Search Results

Search found 3112 results on 125 pages for 'webforms routing'.

Page 46/125 | < Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >

• second ip address on the same interface but on a different subnet

  - by fptstl

  Is it possible in CentOS 5.7 64bit to have a second IP address on one interface (eg. eth0) - alias interface configuration - in a different subnet? Here is the original config for eth0 more etc/sysconfig/network-scripts/ifcfg-eth0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0 BOOTPROTO=static BROADCAST=192.168.91.255 HWADDR=00:1D:09:FE:DA:04 IPADDR=192.168.91.250 NETMASK=255.255.255.0 NETWORK=192.168.91.0 ONBOOT=yes And here is the config for eth0:0 more etc/sysconfig/network-scripts/ifcfg-eth0:0 # Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express DEVICE=eth0:0 BOOTPROTO=static BROADCAST=10.10.191.255 DNS1=10.10.15.161 DNS2=10.10.18.36 GATEWAY=10.10.191.254 HWADDR=00:1D:09:FE:DA:04 IPADDR=10.10.191.210 NETMASK=255.255.255.0 NETWORK=10.39.191.0 ONPARENT=yes How would the resolv.conf file should change since there are two different gateways? Any other change needed?

  Read the article

• How to access an IP address as if on a different network using SSH

  - by NT3RP

  In preparation for a lengthy business trip, I set up my router such that I can access my home computer over the internet via port forwarding over SSH. One thing I neglected to do was setup access to my router remotely. Normally, I can just access the router configuration page via 192.168.1.1. I know that it's possible to tunnel traffic through SSH, but how do I access an IP address as if I were on my home network using SSH?

  Read the article

• How to set up DHCP-configured access through a Linux box?

  - by marcusw

  I would like an old desktop box to use my laptop as a router to access the internet. Here is my setup: I have one ethernet port in the side of my laptop which I want to use to get internet access to my desktop computer. The laptop is connected to the LAN via a wireless link. Both systems run Linux. The desktop autoconfigures itself using DHCP. The laptop is a Kubuntu system. I do not have any crossover cables, though wireshark on the laptop sees the DHCP requests from the desktop just fine, so I doubt that I need one. What do I have to do to make this work?

  Read the article

• How to route HyperV VMs traffic through host VPN

  - by Random

  I'm using Windows 8.1 Pro with HyperV. I have several VMs for development, all of them connected with host via Internal adapter using network addresses: 192.168.10.0/24 Where: 192.168.10.1 is my host's Hyper-V internal NIC address. When I'm not in my office I use 3G usb dongle an dialup VPN connection. I would like to route traffic from all existing and future VMs through the VPN. In best scenario traffic would be routed only partially to the local company network addresses 10.1.1.0/24 I don't want to use sharing because I'm switching between WiFi, USB 3G dongle and VPN. Moving to other virtualization is also not an option for me.

  Read the article

• Split horizon, route filtering, and having RIPv2 announce a non-attached route to host...

  - by Paul

  Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

  Read the article

• BGP path prepended route not listed anywhere

  - by Julien Vehent

  We have a simple multi-homed setup with two routers that advertise our AS to two ISP. The second ISP (ISP B) is only used for backup when ISP A goes down, so we prepended our AS 3 times on this route. I spend a couple of hours this morning poking at looking glass routers all over the internet, and none of them list our backup route with the prepended path. I checked the south african internet exchange, the london internet exchange, oregon internet exchange and a couple dozen ISPs. All of them have multiples routes through ISP A, often with 3 or 4 hops. The route through ISP B should, at least, appear somewhere and have 5 or 6 hops. But I couldn't find it anywhere. (I checked the full bgp tables on the looking glass routers, using show ip bgp 65000) My questions are: Is there a limit to the size of a route after which most routers will simply discard the route ? Is our backup route even going to work when ISP A goes down, if no router knows about it ? Our two routers are connected on iBGP. Would it be possible that the route through ISPB is not announced because the iBGP session prefers the route through ISPA ? This is what non-exist-map and advertise-map are supposed to do, but none of those are used in either routers.

  Read the article

• Difference between "traceroute" and "traceroute -U"

  - by AndiDog

  The manpage of traceroute says that the "-U" parameter (UDP probing) is the default, but I'm getting different results every time. With "-U": traceroute -U www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 13 rap-vl165-te3-2-jussieu-rtr-021.noc.renater.fr (193.51.181.101) 59.445 ms 56.924 ms 56.651 ms [...] 18 * paris1web.univ-paris1.fr (193.55.96.121) 23.797 ms 23.603 ms but the normal traceroute gives me another result (never reaches the final node) - it's either "!X" or just exits after the maximum of 30 hops: traceroute www.univ-paris1.fr traceroute to www.univ-paris1.fr (193.55.96.121), 30 hops max, 60 byte packets [...] 11 te1-1-paris1-rtr-021.noc.renater.fr (193.51.189.38) 28.147 ms 28.250 ms 28.538 ms [... non-responding nodes ...] 28 site-1.03-jussieu.rap.prd.fr (195.221.126.58) 85.941 ms !X * * Note: I tried this very often and always get the same results. The path in my local network is always the same. So what does the "-U" parameter actually change here? I'm especially interested what the reason for "!X" could be (communication administratively prohibited). EDIT: If that helps, paris-traceroute gives me the following for the last hop: 14 P(1, 6) site-1.03-jussieu.rap.prd.fr (195.221.126.58) 34.938 ms !5 !T2 which means that node discards the packet with TTL=2 and returns an unknown message (not "destination unreachable" or the like).

  Read the article

• Trouble opening my router to my web server [closed]

  - by justin

  Here's the story. I have a webs server created and connected to my router. The website works great when I'm connected to the router, but when I'm off the network I can't access the website. I got the IP for my router by googling "what is my ip." I have opened ports 80 to 10080 to link to the server in the router. THe firewall is off. I can ping the router. One odd thing that I don't understand. When I am in network if I access XXX.XXX.XX.XX:80 I can access the web page no problem. If I access XXX.XXX.XX.XX:81 (or any other port) I get the error "Cannot access server." Any idea what the problem could be? Could it be my ISP?

  Read the article

• How do I configure custom routes when an interface is configured?

  - by ManicDee

  Other Superuser questions have addressed the issue of adding custom routes to access e.g.: multiple networks of a corporate network through one interface, while accessing the Internet through another interface. So assuming that I have a script to add specific routes when en0 is configured, and a separate script to add specific routes when en1 is configured, is there some way I can trigger those scripts to run automatically when Mac OS X/Darwin starts and configures those interfaces? Back in my Linux days, it was possible to add an option in /etc/network/interfaces along the lines of: iface eth0 inet dhcp up /usr/local/sbin/eth0-routes-up Is there something similar for Mac OS X?

  Read the article

• PFSENSE and IPV6 , direct connect rules

  - by Bgnt44

  My question is about pfsense configuration for ipv6 In theory Ipv6 are fully routable even in a LAN For stating point i ve Using this tutorial : http://doc.pfsense.org/index.php/Using_IPv6_on_2.1_with_a_Tunnel_Broker So my Lan network has ipv4 connection and ipv6 I would like to be able to access my LAN machines by their IPV6 i'm confused with firewall rules which i need to set to be able to do that Even if i set all interfaces to pass all packets, i'm not able to directly access any machine by their IPV6 Did i miss something ? Edit : Ok i found that it work now, think it has always work but my isp seems to support ipv6 sometimes and sometimes not ... weird

  Read the article

• Connectiong adsl router/modem and router with bridgemode

  - by Zvonko Telefonko

  I have one adsl modem/router which is not "top" of the line and it lack allot of options which I need. I was able to acquire one Cisco router recently which has all options that I need ( like DMZ, VPN, port forwarding, etc). I'm interested, if I connect the old modem/router to new Cisco router using bridge mode, will I be able to use all the features on the Cisco? For instance, the old router is lacking of port forward options. Does this mean that I will not be able to use port forwarding on Cisco router either or, since I will be using bridge mode, this will not affect Cisco router and it will work as the modem is in him? thank you

  Read the article

• Providing reverse records for records that map to ISP IP

  - by thejartender

  I have been instructed to use my ISP ip (as a temporary fix for mapping my name server and domain records as my router dishes out rfc 1918 adresses to devices in my network where I am running an Ubuntu server, my router and my development laptop andso I have fixed: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 10.0.0.42 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 10.0.0.42 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. To a temporary version of: $TTL 3H @ IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); thejarbar.org. IN A 88.89.190.171 @ IN NS ns.thejarbar.org. yuccalaptop IN A 10.0.0.19 ns IN A 88.89.190.171 gw IN A 10.0.0.138 www IN CNAME thejarbar.org. I am using bind and when using named-checkzone on this file according to my zone configurations, this file has no errors. I then run dig thejarbar.org @88.89.190.171 and get an expected authorative reply. My issue is creating my reverse DNS SOA zone and I would gratly appreciate assistance and guidance. I am stuck on how to represent the reverse records correctly for the eddresses that map to my isp IP. I am trying: $TTL 3H 0.0.10.in-addr.arpa. IN SOA ns.thejarbar.org. email. ( 13112012 28800 3600 604800 38400 ); 171.190.89.88. IN PTR thejarbar.org. 171.190.89.88. IN NS ns.thejarbar.org. 19 IN PTR yuccalaptop.thejarbar.org. 138 IN PTR gw.thejarbar.org. www IN PTR www.thejarbar.org. But running named-checkzone on this file leaves an erroneous return that IN: has no NS records I would greatly appreciate assistance

  Read the article

• How does ospf control flooding?

  - by iamrohitbanga

  What method is used by ospf protocol to prevent looping of flooded packets for link state advertisements? The packet header does not contain any timestamp. How do the routers recognize that it is the same advertisement that they sent before?

  Read the article

• static routes, cisco ASA, remote locations

  - by Jeff

  192.168.3.1(ASA) - 192.168.2.1(ASA) - ( internet ) - 192.168.1.1(ASA) DomainController, FS, Exchange 192.168.0.1(ASA) - above is a rough idea what my network setup looks like. each internal ip (192.168.x.x) is located behind an ASA. Each location has a different gateway for the internet. They all talk to the 192.168.1.1 network for dns, dhcp, dc, exchange and so on. They can only see the 192.168.1.1, they can not see each other. In my Static Routes on my 192.168.1.1 ASA, should i have them configure as follows? example: 192.168.x.x 255.255.255.0 Locations_Internet_Gateway_IP OR 192.168.x.x 255.255.255.0 Main_Locations_Internet_Gateway_IP not sure which configurtation is correct, thanks in advance for any help!

  Read the article

• How to set the preferred network interface in linux

  - by Mike Cooper

  I have my network set up like this. http://docs.google.com/Doc?docid=0AZ1YxuLE4djaZGhqN2s1NmRfMjhjNjc0Ym1meg&hl=en In words: I have a machine (Calcium, running Arch Linux) that has two network interfaces. eth0 is hoooked up to a router, and is gigabit. Eth1 is hooked up directly to the university network over 10Megabit. The router's uplink is hooked up to the university network as well, and it is also 10Megabit. Currently (I believe) all traffic on Calcium is going through eth0, through the router, regardless of whether it is internal or external. (How can I confirm this?) Ideally, traffic that is destined for the internal network (192.168.10.0/24) would travel over eth0 to the router, and wherever it is going. ALL other traffic should go over eth1.

  Read the article

• Netstat flags on OS/2

  - by Cian

  On an OS/2 box, what do the flags UGDP mean in the output of netstat -r. Google seems to point to them meaning Up, Gateway (i.e. an indirect root), and Dynamic (learned from a redirect), but that leaves me mystified as to the meaning of P. The only suggestion I've had is permanent but that doesn't make any sense with dynamic. Any ideas?

  Read the article

• Centos 6.2 Fresh 'Basic Server' install networking issues

  - by RWC

  I've had a /29 provisioned on a network port for a server and am trying to at least configure the machine so I can ssh into it. It's Centos 6.2 x64 with the Basic Server install. Currently not able to ping gateway or any address for that matter. For reference: Default Interface: em2 Network ID: 66.*.*.0/29 Gateway: 66.*.*.1 Broadcast: 66.*.*.7 Please see my following configs: /etc/sysconfig/network-scripts/ifcfg-em2 DEVICE=em2 NM_CONTROLLED=yes ONBOOT=yes HWADDR=Not Important TYPE=Ethernet BOOTPROTO=none IPADDR=66.*.*.2 PREFIX=29 DNS1=8.8.8.8 DNS2=8.8.4.4 DEFROUTE=yes IPV4_FAILURE_FATAL=yes IPV6INIT=no NAME="System em2" NETMASK=255.255.255.248 USERCTL=no $: route -n Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 0.0.0.0 255.255.255.248 U 0 0 0 em2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 1003 0 em2 0.0.0.0 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: route Destination // Gateway // Genmask // Flags // Metric // Ref // Use // Iface 66.*.*.0 * 255.255.255.248 U 0 0 0 em2 link-local * 255.255.0.0 U 0 1003 0 em2 default 66.*.*.1 0.0.0.0 UG 0 0 0 em2 $: cat /etc/sysconfig/network NETWORKING=yes HOSTNAME=excalibur.domain.com GATEWAY=66.*.*.1 Keep in mind that I cannot even currently ping the gateway which is quite confusing for me. My /etc/hosts are configured correctly with the *.2 address. I'm not concerned with getting all of the addresses on the /29 up and running yet, just one so I can at least ssh in. Thanks! Edit: Adding in ifconfig. $: ifconfig em2 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX inet addr:66.*.*.2 Bcat:66.*.*.7 Mask:255.255.255.248 inet6 addr: UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5536 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2599469 (2.4 MiB) TX bytes: 748 (748.0 b) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:34 errors:0 etc etc

  Read the article

• Correct way to set up office network - 8 workstations, a file server and a staging server

  - by naunu

  Our office had this old school windows 2003 domain setup, our server caught fire, and now we are looking to do it right from scratch. Here is what we need: 5 PC and 3 Mac workstations for web development, they will each have WAMP/MAMP setup on them, managed by their developers. We will have a file server for assets, and a LAMP server with an external IP for staging. Here is what we have to work with: 5 IP addresses, brand new PC file server with windows 2008 SE, D-Link DSS-16+ 16 port switch, belkin 5 port wireless router, cable modem with 4 ports. How I have it set up now (this is a temporary makeshift setup): Cable modem = LAMP server, wireless router Wireless router = Switch = All of the workstations and file server (setup as a workgroup). We have noticed our internet is very slow with us all plugged in to the switch, and the switch plugged in to the router. I am not positive, but I think it is because our router does not have NAT. We are also having problems with the MACs connection to the network drive - it keeps disconnecting. I want this done right, and we have a ~$600 budget to buy anything else we need. Does anybody have any advice for me? Should I set up a domain or workgroup?

  Read the article

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• How do I bridge connections in windows 7?

  - by Wolfgang Haak

  At work, our ISP has gone down, 3 days running. A company next door has kindly provided us with access to their wireless network, and I'd like to get our internal mail server (win 7) to become online via that wireless connection, while being accessible from within the LAN, but I'm struggling with the windows configuration. Our company's LAN subnet (wired interface) sits on 192.168.0. Neighbour's wireless subnet 192.168.1. I've tried bridging the connections but that disconnects the mail server from the Internet connection and the LAN. what do I have to do achieve this networking configuration? Kind regards, Wolfgang

  Read the article

• Route traffic from one VPN to a second VPN

  - by Dominic

  I have set up an OpenVPN server on my windows 7 64-bit PC. I also have a subscription to a VPN service. My aim is to be able to connect my android phone to the VPN server on my PC, and then route all traffic through the VPN service. I have a NetGear WPN824 router. I can get it working if I my phone is on my local network. Then I can connect my phone to the VPN server using the local IP address of my PC. In Network Connection in the control panel, I share the connection used by the VPN service with the connection used by the VPN server. Then when I browse the internet on my phone, all traffic goes through the VPN service. Very nice. But if my phone is outside my local network, so I have to connect my phone to the local VPN using my PC's external IP address, then this method doesn't work. If I connect my PC to the VPN service and then try to connect my phone to my own VPN, it just doesn't connect (the initial TLS handshake times out). If I connect my phone to the local VPN first, then this connection is lost as soon as I connect my PC to the VPN service. Does anybody know how I can get this working? Many thanks Dominic

  Read the article

• Best practice for assigning private IP ranges?

  - by Tauren

  Is it common practice to use certain private IP address ranges for certain purposes? I'm starting to look into setting up virtualization systems and storage servers. Each system has two NICs, one for public network access, and one for internal management and storage access. Is it common for businesses to use certain ranges for certain purposes? If so, what are these ranges and purposes? Or does everyone do it differently? I just don't want to do it completely differently from what is standard practice in order to simplify things for new hires, etc.

  Read the article

• Let vmware virtual machine connect to the world thru specialized interface

  - by flybywire

  I have vmware player, and I am running a special OS therein. My computer has two network interfaces, let's call them eth0 and eth1. I want to configure my computer so that all network traffic goes eth0 if and only if it originates in my virtual machine. If traffic belongs to my host OS then I want it to go thru eth1.

  Read the article

• How to route traffic from a subnet 10.0.0.x to a network 200.208.88.17

  - by Guilherme Longo

  I have the following configuration Router : IP: 200.208.88.17 (Internet) MASK: 255.255.255.40 Server 2003 : IP: 10.0.0.1 (with dhcp server ativated) dhcp scope: 10.0.0.11 - 10.0.0.254 MASK: 255.255.255.0 clients : IP: 10.0.0.11 - 10.0.0.254 MASK: 255.255.255.0 At this point I have all computer set-up in one switch. All clients are receiving ip´s from the dhcp server. I need to enable the internet in every client. I am not sure how to route the traffic from the clients to the router that is providing internet access. Could you please point me to the right direction?

  Read the article

• Avoid corporate blocked URL's when on Cisco VPN

  - by Marcus

  When I'm on my home PC and on my company VPN I can't get to sites that my company blocks. Is there a way to get around this? Why do my requests to facebook.com go through the VPN? Can you configure your system to, for instance, not go through the VPN for HTTP traffic? Update: We are using Cisco VPN v 5, I'm running on XP

  Read the article

< Previous Page | 42 43 44 45 46 47 48 49 50 51 52 53  | Next Page >