Search Results

Search found 2022 results on 81 pages for 'subnet mask'.

Page 43/81 | < Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >

  • Bridging and iptables SNAT conflict

    - by sad_admin
    Hello I am working on a setup here and have it working with one minor exception. Devices on one side of my bridge aren't getting SNAT'd to the Internet. The Diagram / Overview: Primary_Network (Site_A) | | Internet ------- Linux_Bridge_GW (GW) | | Secondary/CoLo Site (Site_B) Here is the setup: 1.) Site_A has all the production servers and workstations. 2.) Site_B has a set of servers that we would like to fail-over to and also serve our internet facing services from. 3.) GW has two interfaces that are trunked and carrying the appropriate VLAN traffic (allow layer-2 propagation of traffic between sites) //this all works perfectly fine. 4.) The problem that is being encountered is, hosts from Site_B have their default GW at Site_A (same subnet) GW does not have IPs on the VLANs that are being passed. 5.) All hosts at Site_A can reach the Internet without problem. 6.) GW has an addresses on a subnet that is ONLY for Internet destined traffic. (This was done so that Websense would not have to parse unnecessary traffic. We use this VLAN as the monitor port's source on the switch where Websense is sitting). What I think is happening: 1.) Packet/Frame comes in on physdev at Site_B destined for Internet. 2.) Kernel sees packet, and forwards it out the other side of the bridge to that host's default GW. 3.) Site_A (containing core-network's Default-GW) sees that packet is destined for a host it doesn't know about, so it sends it to it's default GW (the linux bridge, since it's Internet bound). 4.) The kernel says "Hey, I've seen you before" and therefore doesn't do SNAT'ing on the packet and sends it out to the Internet where it's black-holed. Why I think it's happening: 1.) A tcpdump on the internet facing NIC shows the packet leaving the interface with the private address as it's source. What I would like: 1.) Have the packet SNAT'd. 2.) Something like the below would be awesome a.) packet comes in from Site_B b.) kernel sees that the packet is NOT destined for itself or any private address c.) kernel says "OK, well since you're destined for the Internet I'm going to send you out this interface rather than forward you to your normal default GW that's WAAAY over there." d.) packet comes in from internet and is sent out the appropriate bridge physdev depending on which site the host it's destined for is at. Thanks for any assistance or guidance that you are willing to offer. Best Regards, Sad Admin

    Read the article

  • VPN says connected but cannot ping tunnel ip

    - by Owl
    I have a VPN set up on a Symantec Gateway 320 and the status of the VPN is connected but the feature it provides is not working which means it is not actually connected..The only way to test it other than trying to use it in the program that utilizes it is to ping the remote subnet IP we use. mask numbers match, no settings have been changed it just stopped working.

    Read the article

  • New to networking had to reinstall xp what does blank in Default Gateway mean?

    - by waterfallraini
    I have reinstalled windows xp and posted about not being able to connect to the Interenet. I did go and ensure all drivers are there and now when I type ipconfig/all I get physical address, dhcp enabled, autoconfiguration enabled, autoconfiguration Ip address, subnet mask and then a line that says default gateway where default gateway is the only line with no numbers or anything next to it. My wireless connection works but how can I get this ethernet connection to work. This was working prior to this fresh reinstall.

    Read the article

  • [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

    - by Beco
    I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

    Read the article

  • Routing between same networks

    - by osmandfj
    I have two different sites: NetA has a subnet 192.168.2.0/24 NetB has 192.168.1.0/24. The two sites connect each other via IPsec VPN with fortigate devices. I need to move a server with IP address 192.168.2.240 from NetA to NetB and I cannot change its IP address due to some specific reasons. My question is; if I move that server from NetA to NetB, is it possible to reach that server from NetA?

    Read the article

  • No external network on ubuntu 9.10, though dns works..

    - by user29368
    Hi, I have a weird problem I cant solve. I have several computers, two with xubuntu 9.10 One of them, acting as a media server, has stopped to work when it comes to external network.. I can do for example: ping google.com Which gives me an ip adress back, like: name@Media:/etc$ ping google.com PING google.com (66.102.9.147) 56(84) bytes of data. That tells me it reaches the dns?, but I get no response at all... If I ping a local computer all works fine. I can also reach the computer via ssh without any problems. I have always used network manager, but now I uninstalled it and made the settings manually like this: /etc/network/interfaces auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 192.168.1.52 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.1 Still no luck. I have no specific settings for this one in my router, and all the other computers, including my win laptop works fine. This is very annoying since I cant even do an update or anything.. ifconfig looks like this: eth0 Link encap:Ethernet HWaddr 00:24:1d:9f:10:89 inet addr:192.168.1.52 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::224:1dff:fe9f:1089/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15410 errors:0 dropped:0 overruns:0 frame:0 TX packets:2693 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1167398 (1.1 MB) TX bytes:694973 (694.9 KB) Interrupt:27 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2150 errors:0 dropped:0 overruns:0 frame:0 TX packets:2150 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:143456 (143.4 KB) TX bytes:143456 (143.4 KB) route -n like this Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 100 0 0 eth0 I do not know where the adress starting with 169.254 comes from.. Could that be a part of the problem? Hoping for some assistance since Im totally stuck here.. /george

    Read the article

  • move element li into ul with jquery

    - by ron
    Hi everybody i'm looking for a solution to move an element that i need to move into a .... im using jquery and i leave here the code i tried with different things but wasn't working it. this is the big menu <ul class="sf-menu"> <li><a href="">Student Centre</a> <ul> <li><a href="9">STUDENT CENTRAL WEBSITE</a></li> <li><a href="10">STUDENT CENTRAL EMAIL</a></li> <li><a href="11">CCM STUDENT SURVIAL TIPS</a></li> <li><a href="12">VET TUTTTION ASSURANSE</a></li> <li><a href="13">WHAT GOING ON AT CCM</a></li> <li><a href="14">IMPORTANT STUDENTS NOTICE</a></li> </ul> </li> <li><a href="">Research</a> <ul> <li><a href="_16">WHAT IS HOLISTIC KINESIOLOGY ?</a></li> <li><a href="_17">TRANF. CHILDREN W/ LEARNING DIFFICULTIES</a></li> <li><a href="_18">HEALING WITH HOLISTIC KINESIOLOGY</a></li> <li><a href="_19">UNDERSTANDING ASPERGER'S SYNDROME</a></li> <li><a href="_20">DAVID CORBY THE DIRECTOR OF CCM</a></li> <li><a href="_21">HELPING PEOPLE CREATE THEIR OWN MIRACLES</a></li> <li><a href="_22">MAGNESIUM AND COLLOIDAL MINERALS</a></li> <li><a href="_23">BRAIN ENERGETICS CHAKRAS AND NADIS</a></li> <li><a href="_24">KINESIOLOGY FAQ'S</a></li>' </ul> </li> <li><a href="25">Contact Us</a></li> <li><a href="26">A - Z</a></li> </ul> and i need to add this li to ul but i need to put in the second place after the first not nested <li id="faculty"> <a href="#">Faculty Courses </a> <ul> <li><a href="">INTENSE SHORT COURSES</a><ul> <li><a href="_59">CRYSTAL KINESIOLOGY ONE</a></li> <li><a href="_60">APPLIED PHYSIOLOGY</a></li> <li><a href="_61">VIBRATIONAL HEALING SYSTEMS 1</a></li> <li><a href="_62">VIBRATIONAL HEALING SYSTEMS 2</a></li> <li><a href="_63">VIBRATIONAL HEALING SYSTEMS 3</a></li> <li><a href="_64">VIBRATIONAL HEALING SYSTEMS 6</a></li> <li><a href="_65">NUTRITIONAL KINESIOLOGY</a></li> <li><a href="_66">QUANTUM HARMONICS</a></li><li><a href="_67">CHAKRA HOLOGRAM</a></li> <li><a href="_68">CLINICAL APPLICATIONS OF KINESIOLOGY</a></li> <li><a href="_69">COUNSELLING KINESIOLOGY</a></li> <li><a href="_70">HARMONISING CHI FLOW</a></li> </ul> </li> <li><a href="=53">FREE INTRUCTION COURSE DAYS</a> <ul> <li><a href="=53_56">HOLISTIC KINESIOLOGY</a></li> <li><a href="=53_57">TRANSPERSONAL COUNSELLING</a></li> <li><a href="=53_58">SHAMMANISM &amp; TRANSFORMATIONAL MASK</a></li> </ul> </li> <li><a href="=50">DIPLOMA MASK AND TRADITIONAL HEALING</a></li> <li><a href="=43">DIPLOMA TRANSPERSONAL ART THERAPY</a></li> <li><a href="=42">DIPLOMA HOLISTIC KINESIOLOGY</a></li> <li><a href="=47">ADVANCE DIPLOMA HOLISTIC KINESIOLOGY</a></li> <li><a href="=48">DIPLOMA DINAMIC AND FUNCTIONAL</a></li> <li><a href="=49">CERTIFICATE MASK AND TRADITIONAL HEALING</a></li> <li><a href="=51">DIPLOMA TRANSPERSONAL COUNSELLING</a></li> <li><a href="=52">STUDENT CLINICS</a></li> </ul> </li> please i need you help Thanks in advance

    Read the article

  • Image/"most resembling pixel" search optimization?

    - by SigTerm
    The situation: Let's say I have an image A, say, 512x512 pixels, and image B, 5x5 or 7x7 pixels. Both images are 24bit rgb, and B have 1bit alpha mask (so each pixel is either completely transparent or completely solid). I need to find within image A a pixel which (with its' neighbors) most closely resembles image B, OR the pixel that probably most closely resembles image B. Resemblance is calculated as "distance" which is sum of "distances" between non-transparent B's pixels and A's pixels divided by number of non-transparent B's pixels. Here is a sample SDL code for explanation: struct Pixel{ unsigned char b, g, r, a; }; void fillPixel(int x, int y, SDL_Surface* dst, SDL_Surface* src, int dstMaskX, int dstMaskY){ Pixel& dstPix = *((Pixel*)((char*)(dst->pixels) + sizeof(Pixel)*x + dst->pitch*y)); int xMin = x + texWidth - searchWidth; int xMax = xMin + searchWidth*2; int yMin = y + texHeight - searchHeight; int yMax = yMin + searchHeight*2; int numFilled = 0; for (int curY = yMin; curY < yMax; curY++) for (int curX = xMin; curX < xMax; curX++){ Pixel& cur = *((Pixel*)((char*)(dst->pixels) + sizeof(Pixel)*(curX & texMaskX) + dst->pitch*(curY & texMaskY))); if (cur.a != 0) numFilled++; } if (numFilled == 0){ int srcX = rand() % src->w; int srcY = rand() % src->h; dstPix = *((Pixel*)((char*)(src->pixels) + sizeof(Pixel)*srcX + src->pitch*srcY)); dstPix.a = 0xFF; return; } int storedSrcX = rand() % src->w; int storedSrcY = rand() % src->h; float lastDifference = 3.40282347e+37F; //unsigned char mask = for (int srcY = searchHeight; srcY < (src->h - searchHeight); srcY++) for (int srcX = searchWidth; srcX < (src->w - searchWidth); srcX++){ float curDifference = 0; int numPixels = 0; for (int tmpY = -searchHeight; tmpY < searchHeight; tmpY++) for(int tmpX = -searchWidth; tmpX < searchWidth; tmpX++){ Pixel& tmpSrc = *((Pixel*)((char*)(src->pixels) + sizeof(Pixel)*(srcX+tmpX) + src->pitch*(srcY+tmpY))); Pixel& tmpDst = *((Pixel*)((char*)(dst->pixels) + sizeof(Pixel)*((x + dst->w + tmpX) & dstMaskX) + dst->pitch*((y + dst->h + tmpY) & dstMaskY))); if (tmpDst.a){ numPixels++; int dr = tmpSrc.r - tmpDst.r; int dg = tmpSrc.g - tmpDst.g; int db = tmpSrc.g - tmpDst.g; curDifference += dr*dr + dg*dg + db*db; } } if (numPixels) curDifference /= (float)numPixels; if (curDifference < lastDifference){ lastDifference = curDifference; storedSrcX = srcX; storedSrcY = srcY; } } dstPix = *((Pixel*)((char*)(src->pixels) + sizeof(Pixel)*storedSrcX + src->pitch*storedSrcY)); dstPix.a = 0xFF; } This thing is supposed to be used for texture generation. Now, the question: The easiest way to do this is brute force search (which is used in example routine). But it is slow - even using GPU acceleration and dual core cpu won't make it much faster. It looks like I can't use modified binary search because of B's mask. So, how can I find desired pixel faster? Additional Info: It is allowed to use 2 cores, GPU acceleration, CUDA, and 1.5..2 gigabytes of RAM for the task. I would prefer to avoid some kind of lengthy preprocessing phase that will take 30 minutes to finish. Ideas?

    Read the article

  • Silent Partner

    - by [email protected]
    The Team Behind the Man Behind the Mask As a continuing sponsor of the blockbuster Iron Man franchise, Oracle has been quietly preparing for the explosive sequel blasting its way into theaters this May. Through a series of advertising campaigns, immersive online experiences, and contests, Oracle plans to highlight its backstage efforts to help Marvel Entertainment hone its newfound superpowers. By driving the performance of critical systems, Oracle technologies are helping Marvel transform itself from mild-mannered comic book publisher to film industry power broker. You can learn more about this dynamic duo, and get free movie memorabilia, by visiting our Iron Man 2 showcase site.

    Read the article

  • Network config with pppoe and Ubuntu 13.10

    - by Pavel
    I have an internet connection that is using pppoe. In my windows I do not assign an ip address for my network and I am able to connect using password and username. I installed Ubintu 13.10 today, and I did pppoeconf, and I setup an ip/network mask and changed the mac address in the options, and I was able to connect to the Internet. I restarted the computer, and I got a message saying that the wired connection is not managed. Internet was not working. I went to network manager file, and I changed the option to true, but I still can't connect to the Internet. I am pretty new to linux. How can I get my Internet working? Thanks

    Read the article

  • Wireless cuts out on Toshiba Satellite S7208

    - by alecRN
    I recently got a Toshiba Satellite L875-S7208 with Windows 7 preinstalled. I installed Ubuntu 12.04 LTS dual boot to the same Windows partition. However, usually 15 minutes or less after booting, the wifi connection dies. Here's some hopefully relevant information: lspci -knn 00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Panther Point USB xHCI Host Controller [8086:1e31] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: xhci_hcd 00:16.0 Communication controller [0780]: Intel Corporation Panther Point MEI Controller #1 [8086:1e3a] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: mei Kernel modules: mei 00:1a.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1b.0 Audio device [0403]: Intel Corporation Panther Point High Definition Audio Controller [8086:1e20] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb40] Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 1 [8086:1e10] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 2 [8086:1e12] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.2 PCI bridge [0604]: Intel Corporation Panther Point PCI Express Root Port 3 [8086:1e14] (rev c4) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller [0c03]: Intel Corporation Panther Point USB Enhanced Host Controller #1 [8086:1e26] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ehci_hcd 00:1f.0 ISA bridge [0601]: Intel Corporation Panther Point LPC Controller [8086:1e59] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: iTCO_wdt 00:1f.2 SATA controller [0106]: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] [8086:1e03] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel driver in use: ahci 00:1f.3 SMBus [0c05]: Intel Corporation Panther Point SMBus Controller [8086:1e22] (rev 04) Subsystem: Toshiba America Info Systems Device [1179:fb41] Kernel modules: i2c-i801 02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter [10ec:8176] (rev 01) Subsystem: Realtek Semiconductor Co., Ltd. Device [10ec:8211] Kernel driver in use: rtl8192ce Kernel modules: rtl8192ce 03:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Subsystem: Toshiba America Info Systems Device [1179:fb37] Kernel driver in use: r8169 Kernel modules: r8169 lsmod Module Size Used by snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224066 1 joydev 17693 0 rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 arc4 12529 2 snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 87692 0 serio_raw 13211 0 rtl8192ce 84826 0 rtl8192c_common 75767 1 rtl8192ce rtlwifi 111202 1 rtl8192ce mac80211 506816 3 rtl8192ce,rtl8192c_common,rtlwifi snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device sparse_keymap 13890 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev mac_hid 13253 0 mei 41616 0 wmi 19256 0 soundcore 15091 1 snd i915 472941 3 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm drm_kms_helper 46978 1 i915 cfg80211 205544 2 rtlwifi,mac80211 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp r8169 62099 0 ums_realtek 18248 0 uas 18180 0 usb_storage 49198 1 ums_realtek dmesg | grep firmware [ 15.692951] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 16.240881] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 452.419288] rtl8192c_common:rtl92c_firmware_selfreset(): 8051 reset fail. [ 458.572211] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 465.440640] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 472.337617] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 479.175471] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 485.978582] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 492.764893] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 499.579348] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 506.386934] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 513.209545] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 519.991365] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 526.778375] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 533.629695] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 540.426004] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 547.238125] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 554.024434] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 560.854794] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 567.678160] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 574.494666] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 581.336653] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 588.157710] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 595.221122] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 602.047429] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 608.829534] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 615.639079] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 622.454991] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 629.273231] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 636.056613] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 642.858096] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 649.640753] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 657.184094] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 664.008018] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 670.838639] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 677.675418] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 684.507255] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 691.310994] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 698.095325] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 704.914509] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin [ 711.725178] rtl8192c_common: Loading firmware file rtlwifi/rtl8192cfw.bin uname -r 3.2.0-29-generic ifconfig eth0 Link encap:Ethernet HWaddr 4c:72:b9:59:6c:61 inet addr:192.168.0.11 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe59:6c61/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4447 errors:0 dropped:0 overruns:0 frame:0 TX packets:2762 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3671147 (3.6 MB) TX bytes:335133 (335.1 KB) Interrupt:42 Base address:0x2000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:515 errors:0 dropped:0 overruns:0 frame:0 TX packets:515 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:83153 (83.1 KB) TX bytes:83153 (83.1 KB) wlan0 Link encap:Ethernet HWaddr 74:e5:43:32:47:95 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:280 errors:0 dropped:0 overruns:0 frame:0 TX packets:51 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:32958 (32.9 KB) TX bytes:10431 (10.4 KB)

    Read the article

  • dns hosting - url forwarding - hiding forwarded url?

    - by jeremycollins
    I have free dns hosting with the domain registrar and I'd like the dns hosted domain www.example.com to display contents of www.myotherlongdomain.com. I only have 301/302/iframe forwarding options, however I want to mask the redirected (longdomain) url. If I use frames, users can view the source and see the (longdomain) url the contents are coming from. How can I hide it so it always displays www.example.com? There is no cloaking/masking option with the registrar. Thanks.

    Read the article

  • Dlink DWA-556 Access point fails to start on 2.6.35-25 while 2.6.35-24 works. How can I do this with >2.6.35-24?

    - by Azendale
    I'm using hostapd to run an access point with a Dlink DWA-556 wireless N card. However, I can no longer get it to start when I use kernels greater than 2.6.35-24. Here's a log where I ran the uname -a&&hostapd -c <configfile> on the different kernel versions. Linux erikbandersen 2.6.35-24-generic #42-Ubuntu SMP Thu Dec 2 02:41:37 UTC 2010 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Flushing old station entries Deauthenticate all stations Using interface wlan1 with hwaddr 1c:bd:b9:d5:e8:3c and ssid 'erikbandersen.com/freewifi' wlan1: Setup of interface done. MGMT (TX callback) ACK Malformed netlink message: len=436 left=256 plen=420 256 extra bytes in the end of netlink message MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb mgmt::auth authentication: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=1 status_code=0 wep=0 New STA wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authentication OK (open system) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-AUTHENTICATE.indication(3c:4a:92:0e:41:2f, OPEN_SYSTEM) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) authentication reply: STA=3c:4a:92:0e:41:2f auth_alg=0 auth_transaction=2 resp=0 (IE len=0) MGMT (TX callback) ACK mgmt::auth cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: authenticated mgmt::assoc_req association request: STA=3c:4a:92:0e:41:2f capab_info=0x421 listen_interval=10 Validating WMM IE: OUI 00:50:f2 OUI type 2 OUI sub-type 0 version 1 QoS info 0x0 HT: STA 3c:4a:92:0e:41:2f HT Capabilities Info: 0x102c handle_assoc STA 3c:4a:92:0e:41:2f - no greenfield, num of non-gf stations 1 handle_assoc STA 3c:4a:92:0e:41:2f - 20 MHz HT, num of 20MHz HT STAs 1 hostapd_ht_operation_update current operation mode=0x0 hostapd_ht_operation_update new operation mode=0x7 changes=2 new AID 1 wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: association OK (aid 1) MGMT (TX callback) ACK mgmt::assoc_resp cb wlan1: STA 3c:4a:92:0e:41:2f IEEE 802.11: associated (aid 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-ASSOCIATE.indication(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) wlan1: STA 3c:4a:92:0e:41:2f RADIUS: starting accounting session 4DAC8224-00000000 MGMT (TX callback) ACK mgmt::action cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb MGMT (TX callback) ACK mgmt::proberesp cb Signal 2 received - terminating wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DEAUTHENTICATE.indication(3c:4a:92:0e:41:2f, 1) wlan1: STA 3c:4a:92:0e:41:2f MLME: MLME-DELETEKEYS.request(3c:4a:92:0e:41:2f) Removing station 3c:4a:92:0e:41:2f hostapd_ht_operation_update current operation mode=0x7 hostapd_ht_operation_update new operation mode=0x0 changes=2 Flushing old station entries Deauthenticate all stations . Linux erikbandersen 2.6.35-25-generic #44-Ubuntu SMP Fri Jan 21 17:40:44 UTC 2011 x86_64 GNU/Linux Configuration file: hostapd.conf ctrl_interface_group=0 Opening raw packet socket for ifindex 248 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) SIOCGIWRANGE: WE(compiled)=22 WE(source)=21 enc_capa=0xf nl80211: Added 802.11b mode based on 802.11g information Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=27 dBm Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=27 dBm HT40: control channel: 2 secondary channel: 6 RATE[0] rate=10 flags=0x2 RATE[1] rate=20 flags=0x6 RATE[2] rate=55 flags=0x6 RATE[3] rate=110 flags=0x6 RATE[4] rate=60 flags=0x0 RATE[5] rate=90 flags=0x0 RATE[6] rate=120 flags=0x0 RATE[7] rate=180 flags=0x0 RATE[8] rate=240 flags=0x0 RATE[9] rate=360 flags=0x0 RATE[10] rate=480 flags=0x0 RATE[11] rate=540 flags=0x0 Passive scanning not supported Mode: IEEE 802.11g Channel: 2 Frequency: 2417 MHz Could not set channel for kernel driver wlan1: Unable to setup interface. My wireless card is listed as 02:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless Network Adapter (rev 01) by lspci. Am I doing it wrong and there's a new way of doing it? I'm holding off upgrading to Natty because of this. What changed between the versions that would cause this? Should I report it as a bug?

    Read the article

  • Using IP Restrictions with URL Rewrite-Week 25

    - by OWScott
    URL Rewrite offers tremendous flexibility for customizing rules to your environment. One area of functionality that is often desired for URL Rewrite is to allow a large list of approved or denied IP addresses and subnet ranges. IIS’s original IP Restrictions is helpful for fully blocking an IP address, but it doesn’t offer the flexibility that URL Rewrite does. An example where URL Rewrite is helpful is where you want to allow only authorized IPs to access staging.yoursite.com, but where staging.yoursite.com is part of the same site as www.yoursite.com. This requires conditional logic for the user’s IP. This lesson covers this unique situation while also introducing Rewrite Maps, server variables, and pairing rules to add more flexibility. This is week 25 of a 52 week series for the Web Pro. Past and future videos can be found here: http://dotnetslackers.com/projects/LearnIIS7/ You can find this week’s video here.

    Read the article

  • I can not connect to the Internet with cable

    - by Diego Castro
    tengo un computador de escritorio (board: gigabyte h61m, procesador: intel core i3 de 64 bits, ram: ddr3 4 GB) y puedo acceder a internet normalmente desde Windows 7 (mi conexión es por cable directamente al modem (referencias del modem: D-link DSL-2640T)) e instale Ubuntu 11.04 y no puedo acceder a internet, probé con Ubuntu 10.04 (que es el que tengo actualmente instalado) y tampoco funciono no se que debo configurar ni que hacer, simplemente no se conecta, he intentado cambiando de modo automatico a modo manual en ipv4 y colocando los datos correspondientes (dirección IP, máscara de red y servidores de DNS) y no logro conectarme aún, agradezco la ayuda machine traslator Hi, I have a desktop (board: gigabyte h61m, Processor: Intel Core i3 64-bit RAM: 4 GB ddr3) and I can access the internet normally from Windows 7 (my connection is wired directly to the modem (modem references : D-link DSL-2640T)) and install Ubuntu 11.04 and I can not access the internet, I tried Ubuntu 10.04 (which is what I have currently installed) and worked either not set or that I should do, just does not connect, I tried switching from automatic mode to manual mode ipv4 and placing the data (IP address, subnet mask and DNS servers) and I can not even connect, appreciate the help

    Read the article

  • Cannot ping static ip on eth1

    - by Calvin Froedge
    I am trying to ping the network interface I have set up for eth1. This is my config: auto eth1 iface eth1 inet static address 192.168.1.2 netmask 255.255.255.0 gateway 192.168.1.1 broadcast 192.168.1.255 If I ping 192.168.1.2, I get: Ping 192.168.1.2 (192.168.1.2) 56(84) bytes of data. From 192.168.1.3 icmp_seq=3 Destination Host Unreachable Results of ifconfig tell me that the IPv4 address is 192.168.1.3. I can ping this ip. Bcast and Mask are as expected (same as in definition). I can ping 192.168.1.3 from my macbook. I cannot ping 192.168.1.2 locally or from my macbook. Any ideas why?

    Read the article

  • Connecting 2 ubuntu machines as a LAN

    - by Brendan Cutjar
    Hi i am trying to connect 2 ubuntu computers as a LAN. In my current setup I have: One machine running ubuntu 11.10 with Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller While the other machine is running Ubuntu 12.04 with an Atheros Communications Inc AR8152 v1.1 Fast Ethernet The two machines are connected via a switch (Edimax ES-3205P). Unfortunately I still cannot connect the two machines together. Can somebody please show me what to do and how to go about solving this issue? Thank you ANSWERED All I had to do was set up both ip's maually, subnet mask to 255.255.255.0 and left blank both gateway and DNS.

    Read the article

  • Why is there a "new" keyword in Go?

    - by dystroy
    I'm still puzzled as why we have new in Go. &Thing{} is as clear and concise as new(Thing) to Go coders and it uses only constructs you often use elsewhere. It's also more extensible as you might change it to &Thing{3} or &Thing{Feets:7}. In my opinion, having a supplementary keyword is costly, it makes the language more complex and adds to what you must know. And it might mask to newcomers what's behind instantiating a struct. It also makes one more reserved word. So what's the reasoning behind new ? Is it something useful ? Should we use it ?

    Read the article

  • Optimizing graphics for an iOS flash game

    - by 1GR3
    A friend of mine and myself are working on a flash developed iOS (and later Android) puzzle board game. He's a developer and I'm a designer/developer so (no surprise) we have different points of view. His method: make small tiles (100x100px) in Photoshop join them into the board and then in flash apply effects to the board to avoid repetition (80's not in the good way). My method: precompose the whole board (960x640px+bleed) in Photoshop and than mask active and inactive areas in flash. What do you think?

    Read the article

  • Import images from camera in KDE with particular directory structure

    - by Sergey
    I have been using f-spot for a few years to manage my photo archive, which is about 50K images at the moment. With the development of f-spot slowing down in the recent years and me switching to KDE, I'm looking at using DigiKam, which seems to be very nice and packed with features beyond my wildest hopes :) One thing I'm missing though is the way f-spot was importing the images: it was creating subdirectories based on the image's shooting date: $HOME/Photos/2011/11/12/IMG_1234.jpg $HOME/Photos/2011/11/13/IMG_1235.jpg $HOME/Photos/2011/11/13/IMG_1236.jpg I don't seem to be able to find a way to make DigiKam to behave like this - although it has some settings to change the image filename according to some mask which may include shooting date, I see now way to tell it to create sub-directories. Is there a way to make DigiKam to behave like this? Or, alternatively, what is a good program to import images from a camera and save them on disk in subdirectories according to their shooting date?

    Read the article

  • How to properly set up a network bridge using bridge-utils using wlan0 as the internet "source"?

    - by Miguel Azevedo
    Hey everyone this is my first post so go easy on me. I currently have a laptop with Ubuntu Studio 12.04 Beta 2 that is supplying a wireless internet connection to a windows 7 desktop computer that's connected directly to the laptop through Ethernet. I'm using the "shared to other computers" method in network manager but I believe it doesn't work with what I want to do. I would like to have the windows computer on the same subnet as every other computer in my house (192.168.1.x) so I can use LAN applications (MIDI over WiFi, Bonjour etc.) on the windows computer without having to run a massive cable to the router. I've been googling endlessly and tried multiple configurations in the /etc/network/interfaces file without success. All of them would report "cannot add wlan0 to bridge" Is there a specific way to make this work? What am I missing? Thank you

    Read the article

  • Can I remove visible referer from link?

    - by Andreas
    I use referer info to track which of my campaigns works the best. So instead of <a href="someweb.com">someweb</a> I have a link like <a href="http://someweb.com?utm_source=john&utm_medium=email&utm_content=NAME&utm_campaign=campaing">someweb</a> Now when a user cliks "someweb" the whole URL string is shown in the adressbar. Is this possible to mask/hide somehow? Maybe via .htaccss? Thanks in advance

    Read the article

  • Replace Broadcom "wl" driver with "b43"

    - by Laszlo Boros
    I'm using Ubuntu 10.04.4 LTS, and in my laptop there is a Broadcom BCM4312 wlan card. lspci output: 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) Subsystem: Broadcom Corporation Device 04b5 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f4500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 81-ac-1d-ff-ff-12-54-92 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, ssb So as you can see, the current (and default) driver is wl - installed with jockey. But I have another Ubuntu based distribution on my laptop (BackTrack linux), which is also 10.04, but it has the b43 driver installed and the overall performance is MUCH better. So I would like to install it on this OS too, but even google didn't help me. So my question is how to install the latest b43 driver on my Ubuntu?

    Read the article

  • URL masking with .htaccess

    - by Michael Nguyen
    I need a hardcore programmer to help me with URL masking. So this is my situation. My website www.michaelfotograf.dk/blog/ is the main site that needs to be configured. I have another website/webhotel called www.umagepar.dk www.umagepar.dk is redirected to www.michaelfotograf.dk/blog/ The blog is an ongoing project where i post a lot of stuff to get my ranking higher on google. www.umagepar.dk which redirect to www.michaelfotograf.dk/blog/ is also a project on is own, so I do not want people to know, that it is a blog connected with www.michaelfotograf.dk/blog/ I therefore need to mask www.michaelfotograf.dk/blog/ so it will be called www.umagepar.dk in the URL in the searchbar at all times! What I need is a programmer that can do this for me. Name your price, and I'll see if I can affort it. Michael

    Read the article

  • Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to get it to work?

    - by zewone
    I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686 ![Schizophrenic Ubuntu](http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) Any help much appreciated... Thanks, Philippe 31-10-2012 ... I have some more updates. When I do the following command it does see my Wifi router... So even if it is still disabled... the card seems to work and see the router (ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E") See below: sudo iwlist wlan1 scanning wlan1 Scan completed : Cell 01 - Address: 00:19:70:8F:B0:EA Channel:10 Frequency:2.457 GHz (Channel 10) Quality=51/70 Signal level=-59 dBm Encryption key:on ESSID:"5791BC26-CE9C-11D1-97BF-0000F81E" Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s Bit Rates:24 Mb/s; 36 Mb/s; 48 Mb/s; 54 Mb/s Mode:Master Extra:tsf=000000025dbf2188 Extra: Last beacon: 108ms ago IE: Unknown: 002035373931424332362D434539432D313144312D393742462D3030303046383145 IE: Unknown: 010882848B960C121824 IE: Unknown: 03010A IE: Unknown: 0706424520010D14 IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : CCMP TKIP Authentication Suites (1) : PSK IE: Unknown: 2A0100 IE: Unknown: 32043048606C IE: Unknown: DD180050F2020101030003A4000027A4000042435E0062322F00 IE: Unknown: DD0900037F01010000FF7F IE: Unknown: DD0A00037F04010000000000

    Read the article

< Previous Page | 39 40 41 42 43 44 45 46 47 48 49 50  | Next Page >