Search Results

Search found 2042 results on 82 pages for 'booting'.

Page 44/82 | < Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >

• HP ML350G6 running hyper-V 2008 r2 resets itself every 2 hours

  - by GT

  The system started resetting itself exactly every 2 hours. These are the messages in the iLO2 log: Informational iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server power restored. Caution iLO 2 03/07/2010 20:40 03/07/2010 20:40 1 Server reset. It's not an ASR reset (that would show in the log) Redundant power supplies, swapped but no change. Turned off all virtual machines (i.e. now only running hypervisor) but not OK Boot HP smartstart diagnostics disk, ALL OK Diagnostic disk reports no errors Went back to booting Hypervisor and the problem is back. Seems the hyper-V system disk has got a time based program (virus) causing the reset. I thought the hypervisor had a small attack surface and should be OK. All virtual machines (SBS2008, Win7 and Win XP) and network computers are protected with TrendMicro WFBS. I am about to rebuild the disk (I have backups) but wondered if there were any suggestions to try first???

  Read the article

• Windows Media Center says "Searching for tuners" when I try to play live TV

  - by Louis

  After upgrading from Windows 8 Pro with Media Center to the 8.1 preview, I need some help in being able to watch live TV again. When I try to now, it says Please Wait. Searching for tuners. I tried reinstalling the software for the Hauppauge WinTV DCR-2650 TV tuner, and upgrading the firmware for both the tuner and the Cisco STA-1520 tuning adapter. I also tried swapping around the USB ports, cold-booting the devices, and running the Set Up TV Signal setting in WMC, but that says The TV signal cannot be configured because a TV tuner was not detected. Both devices look fine in Device Manager, reporting the "This device is working properly" status. I'm not sure if this is related, but I did have some network connectivity issues immediately after upgrading to Windows 8.1 where my either my subnet mask or default gateway was missing, and since the TV tuner shows up as a network device, I wonder if that might be related. However, I really don't know how those settings should look and Hyper-V sort of further complicates things with the virtual Ethernet adapters:

  Read the article

• Can't boot from SATA dvd, seen as SerialCH1_Master

  - by dierre

  Here's the problem: I have an old computer based on an AsRock motherbord, the p4vt8+. I have 2 IDE HDs , one per each channel (IDE0 and IDE1) and I have a SATA dvd LG GH22N550. When I go into the BIOS panel on the boot devices list I can see IDE0 and IDE1 but not the dvd that I need to install Windows. When the computer is booting I can see it under the voice SerialCH1_Master. I know I'm doing something wrong but I can't figure out what it is.

  Read the article

• GDM Won't Automatically Start After Boot

  - by Mikey.B

  Ubuntu 10.04 Hi guys. I'm not sure why but quite recently, my ubuntu desktop started bringing up the command prompt login screen after booting. I want GDM to start up by default. I can manually bring up GDM by typing: sudo service gdm start or sudo /usr/sbin/gdm but I want something more permanent. The contents of /etc/X11/default-display-manager point to /usr/sbin/gdm The chkconfig status for GDM shows that it's off on all run levels... could that be it? I tried running: sudo chkconfig --add gdm and just got errors... Any ideas? How can I get GDM to automatically come up again? Any/all help is appreciated! -M

  Read the article

• Getting USB boot to work in SmartOS on HP ProLiant N40L

  - by user126579

  I recently downloaded SmartOS and tried running it on my HP ProLiant N40L, but it always fails on boot. After dd'ing the image to the USB stick, I plug it into the internal USB header and turn the machine on. After selecting from GRUB, it displays the following: , bss=0x0 It sits there for 2-4 minutes, then finally boots the OS and displays the following: WARNING: Couldn't read ACPI SRAT table from BIOS. lgrp support will be limited to one group. SunOS Release 5.11 Version joyent_20120614T184600Z 64-bit Copyright (c) 2010-2012, Joyent Inc. All rights reserved. WARNING: kvm: no hardware support After that, it hangs. I've tried this with two different USB sticks. I've seen some mentions on the SmartOS website about people running it on an N40L, booting from USB, so maybe it's just broken hardware? Has anyone gotten this working?

  Read the article

• Late 2008 Unibody MacBook Pro, Snow Leopard EFI 1.8 downgrade

  - by SiLo

  Question: Does anyone know of an EFI downgrade for user on 1.8? I have found a 1.7 to 1.6 downgrade, but once on 1.8 this downgrade no longer works. Background: After upgrading to Snow Leopard, and installing the EFI 1.8 update (as recommended by Software Update), I have lost the ability to burn discs. This also includes when using external burners and when booting into Vista using Bootcamp. Other seemingly related problems to the EFI I have are, chronic overheating, random temporary beachball lockups, longer boot times. These 'other' problems have been solved for other users who experienced these problems on EFI 1.7, but were able to rollback to 1.6. I am looking for a solution that does not require sending my computer back to Apple.

  Read the article

• Linux & Windows Boot Up Times in Amazon Web Service and Windows Azure

  - by Adron

  I've been working with Windows Azure and Amazon Web Services EC2 for a good many months now (almost getting to the years range) and I've seen something over and over that seems troubling. With AWS & Linux I commonly get instance startup times with EC2 around the 1-3 minute range. With AWS & Windows OS on an EC2 instance it often takes 10-20 minutes. With Windows Azure Web or Service Role I often get anywhere from 6-30 minutes waiting for a role to startup. I assume of course this involves booting up a windows instance somewhere in the fabric. I know there has always been tons of FUD about windows vs. Linux, but I'd really like to know why it is that Windows 08 or 03 boots so much slower in the cloud than Linux. Any specific technical information regarding this would be greatly appreciated! Thanks.

  Read the article

• Adaptec 2420SA RAID 1 rebuild 66% after 1 week

  - by moss

  We're running a 500GB RAID 1 on an Adaptec 2420SA - 2x500GB Hitachi Drives. It suddenly crashed and required a rebuild -- was not even booting. It's only at 66% after about a week. Very frustrated. This is the second box with the same card and drives that has had issues with the RAID/drives. Another box had this happen twice. Both machines are Linux boxes. CentOS and Fedora. I dunno if it's the firmware -- which currently needs an update (any help doing this over PXE would be great- I have used UDA to do PXE boots in the past). Anyway, would love to hear about experiences with this card and firmware. I thinking of going google and just using cheap boxes no raid and have server redundancy instead.

  Read the article

• Vertex 2 SSD is running faster than my Vertex 3 SSD?

  - by Kairan

  I used Acronis Disk Director to do a direct clone of my C:\ windows 7 x64 drive from my Vertex 2 to my new Vertex 3 SSD (Just to show the drive software winstall everything is identical.) I ran a performance test on Windows using the Windows Experience Index. The rating I am receiving when booting on the Vertex 2 is 7.5 While I am getting only a rating for the Vertex 3 of 6.9 My understanding is that the read/write speeds of the Vertex 2 is only up to 250MB/sec while the Vertex 3 is up to 500MB/sec. Copying a single file (3GB in size) from the Vertex 3 to itself was getting speed of approx 70-80MB/sec This speed is no better (maybe worse) than what I got from the Vertex 2 I am connected via the SATA 3 port on the motherboard, using an SATA 3 cable Is this issue caused by the drive cloning? Do I have a bad SSD?

  Read the article

• How to remove Ahnlab policy agent?

  - by R.K.

  Anybody know how to remove the Ahnlab Policy agent? I was forced to install it so that I could connect to the campus network when I visited Korea. Now that I'm home, I would like to remove it. However, it resists all uninstallation efforts. It gives me an Access is denied error whenever I try to stop the service. Used AppRemover too, to no avail. Tried removing it in safe mode but it doesn't work either. Does anybody know of a solution short of booting up a Linux distro and deleting the Ahnlab files with it?

  Read the article

• Acer Aspire 1360 Recovery CDs

  - by John

  I have replaced a dead hard disk in an out of warranty Acer Apire 1360 laptop. The two recovery CDs I have dont appear to be bootable, they just contain .hdd and .ghs (image?) files. On the original broken hard drive there was a hidden partition which could be invoked by pressing alt+f10 when booting. You would then be prompted for the 2 recovery CDs to perform the restore. Obviously the new hard drive does not contain the hidden Acer recovery partition. This being the case, how do I go about restoring Win XP? The 2 CDs are called Aspire 1360/1520 Serires Recovery CD Disk 1 of 2 and 2 of 2. Am I missing a futher bootable recovery CD? Can anyone confirm how many restore CDs originally came with the laptop.

  Read the article

• Problems with kickstart script, partition info crashes deployment

  - by tore-

  Hi, Currently testing cobbler, but have problem with the kickstart script when the partition information is loaded. Here is my ks: http://pastebin.ca/1824343 I can't figure out what is the problem with the partsection at all. Without it, it works. I've even tried autopart. If the entry is removed, it works, but of course I have to provide the installer with partition information. Under the kickstart an python exception is raised. I get a Errno 2 No such file or directory. My Apache logs states: File does not exist: /var/www/cobbler/links/CentOS-5.3-x86_64/images/updates.img File does not exist: /var/www/cobbler/links/CentOS-5.3-x86_64/disc1 File does not exist: /var/www/cobbler/links/CentOS-5.3-x86_64/images/product.img But without the part information, no error occours. What am I not seeing? Cobbler 2.0.3, imported the CentOS 5.3 x86_64 DVD, PXE booting from a Xen guest.

  Read the article

• Fedora 12 How to Force a Display to Load on Boot even when no Monitor is Attached

  - by key

  When booting Fedora 12 with no monitor connected, if I connect a monitor later it gives a no signal error. I think it is set to auto-detect if a monitor is connected or not and load a display based of that. Since it initially detects no monitor no display is loaded. What I would like to do is have it act as if a monitor was always connected and provide the display signal always. I don't know if this is the issue or not but if you know how I might be able to fix this issue so that I can connect a monitor whenever I feel like it without having to restart that would be best. Thanks for the help! :D

  Read the article

• just curious if anybody every tried this- hyper-v r2

  - by tony roth

  I have a server that san boots that I want to p2v. I have many options disk2vhd, scvmm etc but I was thinking about cloning the lun (flexclone, netapp) presenting it to my hyper-v r2 server. Within the hv manager do a create new disk then have it copy the cloned lun to a vhd file. Then do the bcdedit\bootsect stuff to it. Should work right? I'm also curious if anybodys booting vhd's that are on bootable luns? I've booted native vhd's just fine was just curious about the running them off a bootable lun. I think that this has quite a few advantages like instant p2v etc.. any thoughts on this? hmm dang as I was typing this I realized that I should not use the hv manager new disk copy routine, I should just disk2vhd the mounted lun. This has advantages in that it should be a lot faster!! thanks

  Read the article

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess. (Edit - One extra thing that may or may not be relevant: it's the 64 bit version of Server 2008 R2)

  Read the article

• ubuntu 9.10 screen flickering problem on Thinkpad R31 with Intel 83830 Graphics

  - by PA

  I am trying to revitalize an old Thinkpad R31 that has the Intel 82830 graphics and only 256 MB of RAM. I have tried a Xubuntu 9.10 Live CD. After booting the screen blinks so much that it is practically unreadable. I have searched for updated IBM Thinkpad drivers but I only found drivers for Windows on the Thinkpad support web site. EDIT: I have changed the title and the description. It is not a problem of the drivers. It seems to be a problem with the kernel. See my own answer below.

  Read the article

• Xenserver boot error

  - by Adrian

  I'm trying to get Xenserver 5.5 running on a spare computer here, hardware specs: Intel Q6600, 4GB Ram, and Gigabyte GA-P35-DS3R motherboard Xenserver itself installs fine onto a 150GB sata hdd, however it fails to boot whatsoever, giving this garbled mess: http://img697.imageshack.us/img697/9918/biosi.jpg it's not frozen because if I press enter it just prints a different garble and it also says "could not find kernel image". The strangest thing is if I put that hdd in my desktop and assign it to a VMWare desktop vm (under the ESX profile no less) it boots perfectly... leading me to believe there are no problems with the install or the hdd itself. From what I can tell the error seems to be occuring completely seperately to Xenserver, in the bootloader extlinux?. If there was a motherboard compatibility issue I would think it would also have manifested during installation, and the fact the problem seems to be with the booting into Xen makes me doubt this. Any ideas guys? (I'm using Xen because it can do PCI passthrough without VT-d.)

  Read the article

• How do I get Windows 7 To Recognize a newly installed RAID 5 volume?

  - by GregH

  I had a previously running Windows 7 (64 bit) system. I added 3 new 1TB Seagate drives that I set up as a RAID 5 volume. I have a Gigabyte GA-P55M-UD2 motherboard. I installed the drives, set up the BIOS and configured the three drives as a RAID volume through the RAID setup utility that was accessed via Ctrl-I while the system was booting. I rebooted the system and could see the drives during the boot sequence. However, when Windows 7 was starting I got an error (quick blue screen) and then Windows tried to repair itself with no success. Do I need to install RAID drivers in Windows? How do I do it if Windows won't boot? Thanks in advance.

  Read the article

• Adobe Master Collection CS3 wont run on my Windows 7 64bit

  - by Jeremy

  I have a brand new HP p6230y. My first step after booting it up was to install Master Collection. It installs fine, but when I go to run each of the applications, and they all behave differently. I have re-installed twice already. Photoshop opens, but freezes. Acrobat tells me that I need to reinstall. Nothing else even opens (no freezing, no process in taskman). Any Ideas? HP p6230y RAM: 8gigs CPU: AMD Phenom2 x4 810 (2.6ghz) OS: Windows 7 Home Ultimate 64bit

  Read the article

• What is the difference betweeen "Network install" and "Network Boot" options in virt-manager when installing a new virtual machine

  - by Marwan

  From my understanding of PXE (Preboot Execution Environment), I know that there must be some negotiation first between the booting client and a DHCP server to obtain network parameters (IP address, etc) in order for the client to be able to fetch the boot loader and kernel image from the boot server. In other words, and aside from being a "virtual" machine, we're talking here about a "bare metal" machine, so there must be some "pre boot" mechanism for those negotiations to take place, and this is exactly what PXE is all about. When I think about the "Network install" option, I can't figure out how the new VM would be able to fetch the boot images (bootloader and kernel) without the previously mentioned mechanism. So, here is a short version of the question: When provisioning a new virtul machine, how do you expect the "Network install" option in virt-manager to work behind the scenes? Many thanks.

  Read the article

• Beeping Hard Disk - Seagate 250GB Momentus 5400.6

  - by Pez Cuckow

  I have been trying to repair a laptop that simply beeps instead of booting. After taking it apart I have now realised that it is the hard disk beeping. I know that may sound strange but I guarantee that is what it is! (Currently powered on it's own with a Sata Mains lead). The beeping is slightly faster than one per second there is a link to this recording. This recording was made resting the mic on the hard disk while it was sat on a table on it's own, there are no speakers anywhere near, the sound is coming from the hard disk. Does anyone know what this beep means? Is the hard drive just dead, or is it fixable and the data recoverable? Many thanks,

  Read the article

• Ext3 partition doesn't mount on Snow Leopard using MacFUSE

  - by Fez

  I'm dual-booting OS X and Ubuntu on a Macbook 4,1. I'm trying to mount my Linux partition in OS X. I installed MacFUSE 2.0.3,2 and fuse-ext2-0.0.7 on Snow Leopard 10.6.5. I created the directory /Volumes/Ubuntu and tried to mount the disk there using the command: fuse-ext2 /dev/disk0s4 /Volumes/Ubuntu/ This is the output I get: fuse-ext2: version:'0.0.7', fuse_version:'27' [main (../../fuse-ext2/fuse-ext2.c:324)] fuse-ext2: enter [do_probe (../../fuse-ext2/do_probe.c:30)] fuse-ext2: Error while trying to open /dev/disk0s4 (rc=13) [do_probe (../../fuse-ext2/do_probe.c:34)] fuse-ext2: Probe failed [main (../../fuse-ext2/fuse-ext2.c:340)] Any clue what's going wrong? Thanks!

  Read the article

• Ubuntu only boots with USB plugged in

  - by Ben

  I'm new to the Linux world so please bear with me! :-) I installed Ubuntu via USB drive onto my hard drive. If I boot the PC without the usb drive I used, Ubuntu will not load. After booting I can unplug without any consequences. I looked on the hard drive and there is a boot folder. On the USB drive, this is the tree contents: /media/disk$ tree . |-- adtext.cfg |-- boot.cat |-- f10.txt |-- f1.txt |-- f2.txt |-- f3.txt |-- f4.txt |-- f5.txt |-- f6.txt |-- f7.txt |-- f8.txt |-- f9.txt |-- initrd.gz |-- isolinux.bin |-- isolinux.cfg |-- ldlinux.sys |-- linux |-- menu.c32 |-- menu.cfg |-- po4a.cfg |-- prompt.cfg |-- splash.png |-- stdmenu.cfg |-- syslinux.cfg |-- text.cfg |-- ubnfilel.txt |-- ubnpathl.txt `-- vesamenu.c32 Am I correct in my assumption that the boot aspect is associated to the USB drive? If so, how do I get it to boot without the USB? I'm guessing copying into some location and modifying grub?

  Read the article

• Disable laptop screen

  - by Kyle

  I recently had the display fail on my Dell Inspiron E1505 laptop. I currently have my TV hooked up to the laptop's S-Video out which works fine as long as I'm running in Windows. For the first minute or so when the computer is booting I get no display. I was wondering if there was any way to disable the laptop screen entirely so that the TV display is active from the beginning (not just after Windows loads). I realize there may be a BIOS setting for this, my only problem is I can't see the BIOS settings screen since no display is active at that point so if anyone has any BIOS setting solutions I'd need the exact keystrokes to hit :)

  Read the article

• Merging partitions and removing windows of one partition

  - by SmartLemon

  I have two partitions on my laptop, I created a new one when installing windows 8 pro because windows 7 wouldn't upgrade to it for some odd reason. The main partition, which has 631 GB ( has windows 7 installed on it, and the second partition is 49.9 GB and has windows 8 installed on it. What I need to do is remove windows 7 from the other one (Yeah its dual booting), make it so it boots straight into windows 8, without showing the dual boot screen, and also merge the two drives together. Only problem is, I have no idea how to do this. Please don't use complete lamens terms, I am a software developer so I know at least a bit about computers. Here's disk management so you can see how its set out.

  Read the article

< Previous Page | 40 41 42 43 44 45 46 47 48 49 50 51  | Next Page >