Search Results

Search found 14951 results on 599 pages for 'connect by'.

Page 496/599 | < Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >

• How to set TV-out options under Linux of an Geforce 9600 GT video card

  - by polemon

  I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• Sync desktop Mac environment to laptop

  - by Andrew Vit

  I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

  Read the article

• libvirt's dnsmasq does not respond to dns queries or provide dhcp

  - by Jeremy

  This is on Ubuntu 10.04 server, using KVM to run Ubuntu guests. This system has been working for a long time and I have not changed anything (other than applying security updates), but today I found dnsmasq no longer responds to requests. I cannot say how long this has been broken for me because I don't frequently use the NAT'd guests. So it could have started just after the last updates or some other event and I just now found it. I can connect to port 53 with telnet at 192.168.122.1. I've flushed ip-tables to be sure it wasn't firewall rules and that is not the problem. dnsmasq is running, virsh reports default network as stared. I can't find ANY information on troubleshooting libvirt dnsmasq except that it won't play well with other instances of dnsmasq, which is not the problem. I cannot even find where log entries might be for this service. Any ideas on where to look for more information? edit to add: I added another network and that one works fine. I guess I have a workaround but would still like to figure out how to troubleshoot this problem.

  Read the article

• openvpn problem

  - by Jared Voronik

  I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

• Orphaned SQL Recordsets/Connections with IIS

  - by Damian

  I have an IIS 6 site running on Windows 2003 Server x86 with MS SQL2005 Enterprise edition running ASP Classic (no choice). The site runs very fast with about 8000 page views per hour. All of my SQL tables are indexed and I have used the profiler to check my queries, the slowest of which is only about 10-15ms. I have autoshrink disabled, autogrow is set to 250mb, database is 2gb with 800mb of free space. My problem is that every now and then the site will slow to a crawl for no reason. Pages that just have a simple 'connect to databse and increment a hit counter' work ok, but more SQL intensive pages that normally execute in about 60ms take 25,000ms to run. This happens for about 30 seconds and then goes away. I was having an issue with orphan recordsets and connections due to the way I was releasing them. I have fixed this up and the issue is much better, but I am still getting them. Is there a way with permon, etc. to track when SQL Server or Windows closes these Orphan connections? At least if I can monitor the issue I will know if I am making progress or if I am even looking at the right things. Is there anything else I might be missing? Thank you!

  Read the article

• Samba Does Not List Files In Shared Directory

  - by Sean M

  I am running Samba on a CentOS server, and I am experiencing a problem where it allows me to connect to the server and see a share, but shows the share as an empty directory. I find this behavior strange. Here is the stanza in my smb.conf for the given share: [seanm] path = /home/seanm writeable = yes valid users = seanm, root read only = No Here's what I see on the server side: [seanm@server ~]$ ls -l -rw-r--r-- 1 seanm seanm 40 Jan 4 13:45 pangram.txt And yet: [seanm@client ~]$ smbclient //server/seanm -U seanm -W WORKGROUP Enter seanm's password: Domain=[WORKGROUP] OS=[Unix] Server=[Samba 3.0.33-3.29.el5_5.1] smb: \> ls . D 0 Fri Jan 7 10:08:55 2011 .. D 0 Fri Jan 7 07:58:31 2011 58994 blocks of size 262144. 50356 blocks available This behavior is present on both a Windows client and a Linux client system. The behavior is present with the firewall on and with the firewall off, so it's not that. Neither /var/log/messages nor /var/log/secure have any complaints about Samba. I doubt that SELinux is a problem: just in case, here are the relevant settings. [root@server ~]# getsebool -a | grep samba samba_domain_controller --> off samba_enable_home_dirs --> on samba_export_all_ro --> off samba_export_all_rw --> off samba_share_fusefs --> off samba_share_nfs --> off use_samba_home_dirs --> on virt_use_samba --> off What am I doing wrong here, and what can I do to fix it?

  Read the article

• Virtualbox port forwarding with iptables

  - by jverdeyen

  I'm using a virtualmachine (virtualbox) as mailserver. The host is an Ubuntu 12.04 and the guest is an Ubuntu 10.04 system. At first I forwarded port 25 to 2550 on the host and added a port forward rule in VirtualBox from 2550 to 25 on the guest. This works for all ports needed for the mailserver. The guest has a host only connection and a NAT (with the port-forwarding). My mailserver was receiving and sending mail properly. But all connections are comming from the virtualbox internal ip, so every host connection is allowed, and that's not what I want. So.. I'm trying to skip the VirtualBox forwarding part and just forward port 25 to my host only ip of the guest system. I used these rules: iptables -F iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -A INPUT --protocol tcp --dport 25 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -s 192.168.99.0/24 -i vboxnet0 -j ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp -i eth0 -d xxx.host.ip.xxx --dport 25 -j DNAT --to 192.168.99.105:25 iptables -A FORWARD -s 192.168.99.0/24 -i vboxnet0 -p tcp --dport 25 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.99.0 -o eth0 -j MASQUERADE iptables -L -n But after these changes I still can't connect with a simple telnet. (Which was possible with my first solution). The guest machine doesn't have any firewall. I only have one network interface on the host (eth0) and a host interface (vboxnet0). Any suggestions? Or should I go back to my old solution (which I don't really like). Edit: bridge mode isn't an option, I have only on IP available for the moment. Thanks!

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• SVN hangs on commit - any suggestions for troubleshooting?

  - by Richard Beier

  We're having a problem with SVN... Subversion clients such as TortoiseSVN hang when we commit any more than a few files at a time to our server. Everything appears to actually be committed successfully to the repository; but the client hangs after all the data has been transmitted. We're using version 1.4.4 of the SVN server. We use the svn:// protocol rather than http to connect. We've reproduced this problem with several clients: TortoiseSVN (1.6.10), AnkhSVN (2.1), and the Silk command-line client (1.6.12). This is happening for everyone on the team, though some people seem to be more affected than others. If someone commits only a few files, it often works; but with more than half a dozen files, it usually hangs. Does anyone have troubleshooting suggestions? This has been happening sporadically for a while, but it's become pretty consistent lately. We've been working around the issue by killing the hung SVN client, doing "svn cleanup", and then doing "svn up"; but sometimes that causes tree conflicts. Another workaround is to blow away the workspace and check it out again after every commit; but of course that's pretty annoying. Are there any diagnostics that could help us troubleshoot this? We're considering upgrading to SVN 1.6 server, and installing the server on a new machine; but we're wondering if there's an easier solution. Thanks for your help, Richard

  Read the article

• Problem with Outlook 2010 (SMTP AUTH LOGIN)

  - by Filipe YaBa Polido

  I have to connect one customer Outlook 2010 to a remote server on which I have either no right, neither way to talk to the sysadmin. This is the thing, after installing and reviewing the logs on Wireshark: Outlook Express: HELO machine AUTH LOGIN username base64 encoded password base64 encoded mails go through. Outlook 2010: HELO machine AUTH DIGEST-MD5 response from server Outlook sends just a * AUTH LOGIN password base64 encoded So... I can send mails in the same domain, but can't send outside, it gives me a relay denied message. My point is... Why the h**l Outlook 2010 doesn't send the username AND the password?! It can never login the right way :| With other versions of Outlook it works fine, and with OE works great, it auths and allows to send mail to a different domain. I've googled and nothing worked. I'm pretty sure that I'm not alone with this one. My last resort will be to configure a local proxy/server that relays to the original one :| Any help would be appreciated. Sorry my bad english as is not my natural language. Thanks.

  Read the article

• Connecting to unsecured wireless network

  - by Sanchez

  I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

  Read the article

• ubuntu 9.04 pptp broken after a power failure

  - by kevin42

  I have a small Ubuntu 9.04 router setup as a NAT box and a PPTP server. After a power failure everything except the PPTP server still works. A windows client gets to "registering your computer on the network" but then says Error 742: The remote computer does not support the required data encryption type. I did some research and I think the problem is with the ppp_mppe module. When I try to run 'modprobe ppp_mppe' it hangs indefinitely. What would cause this hang? Any ideas how I can troubleshoot this further? Thanks for the help! UPDATE: I am still having the problem, however I have found some more information. When the first user tries to connect to pptp, the process list shows modprobe sha1 running, and one instance of modprobe ppp_mppe for each connection attempt. If I killall modprobe at this point the next connection attempt works, and everything is fine until the next reboot. I'm planning to do a clean install at some point in the future but I'd really like to get to the real cause of this.

  Read the article

• HTTP request hangs for for exactly 150 seconds, then gives incomplete response. How do I find out wh

  - by Nathan

  I am hosting a Wordpress blog, and having a strange problem. When I connect to the server (http://71.65.199.125/ at the time of this writing) it displays the Title correctly, and half of a download bar, indicating it has received some of the page, then it hangs for exactly 150 seconds (timed it twice), then it sends the rest of the page, but without the stylesheet. after that it hangs indefinitely, continuing to say "connecting..." without making any progress. If you have any clues as to what might be happening, or how I could print debug logs of PHP or something to see what it is looking for during that hang time that would probably help. recent changed I have made: switched wordpress themes, however I did see it work once with the new theme. moved the server to another building, with an identical ISP, and linksys router forwarding setup. I have also added a favicon.gif file to /var/www but without linking to it from any of the wordpress pages. I have also had a unanticipated power interruption. System info: Ubuntu debian 9.04 Apache2 PHP 5 Wordpress 2.9.2 Thank you

  Read the article

• Sending bulkmail from different server?

  - by Omer Gencay

  I want to send bulk domains from my vps for a domain(cagetur.com) hosted in another company. The company(cagetur) will go on using the old hosting account for its mailing operations. The vps will just be used for smtp for once a week. I created an A record "vps.cagetur.com". directed it to the IP adress of vps then created a mx record with bigger preference number "50 vps.cagetur.com." on the domain control panel. When I trace the "vps.cagetur.com" i can reach my vps now. I installed hMail on the vps. Configure it (created domain, accounts). I have no information about "system" so i couldn't get further from this point. I can connect to the mail server with Outlook without errors. I can send an email from the account on the vps but it doesn't reaches. No errors, no emails. What do i have to do for getting it work? Thank you.

  Read the article

• XenServer VMs can't reach network

  - by toto

  I'm currently trying to setup a small cloud architecture , I'm using in the installation CloudStack 2.2.14 which need two node : a management server (as node1) to provision the cloud and a hyperviser XenServer 5.6 SP2 to host the VMs (as node2). I succeded to create both node1 and node2 into an ESXi 5 VMWare as VMs. So The ESXi 5 is hosting two VMs node1 + node2 , and node2 which is the XenServer will host also VMs (such as ubuntu or Centos). Both node1 and node2 can ping each other and can get the internet connection from Esxi5 ,but My problem is : that VMs into the node2(XenServer) can't reach the network (can't ping node1 or Esxi or get an internet connection but they can ping VMs IN the node2(XenServer). So I tried to: 1-Setup a DHCP server as node3 in ESXi5 and connect node2(Xenserver) to him , but always the VMs into to node2 can't reach the outer network. 2-Setup a DCHP server into node2 , but always the same problem. So , 1-is there any other configuration i'm missing in node2 (considering that I'm sure about DNS , GW , NETMASK configuration)?. 2-Is it the problem because i'm Creating VMs into node2(XenSever) which is a VM into ESXi 5 ?

  Read the article

• Odd log entries when starting up PotgreSQL

  - by Shadow

  When restarting pgSQL, I get the following log entries: 2010-02-10 16:08:05 EST LOG: received smart shutdown request 2010-02-10 16:08:05 EST LOG: autovacuum launcher shutting down 2010-02-10 16:08:05 EST LOG: shutting down 2010-02-10 16:08:05 EST LOG: database system is shut down 2010-02-10 16:08:07 EST LOG: database system was shut down at 2010-02-10 16:08:05 EST 2010-02-10 16:08:07 EST LOG: autovacuum launcher started 2010-02-10 16:08:07 EST LOG: database system is ready to accept connections 2010-02-10 16:08:07 EST LOG: connection received: host=[local] 2010-02-10 16:08:07 EST LOG: incomplete startup packet 2010-02-10 16:08:07 EST LOG: connection received: host=[local] 2010-02-10 16:08:07 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:08 EST LOG: connection received: host=[local] 2010-02-10 16:08:08 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:08 EST LOG: connection received: host=[local] 2010-02-10 16:08:08 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:09 EST LOG: connection received: host=[local] 2010-02-10 16:08:09 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:09 EST LOG: connection received: host=[local] 2010-02-10 16:08:09 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:10 EST LOG: connection received: host=[local] 2010-02-10 16:08:10 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:10 EST LOG: connection received: host=[local] 2010-02-10 16:08:10 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:11 EST LOG: connection received: host=[local] 2010-02-10 16:08:11 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:11 EST LOG: connection received: host=[local] 2010-02-10 16:08:11 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:12 EST LOG: connection received: host=[local] 2010-02-10 16:08:12 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:12 EST LOG: connection received: host=[local] 2010-02-10 16:08:12 EST FATAL: password authentication failed for user "postgres" 2010-02-10 16:08:12 EST LOG: connection received: host=[local] 2010-02-10 16:08:12 EST LOG: incomplete startup packet My question regarding a potential consequence of this is posted here: http://stackoverflow.com/questions/2238954/mdb2-says-connection-failed-db-logs-say-otherwise , but I didn't realize this was happening when I asked that question, and I figured this [part of the] problem is for SF. Edit: I can connect to the database and manipulate things normally with the psql CLI and the postgres user.

  Read the article

• New SBS 2011 installation (not migration) in an existing 2008 R2 domain

  - by Tong Wang

  My current network setup has two servers: a Windows 2008 R2 with TMG 2010 as edge firewall (TMG server), a second 2008 R2 with DC, DNS and Hyper-V roles (DCDNS server). I was trying to install SBS 2011 as a child partition on DCDNS, first I installed SBS 2011 in English and did the migration successfully. However, later on, I found that I can't change the display language in SBS 2011 once it's installed (but the clients require a different language), so I had to re-install the SBS in a different language. It is during the re-installation that the problem came up: the migration can't be completed with some error message stating "can't access the source server". I re-ran the migration preparation tool, but it didn't make any difference. I wonder if it's because the source server can only be "migrated" once. Since I only need to setup a handful of users and computers, so I decided to do a new install of SBS and picked a different domain name. But I can't get the SBS to connect to LAN: it can't ping other servers, neither can other servers ping the SBS server. I've tried to stop the DC/DNS services on DCDNS and restart SBS, but with no difference. Anyone has idea how to fix this problem?

  Read the article

• Why does Facebook Chat through XMPP protocol on Pidgin Portable not authorize?

  - by Sara Neff

  I heard you can use facebook chat on desktops now. Thats awsome! What i didn't hear is that it is a pain in the butt! Not awsome! I've followed six nearly identical sets of instructions from six different websides, including the one that facebook generates for you, to get facebook chat connected through Pidgin. Its the latest portable version, so from what i hear the plugin is out of the question. Whenever I go to try and connect i get a message saying "Not Authorized" and buttons to either modify the account info, or retry. NOTHING i have done has fixed this, and I can't find anything remotely usefull anywhere. I am running windows xp, and running pidgin (portable) off of a flash drive. Someone please tell me what i have to do. I read about authorizing the chat on my actual facebook page. I'd have tried that if i could find out how to do it, but if its there they hid it good. HELP?!

  Read the article

• Mac Finder: WD My Passport won't mount

  - by Matt

  I really need your help. I have a WD My Passport 650GB (with Firewire and USB). I'm using it for almost a year now and it always worked fine. While underway I simply plug it in via Firewire - at home I connect it to my Airport Extreme to have it available as a network storage. Today I connected the hd to my macbookpro (via firewire) and NOTHING. The hd is starting (clearly making a sound and the power-indicator is flashing) but it won't appear in Finder. I also tried it with USB - no sign. I ran Disk Utility and tried to repair the disk. At first try I got a red error line saying that something is wrong with the "headers". However the repair completed with a success message saying that everything is ok. I also verified the hd. Also with a success message. I did that a few times again and unplugged it in between. Never got the error with the headers again - it's always completing and saying everything is ok. However I can't mount the drive. That is what Disk Utility is showing. Any ideas on that? I really need the files on that hd. thank you in advance!

  Read the article

• Vlan on DD-WRT v24 filesharing without internet

  - by user148888

  I'm planning to do a vlan with shared files without internet. my vlan is working correctly until I could lock the internet but I can not share files only I can ping from 172.168.1.x to 172.168.2.x but not backward. can u help me please?? This is my config. WRT54g DD-wrt v24 vlan0 eth 1,2,3 172.168.1.1/24 vlan1 Wan vlan2 eth 4 172.168.2.1/24(don't want internet here just Lan Conection) Pc (my pc) 172.168.1.10/24 gtway 172.168.1.1 (with internet) Ubiquity Nanostation loco M2 172.168.2.20/24(AP)(connect to eth 4 vlan2)(don't want internet here) Ubiquity Nanostation loco M2 172.168.2.21/24(Client)(don't want internet here) Friend pc 172.168.2.115/24(connected from the client)(don't want internet here) Any Help Please.. ![Lan Map][1] ![Vlan Config1][2] ![Vlan Config2][3] ![Vlan Config3][4] ![Command to block internet][5] [url=http://imageshack.us/photo/my-images/194/lanxl.jpg/][img=http://imageshack.us/a/img194/4197/lanxl.th.jpg][/url] [url=http://imageshack.us/photo/my-images/600/commandmf.jpg/][img=http://imageshack.us/a/img600/9530/commandmf.th.jpg][/url] [url=http://imageshack.us/photo/my-images/811/57398524.jpg/][img=http://imageshack.us/a/img811/1917/57398524.th.jpg][/url] [url=http://imageshack.us/photo/my-images/717/48064277.jpg/][img=http://imageshack.us/a/img717/829/48064277.th.jpg][/url] [url=http://imageshack.us/photo/my-images/685/21456517.jpg/][img=http://imageshack.us/a/img685/256/21456517.th.jpg][/url]

  Read the article

• MS Excel 2010 - Using DSN + 32 bit drivers

  - by Kristiaan

  I need some advice as im running into a problem and so far i have been unable to find a solution. We have a set of reports developed in MS Excel that use DSN file to connect to data sources to retrieve data, these work fine on 32 / 64bit systems, however we are moving to a terminal server environment using windows 2008 R2 64Bit. The reports fail to run using the DSN's within this environment if we only have the 32bit drivers installed and configured in the ODBC settings, the minute we install the 64Bit drivers the software works. Is there a way / Method of getting Excel or the DSN file to NOT use the 64Bit driver, but force it to use the 32bit driver. ANSWERED - But due to low user score i cannot "answer" my own question... Sadly there is no way to-do what i want to-do, without a lot of very nasty and not 100% perfect reg hacks. If you need to access 32bit ODBC data sources the application in question has to be 32Bit. here is a link to just one forum post i found relating to this type of problem, it appears the only way i would be able to accomplish this is to remove the 64bit version of office and install the 32bit version instead of it. http://social.msdn.microsoft.com/Forums/en-US/accessdev/thread/5108f337-f06a-4518-afe3-d3c1abd040ef/

  Read the article

• Multiple Video Cards - Stuttering

  - by jstawski

  I have two video cards: - XFX PVT84JUDD3 GeForce 8600GT XXX 256MB 128-bit GDDR3 PCI Express x16 SLI Supported Video Card - EVGA 256-P1-N399-LX GeForce 6200 256MB 64-bit GDDR2 PCI Video Card both running the same set of drivers on Windows 7 64-bit. When I work with 2 monitors connected to the 8600GT card everything works smoothly. When I connect the third one to the 6200 then Windows works well and all of a suddon the screens turns black for up to 5 minutes. Then it goes back and at some random interval it goes black again. I can still see the pointer and hit CTRL+ALT+DEL and see the menu to log off, bring the task manager, etc. I've tried changing the 6200 to another PCI slot and the error persists. I've tried connecting 2 monitors only one to each card, same problem. Tried swapping them, mixed and matched the monitors to see if it was a problem with the monitor and my conclusion was that it is not the monitor. The problem also occurred with Vista 64 as well. What could be generating this problem? Can it be the fact that they are different interfaces? Maybe the Motherboard? Should I change something on the BIOS? What do you guys think?

  Read the article

• Create image (EBS AMI) takes forever - possibly caused MySQL Server to break?

  - by fuzzybee

  I'm trying to create an EBS AMI from my running EC2 instance to reuse my LAMP fully configured (for my needs). I got my website up and running yesterday on this EC2 instance my MySQL was working fine until this morning (it's not that difficult to install LAMP thanks to yum so I can't see how I could go wrong with this; having said that, it's always difficult for one to realise his own errors) I have seen "Loading, please wait ..." for a few hours now. How do I know whether this is completed or its progress? Shortly after I tried to create the AMI image from my EC2 instance, I encountered database connection error can't connect to local mysql server through socket '/var/lib/mysql/mysql.sock' I was able to restart mysqld at first. But database connection was down again. This time, I could not restart mysqld anymore. It shows MySQL Daemon failed to start. Could my attempt to create the AMI by any chance cause the MySQL server to reboot or corrupt? I did a lot of searched and have done the following although I think I shouldn't have to do any workaround for MySQL server to work here chown -R mysql.mysql /var/lib/mysql/ I also found this workaround but I'm very reluctant to follow due to my belief and the fact I would need to understand this problem first. Any help would be greatly appreciated. Getting back to searching for a solution for the MySQL server problem ... Thanks, Eric

  Read the article

< Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >