Search Results

Search found 3087 results on 124 pages for 'chi ping lee'.

Page 51/124 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

• routing traffic between two network cards through firewall

  - by RubyFreak

  I'm trying to test a network device (firewall) using a Linux box, with two network cards, one interface connected to the WAN zone and another interface to LAN zone. The configuration is similar with that |ETH0| <-> | FW | <-> ETH1 So from both interfaces I'm able to ping the respective firewall interface. But i'm not able to fire something like: ping -I eth0 ip.from.eth1 and to get any answer. Is that possible or should the linux network namespace solution or user level tcp stacks (VMs are out of question)

  Read the article

• Server 2008 won't run executables from CMD prompt without .exe extension

  - by Dan

  On one of our production server 2008 boxes, I cannot run executables from a CMD prompt without supplying the full filename, including the '.exe' extension. For example, when running "java" produced the usual "is not recognized as an internal or external command" message, I assumed I had borked the path and/or java_home variables. However, even navigating to the %java_home%\bin directory and typing "java" produced the same error. If I type "java.exe" instead, all works perfectly. The problem does not only affect java.exe. Even Microsoft executables suffer the same problem -- ping fails, ping.exe works; ipconfig fails, ipconfig.exe works; manually created batch file 'test' only works when invoked explicitly as 'test.bat'. Any bright ideas?

  Read the article

• Basic networking: Centos Server Router + Ubuntu Client setup.. unable to access outside world from client

  - by ale

  I am trying to set up my Centos Server with two NICs as a router. eth0 is connected to the outside world and eth1 is connected to an Ubuntu client. Here's eth0 on the server: DEVICE=eth0 BOOTPROTO=dhcp ONBOOT=yes TYPE=Ethernet eth1 on the server: DEVICE=eth1 BOOTPROTO=static IPADDR=192.168.0.10 # a free address on my network ONBOOT=yes TYPE=Ethernet My server has IPv4 packet forwarding turned on and my iptables only contains: # iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE # iptables --append FORWARD --in-interface eth1 -j ACCEPT My Ubuntu client has this in its /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp gateway 192.168.0.10 but I can't get an Internet connection from the server for my client. I can't even ping my server from the client: $ ping 192.168.0.10 Destination Host Unreachable

  Read the article

• WSUS is not using Akamai CDN for syncronisation source

  - by Geekman

  I've just installed a WSUS onto our network, and I'm currently doing the initial sync. I've found that WSUS does not seem to be talking to an Akamai cache, but rather with MS directly. This is contrary to what I've always thought regarding Windows Update traffic. Tcpdump of our WSUS server doing initial sync... As you can see it's speaking with 65.55.194.221. For me to speak to this IP, I have to go over international transit links. Which is of course not ideal. 8:42:31.279757 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4379374:4380834, ack 289611, win 256, length 1460 18:42:31.279759 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4380834:4382294, ack 289611, win 256, length 1460 18:42:31.279762 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [.], seq 4382294:4383754, ack 289611, win 256, length 1460 18:42:31.279764 IP 65.55.194.221.https > XXXX.XXXX.XXXX.XXXX.50888: Flags [P.], seq 4383754:4384144, ack 289611, win 256, length 390 18:42:31.279793 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4369154, win 23884, length 0 18:42:31.279888 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4377914, win 23884, length 0 18:42:31.280015 IP XXXX.XXXX.XXXX.XXXX.50888 > 65.55.194.221.https: Flags [.], ack 4384144, win 23884, length 0 And yet, if I ping download.windowsupdate.com it seems to resolve to a local (national) Akamai node, just fine: root@some-node:~# ping download.windowsupdate.com PING a26.ms.akamai.net (210.9.88.48) 56(84) bytes of data. 64 bytes from a210-9-88-48.deploy.akamaitechnologies.com (210.9.88.48): icmp_req=1 ttl=59 time=1.02 ms 64 bytes from a210-9-88-48.deploy.akamaitechnologies.com (210.9.88.48): icmp_req=2 ttl=59 time=1.10 ms Why is this? And how can I change that (if possible)? I know that I can manually specify a WSUS source to sync with instead of pick the default MS Update like I currently have... But it seems like I shouldn't have to do this. NOTE: I've haven't confirmed if a WUA speaks with Akamai, just looking at WSUS as all WUAs will use our internal WSUS from now on. We'll be looking to join an IX shortly with the hopes of peering with an Akamai cache and have very fast access to Windows Updates. Before I let this drive my motivations for an IX at all I want to first confirm it's actually possible for WSUS to speak with an Akamai cache. I know this is somewhat networking related, but I feel like it has more to do with WSUS than anything, so someone who knows WSUS better than me will likely be able to figure this out.

  Read the article

• adding a route entry to linux routing table

  - by netg

  hi, I have two systems with ip address say 64.103.56.1(A)(Dev name -wlan0) and 64.103.225.18(B),now what i want is , everytime I ping B from my system A, it has to be routed via a router say with address 10.0.0.251(C)(I want this to be my next hop to reach B) , but this router is on a different subnetwork than the two systems.How do I do this? /* Things I tried: I used 'route add -host B gw C wlan0', and got an error saying " no such process exist or no such device found". Tried ping C and traceroute and found the gw addr at my side is some 63.103.236.3(D), so added another entry route add -host C gw D wlan0, I was able to do this without any error! */

  Read the article

• TTL and traceroute showing different values for same domain

  - by Cray XT3

  y am i getting two different output for tracert and ping. Ping Result showing total hops of 20 and tracert showing 8. default ttl value on my linux machine 64,icmp echo reply ttl value 44. 64-44=20 but tracert is showing only 8 hops. What can be the reason? If tracert is implemented using ttl then why am i getting different values for same domain.no matter how many times i tried. Fo google and google services,ttl value and tracrt are same,but for other domains its different.

  Read the article

• Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

  - by tomdee

  I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

  Read the article

• diagnostic software for wifi adapter

  - by Nathan Fellman

  I'm having trouble with my wifi connection. Is there any software out there that can help me determine if the problem is in the drivers or in the hardware? Regretfully, I'm working on Vista Edit: The problem I'm having is that the Vista reports that the wireless radio is connected, shows an IP and all, the router also shows that the computer is connected, but there's no connectivity. I can't logon to the router, and I can't even ping it. When I ping it I get the response: General Failure I have tried connecting with and without various wireless security protocols. I have tried disabling the wireless adapter and re-enabling it from the Device Manager I have tried updating the driver None of this has helped. When I connect via Ethernet (with a cable, that is), everything works fine. Edit: I'm not using any firewall on the computer, that I'm aware of. The IP address for the WIFI adapter is similar to the one for the LAN adapter. They differ by one.

  Read the article

• Setting a wireless access point on Ubuntu server 11.10

  - by Solignis

  I am trying to setup a wifi access point with my Ubuntu server. I have managed to get my phone to connect the wireless and now it get a DHCP lease. Though it still cannot ping out or get pinged by anything on my network. I am prety sure my problem is iptables, but I not sure what would be wrong. Here is what my rules look like. (The ones pertaining to the bridge interface) # Allow traffic to / from wireless bridge interface iptables -A INPUT -i br0 -j ACCEPT iptables -A OUTPUT -o br0 -j ACCEPT I am guessing my rules are a little lean, the bridge exists on the same subnet as everything else on my network, I am using a 10.0.0.0/24 subnet. EDIT Oh yeah I should mention also, when I do a ping test, I get Destination Host Unreachable as the error.

  Read the article

• Shared resources in Windows Server 2008 were lost

  - by user316687

  We have an Oracle database in Windows Server 2003, which has its archived redo logs stored on a shared resource of a Windows Server 2008: \\192.168.1.189\d$\folder_for_archivedlogs However, according to Oracle's alert.log, at 10:01 p.m that shared resource got lost and the database was inaccessible. From my Windows Server 2003, on Windows Explorer, I couldn't access that shared resource, but I got a response when I did ping 192.168.1.189. I reviewed all the Event Logs on that Windows 2008, but there is no error at 10:00pm or 11:00pm. Has anyone seen some similar case before? (Shared resources get lost, but you still can ping the server and there are no error events in the Event Logs).

  Read the article

• How to enable RDP to a Server 2008 R2 on another network? VM network

  - by Saariko

  I have a W2008 R2 installed on a different network (I am on 192.168.0.x - new server on 192.168.3.x) I had trouble ping and RDP to it. I disabled the firewall to test the connection: and that opened the ping feature but I still can not RDP to that machine. the allow remote access is enabled As per sinni80 idea - Here is the error message The networks are divided by a Fortigate 60-B router - 2ndy interface for the gateway is 192.168.3.254 (and pingable from all) any to any rule on both networks is in place. As per Joe Schmoe idea - I am able to RDP to 192.168.3.1 from 192.168.3.3 (which is on the same network) Data to add: - The servers are on a VM host, each of the servers has 2 nics one is DHCP enabled into the 192.168.0.x network 2nd is static IP in the 192.168.3.x -- Further information: The network 192.168.0.x - are on a domain network (active Directory) The network 192.168.3.x - are grouped in a workgroup What should I check more please?

  Read the article

• VMware 1.0.1 Windows7 - Ubuntu hostnames

  - by Kyle K

  I'm trying to run Ubuntu as the guest OS using VMWware 1.0.10 with Windows 7 Ultimate as the host OS. I had this set up previously with Win XP as the host OS and in fact I'm using the same .vmx My problem is I can't get either Win7 or Ubuntu to be able to ping the other by hostname. After installing Samba and Winbind on Ubuntu, I was able to get this working when under WinXP, but for some reason I can't get it to work under Win7. I can ping by IP Address, and the guest OS even shows up by hostname under the Windows networking panel (but of course I can't do anything with it), but pinging using short hostnames just won't work. Also, Win7 firewall is turned off completely.

  Read the article

• How to integrate monit into web app deployment process

  - by shabunc

  I have: Tomcat with webapp deployed via mvn tomcat:redeploy. Monit, pinging the host and restarting server if ping failed. The thing is there in a moment during the redeployment when ping will fail - and this is normal, actually. So, the question is - what is the best way to teach monit to consider the fact of redeployment and not to confuse it with "real" black outs. This is of course an issue of balance between elegance, ease of implementation and scalability. The most straightforward solution I can think of - is just to shutdown monit before deployment and start it up after once again. But this if far from elegance I guess.

  Read the article

• Virtualbox - routing subnet to bridge adapters

  - by user42384

  Hello, I have set up a Debian Lenny box with 3 vbox Lenny machines running eth0 of the host in bridged mode (on virtualbox 3.1.6). When testing in my local LAN, this all worked perfectly well and traffic flowed to and from the IPs of the virtual machines as it should. However, now that it's in its co-lo home, the networking setup is a bit different, and I'm unable to get traffic to flow to the vboxes properly. Specifically, the host has its own Primary IP, and I have a separate subnet of 8 (6 usable) IPs routed to the box for use by the vboxes. So, eth0 on host is: Machine IP: 2x.x.x.137 Gateway IP: 2x.x.x.138 Subnet Msk: 255.255.255.252 Subnet for vboxes is Subnet: 2x.x.x.240/29 Netmask: 255.255.255.248 vbox1 is configured to 2x.x.x.241 on eth0 as follows: auto eth0 iface eth0 inet static address 2x.x.x.241 netmask 255.255.255.248 Setting up a virtual interface (eth0:0) on the host with one of these subnet IPs allows me to ping to that address only from vbox1, and it allows me to ping vbox1 from the host. I can also ping that virtual interface perfectly well from outside, so the IPs are definitely landing at my machine. It seems I'm missing some sort of routing instruction either on the host or vbox1 to get traffic moving between the subnet and the default gateway, but I can't seem to figure out what it should be, or what glaringly obvious thing i'm missing. Most of my obvious attempts (the gw of eth0, the ip of eth0) were rejected by route command with SIOCADDRT: No such device (eg - i can't find it). I tried setting vbox1 to bridge on eth0:0, but this was not an acceptable device name and VBoxHeadless refused to start. The physical machine does have an unused physical NIC at eth1 that can be used if necessary for something or other. Host machine is running iptables configured by ferm, have experimented with it allowing forwarding for that subnet, but I wouldn't have thought this was necessary given the nature of the virtualbox devices (nor did it actually work). Clearing out all of these rules for a blank iptables set does not resolve the issue. (you can see ferm generated iptables at http://codedumper.com/ojaze) Thanks for any help you can give... Patrick

  Read the article

• Sharing wireless internet connection between 2 Ubuntu 10.04 systems using cross-over cable

  - by Gary

  I have a Lenovo T60 with Ubuntu 10.04 connected with a cross-over cable to a Dell Vostro 1400, also running Ubuntu 10.04. My internet is coming into the Lenovo through an external wireless antennae, and I want to share the internet with the Dell. On the Lenovo: eth0 connection has IPv4 Settings 'Shared to other computers' I can ping the Dell (10.42.43.10) successfully I can use mtr to trace to www.google.com successfully On the Dell: eth0 connection has IPv4 Settings 'Automatic DHCP' I can ping the Lenovo (10.42.43.1) successfully when I use mtr to trace to www.google.com, I can only reach 10.42.43.1 I must be missing some setting, but cannot see what it is; can anyone help me?

  Read the article

• Windows Server 2008 R2 loses ability to connect to network share

  - by JamesB

  I could sure use some help with this one: I've got two Windows Server 2008 R2 x64 Terminal Servers, as well as several 2003 servers (DNS / Wins / AD / DC). On the two 2008 boxes, every now and then they will get in this mode where you can't map a drive to a random server. I say random server because it's not always the same server that you can't map to. Here is a summary of what I can and can't do: net view \\servername Sometimes this works, sometimes it does not. net view \\FQDN This always works. net view \\IPAddress This always works. ping servername Sometimes this works, sometimes it does not. ping FQDN This always works. ping IPAddress This always works. I've been looking all over for a solution to this. It sure seems like Microsoft would have a hotfix by now. The kicker to this is that it sometimes works great, especially after a reboot. It may run for 2 weeks just fine, but all of a sudden it will fail to resolve the remote server name. It will then be this way for a few days, then it might start working again. Also, while it's in the mode of not working, the other servers have no problem getting there. It's just these 2008 R2 Terminal Servers. Setting a static entry in the Hosts file and LMHosts does not make it work. All servers have static IPs and they are registered in DNS and Wins just fine. Here is a long thread on MS Technet of the exact same problem, but they don't have a good solution. Here is their workaround (It was from June of 2010): Good news - a hotfix is in the works and a workaround has been identified: Root cause is that since this is SMB1 all user sessions are on a single TCP connection to the remote server. The first user to initiate a connection to the remote SMB server has their logon-ID added to the structure defining the connection. If that user logs off all subsequent uses of that TCP session fail as the logon-id is no longer valid. As a workaround for now to keep the issue from happening you will want to have the user not logoff the Terminal Server only disconnect their sessions. Any word from anyone out there about a solution? Any help would sure be appreciated. Thanks, James

  Read the article

• All invalid hosts gets resolved to "com.org"

  - by Vi

  vi@vi-server:~$ nslookup nonexistent.itransition.com Server: 8.8.8.8 Address: 8.8.8.8#53 ** server can't find nonexistent.itransition.com: NXDOMAIN vi@vi-server:~$ cat /etc/resolv.conf nameserver 8.8.8.8 It does not exist. The same result from dig nonexistent.itransition.com. vi@vi-server:~$ ping nonexistent.itransition.com PING nonexistent.itransition.com.org (216.234.246.153) 56(84) bytes of data. 64 bytes from 99.f6.ead8.static.theplanet.com (216.234.246.153): icmp_seq=1 ttl=46 time=128 ms 64 bytes from 99.f6.ead8.static.theplanet.com (216.234.246.153): icmp_seq=2 ttl=46 time=128 ms It catches all invalid hostnames? Why? How to prevent?

  Read the article

• IPv6 routing to another interface

  - by Robert

  I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues. When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router. My PC is directly attached to FA 0/1 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything. I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response. I'm running on IOS 12.4. I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert Topology: R1 FA 0/0: 2001:0000:0000:0000::1/52 FA 0/1: 2001:0000:0000:1000::1/52 FA 1/0: 2001:0000:0000:2000::1/52 Loopback 0: 2001:0000:0000:3000::1/52 PC: 2001:0000:0000:2000::2/52 PC plugs directly into FA 1/0 on the router. --- Configuration --- ipv6 cef ipv6 unicast routing interface Loopback0 no ip address ipv6 address 2001:0000:0000:3000::1/52 ipv6 enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000::1/52 ipv6 enable ! interface FastEthernet0/1 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:1000::1/52 ipv6 enable ! interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:2000::1/52 ipv6 enable --- end of config --- --- routing table --- IPV6Lab#show ipv6 route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2001:0000:0000::/52 [0/0] via ::, FastEthernet0/0 L 2001:0000:0000::1/128 [0/0] via ::, FastEthernet0/0 C 2001:0000:0000:1000::/52 [0/0] via ::, FastEthernet0/1 L 2001:0000:0000:1000::1/128 [0/0] via ::, FastEthernet0/1 C 2001:0000:0000:2000::/52 [0/0] via ::, FastEthernet1/0 L 2001:0000:0000:2000::1/128 [0/0] via ::, FastEthernet1/0 C 2001:0000:0000:3000::/52 [0/0] via ::, Loopback0 L 2001:0000:0000:3000::1/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 --- end of routing table ---

  Read the article

• why this routing configuration does not work?

  - by avs099

  I have 2 VMs in HyperV role: first is RRAS - it has 2 interfaces (both manually configured, no DHCP): 192.168.1.110 - "external" one, connected to the router 192.168.10.2 - that's internal interface which other VMs will be using as well also I added VPN connection to our main server - and it gets 192.168.2.136 IP address in 192.168.2.XXX network. And IP route is create on the server as well for this interface. second VM is called KITCHENER. It only has 1 interface 192.168.10.99 / 255.255.255.0, with default gateway set to RRAS server - 192.168.10.2 QUESTION: how can I ping "main server" - 192.168.2.1 - from the KITCHENER server when RRAS server is connected to VPN? please see screenshots with ipconfig /all, route print and ping 192.168.2.1 commands. What needs to be done to get this working? all servers are Windows 2008 R2 if that matters.

  Read the article

• Comunication from Server to Client + Client LAN

  - by Filipe YaBa Polido

  I'm having some trouble with some network setup. I've tried OpenVPN, SocialVPN, Hamachi, still it is not working. This is my setup: Server A: NIC 1 with internet public address, NIC 2 to LAN Client B PC: NIC 1 (192.168.10.2) connects to router 192.168.10.1 Client B Device: 192.168.10.3 (Configured via software, can't do much here) Problem: Server A must connect to cliente device B. (I can install software needed at Client B PC). However... I can't change the router to some model with VPN like Draytek or Cisco :( OpenVPN fails at bridging, PC B can ping Server A, but Server A can't ping Device B, only PC B. What else can I do?!?!?

  Read the article

• Error while trying to configure VLAN with Open vSwitch

  - by Abhishek Chanda

  I am trying to connect a number of VMs using Open vSwitch. The VMs are on two separate physical boxes. Here is what I did: Created two tap devices on one physical host sudo ip tuntap add mode tap tap0 and same for tap1 Bring them up sudo ip link set tap0 up Add them as ports to Open vSwitch (br0 was created as a OVS bridge previously) sudo ovs-vsctl add-port br0 tap0 tag=1 Now I booted the VMs (using VirtualBox) and assigned addresses 192.168.122.11 and 192.168.122.12. Now when I try to ping one VM from another, I get the error Connect: network is unreachable. Since both VMs are connected to the switch on the same VLAN, I expect to be able to ping one from another. What is going wrong here?

  Read the article

• IP issue with Heartbeat & DRBD

  - by adam0345

  I'm in the process of setting up 3-node stacked DRBD, and i'm experiencing a rather bizarre issue. Two nodes are located at the data center, and the 3rd node is located locally. The Primary and Secondary nodes are working as expected, however the 3rd node won't connect to the primary. If I ping the IP provided by heartbeat on the 3rd node it will return 100% packet loss, if I reset networking interfaces, ping will then return a few successful packets, but then stop returning any packets. I can't work out any reason why this would be behaving like this. All nodes are running Debian Squeeze, and the latest version of DRBD.

  Read the article

• How do I remote desktop to my work's Windows box from my Mac at home through VPN?

  - by CT

  I would like to remote desktop from my Macbook to my Work's laptop from home. I connect to the work's network via Cisco VPN. My Cisco VPN clients connects fine in Mac OS X but I am unable to remote desktop. I am also unable to ping my work laptop. The laptop is powered on and not sleeping. I can access it via LogMeIn. If I were to actually pug into our network at the building. I can remote desktop to my work laptop from my Macbook. If I use a Windows virtual machine and connect using the Windows Cisco VPN client, I am able to RDP and ping my work laptop. What is wrong with my OS X VPN connection?

  Read the article

• Relation between Apache and DNS configuration

  - by KayKay

  I configured my DNS (bind9) to accept every subdomain, using a wildcarded 'A' record : *.mydomain.tld. IN A xx.xx.xx.xx I configured Apache to serve some specific subdomains using virtual hosts : <VirtualHost *:80> ServerName sub1.mydomain.tld ServerAlias sub1.mydomain.tld JkMount / sub1JK JkMount /* sub1JK </VirtualHost> when I ping from a remote computer on a subdomain configured in apache I get a response. When I ping on a subdomain that is not configured in apache, the host is not found. I don't understand why apache configuration would affect DNS resolution like this? I would appreciate any information that helps me understand this. Thanks a lot.

  Read the article

• my domain.com is pointing to two different IP addresses

  - by user43726

  Initially my domain , mycompany.com points to this IP: - 123.456.789.101 (sample only) Then i got another VPS and then decided to move the mycompany.com into this new IP/Host: - 987-654-123.123 (sample only) I changed the necessary stuff like DNS, etc. from my domain management panel. But when i ping it : ping mycompany.com , sometimes it gives the first IP, sometimes the second one. Also when i visit the url from the browser, sometimes it loads, sometimes it doesn't. How can i solve this? Please help. Thanks

  Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >