Search Results

Search found 41520 results on 1661 pages for 'fault tolerant'.

Page 52/1661 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• Static IP settings on Windows 2003 server not getting saved

  - by Prashant Mandhare

  We have a Dell PowerEgde 1950 server with Broadcom NetXtreme gigabit ethernet card, and we are facing a strange problem with static IP assignment. When we assign a static IP to this broadcom NIC, settings are not getting saved. Following are the steps to reproduce problem open TCP/IP properties window for broadcom NIC manually enter static IP address and other details like gateway, DNS, etc. apply and close properties dialog. re-open TCP/IP properties windows, you will see your static IP settings lost and changed to "obtain IP address manually" but when checked using ipconfig command, you will still see your same static IP settings but, when checked using ipconfig command after rebooting server, these static ip settings are completely gone and automatically obtained IP is assigned Supplementary information: Recently we had formatted this server and installed windows 2003 from OEM windows setup CD (not from OS installation CD received from Dell). After windows installation was over, broadcom NIC drivers were installed.

  Read the article

• vCenter appliance won't use mail relay server

  - by Safado

  tl;dr: - sendmail is configured to use a relay server but still insists on using 127.0.01 as the relay, which results in mail not being sent. We have the open source vCenter appliance (v 5.0) managing our ESXi cluster. When connected to it via vSphere Client, you can configure the SMTP relay server to use by going to Administration > vCenter Server Settings > MAIL. There you can set the SMTP Server value. I looked through their documentation and also confirmed on the phone with support that all you have to do to configure mail is to put in the relay IP or fqdn in that box and hit OK. Well, I had done that and mail still wasn't sending. So I SSH into the server (which is SuSE) and look at /var/log/mail and it looks like it's trying to relay the email through 127.0.0.1 and it's rejecting it. So looking through the config files, I see there's /etc/sendmail.cf and /etc/mail/submit.cf. You can configure items in /etc/sysconfig/sendmail and run SuSEconfig --module sendmail to generate those to .cf files based on what's in /etc/sysconfig/sendmail. So playing around, I see that when you set the SMTP Server value in the vCenter gui, all that it does is change the "DS" line in /etc/mail/submit.cf to have DS[myrelayserver.com]. Looking on the internet, it would appear that the DS line is really the only thing you need to change in order to use a relay server. I got on the phone with VMWare support and spent 2 hours trying to modify ANY setting that had anything to do with relays and we couldn't get it to NOT use 127.0.0.1 as the relay. Just to note, any time we made any sort of configuration change, we restarted the sendmail service. Does anyone know whats going on? Have any ideas on how I can fix this?

  Read the article

• Public free time server

  - by JL.

  I need to get the current datetime from a reliable source, because its likely that the local system time could be changed. Is it possible to get this from an internet time server, one that has close to 100% uptime, preferably via a webservice method, something that is free, and I have to stress absolutely reliable? I would hope an offering from Microsoft, or the organisation responsible for keeping global time.

  Read the article

• Zimbra server status showing red in control panel

  - by Debianuser

  I have been having a weird problem with Zimbra(7.1.4_GA_2555.DEBIAN5) lately: On the (web)control panel the status keep changing to red every few days. When this is happens the output of zmcontrol status still shows running: antispam Running antivirus Running imapproxy Running ldap Running logger Running mailbox Running memcached Running mta Running snmp Running spell Running stats Running zmconfigd Running Every thing runs fine except automated mail forwarding from one account to another(which is critical for us). I have been through Zimbra forums and the following ALWAYS fixes the issue: su - zimbra -c "zmprov mcf zimbraLogHostname mail.mydomain.com" /opt/zimbra/libexec/zmsyslogsetup /etc/init.d/rsyslog restart su - zimbra -c "zmcontrol restart" After I run the above commands, the status on control panel turns green and mail forwarding starts to work again BUT only for a few days. Other than the above, everything works fine including Server statistics. Anyone seen this issue before?

  Read the article

• 401 - Unauthorized On Server 2008 R2 IIS 7.5

  - by mxmissile

  I have a web application deployed to Server 2008 IIS 7.5 box. From remote it gives this error: 401 - Unauthorized: Access is denied due to invalid credentials. (remote = desktops on the same LAN) Have tried several remote clients using different browsers, all the same result. (IE, FF, and Chrome) Hitting the application from the desktop of the server itself works flawlessly. The application is using Anonymous Authentication. The application is written in .NET 4.0 Asp.Net using the MVC framework. Sysinternals procmon returns these 2 results for each request: FAST IO DISALLOWED and PATH NOT FOUND. I have 2 other MVC apps running fine on the same server. I have checked the security on the folders and they all match. App runs fine on a Server 2008 IIS 7.0 box. Nothing shows up in the Event log on the server related to this. Pulling my hair out here, any troubleshooting tips?

  Read the article

• Windows web server and SQL Server on same dedicated server

  - by asinc

  I'm currently trying to decide on the best approach to handle hosting a few moderate traffic websites for production e-commerce and online applications. We'd like to move to a dedicated server and are looking at this as the most likely machine: Quad Core Intel Core2Quad Q9550 Processor, 2.83 Ghz X 4, 4 GB Kingston Ram This would run Windows Web Server 2008 R2 x64 and potentially also Sql Server Web 2008 and SmarterMail server. Given that we already pay for a high-end VPS for development, testing, shared version control we'd like to avoid going with two servers for production. We'd like to avoid using shared sql server hosting and have thought of using the development server as the database server as an option too - but potentially a security risk due to use for development by internal and contract users. The questions are: - Do you feel there would be performance degradation by running this on the same machine? - Are there significant issues to be concerned about if we do this? We understand that best practice would be to run separate db and app servers but the volume of traffic is currently not that high and adding another server just for database is currently too costly. - What are others doing out there? Alternatively, would you recommend instead going with two separate VPS servers with 2GB RAM each on Hyper-v which would be about the same cost as the single dedicated server above? Thanks!

  Read the article

• MySQL won't start or won't installed

  - by Owen

  Hi there, I'm trying to get a local LAMP setup on my Ubuntu desktop. I'm successfully got PHP install but I'm having trouble with MySQL If PHP tries to connet to MySQL I get this error: Warning: mysql_connect() [function.mysql-connect]: Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) in /var/www/testing.php on line 3 Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (2) If I try via command line I get much the same error: owen@desktop:~$ mysql ERROR 2002 (HY000): Can't connect to local MySQL server through socket '/var/run/mysqld/mysqld.sock' (13) Weirdly "/var/run/mysqld" does not exist. Running a whereis command I get the following: owen@desktop:~$ whereis mysqld.sock mysqld: /usr/sbin/mysqld /usr/share/man/man8/mysqld.8.gz So is MySQL even installed? Well acording to dpkg owen@desktop:~$ dpkg -l | grep mysql ii libapache2-mod-auth-mysql 4.3.9-13ubuntu1 Apache 2 module for MySQL authentication ii libdbd-mysql-perl 4.016-1 Perl5 database interface to the MySQL database ii libmysqlclient15off 5.1.30really5.0.83-0ubuntu3 MySQL database client library ii libmysqlclient16 5.1.49-1ubuntu8.1 MySQL database client library ii mysql-admin 5.0r14+openSUSE-2.1 GUI tool for intuitive MySQL administration ii mysql-client-5.1 5.1.49-1ubuntu8.1 MySQL database client binaries ii mysql-client-core-5.1 5.1.49-1ubuntu8.1 MySQL database core client binaries ii mysql-common 5.1.49-1ubuntu8.1 MySQL database common files, e.g. /etc/mysql/my.cnf ii mysql-gui-tools-common 5.0r14+openSUSE-2.1 Architecture independent files for MySQL GUI Tools ii mysql-query-browser 5.0r14+openSUSE-2.1 Official GUI tool to query MySQL database ii mysql-server 5.1.49-1ubuntu8.1 MySQL database server (metapackage depending on the latest version) ii mysql-server-5.1 5.1.49-1ubuntu8.1 MySQL database server binaries and system database setup ii mysql-server-core-5.0 5.1.30really5.0.83-0ubuntu3 MySQL database core server files ii mysql-server-core-5.1 5.1.49-1ubuntu8.1 MySQL database server binaries ii php5-mysql Can someone please help I'm really confused as what to do next. I'm not a Linux expert at all most of these commands I've ran I found of diffrent blogs and help forums.

  Read the article

• Query specific logs from event log using nxlog

  - by user170899

  Below is my nxlog configuration define ROOT C:\Program Files (x86)\nxlog Moduledir %ROOT%\modules CacheDir %ROOT%\data Pidfile %ROOT%\data\nxlog.pid SpoolDir %ROOT%\data LogFile %ROOT%\data\nxlog.log <Extension json> Module xm_json </Extension> <Input internal> Module im_internal </Input> <Input eventlog> Module im_msvistalog Query <QueryList>\ <Query Id="0">\ <Select Path="Security">*</Select>\ </Query>\ </QueryList> </Input> <Output out> Module om_tcp Host localhost Port 3515 Exec $EventReceivedTime = integer($EventReceivedTime) / 1000000; \ to_json(); </Output> <Route 1> Path eventlog, internal => out </Route> <Select Path="Security">*</Select>\ - * gets everything from the Security log, but my requirement is to get specific logs starting with EventId - 4663. How do i do this? Please help. Thanks.

  Read the article

• Squid, NTLM, Windows 7 and IE8

  - by Harley

  I'm running Squid 2.7-stable4, Samba 3 and the Windows 7 RC with IE8. I have NTLM authentication setup on my squid proxy server and it works fine for every combination of browser and Windows (including IE8 on XP and Firefox on Win7), but it doesn't work (keeps asking for authentication) for IE8 on Windows 7. I can get it to work using the LmCompatibilityLevel registry hack, but I'd really prefer to get it working on the server. Does anyone have any experience with this? Or know where to start looking? The samba logs don't reveal much. EDIT: Here's what the wb-MYDOMAIN log says when I attempt to authenticate: [2009/08/20 15:13:36, 4] nsswitch/winbindd_dual.c:fork_domain_child(1080) child daemon request 13 [2009/08/20 15:13:36, 10] nsswitch/winbindd_dual.c:child_process_request(478) process_request: request fn AUTH_CRAP [2009/08/20 15:13:36, 3] nsswitch/winbindd_pam.c:winbindd_dual_pam_auth_crap(1755) [ 4127]: pam auth crap domain: MYDOMAIN user: MYUSER [2009/08/20 15:13:36, 0] nsswitch/winbindd_pam.c:winbindd_dual_pam_auth_crap(1767) winbindd_pam_auth_crap: invalid password length 24/282 [2009/08/20 15:13:36, 2] nsswitch/winbindd_pam.c:winbindd_dual_pam_auth_crap(1931) NTLM CRAP authentication for user [MYDOMAIN]\[MYUSER] returned NT_STATUS_INVALID_PARAMETER (PAM: 4) [2009/08/20 15:13:36, 10] nsswitch/winbindd_cache.c:cache_store_response(2267) Storing response for pid 4547, len 3240

  Read the article

• MySQL error: Can't find symbol '_mysql_plugin_interface_version_' in library

  - by Josh Smith

  The boring, necessary details: I'm on Snow Leopard running MySQL locally. I'm trying to install the Sphinx engine for MySQL like so: mysql> install plugin sphinx soname 'sphinx.so'; ERROR 1127 (HY000): Can't find symbol '_mysql_plugin_interface_version_' in library I've Googled everywhere and can't seem to find an actual solution to this problem. For example this issue on the Sphinx forums seems unresolved. Someone else also raised this issue with similar results. The first post linked to an O'Reilly article which says: There is a common problem that might occur at this point: ERROR 1127 (HY000): Can't find symbol '_mysql_plugin_interface_version_' in library If you see a message like this, it is likely that you forgot to include the -DMYSQL_DYNAMIC_PLUGIN option when compiling the plugin. Adding this option to the g++ compile line is required to create a dynamically loadable plug-in. But the article ends on that point; I have no idea what this means or how to resolve the issue.

  Read the article

• Can't get MySQL to install

  - by James Marthenal

  I'd like to think I know what I'm doing in a Unix shell but maybe not. I made a mistake in a configuration file for MySQL, so I decided to just uninstall it and then reinstall it, so I did: sudo apt-get --purge remove mysql-server mysql-server-5.0 mysql-client The files were deleted, so I then tried to install it, but it didn't ask me for a root password or anything else, so I uninstalled it using the above command again and then did sudo rm -rf /etc/mysql sudo rm /etc/init.d/mysql sudo rm -rf /var/lib/mysql* I then restarted the computer then installed it again: sudo apt-get install mysql-server mysql-client It asked for a root password, and everything looked like it would work, until I saw this: $ sudo apt-get install mysql-server mysql-client Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: mysql-server-5.0 Suggested packages: tinyca The following NEW packages will be installed: mysql-client mysql-server mysql-server-5.0 0 upgraded, 3 newly installed, 0 to remove and 1 not upgraded. Need to get 0B/27.4MB of archives. After this operation, 86.7MB of additional disk space will be used. Do you want to continue [Y/n]? y WARNING: The following packages cannot be authenticated! mysql-server-5.0 mysql-client mysql-server Authentication warning overridden. Preconfiguring packages ... Can't exec "/tmp/mysql-server-5.0.config.28101": Permission denied at /usr/share/perl/5.10/IPC/Open3.pm line 168. open2: exec of /tmp/mysql-server-5.0.config.28101 configure failed at /usr/share/perl5/Debconf/ConfModule.pm line 59 mysql-server-5.0 failed to preconfigure, with exit status 255 Selecting previously deselected package mysql-server-5.0. (Reading database ... 160284 files and directories currently installed.) Unpacking mysql-server-5.0 (from .../mysql-server-5.0_5.0.51a-24+lenny5_amd64.deb) ... Selecting previously deselected package mysql-client. Unpacking mysql-client (from .../mysql-client_5.0.51a-24+lenny5_all.deb) ... Selecting previously deselected package mysql-server. Unpacking mysql-server (from .../mysql-server_5.0.51a-24+lenny5_all.deb) ... Processing triggers for man-db ... Setting up mysql-server-5.0 (5.0.51a-24+lenny5) ... Stopping MySQL database server: mysqld. /var/lib/dpkg/info/mysql-server-5.0.postinst: line 144: /etc/mysql/conf.d/old_passwords.cnf: No such file or directory dpkg: error processing mysql-server-5.0 (--configure): subprocess post-installation script returned error exit status 1 Setting up mysql-client (5.0.51a-24+lenny5) ... dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.0; however: Package mysql-server-5.0 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: mysql-server-5.0 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) Now I can't seem to figure out what to do. I just want to get a clean MySQL installation at this point. I'm running the latest stable release of Debian. All help is appreciated—thanks! Edit: I looked at this similar question, which suggests that I uninstall mysql-common, but when I try to do so I see: The following packages will be REMOVED: apache2 apache2-mpm-prefork apache2-utils apache2.2-common git-svn libapache2-mod-php5 libapache2-mod-python libapache2-svn libaprutil1 libdbd-mysql-perl libdbd-mysql-rubygem libmysql-ruby libmysql-ruby1.8 libmysql-rubygem libmysqlclient15-dev libmysqlclient15off librdf-perl librdf0 libserf-0-0 libsvn-perl libsvn1 mysql-client-5.0 mysql-common mytop ndn-apache22-php5 ndn-apache22-svn ndn-interpreters ndn-lighttpd ndn-netsaint-plugins ndn-perl-modules ndn-php5-cgi ndn-php5-xcache ndn-php53 ndn-php53-suhosin ndn-rubygems php5 php5-mcrypt php5-mysql proftpd proftpd-mod-mysql python-django python-mysqldb python-subversion python-svn subversion subversion-tools trac zendoptimizer 0 upgraded, 0 newly installed, 48 to remove and 1 not upgraded. Eeek! Any suggestions?

  Read the article

• Event 36888 : The following fatal alert was generated: 10. The internal error state is 1203

  - by Param

  I search on the Internet, but i am unable to find, Why this error is coming? It has flooded my Event Viewer, after interval of 1 minutes, this Error pops-up. ( means the frequency is 1 minutes ) I didn't have any IIS installed. This server is purely Domain controller and no other role has been added. Please suggest, what should i do? Server OS - Window Server 2008 R2 Standard Edition More detail:- Log Name: System Source: Schannel Date: 6/28/2012 6:06:11 PM Event ID: 36888 Task Category: None Level: Error Keywords: User: SYSTEM Computer: QKSRVDC212.Corp.abc.com Description: The following fatal alert was generated: 10. The internal error state is 1203. Event Xml: 36888 0 2 0 0 0x8000000000000000 9305 System QKSRVDC212.Corp.abc.com 10 1203 Thanks & Regards, Param

  Read the article

• Cloudera Manager agent deploy failing to receive heartbeat from agent

  - by user150341

  All, I am getting the error on the console at the last phase of the installation: Installation failed. Failed to receive heartbeat from agent Server Log: 2012-12-19 00:32:12,132 INFO [NodeConfiguratorThread-4- 0:node.NodeConfiguratorProgress@503] 192.168.1.100: Setting WAIT_FOR_HEARTBEAT as failed and done state All nodes (name node and (2)client nodes) are VM's running 64bit CentOS. sshd has been enabled on all nodes, and VM's are set to Bridge. Any clue on how to fix this error?

  Read the article

• Why am I getting warnings about missing DLLs when adding a node to a WSFC?

  - by Stuart Branham

  We're getting the following two errors when adding a node to our WSFC. The node was added successfully, but the 'SQL Server Availability Group' resource type could not be installed on it. Unable to find 'hadrres.dll' on any of the cluster nodes. The node was added successfully, but the 'SQL Server FILESTREAM Share' resource type could not be installed on it. Unable to find 'fssres.dll' on any of the cluster nodes. This cluster is going to host an AlwaysOn Availability Group. SQL Server 2012 is installed on both nodes, and availability groups are enabled on both. Filestream access is also configured on both. Another curious thing I'm seeing is that my instance on the second node doesn't appear in Configuration Manager. Anyone know what may be going on here?

  Read the article

• Web server connection to SQL Server: Response Packet [Malformed Packet]

  - by John Murdoch

  I am seeing very, very sluggish performance between my web server (which handles HTTP web services connections) and a separate server running Microsoft SQL Server 2008. I have been capturing packet traffic on the web server trying to understand why things are running so slowly. I am using Wireshark to capture the packet traffic. The apparent problem is that the web server is sending TDS packets to the data server--each packet followed by a response from the data server with Response Packet [Malformed Packet] in the Info field. The packet sent from the web server appears to have an invalid checksum. Has anyone seen this type of problem before? Any ideas?

  Read the article

• VMWare ESXi, change the default path for a VM

  - by glenatron

  For some reason VMWare ESXi has decided that one of my VMs is on a completely different path to the path it is actually on. So my VM is on /vmfs/volumes/long-guid-here/my-vm-name but when I try to open it I get the message "File < unspecified filename was not found." Which is not really surprising as unspecified filenames are quite difficult to locate. I thought it was just the swap file, which was down in the .vmx file as /vmfs/volumes/long-guid-here/old-vm-name/old-vm-name.vmsd but when I changed that in the vmx it made no difference. What I can't figure out is where VMWare is getting the old-vm-name from- when I look in the "Settings" pane it believes the working file location to be "[datastore-name] old-vm-name\" and I can't find anywhere to change it. Now the files themselves are all named for old-vm-name - so the directory is /my-vm-name/old-vm-name.vmx and so on. Is this the cause of my problems or is there some arcane configuration option elsewhere around the VMWare machine that I need to be tinkering with?

  Read the article

• l2tp / ipsec debian Openswan U2.6.38 does not connect

  - by locojay

  i am trying to get ipsec/l2tp running on a debian server with an iphone as a client but always get: Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [RFC 3947] method set to=115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike] meth=114, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-08] meth=113, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-07] meth=112, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-06] meth=111, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-05] meth=110, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-04] meth=109, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] meth=108, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02] meth=107, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 115 Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: ignoring Vendor ID payload [FRAGMENTATION 80000000] Dec 2 21:00:04 vpn pluto[22711]: packet from <clientip>:43598: received Vendor ID payload [Dead Peer Detection] Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: responding to Main Mode from unknown peer <clientip> Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R1: sent MR1, expecting MI2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike (MacOS X): both are NATed Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: STATE_MAIN_R2: sent MR2, expecting MI3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: ignoring informational payload, type IPSEC_INITIAL_CONTACT msgid=00000000 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: Main mode peer ID is ID_IPV4_ADDR: '10.2.210.176' Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[4] <clientip> #20: switched from "L2TP-PSK-noNAT" to "L2TP-PSK-noNAT" Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: new NAT mapping for #20, was <clientip>:43598, now <clientip>:49826 Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_256 prf=oakley_sha group=modp1024} Dec 2 21:00:04 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: the peer proposed: <public ip>/32:17/1701 -> 10.2.210.176/32:17/0 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: NAT-Traversal: received 2 NAT-OA. using first, ignoring others Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: responding to Quick Mode proposal {msgid:311d3282} Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: us: 171.138.2.13<171.138.2.13>:17/1701 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: them: <clientip>[10.2.210.176]:17/61719 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: Dead Peer Detection (RFC 3706): enabled Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: transition from state STATE_QUICK_R1 to state STATE_QUICK_R2 Dec 2 21:00:05 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #21: STATE_QUICK_R2: IPsec SA established transport mode {ESP=>0x05e23c9a <0x216077a9 xfrm=AES_256-HMAC_SHA1 NATOA=10.2.210.176 NATD=<clientip>:49826 DPD=enabled} Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA(0x05e23c9a) payload: deleting IPSEC State #21 Dec 2 21:00:26 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip> #20: received Delete SA payload: deleting ISAKMP State #20 Dec 2 21:00:27 vpn pluto[22711]: "L2TP-PSK-noNAT"[5] <clientip>: deleting connection "L2TP-PSK-noNAT" instance with peer <clientip> {isakmp=#0/ipsec=#0} Dec 2 21:00:27 vpn pluto[22711]: packet from <clientip>:49826: received and ignored informational message Dec 2 21:00:27 vpn pluto[22711]: ERROR: asynchronous network error report on eth0 (sport=4500) for message to <clientip> port 49826, complainant <clientip>: Connection refused [errno 111, origin ICMP type 3 code 3 (not authenticated)] my setup looks like this verizon fios actiontec -- DMZ-- ddwrt router -- debian xen instance actiontec : 192.168.1.1 ddwrt: 171.138.2.1 debian xen server: 171.138.2.13 forwarded udp 500, 4500, 1701 on ddwrt to debian xen instance. vpn passthrough is enabled /etc/ipsec.conf config setup dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12,%v4:25.0.0.0/8,%v6:fd00::/8,%v6:fe80::/10,%v4:!171.138.2.0/24,%v4:!192.168.1.0/24 protostack=netkey # Add connections here conn L2TP-PSK-NAT rightsubnet=vhost:%priv also=L2TP-PSK-noNAT conn L2TP-PSK-noNAT authby=secret pfs=no auto=add keyingtries=3 # we cannot rekey for %any, let client rekey rekey=no # Apple iOS doesn't send delete notify so we need dead peer detection # to detect vanishing clients dpddelay=30 dpdtimeout=120 dpdaction=clear # Set ikelifetime and keylife to same defaults windows has ikelifetime=8h keylife=1h # l2tp-over-ipsec is transport mode type=transport # left=171.138.2.13 # # For updated Windows 2000/XP clients, # to support old clients as well, use leftprotoport=17/%any leftprotoport=17/1701 # # The remote user. # right=%any # Using the magic port of "%any" means "any one single port". This is # a work around required for Apple OSX clients that use a randomly # high port. rightprotoport=17/%any #force all to be nat'ed. because of ios conn passthrough-for-non-l2tp type=passthrough left=171.138.2.13 leftnexthop=171.138.2.1 right=0.0.0.0 rightsubnet=0.0.0.0/0 auto=route /etc/xl2tp/xl2tp.conf [global] ipsec saref = no listen-addr = 171.138.2.13 ;port = 1701 ;debug network = yes ;debug tunnel = yes ;debug network = yes ;debug packet = yes [lns default] ip range = 171.138.2.231-171.138.2.239 local ip = 171.138.2.13 assign ip = yes require chap = no refuse pap = no require authentication = no ;name = OpenswanVPN ppp debug = yes pppoptfile = /etc/ppp/options.xlt2tpd lenght bit = yes /etc/ppp/options.xl2tpd ;require-mschap-v2 pcp-accept-local ipcp-accept-local ipcp-accept-remote ;ms-dns 171.138.2.1 ms-dns 192.168.1.1 ms-dns 8.8.8.8 name l2tpd noccp auth crtscts idle 1800 mtu 1410 mru 1410 lock proxyarp connect-delay 5000 debug dump logfd 2 logfile /var/log/xl2tpd.log ipsec verify Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.38/K3.0.0-1-amd64 (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [FAILED] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] The failed can be ignored i guess since cat /proc/sys/net/ipv4/ip_forward returns 1 any help would be much appreciated as i don't have any idea why this is not working

  Read the article

• Task scheduler "hidden" only hides task, not process

  - by Brandi

  I am trying to make an application that acts like a desktop application for all the computers in our network. I have already got a windows forms app that works like I want it to, and I'm using the task scheduler to start it on login. We would really like it if the process as well as the task is hidden from the task manager in order to avoid accidental deletion. Selecting "Hidden" in the task scheduler hides the task (good!) but the process is still visible (not good enough). I tried using the option to run as "SYSTEM" or "LOCAL SERVICE" so that the user would get "access denied" when trying to delete or just wouldn't even view it by default. However, running as a service makes the process invisible on Vista and 7, and the point of my app is to display information interactively. (User can click, sort, etc). Is there any other alternatives to either run the process as someone/something besides the logged in user and still have the logged on user be able to see and interact with it? (Therefore it would list as someone else's app?) From what I've read on the internet, the only ways to actually hide something from the task manager seem hacky and/or difficult and rather involved. I don't really want to write a bunch of C or whatever only to maybe not have it work on Vista/7 anyway. Besides which, for a legitimate app with a legitimate use, I shouldn't have to go to those extremes... I see "Access Denied" all the time for system processes... why is it so hard for me to do the same? So does anyone have any simple solutions? Is it easier than I think to just list something in the task manager as another user? Thanks in advance for any replies.

  Read the article

• Programmatically add an ISAPI extension dll in IIS 7 using ADSI?

  - by fretje

  I apologize beforehand, this is a cross post of this SO question. I thought I'd ask it there first, but apparently it doesn't harvest any answers there. I hope it will get more attention here. When I have an answer somewhere, I'll delete the other one. I'm trying to programmatically add an ISAPI extension dll in IIS using ADSI. This has been working for ages on previous versions of IIS, but it seems to fail on IIS 7. I am using similar code like shown in this question: var web = GetObject("IIS://localhost/W3SVC/1/ROOT/specificVirtualDirectory"); var maps = web.ScriptMaps.toArray(); map[maps.length] = ".aaa,c:\\path\\to\\isapi\\extension.dll,1,GET,POST"; web.ScriptMaps = maps.asDictionary(); web.SetInfo(); After executing that code, I do see an "AboMapperCustom-12345678" entry for that specific dll in the "Handler mappings" of the specific virtual directory in which I added the script map. But when I try to use that extension in a browser, I always get HTTP Error 404.2 Not Found The page you are requesting cannot be served because of the ISAPI and CGI Restriction list settings on the Web server. Even after adding an entry to allow that specific dll in the "ISAPI and CGI restrictions", I keep getting that error. To make it actually work, I first have to undo these steps (encountering the same issue like the OP of the question mentioned above: after deleting the script map entry from the IIS manager GUI, I also have to programmatically delete it using ADSI before it's actually gone from the metabase). And then manually add an entry like this: inetmgr - webserver - website - virtual directory - handler mappings - add script map... path = *.dll, executable = <path to dll>, name = <doesn't matter, but it's mandatory> click "yes" on the question "do you want to allow this ISAPI extension?" When I compare the 2 entries, they are exactly the same, except for the "Entry Type" which seems to be "Inherited" for the programmatically added one and "Local" for the one added manually. The strange thing is, even though it says "Inherited", I don't see it anywhere in IIS on a higher level. Where is it inheriting from? In my code, I do add the script map to the specific virtual directory so it should be "Local" as well. Maybe there is the problem, but I don't know how to add a "Local" Script Map using ADSI. I really would like to keep using the ADSI method, as otherwise I will have to use different methods in our setup when working with IIS 7 or previous versions, and I would like to avoid that. To recap: How can I programmatically add a script map entry and its companion CGI and ISAPI restrictions entry to IIS 7 using ADSI? Anybody who can shed some light on this? Any help appreciated.

  Read the article

• Broadcom NIC Teaming w/ 802.3ad and Dell Powerconnect 2824

  - by Carltoncl

  We have a Poweredge R210 running WS2K8R2. The server has two Broadcom 5716C NICs running Broadcom BASP. I can team the NICs using the 802.3ad protocol on the server end no problem. I have no VLAN. Now I go to the 2824 switch (default settings all round) running in managed mode and create a LAG with ports g1 and g2. As soon as I add these ports, I lose the ability to send traffic to or from the server. I am much more of a server guy than a networking guy, what am I doing wrong here? Server Static IP Address: 10.10.61.15 Network mask: 255.255.255.0 Gateway: 10.10.61.51 The 2824 switch has an IP address of 10.10.61.51 and in turn has its gateway as our firewall server running ISA Server at 10.10.61.50.

  Read the article

• SSL Certificate error: verify error:num=20:unable to get local issuer certificate

  - by Brian

  I've been trying to get an SSL connection to an LDAPS server (Active Directory) to work, but keep having problems. I tried using this: openssl s_client -connect the.server.edu:3269 With the following result: verify error:num=20:unable to get local issuer certificate I thought, OK, well server's an old production server a few years old. Maybe the CA isn't present. I then pulled the certificate from the output into a pem file and tried: openssl s_client -CAfile mycert.pem -connect the.server.edu:3269 And that didn't work either. What am I missing? Shouldn't that ALWAYS work?

  Read the article

• Windows 7 Desktop/Start Menu Redirection: Server O/S: Windows Server 2003 And Server 2008

  - by Moody Tech

  Hi, I am new here so I am might be asking a question which has already been answered [however I can't see it in the suggested answers above] I manage a network which is split into a parent domain and a child domain. Recently I have been looking at when to migrate to Windows 7. The child domain users [authenticated by the 2008 based (child) domain] get the redirected Desktop [as expected] but not the Start Menu. The parent domain users [authenticated by the 2003 based (parent) domain] get neither desktop nor Start Menu redirected. Does anyone here know how to successfully redirect the properties for these users as desired? Many thanks.

  Read the article

• Netem on Windows??

  - by hassan assi

  i want to use a Network emulator but in windows environment does Netem works their ?? if not any alternatives ? thanks Hassan Assi

  Read the article

• SQL Server: How to shrink FileStream files?

  - by J4N

  For a project, I'm using a SQL Server 2008 R2. One table has a filestream column. I've made some load tests, and now the database has ~20GB used. I've empty tables, except several(configuration tables). But my database was still using a lot of space. So I used the Task -> Shrink -> Database / Files But my database is still using something like 16GB. I found that it's the filestream file is still using a lot of space. The problem is that I need to backup this database to export it on the final production server, and event if I indicate to compress the backup I got a file more than 3.5Go. Not convenient to store and upload. And I'm planning much bigger test, so I want to know how to shrink that empty space. When I'm trying: I get this exception: The properties SIZE, MAXSIZE, or FILEGROWTH cannot be specified for the FILESTREAM data file 'FileStreamFile'. (Microsoft SQL Server, Error: 5509) So what should I do? I found several topics with this error but they was about removing the filestream column.

  Read the article

• How to fix Solr - Server is shutting down issue?

  - by Krunal

  I was having a running Solr 4.1 on Windows Server 2008 R2. The Solr is deployed on Tomcat. However, today it stops suddenly, and while accessing Solr it gives following error. HTTP Status 503 - Server is shutting down type Status report message Server is shutting down description The requested service is not currently available. On further looking into Logs, we got following: Log File: tomcat7-stderr.2013-05-09.txt May 09, 2013 8:00:40 PM org.apache.solr.core.CoreContainer finalize SEVERE: CoreContainer was not shutdown prior to finalize(), indicates a bug -- POSSIBLE RESOURCE LEAK!!! instance=2221663 Log File: catalina.2013-05-09.txt May 09, 2013 7:59:25 PM org.apache.solr.core.SolrResourceLoader <init> INFO: new SolrResourceLoader for directory: 'c:\solrdir\' May 09, 2013 7:59:29 PM org.apache.solr.common.SolrException log SEVERE: Exception during parsing file: null:org.xml.sax.SAXParseException; systemId: file:/c:/solr/solr.xml; lineNumber: 2; columnNumber: 6; The processing instruction target matching "[xX][mM][lL]" is not allowed. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(Unknown Source) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.scanPIData(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanPIData(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.scanPI(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl$PrologDriver.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.DOMParser.parse(Unknown Source) at com.sun.org.apache.xerces.internal.jaxp.DocumentBuilderImpl.parse(Unknown Source) at org.apache.solr.core.Config.<init>(Config.java:121) at org.apache.solr.core.CoreContainer.load(CoreContainer.java:428) at org.apache.solr.core.CoreContainer.load(CoreContainer.java:404) at org.apache.solr.core.CoreContainer$Initializer.initialize(CoreContainer.java:336) at org.apache.solr.servlet.SolrDispatchFilter.init(SolrDispatchFilter.java:98) at org.apache.catalina.core.ApplicationFilterConfig.initFilter(ApplicationFilterConfig.java:281) at org.apache.catalina.core.ApplicationFilterConfig.getFilter(ApplicationFilterConfig.java:262) at org.apache.catalina.core.ApplicationFilterConfig.<init>(ApplicationFilterConfig.java:107) at org.apache.catalina.core.StandardContext.filterStart(StandardContext.java:4656) at org.apache.catalina.core.StandardContext.startInternal(StandardContext.java:5309) at org.apache.catalina.util.LifecycleBase.start(LifecycleBase.java:150) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:901) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:877) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:633) at org.apache.catalina.startup.HostConfig.deployWAR(HostConfig.java:977) at org.apache.catalina.startup.HostConfig$DeployWar.run(HostConfig.java:1655) at java.util.concurrent.Executors$RunnableAdapter.call(Unknown Source) at java.util.concurrent.FutureTask$Sync.innerRun(Unknown Source) at java.util.concurrent.FutureTask.run(Unknown Source) at java.util.concurrent.ThreadPoolExecutor.runWorker(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source) at java.lang.Thread.run(Unknown Source) May 09, 2013 7:59:29 PM org.apache.solr.servlet.SolrDispatchFilter init SEVERE: Could not start Solr. Check solr/home property and the logs May 09, 2013 7:59:29 PM org.apache.solr.common.SolrException log SEVERE: null:org.apache.solr.common.SolrException: at org.apache.solr.core.CoreContainer.load(CoreContainer.java:431) at org.apache.solr.core.CoreContainer.load(CoreContainer.java:404) at org.apache.solr.core.CoreContainer$Initializer.initialize(CoreContainer.java:336) at org.apache.solr.servlet.SolrDispatchFilter.init(SolrDispatchFilter.java:98) at org.apache.catalina.core.ApplicationFilterConfig.initFilter(ApplicationFilterConfig.java:281) at org.apache.catalina.core.ApplicationFilterConfig.getFilter(ApplicationFilterConfig.java:262) at org.apache.catalina.core.ApplicationFilterConfig.<init>(ApplicationFilterConfig.java:107) at org.apache.catalina.core.StandardContext.filterStart(StandardContext.java:4656) at org.apache.catalina.core.StandardContext.startInternal(StandardContext.java:5309) at org.apache.catalina.util.LifecycleBase.start(LifecycleBase.java:150) at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:901) at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:877) at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:633) at org.apache.catalina.startup.HostConfig.deployWAR(HostConfig.java:977) at org.apache.catalina.startup.HostConfig$DeployWar.run(HostConfig.java:1655) at java.util.concurrent.Executors$RunnableAdapter.call(Unknown Source) at java.util.concurrent.FutureTask$Sync.innerRun(Unknown Source) at java.util.concurrent.FutureTask.run(Unknown Source) at java.util.concurrent.ThreadPoolExecutor.runWorker(Unknown Source) at java.util.concurrent.ThreadPoolExecutor$Worker.run(Unknown Source) at java.lang.Thread.run(Unknown Source) Caused by: org.xml.sax.SAXParseException; systemId: file:/c:/solrdir/solr.xml; lineNumber: 2; columnNumber: 6; The processing instruction target matching "[xX][mM][lL]" is not allowed. at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.createSAXParseException(Unknown Source) at com.sun.org.apache.xerces.internal.util.ErrorHandlerWrapper.fatalError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLErrorReporter.reportError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.reportFatalError(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.scanPIData(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanPIData(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLScanner.scanPI(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl$PrologDriver.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentScannerImpl.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLNSDocumentScannerImpl.next(Unknown Source) at com.sun.org.apache.xerces.internal.impl.XMLDocumentFragmentScannerImpl.scanDocument(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XML11Configuration.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.XMLParser.parse(Unknown Source) at com.sun.org.apache.xerces.internal.parsers.DOMParser.parse(Unknown Source) at com.sun.org.apache.xerces.internal.jaxp.DocumentBuilderImpl.parse(Unknown Source) at org.apache.solr.core.Config.<init>(Config.java:121) at org.apache.solr.core.CoreContainer.load(CoreContainer.java:428) ... 20 more May 09, 2013 7:59:29 PM org.apache.solr.servlet.SolrDispatchFilter init INFO: SolrDispatchFilter.init() done May 09, 2013 7:59:29 PM org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory C:\Program Files (x86)\Apache Software Foundation\Tomcat 7.0\webapps\docs May 09, 2013 7:59:30 PM org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory C:\Program Files (x86)\Apache Software Foundation\Tomcat 7.0\webapps\manager May 09, 2013 7:59:30 PM org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory C:\Program Files (x86)\Apache Software Foundation\Tomcat 7.0\webapps\ROOT May 09, 2013 7:59:30 PM org.apache.coyote.AbstractProtocol start INFO: Starting ProtocolHandler ["http-bio-8983"] May 09, 2013 7:59:30 PM org.apache.coyote.AbstractProtocol start INFO: Starting ProtocolHandler ["ajp-bio-8009"] May 09, 2013 7:59:30 PM org.apache.catalina.startup.Catalina start INFO: Server startup in 9578 ms May 09, 2013 8:00:40 PM org.apache.solr.core.CoreContainer finalize SEVERE: CoreContainer was not shutdown prior to finalize(), indicates a bug -- POSSIBLE RESOURCE LEAK!!! instance=2221663 Any idea what could be wrong and how to fix?

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >