Search Results

Search found 1404 results on 57 pages for 'ati radeon'.

Page 51/57 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• Can I have a single solid state drive and a RAID array on the same machine?

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Tooltips shadow stuck on desktop

  - by faulty

  I tends to get this problem from time to time. The tooltips with a shadow appearing on top of everything. It's the shadow of the tooltips not disappearing after the tooltips disappear. The last one I had the tooltips was from the wifi connection list at the systray. This problem also happen to me on another computer. Both running Win7 with ATI gpu. I found this similar post Menu command stuck on screen but none of the solution helped. In fact the "Fade or slide tooltips into view" has been unchecked from the beginning. Ending task of "dwm.exe" also doesn't help. So far the only way to resolve this by restarting window. I can't post picture yet, so can't show any screenshot. Edit: Just tested a few more trick which doesn't work. 1. Turn of aero 2. Hibernate 3. Switch main display to external display and switch back. 4. Change resolution

  Read the article

• Laptop recommendation - Portable Gaming

  - by ivan

  So, I'm looking for a new laptop (http://superuser.com/questions/116869/toshiba-satellite-u500-totally-damaged-lcd). My requirements for a new Laptop are: -good keyboard(illuminated) and touchpad (multi-media keys included, should be better than toshiba u500) -good graphics card, with system rating of 6.3 and up for gaming graphics (my Toshiba U500 has 6.3). I used to run some heavy games on my Toshiba U500 with ATI Mobility Radeon 4570 with 512 mb VRAM but the framerates are not that nice on high settings. -Decent CPU but I think all new Core i3, i5, i7 can run most of recent resource intensive games (My Toshiba U500 has a Core 2 Duo T6500, 2.13 Ghz) I'm also looking for a long-term reliability, good sound quality, lots of fast RAM of-course(4GB DDR3 - 1066Mhz and up) and a clear looking LED screen with a decent resolution. (I can accomodate a laptop with screen size of 13-inch upto 15.6 inch, and I don't want it to be heavy because I might be taking it outdoors) I'm actually impressed when I saw HP Pavilion DV6t but the screen resolution seems to be a little too small for 15.6 inch. The Pavilion DV3 are also good but I want to know if there other options. Looking for some opinions.. Thanks. :D

  Read the article

• Poor gaming performance with hyper-v installed in windows 8

  - by SnowCrash

  I am getting very poor gaming performance on my Windows 8 host OS with Hyper-V installed but no guest machines running. For example World of Tanks reports 60-70 FPS without Hyper-V installed and 4-14 FPS with it installed. A similar, dramatic, hit is observed in several other games so the issue is not WoT specific. To make the point clear, I am not trying to run games in a virtual machine. I don't even have a VM running while observing this effect. I simply have the Hyper-V feature installed. My system specs: AMD Phenom II 965 (3.4 GHz) AMD Radeon 6950 2GB (XFX Double D HD-695X-CDFC) 16GB DDR3 1333 AMD 790GX chipset Mainboard (Gigabyte GA-MA790GPT-UD3H) I have tried every AMD driver from 12.8 to the current 12.11beta8, virtualization is enabled in the BIOS settings, the onboard 3300HD video device is disabled in BIOS and I have read the MSDN blog entry here regarding a similar issue in Server 2008 that was resolved in 2008 R2 (and hopefully not regressed in Win 8). I'd like to be able to use Hyper-V for development and testing at home (I am a sysadmin/software developer professionally). If, however, I can't also use my home system for entertainment I'll have to scrap those plans.

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you.

  Read the article

• Xorg eating up too much RAM on Ubuntu 9.10 box

  - by Yang

  Xorg is eating up 444MB of 2GB total RAM on my Ubuntu 9.10 x86_64 machine with nvidia drivers installed for the nvidia G86 (GeForce 8300 GS). top shows: top - 18:21:41 up 6 days, 2:40, 9 users, load average: 0.46, 1.12, 1.22 Tasks: 266 total, 3 running, 262 sleeping, 1 stopped, 0 zombie Cpu(s): 8.4%us, 2.0%sy, 0.0%ni, 89.1%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2055736k total, 1965136k used, 90600k free, 3952k buffers Swap: 979924k total, 979908k used, 16k free, 102636k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 1432 root 20 0 1154m 442m 7492 S 8 22.0 32:56.97 Xorg 18462 yang 20 0 1001m 219m 8356 S 0 10.9 5:13.25 chrome 24099 yang 20 0 865m 83m 13m S 0 4.2 0:06.91 chrome xrestop shows: xrestop - Display: :0.0 Monitoring 47 clients. XErrors: 0 Pixmaps: 40430K total, Other: 142K total, All: 40573K total res-base Wins GCs Fnts Pxms Misc Pxm mem Other Total PID Identifier 1c00000 21 46 1 19 697 9128K 18K 9146K 3169 x-nautilus-desktop 1000000 4 3 0 17 194 9000K 4K 9004K 3134 gnome-settings-daemon 1600000 51 2 1 25 1100 7648K 28K 7676K ? compiz For comparison, here's my other Ubuntu box, which also has compiz etc. enabled but with ATI RV370 (Radeon X300SE): top - 18:18:18 up 58 days, 4:27, 9 users, load average: 0.00, 0.00, 0.00 Tasks: 224 total, 1 running, 223 sleeping, 0 stopped, 0 zombie Cpu(s): 0.3%us, 0.3%sy, 0.0%ni, 98.8%id, 0.5%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1024964k total, 987124k used, 37840k free, 247012k buffers Swap: 2048276k total, 94296k used, 1953980k free, 264744k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 24324 yang 20 0 61936 35m 6364 S 0 3.5 4:35.84 nxagent 1768 ntop 20 0 190m 32m 5388 S 1 3.2 283:36.15 ntop 1178 root 20 0 60588 29m 1788 S 0 3.0 5:48.89 console-kit-dae ... 1315 root 20 0 343m 4956 4020 S 0 0.5 3:43.87 Xorg Any ideas on how to get to the bottom of this? (i.e. not "Log out"/"Reboot") Thanks in advance.

  Read the article

• Opera 10.5 RAM usage and Google Reader?

  - by David

  Hi all, Today I upgraded to Opera 10.5 from Google Chrome and I have two really important questions about it. 1) Is it normal for it to use SO MUCH RAM!!!!? Closing tabs doesn't help, but opening new ones add on to the usage. I can have just 4 tabs open and it goes up to the 300MB mark and I only have 1.5GB in my laptop, 596MB of it used by the graphics card so this really unacceptable. Is there a way to fix it? 2) Why does Google Reader feel so slow and unresponsive on it? It lags so bad when I just try scrolling through the page. I know Opera is known for being really smooth while scrolling through pages. There's also a white bar at the bottom of the page that I can get rid of. It blocks the "Next" and "Previous" buttons. The test between articles is also sort of intersecting each other and that just looks completely unattractive and that's something i'm not used with any web browser. I realize there's a built-in RSS reader, but it doesn't sync across multiple computers and is very late at updating. Here are my specs: Windows 7 Ultimate (x86), Intel Pentium M 1.86 GHz, 1.5GB RAM, ATI Mobility Radeon X600 (64MB dedicated, 596MB shared)

  Read the article

• Blender refuses to start

  - by Sekhemty

  I'm trying to run Blender under Linux, but I'm unable to do that, whenever I try I get some errors. I'm using Kubuntu 12.04 with KDE 4.11.1. This is my video card: ~$ lspci | grep VGA 01:00.0 VGA compatible controller: Advanced Micro Devices, Inc. [AMD/ATI] RV610/M74 [Mobility Radeon HD 2400 XT] I used to have installed the fglrx proprietary Catalyst drivers, but lately they gave me some system-wide problems and I had to revert to the open source Mesa drivers (I don't think that these details are important, but just in case, the whole story is here). Whit the fglrx drivers Blender was running fine, but now, whenever I try to start it, I get this error message (some parts are in italian, but I think that they are easily understandable): ~$ blender connect failed: No such file or directory Writing: /tmp/blender.crash.txt Errore di segmentazione (core dump creato) The content of /tmp/blender.crash.txt is as follows: # Blender 2.68 (sub 5), Revision: 60150 # backtrace /usr/lib/blender/blender() [0x877a41f] [0xb7756400] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(_ZN4llvm3ARM8SPRClassC1Ev+0x15) [0xa8f4a9d5] /usr/lib/i386-linux-gnu/libLLVM-3.0.so.1(+0x25ca48) [0xa8eefa48] /lib/ld-linux.so.2(+0xeeab) [0xb7765eab] /lib/ld-linux.so.2(+0xef94) [0xb7765f94] /lib/ld-linux.so.2(+0x12fa6) [0xb7769fa6] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/ld-linux.so.2(+0x127f4) [0xb77697f4] /lib/i386-linux-gnu/libdl.so.2(+0xbe9) [0xb4ff9be9] /lib/ld-linux.so.2(+0xeccf) [0xb7765ccf] /lib/i386-linux-gnu/libdl.so.2(+0x133a) [0xb4ffa33a] /lib/i386-linux-gnu/libdl.so.2(dlopen+0x47) [0xb4ff9c97] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x3cbf0) [0xb7717bf0] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x4079d) [0xb771b79d] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(+0x1a3aa) [0xb76f53aa] /usr/lib/i386-linux-gnu/mesa/libGL.so.1(glXQueryVersion+0x2e) [0xb76f0cee] /usr/lib/blender/blender(_ZN15GHOST_WindowX11C1EP15GHOST_SystemX11P9_XDisplayRK10STR_Stringiijj18GHOST_TWindowStatei25GHOST_TDrawingContextTypebbt+0x11c) [0x8f54aec] /usr/lib/blender/blender(_ZN15GHOST_SystemX1112createWindowERK10STR_Stringiijj18GHOST_TWindowState25GHOST_TDrawingContextTypebbti+0xd7) [0x8f4f4a7] /usr/lib/blender/blender(GHOST_CreateWindow+0xb6) [0x8f4cf86] /usr/lib/blender/blender(wm_window_add_ghostwindows+0x205) [0x8799be5] /usr/lib/blender/blender(WM_check+0x50) [0x877b670] /usr/lib/blender/blender(wm_homefile_read+0x111) [0x87859f1] /usr/lib/blender/blender(WM_init+0xd2) [0x8787872] /usr/lib/blender/blender(main+0xe6e) [0x873848e] /lib/i386-linux-gnu/libc.so.6(__libc_start_main+0xf3) [0xb4e694d3] /usr/lib/blender/blender() [0x8778a99] The only thing that I can guess from this report is that the mesa drivers are somewhat involved, as I already suspected, but I don't have a clue on what I need to do to try to solve the issue.

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Least CPU intensive way of streaming your screen on windows?

  - by sinni800

  Hello, sometimes I like capturing my screen for others to see. Only thing: I am playing games while I do it. I have tried a few streaming solutions where Windows Media Encoder coupled with my own Windows server appealed to me most, because I can change resolutions, etc. I also tried ustream coupled with the Flash applet and the Adobe Flash Encoder recording a Camtasia source. Camtasia has the disadvantage though that it shows the green-and-black-alternating borders and can not be targeted fullscreen. I like how xfire does it. But it doesn't work with every game, many are simply not supported. A few thoughts about this: Is there a program which captures like Fraps or XFire (based on Direct3D and OpenGL outputs) and exposes the output to a DirectShow source filter? Which brings me to: Is there hardware accelerated capturing directly from the graphics card? Maybe including direct encoding with help from OpenCL? Modern graphic cards decode BluRay content directly for example. I should have a modern enough graphics processor for this to be possible (see below). If using Windows Media Encoder: Which are the least CPU intensive settings? Which codec? Is there a newer codec than Windows Media 9? Is it less CPU intensive? I only have 7, 8 and 9 inside the Encoder Could the performance be massively increased by having a Quad-Core CPU (see below)? Bandwidth is no problem up to 1000 to 1500 kbit/s (I have 2048). My Computer specs: Intel Core 2 Duo E8400 4 GB DDR2-800 Ram Ati Radeon HD5770 Using Windows 7 Professional

  Read the article

• Blue screen issue

  - by Jack

  I received several BSOD's that are recorded in the following logs: Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 50 BCP1: FFFFF95FF8150C10 BCP2: 0000000000000008 BCP3: FFFFF95FF8150C10 BCP4: 0000000000000005 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-20030-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-33025-0.sysdata.xml ~~~~~ Problem signature: Problem Event Name: BlueScreen OS Version: 6.1.7601.2.1.0.256.48 Locale ID: 3081 Additional information about the problem: BCCode: 1e BCP1: 0000000000000000 BCP2: 0000000000000000 BCP3: 0000000000000000 BCP4: 0000000000000000 OS Version: 6_1_7601 Service Pack: 1_0 Product: 256_1 Files that help describe the problem: C:\Windows\Minidump\040412-32729-01.dmp C:\Users\Jack\AppData\Local\Temp\WER-64319-0.sysdata.xml It seems to occur at random. I have gone 2 months without a BSOD, then I have gone a week with 10+ without changing what I am doing. This is my system: Windows 7 Professional 64-bit Gigabyte GA-890GPA-UD3H AMD Phenom II x6 1090T Processor 3.2GHz 8GB Ram(4X 2GB) Radeon HD 7850 2TB HDD Thermaltake 500W PSU I'm not sure about what the BSOD says, it just counts to 100 by 5's then restarts the computer. It happens fast and I have tried to get a picture before but to no avail.

  Read the article

• Windows Bluescreen - atikmpag.sys

  - by Mochan

  Information Name: atikmpag.sys bluescreen (BSOD or BlueScreen of Death) Error code: 0x00000116 Appears when: Playing games, watching videos Can be reproduced: Yes Cause: Graphics Card is the main assumption System Specifications Before we begin - I will inform you of my specifications. OS: Windows 7 x64 Home Edition Model: Dell Inspiron 15R Special Edition (aka Inspiron 7520) (Add 2GB of RAM to the model linked) Hard Drive: 1TB CPU: Intel Quad-Core i7 Sandy Bridge (I think) Processor at 2.10GHz (I think it can be clocked to 3GHz?) RAM: 6GB (I think 1 x 4GB and 1 x 2GB) Display: 15.6" HD (1366x768) Graphics: AMD Radeon HD 7500M 2GB Details So now that you know some basics about my computer, I'll get to the problem. Being an Ubuntu user I hardly use Windows, but occasionally I do. Like to run Skyrim and other games incompatible with Linux and WINE. The new Sims 3 Seasons patch is also now not supported. When playing these two games and other ones, theoretically. I have also heard others saying that while watching HD movies and video series it also happens. While watching the bluescreen as it happens, I see it is the 'atikmpag.sys' error. I have not installed much and nothing significant. I think I have downloaded Skyrim, Firefox and The Sims 3. I haven't done much more... since Ubuntu is definitely the best in comparison! (No hate, just a joke :P). I can reproduce it easily (just by running a game for less than a minute). It is always there each time, but it's never at a specific time or anything. So far I have found that it may be caused by lack of power to the graphics card, or it may be damaged or fried. Since I've had the computer for a mere 4 months (and have had other problems with it also). I have contacted Dell but they are useless beyond belief. Anyone with any information, solutions or details are encouraged to share your knowledge, as it would be immensely appreciated.

  Read the article

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• How can I fix my vista PCs screen resolution and refresh rate

  - by Antony Scott

  I have a media PC running media portal hooked up to my HDTV via HDMI. The TV is a couple of years old now, so only supports 1080i, which is 1920x1080@25Hz. I've got it connected to my PC via a HDMI compatible AV receiver. If I power up the amp (wait for it to boot fully) followed by the TV| and finally the PC, all is well and I get a picture. If I deviate from that sequence, or don't wait for the amp to book up fully, or even switch the amp to another video input (for example, my PS3). The PC sees this and defaults the screen resolution/refresh rate to 1920x1080@60Hz. So, I end up with a blank screen. To fix this I have to use UltraVNC from a PC and change the refresh rate back to 25Hz. So, is there a way to turn off that auto detection, or to manually define what resolution/refresh rates the monitor can do. I'm using the on-board Radeon 3200 video and do not have any of the AMD software installed as it seems to cause problems with video playback. So, I'm looking for a native vista fix, or possible some 3rd party software.

  Read the article

• Resolving a BSOD/CPU/GPU issue...

  - by Christian Sciberras

  Hello all, I'm getting a BSOD / system crash (sometimes the PC just quits without a BSOD). Hardware Specifications cpu: i7 920 2666MHz / 8 cores (not OCed afaik) mobo: Asus P6T SE ram: 2x Corsair CM3X2G1333C9 (64bit DDR3 667MHz) gfx: ATI Radeon HD 5970 1GB (XFX HD5970 BE) os: Windows 7 Ultimate 64 bit (legit) All bios, firmware and drivers are all up to date (as of today). Symptoms Sometimes the PC runs smoothly, sometimes I get this BSOD. The BSOD always happens when I'm doing something related to graphics, such as viewing a video or playing a game. I get to know about the imminent BSOD ~10 seconds earlier; the PC starts freezing occasionally but increasing in frequency and length of lag (I noticed processor usage in creased from Process Monitor). I've tweaked BIOS settings occasionally but afaik, it was in vain. A day or so ago, I reset it to factory settings. BSOD contents The computer has rebooted from a bugcheck. The bugcheck was: 0x00000101 (0x0000000000000019, 0x0000000000000000, 0xfffff88001f35180, 0x0000000000000004). 15-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 4 23-12-2010 A fatal hardware error has occurred. Reported by component: Processor Core Error Source: Machine Check Exception Error Type: Internal Timer Error Processor ID: 2 Important The interesting thing is that although the event log (and BSOD screen) blame a "secondary processor", Windows Action Center sometimes blamed the GFX driver (for the same error). Also It is interesting to note that after hibernating my PC, I always get the BSOD.

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• Converting DisplayPort and/or HDMI to DVI-D?

  - by Jeff Atwood

  Newer Radeon video cards come with four ports standard: DVI (x2) HDMI DisplayPort If I want to run three 24" monitors, all of which are DVI only, from this video card -- is it possible to convert either the HDMI or DisplayPort to DVI? If so, how? And which one is easier/cheaper to convert? I did a little research and it looks like there isn't a simple "dongle" method. I found this DisplayPort to DVI-D Dual Link Adapter but it's $120; almost cheaper to buy a new monitor that supports HDMI or DisplayPort inputs at that point! There's also a HDMI to DVI-D adapter at Monoprice but I'm not sure it will work, either. AnandTech seems to imply that you do need the DisplayPort-to-DVI: The only catch to this specific port layout is that the card still only has enough TMDS transmitters for two ports. So you can use 2x DVI or 1x DVI + HDMI, but not 2x DVI + HDMI. For 3 DVI-derived ports, you will need an active DisplayPort-to-DVI adapter.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• After update to Windows 8.1 brigthness isn't working (changing)

  - by Bibo

  I just update my Windows 8 to Windows 8.1 by Windows Store and I have some problems. My notebook is Acer Aspire Timelinex 3820TG and I know it's little old for Windows 8 but I install them and works fine (I updated my HDD to SSD). Now I just updated Windows and I have problem with changing brightness on my dedicated graphic card (Ati HD 5650). First I can changing brigthness with fn + keys but It just changing level in OS. No change in real. I tried reinstall drivers, install drivers for my card from Acer with compatibility to Windows 7 and without change. When I switch to integrated card changing brightness works. I think the problem is with drivers but I don't know how to get it working. Thanks for help Bonus question: I have another problem (but this one is not so important). Does anyone knows what msietxghh.exe is doing? Everytime when my system runs (after update) I get message that this program stops working but I just cancel and looks everything works fine.

  Read the article

• How can I fix video tearing and pausing on Windows XP Flash videos?

  - by xvs

  I have what should be a reasonably fast PC: it's a Quadcore Intel 6600 at 2.4 GHz, 4MB of RAM, an ATI 3800 series video card and an LG L246WP monitor, which I selected particularly because it was supposed to work well with video and have no trails or other artifacts. So I should be able to play video with no problems. And I can, as long as that video isn't Flash video. With Flash, what I see is tearing, especially during pans, and pausing -- every few seconds the video pauses for about 300ms while the sound stays continuous. I tried going into the video card setup and changing vertical sync, pulldown detection, windows media video acceleration, deinterlacing and triple buffering. but no combination of settings I've tried has changed or corrected the problem in any way. I've also tried enabling and disabling hardware acceleration in the Flash settings, to no avail. This problem happens whether or not the video is streaming or has fully streamed in before playing. So, what can I do? Is this just a flash issue or is there a way to get it to work?

  Read the article

• x display problems in centos 5.5

  - by John Ruiz

  I have a Dell E510 desktop with a geForce 7200 instead of the ATI x600 it came with. I have attempted to install CentOS 5.4 x86_64 (DVD), CentOS 5.5 (net install), and CentOS 5.5 x86_64 (DVD). Gnome desktop. All of these run into the same issue. When I put the DVD into the machine and reboot, the installer begins and I select "graphical install". I see text that say anaconda is starting, and then my screen goes nuts. It's not black, but rather a screen full of diagonal stripes or multiple colors. So I attempted to do a text install of CentOS 5.5 (DVD) and got it installed. When I booted for the first time, I logged into the virtual console and started X (startx). The desktop came up and it already had the display properties GUI up. I changed it from 800x600 to 1680x1050, saw that there were updates available, installed them, and then rebooted. When I start X from the virtual console this time, I get exactly the same display problem as I described before. Does anyone know what might be causing this and what I can do about it? edit: I should also mention that I'm capable of installing Windows 7 and Ubuntu 10.04 onto this machine with absolutely no issues at all.

  Read the article

• Silent install FirePro v4900 Driver on Windows Embedded 7 Standard

  - by Birgit_B

  I'm trying to install the Drivers for a FirePro v4900 on a Windows Embedded 7 Standard 64bit OS. I want the system to be as small as possible, so i would rather not install the whole catalyst control center, but only the necessary drivers. Because the installation should be accomplished absolutely unattended, the installation process of the FirePro-Driver should also be done without any user interaction. I see two possible solutions for the Problem: Install only the Drivers: Is it possible to solely install the necessary drivers? How would i achieve that? This solution would be the preferred one, because of the smaller footprint. Silent custom install the provided "FirePro_8.911.3.3_VistaWin7_X32X64_135673.exe" (found at ATI FirePro™ Driver). Is there a way, to do that? Thank you in advance for your support! Update: I managed to accomplish a silent installation. I extracted the contents of the above mention installer-file and ran \$_OUTDIR\Bin64\Setup.exe -Install. (There are some other Parameters, just run Setup.exe /?). But i couldn't achieve to just install the drivers without the Cataclyst Control Center, and it seams the Control Center has some unfulfilled dependencies and so it crashes...

  Read the article

• There's no sound on Ubuntu with an Intel HDA onboard chip and Realtek ALC1200 codec.

  - by Hanno Fietz

  For a while now, my sound has not been working in Ubuntu. It used to play OK, but after some upgrade (might have been distro upgrade to 9.10), it stopped working. I'm currently running 10.04 on an amd64 architecture. I'm using the builtin audio on a Foxconn motherboard, it's an ATI / Intel HDA chip with an Azalia controller, apparently it's using the Realtek ALC1200 codec. All the gory details here. I found a nice sound troubleshooting tutorial here, which is well-written and pretty extensive, however, I fail to look up the supported "models" for my soundcard. The troubleshooting page says to look for a section giving the codec used by your soundcard, which looks like this for me: !!HDA-Intel Codec information !!--------------------------- --startcollapse-- Codec: Realtek ALC1200 Then, I'm supposed to lookup the models for that codec in the file Documentation/ALSA-Configuration.txt in the appropriate directory of ALSA's git repository. Mine actually pointed me to a separate file, Documentation/HD-Audio-Models.txt, which, for my driver version is located here and contains no section related to ALC1200 codecs. I tried putting the driver options probe-mask=1 and model=auto in a config file for modprobe, as suggested elsewhere, but this just lead to snd-hda-intel not able to load at all anymore. I also tried installing the linux-backports-modules-alsa package for my kernel, because the description sounded promising, but that didn't change anything, either.

  Read the article

• Expanding to dual video cards

  - by Anthony Greco

  I know a lot of factors can go into play here, so I will list my current hardware and setup: MOBO: GIGABYTE GA-890FXA-UD5 [http://www.newegg.com/Product/Product.aspx?Item=N82E16813128441] Processor: AMD Phenom II X6 1090T Black Edition Thuban 3.2GHz [http://www.newegg.com/Product/Product.aspx?Item=N82E16819103849] Ram: G.SKILL Ripjaws Series 16GB (4 x 4GB) [https://secure.newegg.com/NewMyAccount/OrderHistory.aspx?RandomID=4933910872745320111128011418] Current video card: EVGA 01G-P3-1366-TR GeForce GTX 460 SE [http://www.newegg.com/Product/Product.aspx?Item=N82E16814130591] OS: Windows 7 Ultimate x64 Currently I can run 2 monitors just fine in my setup. However, I want to upgrade this to 4 monitors. My question is, what is the best way to do this? I remember in the past reading I need the same type of video card, however would any GeForce GTX work, or do i need that very specific model (EVGA 01G-P3-1366-TR GeForce GTX 460 SE)? Are there any issues I should be aware of before I order 2 new monitors and a video card? Are there video cards better setup for this? I know NVidia offers SLI, however I do not know if my mobo is compliant. My mobo also offers CrossFireX configuration, though from what it says only Radeon are compliant. Any suggestions / feedbacks on my best route with my current setup is appreciated. Even if you suggest buying 2 new identical video cards, as long as you can mention which and why that is better I really appreciate it. Note: I really do not do any gaming. I sometimes do some 3D work in Unity and very rarely in Maya. Besides that I mostly do all my computer work in Visual Studios and Photoshop. I however need the 2 extra monitors because I monitor sometimes 5 remote desktops at once and switching on only 2 is becoming a very big pain. Also seeing 3 side by side while I work on the 4th will be very helpful. Again, I appreciate any feedback, as I have googled a bunch and just want to make sure what I buy will work.

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57  | Next Page >