Search Results

Search found 33182 results on 1328 pages for 'linux port'.

Page 462/1328 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• How do you persist installed software & configurations on an Amazon EC2 instance?

  - by Richard

  I've gotten a base Debian AMI up and running and now I need to know the best way to maintain it. I've ran the updates (aptitude update/upgrade) and installed/configured my software (Apache, Ruby, etc.) but if I reboot the instance or start a new one I'll have to do all this work over again. How do you persist these types of things over a reboot? Do you build a new AMI every time you adjust some tiny piece of the system? Or is there some way to feed it a script on startup that configures it in "real-time"? I know I could go all the way with a Reductive Labs Puppet style setup but that's a bit too much for my needs right now (1-2 servers). Any best practices on this? Update: I found a bit of information on using User-Data to run scripts at instance boot time.

  Read the article

• Can a named (bind) crash make a server unreachable?

  - by giorgio79

  My server recently became unreachable, and after restart a named error was the last line I found in /var/log/messages before restart: Jun 26 00:15:06 host named[1303]: error (network unreachable) resolving 'dlv.isc.org/DNSKEY/IN': 2001:500:71::29#53 Jun 26 06:38:55 host kernel: imklog 5.8.10, log source = /proc/kmsg started. Jun 26 06:38:55 host rsyslogd: [origin software="rsyslogd" swVersion="5.8.10" x-pid="1294" x-info="http://www.rsyslog.com"] start Jun 26 06:38:55 host kernel: Initializing cgroup subsys cpuset Can a named crash make a server unreachable? I doubt it, as I assume I should still be able to login with ssh via IP, but the server did not respond...So, I am trying to make heavy guesses here.

  Read the article

• Samba does not reload user group members

  - by xato

  I am running a simple samba server setup where users connect to a share which contains folders for specific user groups. The folders are chmod 2770, so only users which are in the correct group can read/write in them. The problem is that if I change group memberships (i.e. remove user from group / add user to group; changes are in sync between clients and server!) samba does not automatically reload the group memberships for the user, so they can still write to groups that they are no longer a member of etc. I either have to reconnect to the share or to restart samba to apply the changes. Is there any way to prevent group caching and/or enable group membership reload in samba? My smb.conf: https://gist.github.com/anonymous/ca7c10a3b3e2168d7a03

  Read the article

• mongod fork vs nohup

  - by Daniel Kitachewsky

  I'm currently writing process management software. One package we use is mongo. Is there any difference between launching mongo with mongod --fork --logpath=/my/path/mongo.log and nohup mongod >> /my/path/mongo.log 2>&1 < /dev/null & ? My first thought was that --fork could spawn more processes and/or threads, and I was suggested that --fork could be useful for changing the effective user (downgrading privileges). But we run all under the same user (process manager and mongod), so is there any other difference? Thank you

  Read the article

• Optimal dir strcuture for keeping millions of files on an ext4 system

  - by Alex Flo

  I need to keep millions of files on an ext4 system. I understand that having a structure with multiple subdirectories is the general accepted solution. I wonder what would be the optimal approach in terms of number of dirs/subdirs. For example I tried a structure like 16/16/16/16 (that is, (sub)directories from 1 to 16) and I found that I am able to move 100K files to this structure in 2m50s. When trying to move 100K files to a 8/8/8/8/8/8 structure it took 11 minutes. So the 16/16/16/16 approach seems to be better but I was wondering if anyone has some empirical experience with an even better dir/subdir distribution.

  Read the article

• Can't compile software from source while attached to screen session.

  - by spams

  When I'm attached to screen session software doesn't compile with error message that it can't find some subdirectory (that exists) under directory structure of extracted tarball. When I detach from screen session and try to compile same software it compiles without errors. What could be wrong?

  Read the article

• System time is off in Fedora

  - by NoClue

  I have a desktop PC with Fedora, Ubuntu and Windows installed and grub used for multibooting. But time in Fedora is always 5 hours behind. If I change the time in Fedora, then Windows and Ubuntu will be 5 hours ahead of the current time. I don't understand how to fix it. Any ideas? All the timezone settings in Fedora, Ubuntu and Windows are the same.

  Read the article

• Skip kernel module at boot

  - by Gris

  Hello. There is a broken kernel module, due to which I can not even load the OS, so I can not delete or fix it. Is it possible to skip this module at boot, using the kernel's parameters or something? Thanks.

  Read the article

• Server suddenly running out of entropy

  - by Creshal

  Since a reboot yesterday, one of our virtual servers (Debian Lenny, virtualized with Xen) is constantly running out of entropy, leading to timeouts etc. when trying to connect over SSH / TLS-enabled protocols. Is there any way to check which process(es) is(/are) eating up all the entropy? Edit: What I tried: Adding additional entropy sources: time_entropyd, rng-tools feeding urandom back into random, pseudorandom file accesses – netted about 1 MiB additional entropy per second, problems still persisted Checking for unusual activity via lsof, netstat and tcpdump – nothing. No noticeable load or anything Stopping daemons, restarting permanent sessions, rebooting the entire VM – no change in behaviour What in the end worked: Waiting. Since about yesterday noon, there are no connection problems anymore. Entropy is still somewhat low (128 Bytes peak), but TLS/SSH sessions have no noticeable delay anymore. I'm slowly switching our clients back to TLS (all five of them!), but I don't expect any change in behavior now.

  Read the article

• Out Of Memory Error - Magento

  - by robobobobo

  Ok normally I understand when my server is giving me out of memory errors, but this one has me stumped! I'm running a magento based site, with one or two plugins in it and the rest is pretty basic. The site runs and loads fine wiht no issues. However in the backend - Configuration - Payment Methods it gives me the following out of memory error Fatal error: Out of memory (allocated 39059456) (tried to allocate 85 bytes) in ########/Varien/Simplexml/Element.php on line 84 Now this is where I'm confused..it's allocated more than it tried to allocate? Am I correct there? So how is it running out of memory? My server has 6Gb ram, an SSD and 2 CPU's running WHM with a few other low traffic sites on it. I set my php memory limit to 100mb, 1000mb and finally unlimited but all to no avail! I'm completely lost here, would really appreciate some expertise on this Cheers

  Read the article

• Still no external sound after installing ubuntu 10.04

  - by Walter

  As suggested I upgraded. Same as before except now not even the speaker control in the application bar. Please help. Background: I have Ubuntu 9.10. Headphones appear to work fine. External speakers - nothing. There are so many sound preferences I have no idea what or which combination. Went to terminal and ran alsamixer which seems to recognize my sound card, though the driver is not listed in System Administration Hardware Drivers; the only driver listed is my graphics card. Setup: I have a Dell 8250. Speakers are plugged into the SB live card. Woofer and 2 speakers using transformer.

  Read the article

• How to have a soft-real-time process in presense of heavily swapping IO-intensive background load?

  - by Vi

  schedtool: PID 32301: PRIO 4, POLICY R: SCHED_RR , NICE -20, AFFINITY 0xf ionice: realtime: prio 4 But the music is stumbling anyway. Background load is low prio (SCHED_IDLEPRIO, idle ionice), but uses a lot of memory (more than is physically available) and does a lot of IO and calculations. Latencytop shows about 1500ms for: Following symlink Writing buffer to disk (sync) Page fault Writing a page to disk both for the bg load and for unrelated processes. Load average is 10 and counting. Why cannot it allocate, for example, 200MHZ of one of the cores and 32M of memory and not less than once per second opportunity for IO for mplayer to make it happy while continuing calculations on the background? Or: why it cannot leave background task and swap loving each other but keeping the rest of the system as if there were no background load? How to have RT processes AND heavy bg load simultaneously (without of virtual machines)?

  Read the article

• Remote Program (via ssh) suspends when leaving client computer

  - by Philipp F

  I'm working with MATLAB on a remote computer logging in via ssh -X remotepc and running matlab like matlab &. When I start a long-running process and leave the computer, it seems to suspend the process (after like 30mins being away) such that there is nearly no progress over night. As soon as I come back and wake up the client, the remote process continues with the calculation. I can see this from the load-average values (uptime) Why is that and how can I change this behaviour?

  Read the article

• How to run a program and get its PID in the background

  - by Ivan

  I have a Minecraft server startup script that looks like this: #!/bin/bash cd "$(dirname "$0")" exec java -Xmx4096M -Xms4096M -jar minecraft_server.jar How do I get java process's PID while being able to enter input into the Java process? if I change the exec line to exec java -Xmx4096M -Xms4096M -jar minecraft_server.jar & echo $! > pid it won't let me input any text into the Minecraft server java process.

  Read the article

• fstab and cifs mounting, possible to store authentication information outside of fstab?

  - by tj111

  I am currently using cifs to mount some network shares (that require authentication) in /etc/fstab. It works excellently, but I would like to move the authentication details (username/pass) outside of fstab and be able to chmod it 600 (as fstab can have issues if I were to change its permissions). I was wondering if it is possible to do this (many-user system, don't want these permissions to be viewable by all users). from: //server/foo/bar /mnt/bar cifs username=user,password=pass,r 0 0 to: //server/foo/bar /mnt/bar cifs <link to permissions>,r 0 0 (or something analogous to this). Thanks.

  Read the article

• Multiple virtual VLAN interfaces on single NIC (Debian)

  - by RayQuang

  I'm trying to setup multiple virtual interfaces with VLAN's on a single NIC. I'm running Debian Squeeze. Currently this is my /etc/netowrk/interfaces auto eth0.10 iface eth0.10 inet dhcp This gives me a working connection, however I'm not sure how to configure several like these on a single NIC so I can use multiple external IP's. I have tried aliasing the VLAN's like so: iface eth0.10:1 But that was not successful and it said failed to bring up interface. And suggestions would be greatly appreciated :)

  Read the article

• how to setup kismet.conf on Ubuntu

  - by Registered User

  I installed Kismet on my Ubuntu 10.04 machine as apt-get install kismet every thing seems to work fine. but when I launch it I see following error kismet Launching kismet_server: //usr/bin/kismet_server Suid priv-dropping disabled. This may not be secure. No specific sources given to be enabled, all will be enabled. Non-RFMon VAPs will be destroyed on multi-vap interfaces (ie, madwifi-ng) Enabling channel hopping. Enabling channel splitting. NOTICE: Disabling channel hopping, no enabled sources are able to change channel. Source 0 (addme): Opening none source interface none... FATAL: Please configure at least one packet source. Kismet will not function if no packet sources are defined in kismet.conf or on the command line. Please read the README for more information about configuring Kismet. Kismet exiting. Done. I followed this guide http://www.ubuntugeek.com/kismet-an-802-11-wireless-network-detector-sniffer-and-intrusion-detection-system.html#more-1776 how ever in kismet.conf I am not clear with following line source=none,none,addme as to what should I change this to. lspci -vnn shows 0c:00.0 Network controller [0280]: Broadcom Corporation BCM4312 802.11b/g [14e4:4315] (rev 01) Subsystem: Dell Device [1028:000c] Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f69fc000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information <?> Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting <?> Capabilities: [13c] Virtual Channel <?> Capabilities: [160] Device Serial Number Capabilities: [16c] Power Budgeting <?> Kernel driver in use: wl Kernel modules: wl, ssb and iwconfig shows lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"WIKUCD" Mode:Managed Frequency:2.462 GHz Access Point: <00:43:92:21:H5:09> Bit Rate=11 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=1/5 Signal level=-81 dBm Noise level=-90 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:169 Invalid misc:0 Missed beacon:0 So what should I be putting in place of source=none,none,addme with output I mentioned above ?

  Read the article

• end_request: I/O error, dev sda, sector xxxxxxxxx

  - by muruga

  I have a IBM server. This server contains 3 hard disk with RAID 5. It was working fine earlier. Unfortunately this machine got the following error message. After that I have rebooted the systems. After that I am getting the following error message in kern.log and demsg kernel: [65896.678870] end_request: I/O error, dev sda, sector 17430271 kernel: [69263.783957] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK : [69263.783957] sd 0:0:0:0: [sda] Sense Key : Hardware Error [current] kernel: [69263.783957] sd 0:0:0:0: [sda] Add. Sense: Internal target failure Whether it is kernel problem or hard disk problem or Raid problem

  Read the article

• Dual-head monitor system Kubuntu 10.04

  - by andrii

  I have a notebook Asus V6X00V with 1400*1050 monitor(name: LVDS) and Dell Monitor 1920*1080 (VGA-0). I want to have a dual monitor system. At MS Windows everything is working fine. During the Kubuntu installation the Dell and the main notebook monitors have a right resolutions(1920*1080 & 1400*1050). But after some stage it have been changed to the 1152*864 for both. Now the right resolution is only during turning off process and when I am using the console. So it shows that system can use this resolutions. The problem is just in a settings. I am using Size & Orientation - System Settings for setting adjustment. Any option that changes resolution for any monitor or changing position(Absolute, Left Of, Right of and so on) cause the color line noise on the screens. I have tried xrandr: xrandr --output LVDS --mode 1400x1050 --pos 0x0 --output VGA-0 --mode 1920x1080 --right-of LVDS --pos 1400x0 but have received the same result. I have find out that for example the previous version of Randr(1.2, now I have xrandr 1.3) need a xorg.conf file modification to create a big virtual screen, but kubuntu 10.4 don't have xorg.conf and I don't know should I modify xorg for 1.3 version of xrandr or not. Please help me to solve this problem

  Read the article

• How to delete files quicker than rm -rf?

  - by Byakugan

  Is there any way how to delete folder/files quicker than with command rm -rf? It seems my disc is filled with bilions of files (sessions of php5) which were not deleted in cron so I need to delete them manually but it takes hours and it is still not helping reducing the amount. Thank you. My command: rm -rf /var/lib/php5/* Tried also these commands: find /var/lib/php5 -name "sess_*" -exec rm {} \; And perl -e 'chdir "/var/lib/php5/" or die; opendir D, "."; while ($n = readdir D) { unlink $n }'

  Read the article

• Is there a way to make nautilus display the "recently used" files and directories?

  - by Peltier

  Is there a way to make nautilus display the "recently used" files and directories, just like the "open file" dialog does? Just to make my question clearer, here are two screenshots: The GTK open file dialog, showing the recently used items: A nautilus window, which doesn't offer to display recently used items: EDIT : This has been added as a feature request to Nautilus. Don't hesitate to make your voice heard if you want it to happen!

  Read the article

• Lost Root and other user passwords

  - by Webnet

  This isn't a huge deal, because there's very little on the server (literally a file or two) that we actually need off of it. But we disabled root logins as a security measure and can't remember any of our other user passwords. I'm assuming that there's nothing we can do at this point to get into the server? I'm sitting next to the box... Update Oops... actually, I need to export an SVN off of this server. So yeah, there's stuff I need.

  Read the article

• Creating multiple SFTP users for one account

  - by Tom Marthenal

  I'm in the process of migrating an aging shared-hosting system to more modern technologies. Right now, plain old insecure FTP is the only way for customers to access their files. I plan on replacing this with SFTP, but I need a way to create multiple SFTP users that correspond to one UNIX account. A customer has one account on the machine (e.g. customer) with a home directory like /home/customer/. Our clients are used to being able to create an arbitrary number of FTP accounts for their domains (to give out to different people). We need the same capability with SFTP. My first thought is to use SSH keys and just add each new "user" to authorized_keys, but this is confusing for our customers, many of whom are not technically-inclined and would prefer to stick with passwords. SSH is not an issue, only SFTP is available. How can we create multiple SFTP accounts (customer, customer_developer1, customer_developer2, etc.) that all function as equivalents and don't interfere with file permissions (ideally, all files should retain customer as their owner)? My initial thought was some kind of PAM module, but I don't have a clear idea of how to accomplish this within our constraints. We are open to using an alternative SSH daemon if OpenSSH isn't suitable for our situation; again, it needs to support only SFTP and not SSH. Currently our SSH configuration has this appended to it in order to jail the users in their own directories: # all customers have group 'customer' Match group customer ChrootDirectory /home/%u # jail in home directories AllowTcpForwarding no X11Forwarding no ForceCommand internal-sftp # force SFTP PasswordAuthentication yes # for non-customer accounts we use keys instead Our servers are running Ubuntu 12.04 LTS.

  Read the article

• Processes spawned by taskset not respecting environment variables

  - by jonesy16

  I've run into an issue where an intel compiler generated program that I'm running with taskset has been putting its temporary files into the working directory instead of /tmp (defined by environment variable TMPDIR). If run by itself, it works correctly. If run with taskset (e.g. taskset -c 0 <program> Then it seems to completely ignore the TMPDIR environment variable. I then verified this by writing a quick bash script as follows: contents of test.sh: #!/bin/bash echo $TMPDIR When run by itself: $ export TMPDIR=/tmp $ test.sh /tmp When run through taskset: $ export TMPDIR=/tmp $ taskset -c 1 test.sh "" Another test. If I export the TMPDIR variable inside of my script and then use taskset to spawn a new process, it doesn't know about that variable: #!/bin/bash export TMPDIR=/tmp taskset -c 1 sh -c export When run, the list of exported variables does not include TMPDIR. It works correctly with any other exported environment variable. If i diff the output of: export and taskset -c 1 bash -c export Then I see that there are 4 changes. The taskset spawned export doesn't have LD_LIBRARY_PATH, NLSPATH (intel compiler variable), SHLVL is 3 instead of 1, and TMPDIR is missing. Can anyone tell me why?

  Read the article

• external drive and CentOS - Reset high speed USB device number

  - by Phil

  I have 2 external drives (3TB) and both will not work with my centOS Box. Tested them in windows ( different machine ) No problems ( 2.6.32-279.9.1.el6.i686 ) dmesg reports: usb 2-2: new high speed USB device number 3 using ehci_hcd usb 2-2: New USB device found, idVendor=2109, idProduct=0700 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-2: Product: USB 3.0 SATA Bridge usb 2-2: Manufacturer: VIA Labs, Inc. usb 2-2: SerialNumber: 0000000000006121 usb 2-2: configuration #1 chosen from 1 choice scsi6 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access ST3000DM 001-9YN166 CC4B PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg3 type 0 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] 5860533165 512-byte logical blocks: (3.00 TB/2.72 TiB) sd 6:0:0:0: [sdd] Write Protect is off sd 6:0:0:0: [sdd] Mode Sense: 00 06 00 00 sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sdd: sdd1 sd 6:0:0:0: [sdd] Very big device. Trying to use READ CAPACITY(16). sd 6:0:0:0: [sdd] Assuming drive cache: write through sd 6:0:0:0: [sdd] Attached SCSI disk Tyring to use cfdisk / fdisk / gdisk or even fdisk -l results in the program hanging and dmesg reports: usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd usb 2-2: reset high speed USB device number 3 using ehci_hcd I have the same 2 drives physically installed in the computer via SATA Any Ideas?

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >