a back to the 192.168.1.108 the trouble comeback. I hope you can help me with this issue Ricardo

    Read the article

  • How can I join two simple home networks together using an ethernet cable?

    - by Ilia Jerebtsov
    I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

    Read the article

  • Ubuntu box static routing problem

    - by Rafael
    Hello, I'm trying to configure a ubuntu server to be a router. This is my interface configuration (eth2 connects to my WAN, eth0 to my LAN): auto eth2 iface eth2 inet static address 192.168.0.249 netmask 255.255.255.0 gateway 192.168.0.1 broadcast 192.168.0.255 auto eth0 iface eth0 inet static address 192.168.100.1 netmask 255.255.255.0 This is the router information: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 0.0.0.0 192.168.0.1 0.0.0.0 UG 100 0 0 eth2 And this is dhcp configuration: subnet 192.168.100.0 netmask 255.255.255.0 { range 192.168.100.101 192.168.100.254; option domain-name-servers 201.70.86.133; option routers 192.168.100.1; authoritative; } I'm then connecting a mac os x by cable on eth0. This is en0 interface configuration: en0: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:26:bb:5d:82:b0 inet6 fe80::226:bbff:fe5d:82b0%en0 prefixlen 64 scopeid 0x4 inet 192.168.100.101 netmask 0xffffff00 broadcast 192.168.100.255 media: autoselect (100baseTX <full-duplex>) status: active And this is the routing table: Internet: Destination Gateway Flags Refs Use Netif Expire default 192.168.100.1 UGSc 139 32 en0 10.37.129/24 link#8 UC 2 0 vnic1 10.37.129.2 0:1c:42:0:0:9 UHLWI 0 839 lo0 10.37.129.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic1 10.211.55/24 link#7 UC 2 0 vnic0 10.211.55.2 0:1c:42:0:0:8 UHLWI 0 840 lo0 10.211.55.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vnic0 127 127.0.0.1 UCS 0 0 lo0 127.0.0.1 127.0.0.1 UH 3 507924 lo0 169.254 link#4 UCS 0 0 en0 172.16.42/24 link#10 UC 2 0 vmnet8 172.16.42.1 0:50:56:c0:0:8 UHLWI 0 839 lo0 172.16.42.255 link#10 UHLWbI 1 24 vmnet8 192.168.100 link#4 UC 2 0 en0 192.168.100.1 0:e0:7c:7e:f:99 UHLWI 139 0 en0 777 192.168.100.101 127.0.0.1 UHS 0 0 lo0 192.168.100.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 en0 192.168.116 link#9 UC 2 0 vmnet1 192.168.116.1 0:50:56:c0:0:1 UHLWI 0 839 lo0 192.168.116.255 ff:ff:ff:ff:ff:ff UHLWbI 0 4 vmnet1 When I ping 192.168.100.1, it works. When I ping 192.168.0.249, it also works. However, when I try to ping 192.168.0.1 it does not. Does anyone has any way to solve this? Is there a way to debug it? Thanks,

    Read the article

  • Using 2 Transparent HAProxy for load balancing

    - by Nyxynyx
    We can configure HAProxy to be a transparent proxy by using the guide here, where one of the steps says ...to put the backend servers in a different subnet to the front end clients and make sure that the default gateway points back at the HAProxy load balancer. However when we need to have 2 transparent HAProxy in front of our balanced servers (for redundancy), it seems like this wont work as we can only set one gateway for our balanced servers. What will be the correct way to setup the system such that we can have 2 transparent HAProxy infront of the balanced servers? The main reason for having transparent proxies is the need to find the client's IP addresses over TCP.

    Read the article

  • procmail don't execute php script

    - by Phliplip
    Hi, I have setup a kannel SMS gateway on my FreeBSD 7.2 - the service works great. I'm now trying to setup a email2sms feature. For this i have created a system user called kannel and all mails are forwarded to this user. In the home dir of kannel i have the following files. -rw-r--r-- 1 kannel kannel 81B 17 jan 09:50 .procmailrc lrwxr-x--- 1 root kannel 58B 14 jan 13:24 email2sms.php @ -> some-what-some-where -rw-rw-rw- 1 root kannel 5,8K 17 jan 09:52 log.email2sms -rw------- 1 kannel kannel 1,3K 17 jan 09:50 procmail.log -rw-r----- 1 root kannel 606B 14 jan 13:28 rawmail.txt The file email2sms.php is a symlink to the a php script (ZendFramework Application) that takes the email from STDIN, and uses ZendFramework to parse that mail into an object. It then do a http request to the SMS gateway. The php-script works. Content of .procmailrc LOGFILE=$HOME/procmail.log VERBOSE=yes :0 | php email2sms.php >> log.email2sms From last sent email i have this in procmail.log procmail: [97744] Mon Jan 17 09:50:40 2011 procmail: [97744] Mon Jan 17 09:50:40 2011 procmail: Assigning "LASTFOLDER= php email2sms.php >> log.email2sms" procmail: Executing " php email2sms.php >> log.email2sms" procmail: Notified comsat: "kannel@:/home/user/kannel/ php email2sms.php >> log.email2sms" From [email protected] Mon Jan 17 09:50:40 2011 Subject: asdf as Folder: php email2sms.php >> log.email2sms 2600 But there is no new output to log.email2sms, and the script should output the subject of the email. If i sudo as the kannel user and pipe a file with raw email to the script, it executes just fine. [root@webserver /home/user/kannel]# /home/user/kannel/ sudo -u kannel cat rawmail.txt | php email2sms.php >> log.email2sms And the command outputs to log.email2sms as desired. Any ideas guys?

    Read the article

  • Mac OSX Server 10.6 DNS Issues

    - by dallasclark
    The server was upgraded from 10.5 from 10.6, during the upgrade the Reverse Zones were lost so I tried to recreate these but found that it's best to delete all zones, definitions and start again. So I've started again and Reverse Zones are appearing but I'm still having issues. I receive the following errors (if they help) 01-Nov-2010 12:52:01.254 client 192.168.1.52#57051: view com.apple.ServerAdmin.DNS.public: query (cache) 'server.dev.home.gateway/A/IN' denied 01-Nov-2010 12:59:24.487 client 192.168.1.52#52858: view com.apple.ServerAdmin.DNS.public: query (cache) 'earth.server.dev.home.gateway/A/IN' denied At the moment I have the following setup in the DNS 1.168.192.in-addr.arpa. Reverse Zone 192.168.1.100 Reverse Mapping MacPro-Server.local. server.dev. Primary Zone server.dev. Machine 192.168.1.100 earth.server.dev. Alias server.dev.

    Read the article

  • Virtual machine on ubuntu

    - by MITHIYA MOIZ
    I have configured virtual machine on ubuntu with the help of below article, https://help.ubuntu.com/9.04/serverguide/C/libvirt.html I managed to finish all the part except the major portion getting virtual host to talk to real network, Which I guess should be done only via bridge interface. Via virtual machine manager I try to choose any interface it gives me interface not bridged When I try to bridge the interceface eth0 as below auto br0 iface br0 inet static address 192.168.0.223 network 192.168.0.0 netmask 255.255.255.0 broadcast 192.168.0.255 gateway 192.168.0.1 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off I cannot communicate with this interface to network, host server looses all the communication to network. But when I remote bridge interface from /etc/network/interfaces And configure eth0 as below it works fine The primary network interface auto eth0 iface eth0 inet static address 192.168.0.223 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 dns-nameservers 62.215.6.51 gateway 192.168.0.1 how can i setup bridge interface correctly and how would my /etc/netwrok/interfaces file would look a like.

    Read the article

  • What equipment do real ISP's use?

    - by Allanrbo
    In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers?

    Read the article

< Previous Page | 38 39 40 41 42 43 44 45 46 47 48 49  | Next Page >