Search Results

Search found 1653 results on 67 pages for 'defaults'.

Page 49/67 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

• Hardware wireless switch has no effect after suspend and 13.10 upgrade

  - by blaineh

  This seems to be a fairly chronic problem, as shown by the following questions: How do I fix a "Wireless is disabled by hardware switch" error? Wireless disabled by hardware switch "Wireless disabled by hardware switch" after suspend and other hardware buttons ineffective - how can I solve this? but no good solutions have been found! Wireless works fine after a reboot, but after a suspend the hardware switch (for my laptop this is f12) has no effect on the wireless, it is just permanently off, and shows that it is with a red LED. All My rfkill list all reads: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: yes Any combination with rfkill <un>block wifi doesn't work, although one time first blocking then unblocking actually turned it on again. sudo lshw -C network reads: *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 78:e4:00:65:2e:3f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.11.0-12-generic firmware=N/A ip=155.99.215.79 latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:90100000-9010ffff *-network DISABLED description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 02 serial: c8:0a:a9:89:b4:30 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:90010000-90010fff memory:90000000-9000ffff memory:90020000-9002ffff Also, adding a /etc/pm/sleep.d/brcm.sh file as recommended here simply prevents the laptop from suspending at all, which of course is no good. This question has an answer urging to install the original driver, but it wasn't an "accepted answer" so I'd rather not take a chance on it. Also I'll admit I'm a bit lost on that and would like help doing so with the specific information I've given. xev shows that no internal event is triggered for my wireless switch (f12), but other function keys also acting as hardware switches work fine. I would be happy to provide more information, so long as you're willing to help me find it for you! This is a very annoying bug. I have a Compaq Presario CQ62. Edit. I just tried to reload bios defaults (or something) as shown by this video. Didn't work. Edit. I tried the contents of this answer, and it didn't work. Edit. I made a pastebin of dmesg. I couldn't even begin to understand the contents. Edit. Output of lspci | grep Network: 02:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) (rev 01)

  Read the article

• disks not ready in array causes mdadm to force initramfs shell

  - by RaidPinata

  Okay, this is starting to get pretty frustrating. I've read most of the other answers on this site that have anything to do with this issue but I'm still not getting anywhere. I have a RAID 6 array with 10 devices and 1 spare. The OS is on a completely separate device. At boot only three of the 10 devices in the raid are available, the others become available later in the boot process. Currently, unless I go through initramfs I can't get the system to boot - it just hangs with a blank screen. When I do boot through recovery (initramfs), I get a message asking if I want to assemble the degraded array. If I say no and then exit initramfs the system boots fine and my array is mounted exactly where I intend it to. Here are the pertinent files as near as I can tell. Ask me if you want to see anything else. # mdadm.conf # # Please refer to mdadm.conf(5) for information about this file. # # by default (built-in), scan all partitions (/proc/partitions) and all # containers for MD superblocks. alternatively, specify devices to scan, using # wildcards if desired. #DEVICE partitions containers # auto-create devices with Debian standard permissions # CREATE owner=root group=disk mode=0660 auto=yes # automatically tag new arrays as belonging to the local system HOMEHOST <system> # instruct the monitoring daemon where to send mail alerts MAILADDR root # definitions of existing MD arrays # This file was auto-generated on Tue, 13 Nov 2012 13:50:41 -0700 # by mkconf $Id$ ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae Here is fstab # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> # / was on /dev/sdc2 during installation UUID=3fa1e73f-3d83-4afe-9415-6285d432c133 / ext4 errors=remount-ro 0 1 # swap was on /dev/sdc3 during installation UUID=c4988662-67f3-4069-a16e-db740e054727 none swap sw 0 0 # mount large raid device on /data /dev/md0 /data ext4 defaults,nofail,noatime,nobootwait 0 0 output of cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sda[0] sdd[10](S) sdl[9] sdk[8] sdj[7] sdi[6] sdh[5] sdg[4] sdf[3] sde[2] sdb[1] 23441080320 blocks super 1.2 level 6, 512k chunk, algorithm 2 [10/10] [UUUUUUUUUU] unused devices: <none> Here is the output of mdadm --detail --scan --verbose ARRAY /dev/md0 level=raid6 num-devices=10 metadata=1.2 spares=1 name=Craggenmore:data UUID=37eea980:24df7b7a:f11a1226:afaf53ae devices=/dev/sda,/dev/sdb,/dev/sde,/dev/sdf,/dev/sdg,/dev/sdh,/dev/sdi,/dev/sdj,/dev/sdk,/dev/sdl,/dev/sdd Please let me know if there is anything else you think might be useful in troubleshooting this... I just can't seem to figure out how to change the boot process so that mdadm waits until the drives are ready to build the array. Everything works just fine if the drives are given enough time to come online. edit: changed title to properly reflect situation

  Read the article

• Nokia Lumia 920 Windows Phone 8 Announcement

  - by Tim Murphy

  Today Nokia and Microsoft had an event to officially introduce the Lumia 920.  Below is a rundown of some of the things I found interesting. As a person who likes photography there was a lot to drool over.  The main feature that caught my attention was PureView with its optical stabilization.  This alone should improve the majority of you pictures.  Add to that the SmartShoot Object remover that uses multiple images to remove unwanted people or objects that move through your picture and you never have to accept reality again. For the most part the lenses concept introduced in Windows Phone 8 just makes the usability of leveraging camera better.  Of course that is Microsoft’s selling point.  One lens that caught my attention was the Bing lens.  I have to say it is about time that we can take pictures and use them to search for answers using Bing. There were a couple of features shown that involved augmented reality.  One was similar to the yapf application that is already in the market which overlays restaurants and other destination over live camera views.  The other was using the navigation directions with a live view. Then you get down to some of the physical features of the Lumia 920.  The one that got the most stage time is that it has a great 2000mah battery which can be charged wirelessly.  They also pointed out the improved glare reduction of the 4.5 in. curved glass screen.  This hardware improvement is improved further with software that detects glare conditions and adjusts the display attributes to enhance viewing ease. Adding to the wireless cool factor of the Lumia 920 is the general NFC capabilities.  This was demonstrated with NFC docking stations as well as JBL speakers and headphones. There was one more hardware feature that I applauded.  The super sensitive touch screen did away with one of my pet peeves with capacitive touch screens.  You will never have to remove you gloves to operate your phone again.  The mittens that they did the demo with looked more like boxing gloves. I was disappointed with Joe Belfiore said that they were only going to show a couple of new features of the Windows Phone 8 and would hear more at future events.  One of the things he did show is the ability to customize which buttons you preferred as defaults in IE10.  For example you could have the folders button where the refresh button normally is.  He also showed that at long last you can natively take screenshots on your phone.  Hopefully he will be back quickly to give us the rest of the features. The most disappointing part of the event was that we never found out when they would be released or how much they would cost.  Let’s hope this comes soon.  Even with these couple of items still left on my wish list I can’t wait to get my hands on a Lumia 920.  del.icio.us Tags: Windows Phone,Windows Phone 8,Nokia,Lumia,Lumia 920,Microsoft

  Read the article

• How to make Ubuntu recognize an unknown external display (so I can adjust its resolution)?

  - by WagnerAA

  I have a Dell laptop with an external monitor attached (a Samsumg SyncMaster 931c). My laptop display was recognized, and I can adjust its optimum resolution. My external display is still unknown, thus I'm stuck at a lower resolution (1024x768): I tried the "Detect Displays" button, but it didn't work, nothing happens. I recently upgraded from Ubuntu 12.04 to 12.10. Things were working before. I don't know if I can actually change this configuration, or if this is a bug. I searched for an answer here and also in Launchpad's website, but found none. I even tried to install Nvidia drivers, and just messed things up. It seems I wasn't even using nvidia before, as I guessed by looking at my additional drivers configuration: My laptop has an Intel chipset, I guess: $ dpkg --get-selections | grep -i -e nvidia -e intel intel-gpu-tools install libdrm-intel1:amd64 install libdrm-intel1:i386 install nvidia-common install xserver-xorg-video-intel install I don't have an xorg.conf file (I think this is nvidia related, am I right?): $ cat /etc/X11/xorg.conf cat: /etc/X11/xorg.conf: No such file or directory $ ls -l /etc/X11/ total 76 drwxr-xr-x 2 root root 4096 Out 19 23:41 app-defaults drwxr-xr-x 2 root root 4096 Abr 25 2012 cursors -rw-r--r-- 1 root root 18 Abr 25 2012 default-display-manager drwxr-xr-x 4 root root 4096 Abr 25 2012 fonts -rw-r--r-- 1 root root 17394 Dez 3 2009 rgb.txt lrwxrwxrwx 1 root root 13 Mai 1 03:33 X -> /usr/bin/Xorg drwxr-xr-x 3 root root 4096 Out 19 23:41 xinit drwxr-xr-x 2 root root 4096 Jan 23 2012 xkb -rw-r--r-- 1 root root 0 Out 24 08:55 xorg.conf.nvidia-xconfig-original -rwxr-xr-x 1 root root 709 Abr 1 2010 Xreset drwxr-xr-x 2 root root 4096 Out 19 10:08 Xreset.d drwxr-xr-x 2 root root 4096 Out 19 10:08 Xresources -rwxr-xr-x 1 root root 3730 Jan 20 2012 Xsession drwxr-xr-x 2 root root 4096 Out 20 00:11 Xsession.d -rw-r--r-- 1 root root 265 Jul 1 2008 Xsession.options -rw-r--r-- 1 root root 13 Ago 15 06:43 XvMCConfig -rw-r--r-- 1 root root 601 Abr 25 2012 Xwrapper.config Here is some information I gathered by looking at other related posts: $ sudo lshw -C display; lsb_release -a; uname -a *-display:0 description: VGA compatible controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 07 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:48 memory:f6800000-f6bfffff memory:d0000000-dfffffff ioport:1800(size=8) *-display:1 UNCLAIMED description: Display controller product: Mobile 4 Series Chipset Integrated Graphics Controller vendor: Intel Corporation physical id: 2.1 bus info: pci@0000:00:02.1 version: 07 width: 64 bits clock: 33MHz capabilities: pm bus_master cap_list configuration: latency=0 resources: memory:f6100000-f61fffff LSB Version: core-2.0-amd64:core-2.0-noarch:core-3.0-amd64:core-3.0-noarch:core-3.1-amd64:core-3.1-noarch:core-3.2-amd64:core-3.2-noarch:core-4.0-amd64:core-4.0-noarch:cxx-3.0-amd64:cxx-3.0-noarch:cxx-3.1-amd64:cxx-3.1-noarch:cxx-3.2-amd64:cxx-3.2-noarch:cxx-4.0-amd64:cxx-4.0-noarch:desktop-3.1-amd64:desktop-3.1-noarch:desktop-3.2-amd64:desktop-3.2-noarch:desktop-4.0-amd64:desktop-4.0-noarch:graphics-2.0-amd64:graphics-2.0-noarch:graphics-3.0-amd64:graphics-3.0-noarch:graphics-3.1-amd64:graphics-3.1-noarch:graphics-3.2-amd64:graphics-3.2-noarch:graphics-4.0-amd64:graphics-4.0-noarch:printing-3.2-amd64:printing-3.2-noarch:printing-4.0-amd64:printing-4.0-noarch:qt4-3.1-amd64:qt4-3.1-noarch Distributor ID: Ubuntu Description: Ubuntu 12.10 Release: 12.10 Codename: quantal Linux Batcave 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux $ xrandr -q Screen 0: minimum 320 x 200, current 2304 x 800, maximum 32767 x 32767 LVDS1 connected 1280x800+0+0 (normal left inverted right x axis y axis) 286mm x 1790mm 1280x800 59.9*+ 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 connected 1024x768+1280+32 (normal left inverted right x axis y axis) 0mm x 0mm 1024x768 60.0* 800x600 60.3 56.2 848x480 60.0 640x480 59.9 DP1 disconnected (normal left inverted right x axis y axis) If there's anything else I can do, any other information I can post here, to help me configure this external display, please let me know. If this is actually a bug, I apologize (I know bugs are not allowed here), but I really wasn't sure. And I will promptly file a bug report in Launchpad if that's the case. Thanks a lot in advance. ;)

  Read the article

• Hijax == sneaky Javascript redirects? Will I get banned from Google?

  - by Chris Jacob

  Question Will I get penalised as "sneaky Javascript redirects" by Google if I have the following Hijax setup (which requires a JavaScript redirect on the page indexed by google). Goal I want to implement Hijax to enable AJAX content to be accessibile to non-JavaScript users and search engine crawlers. Background I'm working on a static file server (GitHub Pages). No server side tricks allowed (so Google's #! "hash bang" solution is not an option). I'm trying to keep my files DRY. I don't want to repeat the common OUTER template in all my files i.e. header, navigation menu, footer, etc They will live in the main index.html Setup the Hijax index.html page contains all OUTER html/css/js... the site's template. index.html has a <div id="content"> which defaults to containing the "homepage" html. index.html has a navigation menu, with a Hijax link to an "about" page. With JavaScript disabled (e.g. crawler) it follows link to /about.html. With JavaScript enabled (e.g. most people) the link updates the url hash fragment to /#about and jQuery replaces the <div id="content"> innerHTML with $("#content").load("about.html #inner-container");. AJAX content about.html does not contain anything extra to try an cloak content for crawlers. about.html file contains enough HTML / CSS / JavaScript to display /about.html as a standalone page with it's own META data... e.g. <html><head><title>About</title>...</head><body></body></html>. about.html has NO OUTER HTML template (i.e. header, navigation menu, footer, etc). about.html <body> contains a <div id="inner-container"> which holds the content that is injected into index.html. about.html has a <noscript> tag as the first child of <body> which explains to non-JavaScript users that they are viewing the about page "inner content" - with a link to navigate to the index.html page to get the full page layout with menu. The (Sneaky?) Redirect Google indexes the /about.html page. However when a person with JavaScript enabled visits that page there is no OUTER html template (e.g. header, navigation menu, footer, etc). So I need to do a JavaScript redirect to get the person over the /#about page (deeplinking to the "about" page "state" in index.html). I'm thinking of doing a "redirect on click or after 10 seconds". The end results is that user ends up on an "enhanced" page back on index.html with all it's OUTER template - but the core "page" content is practically identical. Known issue with inbound links e.g. Share / Bookmarking It seems that if a user shares the URL /#about on their blog, when allocating inbound links to my site Google ignores everything after the # ... it allocates value to the / page - See: http://stackoverflow.com/questions/5028405/hashbang-vs-hijax/5166665#5166665. I can only try an minimise this issue offering "share" buttons on the page with the appropriate urls i.e. /about.html. Duplicate Sorry. I posted this same question over on http://stackoverflow.com/questions/5561686/hijax-sneaky-javascript-redirects-will-i-get-banned-from-google ... then realised it probably belongs more on this Stack Exchange site... Not sure if I should delete the Stack Overflow question? Or just leave it on both sites? Please leave comment.

  Read the article

• ODEE Green Field (Windows) Part 3 - SOA Suite

  - by AndyL-Oracle

   So you're still here, are you? I'm sure you're probably overjoyed at the prospect of continuing with our green field installation of ODEE. In my previous post, I covered the installation of WebLogic - you probably noticed, like I did, that it's a pretty quick install. I'm pretty certain this had everything to do with how quickly the next post made it to the internet! So let's dig in. Make sure you've followed the steps from the initial post to obtain the necessary software and prerequisites! Unpack the RCU (Repository Creation Utility). This ZIP file contains a directory (rcuHome) that should be extracted into your ORACLE_HOME. Run the RCU – execute rcuHome/bin/rcu.bat. Click Next. Select Create and click Next. Enter the database connection details and click Next – any failure to connection will show in the Messages box. Click Ok Expand and select the SOA Infrastructure item. This will automatically select additional required components. You can change the prefix used, but DEV is recommended. If you are creating a sandbox that includes additional components like WebCenter Content and UMS, you may select those schemas as well but they are not required for a basic ODEE installation. Click Next. Click OK. Specify the password for the schema(s). Then click Next. Click Next. Click OK. Click OK. Click Create. Click Close. Unpack the SOA Suite installation files into a single directory e.g. SOA. Run the installer – navigate and execute SOA/Disk1/setup.exe. If you receive a JDK error, switch to a command line to start the installer. To start the installer via command line, do Start?Run?cmd and cd into the SOA\Disk1 directory. Run setup.exe –jreLoc < pathtoJRE >. Ensure you do not use a path with spaces – use the ~1 notation as necessary (your directory must not exceed 8 characters so “Program Files” becomes “Progra~1” and “Program Files (x86)” becomes “Progra~2” in this notation). Click Next. Select Skip and click Next. Resolve any issues shown and click Next. Verify your oracle home locations. Defaults are recommended. Click Next. Select your application server. If you’ve already installed WebLogic, this should be automatically selected for you. Click Next. Click Install. Allow the installation to progress… Click Next. Click Finish. You can save the installation details if you want. That should keep you satisfied for the moment. Get ready, because the next posts are going to be meaty! 

  Read the article

• Bumblebee [ERROR]Cannot access secondary GPU - error: [XORG]

  - by Lunchbox

  Though this may seem like a duplicate question, none of the suggestions I've seen have worked for me, however nearly all posters get good results. I'll start with hardware: Metabox W350ST notebook Intel Core i7 4700 16GB RAM GTX 765M (with Optimus) 128GB SSD 1TB SSHD My initial error output when trying to optirun a game is: [ERROR]Cannot access secondary GPU - error: [XORG] (EE) NVIDIA(0): Failed to initialize the NVIDIA GPU at PCI:1:0:0. Please [133.973920] [ERROR]Aborting because fallback start is disabled. If anything else is needed to troubleshoot this just let me know. Adding bumblebee.conf: # Configuration file for Bumblebee. Values should **not** be put between quotes ## Server options. Any change made in this section will need a server restart # to take effect. [bumblebeed] # The secondary Xorg server DISPLAY number VirtualDisplay=:8 # Should the unused Xorg server be kept running? Set this to true if waiting # for X to be ready is too long and don't need power management at all. KeepUnusedXServer=false # The name of the Bumbleblee server group name (GID name) ServerGroup=bumblebee # Card power state at exit. Set to false if the card shoud be ON when Bumblebee # server exits. TurnCardOffAtExit=false # The default behavior of '-f' option on optirun. If set to "true", '-f' will # be ignored. NoEcoModeOverride=false # The Driver used by Bumblebee server. If this value is not set (or empty), # auto-detection is performed. The available drivers are nvidia and nouveau # (See also the driver-specific sections below) Driver=nvidia # Directory with a dummy config file to pass as a -configdir to secondary X XorgConfDir=/etc/bumblebee/xorg.conf.d ## Client options. Will take effect on the next optirun executed. [optirun] # Acceleration/ rendering bridge, possible values are auto, virtualgl and # primus. Bridge=auto # The method used for VirtualGL to transport frames between X servers. # Possible values are proxy, jpeg, rgb, xv and yuv. VGLTransport=proxy # List of paths which are searched for the primus libGL.so.1 when using # the primus bridge PrimusLibraryPath=/usr/lib/x86_64-linux-gnu/primus:/usr/lib/i386-linux-gnu/primus # Should the program run under optirun even if Bumblebee server or nvidia card # is not available? AllowFallbackToIGC=false # Driver-specific settings are grouped under [driver-NAME]. The sections are # parsed if the Driver setting in [bumblebeed] is set to NAME (or if auto- # detection resolves to NAME). # PMMethod: method to use for saving power by disabling the nvidia card, valid # values are: auto - automatically detect which PM method to use # bbswitch - new in BB 3, recommended if available # switcheroo - vga_switcheroo method, use at your own risk # none - disable PM completely # https://github.com/Bumblebee-Project/Bumblebee/wiki/Comparison-of-PM-methods ## Section with nvidia driver specific options, only parsed if Driver=nvidia [driver-nvidia] # Module name to load, defaults to Driver if empty or unset KernelDriver=nvidia PMMethod=auto # colon-separated path to the nvidia libraries LibraryPath=/usr/lib/nvidia-current:/usr/lib32/nvidia-current # comma-separated path of the directory containing nvidia_drv.so and the # default Xorg modules path XorgModulePath=/usr/lib/nvidia-current/xorg,/usr/lib/xorg/modules XorgConfFile=/etc/bumblebee/xorg.conf.nvidia ## Section with nouveau driver specific options, only parsed if Driver=nouveau [driver-nouveau] KernelDriver=nouveau PMMethod=auto XorgConfFile=/etc/bumblebee/xorg.conf.nouveau DRIVER VERSION - Output of jockey-text -l: nvidia_304_updates - nvidia_304_updates (Proprietary, Enabled, Not in use)

  Read the article

• Missing Fields and Default Values

  - by PointsToShare

  © 2011 By: Dov Trietsch. All rights reserved Dealing with Missing Fields and Default Values New fields and new default values are not propagated throughout the list. They only apply to new and updated items and not to items already entered. They are only prospective. We need to be able to deal with this issue. Here is a scenario. The user has an old list with old items and adds a new field. The field is not created for any of the old items. Trying to get its value raises an Argument Exception. Here is another: a default value is added to a field. All the old items, where the field was not assigned a value, do not get the new default value. The two can also happen in tandem – a new field is added with a default. The older items have neither. Even better, if the user changes the default value, the old items still carry the old defaults. Let’s go a bit further. You have already written code for the list, be it an event receiver, a feature receiver, a console app or a command extension, in which you span all the fields and run on selected items – some new (no problem) and some old (problems aplenty). Had you written defensive code, you would be able to handle the situation, including similar changes in the future. So, without further ado, here’s how. Instead of just getting the value of a field in an item – item[field].ToString() – use the function below. I use ItemValue(item, fieldname, “mud in your eye”) and if “mud in your eye” is what I get, I know that the item did not have the field.   /// <summary> /// Return the column value or a default value /// </summary> private static string ItemValue(SPItem item, string column, string defaultValue) {     try     {         return item[column].ToString();     }     catch (NullReferenceException ex)     {         return defaultValue;     }     catch (ArgumentException ex)     {         return defaultValue;     } } I also use a similar function to return the default and a funny default-default to ascertain that the default does not exist. Here it is:  /// <summary> /// return a fields default or the "default" default. /// </summary> public static string GetFieldDefault(SPField fld, string defValue) {     try     {         // -- Check if default exists.         return fld.DefaultValue.ToString();     }     catch (NullReferenceException ex)     {         return defValue;     }     catch (ArgumentException ex)     {         return defValue;     } } How is this defensive? You have trapped an expected error and dealt with it. Therefore the program did not stop cold in its track and the required code ran to its end. Now, take a further step - write to a log (See Logging – a log blog). Read your own log every now and then, and act accordingly. That’s all Folks!

  Read the article

• jQuery - discrepency between classname and selectors

  - by Ciel

  I have the following code that I wrote, which I personally found to be pretty nice. It takes a <ul> and it drops down the contents when clicked. But I am having a disconnect here in comprehension, and one I had to do what I feel is a 'dirty hack' to solve. The problem is that I do not want the class `'sidebar-dropdown-open' to be so 'hardwired' in the plugin. However I discovered that there is a very stark difference between... $('.sidebar-dropdown-open') and 'sidebar-dropdown-open and even '.sidebar-dropdown-open. I 'solved' this problem by including two different 'parameters' in my plugin, but I was wondering if someone might give me some insight as to how I could perform this better, and why this was behaving this way. wiring (document load) $(document).ready(function () { $('[data-role="sidebar-dropdown"]').drawer({ open: 'sidebar-dropdown-open', css: '.sidebar-dropdown-open' }); }); html <ul> <li class=" dropdown" data-role="sidebar-dropdown"> <a href="pages/.." class="remote">Link Text</a> <ul class="sub-menu light sidebar-dropdown-menu"> <li><a class="remote" href="pages/...">Link Text</a></li> <li><a class="remote" href="pages/...">Link Text</a></li> <li><a class="remote" href="pages/...">Link Text</a></li> </ul> </li> </ul> javascript (function ($) { $.fn.drawer = function (options) { // Create some defaults, extending them with any options that were provided var settings = $.extend({ open: 'open', css: '.open' }, options); return this.each(function () { $(this).on('click', function (e) { // slide up all open dropdown menus $(settings.css).not($(this)).each(function () { $(this).removeClass(settings.open); // retrieve the appropriate menu item var $menu = $(this).children(".dropdown-menu, .sidebar-dropdown-menu"); // slide down the one clicked on. $menu.slideUp('fast'); $menu.removeClass('active'); }); // mark this menu as open $(this).addClass(settings.open); // retrieve the appropriate menu item var $menu = $(this).children(".dropdown-menu, .sidebar-dropdown-menu"); // slide down the one clicked on. $menu.slideDown(100); $menu.addClass('active'); e.preventDefault(); e.stopPropagation(); }).on("mouseleave", function () { $(this).children(".dropdown-menu").hide().delay(300); }); }) }; })(jQuery); I have tried using settings.open and demanding that it just be a className (.open), etc. - but that does not seem to work. It seems to get ignored by the removeClass function.

  Read the article

• Not enough free disk space

  - by carmatt95

  I'm new to Ubuntu and I'm getting an error in software updater. When I try and do my daily updates, it says: The upgrade needs a total of 25.3 M free space on disk /boot. Please free at least an additional 25.3 M of disk space on /boot. Empty your trash and remove temporary packages of former installations using sudo apt-get clean. I tried typing in sudo apt-get clean into the terminal but I still get the message. All of the pages I read seem to be for experianced Ubuntuers. Any help would be appreciated. I'm running Ubuntu 12.10. I want to upgrade to 13.04 but understand I have to finish these first. EDIT: @Alaa, This is the output from typing in cat /etc/fstab into the terminal: # /etc/fstab: static file system information. # # Use 'blkid' to print the universally unique identifier for a # device; this may be used with UUID= as a more robust way to name devices # that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> /dev/mapper/ubuntu-root / ext4 errors=remount-ro 0 1 # /boot was on /dev/sda1 during installation UUID=fa55c082-112d-4b10-bcf3-e7ffec6cebbc /boot ext2 defaults 0 2 /dev/mapper/ubuntu-swap_1 none swap sw 0 0 /dev/fd0 /media/floppy0 auto rw,user,noauto,exec,utf8 0 0 matty@matty-G41M-ES2L:~$ df -h: Filesystem Size Used Avail Use% Mounted on /dev/mapper/ubuntu-root 915G 27G 842G 4% / udev 984M 4.0K 984M 1% /dev tmpfs 397M 1.1M 396M 1% /run none 5.0M 0 5.0M 0% /run/lock none 992M 1.8M 990M 1% /run/shm none 100M 52K 100M 1% /run/user /dev/sda1 228M 222M 0 100% /boot matty@matty-G41M-ES2L:~$ dpkg -l | grep linux-image: ii linux-image-3.5.0-17-generic 3.5.0-17.28 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-18-generic 3.5.0-18.29 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-19-generic 3.5.0-19.30 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-21-generic 3.5.0-21.32 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-22-generic 3.5.0-22.34 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-23-generic 3.5.0-23.35 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-24-generic 3.5.0-24.37 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-25-generic 3.5.0-25.39 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP ii linux-image-3.5.0-26-generic 3.5.0-26.42 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP iF linux-image-3.5.0-28-generic 3.5.0-28.48 i386 Linux kernel image for version 3.5.0 on 32 bit x86 SMP

  Read the article

• How to layout class definition when inheriting from multiple interfaces

  - by gabr

  Given two interface definitions ... IOmniWorkItem = interface ['{3CE2762F-B7A3-4490-BF22-2109C042EAD1}'] function GetData: TOmniValue; function GetResult: TOmniValue; function GetUniqueID: int64; procedure SetResult(const value: TOmniValue); // procedure Cancel; function DetachException: Exception; function FatalException: Exception; function IsCanceled: boolean; function IsExceptional: boolean; property Data: TOmniValue read GetData; property Result: TOmniValue read GetResult write SetResult; property UniqueID: int64 read GetUniqueID; end; IOmniWorkItemEx = interface ['{3B48D012-CF1C-4B47-A4A0-3072A9067A3E}'] function GetOnWorkItemDone: TOmniWorkItemDoneDelegate; function GetOnWorkItemDone_Asy: TOmniWorkItemDoneDelegate; procedure SetOnWorkItemDone(const Value: TOmniWorkItemDoneDelegate); procedure SetOnWorkItemDone_Asy(const Value: TOmniWorkItemDoneDelegate); // property OnWorkItemDone: TOmniWorkItemDoneDelegate read GetOnWorkItemDone write SetOnWorkItemDone; property OnWorkItemDone_Asy: TOmniWorkItemDoneDelegate read GetOnWorkItemDone_Asy write SetOnWorkItemDone_Asy; end; ... what are your ideas of laying out class declaration that inherits from both of them? My current idea (but I don't know if I'm happy with it): TOmniWorkItem = class(TInterfacedObject, IOmniWorkItem, IOmniWorkItemEx) strict private FData : TOmniValue; FOnWorkItemDone : TOmniWorkItemDoneDelegate; FOnWorkItemDone_Asy: TOmniWorkItemDoneDelegate; FResult : TOmniValue; FUniqueID : int64; strict protected procedure FreeException; protected //IOmniWorkItem function GetData: TOmniValue; function GetResult: TOmniValue; function GetUniqueID: int64; procedure SetResult(const value: TOmniValue); protected //IOmniWorkItemEx function GetOnWorkItemDone: TOmniWorkItemDoneDelegate; function GetOnWorkItemDone_Asy: TOmniWorkItemDoneDelegate; procedure SetOnWorkItemDone(const Value: TOmniWorkItemDoneDelegate); procedure SetOnWorkItemDone_Asy(const Value: TOmniWorkItemDoneDelegate); public constructor Create(const data: TOmniValue; uniqueID: int64); destructor Destroy; override; public //IOmniWorkItem procedure Cancel; function DetachException: Exception; function FatalException: Exception; function IsCanceled: boolean; function IsExceptional: boolean; property Data: TOmniValue read GetData; property Result: TOmniValue read GetResult write SetResult; property UniqueID: int64 read GetUniqueID; public //IOmniWorkItemEx property OnWorkItemDone: TOmniWorkItemDoneDelegate read GetOnWorkItemDone write SetOnWorkItemDone; property OnWorkItemDone_Asy: TOmniWorkItemDoneDelegate read GetOnWorkItemDone_Asy write SetOnWorkItemDone_Asy; end; As noted in answers, composition is a good approach for this example but I'm not sure it applies in all cases. Sometimes I'm using multiple inheritance just to split read and write access to some property into public (typically read-only) and private (typically write-only) part. Does composition still apply here? I'm not really sure as I would have to move the property in question out from the main class and I'm not sure that's the correct way to do it. Example: // public part of the interface interface IOmniWorkItemConfig = interface function OnExecute(const aTask: TOmniBackgroundWorkerDelegate): IOmniWorkItemConfig; function OnRequestDone(const aTask: TOmniWorkItemDoneDelegate): IOmniWorkItemConfig; function OnRequestDone_Asy(const aTask: TOmniWorkItemDoneDelegate): IOmniWorkItemConfig; end; // private part of the interface IOmniWorkItemConfigEx = interface ['{42CEC5CB-404F-4868-AE81-6A13AD7E3C6B}'] function GetOnExecute: TOmniBackgroundWorkerDelegate; function GetOnRequestDone: TOmniWorkItemDoneDelegate; function GetOnRequestDone_Asy: TOmniWorkItemDoneDelegate; end; // implementing class TOmniWorkItemConfig = class(TInterfacedObject, IOmniWorkItemConfig, IOmniWorkItemConfigEx) strict private FOnExecute : TOmniBackgroundWorkerDelegate; FOnRequestDone : TOmniWorkItemDoneDelegate; FOnRequestDone_Asy: TOmniWorkItemDoneDelegate; public constructor Create(defaults: IOmniWorkItemConfig = nil); public //IOmniWorkItemConfig function OnExecute(const aTask: TOmniBackgroundWorkerDelegate): IOmniWorkItemConfig; function OnRequestDone(const aTask: TOmniWorkItemDoneDelegate): IOmniWorkItemConfig; function OnRequestDone_Asy(const aTask: TOmniWorkItemDoneDelegate): IOmniWorkItemConfig; public //IOmniWorkItemConfigEx function GetOnExecute: TOmniBackgroundWorkerDelegate; function GetOnRequestDone: TOmniWorkItemDoneDelegate; function GetOnRequestDone_Asy: TOmniWorkItemDoneDelegate; end;

  Read the article

• MVC Html.ActionLink not passing querystring properly

  - by Dave Hanna

  This seems like it should be pretty straight forward, but I'm apparently confused. I have a List view that displays a paged list. At the bottom I have a set of actionlinks: <%= Html.ActionLink("First Page", "List", new { page = 1} ) %> &nbsp; <%= Html.ActionLink("Prev Page", "List", new { page = Model.PageNumber - 1 }) %> &nbsp; <%= Html.ActionLink("Next Page", "List", new { page = Model.PageNumber + 1 }) %> &nbsp; <%= Html.ActionLink("Last Page", "List", new { page = Model.LastPage } )%> I'm using the basic default routes setup, except with "List" substituted for "Index": routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "List", id = UrlParameter.Optional } // Parameter defaults ); The problem is that the ActionLink helpers are generating links of the form: http://localhost:2083/Retrofit?page=2 rather than http://localhost:2083/Retrofit/?page=2 (with the trailing slash after the controller name & before the query string). When the first URL is routed, it completely loses the query string - if I look at Request.QueryString by the time it gets to the controller, it's null. If I enter the second URL (with the trailing slash), it comes in properly (i.e., QueryString of "page=2"). So how can I either get the ActionLink helper to generate the right URL, or get the Routing to properly parse what ActionLink is generating? Thanks.

  Read the article

• SCons does not clean all files

  - by meowsqueak

  I have a file system containing directories of "builds", each of which contains a file called "build-info.xml". However some of the builds happened before the build script generated "build-info.xml" so in that case I have a somewhat non-trivial SCons SConstruct that is used to generate a skeleton build-info.xml so that it can be used as a dependency for further rules. I.e.: for each directory: if build-info.xml already exists, do nothing. More importantly, do not remove it on a 'scons --clean'. if build-info.xml does not exist, generate a skeleton one instead - build-info.xml has no dependencies on any other files - the skeleton is essentially minimal defaults. during a --clean, remove build-info.xml if it was generated, otherwise leave it be. My SConstruct looks something like this: def generate_actions_BuildInfoXML(source, target, env, for_signature): cmd = "python '%s/bin/create-build-info-xml.py' --version $VERSION --path . --output ${TARGET.file}" % (Dir('#').abspath,) return cmd bld = Builder(generator = generate_actions_BuildInfoXML, chdir = 1) env.Append(BUILDERS = { "BuildInfoXML" : bld }) ... # VERSION = some arbitrary string, not important here # path = filesystem path, set elsewhere build_info_xml = "%s/build-info.xml" % (path,) if not os.path.exists(build_info_xml): env.BuildInfoXML(build_info_xml, None, VERSION = build) My problem is that 'scons --clean' does not remove the generated build-info.xml files. I played around with env.Clean(t, build_info_xml) within the 'if' but I was unable to get this to work - mainly because I could not work out what to assign to 't' - I want a generated build-info.xml to be cleaned unconditionally, rather than based on the cleaning of another target, and I wasn't able to get this to work. If I tried a simple env.Clean(None, "build_info_xml") after but outside the 'if' I found that SCons would clean every single build-info.xml file including those that weren't generated. Not good either. What I'd like to know is how SCons goes about determining which files should be cleaned and which should not. Is there something funny about the way I've used a generator function that prevents SCons from recording this target as a Clean candidate?

  Read the article

• SmartGWT TreeGrid, adding and editing

  - by Banang

  I'm trying to programmatically add a new TreeNode to a TreeGrid, and then turn on editing for the newly added node. This is my data source: DataSource ds = new DataSource(); DataSourceTextField idField = new DataSourceTextField("key", "Id"); DataSourceTextField nameField = new DataSourceTextField("name", "Name"); DataSourceTextField keyField = new DataSourceTextField("id", "Key"); keyField.setPrimaryKey(true); ds.setFields(idField, keyField, nameField); ds.setClientOnly(true); My fields: TreeGridField name = new TreeGridField("name", "Name"); TreeGridField id = new TreeGridField("id", "Id"); TreeGridField key = new TreeGridField("key", "Key"); key.setHidden(true); id.setHidden(true); And my code for adding a new record: TreeNode parent = (TreeNode) treeGrid.getSelectedRecord(); if (parent == null) parent = treeGrid.getData().getRoot(); Tree data = treeGrid.getData(); node = data.add(node, parent); Now, how on earth do I switch on editing for the added node? I've tried startEditing(), but that defaults to the first node, and I don't see any way of obtaining the row number for the newly added node, which would allow me to use startEditing(rowNum, colNum, suppressFocus). Using startEditNew() is not an option for many reasons, mainly because that method adds the new node to the bottom of the tree, which doesn't work at all with my app. How do I do this? Grateful for any help you guys can give me.

  Read the article

• Why can't I resolve ambiguity with Android.OS.Environment?

  - by C. Lang

  I'm trying to use Environment.(...) in my Xamarin app. It complains that "Environment is an ambiguous reference between System.Environment and Android.OS.Environment" I can fix it by using the fully qualified name System.Environment.(...) but not with Android.OS.Environment.(...). For example: // Obviously ambiguous with error above using System; using Android.OS; // ... // OnCreate uses Bundle also in Android.OS //... string path = Environment.GetFolderPath(Environment.SpecialFolder.Personal); // Can be fixed by prefixing Environment with "System." But I can't fix it with any variation of possibilities using Android.OS including removing it and explicitly using it. The auto-complete box only shows the Activities and "Resource" and not any of the classes. // Solution to be able to use Android's Environment using Android.OS; // same as above Java.IO.File storageDir = Environment.ExternalStorageDirectory; // Defaults to Android.OS but can still use "System.Environment.(...) // Of course not with this example, but with the one above; yes. // Why doesn't it work both ways? If I remove the using statement and // try to use Android.OS.Environment.(...) it complains // 'OS type or namespace doesn't not exist' The reason is prefixing with Android. is referring to MyAppName.App.Android. Why is that and is there a way to directly access Android.OS.(...)? I've tried Mono.Android.OS.(...).

  Read the article

• ASP.NET MVC in a subfolder (only) on godaddy

  - by Anthony Potts

  Okay, I have read many of the routing posts concerning putting asp.net mvc on godaddy. However, I have not come to a solution to my current problem. I am trying to publish an ASP.NET MVC application to a subfolder on godaddy. I have upgraded the account to use IIS 7 and I have included the MVC dlls in \bin\ deployment method. However, I suspect that my route is not correct. Currently, my routes are set up with the standard out of the box route: public static void RegisterRoutes(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "Index", id = "" } // Parameter defaults ); } I have a subdomain set up so that it looks like office.domain.com. The subdomain is pointing at a folder "/office/" which is right off the root folder. (There is not an MVC application installed in the root folder). All of my application has been placed in this 'office' folder. When I hover over the links however, the 'office' portion shows up in the link as well. e.g. Hovering over a link to the customer controller, index action yields "office.domain.com/office/Customer" as the target. This link then gets a 404 when I attempt to go to it. What should my route be to fix this? Is there something I have neglected in setting up the subdomain in godaddy? Is this something I just can't do in godaddy's domain management "tool". Do I need to set up a virtual directory for this instead of just a directory? Update: I changed the IIS settings in godaddy to use integrated pipeline mode, per this discussion and I am no longer getting 404 errors. The application worked just fine as suggested it would.

  Read the article

• Using QTDesigner with PyQT and Python 2.6

  - by PyNewbie27

  Hi. I'm fairly new to Python and trying to work with the latest versions of QTDesigner, PyQT 4.7 and QT4.7 (I downloaded the whole package from PyQT4.7 website). I can't figure out how to make QTDesigner integrate closely with Python: ie. If I select "Form" View Code in QTDesigners menu, it errors saying "Unable to launch C:/Python26/Lib/site-packages/PyQT4/bin\uic." If I look in that directory there is a pyuic.py but not "uic". From searching online it seems this doesn't exist because it's expecting a C++ install instead of the python version. Is there anyway to make QTDesigner use/call pyuic.py to generate the code, then open an IDE or text editor of my choice to show me the PYTHON code generated by the QTDesigner-PyUIC chain? I'd like Designer to integrate closely with python, so I can make custom slots/signals in Designer while designing, then tweak the python code directly in my IDE later. If it is not possible to code directly inside QTDesigner using python, does that mean I have to hand code my programs entire UI directly in my PythonIDE? Using Designer directly would seemingly be nearly very very nice for a newbie such as myself, since I can see what properties each widget has and visually edit them while still learning the QT syntax without constantly having to use web resources to see what properties each widget should have and helps with boilerplate code generation, and what their defaults are, etc. I've googled and nobody seems to be using QTDesigner and Python in this manner together. It seems most are either handcoding all the QT code in their Python IDE of choice, or have found an obvious/easy method of doing what I want, therefore not really producing up to date tutorials on making this work together. Please enlighten me if you can. Thanks in advance for your time. Please include any suggestions you might have to a newbie trying to use Python with QT and QTDesigner. Thank you.

  Read the article

• ASP.NET MVC 3: RouteExistingFiles = true seems to have no effect

  - by Oleksandr Kaplun

  I'm trying to understand how RouteExistingFiles works. So I've created a new MVC 3 internet project (MVC 4 behaves the same way) and put a HTMLPage.html file to the Content folder of my project. Now I went to the Global.Asax file and edited the RegisterRoutes function so it looks like this: public static void RegisterRoutes(RouteCollection routes) { routes.RouteExistingFiles = true; //Look for routes before looking if a static file exists routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new {controller = "Home", action = "Index", id = UrlParameter.Optional} // Parameter defaults ); } Now it should give me an error when I'm requesting a localhost:XXXX/Content/HTMLPage.html since there's no "Content" controller and the request definitely hits the default pattern. But instead I'm seeing my HTMLPage. What am I doing wrong here? Update: I think I'll have to give up. Even if I'm adding a route like this one: routes.MapRoute("", "Content/{*anything}", new {controller = "Home", action = "Index"}); it still shows me the content of the HTMLPage. When I request a url like ~/Content/HTMLPage I'm getting the Index page as expected, but when I add a file extenstion like .html or .txt the content is shown (or a 404 error if the file does not exist). If anyone can check this in VS2012 please let me know what result you're getting. Thank you.

  Read the article

• ASP.NET MVC Routing - Redirect to aspx?

  - by bmoeskau

  This seems like it should be easy, but for some reason I'm having no luck. I'm migrating an existing WebForms app to MVC, so I need to keep the root of the site pointing to my existing aspx pages for now and only apply routing to named routes. Here's what I have: public static void RegisterRoutes(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.IgnoreRoute("{resource}.aspx/{*pathInfo}"); RouteTable.Routes.Add( "Root", new Route("", new DefaultRouteHandler()) ); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Calendar2", action = "Index", id = "" } // Parameter defaults ); } So aspx pages should be ignored, and the default root url should be handled by this handler: public class DefaultRouteHandler : IRouteHandler { public IHttpHandler GetHttpHandler(RequestContext requestContext) { return System.Web.Compilation.BuildManager.CreateInstanceFromVirtualPath( "~/Dashboard/default.aspx", typeof(Page)) as IHttpHandler; } } This seems to work OK, but the resulting YPOD gives me this: Multiple controls with the same ID '__Page' were found. Trace requires that controls have unique IDs. which seems to imply that the page is somehow getting rendered twice. If I simply type in the url to my dashboard page directly it works fine (no routing, no error). I have no idea why the handler code would be doing anything differently. Bottom line -- I'd like to simply redirect the root url path to an aspx of my choosing -- can anyone shed some light?

  Read the article

• Asp.net MVC Route class that supports catch-all parameter anywhere in the URL

  - by Robert Koritnik

  the more I think about it the more I believe it's possible to write a custom route that would consume these URL definitions: {var1}/{var2}/{var3} Const/{var1}/{var2} Const1/{var1}/Const2/{var2} {var1}/{var2}/Const as well as having at most one greedy parameter on any position within any of the upper URLs like {*var1}/{var2}/{var3} {var1}/{*var2}/{var3} {var1}/{var2}/{*var3} There is one important constraint. Routes with greedy segment can't have any optional parts. All of them are mandatory. Example This is an exemplary request http://localhost/Show/Topic/SubTopic/SubSubTopic/123/This-is-an-example This is URL route definition {action}/{*topicTree}/{id}/{title} Algorithm Parsing request route inside GetRouteData() should work like this: Split request into segments: Show Topic SubTopic SubSubTopic 123 This-is-an-example Process route URL definition starting from the left and assigning single segment values to parameters (or matching request segment values to static route constant segments). When route segment is defined as greedy, reverse parsing and go to the last segment. Parse route segments one by one backwards (assigning them request values) until you get to the greedy catch-all one again. When you reach the greedy one again, join all remaining request segments (in original order) and assign them to the greedy catch-all route parameter. Questions As far as I can think of this, it could work. But I would like to know: Has anyone already written this so I don't have to (because there are other aspects to parsing as well that I didn't mention (constraints, defaults etc.) Do you see any flaws in this algorithm, because I'm going to have to write it myself if noone has done it so far. I haven't thought about GetVirtuaPath() method at all.

  Read the article

• ASP.NET MVC2 Routing Issue With StructureMap

  - by alphadogg

  So, in global.asax, I have: public static void RegisterRoutes(RouteCollection routes) { routes.IgnoreRoute("{resource}.axd/{*pathInfo}"); routes.IgnoreRoute(" { *favicon }", new { favicon = @"(.*/)?favicon.ico(/.*)?" }); routes.IgnoreRoute("{*robotstxt}", new { robotstxt = @"(.*/)?robots.txt(/.*)?" }); routes.MapRoute( "Default", // Route name "{controller}/{action}/{id}", // URL with parameters new { controller = "Home", action = "Index", id = UrlParameter.Optional } // Parameter defaults ); } protected void Application_Start() { var container = new Container(); ServiceLocator.SetLocatorProvider(() => new StructureMapServiceLocator(container)); ComponentRegistrar.Register(container); Debug.WriteLine(container.WhatDoIHave()); // original MVC2 code at project startup AreaRegistration.RegisterAllAreas(); RegisterRoutes(RouteTable.Routes); } and in my StructureMapControllerFactory, I have: protected override IController GetControllerInstance(RequestContext requestContext, Type controllerType) { if (requestContext == null) { throw new ArgumentNullException("requestContext"); } if (controllerType == null) { //return base.GetControllerInstance(requestContext, controllerType); controllerType = GetControllerType(requestContext, "Home"); requestContext.RouteData.Values["Controller"] = "Home"; requestContext.RouteData.Values["action"] = "Index"; } try { return theContainer.GetInstance(controllerType) as Controller; } catch (StructureMapException) { System.Diagnostics.Debug.WriteLine(theContainer.WhatDoIHave()); throw; } } Now, normally, in most examples you find on the net, when controllerType is null, you have the commented out line (base.GetControllerInstance()) that handles it. However, if I use that, I get an error about not finding the controller for default.aspx when the controllerType is null at startup of the web app. If I force the use of the Home controller, I get the site to appear. What am I doing wrong? Is it a problem in routing?

  Read the article

• Django - The included urlconf doesn't have any patterns in it

  - by unsorted

  My website, which was working before, suddenly started breaking with the error "ImproperlyConfigured at / The included urlconf resume.urls doesn't have any patterns in it" The project base is called resume. In settings.py I have set ROOT_URLCONF = 'resume.urls' Here's my resume.urls, which sits in the project root directory. from django.conf.urls.defaults import * # Uncomment the next two lines to enable the admin: from django.contrib import admin admin.autodiscover() urlpatterns = patterns('', # Example: # (r'^resume/', include('resume.foo.urls')), # Uncomment the admin/doc line below and add 'django.contrib.admindocs' # to INSTALLED_APPS to enable admin documentation: (r'^admin/doc/', include('django.contrib.admindocs.urls')), # Uncomment the next line to enable the admin: (r'^admin/', include(admin.site.urls)), (r'^accounts/login/$', 'django.contrib.auth.views.login'), #(r'^employer/', include(students.urls)), (r'^ajax/', include('urls.ajax')), (r'^student/', include('students.urls')), (r'^club/(?P<object_id>\d+)/$', 'resume.students.views.club_detail'), (r'^company/(?P<object_id>\d+)/$', 'resume.students.views.company_detail'), (r'^program/(?P<object_id>\d+)/$', 'resume.students.views.program_detail'), (r'^course/(?P<object_id>\d+)/$', 'resume.students.views.course_detail'), (r'^career/(?P<object_id>\d+)/$', 'resume.students.views.career_detail'), (r'^site_media/(?P<path>.*)$', 'django.views.static.serve', {'document_root': 'C:/code/django/resume/media'}), ) Anyone know what's wrong? This is driving me crazy. Thanks,

  Read the article

• MVC controller is being called twice

  - by rboarman

  Hello, I have a controller that is being called twice from an ActionLink call. My home page has a link, that when clicked calls the Index method on the Play controller. An id of 100 is passed into the method. I think this is what is causing the issue. More on this below. Here are some code snippets: Home page: <%= Html.ActionLink(“Click Me”, "Index", "Play", new { id = 100 }, null) %> Play Controller: public ActionResult Index(int? id) { var settings = new Dictionary<string, string>(); settings.Add("Id", id.ToString()); ViewData["InitParams"] = settings.ToInitParams(); return View(); } Play view: <%@ Page Title="" Language="C#" Inherits="System.Web.Mvc.ViewPage" %> (html <head> omitted for brevity) <body> <form id="form1" runat="server" style="height:100%"> Hello </form> </body> If I get rid of the parameter to the Index method, everything is fine. If I leave the parameter in place, then the Index method is called with 100 as the id. After returning the View, the method is called a second time with a parameter of null. I can’t seem to figure out what is triggering the second call. My first thought was to add a specific route like this: routes.MapRoute( "Play", // Route name "Play/{id}", // URL with parameters new {controller = "Play", action = "Index"} // Parameter defaults ); This had no effect other than making a prettier looking link. I am not sure where to go from here. Thank you in advance. Rick

  Read the article

• Extjs Dynamic Grid

  - by rkenshin

  Hi, I'm trying to create a dynamic grid using Extjs. The grid is built and displayed when a click event is fired then an ajax request is sent to the server to fetch the columns, records and records definition a.k.a Store Fields. Each node could have different grid structure and that depends on the level of the node in the tree. The only way i came up with so far is function showGrid(response, request) { var jsonData = Ext.util.JSON.decode(response.responseText); var grid = Ext.getCmp('contentGrid'+request.params.owner); if(grid) { grid.destroy(); } var store = new Ext.data.ArrayStore({ id : 'arrayStore', fields : jsonData.recordFields, autoDestroy : true }); grid = new Ext.grid.GridPanel({ defaults: {sortable:true}, id:'contentGrid'+request.params.owner, store: store, columns: jsonData.columns, //width:540, //height:200, loadMask: true }); store.loadData(jsonData.records); if(Ext.getCmp('tab-'+request.params.owner)) { Ext.getCmp('tab-'+request.params.owner).show(); } else { grid.render('grid-div'); Ext.getCmp('card-tabs-panel').add({ id:'tab-'+request.params.owner, title: request.params.text, iconCls:'silk-tab', html:Ext.getDom('grid-div').innerHTML, closable:true }).show(); } } The function above is called when a click event is fired 'click': function(node) { Ext.Ajax.request({ url: 'showCtn', success: function(response, request) { alert('Success'); showGrid(response,request); }, failure: function(results, request) { alert('Error'); }, params: Ext.urlDecode(node.attributes.options); } The problem i'm getting with this code is that a new grid is displayed each time the showGrid function is called. The end user sees the old grids and the new one. To mitigate this problem, I tried destroying the grid and also removing the grid element on each request, and that seems to solve the problem only that records never get displayed this time. if(grid) { grid.destroy(true); } The behavior i'm looking for is to display the result of a grid within a tab and if that tab exists replaced the old grid. Any help is appreciated. Thank you

  Read the article

• Does Django cache url regex patterns somehow?

  - by Emre Sevinç

  I'm a Django newbie who needs help: Even though I change some urls in my urls.py I keep on getting the same error message from Django. Here is the relevant line from my settings.py: ROOT_URLCONF = 'mydjango.urls' Here is my urls.py: from django.conf.urls.defaults import * # Uncomment the next two lines to enable the admin: from django.contrib import admin admin.autodiscover() urlpatterns = patterns('', # Example: # (r'^mydjango/', include('mydjango.foo.urls')), # Uncomment the admin/doc line below and add 'django.contrib.admindocs' # to INSTALLED_APPS to enable admin documentation: #(r'^admin/doc/', include(django.contrib.admindocs.urls)), # (r'^polls/', include('mydjango.polls.urls')), (r'^$', 'mydjango.polls.views.homepage'), (r'^polls/$', 'mydjango.polls.views.index'), (r'^polls/(?P<poll_id>\d+)/$', 'mydjango.polls.views.detail'), (r'^polls/(?P<poll_id>\d+)/results/$', 'mydjango.polls.views.results'), (r'^polls/(?P<poll_id>\d+)/vote/$', 'mydjango.polls.views.vote'), (r'^polls/randomTest1/', 'mydjango.polls.views.randomTest1'), (r'^admin/', include(admin.site.urls)), ) So I expect that whenever I visit http://mydjango.yafz.org/polls/randomTest1/ the mydjango.polls.views.randomTest1 function should run because in my polls/views.py I have the relevant function: def randomTest1(request): # mainText = request.POST['mainText'] return HttpResponse("Default random test") However I keep on getting the following error message: Page not found (404) Request Method: GET Request URL: http://mydjango.yafz.org/polls/randomTest1 Using the URLconf defined in mydjango.urls, Django tried these URL patterns, in this order: 1. ^$ 2. ^polls/$ 3. ^polls/(?P<poll_id>\d+)/$ 4. ^polls/(?P<poll_id>\d+)/results/$ 5. ^polls/(?P<poll_id>\d+)/vote/$ 6. ^admin/ 7. ^polls/randomTest/$ The current URL, polls/randomTest1, didn't match any of these. I'm surprised because again and again I check urls.py and there is no ^polls/randomTest/$ in it, but there is ^polls/randomTest1/' It seems like Django is somehow storing the previous contents of urls.py and I just don't know how to make my latest changes effective. Any ideas? Why do I keep on seeing some old version of regexes when I try to load that page even though I changed my urls.py?

  Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >