Search Results

Search found 8189 results on 328 pages for 'fedora 16'.

Page 51/328 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • Diagnosing packet loss / high latency in Ubuntu

    - by Sam Gammon
    We have a Linux box (Ubuntu 12.04) running Nginx (1.5.2), which acts as a reverse proxy/load balancer to some Tornado and Apache hosts. The upstream servers are physically and logically close (same DC, sometimes same-rack) and show sub-millisecond latency between them: PING appserver (10.xx.xx.112) 56(84) bytes of data. 64 bytes from appserver (10.xx.xx.112): icmp_req=1 ttl=64 time=0.180 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=2 ttl=64 time=0.165 ms 64 bytes from appserver (10.xx.xx.112): icmp_req=3 ttl=64 time=0.153 ms We receive a sustained load of about 500 requests per second, and are currently seeing regular packet loss / latency spikes from the Internet, even from basic pings: sam@AM-KEEN ~> ping -c 1000 loadbalancer PING 50.xx.xx.16 (50.xx.xx.16): 56 data bytes 64 bytes from loadbalancer: icmp_seq=0 ttl=56 time=11.624 ms 64 bytes from loadbalancer: icmp_seq=1 ttl=56 time=10.494 ms ... many packets later ... Request timeout for icmp_seq 2 64 bytes from loadbalancer: icmp_seq=2 ttl=56 time=1536.516 ms 64 bytes from loadbalancer: icmp_seq=3 ttl=56 time=536.907 ms 64 bytes from loadbalancer: icmp_seq=4 ttl=56 time=9.389 ms ... many packets later ... Request timeout for icmp_seq 919 64 bytes from loadbalancer: icmp_seq=918 ttl=56 time=2932.571 ms 64 bytes from loadbalancer: icmp_seq=919 ttl=56 time=1932.174 ms 64 bytes from loadbalancer: icmp_seq=920 ttl=56 time=932.018 ms 64 bytes from loadbalancer: icmp_seq=921 ttl=56 time=6.157 ms --- 50.xx.xx.16 ping statistics --- 1000 packets transmitted, 997 packets received, 0.3% packet loss round-trip min/avg/max/stddev = 5.119/52.712/2932.571/224.629 ms The pattern is always the same: things operate fine for a while (<20ms), then a ping drops completely, then three or four high-latency pings (1000ms), then it settles down again. Traffic comes in through a bonded public interface (we will call it bond0) configured as such: bond0 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5d inet addr:50.xx.xx.16 Bcast:50.xx.xx.31 Mask:255.255.255.224 inet6 addr: <ipv6 address> Scope:Global inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:527181270 errors:1 dropped:4 overruns:0 frame:1 TX packets:413335045 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:240016223540 (240.0 GB) TX bytes:104301759647 (104.3 GB) Requests are then submitted via HTTP to upstream servers on the private network (we can call it bond1), which is configured like so: bond1 Link encap:Ethernet HWaddr 00:xx:xx:xx:xx:5c inet addr:10.xx.xx.70 Bcast:10.xx.xx.127 Mask:255.255.255.192 inet6 addr: <ipv6 address> Scope:Link UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 RX packets:430293342 errors:1 dropped:2 overruns:0 frame:1 TX packets:466983986 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:77714410892 (77.7 GB) TX bytes:227349392334 (227.3 GB) Output of uname -a: Linux <hostname> 3.5.0-42-generic #65~precise1-Ubuntu SMP Wed Oct 2 20:57:18 UTC 2013 x86_64 GNU/Linux We have customized sysctl.conf in an attempt to fix the problem, with no success. Output of /etc/sysctl.conf (with irrelevant configs omitted): # net: core net.core.netdev_max_backlog = 10000 # net: ipv4 stack net.ipv4.tcp_ecn = 2 net.ipv4.tcp_sack = 1 net.ipv4.tcp_fack = 1 net.ipv4.tcp_tw_reuse = 1 net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_timestamps = 1 net.ipv4.tcp_window_scaling = 1 net.ipv4.tcp_no_metrics_save = 1 net.ipv4.tcp_max_syn_backlog = 10000 net.ipv4.tcp_congestion_control = cubic net.ipv4.ip_local_port_range = 8000 65535 net.ipv4.tcp_syncookies = 1 net.ipv4.tcp_synack_retries = 2 net.ipv4.tcp_thin_dupack = 1 net.ipv4.tcp_thin_linear_timeouts = 1 net.netfilter.nf_conntrack_max = 99999999 net.netfilter.nf_conntrack_tcp_timeout_established = 300 Output of dmesg -d, with non-ICMP UFW messages suppressed: [508315.349295 < 19.852453>] [UFW BLOCK] IN=bond1 OUT= MAC=<mac addresses> SRC=118.xx.xx.143 DST=50.xx.xx.16 LEN=68 TOS=0x00 PREC=0x00 TTL=51 ID=43221 PROTO=ICMP TYPE=3 CODE=1 [SRC=50.xx.xx.16 DST=118.xx.xx.143 LEN=40 TOS=0x00 PREC=0x00 TTL=249 ID=10220 DF PROTO=TCP SPT=80 DPT=53817 WINDOW=8190 RES=0x00 ACK FIN URGP=0 ] [517787.732242 < 0.443127>] Peer 190.xx.xx.131:59705/80 unexpectedly shrunk window 1155488866:1155489425 (repaired) How can I go about diagnosing the cause of this problem, on a Debian-family Linux box?

    Read the article

  • Slow disk transfer rate

    - by Nooklez
    I have problem with slow disk transfer rate. It's static files server for our website. I was making backup of data and noticed that tar is very slow. So I did hdparm -t and... hdparm -t /dev/sda3 /dev/sda3: Timing buffered disk reads: 6 MB in 4.70 seconds = 1.28 MB/sec It's low traffic hour now on our site, so huge I/O traffic is not a reason (iotop show less than 1 MB/s). It's RAID10 setup (2x2 SATA drives). Unit UnitType Status %RCmpl %V/I/M Stripe Size(GB) Cache AVrfy ------------------------------------------------------------------------------ u0 RAID-10 OK - - 64K 1396.96 W ON VPort Status Unit Size Type Phy Encl-Slot Model ------------------------------------------------------------------------------ p0 OK u0 698.63 GB SATA 0 - WDC WD7500AADS-00M2 p1 OK u0 698.63 GB SATA 1 - WDC WD7500AADS-00M2 p2 OK u0 698.63 GB SATA 2 - WDC WD7500AADS-00M2 p3 OK u0 698.63 GB SATA 3 - WDC WD7500AADS-00M2 We have recently changed almost all components of server (excluding 3ware controller + disks). And I think problems started since then. Can it be configuration problem or hardware? EDIT: I found something like that in dmesg [166843.625843] irq 16: nobody cared (try booting with the "irqpoll" option) [166843.625846] Pid: 0, comm: swapper Not tainted 3.1.5-gentoo #3 [166843.625847] Call Trace: [166843.625848] <IRQ> [<ffffffff810859d5>] __report_bad_irq+0x35/0xc1 [166843.625856] [<ffffffff81085cec>] note_interrupt+0x165/0x1e1 [166843.625859] [<ffffffff8108445f>] handle_irq_event_percpu+0x16f/0x187 [166843.625861] [<ffffffff810844a9>] handle_irq_event+0x32/0x51 [166843.625863] [<ffffffff8108640b>] handle_fasteoi_irq+0x75/0x99 [166843.625866] [<ffffffff810039d7>] handle_irq+0x83/0x8b [166843.625868] [<ffffffff810036ad>] do_IRQ+0x48/0xa0 [166843.625871] [<ffffffff8155082b>] common_interrupt+0x6b/0x6b [166843.625872] <EOI> [<ffffffff812981e8>] ? acpi_safe_halt+0x22/0x35 [166843.625877] [<ffffffff812981e2>] ? acpi_safe_halt+0x1c/0x35 [166843.625879] [<ffffffff81298216>] acpi_idle_do_entry+0x1b/0x2b [166843.625881] [<ffffffff81298276>] acpi_idle_enter_c1+0x50/0x99 [166843.625884] [<ffffffff813b792a>] cpuidle_idle_call+0xed/0x171 [166843.625886] [<ffffffff81001257>] cpu_idle+0x55/0x81 [166843.625888] [<ffffffff81532a69>] rest_init+0x6d/0x6f [166843.625891] [<ffffffff81aa1aca>] start_kernel+0x329/0x334 [166843.625893] [<ffffffff81aa12a6>] x86_64_start_reservations+0xb6/0xba [166843.625894] [<ffffffff81aa139c>] x86_64_start_kernel+0xf2/0xf9 [166843.625896] handlers: [166843.625898] [<ffffffff812dc8de>] twl_interrupt [166843.625900] Disabling IRQ #16 It's related to problem? EDIT #2: Based on feedback in comments, here is more informations. cat /proc/interrupts 16: 390813 0 0 0 IO-APIC-fasteoi 3w-sas Controller model: [ 1.095350] 3ware Storage Controller device driver for Linux v1.26.02.003. [ 1.095467] 3ware 9000 Storage Controller device driver for Linux v2.26.02.014. [ 1.095641] LSI 3ware SAS/SATA-RAID Controller device driver for Linux v3.26.02.000. [ 1.095787] 3w-sas 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.095881] 3w-sas 0000:01:00.0: setting latency timer to 64 [ 1.910801] 3w-sas: scsi0: Found an LSI 3ware 9750-4i Controller at 0xfe560000, IRQ: 16. [ 2.216537] 3w-sas: scsi0: Firmware FH9X 5.08.00.008, BIOS BE9X 5.07.00.011, Phys: 8. [ 2.216836] scsi 0:0:0:0: Direct-Access LSI 9750-4i DISK 5.08 PQ: 0 ANSI: 5 And motherboard: description: Motherboard product: P8H67-M vendor: ASUSTeK Computer INC.

    Read the article

  • udp through nat

    - by youllknow
    Hi everyone! I've two private networks (each of them behind a typical dsl router). The routers are connected to the WWW. The extern interface of each router have one dynamic IP address. I want to stream data via UDP directly between one client in private network A and one client in private network B. I've already tried a lot of things (see: http://en.wikipedia.org/wiki/UDP_hole_punching, or STUN). But it wasn't possible for me to transfer data between the two clients. It's possible to use a server (located in the WWW, with static IP) to transfer the extern IPs (and extern ports) from the routers between the clients. So imagine client A knows client B's external IP and client B's external port assigned by his router. I simply tried sending UDP packet to the receivers external IP/port combination, but without any result. So does anyone know what do to communicate via UDP throw the two NAT routers? It must be possible??? Or does Skype, for example, not directly communicate between the clients when the call eachother (voice over ip). I am sorry for my bad English! If something is confusing don't mind asking me!!! Thanks for your help in advance. ::::EDIT:::: I can't get pwnat or chownat working. I tried it with my own dsl-gateway - didn't work. Then I set up a complete virtual environment using VMWare. C1 (Client 1, WinXP Prof SP3): 172.16.16.100/24, GW 172.16.16.1 C2 (Client 2, WinXP Prof SP3): 10.0.0.100/24, GW 10.0.0.1 C3 (Client 3, WinXP Prof SP3): 3.0.0.2/24, GW 3.0.0.1 S1 (Ubuntu 10.04 x64 Server): eth0: 172.16.16.1/24, eth1: 1.0.0.2/24 GW 1.0.0.1 S2 (Ubuntu 10.04 x64 Server): eth0: 10.0.0.1/24, eth1: 2.0.0.2/24 GW 2.0.0.1 S3 (Ubuntu 10.04 x64 Server): eth0: 1.0.0.1/24, eth1: 2.0.0.1/24, eth2: 3.0.0.1/24 +--+ +--+ +--+ +--+ +--+ |C1|-----|S1|-----|S3|-----|S2|-----|C2| +--+ +--+ +--+ +--+ +--+ | +--+ |C3| +--+ Server S1 and S2 provide NAT functionality. (they have routing enabled and provide a firewall, which allows trafic from the internal net and provide the nat functionality) Server S3 has routing enabled. The client firewalls are turned off. C1 and C2 are able to ping C3, e.g. visit C3's webserver. They are also able to send UDP Packets to C3 (C3 successful receives them)! C1 and C2 have also webservers running for test reasons. I run ""chownat -s 80 2.0.0.2"" at C1, and ""chownat -c 8000 1.0.0.2"" at C2. Then I tried to access the Webpage from C1 via webbrower localhost at port 8000. It didn't work. Can anybody help me? Any suggestions? If you have any questions to my question, please ask!

    Read the article

  • Where's my memory?! Nginx + PHP-FPM front end webserver slows to a crawl...

    - by incredimike
    I'm not sure if I have a problem with a memory leak (as my hosting company suggests), or if we both need to read http://linuxatemyram.com. Maybe you clever people can help us out? This is a front-end webserver VM running essentially only nginx & php-fpm on RHEL 5.5. This server is powering Magento, a PHP eCommerce thinggy. The server is running in a shared environment, but we're changing that soon. Anyway.. after a reboot the server runs just fine, but within a day it will grind itself into nothingness. Pages will take literally 2 minutes to load, CPU spikes like crazy, etc.. The console is even sluggish when I SSH in. It's like my whole server is being brought to its knees. I've also been monitoring the DB server via top and tcpdumping incoming traffic. The DB stays idle for a good portion of that "slow" load time. When i start seeing queries coming from the front-end server, the page loads soon afterward. Here are some stats after me logging in during a slow-down, after restarting php-fpm: [mike@front01 ~]$ free -m total used free shared buffers cached Mem: 5963 5217 745 0 192 314 -/+ buffers/cache: 4711 1252 Swap: 4047 4 4042 [mike@front01 ~]$ top top - 11:38:55 up 2 days, 1:01, 3 users, load average: 0.06, 0.17, 0.21 Tasks: 131 total, 1 running, 130 sleeping, 0 stopped, 0 zombie Cpu0 : 0.0%us, 0.3%sy, 0.0%ni, 99.3%id, 0.3%wa, 0.0%hi, 0.0%si, 0.0%st Cpu1 : 0.3%us, 0.0%sy, 0.0%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu2 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 6106800k total, 5361288k used, 745512k free, 199960k buffers Swap: 4144728k total, 4976k used, 4139752k free, 328480k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 31806 apache 15 0 601m 120m 37m S 0.0 2.0 0:22.23 php-fpm 31805 apache 15 0 549m 66m 31m S 0.0 1.1 0:14.54 php-fpm 31809 apache 16 0 547m 65m 32m S 0.0 1.1 0:12.84 php-fpm 32285 apache 15 0 546m 63m 33m S 0.0 1.1 0:09.22 php-fpm 32373 apache 15 0 546m 62m 32m S 0.0 1.1 0:09.66 php-fpm 31808 apache 16 0 543m 60m 35m S 0.0 1.0 0:18.93 php-fpm 31807 apache 16 0 533m 49m 30m S 0.0 0.8 0:08.93 php-fpm 32092 apache 15 0 535m 48m 27m S 0.0 0.8 0:06.67 php-fpm 4392 root 18 0 194m 10m 7184 S 0.0 0.2 0:06.96 cvd 4064 root 15 0 154m 8304 4220 S 0.0 0.1 3:55.57 snmpd 4394 root 15 0 119m 5660 2944 S 0.0 0.1 0:02.84 EvMgrC 31804 root 15 0 519m 5180 932 S 0.0 0.1 0:00.46 php-fpm 4138 ntp 15 0 23396 5032 3904 S 0.0 0.1 0:02.38 ntpd 643 nginx 15 0 95276 4408 1524 S 0.0 0.1 0:01.15 nginx 5131 root 16 0 90128 3340 2600 S 0.0 0.1 0:01.41 sshd 28467 root 15 0 90128 3340 2600 S 0.0 0.1 0:00.35 sshd 32602 root 16 0 90128 3332 2600 S 0.0 0.1 0:00.36 sshd 1614 root 16 0 90128 3308 2588 S 0.0 0.1 0:00.02 sshd 2817 root 5 -10 7216 3140 1724 S 0.0 0.1 0:03.80 iscsid 4161 root 15 0 66948 2340 800 S 0.0 0.0 0:10.35 sendmail 1617 nicole 17 0 53876 2000 1516 S 0.0 0.0 0:00.02 sftp-server ... Is there anything else I should be looking at, or any more information that might be useful? I'm just a developer, but the slowdowns on this system worry me and make it hard to do my work.. Help me out, ServerFault!

    Read the article

  • Why does my laptop resume immediately after suspend?

    - by Igor Zinov'yev
    I seem to be having some problem with suspend mode. Every time I try to suspend my laptop, it just locks the screen. Or maybe it successfully suspends just to resume only an instant after. What could cause such a behaviour? I'm running 32-bit Ubuntu 12.04 with the 3.2.0-25 kernel on a HP dv5-1178er Pavilion laptop (Intel Core 2 Duo). Here are the relevant log sections: kern.log: Jun 1 10:42:21 igor-laptop kernel: [ 2225.131171] PM: Syncing filesystems ... done. Jun 1 10:42:21 igor-laptop kernel: [ 2225.141222] PM: Preparing system for mem sleep Jun 1 10:42:21 igor-laptop kernel: [ 2225.141239] Freezing user space processes ... (elapsed 0.01 seconds) done. Jun 1 10:42:21 igor-laptop kernel: [ 2225.156171] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done. Jun 1 10:42:21 igor-laptop kernel: [ 2225.172139] PM: Entering mem sleep Jun 1 10:42:21 igor-laptop kernel: [ 2225.172169] Suspending console(s) (use no_console_suspend to debug) Jun 1 10:42:21 igor-laptop kernel: [ 2225.172895] sd 0:0:0:0: [sda] Synchronizing SCSI cache Jun 1 10:42:21 igor-laptop kernel: [ 2225.181767] sd 0:0:0:0: [sda] Stopping disk Jun 1 10:42:21 igor-laptop kernel: [ 2225.251089] ene_ir 00:0a: wake-up capability enabled by ACPI Jun 1 10:42:21 igor-laptop kernel: [ 2225.251115] i8042 aux 00:09: wake-up capability disabled by ACPI Jun 1 10:42:21 igor-laptop kernel: [ 2225.251133] i8042 kbd 00:08: wake-up capability enabled by ACPI Jun 1 10:42:21 igor-laptop kernel: [ 2225.251286] jmb38x_ms 0000:06:00.3: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.252491] sdhci-pci 0000:06:00.1: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.264130] uhci_hcd 0000:00:1d.2: PCI INT D disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.264142] uhci_hcd 0000:00:1d.1: PCI INT B disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.264325] uhci_hcd 0000:00:1a.1: PCI INT B disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.288059] uhci_hcd 0000:00:1a.0: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.288097] uhci_hcd 0000:00:1d.3: PCI INT C disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.288135] uhci_hcd 0000:00:1d.0: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.316051] ehci_hcd 0000:00:1d.7: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.316068] ehci_hcd 0000:00:1a.7: PCI INT D disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.522872] PM: suspend of drv:sd dev:0:0:0:0 complete after 349.979 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.522901] PM: suspend of drv:scsi dev:target0:0:0 complete after 349.955 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.522927] PM: suspend of drv:scsi dev:host0 complete after 272.260 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.522969] ahci 0000:00:1f.2: BIOS update required for suspend/resume Jun 1 10:42:21 igor-laptop kernel: [ 2225.522976] pci_legacy_suspend(): ahci_pci_device_suspend+0x0/0x80 returns -5 Jun 1 10:42:21 igor-laptop kernel: [ 2225.522981] pm_op(): pci_pm_suspend+0x0/0x110 returns -5 Jun 1 10:42:21 igor-laptop kernel: [ 2225.522984] PM: suspend of drv:ahci dev:0000:00:1f.2 complete after 258.932 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.522987] PM: Device 0000:00:1f.2 failed to suspend async: error -5 Jun 1 10:42:21 igor-laptop kernel: [ 2225.576228] snd_hda_intel 0000:00:1b.0: PCI INT A disabled Jun 1 10:42:21 igor-laptop kernel: [ 2225.576270] ACPI handle has no context! Jun 1 10:42:21 igor-laptop kernel: [ 2225.592136] PM: suspend of drv:snd_hda_intel dev:0000:00:1b.0 complete after 327.889 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.592206] PM: Some devices failed to suspend Jun 1 10:42:21 igor-laptop kernel: [ 2225.592291] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592298] uhci_hcd 0000:00:1a.0: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592325] usb usb3: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592339] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592345] uhci_hcd 0000:00:1a.1: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592371] usb usb4: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592387] ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592395] ehci_hcd 0000:00:1a.7: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592843] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592851] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592854] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592863] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592878] usb usb5: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592892] usb usb6: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592895] uhci_hcd 0000:00:1d.2: PCI INT D -> GSI 16 (level, low) -> IRQ 16 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592903] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592906] uhci_hcd 0000:00:1d.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592915] uhci_hcd 0000:00:1d.3: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592930] usb usb7: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592946] usb usb8: root hub lost power or was reset Jun 1 10:42:21 igor-laptop kernel: [ 2225.592949] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 20 (level, low) -> IRQ 20 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592957] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.592963] pci 0000:00:1e.0: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.597106] sd 0:0:0:0: [sda] Starting disk Jun 1 10:42:21 igor-laptop kernel: [ 2225.608138] snd_hda_intel 0000:00:1b.0: BAR 0: set to [mem 0xdf300000-0xdf303fff 64bit] (PCI address [0xdf300000-0xdf303fff]) Jun 1 10:42:21 igor-laptop kernel: [ 2225.608180] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0xf (was 0x100, writing 0x10b) Jun 1 10:42:21 igor-laptop kernel: [ 2225.608233] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x3 (was 0x0, writing 0x10) Jun 1 10:42:21 igor-laptop kernel: [ 2225.608248] snd_hda_intel 0000:00:1b.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100002) Jun 1 10:42:21 igor-laptop kernel: [ 2225.608299] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 Jun 1 10:42:21 igor-laptop kernel: [ 2225.608313] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.608420] snd_hda_intel 0000:00:1b.0: irq 50 for MSI/MSI-X Jun 1 10:42:21 igor-laptop kernel: [ 2225.612095] firewire_ohci 0000:06:00.0: restoring config space at offset 0x1 (was 0x100000, writing 0x100006) Jun 1 10:42:21 igor-laptop kernel: [ 2225.612181] sdhci-pci 0000:06:00.1: restoring config space at offset 0x1 (was 0x100003, writing 0x100007) Jun 1 10:42:21 igor-laptop kernel: [ 2225.612211] sdhci-pci 0000:06:00.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jun 1 10:42:21 igor-laptop kernel: [ 2225.612225] sdhci-pci 0000:06:00.1: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.612296] jmb38x_ms 0000:06:00.3: restoring config space at offset 0x1 (was 0x100003, writing 0x100007) Jun 1 10:42:21 igor-laptop kernel: [ 2225.612326] jmb38x_ms 0000:06:00.3: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Jun 1 10:42:21 igor-laptop kernel: [ 2225.612332] jmb38x_ms 0000:06:00.3: setting latency timer to 64 Jun 1 10:42:21 igor-laptop kernel: [ 2225.699170] PM: resume of drv:uvcvideo dev:2-4:1.0 complete after 101.965 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.699179] PM: resume of drv:uvcvideo dev:2-4:1.1 complete after 101.932 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.699186] PM: resume of drv: dev:ep_00 complete after 101.917 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.699197] PM: resume of drv: dev:ep_83 complete after 101.972 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716148] PM: resume of drv:hub dev:3-0:1.0 complete after 119.543 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716155] PM: resume of drv: dev:ep_00 complete after 119.544 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716161] PM: resume of drv:hub dev:5-0:1.0 complete after 119.420 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716168] PM: resume of drv: dev:ep_00 complete after 119.381 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716174] PM: resume of drv:hub dev:8-0:1.0 complete after 119.141 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716181] PM: resume of drv: dev:ep_00 complete after 119.104 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716186] PM: resume of drv: dev:ep_81 complete after 119.579 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716191] PM: resume of drv: dev:ep_81 complete after 119.427 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.716197] PM: resume of drv: dev:ep_81 complete after 119.143 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.747148] firewire_core: skipped bus generations, destroying all nodes Jun 1 10:42:21 igor-laptop kernel: [ 2225.776093] PM: resume of drv:hp_accel dev:HPQ0004:00 complete after 167.225 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.777243] i8042 kbd 00:08: wake-up capability disabled by ACPI Jun 1 10:42:21 igor-laptop kernel: [ 2225.777278] ene_ir 00:0a: wake-up capability disabled by ACPI Jun 1 10:42:21 igor-laptop kernel: [ 2225.820100] PM: resume of drv:hub dev:4-0:1.0 complete after 223.436 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820115] PM: resume of drv: dev:ep_00 complete after 223.444 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820123] PM: resume of drv: dev:ep_81 complete after 223.456 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820206] PM: resume of drv:hub dev:7-0:1.0 complete after 223.266 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820221] PM: resume of drv: dev:ep_81 complete after 223.260 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820238] PM: resume of drv: dev:ep_00 complete after 223.255 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820295] PM: resume of drv:hub dev:6-0:1.0 complete after 223.453 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820302] PM: resume of drv: dev:ep_00 complete after 223.415 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.820321] PM: resume of drv: dev:ep_81 complete after 223.457 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2225.932108] usb 4-2: reset full-speed USB device number 2 using uhci_hcd Jun 1 10:42:21 igor-laptop kernel: [ 2226.086714] PM: resume of drv:usbhid dev:4-2:1.0 complete after 489.393 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.086728] PM: resume of drv: dev:ep_81 complete after 489.384 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.086745] PM: resume of drv: dev:ep_00 complete after 489.329 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.086753] PM: resume of drv:usbhid dev:4-2:1.1 complete after 489.384 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.086764] PM: resume of drv: dev:ep_82 complete after 489.373 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.180555] usb 7-2: reset full-speed USB device number 2 using uhci_hcd Jun 1 10:42:21 igor-laptop kernel: [ 2226.244858] firewire_core: rediscovered device fw0 Jun 1 10:42:21 igor-laptop kernel: [ 2226.335066] btusb 7-2:1.0: no reset_resume for driver btusb? Jun 1 10:42:21 igor-laptop kernel: [ 2226.335068] btusb 7-2:1.1: no reset_resume for driver btusb? Jun 1 10:42:21 igor-laptop kernel: [ 2226.432082] usb 6-1: reset full-speed USB device number 2 using uhci_hcd Jun 1 10:42:21 igor-laptop kernel: [ 2226.578280] PM: resume of drv:nvidia dev:0000:01:00.0 complete after 985.301 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584296] PM: resume of drv:usb dev:7-2:1.0 complete after 986.693 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584308] PM: resume of drv: dev:ep_00 complete after 986.452 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584311] PM: resume of drv:usb dev:7-2:1.1 complete after 986.616 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584315] PM: resume of drv:usb dev:7-2:1.3 complete after 986.483 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584320] PM: resume of drv:usb dev:7-2:1.2 complete after 986.556 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584328] PM: resume of drv: dev:ep_03 complete after 986.588 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584331] PM: resume of drv: dev:ep_81 complete after 986.704 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584334] PM: resume of drv: dev:ep_83 complete after 986.617 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584337] PM: resume of drv: dev:ep_82 complete after 986.688 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584340] PM: resume of drv: dev:ep_02 complete after 986.667 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584344] PM: resume of drv: dev:ep_84 complete after 986.558 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.584352] PM: resume of drv: dev:ep_04 complete after 986.542 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.590883] PM: resume of drv: dev:ep_00 complete after 993.327 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.590887] PM: resume of drv:usb dev:6-1:1.0 complete after 993.424 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.590927] PM: resume of drv: dev:ep_82 complete after 993.395 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.590934] PM: resume of drv: dev:ep_81 complete after 993.426 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.590940] PM: resume of drv: dev:ep_01 complete after 993.456 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.592450] PM: resume of drv:sd dev:0:0:0:0 complete after 995.343 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.592461] PM: resume of drv:scsi_disk dev:0:0:0:0 complete after 802.688 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.592472] PM: resume of drv:scsi_device dev:0:0:0:0 complete after 995.324 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.600339] PM: resume of devices complete after 1008.129 msecs Jun 1 10:42:21 igor-laptop kernel: [ 2226.601293] PM: resume devices took 1.008 seconds Jun 1 10:42:21 igor-laptop kernel: [ 2226.601330] PM: Finishing wakeup. Jun 1 10:42:21 igor-laptop kernel: [ 2226.601332] Restarting tasks ... done. Jun 1 10:42:21 igor-laptop kernel: [ 2226.625660] video LNXVIDEO:01: Restoring backlight state Jun 1 10:42:22 igor-laptop kernel: [ 2227.478921] iwlwifi 0000:02:00.0: L1 Disabled; Enabling L0S Jun 1 10:42:22 igor-laptop kernel: [ 2227.481981] iwlwifi 0000:02:00.0: Radio type=0x1-0x2-0x0 Jun 1 10:42:22 igor-laptop kernel: [ 2227.527727] ADDRCONF(NETDEV_UP): wlan0: link is not ready Jun 1 10:42:22 igor-laptop kernel: [ 2227.532468] r8169 0000:03:00.0: eth0: link down Jun 1 10:42:22 igor-laptop kernel: [ 2227.533967] ADDRCONF(NETDEV_UP): eth0: link is not ready pm_suspend.log: Fri Jun 1 10:42:14 MSK 2012: Running hooks for suspend. Running hook /usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend: /usr/lib/pm-utils/sleep.d/000kernel-change suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/00logging suspend suspend: Linux igor-laptop 3.2.0-25-generic #40-Ubuntu SMP Wed May 23 20:33:05 UTC 2012 i686 i686 i386 GNU/Linux Module Size Used by pci_stub 12550 1 vboxpci 22882 0 vboxnetadp 13328 0 vboxnetflt 27211 0 vboxdrv 252189 3 vboxpci,vboxnetadp,vboxnetflt dm_crypt 22528 0 snd_hda_codec_hdmi 31775 1 snd_hda_codec_idt 60251 1 arc4 12473 2 hp_wmi 13652 0 sparse_keymap 13658 1 hp_wmi rfcomm 38139 12 snd_hda_intel 32765 5 snd_hda_codec 109562 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec bnep 17830 2 btusb 17912 2 bluetooth 158438 23 rfcomm,bnep,btusb joydev 17393 0 parport_pc 32114 0 snd_pcm 80845 4 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec ppdev 12849 0 uvcvideo 67203 0 binfmt_misc 17292 1 videodev 86588 1 uvcvideo snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi nvidia 10958194 43 snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event ir_lirc_codec 12739 0 lirc_dev 18700 1 ir_lirc_codec snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq ir_mce_kbd_decoder 12681 0 ir_sony_decoder 12462 0 ir_jvc_decoder 12459 0 ir_rc6_decoder 12459 0 psmouse 87213 0 ir_rc5_decoder 12459 0 serio_raw 13027 0 iwlwifi 287934 0 rc_rc6_mce 12454 0 ir_nec_decoder 12459 0 ene_ir 18019 0 rc_core 21263 10 ir_lirc_codec,ir_mce_kbd_decoder,ir_sony_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_rc5_decoder,rc_rc6_mce,ir_nec_decoder,ene_ir mac80211 436455 1 iwlwifi snd 62064 19 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device cfg80211 178679 2 iwlwifi,mac80211 hp_accel 25728 0 lis3lv02d 19268 1 hp_accel input_polldev 13648 1 lis3lv02d mac_hid 13077 0 wmi 18744 1 hp_wmi jmb38x_ms 17406 0 soundcore 14635 1 snd snd_page_alloc 14115 2 snd_hda_intel,snd_pcm memstick 15857 1 jmb38x_ms firewire_sbp2 18346 0 lp 17455 0 parport 40930 3 parport_pc,ppdev,lp vesafb 13516 1 usbhid 41906 0 hid 77367 1 usbhid firewire_ohci 40180 0 firewire_core 56906 2 firewire_sbp2,firewire_ohci crc_itu_t 12627 1 firewire_core sdhci_pci 18324 0 sdhci 28241 1 sdhci_pci r8169 56321 0 video 19068 0 total used free shared buffers cached Mem: 3095544 2364260 731284 0 159020 1280240 -/+ buffers/cache: 925000 2170544 Swap: 1718916 0 1718916 /usr/lib/pm-utils/sleep.d/00logging suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/00powersave suspend suspend: /usr/lib/pm-utils/sleep.d/00powersave suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend: Welcome to PulseAudio! Use "help" for usage information. >>> >>> Welcome to PulseAudio! Use "help" for usage information. >>> >>> Welcome to PulseAudio! Use "help" for usage information. >>> >>> /usr/lib/pm-utils/sleep.d/01PulseAudio suspend suspend: success. Running hook /etc/pm/sleep.d/10_grub-common suspend suspend: /etc/pm/sleep.d/10_grub-common suspend suspend: success. Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend: /etc/pm/sleep.d/10_unattended-upgrades-hibernate suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend: Having NetworkManager put all interaces to sleep...Failed. /usr/lib/pm-utils/sleep.d/55NetworkManager suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend: Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory /usr/lib/pm-utils/sleep.d/60_wpa_supplicant suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/75modules suspend suspend: /usr/lib/pm-utils/sleep.d/75modules suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/90clock suspend suspend: /usr/lib/pm-utils/sleep.d/90clock suspend suspend: not applicable. Running hook /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: /usr/lib/pm-utils/sleep.d/94cpufreq suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/95anacron suspend suspend: stop: Unknown instance: /usr/lib/pm-utils/sleep.d/95anacron suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend: /usr/lib/pm-utils/sleep.d/95hdparm-apm suspend suspend: not applicable. Running hook /usr/lib/pm-utils/sleep.d/95led suspend suspend: /usr/lib/pm-utils/sleep.d/95led suspend suspend: not applicable. Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: nVidia binary video drive detected, not using quirks. /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler suspend suspend: success. Running hook /usr/lib/pm-utils/sleep.d/99video suspend suspend: kernel.acpi_video_flags = 0 /usr/lib/pm-utils/sleep.d/99video suspend suspend: success. Running hook /etc/pm/sleep.d/novatel_3g_suspend suspend suspend: /etc/pm/sleep.d/novatel_3g_suspend suspend suspend: success. Fri Jun 1 10:42:19 MSK 2012: performing suspend Fri Jun 1 10:42:21 MSK 2012: Awake. Fri Jun 1 10:42:21 MSK 2012: Running hooks for resume Running hook /etc/pm/sleep.d/novatel_3g_suspend resume suspend: /etc/pm/sleep.d/novatel_3g_suspend resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/99video resume suspend: /usr/lib/pm-utils/sleep.d/99video resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: /usr/lib/pm-utils/sleep.d/98video-quirk-db-handler resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/95led resume suspend: /usr/lib/pm-utils/sleep.d/95led resume suspend: not applicable. Running hook /usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend: /dev/sda: setting Advanced Power Management level to 0xfe (254) APM_level = 254 /dev/sda: setting Advanced Power Management level to 0xfe (254) APM_level = 254 /usr/lib/pm-utils/sleep.d/95hdparm-apm resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/95anacron resume suspend: /usr/lib/pm-utils/sleep.d/95anacron resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: /usr/lib/pm-utils/sleep.d/94cpufreq resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/90clock resume suspend: /usr/lib/pm-utils/sleep.d/90clock resume suspend: not applicable. Running hook /usr/lib/pm-utils/sleep.d/75modules resume suspend: Reloaded unloaded modules. /usr/lib/pm-utils/sleep.d/75modules resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend: Failed to connect to wpa_supplicant - wpa_ctrl_open: No such file or directory /usr/lib/pm-utils/sleep.d/60_wpa_supplicant resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend: Having NetworkManager wake interfaces back up...Failed. /usr/lib/pm-utils/sleep.d/55NetworkManager resume suspend: success. Running hook /etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend: /etc/pm/sleep.d/10_unattended-upgrades-hibernate resume suspend: success. Running hook /etc/pm/sleep.d/10_grub-common resume suspend: /etc/pm/sleep.d/10_grub-common resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend: Welcome to PulseAudio! Use "help" for usage information. >>> >>> Welcome to PulseAudio! Use "help" for usage information. >>> >>> Welcome to PulseAudio! Use "help" for usage information. >>> >>> /usr/lib/pm-utils/sleep.d/01PulseAudio resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/00powersave resume suspend: /usr/lib/pm-utils/sleep.d/00powersave resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/00logging resume suspend: /usr/lib/pm-utils/sleep.d/00logging resume suspend: success. Running hook /usr/lib/pm-utils/sleep.d/000kernel-change resume suspend: /usr/lib/pm-utils/sleep.d/000kernel-change resume suspend: success. Fri Jun 1 10:42:22 MSK 2012: Finished.

    Read the article

  • Mac OS X Server Configure DHCP Options 66 and 67

    - by Paul Adams
    I need to configure Mountain Lion (10.8.2) OS X Server BOOTP to provide DHCP options 66 and 67 to provide PXE booting for PCs on my network. I have tried following the bootpd MAN pages, but they are not specific enough. I have also read conflicting information on the net, but nothing definitive for Mountain Lion DHCP. From bootpd man page: bootpd has a built-in type conversion table for many more options, mostly those specified in RFC 2132, and will try to convert from whatever type the option appears in the property list to the binary, packet format. For example, if bootpd knows that the type of the option is an IP address or list of IP addresses, it converts from the string form of the IP address to the binary, network byte order numeric value. If the type of the option is a numeric value, it converts from string, integer, or boolean, to the proper sized, network byte-order numeric value. Regardless of whether bootpd knows the type of the option or not, you can always specify the DHCP option using the data property list type <key>dhcp_option_128</key> <data> AAqV1Tzo </data> My TFTP server is 172.16.152.20 and the bootfile is pxelinux.0 I have edited /etc/bootpd.plist and added the following to the subnet dict: <key>dhcp_option_66</key> <data> LW4gLWUgrBCYFAo= </data> <key>dhcp_option_67</key> <data> LW4gLWUgcHhlbGludXguMAo= </data> According to the man page, the data elements are supposed to be Base64 encoded, but no matter what I try, I cannot get PXE clients to boot. I have tried encoding 172.16.152.20 using various methods: echo "172.16.152.20" | openssl enc -base64 returns MTcyLjE2LjE1Mi4yMAo= DHCP Option Code Utility (http://mac.softpedia.com/get/Internet-Utilities/DHCP-Option-Code-Utility.shtml) generating a string from 172.16.152.20 yields: LW4gLWUgMTcyLjE2LjE1Mi4yMAo= (used in the above example) DHCP Option Code Utility generating an IP Addresss from 172.16.152.20 yields: LW4gLWUgrBCYFAo= Encoding pxelinux.0 with the above methods likewise yields different encodings. I have tried using all three methods of encoding the data elements, but nothing seems to work i.e. my PXE boot clients do not get directed to my TFTP server. Can anyone help? Regards, Paul Adams.

    Read the article

  • Resuming blogging activities and a maths question

    - by ali.mukadam
    Resuming my blogging activities and unlike Dumbledore, I do not have a pensieve to review my thoughts and put them in order. On the other hand, thinking of maths problems somehow seem to make them clearer. So before I start writing long-winding blog posts, here's one I was given 16 years ago: The length of a rectangle is 6 cm smaller than its width. If the area of the rectangle is 16, what is its perimeter? Hint: Solvable in 5 lines or less. Cheers, Ali

    Read the article

  • RHEL 5.5 Yum Update Fails Dependency Error

    - by user65788
    I have 30 different RHEL 5.5 machines that will not update some 33 packages via Yum. Does anyone know why these packages will not install and how to correct this? Yum clean all does not fix the issue, however skip broken will allow other updates to install but I am really after a way to clear this up for good. They are stock boxes with RHEL subscription and not using any yum repositories other than Red Hat's own official repositories. They have not been updated for over a year! yum update Loaded plugins: rhnplugin, security rhel-i386-client-5 | 1.4 kB 00:00 rhel-i386-client-5/primary | 2.8 MB 00:09 rhel-i386-client-5 6607/6607 Skipping security plugin, no data Setting up Update Process Resolving Dependencies Skipping security plugin, no data --> Running transaction check ---> Package autofs.i386 1:5.0.1-0.rc2.143.el5_5.6 set to be updated ---> Package cpp.i386 0:4.1.2-48.el5 set to be updated --> Processing Dependency: curl = 7.15.5-2.1.el5_3.5 for package: curl-devel ---> Package curl.i386 0:7.15.5-9.el5 set to be updated --> Processing Dependency: cyrus-sasl-lib = 2.1.22-5.el5 for package: cyrus-sasl-devel ---> Package cyrus-sasl-lib.i386 0:2.1.22-5.el5_4.3 set to be updated ---> Package cyrus-sasl-md5.i386 0:2.1.22-5.el5_4.3 set to be updated ---> Package cyrus-sasl-plain.i386 0:2.1.22-5.el5_4.3 set to be updated --> Processing Dependency: db4 = 4.3.29-10.el5 for package: db4-devel ---> Package db4.i386 0:4.3.29-10.el5_5.2 set to be updated --> Processing Dependency: dbus = 1.1.2-12.el5 for package: dbus-devel ---> Package dbus.i386 0:1.1.2-14.el5 set to be updated ---> Package dbus-libs.i386 0:1.1.2-14.el5 set to be updated ---> Package dbus-x11.i386 0:1.1.2-14.el5 set to be updated ---> Package e2fsprogs.i386 0:1.39-23.el5_5.1 set to be updated --> Processing Dependency: e2fsprogs-libs = 1.39-23.el5 for package: e2fsprogs-devel ---> Package e2fsprogs-libs.i386 0:1.39-23.el5_5.1 set to be updated ---> Package esc.i386 0:1.1.0-12.el5 set to be updated --> Processing Dependency: expat = 1.95.8-8.2.1 for package: expat-devel ---> Package expat.i386 0:1.95.8-8.3.el5_5.3 set to be updated ---> Package firefox.i386 0:3.6.13-2.el5 set to be updated --> Processing Dependency: freetype = 2.2.1-21.el5_3 for package: freetype-devel ---> Package freetype.i386 0:2.2.1-28.el5_5.1 set to be updated --> Processing Dependency: gcc = 4.1.2-46.el5_4.1 for package: gcc-c++ --> Processing Dependency: gcc = 4.1.2-46.el5_4.1 for package: gcc-gfortran ---> Package gcc.i386 0:4.1.2-48.el5 set to be updated --> Processing Dependency: gd = 2.0.33-9.4.el5_1.1 for package: gd-devel ---> Package gd.i386 0:2.0.33-9.4.el5_4.2 set to be updated --> Processing Dependency: gnome-vfs2 = 2.16.2-4.el5 for package: gnome-vfs2-devel ---> Package gnome-vfs2.i386 0:2.16.2-6.el5_5.1 set to be updated ---> Package gnome-vfs2-smb.i386 0:2.16.2-6.el5_5.1 set to be updated --> Processing Dependency: gnutls = 1.4.1-3.el5_3.5 for package: gnutls-devel ---> Package gnutls.i386 0:1.4.1-3.el5_4.8 set to be updated --> Processing Dependency: gtk2 = 2.10.4-20.el5 for package: gtk2-devel ---> Package gtk2.i386 0:2.10.4-21.el5_5.6 set to be updated --> Processing Dependency: hal = 0.5.8.1-52.el5 for package: hal-devel ---> Package hal.i386 0:0.5.8.1-59.el5 set to be updated --> Processing Dependency: krb5-libs = 1.6.1-36.el5 for package: krb5-devel ---> Package krb5-libs.i386 0:1.6.1-36.el5_5.6 set to be updated ---> Package krb5-workstation.i386 0:1.6.1-36.el5_5.6 set to be updated --> Processing Dependency: libXi = 1.0.1-3.1 for package: libXi-devel ---> Package libXi.i386 0:1.0.1-4.el5_4 set to be updated --> Processing Dependency: libXrandr = 1.1.1-3.1 for package: libXrandr-devel ---> Package libXrandr.i386 0:1.1.1-3.3 set to be updated --> Processing Dependency: libXt = 1.0.2-3.1.fc6 for package: libXt-devel ---> Package libXt.i386 0:1.0.2-3.2.el5 set to be updated --> Processing Dependency: libgfortran = 4.1.2-46.el5_4.1 for package: gcc-gfortran ---> Package libgfortran.i386 0:4.1.2-48.el5 set to be updated --> Processing Dependency: libsepol = 1.15.2-2.el5 for package: libsepol-devel ---> Package libsepol.i386 0:1.15.2-3.el5 set to be updated --> Processing Dependency: libstdc++ = 4.1.2-46.el5_4.1 for package: gcc-c++ --> Processing Dependency: libstdc++ = 4.1.2-46.el5_4.1 for package: libstdc++-devel ---> Package libstdc++.i386 0:4.1.2-48.el5 set to be updated --> Processing Dependency: mesa-libGL = 6.5.1-7.7.el5 for package: mesa-libGL-devel ---> Package mesa-libGL.i386 0:6.5.1-7.8.el5 set to be updated --> Processing Dependency: mesa-libGLU = 6.5.1-7.7.el5 for package: mesa-libGLU-devel ---> Package mesa-libGLU.i386 0:6.5.1-7.8.el5 set to be updated --> Processing Dependency: newt = 0.52.2-12.el5_4.1 for package: newt-devel ---> Package newt.i386 0:0.52.2-15.el5 set to be updated --> Processing Dependency: nspr = 4.7.6-1.el5_4 for package: nspr-devel ---> Package nspr.i386 0:4.8.6-1.el5 set to be updated --> Processing Dependency: nss = 3.12.3.99.3-1.el5_3.2 for package: nss-devel ---> Package nss.i386 0:3.12.8-1.el5 set to be updated ---> Package nss-tools.i386 0:3.12.8-1.el5 set to be updated --> Processing Dependency: openldap = 2.3.43-3.el5 for package: openldap-devel ---> Package openldap.i386 0:2.3.43-12.el5_5.3 set to be updated ---> Package openldap-clients.i386 0:2.3.43-12.el5_5.3 set to be updated --> Processing Dependency: openssl = 0.9.8e-12.el5 for package: openssl-devel ---> Package openssl.i686 0:0.9.8e-12.el5_5.7 set to be updated --> Processing Dependency: pam = 0.99.6.2-6.el5 for package: pam-devel ---> Package pam.i386 0:0.99.6.2-6.el5_5.2 set to be updated --> Processing Dependency: popt = 1.10.2.3-18.el5 for package: rpm-devel --> Processing Dependency: popt = 1.10.2.3-18.el5 for package: rpm-build ---> Package popt.i386 0:1.10.2.3-20.el5_5.1 set to be updated --> Processing Dependency: python = 2.4.3-27.el5 for package: python-devel ---> Package python.i386 0:2.4.3-27.el5_5.3 set to be updated --> Processing Dependency: rpm = 4.4.2.3-18.el5 for package: rpm-devel --> Processing Dependency: rpm = 4.4.2.3-18.el5 for package: rpm-build ---> Package rpm.i386 0:4.4.2.3-20.el5_5.1 set to be updated --> Processing Dependency: rpm-libs = 4.4.2.3-18.el5 for package: rpm-devel --> Processing Dependency: rpm-libs = 4.4.2.3-18.el5 for package: rpm-build ---> Package rpm-libs.i386 0:4.4.2.3-20.el5_5.1 set to be updated ---> Package rpm-python.i386 0:4.4.2.3-20.el5_5.1 set to be updated ---> Package xulrunner.i386 0:1.9.2.13-3.el5 set to be updated ---> Package xulrunner-devel.i386 0:1.9.2.7-2.el5 set to be updated --> Processing Dependency: xulrunner = 1.9.2.7-2.el5 for package: xulrunner-devel --> Processing Dependency: nss-devel >= 3.12.6 for package: xulrunner-devel --> Processing Dependency: nspr-devel >= 4.8 for package: xulrunner-devel --> Processing Dependency: libnotify-devel for package: xulrunner-devel ---> Package yelp.i386 0:2.16.0-26.el5 set to be updated rhel-i386-client-5/filelists | 16 MB 00:45 --> Finished Dependency Resolution xulrunner-devel-1.9.2.7-2.el5.i386 from rhel-i386-client-5 has depsolving problems --> Missing Dependency: libnotify-devel is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) mesa-libGLU-devel-6.5.1-7.7.el5.i386 from installed has depsolving problems --> Missing Dependency: mesa-libGLU = 6.5.1-7.7.el5 is needed by package mesa-libGLU-devel-6.5.1-7.7.el5.i386 (installed) python-devel-2.4.3-27.el5.i386 from installed has depsolving problems --> Missing Dependency: python = 2.4.3-27.el5 is needed by package python-devel-2.4.3-27.el5.i386 (installed) nss-devel-3.12.3.99.3-1.el5_3.2.i386 from installed has depsolving problems --> Missing Dependency: nss = 3.12.3.99.3-1.el5_3.2 is needed by package nss-devel-3.12.3.99.3-1.el5_3.2.i386 (installed) libstdc++-devel-4.1.2-46.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: libstdc++ = 4.1.2-46.el5_4.1 is needed by package libstdc++-devel-4.1.2-46.el5_4.1.i386 (installed) xulrunner-devel-1.9.2.7-2.el5.i386 from rhel-i386-client-5 has depsolving problems --> Missing Dependency: nspr-devel >= 4.8 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) gcc-c++-4.1.2-46.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: libstdc++ = 4.1.2-46.el5_4.1 is needed by package gcc-c++-4.1.2-46.el5_4.1.i386 (installed) rpm-devel-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: rpm-libs = 4.4.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) xulrunner-devel-1.9.2.7-2.el5.i386 from rhel-i386-client-5 has depsolving problems --> Missing Dependency: xulrunner = 1.9.2.7-2.el5 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) nspr-devel-4.7.6-1.el5_4.i386 from installed has depsolving problems --> Missing Dependency: nspr = 4.7.6-1.el5_4 is needed by package nspr-devel-4.7.6-1.el5_4.i386 (installed) libXrandr-devel-1.1.1-3.1.i386 from installed has depsolving problems --> Missing Dependency: libXrandr = 1.1.1-3.1 is needed by package libXrandr-devel-1.1.1-3.1.i386 (installed) libsepol-devel-1.15.2-2.el5.i386 from installed has depsolving problems --> Missing Dependency: libsepol = 1.15.2-2.el5 is needed by package libsepol-devel-1.15.2-2.el5.i386 (installed) libXt-devel-1.0.2-3.1.fc6.i386 from installed has depsolving problems --> Missing Dependency: libXt = 1.0.2-3.1.fc6 is needed by package libXt-devel-1.0.2-3.1.fc6.i386 (installed) mesa-libGL-devel-6.5.1-7.7.el5.i386 from installed has depsolving problems --> Missing Dependency: mesa-libGL = 6.5.1-7.7.el5 is needed by package mesa-libGL-devel-6.5.1-7.7.el5.i386 (installed) openldap-devel-2.3.43-3.el5.i386 from installed has depsolving problems --> Missing Dependency: openldap = 2.3.43-3.el5 is needed by package openldap-devel-2.3.43-3.el5.i386 (installed) openssl-devel-0.9.8e-12.el5.i386 from installed has depsolving problems --> Missing Dependency: openssl = 0.9.8e-12.el5 is needed by package openssl-devel-0.9.8e-12.el5.i386 (installed) dbus-devel-1.1.2-12.el5.i386 from installed has depsolving problems --> Missing Dependency: dbus = 1.1.2-12.el5 is needed by package dbus-devel-1.1.2-12.el5.i386 (installed) newt-devel-0.52.2-12.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: newt = 0.52.2-12.el5_4.1 is needed by package newt-devel-0.52.2-12.el5_4.1.i386 (installed) gnome-vfs2-devel-2.16.2-4.el5.i386 from installed has depsolving problems --> Missing Dependency: gnome-vfs2 = 2.16.2-4.el5 is needed by package gnome-vfs2-devel-2.16.2-4.el5.i386 (installed) gnutls-devel-1.4.1-3.el5_3.5.i386 from installed has depsolving problems --> Missing Dependency: gnutls = 1.4.1-3.el5_3.5 is needed by package gnutls-devel-1.4.1-3.el5_3.5.i386 (installed) rpm-build-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: rpm-libs = 4.4.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) gd-devel-2.0.33-9.4.el5_1.1.i386 from installed has depsolving problems --> Missing Dependency: gd = 2.0.33-9.4.el5_1.1 is needed by package gd-devel-2.0.33-9.4.el5_1.1.i386 (installed) e2fsprogs-devel-1.39-23.el5.i386 from installed has depsolving problems --> Missing Dependency: e2fsprogs-libs = 1.39-23.el5 is needed by package e2fsprogs-devel-1.39-23.el5.i386 (installed) xulrunner-devel-1.9.2.7-2.el5.i386 from rhel-i386-client-5 has depsolving problems --> Missing Dependency: nss-devel >= 3.12.6 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) krb5-devel-1.6.1-36.el5.i386 from installed has depsolving problems --> Missing Dependency: krb5-libs = 1.6.1-36.el5 is needed by package krb5-devel-1.6.1-36.el5.i386 (installed) gcc-gfortran-4.1.2-46.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: libgfortran = 4.1.2-46.el5_4.1 is needed by package gcc-gfortran-4.1.2-46.el5_4.1.i386 (installed) curl-devel-7.15.5-2.1.el5_3.5.i386 from installed has depsolving problems --> Missing Dependency: curl = 7.15.5-2.1.el5_3.5 is needed by package curl-devel-7.15.5-2.1.el5_3.5.i386 (installed) pam-devel-0.99.6.2-6.el5.i386 from installed has depsolving problems --> Missing Dependency: pam = 0.99.6.2-6.el5 is needed by package pam-devel-0.99.6.2-6.el5.i386 (installed) rpm-build-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: rpm = 4.4.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) expat-devel-1.95.8-8.2.1.i386 from installed has depsolving problems --> Missing Dependency: expat = 1.95.8-8.2.1 is needed by package expat-devel-1.95.8-8.2.1.i386 (installed) gcc-c++-4.1.2-46.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: gcc = 4.1.2-46.el5_4.1 is needed by package gcc-c++-4.1.2-46.el5_4.1.i386 (installed) gtk2-devel-2.10.4-20.el5.i386 from installed has depsolving problems --> Missing Dependency: gtk2 = 2.10.4-20.el5 is needed by package gtk2-devel-2.10.4-20.el5.i386 (installed) gcc-gfortran-4.1.2-46.el5_4.1.i386 from installed has depsolving problems --> Missing Dependency: gcc = 4.1.2-46.el5_4.1 is needed by package gcc-gfortran-4.1.2-46.el5_4.1.i386 (installed) cyrus-sasl-devel-2.1.22-5.el5.i386 from installed has depsolving problems --> Missing Dependency: cyrus-sasl-lib = 2.1.22-5.el5 is needed by package cyrus-sasl-devel-2.1.22-5.el5.i386 (installed) rpm-devel-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: popt = 1.10.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) db4-devel-4.3.29-10.el5.i386 from installed has depsolving problems --> Missing Dependency: db4 = 4.3.29-10.el5 is needed by package db4-devel-4.3.29-10.el5.i386 (installed) rpm-build-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: popt = 1.10.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) rpm-devel-4.4.2.3-18.el5.i386 from installed has depsolving problems --> Missing Dependency: rpm = 4.4.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) libXi-devel-1.0.1-3.1.i386 from installed has depsolving problems --> Missing Dependency: libXi = 1.0.1-3.1 is needed by package libXi-devel-1.0.1-3.1.i386 (installed) hal-devel-0.5.8.1-52.el5.i386 from installed has depsolving problems --> Missing Dependency: hal = 0.5.8.1-52.el5 is needed by package hal-devel-0.5.8.1-52.el5.i386 (installed) freetype-devel-2.2.1-21.el5_3.i386 from installed has depsolving problems --> Missing Dependency: freetype = 2.2.1-21.el5_3 is needed by package freetype-devel-2.2.1-21.el5_3.i386 (installed) Error: Missing Dependency: libgfortran = 4.1.2-46.el5_4.1 is needed by package gcc-gfortran-4.1.2-46.el5_4.1.i386 (installed) Error: Missing Dependency: libsepol = 1.15.2-2.el5 is needed by package libsepol-devel-1.15.2-2.el5.i386 (installed) Error: Missing Dependency: libstdc++ = 4.1.2-46.el5_4.1 is needed by package gcc-c++-4.1.2-46.el5_4.1.i386 (installed) Error: Missing Dependency: mesa-libGL = 6.5.1-7.7.el5 is needed by package mesa-libGL-devel-6.5.1-7.7.el5.i386 (installed) Error: Missing Dependency: mesa-libGLU = 6.5.1-7.7.el5 is needed by package mesa-libGLU-devel-6.5.1-7.7.el5.i386 (installed) Error: Missing Dependency: freetype = 2.2.1-21.el5_3 is needed by package freetype-devel-2.2.1-21.el5_3.i386 (installed) Error: Missing Dependency: hal = 0.5.8.1-52.el5 is needed by package hal-devel-0.5.8.1-52.el5.i386 (installed) Error: Missing Dependency: libXt = 1.0.2-3.1.fc6 is needed by package libXt-devel-1.0.2-3.1.fc6.i386 (installed) Error: Missing Dependency: openldap = 2.3.43-3.el5 is needed by package openldap-devel-2.3.43-3.el5.i386 (installed) Error: Missing Dependency: libstdc++ = 4.1.2-46.el5_4.1 is needed by package libstdc++-devel-4.1.2-46.el5_4.1.i386 (installed) Error: Missing Dependency: nss-devel >= 3.12.6 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) Error: Missing Dependency: newt = 0.52.2-12.el5_4.1 is needed by package newt-devel-0.52.2-12.el5_4.1.i386 (installed) Error: Missing Dependency: gnutls = 1.4.1-3.el5_3.5 is needed by package gnutls-devel-1.4.1-3.el5_3.5.i386 (installed) Error: Missing Dependency: gnome-vfs2 = 2.16.2-4.el5 is needed by package gnome-vfs2-devel-2.16.2-4.el5.i386 (installed) Error: Missing Dependency: libXrandr = 1.1.1-3.1 is needed by package libXrandr-devel-1.1.1-3.1.i386 (installed) Error: Missing Dependency: python = 2.4.3-27.el5 is needed by package python-devel-2.4.3-27.el5.i386 (installed) Error: Missing Dependency: gcc = 4.1.2-46.el5_4.1 is needed by package gcc-c++-4.1.2-46.el5_4.1.i386 (installed) Error: Missing Dependency: libnotify-devel is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) Error: Missing Dependency: popt = 1.10.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: openssl = 0.9.8e-12.el5 is needed by package openssl-devel-0.9.8e-12.el5.i386 (installed) Error: Missing Dependency: curl = 7.15.5-2.1.el5_3.5 is needed by package curl-devel-7.15.5-2.1.el5_3.5.i386 (installed) Error: Missing Dependency: xulrunner = 1.9.2.7-2.el5 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) Error: Missing Dependency: nspr = 4.7.6-1.el5_4 is needed by package nspr-devel-4.7.6-1.el5_4.i386 (installed) Error: Missing Dependency: nss = 3.12.3.99.3-1.el5_3.2 is needed by package nss-devel-3.12.3.99.3-1.el5_3.2.i386 (installed) Error: Missing Dependency: popt = 1.10.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: libXi = 1.0.1-3.1 is needed by package libXi-devel-1.0.1-3.1.i386 (installed) Error: Missing Dependency: nspr-devel >= 4.8 is needed by package xulrunner-devel-1.9.2.7-2.el5.i386 (rhel-i386-client-5) Error: Missing Dependency: pam = 0.99.6.2-6.el5 is needed by package pam-devel-0.99.6.2-6.el5.i386 (installed) Error: Missing Dependency: rpm = 4.4.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: cyrus-sasl-lib = 2.1.22-5.el5 is needed by package cyrus-sasl-devel-2.1.22-5.el5.i386 (installed) Error: Missing Dependency: gtk2 = 2.10.4-20.el5 is needed by package gtk2-devel-2.10.4-20.el5.i386 (installed) Error: Missing Dependency: dbus = 1.1.2-12.el5 is needed by package dbus-devel-1.1.2-12.el5.i386 (installed) Error: Missing Dependency: db4 = 4.3.29-10.el5 is needed by package db4-devel-4.3.29-10.el5.i386 (installed) Error: Missing Dependency: rpm-libs = 4.4.2.3-18.el5 is needed by package rpm-build-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: gcc = 4.1.2-46.el5_4.1 is needed by package gcc-gfortran-4.1.2-46.el5_4.1.i386 (installed) Error: Missing Dependency: expat = 1.95.8-8.2.1 is needed by package expat-devel-1.95.8-8.2.1.i386 (installed) Error: Missing Dependency: gd = 2.0.33-9.4.el5_1.1 is needed by package gd-devel-2.0.33-9.4.el5_1.1.i386 (installed) Error: Missing Dependency: krb5-libs = 1.6.1-36.el5 is needed by package krb5-devel-1.6.1-36.el5.i386 (installed) Error: Missing Dependency: rpm = 4.4.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: rpm-libs = 4.4.2.3-18.el5 is needed by package rpm-devel-4.4.2.3-18.el5.i386 (installed) Error: Missing Dependency: e2fsprogs-libs = 1.39-23.el5 is needed by package e2fsprogs-devel-1.39-23.el5.i386 (installed) You could try using --skip-broken to work around the problem You could try running: package-cleanup --problems package-cleanup --dupes rpm -Va --nofiles --nodigest The repolist is yum repolist all Loaded plugins: rhnplugin, security repo id repo name status rhel-debuginfo Red Hat Enterprise Linux 5Client - i386 - Deb disabled rhel-debuginfo-beta Red Hat Enterprise Linux 5Client Beta - i386 disabled rhel-i386-client-5 Red Hat Enterprise Linux Desktop (v. 5 for 32 enabled: 6,607 repolist: 6,607

    Read the article

  • should i bother to block these- rather lame attempt at hacking my server

    - by The Journeyman geek
    I'm running a LAMP stack, with no phpmyadmin (yes) installed. While poking through my apache server longs i noticed things like. 74.208.75.29 - - [16/Mar/2010:02:53:45 +0800] "POST http://74.208.75.29:6667/ HTTP/1.0" 404 481 "-" "-" 74.208.75.29 - - [16/Mar/2010:02:53:45 +0800] "CONNECT 74.208.75.29:6667 HTTP/1.0" 405 547 "-" "-" 66.184.178.58 - - [16/Mar/2010:13:27:59 +0800] "GET / HTTP/1.1" 200 1170 "-" "Mozilla/4.0 (compatible; MSIE 5.5; Windows 98)" 200.78.247.148 - - [16/Mar/2010:15:26:05 +0800] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 506 "-" "-" 206.47.160.224 - - [16/Mar/2010:17:27:57 +0800] "GET / HTTP/1.1" 200 1170 "-" "Mozilla/4.0 (compatible; MSIE 5.5; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:02 +0800] "GET //phpmyadmin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 480 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:03 +0800] "GET //pma/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 476 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:04 +0800] "GET //admin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 478 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:05 +0800] "GET //dbadmin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 479 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:05 +0800] "GET //mysql/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 479 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:06 +0800] "GET //php-my-admin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 482 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" What exactly is happening? is it a really lame attempt at hacking in? Should i bother blocking the ip addresses these are from, or just leave it?

    Read the article

  • 15 Kasim 2012 Oracle Day

    - by TUFEKCIOGLU,FATIH
       15.Kasim'da Harbiye Istanbul Kongre Merkezi'nde düzenlenecek Oracle Day'e ait etkinlik bilgileri : Oracle Day etkinlik bilgileri için tiklayiniz    En Son Teknolojiden Faydalanin: Inovasyona ve Rekabete Zaman Birakin 15 Kasim 2012 Bulut Bilisim, Mobilite, Sosyal Medya ve Büyük Veri, bildigimiz dünyayi yeniden tanimliyor. Bu teknolojileri kurumuna ilk getirenlerden biri olun; daha hizli yeni ürün ve hizmet gelistirme, müsteri deneyimini iyilestirme ve yeni inovatif is modellerini hayata geçirme firsati yakalayarak rekabetteki konumunuzu güçlendirin. Oracle ve is ortaklari bu noktada size, teknolojik yenilikleri kurumunuza uyarlamanizda yardim ederken, sizin de piyasadaki degisimlerden rakiplerinizden önce avantaj elde etmenizi saglar. Oracle'in, birlikte çalismak için tasarlanmis olan yazilim ve donanimlarda en yeni teknolojileri kullanarak, bilgi teknolojilerini nasil sadelestirdigini ögrenmek için Oracle Day'de bize katilin. Oracle Day'de: Oracle'in Bulut Bilisim, Büyük Veri, Sosyal Medya, is uygulamalari çözümleri hakkinda bilgi edinme, Basarili is dönüsümleri hakkinda örnek basari hikayelerini dinleme, Sizinle ayni zorluklari tecrübe eden sektör çalisanlariyla biraraya gelme, Oracle uzmanlari ve is ortaklari ile tanisma ve yeni ürün tanitimlarini izleme, Oracle OpenWorld'den en yeni ürün bilgilerini edinme firsatini kaçirmayin... Saygilarimizla, Oracle Türkiye Hemen Kaydolun! Platin Sponsor Istanbul Kongre Merkezi Taskisla Caddesi Harbiye 34367 Istanbul / Türkiye 15 Kasim 2012, Persembe 08:30 - 18:30 LCV: [email protected] oracle.com/oracleday Bizi takip edin: #oracleday   Oracle Is Ortagi Müsteri Basari Hikayesi TROUG Sunum Ingilizce'dir  Günün Ajandasi 08:45-09:30 Kayit 09:30-10:00 Hos Geldiniz Filiz Dogan, Genel Müdür, Oracle Türkiye 10:00-10:30 Navigating Complexity by Simplifying I.T. Andrew Mendelsohn, Kidemli Baskan Yardimcisi, Oracle Veritabani Sunucu Teknolojileri, Oracle           10:30-11:00 Dönüsümsel Bulut Yolculugu Ilker Kuruöz, CIO, Turkcell 11:00-11:20 Yeni Dönemde Veri Merkezlerinin Olmazsa Olmazlari Yalim Eristiren, Genel Müdür Yardimcisi, Intel 11:20-11:30 Slimfit Feyza Narli, Is Çözümleri Direktörü, Innova 11:30-12:00 Java ile Inovasyon Cuma Yigit, Teknik Mimar, Etiya Yusuf Tok, Java Grup Yöneticisi, OBSS Ersun Engel, Satis Müdürü, Oracle 12:00-12:10  Kahve Molasi       1. SALON 2. SALON 3. SALON 4. SALON 5. SALON 6. SALON 7. SALON 8. SALON 9. SALON 10. SALON   Müsteri Deneyimi: Çalisaninizi Yetkinlestirin. Markanizi Güçlendirin. Is Süreçlerinde Degisim Daha Fazla Veri, Daha Hizli Sonuç: Isinizi Analitik Çözümlerle Güçlendirin Peki Ama Nasil? Bulut Uygulayicilari için Çözüm Haritasi Is Uygulamalarinizda Inovasyonun Gücünü Kullanin Yeni Nesil Veri Merkezi ile BT'nin Gücünü Ortaya Çikartin Oracle & Is Ortaklari Çözümleri - Basari Hikayeleri I Oracle & Is Ortaklari Çözümleri - Basari Hikayeleri II Oracle Finansal Hizmetler - Core Banking and Analytical Solutions Oracle User Group (TROUG) 12:10-12:40 Müsteri Deneyimi: Çalisaninizi Yetkinlestirin. Markanizi Güçlendirin. Tekfen Ceyhan Çelik Fabrikasi Maliyet Yönetimi ve Üretim Takibi Daha Fazla Veriyle, Daha Hizli Hareket: Yaraticiligi Aksiyonla Güçlendirme Architect Your Cloud: A Blueprint for Cloud Builders Technology Strategies that Drive Business Excellence: Get Social. Be Mobile. Run Cloud. Yeni Nesil Veri Merkezi ile BT'nin Gücünü Ortaya Çikartin Innovate with Oracle - Virtual Banking and Self Service Channels What's Next for Oracle Database?   Oracle Innova Oracle Oracle Oracle Oracle Oracle Oracle 12:40-13:40 Ögle Yemegi 13:40-14:10 Uygulamalariniz Artik Bulutta 21. Yüzyilda Finans: Potansiyeli Kullanin - Sonuçlara Ulasin! "Düsünce Hizinda" Intel Islemcili Oracle Büyük Veri ve Is Analitigi Çözümleri Deniz Seviyesinden Bulutlara I CRM'inizi Sosyallestirin: Telaura Sosyal CRM Yeni Nesil Veri Merkezinde Trend: Sadelik Abone Bilgi Yönetim Sistemi (ABYS) Yüksek Oracle Veri Tabani Performansi - Oracle Veri Tabani Oracle Veri Depolama Sistemi ile Entegre Oldugunda Sigortacilikta Finansal Transformasyon ve Entegre Veri Ambari Çözümleri SQL/PLSQL Yeni Özellikler   Oracle Oracle Intel Oracle Etiya Oracle Inspirit Oracle Oraturk TROUG 14:10-14:20  Kahve Molasi 14:20-14:50 Satis ve Pazarlamada Sosyal Mecralar Müsteri Basari Hikayeleri Paneli: Degisim Yolculugu ve Sonuçlari Tukas'in Analitik Yolculugu Deniz Seviyesinden Bulutlara II Loupe: IP Tabanli Servisler için Proaktif Izleme Veri Merkezinizdeki Riskleri Ortadan Kaldirin Oracle iAS to WebLogic Migrasyonu Oracle ZFS Storage Appliance - Turkcell Deneyimleri Analytical Transformation - Risk and Finance Together to Address the Regulatory Changes Today and Tomorrow Veri Madenciligi Veritabaninda Yapilir: Uygulamalariyla Oracle R Enterprise ve Oracle Data Mining Opsiyonu   Oracle Akbank, Teknosa, Dogus Holding, Ceynak Gtech Oracle Netas Oracle OBSS Turkcell&Gantek Oracle TROUG 14:50-15:00  Kahve Molasi 15:00-15:30 Yetenek Yönetiminde Entegre Çözümler: Taleo ile Ise Alim Artik Daha Kolay Müsteri Basari Hikayeleri Paneli: Degisim Yolculugu ve Sonuçlari Büyük Veri & Exalytics - Exadata'nin Gelecek Rotasi - Bütünlesik (Engineered) Sistemler'de Ücretsiz Platin Hizmetleri Aksigorta Oracle ATS (Application Testing Suite) ile Uygulamalarini Nasil Test Ediyor? Üstün Performans ve Esneklik ile Servis Seviyenizi Arttirin Akilli Belediyecilik Uygulamalarinda Oracle BPM ile Süreç Yönetimi Teyp ile Uçtan Uca Yedekleme Çözümleri Connecting with Customers to Enhance Revenue Generation: Unleashing the Power of an Enterprise Revenue Management and Billing Solution Günümüzün Uygulama Mimarisi Sorunlari ve Çözüm Önerileri   Oracle Akbank, Teknosa, Dogus Holding, Ceynak Oracle Oracle Aksigorta Oracle Sampas Remivac Oracle TROUG 15:30-15:40  Kahve Molasi 15:40-16:10 JD Edwards Yeni Sürüm ile Satis Agi Yönetimi Oracle Policy Automation ile Türkçe Merkezi Is Kurallari Yönetimi Oracle BI ile Kurumsal Karne Çözümleri Turkcell Süperbulut ile Yazilim Artik Hizmetinizde Bütünlesik (Engineered) Sistemler Artik SAP Müsterilerinde de Fark Yaratiyor Yeni Nesil Veri Merkezi Olusturma: Denenmis ve Ispatlanmis Yöntemler Türk Telekom SOA Projesi Basari Hikayesi Yapi Kredi Sigorta Uygulamalarinda Son Kullanici Deneyimini Nasil Izliyor? 2013 NFC Trendleri Karagöz ile Hacivat Veri Tabaninda   TupperWare & Akademi Danismanlik Oracle Oracle Turkcell Oracle Oracle Türk Telekom Yapi Kredi Sigorta Smartsoft TROUG 16:10-16:20  Kahve Molasi 16:20-16:50 Tutarli, Tekil Veriye Yolculuk: Oracle Ana Veri Yönetimi Turkcell/Superonline'da Varlik Yönetimi Her Tür Verinin Endeca ile Rahat Analizi Bulut Bilisim'de Güvenlik Nasil Saglanir? Rekabette Kazanmak: GoldenGate ile Dogru Kararlari Rakiplerinizden Önce Verin. Veri Merkeziniz için Bulut Altyapi Stratejileri Oracle Orkestrasi: Çok Sesli Yönetime Kulak Verin Lojistik Zekasi / Horoz Lojistik Basari Hikayesi Bütünlesik Sistemler (Engineered Systems) ile Yüksek Performansli Java Uygulamalari International Growth - Helping the Banks Standardize Overseas Operations Oracle Big Data   Oracle Turkcell Oracle Oracle Oracle Oracle Kora & Horoz Lojistik Oracle Oracle TROUG 16:50-18:30  Kokteyl     Eger bir kamu kurumunun/kurulusunun çalisani veya görevlisi iseniz, bu etkinlige iliskin önemli etik kurallara iliskin bilgi için lütfen buraya tiklayiniz Copyright 2012, Oracle and/or its affiliates. All rights reserved. Bize Ulasin | Yasal Uyarilar | Gizlilik Beyani

    Read the article

  • Garbled text in Screen [closed]

    - by Prabin Dahal
    The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

    Read the article

  • Évènement : eMetrics Marketing Optimization Summit, le salon de l'optimisation marketing et de la Bu

    eMetrics Marketing Optimization / SMX - l'événement webmarketing à ne pas manquer La première en France et ce sera au Hilton à Paris le 15 et 16 juin Le sommet eMetrics Marketing Optimization - l´évènement international de référence pour l´e-marketing et le « Web Analytics » - fera son entrée en France, pour la première fois le 15 et 16 juin 2010 à Paris. Depuis 2002, c´est la plateforme de rencontre des responsables marketing, des analystes web et des experts en business intelligence qui souhaitent augmenter leur retour sur investissements en ligne. Il est généralement mené en parallèle avec

    Read the article

  • What is hogging my connection?

    - by SF.
    At times it seems like dozens, if not hundreds of root-owned HTTP connections spring up. This is not much of a problem on LAN or WLAN as each of them seems to transfer very little, but if I use GPRS link, my ping times go into minutes (seriously, 80000ms is not infrequent!) and all connections grind to a halt waiting till these end. This usually lasts some 15 minutes and ends about when I start troubleshooting it for real. I've managed to capture a fragment of Nethogs output NetHogs version 0.8.0 PID USER PROGRAM DEV SENT RECEIVED ? root 37.209.147.180:59854-141.101.114.59:80 0.013 0.000 KB/sec ? root 37.209.147.180:59853-141.101.114.59:80 0.000 0.000 KB/sec ? root 37.209.147.180:52804-173.194.70.95:80 0.000 0.000 KB/sec 1954 bw /home/bw/.dropbox-dist/dropbox ppp0 0.000 0.000 KB/sec ? root 37.209.147.180:59851-141.101.114.59:80 0.000 0.000 KB/sec ? root 37.209.147.180:59850-141.101.114.59:80 0.000 0.000 KB/sec ? root 37.209.147.180:52801-173.194.70.95:80 0.000 0.000 KB/sec 13301 bw /usr/lib/firefox/firefox ppp0 0.000 0.000 KB/sec ? root unknown TCP 0.000 0.000 KB/sec Unfortunately, it doesn't display the owning process of these. Does anyone recognize these addresses or is able to suggest how to troubleshoot it further or disable it? Is it some automatic update or something like that? EDIT: per request; netstat -n, for obvious reason that normal netstat won't ever launch as all DNS requests are hogged just the same. netstat -n Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 1 93.154.166.62:51314 198.252.206.16:80 FIN_WAIT1 tcp 0 1 37.209.147.180:44098 198.252.206.16:80 FIN_WAIT1 tcp 0 1 37.209.147.180:59855 141.101.114.59:80 FIN_WAIT1 tcp 1 0 192.168.43.224:38237 213.189.45.39:443 CLOSE_WAIT tcp 1 0 93.154.146.186:35167 75.101.152.29:80 CLOSE_WAIT tcp 1 0 192.168.43.224:32939 199.15.160.100:80 CLOSE_WAIT tcp 1 0 192.168.43.224:55619 63.245.217.207:443 CLOSE_WAIT tcp 1 0 93.154.146.186:60210 75.101.152.29:443 CLOSE_WAIT tcp 1 0 192.168.43.224:32944 199.15.160.100:80 CLOSE_WAIT tcp 0 1 37.209.147.180:52804 173.194.70.95:80 FIN_WAIT1 tcp 1 0 93.154.146.186:46606 23.21.151.181:80 CLOSE_WAIT tcp 1 0 93.154.146.186:52619 107.22.246.76:80 CLOSE_WAIT tcp 415 0 93.154.146.186:36156 82.112.106.104:80 CLOSE_WAIT tcp 1 0 93.154.146.186:50352 107.22.246.76:443 CLOSE_WAIT tcp 1 0 192.168.43.224:55000 213.189.45.44:443 CLOSE_WAIT tcp 0 1 37.209.147.180:59853 141.101.114.59:80 FIN_WAIT1 tcp 1 0 192.168.43.224:32937 199.15.160.100:80 CLOSE_WAIT tcp 1 0 192.168.43.224:56055 93.184.221.40:80 CLOSE_WAIT tcp 415 0 93.154.146.186:36155 82.112.106.104:80 CLOSE_WAIT tcp 0 1 37.209.147.180:44097 198.252.206.16:80 FIN_WAIT1 tcp 1 0 93.154.146.186:35166 75.101.152.29:80 CLOSE_WAIT tcp 1 0 192.168.43.224:32943 199.15.160.100:80 CLOSE_WAIT tcp 1 0 93.154.146.186:46607 23.21.151.181:80 CLOSE_WAIT tcp 1 0 93.154.146.186:36422 23.21.151.181:443 CLOSE_WAIT tcp 1 0 192.168.43.224:36081 93.184.220.148:80 CLOSE_WAIT tcp 1 0 192.168.43.224:44462 213.189.45.29:443 CLOSE_WAIT tcp 1 0 192.168.43.224:32938 199.15.160.100:80 CLOSE_WAIT tcp 1 0 93.154.146.186:36419 23.21.151.181:443 CLOSE_WAIT tcp 0 497 93.154.166.62:51313 198.252.206.16:80 FIN_WAIT1 tcp 0 1 37.209.147.180:59851 141.101.114.59:80 FIN_WAIT1 tcp 0 1 37.209.147.180:44095 198.252.206.16:80 FIN_WAIT1 tcp 1 0 93.154.146.186:46611 23.21.151.181:80 CLOSE_WAIT tcp 1 0 192.168.43.224:38236 213.189.45.39:443 CLOSE_WAIT tcp 0 171 37.209.147.180:45341 173.194.113.146:443 ESTABLISHED tcp 0 1 37.209.147.180:52801 173.194.70.95:80 FIN_WAIT1 tcp 1 0 192.168.43.224:36080 93.184.220.148:80 CLOSE_WAIT tcp 0 1 37.209.147.180:59856 141.101.114.59:80 FIN_WAIT1 tcp 0 1 37.209.147.180:44096 198.252.206.16:80 FIN_WAIT1 tcp 0 1 93.154.166.62:57471 108.160.162.49:80 FIN_WAIT1 tcp 0 1 37.209.147.180:59854 141.101.114.59:80 FIN_WAIT1 tcp 0 171 37.209.147.180:45340 173.194.113.146:443 ESTABLISHED tcp 0 168 37.209.147.180:45334 173.194.113.146:443 FIN_WAIT1 tcp 1 0 93.154.146.186:46609 23.21.151.181:80 CLOSE_WAIT tcp 0 1248 93.154.166.62:58270 64.251.23.59:443 FIN_WAIT1 tcp 0 1 37.209.147.180:59850 141.101.114.59:80 FIN_WAIT1 tcp 1 0 93.154.146.186:35181 75.101.152.29:80 CLOSE_WAIT tcp 232 0 93.154.172.168:46384 198.252.206.25:80 ESTABLISHED tcp 1 0 93.154.146.186:52618 107.22.246.76:80 CLOSE_WAIT tcp 1 0 93.154.172.168:36298 173.194.69.95:443 CLOSE_WAIT tcp 1 0 93.154.146.186:60209 75.101.152.29:443 CLOSE_WAIT tcp 0 168 37.209.147.180:45335 173.194.113.146:443 FIN_WAIT1 tcp 415 0 93.154.146.186:36157 82.112.106.104:80 CLOSE_WAIT tcp 1 0 192.168.43.224:36082 93.184.220.148:80 CLOSE_WAIT tcp 1 0 192.168.43.224:32942 199.15.160.100:80 CLOSE_WAIT tcp 1 0 93.154.146.186:50350 107.22.246.76:443 CLOSE_WAIT tcp 1 0 192.168.43.224:32941 199.15.160.100:80 CLOSE_WAIT tcp 0 534 37.209.147.180:44089 198.252.206.16:80 FIN_WAIT1 tcp 1 0 93.154.146.186:46608 23.21.151.181:80 CLOSE_WAIT tcp 1 0 93.154.146.186:46612 23.21.151.181:80 CLOSE_WAIT udp 0 0 37.209.147.180:49057 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:51631 193.41.112.18:53 ESTABLISHED udp 0 0 37.209.147.180:34827 193.41.112.18:53 ESTABLISHED udp 0 0 37.209.147.180:35908 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:44106 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:42184 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:54485 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:42216 193.41.112.18:53 ESTABLISHED udp 0 0 37.209.147.180:51961 193.41.112.14:53 ESTABLISHED udp 0 0 37.209.147.180:48412 193.41.112.14:53 ESTABLISHED The interesting lines from ping got lost, but the summary over past few hours is: --- 8.8.8.8 ping statistics --- 107459 packets transmitted, 104376 received, +22 duplicates, 2% packet loss, time 195427362ms rtt min/avg/max/mdev = 24.822/528.132/90538.257/2519.263 ms, pipe 90 EDIT: Per request: Happened again, reboot didn't help but cleaned up all "hanging" processes. Currently netstat shows: bw@pony:/var/log$ netstat -n -t Active Internet connections (w/o servers) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 93.154.188.68:42767 74.125.239.143:443 TIME_WAIT tcp 0 0 93.154.188.68:50270 173.194.69.189:443 ESTABLISHED tcp 0 0 93.154.188.68:45250 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:53488 173.194.32.198:80 ESTABLISHED tcp 0 0 93.154.188.68:53490 173.194.32.198:80 ESTABLISHED tcp 0 159 93.154.188.68:42741 74.125.239.143:443 LAST_ACK tcp 0 0 93.154.188.68:45808 198.252.206.25:80 ESTABLISHED tcp 0 0 93.154.188.68:52449 173.194.32.199:443 ESTABLISHED tcp 0 0 93.154.188.68:52600 173.194.32.199:443 TIME_WAIT tcp 0 0 93.154.188.68:50300 173.194.69.189:443 TIME_WAIT tcp 0 0 93.154.188.68:45253 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:46252 173.194.32.204:443 ESTABLISHED tcp 0 0 93.154.188.68:45246 190.93.244.58:80 ESTABLISHED tcp 0 0 93.154.188.68:47064 173.194.113.143:443 ESTABLISHED tcp 0 0 93.154.188.68:34484 173.194.69.95:443 ESTABLISHED tcp 0 0 93.154.188.68:45252 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:54290 173.194.32.202:443 ESTABLISHED tcp 0 0 93.154.188.68:47063 173.194.113.143:443 ESTABLISHED tcp 0 0 93.154.188.68:53469 173.194.32.198:80 TIME_WAIT tcp 0 0 93.154.188.68:45242 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:53468 173.194.32.198:80 ESTABLISHED tcp 0 0 93.154.188.68:50299 173.194.69.189:443 TIME_WAIT tcp 0 0 93.154.188.68:42764 74.125.239.143:443 TIME_WAIT tcp 0 0 93.154.188.68:45256 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:58047 108.160.162.105:80 ESTABLISHED tcp 0 0 93.154.188.68:45249 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:50297 173.194.69.189:443 TIME_WAIT tcp 0 0 93.154.188.68:53470 173.194.32.198:80 ESTABLISHED tcp 0 0 93.154.188.68:34100 68.232.35.121:443 ESTABLISHED tcp 0 0 93.154.188.68:42758 74.125.239.143:443 ESTABLISHED tcp 0 0 93.154.188.68:42765 74.125.239.143:443 TIME_WAIT tcp 0 0 93.154.188.68:39000 173.194.69.95:80 TIME_WAIT tcp 0 0 93.154.188.68:50296 173.194.69.189:443 TIME_WAIT tcp 0 0 93.154.188.68:53467 173.194.32.198:80 ESTABLISHED tcp 0 0 93.154.188.68:42766 74.125.239.143:443 TIME_WAIT tcp 0 0 93.154.188.68:45251 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:45248 190.93.244.58:80 TIME_WAIT tcp 0 0 93.154.188.68:45247 190.93.244.58:80 ESTABLISHED tcp 0 159 93.154.188.68:50254 173.194.69.189:443 LAST_ACK tcp 0 0 93.154.188.68:34483 173.194.69.95:443 ESTABLISHED Output of ps: USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND root 1 0.8 0.0 3628 2092 ? Ss 16:52 0:03 /sbin/init root 2 0.0 0.0 0 0 ? S 16:52 0:00 [kthreadd] root 3 0.1 0.0 0 0 ? S 16:52 0:00 [ksoftirqd/0] root 4 0.1 0.0 0 0 ? S 16:52 0:00 [kworker/0:0] root 6 0.0 0.0 0 0 ? S 16:52 0:00 [migration/0] root 7 0.0 0.0 0 0 ? S 16:52 0:00 [watchdog/0] root 8 0.0 0.0 0 0 ? S 16:52 0:00 [migration/1] root 10 0.1 0.0 0 0 ? S 16:52 0:00 [ksoftirqd/1] root 11 0.0 0.0 0 0 ? S 16:52 0:00 [watchdog/1] root 12 0.0 0.0 0 0 ? S 16:52 0:00 [migration/2] root 14 0.1 0.0 0 0 ? S 16:52 0:00 [ksoftirqd/2] root 15 0.0 0.0 0 0 ? S 16:52 0:00 [watchdog/2] root 16 0.0 0.0 0 0 ? S 16:52 0:00 [migration/3] root 17 0.0 0.0 0 0 ? S 16:52 0:00 [kworker/3:0] root 18 0.1 0.0 0 0 ? S 16:52 0:00 [ksoftirqd/3] root 19 0.0 0.0 0 0 ? S 16:52 0:00 [watchdog/3] root 20 0.0 0.0 0 0 ? S< 16:52 0:00 [cpuset] root 21 0.0 0.0 0 0 ? S< 16:52 0:00 [khelper] root 22 0.0 0.0 0 0 ? S 16:52 0:00 [kdevtmpfs] root 23 0.0 0.0 0 0 ? S< 16:52 0:00 [netns] root 24 0.0 0.0 0 0 ? S 16:52 0:00 [sync_supers] root 25 0.0 0.0 0 0 ? S 16:52 0:00 [bdi-default] root 26 0.0 0.0 0 0 ? S< 16:52 0:00 [kintegrityd] root 27 0.0 0.0 0 0 ? S< 16:52 0:00 [kblockd] root 28 0.0 0.0 0 0 ? S< 16:52 0:00 [ata_sff] root 29 0.0 0.0 0 0 ? S 16:52 0:00 [khubd] root 30 0.0 0.0 0 0 ? S< 16:52 0:00 [md] root 42 0.0 0.0 0 0 ? S 16:52 0:00 [khungtaskd] root 43 0.0 0.0 0 0 ? S 16:52 0:00 [kswapd0] root 44 0.0 0.0 0 0 ? SN 16:52 0:00 [ksmd] root 45 0.0 0.0 0 0 ? SN 16:52 0:00 [khugepaged] root 46 0.0 0.0 0 0 ? S 16:52 0:00 [fsnotify_mark] root 47 0.0 0.0 0 0 ? S 16:52 0:00 [ecryptfs-kthrea] root 48 0.0 0.0 0 0 ? S< 16:52 0:00 [crypto] root 59 0.0 0.0 0 0 ? S< 16:52 0:00 [kthrotld] root 70 0.1 0.0 0 0 ? S 16:52 0:00 [kworker/2:1] root 71 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_0] root 72 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_1] root 73 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_2] root 74 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_3] root 75 0.0 0.0 0 0 ? S 16:52 0:00 [kworker/u:2] root 76 0.0 0.0 0 0 ? S 16:52 0:00 [kworker/u:3] root 79 0.0 0.0 0 0 ? S 16:52 0:00 [kworker/1:1] root 99 0.0 0.0 0 0 ? S< 16:52 0:00 [deferwq] root 100 0.0 0.0 0 0 ? S< 16:52 0:00 [charger_manager] root 101 0.0 0.0 0 0 ? S< 16:52 0:00 [devfreq_wq] root 102 0.1 0.0 0 0 ? S 16:52 0:00 [kworker/2:2] root 106 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_4] root 107 0.0 0.0 0 0 ? S 16:52 0:00 [usb-storage] root 108 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_5] root 109 0.0 0.0 0 0 ? S 16:52 0:00 [usb-storage] root 271 0.1 0.0 0 0 ? S 16:52 0:00 [kworker/1:2] root 316 0.0 0.0 0 0 ? S 16:52 0:00 [jbd2/sda1-8] root 317 0.0 0.0 0 0 ? S< 16:52 0:00 [ext4-dio-unwrit] root 440 0.1 0.0 2820 608 ? S 16:52 0:00 upstart-udev-bridge --daemon root 478 0.0 0.0 3460 1648 ? Ss 16:52 0:00 /sbin/udevd --daemon root 632 0.0 0.0 3348 1336 ? S 16:52 0:00 /sbin/udevd --daemon root 633 0.0 0.0 3348 1204 ? S 16:52 0:00 /sbin/udevd --daemon root 782 0.0 0.0 2816 596 ? S 16:52 0:00 upstart-socket-bridge --daemon root 822 0.0 0.0 6684 2400 ? Ss 16:52 0:00 /usr/sbin/sshd -D 102 834 0.2 0.0 4064 1864 ? Ss 16:52 0:01 dbus-daemon --system --fork root 857 0.0 0.1 7420 3380 ? Ss 16:52 0:00 /usr/sbin/modem-manager root 858 0.0 0.0 4784 1636 ? Ss 16:52 0:00 /usr/sbin/bluetoothd syslog 860 0.0 0.0 31068 1496 ? Sl 16:52 0:00 rsyslogd -c5 root 869 0.1 0.1 24280 5564 ? Ssl 16:52 0:00 NetworkManager avahi 883 0.0 0.0 3448 1488 ? S 16:52 0:00 avahi-daemon: running [pony.local] avahi 884 0.0 0.0 3448 436 ? S 16:52 0:00 avahi-daemon: chroot helper root 885 0.0 0.0 0 0 ? S< 16:52 0:00 [kpsmoused] root 892 0.0 0.1 25696 4140 ? Sl 16:52 0:00 /usr/lib/policykit-1/polkitd --no-debug root 923 0.0 0.0 0 0 ? S 16:52 0:00 [scsi_eh_6] root 959 0.0 0.0 0 0 ? S< 16:52 0:00 [krfcommd] root 970 0.0 0.1 7536 3120 ? Ss 16:52 0:00 /usr/sbin/cupsd -F colord 976 0.1 0.3 55080 10396 ? Sl 16:52 0:00 /usr/lib/i386-linux-gnu/colord/colord root 979 0.0 0.0 4632 872 tty4 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty4 root 987 0.0 0.0 4632 884 tty5 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty5 root 994 0.0 0.0 4632 884 tty2 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty2 root 995 0.0 0.0 4632 868 tty3 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty3 root 998 0.0 0.0 4632 876 tty6 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty6 root 1022 0.0 0.0 2176 680 ? Ss 16:52 0:00 acpid -c /etc/acpi/events -s /var/run/acpid.socket root 1029 0.0 0.0 3632 664 ? Ss 16:52 0:00 /usr/sbin/irqbalance daemon 1030 0.0 0.0 2476 120 ? Ss 16:52 0:00 atd root 1031 0.0 0.0 2620 880 ? Ss 16:52 0:00 cron root 1061 0.1 0.0 0 0 ? S 16:52 0:00 [kworker/3:2] root 1064 0.0 1.0 34116 31072 ? SLsl 16:52 0:00 lightdm root 1076 13.4 1.2 118688 37920 tty7 Ssl+ 16:52 0:55 /usr/bin/X :0 -core -auth /var/run/lightdm/root/:0 -nolisten tcp vt7 -novtswit root 1085 0.0 0.0 0 0 ? S 16:52 0:00 [rts_pstor] root 1087 0.0 0.0 0 0 ? S 16:52 0:00 [rtsx-polling] root 1095 0.0 0.0 0 0 ? S< 16:52 0:00 [cfg80211] root 1127 0.0 0.0 0 0 ? S 16:52 0:00 [flush-8:0] root 1130 0.0 0.0 6136 1824 ? Ss 16:52 0:00 /sbin/wpa_supplicant -B -P /run/sendsigs.omit.d/wpasupplicant.pid -u -s -O /va root 1137 0.0 0.1 24604 3164 ? Sl 16:52 0:00 /usr/lib/accountsservice/accounts-daemon root 1140 0.0 0.0 0 0 ? S< 16:52 0:00 [hd-audio0] root 1188 0.0 0.1 34308 3420 ? Sl 16:52 0:00 /usr/sbin/console-kit-daemon --no-daemon root 1425 0.0 0.0 4632 872 tty1 Ss+ 16:52 0:00 /sbin/getty -8 38400 tty1 root 1443 0.1 0.1 29460 4664 ? Sl 16:52 0:00 /usr/lib/upower/upowerd root 1579 0.0 0.1 16540 3272 ? Sl 16:53 0:00 lightdm --session-child 12 19 bw 1623 0.0 0.0 2232 644 ? Ss 16:53 0:00 /bin/sh /usr/bin/startkde bw 1672 0.0 0.0 4092 204 ? Ss 16:53 0:00 /usr/bin/ssh-agent /usr/bin/gpg-agent --daemon --sh --write-env-file=/home/bw/ bw 1673 0.0 0.0 5492 384 ? Ss 16:53 0:00 /usr/bin/gpg-agent --daemon --sh --write-env-file=/home/bw/.gnupg/gpg-agent-in bw 1676 0.0 0.0 3848 792 ? S 16:53 0:00 /usr/bin/dbus-launch --exit-with-session /usr/bin/startkde bw 1677 0.5 0.0 5384 2180 ? Ss 16:53 0:02 //bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session root 1704 0.3 0.1 25348 3600 ? Sl 16:53 0:01 /usr/lib/udisks/udisks-daemon root 1705 0.0 0.0 6620 728 ? S 16:53 0:00 udisks-daemon: not polling any devices bw 1736 0.0 0.0 2008 64 ? S 16:53 0:00 /usr/lib/kde4/libexec/start_kdeinit +kcminit_startup bw 1737 0.0 0.5 115200 15588 ? Ss 16:53 0:00 kdeinit4: kdeinit4 Running... bw 1738 0.1 0.2 116756 8728 ? S 16:53 0:00 kdeinit4: klauncher [kdeinit] --fd=9 bw 1740 0.6 1.0 340524 31264 ? Sl 16:53 0:02 kdeinit4: kded4 [kdeinit] bw 1742 0.0 0.0 8944 2144 ? S 16:53 0:00 /usr/lib/i386-linux-gnu/gconf/gconfd-2 bw 1746 0.2 0.4 92028 14688 ? S 16:53 0:00 /usr/bin/kglobalaccel bw 1748 0.0 0.4 90804 13500 ? S 16:53 0:00 /usr/bin/kwalletd bw 1752 0.1 0.5 103764 15152 ? S 16:53 0:00 /usr/bin/kactivitymanagerd bw 1758 0.0 0.0 2144 280 ? S 16:53 0:00 kwrapper4 ksmserver bw 1759 0.1 0.5 150016 16088 ? Sl 16:53 0:00 kdeinit4: ksmserver [kdeinit] bw 1763 2.2 1.0 178492 32100 ? Sl 16:53 0:08 kwin bw 1772 0.2 0.5 106292 16340 ? Sl 16:53 0:00 /usr/bin/knotify4 bw 1777 0.9 1.1 246120 32912 ? Sl 16:53 0:03 /usr/bin/krunner bw 1778 6.3 2.7 389884 80216 ? Sl 16:53 0:23 /usr/bin/plasma-desktop bw 1785 0.0 0.0 2844 1208 ? S 16:53 0:00 ksysguardd bw 1789 0.1 0.4 82036 14176 ? S 16:53 0:00 /usr/bin/kuiserver bw 1805 0.3 0.1 61560 5612 ? Sl 16:53 0:01 /usr/bin/akonadi_control root 1806 0.0 0.0 0 0 ? S 16:53 0:00 [kworker/0:2] bw 1808 0.1 0.2 211852 8460 ? Sl 16:53 0:00 akonadiserver bw 1810 0.4 0.8 244116 25360 ? Sl 16:53 0:01 /usr/sbin/mysqld --defaults-file=/home/bw/.local/share/akonadi/mysql.conf --da bw 1874 0.0 0.0 35284 2956 ? Sl 16:53 0:00 /usr/bin/xsettings-kde bw 1876 0.0 0.3 68776 9488 ? Sl 16:53 0:00 /usr/bin/nepomukserver bw 1884 0.4 0.9 173876 29240 ? SNl 16:53 0:01 /usr/bin/nepomukservicestub nepomukstorage bw 1902 6.1 2.1 451512 63924 ? Sl 16:53 0:21 /home/bw/.dropbox-dist/dropbox bw 1906 3.8 1.0 142368 32376 ? Rl 16:53 0:13 /usr/bin/yakuake bw 1933 0.0 0.1 54636 4680 ? Sl 16:53 0:00 /usr/bin/zeitgeist-datahub bw 1943 0.5 1.5 164836 46836 ? Sl 16:53 0:01 python /usr/bin/printer-applet bw 1945 0.1 0.1 99636 5048 ? S<l 16:53 0:00 /usr/bin/pulseaudio --start --log-target=syslog rtkit 1947 0.0 0.0 21336 1248 ? SNl 16:53 0:00 /usr/lib/rtkit/rtkit-daemon bw 1958 0.0 0.1 44204 3792 ? Sl 16:53 0:00 /usr/bin/zeitgeist-daemon bw 1972 0.0 0.0 27008 2684 ? Sl 16:53 0:00 /usr/lib/gvfs/gvfsd bw 1974 0.1 0.5 90480 16660 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_akonotes_resource akonadi_akonotes_res bw 1984 0.1 0.5 90472 16636 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_akonotes_resource akonadi_akonotes_res bw 1985 0.3 0.9 148800 28304 ? S 16:53 0:01 /usr/bin/akonadi_archivemail_agent --identifier akonadi_archivemail_agent bw 1992 0.1 0.5 90020 16148 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_contacts_resource akonadi_contacts_res bw 1993 0.1 0.5 90132 16452 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_contacts_resource akonadi_contacts_res bw 1994 0.1 0.5 90564 16332 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_ical_resource akonadi_ical_resource_0 bw 1995 0.1 0.5 90676 16732 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_ical_resource akonadi_ical_resource_1 bw 1996 0.1 0.5 90468 16800 ? Sl 16:53 0:00 /usr/bin/akonadi_agent_launcher akonadi_maildir_resource akonadi_maildir_resou bw 1999 0.2 0.6 99324 19276 ? S 16:53 0:00 /usr/bin/akonadi_maildispatcher_agent --identifier akonadi_maildispatcher_agen bw 2006 0.3 0.9 148808 28332 ? S 16:53 0:01 /usr/bin/akonadi_mailfilter_agent --identifier akonadi_mailfilter_agent bw 2017 0.0 0.1 50256 4716 ? Sl 16:53 0:00 /usr/lib/zeitgeist/zeitgeist-fts bw 2024 0.2 0.6 103632 18376 ? Sl 16:53 0:00 /usr/bin/akonadi_nepomuk_feeder --identifier akonadi_nepomuk_feeder bw 2043 0.0 0.0 4484 280 ? S 16:53 0:00 /bin/cat bw 2101 0.2 0.7 113600 22396 ? Sl 16:53 0:00 /usr/lib/kde4/libexec/polkit-kde-authentication-agent-1 bw 2105 0.2 0.7 114196 22072 ? Sl 16:53 0:00 /usr/bin/nepomukcontroller bw 2156 0.3 1.0 333188 31244 ? Sl 16:54 0:01 /usr/bin/kmix bw 2167 0.0 0.0 6548 2724 pts/2 Ss 16:54 0:00 /bin/bash bw 2177 0.2 0.7 113496 22960 ? Sl 16:54 0:00 /usr/bin/klipper bw 2394 3.5 1.2 52932 35596 ? SNl 16:54 0:11 /usr/bin/virtuoso-t +foreground +configfile /tmp/virtuoso_hX1884.ini +wait root 2460 0.0 0.0 6184 1876 pts/2 S 16:54 0:00 sudo -s root 2500 0.0 0.0 6528 2700 pts/2 S 16:54 0:00 /bin/bash root 2599 0.0 0.0 5444 1280 pts/2 S+ 16:54 0:00 /bin/bash bin/aero root 2606 0.1 0.0 9836 2500 pts/2 S+ 16:54 0:00 wvdial aero2 root 2619 0.0 0.0 3504 1280 pts/2 S 16:54 0:00 /usr/sbin/pppd 57600 modem crtscts defaultroute usehostname -detach user aero bw 2653 0.0 0.0 6600 2880 pts/3 Ss 16:54 0:00 /bin/bash bw 2676 0.4 0.8 130296 24016 ? SNl 16:54 0:01 /usr/bin/nepomukservicestub nepomukfilewatch bw 2679 0.1 0.7 101636 22252 ? SNl 16:54 0:00 /usr/bin/nepomukservicestub nepomukqueryservice bw 2681 0.2 0.8 109836 24280 ? SNl 16:54 0:00 /usr/bin/nepomukservicestub nepomukbackupsync bw 3833 46.0 9.7 829272 288012 ? Rl 16:55 1:46 /usr/lib/firefox/firefox bw 3903 0.0 0.0 35128 2804 ? Sl 16:55 0:00 /usr/lib/at-spi2-core/at-spi-bus-launcher bw 4708 0.1 0.0 6564 2736 pts/4 Ss 16:56 0:00 /bin/bash root 5210 0.0 0.0 0 0 ? S 16:57 0:00 [kworker/u:0] root 6140 0.2 0.0 0 0 ? S 16:58 0:00 [kworker/0:1] root 6371 0.5 0.0 6184 1868 pts/4 S+ 16:59 0:00 sudo nethogs ppp0 root 6411 17.7 0.2 8616 6144 pts/4 S+ 16:59 0:05 nethogs ppp0 bw 6787 0.0 0.0 5464 1220 pts/3 R+ 16:59 0:00 ps auxw

    Read the article

  • Making hosts accessible between LAN subnets

    - by nixnotwin
    I have two inerfaces on my router with tomato firmwre: br0 and vlan4. br0 is on 192.168.0.0/16 subnet and vlan4 on 10.0.1.0/24 subnet. As I don't want the different network services on br0 available on vlan4, I have added this firewall rule: iptables -I INPUT -i vlan4 -j ACCEPT; iptables -I FORWARD -i vlan4 -o vlan2 -m state --state NEW -j ACCEPT; iptables -I FORWARD -i br0 -o vlan4 -j DROP; vlan2 is my WAN (internet acess). The issue that I want to solve is that I want to make one host from 192.168.0.0/16 network (br0), which has ip 192.168.0.50, available on vlan4 (10.0.1.0/24). Only that host should be available on vlan4 (and all other hosts on br0 should be inaccessible). What firewall rules can be used to do it? Edit 1: Output of iptables -nvL FORWARD: Chain FORWARD (policy DROP 4 packets, 204 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- vlan4 192.168.0.50 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan4 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 229 13483 ACCEPT all -- vlan4 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 DROP all -- br0 vlan3 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan3 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 67 3405 ACCEPT all -- vlan3 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 ACCEPT all -- br0 br0 0.0.0.0/0 0.0.0.0/0 34 1360 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 758 40580 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 11781 2111K restrict all -- * vlan2 0.0.0.0/0 0.0.0.0/0 26837 19M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 wanin all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 287 15927 wanout all -- * vlan2 0.0.0.0/0 0.0.0.0/0 283 15723 ACCEPT all -- br0 * 0.0.0.0/0 0.0.0.0/0 0 0 upnp all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 Output of iptables -t nat -nvL PREROUTING: Chain PREROUTING (policy ACCEPT 6887 packets, 526K bytes) pkts bytes target prot opt in out source destination 855 83626 WANPREROUTING all -- * * 0.0.0.0/0 222.228.137.223 0 0 DROP all -- vlan2 * 0.0.0.0/0 192.168.0.0/16 0 0 DNAT udp -- * * 192.168.0.0/16 !192.168.0.0/16 udp dpt:53 to:192.168.0.1

    Read the article

  • networking tunnel adapter connections?

    - by Karthik Balaguru
    I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

    Read the article

  • Cost Comparison Hard Disk Drive to Solid State Drive on Price per Gigabyte - dispelling a myth!

    - by tonyrogerson
    It is often said that Hard Disk Drive storage is significantly cheaper per GiByte than Solid State Devices – this is wholly inaccurate within the database space. People need to look at the cost of the complete solution and not just a single component part in isolation to what is really required to meet the business requirement. Buying a single Hitachi Ultrastar 600GB 3.5” SAS 15Krpm hard disk drive will cost approximately £239.60 (http://scan.co.uk, 22nd March 2012) compared to an OCZ 600GB Z-Drive R4 CM84 PCIe costing £2,316.54 (http://scan.co.uk, 22nd March 2012); I’ve not included FusionIO ioDrive because there is no public pricing available for it – something I never understand and personally when companies do this I immediately think what are they hiding, luckily in FusionIO’s case the product is proven though is expensive compared to OCZ enterprise offerings. On the face of it the single 15Krpm hard disk has a price per GB of £0.39, the SSD £3.86; this is what you will see in the press and this is what sales people will use in comparing the two technologies – do not be fooled by this bullshit people! What is the requirement? The requirement is the database will have a static size of 400GB kept static through archiving so growth and trim will balance the database size, the client requires resilience, there will be several hundred call centre staff querying the database where queries will read a small amount of data but there will be no hot spot in the data so the randomness will come across the entire 400GB of the database, estimates predict that the IOps required will be approximately 4,000IOps at peak times, because it’s a call centre system the IO latency is important and must remain below 5ms per IO. The balance between read and write is 70% read, 30% write. The requirement is now defined and we have three of the most important pieces of the puzzle – space required, estimated IOps and maximum latency per IO. Something to consider with regard SQL Server; write activity requires synchronous IO to the storage media specifically the transaction log; that means the write thread will wait until the IO is completed and hardened off until the thread can continue execution, the requirement has stated that 30% of the system activity will be write so we can expect a high amount of synchronous activity. The hardware solution needs to be defined; two possible solutions: hard disk or solid state based; the real question now is how many hard disks are required to achieve the IO throughput, the latency and resilience, ditto for the solid state. Hard Drive solution On a test on an HP DL380, P410i controller using IOMeter against a single 15Krpm 146GB SAS drive, the throughput given on a transfer size of 8KiB against a 40GiB file on a freshly formatted disk where the partition is the only partition on the disk thus the 40GiB file is on the outer edge of the drive so more sectors can be read before head movement is required: For 100% sequential IO at a queue depth of 16 with 8 worker threads 43,537 IOps at an average latency of 2.93ms (340 MiB/s), for 100% random IO at the same queue depth and worker threads 3,733 IOps at an average latency of 34.06ms (34 MiB/s). The same test was done on the same disk but the test file was 130GiB: For 100% sequential IO at a queue depth of 16 with 8 worker threads 43,537 IOps at an average latency of 2.93ms (340 MiB/s), for 100% random IO at the same queue depth and worker threads 528 IOps at an average latency of 217.49ms (4 MiB/s). From the result it is clear random performance gets worse as the disk fills up – I’m currently writing an article on short stroking which will cover this in detail. Given the work load is random in nature looking at the random performance of the single drive when only 40 GiB of the 146 GB is used gives near the IOps required but the latency is way out. Luckily I have tested 6 x 15Krpm 146GB SAS 15Krpm drives in a RAID 0 using the same test methodology, for the same test above on a 130 GiB for each drive added the performance boost is near linear, for each drive added throughput goes up by 5 MiB/sec, IOps by 700 IOps and latency reducing nearly 50% per drive added (172 ms, 94 ms, 65 ms, 47 ms, 37 ms, 30 ms). This is because the same 130GiB is spread out more as you add drives 130 / 1, 130 / 2, 130 / 3 etc. so implicit short stroking is occurring because there is less file on each drive so less head movement required. The best latency is still 30 ms but we have the IOps required now, but that’s on a 130GiB file and not the 400GiB we need. Some reality check here: a) the drive randomness is more likely to be 50/50 and not a full 100% but the above has highlighted the effect randomness has on the drive and the more a drive fills with data the worse the effect. For argument sake let us assume that for the given workload we need 8 disks to do the job, for resilience reasons we will need 16 because we need to RAID 1+0 them in order to get the throughput and the resilience, RAID 5 would degrade performance. Cost for hard drives: 16 x £239.60 = £3,833.60 For the hard drives we will need disk controllers and a separate external disk array because the likelihood is that the server itself won’t take the drives, a quick spec off DELL for a PowerVault MD1220 which gives the dual pathing with 16 disks 146GB 15Krpm 2.5” disks is priced at £7,438.00, note its probably more once we had two controller cards to sit in the server in, racking etc. Minimum cost taking the DELL quote as an example is therefore: {Cost of Hardware} / {Storage Required} £7,438.60 / 400 = £18.595 per GB £18.59 per GiB is a far cry from the £0.39 we had been told by the salesman and the myth. Yes, the storage array is composed of 16 x 146 disks in RAID 10 (therefore 8 usable) giving an effective usable storage availability of 1168GB but the actual storage requirement is only 400 and the extra disks have had to be purchased to get the  IOps up. Solid State Drive solution A single card significantly exceeds the IOps and latency required, for resilience two will be required. ( £2,316.54 * 2 ) / 400 = £11.58 per GB With the SSD solution only two PCIe sockets are required, no external disk units, no additional controllers, no redundant controllers etc. Conclusion I hope by showing you an example that the myth that hard disk drives are cheaper per GiB than Solid State has now been dispelled - £11.58 per GB for SSD compared to £18.59 for Hard Disk. I’ve not even touched on the running costs, compare the costs of running 18 hard disks, that’s a lot of heat and power compared to two PCIe cards!Just a quick note: I've left a fair amount of information out due to this being a blog! If in doubt, email me :)I'll also deal with the myth that SSD's wear out at a later date as well - that's just way over done still, yes, 5 years ago, but now - no.

    Read the article

  • C#/.NET Little Wonders: The Generic Func Delegates

    - by James Michael Hare
    Once again, in this series of posts I look at the parts of the .NET Framework that may seem trivial, but can help improve your code by making it easier to write and maintain. The index of all my past little wonders posts can be found here. Back in one of my three original “Little Wonders” Trilogy of posts, I had listed generic delegates as one of the Little Wonders of .NET.  Later, someone posted a comment saying said that they would love more detail on the generic delegates and their uses, since my original entry just scratched the surface of them. Last week, I began our look at some of the handy generic delegates built into .NET with a description of delegates in general, and the Action family of delegates.  For this week, I’ll launch into a look at the Func family of generic delegates and how they can be used to support generic, reusable algorithms and classes. Quick Delegate Recap Delegates are similar to function pointers in C++ in that they allow you to store a reference to a method.  They can store references to either static or instance methods, and can actually be used to chain several methods together in one delegate. Delegates are very type-safe and can be satisfied with any standard method, anonymous method, or a lambda expression.  They can also be null as well (refers to no method), so care should be taken to make sure that the delegate is not null before you invoke it. Delegates are defined using the keyword delegate, where the delegate’s type name is placed where you would typically place the method name: 1: // This delegate matches any method that takes string, returns nothing 2: public delegate void Log(string message); This delegate defines a delegate type named Log that can be used to store references to any method(s) that satisfies its signature (whether instance, static, lambda expression, etc.). Delegate instances then can be assigned zero (null) or more methods using the operator = which replaces the existing delegate chain, or by using the operator += which adds a method to the end of a delegate chain: 1: // creates a delegate instance named currentLogger defaulted to Console.WriteLine (static method) 2: Log currentLogger = Console.Out.WriteLine; 3:  4: // invokes the delegate, which writes to the console out 5: currentLogger("Hi Standard Out!"); 6:  7: // append a delegate to Console.Error.WriteLine to go to std error 8: currentLogger += Console.Error.WriteLine; 9:  10: // invokes the delegate chain and writes message to std out and std err 11: currentLogger("Hi Standard Out and Error!"); While delegates give us a lot of power, it can be cumbersome to re-create fairly standard delegate definitions repeatedly, for this purpose the generic delegates were introduced in various stages in .NET.  These support various method types with particular signatures. Note: a caveat with generic delegates is that while they can support multiple parameters, they do not match methods that contains ref or out parameters. If you want to a delegate to represent methods that takes ref or out parameters, you will need to create a custom delegate. We’ve got the Func… delegates Just like it’s cousin, the Action delegate family, the Func delegate family gives us a lot of power to use generic delegates to make classes and algorithms more generic.  Using them keeps us from having to define a new delegate type when need to make a class or algorithm generic. Remember that the point of the Action delegate family was to be able to perform an “action” on an item, with no return results.  Thus Action delegates can be used to represent most methods that take 0 to 16 arguments but return void.  You can assign a method The Func delegate family was introduced in .NET 3.5 with the advent of LINQ, and gives us the power to define a function that can be called on 0 to 16 arguments and returns a result.  Thus, the main difference between Action and Func, from a delegate perspective, is that Actions return nothing, but Funcs return a result. The Func family of delegates have signatures as follows: Func<TResult> – matches a method that takes no arguments, and returns value of type TResult. Func<T, TResult> – matches a method that takes an argument of type T, and returns value of type TResult. Func<T1, T2, TResult> – matches a method that takes arguments of type T1 and T2, and returns value of type TResult. Func<T1, T2, …, TResult> – and so on up to 16 arguments, and returns value of type TResult. These are handy because they quickly allow you to be able to specify that a method or class you design will perform a function to produce a result as long as the method you specify meets the signature. For example, let’s say you were designing a generic aggregator, and you wanted to allow the user to define how the values will be aggregated into the result (i.e. Sum, Min, Max, etc…).  To do this, we would ask the user of our class to pass in a method that would take the current total, the next value, and produce a new total.  A class like this could look like: 1: public sealed class Aggregator<TValue, TResult> 2: { 3: // holds method that takes previous result, combines with next value, creates new result 4: private Func<TResult, TValue, TResult> _aggregationMethod; 5:  6: // gets or sets the current result of aggregation 7: public TResult Result { get; private set; } 8:  9: // construct the aggregator given the method to use to aggregate values 10: public Aggregator(Func<TResult, TValue, TResult> aggregationMethod = null) 11: { 12: if (aggregationMethod == null) throw new ArgumentNullException("aggregationMethod"); 13:  14: _aggregationMethod = aggregationMethod; 15: } 16:  17: // method to add next value 18: public void Aggregate(TValue nextValue) 19: { 20: // performs the aggregation method function on the current result and next and sets to current result 21: Result = _aggregationMethod(Result, nextValue); 22: } 23: } Of course, LINQ already has an Aggregate extension method, but that works on a sequence of IEnumerable<T>, whereas this is designed to work more with aggregating single results over time (such as keeping track of a max response time for a service). We could then use this generic aggregator to find the sum of a series of values over time, or the max of a series of values over time (among other things): 1: // creates an aggregator that adds the next to the total to sum the values 2: var sumAggregator = new Aggregator<int, int>((total, next) => total + next); 3:  4: // creates an aggregator (using static method) that returns the max of previous result and next 5: var maxAggregator = new Aggregator<int, int>(Math.Max); So, if we were timing the response time of a web method every time it was called, we could pass that response time to both of these aggregators to get an idea of the total time spent in that web method, and the max time spent in any one call to the web method: 1: // total will be 13 and max 13 2: int responseTime = 13; 3: sumAggregator.Aggregate(responseTime); 4: maxAggregator.Aggregate(responseTime); 5:  6: // total will be 20 and max still 13 7: responseTime = 7; 8: sumAggregator.Aggregate(responseTime); 9: maxAggregator.Aggregate(responseTime); 10:  11: // total will be 40 and max now 20 12: responseTime = 20; 13: sumAggregator.Aggregate(responseTime); 14: maxAggregator.Aggregate(responseTime); The Func delegate family is useful for making generic algorithms and classes, and in particular allows the caller of the method or user of the class to specify a function to be performed in order to generate a result. What is the result of a Func delegate chain? If you remember, we said earlier that you can assign multiple methods to a delegate by using the += operator to chain them.  So how does this affect delegates such as Func that return a value, when applied to something like the code below? 1: Func<int, int, int> combo = null; 2:  3: // What if we wanted to aggregate the sum and max together? 4: combo += (total, next) => total + next; 5: combo += Math.Max; 6:  7: // what is the result? 8: var comboAggregator = new Aggregator<int, int>(combo); Well, in .NET if you chain multiple methods in a delegate, they will all get invoked, but the result of the delegate is the result of the last method invoked in the chain.  Thus, this aggregator would always result in the Math.Max() result.  The other chained method (the sum) gets executed first, but it’s result is thrown away: 1: // result is 13 2: int responseTime = 13; 3: comboAggregator.Aggregate(responseTime); 4:  5: // result is still 13 6: responseTime = 7; 7: comboAggregator.Aggregate(responseTime); 8:  9: // result is now 20 10: responseTime = 20; 11: comboAggregator.Aggregate(responseTime); So remember, you can chain multiple Func (or other delegates that return values) together, but if you do so you will only get the last executed result. Func delegates and co-variance/contra-variance in .NET 4.0 Just like the Action delegate, as of .NET 4.0, the Func delegate family is contra-variant on its arguments.  In addition, it is co-variant on its return type.  To support this, in .NET 4.0 the signatures of the Func delegates changed to: Func<out TResult> – matches a method that takes no arguments, and returns value of type TResult (or a more derived type). Func<in T, out TResult> – matches a method that takes an argument of type T (or a less derived type), and returns value of type TResult(or a more derived type). Func<in T1, in T2, out TResult> – matches a method that takes arguments of type T1 and T2 (or less derived types), and returns value of type TResult (or a more derived type). Func<in T1, in T2, …, out TResult> – and so on up to 16 arguments, and returns value of type TResult (or a more derived type). Notice the addition of the in and out keywords before each of the generic type placeholders.  As we saw last week, the in keyword is used to specify that a generic type can be contra-variant -- it can match the given type or a type that is less derived.  However, the out keyword, is used to specify that a generic type can be co-variant -- it can match the given type or a type that is more derived. On contra-variance, if you are saying you need an function that will accept a string, you can just as easily give it an function that accepts an object.  In other words, if you say “give me an function that will process dogs”, I could pass you a method that will process any animal, because all dogs are animals.  On the co-variance side, if you are saying you need a function that returns an object, you can just as easily pass it a function that returns a string because any string returned from the given method can be accepted by a delegate expecting an object result, since string is more derived.  Once again, in other words, if you say “give me a method that creates an animal”, I can pass you a method that will create a dog, because all dogs are animals. It really all makes sense, you can pass a more specific thing to a less specific parameter, and you can return a more specific thing as a less specific result.  In other words, pay attention to the direction the item travels (parameters go in, results come out).  Keeping that in mind, you can always pass more specific things in and return more specific things out. For example, in the code below, we have a method that takes a Func<object> to generate an object, but we can pass it a Func<string> because the return type of object can obviously accept a return value of string as well: 1: // since Func<object> is co-variant, this will access Func<string>, etc... 2: public static string Sequence(int count, Func<object> generator) 3: { 4: var builder = new StringBuilder(); 5:  6: for (int i=0; i<count; i++) 7: { 8: object value = generator(); 9: builder.Append(value); 10: } 11:  12: return builder.ToString(); 13: } Even though the method above takes a Func<object>, we can pass a Func<string> because the TResult type placeholder is co-variant and accepts types that are more derived as well: 1: // delegate that's typed to return string. 2: Func<string> stringGenerator = () => DateTime.Now.ToString(); 3:  4: // This will work in .NET 4.0, but not in previous versions 5: Sequence(100, stringGenerator); Previous versions of .NET implemented some forms of co-variance and contra-variance before, but .NET 4.0 goes one step further and allows you to pass or assign an Func<A, BResult> to a Func<Y, ZResult> as long as A is less derived (or same) as Y, and BResult is more derived (or same) as ZResult. Sidebar: The Func and the Predicate A method that takes one argument and returns a bool is generally thought of as a predicate.  Predicates are used to examine an item and determine whether that item satisfies a particular condition.  Predicates are typically unary, but you may also have binary and other predicates as well. Predicates are often used to filter results, such as in the LINQ Where() extension method: 1: var numbers = new[] { 1, 2, 4, 13, 8, 10, 27 }; 2:  3: // call Where() using a predicate which determines if the number is even 4: var evens = numbers.Where(num => num % 2 == 0); As of .NET 3.5, predicates are typically represented as Func<T, bool> where T is the type of the item to examine.  Previous to .NET 3.5, there was a Predicate<T> type that tended to be used (which we’ll discuss next week) and is still supported, but most developers recommend using Func<T, bool> now, as it prevents confusion with overloads that accept unary predicates and binary predicates, etc.: 1: // this seems more confusing as an overload set, because of Predicate vs Func 2: public static SomeMethod(Predicate<int> unaryPredicate) { } 3: public static SomeMethod(Func<int, int, bool> binaryPredicate) { } 4:  5: // this seems more consistent as an overload set, since just uses Func 6: public static SomeMethod(Func<int, bool> unaryPredicate) { } 7: public static SomeMethod(Func<int, int, bool> binaryPredicate) { } Also, even though Predicate<T> and Func<T, bool> match the same signatures, they are separate types!  Thus you cannot assign a Predicate<T> instance to a Func<T, bool> instance and vice versa: 1: // the same method, lambda expression, etc can be assigned to both 2: Predicate<int> isEven = i => (i % 2) == 0; 3: Func<int, bool> alsoIsEven = i => (i % 2) == 0; 4:  5: // but the delegate instances cannot be directly assigned, strongly typed! 6: // ERROR: cannot convert type... 7: isEven = alsoIsEven; 8:  9: // however, you can assign by wrapping in a new instance: 10: isEven = new Predicate<int>(alsoIsEven); 11: alsoIsEven = new Func<int, bool>(isEven); So, the general advice that seems to come from most developers is that Predicate<T> is still supported, but we should use Func<T, bool> for consistency in .NET 3.5 and above. Sidebar: Func as a Generator for Unit Testing One area of difficulty in unit testing can be unit testing code that is based on time of day.  We’d still want to unit test our code to make sure the logic is accurate, but we don’t want the results of our unit tests to be dependent on the time they are run. One way (of many) around this is to create an internal generator that will produce the “current” time of day.  This would default to returning result from DateTime.Now (or some other method), but we could inject specific times for our unit testing.  Generators are typically methods that return (generate) a value for use in a class/method. For example, say we are creating a CacheItem<T> class that represents an item in the cache, and we want to make sure the item shows as expired if the age is more than 30 seconds.  Such a class could look like: 1: // responsible for maintaining an item of type T in the cache 2: public sealed class CacheItem<T> 3: { 4: // helper method that returns the current time 5: private static Func<DateTime> _timeGenerator = () => DateTime.Now; 6:  7: // allows internal access to the time generator 8: internal static Func<DateTime> TimeGenerator 9: { 10: get { return _timeGenerator; } 11: set { _timeGenerator = value; } 12: } 13:  14: // time the item was cached 15: public DateTime CachedTime { get; private set; } 16:  17: // the item cached 18: public T Value { get; private set; } 19:  20: // item is expired if older than 30 seconds 21: public bool IsExpired 22: { 23: get { return _timeGenerator() - CachedTime > TimeSpan.FromSeconds(30.0); } 24: } 25:  26: // creates the new cached item, setting cached time to "current" time 27: public CacheItem(T value) 28: { 29: Value = value; 30: CachedTime = _timeGenerator(); 31: } 32: } Then, we can use this construct to unit test our CacheItem<T> without any time dependencies: 1: var baseTime = DateTime.Now; 2:  3: // start with current time stored above (so doesn't drift) 4: CacheItem<int>.TimeGenerator = () => baseTime; 5:  6: var target = new CacheItem<int>(13); 7:  8: // now add 15 seconds, should still be non-expired 9: CacheItem<int>.TimeGenerator = () => baseTime.AddSeconds(15); 10:  11: Assert.IsFalse(target.IsExpired); 12:  13: // now add 31 seconds, should now be expired 14: CacheItem<int>.TimeGenerator = () => baseTime.AddSeconds(31); 15:  16: Assert.IsTrue(target.IsExpired); Now we can unit test for 1 second before, 1 second after, 1 millisecond before, 1 day after, etc.  Func delegates can be a handy tool for this type of value generation to support more testable code.  Summary Generic delegates give us a lot of power to make truly generic algorithms and classes.  The Func family of delegates is a great way to be able to specify functions to calculate a result based on 0-16 arguments.  Stay tuned in the weeks that follow for other generic delegates in the .NET Framework!   Tweet Technorati Tags: .NET, C#, CSharp, Little Wonders, Generics, Func, Delegates

    Read the article

  • networking tunnel adapter connections?

    - by Karthik Balaguru
    I understand that Tunnel Adapter LAN is for encapsulating IPv6 packets with an IPv4 header so that they can be sent across an IPv4 network. Few queries popped up in my mind based on this :- If i do 'ipconfig', Apart from ethernet adapter LAN details, I get a series of statments as below - Tunnel adapter Local Area Connection* 6 Tunnel adapter Local Area Connection* 7 Tunnel adapter Local Area Connection* 12 Tunnel adapter Local Area Connection* 13 Tunnel adapter Local Area Connection* 14 Tunnel adapter Local Area Connection* 15 Tunnel adapter Local Area Connection* 16 Except for the *16, all the other Tunnel Adapter Local Area Connections show Media Disconnected. Why is the numbering for the Tunnel adapter LAN not sequential? It is like 6, 7, 12, 13, 14, 15, 16. A strange numbering scheme! I tried to figure it out by thinking of some arithmetic series. But, it does not seem to fit in. There is a huge gap between 7 and 12. Any ideas? What is the need for so many Tunnel Adapter LAN connections? Can you tell me a scenario that requires all of those ? I did ipconfig /all to get more information. From the listing, I understand that: 16, 15, 14, 12 are Microsoft 6to4 Adapters 13, 6 are isatap Adapters 7 is Teredo Tunneling Pseudo-interface I understand that the above are for automatic tunneling so that the tunnel endpoints are determined automatically by the routing infrastructure. 6to4 is recommended by RFC3056 for automatic tunneling that uses protocol 41 for encapsulation. It is typically used when an end-user wants to connect to the IPv6 Internet using their existing IPv4 connection. Teredo is an automatic tunneling technique that uses UDP encapsulation across multiple NATs. That is, It is to grant IPv6 connectivity to nodes that are located behind IPv6-unaware NAT devices ISATAP treats the IPv4 network as a virtual IPv6 local link, with mappings from each IPv4 address to a link-local IPv6 address. That is to transmit IPv6 packets between dual-stack nodes on top of an IPv4 network. That is, to put in simple words, ISATAP is an intra-site mechanism, while the 6to4 and Teredo are for inter-site tunnelling mechanisms. It seems that Teredo should alone enabled by default in Vista, But my system does not show it to be enabled by default. Interestingly, it shows a 6to4 tunnel adapter (Tunnel adapter LAN connection 16) to be enabled by default? Any specific reasons for it? If i do ipconfig /all, why is only one Teredo present while four 6to4 are present ? I searched the internet for answers to the above queries, but I am unable to find clear answers.

    Read the article

  • Weird DNS bug - external server resolves to internal IP

    - by emilecantin
    I have a server that is hosted by my university. I have root access, but no control over network setup, firewall, etc. This server's DNS resolves to an internal IP here on campus (10.x.x.x), and an external IP outside campus. I also have a few servers hosted at Amazon, and they mostly work well. However, one of them started to resolve the university server by its internal IP address. This causes problems, as 10.x.x.x on Amazon EC2 is someone else. I have connected to the Amazon server with SSH agent forwarding a few times in the past, to access a Git repository on the university server. Any idea what could cause this? EDIT: Here's my /etc/resolv.conf # Generated by dhcpcd for interface eth0 search ec2.internal nameserver 172.16.0.23 Here's the output of dig myserver.myuniversity.ca.: ; <<>> DiG 9.8.1-P1 <<>> myserver.myuniversity.ca. ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 34470 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myserver.myuniversity.ca. IN A ;; ANSWER SECTION: myserver.myuniversity.ca. 537586 IN A 10.43.x.x ;; Query time: 2 msec ;; SERVER: 172.16.0.23#53(172.16.0.23) ;; WHEN: Wed Nov 28 16:07:21 2012 ;; MSG SIZE rcvd: 60 Here's the expected output (on another Amazon server): ; <<>> DiG 9.8.1-P1 <<>> myserver.myuniversity.ca. ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 8045 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;myserver.myuniversity.ca. IN A ;; ANSWER SECTION: myserver.myuniversity.ca. 601733 IN A x.x.239.1 ;; Query time: 1 msec ;; SERVER: 172.16.0.23#53(172.16.0.23) ;; WHEN: Wed Nov 28 16:09:36 2012 ;; MSG SIZE rcvd: 60

    Read the article

  • Max ram for computer 16GB or 8GB

    - by Laptop memory question
    Manufacturer's specifications for my notebook say memory can be extended from 4GB to 8GB. Whereas, running sudo dmidecode suggests the computer can use 16GB as below: Handle 0x0037, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 16 GB Error Information Handle: Not Provided Number Of Devices: 4 Which one is correct?

    Read the article

  • VPN pptp connection Unable to pass through linux iptables

    - by user221844
    I have set up a windows VPN server behind Linux - Ubuntu box that is working as firewall and proxy server. Now I want people from outside to be able to connect to the VPN server, but the connection is not being established and I get on the client an error 619. I have checked the problem on the internet and it seems a firewall issue. what should I do to make the connection established through the firewall? here is below the information about my setup Firewall-External-IF-IP: 172.16.1.100 Firewall-LAN-IF-IP: 192.168.1.1 VPN-Server-IP: 192.168.1.10 and below is my iptables file content: #Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *filter :INPUT ACCEPT [162000:140437619] :FORWARD ACCEPT [23282:27196133] :OUTPUT ACCEPT [185778:143961739] :LOGGING - [0:0] -A INPUT -p gre -j ACCEPT -A INPUT -s 192.168.1.10/32 -p tcp -m tcp --sport 1723 -j ACCEPT -A INPUT -s 192.168.1.10/32 -p udp -m udp --sport 1723 -j ACCEPT -A FORWARD -s 192.168.1.0/24 -o EXT_IF -j ACCEPT -A FORWARD -s 192.168.1.0/24 -i EXT_IF -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p tcp -m tcp --dport 1723 -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p tcp -m tcp --sport 1723 -m state --state RELATED,ESTABLISHED -j ACCEPT -A FORWARD -d 192.168.1.10/32 -i EXT_IF -o INT_IF -p gre -m state --state NEW,RELATED,ESTABLISHED -j ACCEPT -A FORWARD -s 192.168.1.10/32 -i INT_IF -o EXT_IF -p gre -m state --state RELATED,ESTABLISHED -j ACCEPT -A OUTPUT -p gre -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p tcp -m tcp --dport 1723 -j ACCEPT -A OUTPUT -d 192.168.1.10/32 -p udp -m udp --dport 1723 -j ACCEPT COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *nat :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :PREROUTING ACCEPT [17865:1053739] :INPUT ACCEPT [5490:357281] :OUTPUT ACCEPT [3723:223677] :POSTROUTING ACCEPT [3726:223870] -A PREROUTING -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p tcp -m tcp --dport 1723 -j DNAT --to-destination 192.168.1.10 -A PREROUTING -d 172.16.1.100/32 -i EXT_IF -p gre -j DNAT --to-destination 192.168.1.10 -A PREROUTING -i -h -A POSTROUTING -s 192.168.1.0/24 -o EXT_IF -j MASQUERADE COMMIT # Completed on Thu May 29 12:40:18 2014 # Generated by iptables-save v1.4.12 on Thu May 29 12:40:18 2014 *mangle :PREROUTING ACCEPT [22695965:17811993005] :INPUT ACCEPT [13818180:11522330171] :FORWARD ACCEPT [8527694:6271564562] :OUTPUT ACCEPT [14748508:11899678536] :POSTROUTING ACCEPT [23271280:18170828012] COMMIT # Completed on Thu May 29 12:40:18 2014 hope that I find the solution here ....!! :(

    Read the article

  • How to convert from wav or mp3 to raw PCM [on hold]

    - by Komyg
    I am developing a game using Cocos2d-X and Marmalade SDK, and I am looking for any recommendations of programs that can convert audio files in mp3 or wav format to raw PCM 16 format. The problem is that I am using the SimpleAudioEngine class to play sounds in my game and in Marmalade it only supports files that are encoded as raw PCM 16. Unfortunately I've been having a very hard time finding a program that can do this type of conversion, so I am looking for a recommendation.

    Read the article

  • Php 5.3.3. Access log

    - by irolla
    Hi I'm using php-fpm. In 5.3.2 when I'm opening phpinfo page in access log I get: ip - - [26/Aug/2010:16:35:32 +0400] "GET /phpinfo.php HTTP/1.1" 200 13322 "-" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091102 Firefox/3.5.5" But in 5.3.3 I'm getting: ip - - [26/Aug/2010:16:30:30 +0400] "GET /phpinfo.php HTTP/1.1" 200 11891 "-" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091102 Firefox/3.5.5" ip - - [26/Aug/2010:16:30:30 +0400] "GET /phpinfo.php?=PHPE9568F34-D428-11d2-A769-00AA001ACF42 HTTP/1.1" 200 2536 "http://site.com/phpinfo.php" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091102 Firefox/3.5.5" ip - - [26/Aug/2010:16:30:30 +0400] "GET /phpinfo.php?=SUHO8567F54-D428-14d2-A769-00DA302A5F18 HTTP/1.1" 200 2825 "http://site.com/phpinfo.php" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091102 Firefox/3.5.5" ip - - [26/Aug/2010:16:30:30 +0400] "GET /phpinfo.php?=PHPE9568F35-D428-11d2-A769-00AA001ACF42 HTTP/1.1" 200 2158 "http://site.com/phpinfo.php" "Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091102 Firefox/3.5.5" Why there is 4 lines insted of 1? And what means "?=PHPE...". Is it PHP sessions? My php5.3.3 fpm config: [global] pid = /var/run/php5-fpm.pid error_log = /var/log/php5-fpm.log log_level = notice [pool_0] listen = 127.0.0.1:9000 listen.backlog = -1 listen.allowed_clients = 127.0.0.1 user = www-data group = www-data pm = dynamic pm.max_children = 50 pm.min_spare_servers = 5 pm.max_spare_servers = 35 pm.max_requests = 500 pm.status_path = /pool_0/status rlimit_files = 1024 rlimit_core = 0 catch_workers_output = yes php_admin_flag[register_globals] = true php_admin_value[error_reporting] = E_ALL & ~E_DEPRECATED php_admin_value[max_execution_time] = 15 php_admin_flag[short_open_tag] = true php_admin_flag[display_errors] = false

    Read the article

  • Marshalling C# Structs into DX11 cbuffers

    - by Craig
    I'm having some issues with the packing of my structure in C# and passing them through to cbuffers I have registered in HLSL. When I pack my struct in one manner the information seems to be able to pass to the shader: [StructLayout(LayoutKind.Explicit, Size = 16)] internal struct TestStruct { [FieldOffset(0)] public Vector3 mEyePosition; [FieldOffset(12)] public int type; } This works perfectly when used against this HLSL fragment: cbuffer PerFrame : register(b0) { Vector3 eyePos; int type; } float3 GetColour() { float3 returnColour = float(0.0f, 0.0f, 0.0f); switch(type) { case 0: returnColour = float3(1.0f, 0.0f, 0.0f); break; case 1: returnColour = float3(0.0f, 1.0f, 0.0f); break; case 2: returnColour = float3(0.0f, 0.0f, 1.0f); break; } return returnColour; } However, when I use the following structure definitions... // Note this is 16 because HLSL packs in 4 float 'chunks'. // It is also simplified, but still demonstrates the problem. [StructLayout(Layout.Explicit, Size = 16)] internal struct InternalTestStruct { [FieldOffset(0)] public int type; } [StructLayout(LayoutKind.Explicit, Size = 32)] internal struct TestStruct { [FieldOffset(0)] public Vector3 mEyePosition; //Missing 4 bytes here for correct packing. [FieldOffset(16)] public InternalTestStruct mInternal; } ... the following HLSL fragment no longer works. struct InternalType { int type; } cbuffer PerFrame : register(b0) { Vector3 eyePos; InternalType internalStruct; } float3 GetColour() { float3 returnColour = float(0.0f, 0.0f, 0.0f); switch(internaltype.type) { case 0: returnColour = float3(1.0f, 0.0f, 0.0f); break; case 1: returnColour = float3(0.0f, 1.0f, 0.0f); break; case 2: returnColour = float3(0.0f, 0.0f, 1.0f); break; } return returnColour; } Is there a problem with the way I am packing the struct, or is it another issue? To re-iterate: I can pass a struct in a cbuffer so long as it does not contain a nested struct.

    Read the article

  • Dynamic Bind9 + DHCP

    - by AcidRod75
    i have been working on setup a server for my internal network, so far i have a working isc-dhcp-server that can upgrade a chrooted BIND9 (on the same machine), i need to add some static entries on the DNS, so users can resolve the websites that resides in our DMZ. What i had tryed all ready was to modify the /etc/bind/named.conf.local with this info: // // Do any local configuration here // // Consider adding the 1918 zones here, if they are not used in your // organization //include "/etc/bind/zones.rfc1918"; key DHCP_UPDATER { algorithm HMAC-MD5.SIG-ALG.REG.INT; secret "MySuperSecretHash"; (this is not the real value BTW) }; zone "quality.internal" IN { type master; file "/var/lib/bind/quality.internal.db"; allow-update { key DHCP_UPDATER; }; }; zone "0.10.10.in-addr.arpa" { type master; file "/var/lib/bind/rev.10.10.0.in-addr.arpa"; allow-update { key DHCP_UPDATER; }; }; logging { channel query.log { file "/var/log/named/query.log"; severity debug 3; }; category queries { query.log; }; }; --- EOF ---- then i added this 2 entries: zone "ourserver.internal" IN { type master; file "/var/lib/bind/ourserver.internal.db"; }; zone "0.16.172.in-addr.arpa" { type master; file "/var/lib/bind/rev.172.16.0.in-addr.arpa"; }; ---- EOF ---- So.. i created the files ourserver.internal.db and rev.172.16.0.in-addr.arpa placed them BOTH in /var/lib/bind/ and changed the permisions so the bind user can access them, restated the service... when i do a NSLOOKUP www.ourserver.internal i get: Server: 127.0.0.1 Address: 127.0.0.1#53 ** server can't find www.ourserver.internal: NXDOMAIN BUT when i do a reverse lookup.... Server: 127.0.0.1 Address: 127.0.0.1#53 5.0.16.172.in-addr.arpa name = www.ourserver.internal I do not understand what's wrong. Some help with this will save me from installing a new DNS server at the DMZ JUST to host internal site names- TY in advance BTW: the server i'm using has Ubuntu Server 11.10 fully patched.

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >