Search Results

Search found 18096 results on 724 pages for 'order numbering'.

Page 521/724 | < Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >

  • Data recovery on a corrupted 3TB disk

    - by Mark K Cowan
    Short version I probably need software to run a deep-scan recovery (ideally on Linux) to find files on NTFS filesystem. The file data is intact, but the references are no longer present. Analogous to recovering data from a "quick-formatted" partition. Hopefully there is a smarter way available than deep-scan, one which would recover filenames and possibly paths. Long version I have a 3TB disk containing a load of backups. Windows 7 SP1 refused to detect the disk when plugged in directly via SATA, so I put it on a USB/SATA adaptor which seemed to work at first. The SATA/USB adaptor probably does not support disks over 2.2TB though. Windows first asked me if I wanted to 'format' the disk, then later showed me most of the contents but some folder were inaccessible. I stupidly decided to run a CHKDSK on my backup disk, which made the folders accessible but also left them empty. I connected this disk via SATA to my main PC (Arch Linux). I tried: testdisk ntfsundelete ntfsfix --no-action (to look for diagnostically relevant faults, disk was "OK" though) to no avail as the files references in the tables had presumably been zeroed out by CHKDSK, rather than using a typical journal'd deletion). If it is useful at all, a majority of the files that I want to recover are JPEG, Photoshop PSD, and MPEG-3/MPEG-4/AVI/MKV files. If worst comes to worst, I'll just design my own sector scanner and use some simple heuristic-driven analysis to recover raw binary blocks of data from the disk which appears to match the structures of the above file types. I am unfamiliar with the exact workings of NTFS but used to be proficient at recovering FAT32 systems with just a hex-editor, so I can provide any useful diagnostic information if you let me know how to find it! My priorities in ascending order of importance for choosing the accepted answer: Restores directory structure Recovers many filenames in addition to the file data Is free / very cheap Runs on Linux Recovers a majority of file data The last point is the most important, but the more of the higher points you match the more rep you'll probably get :)

    Read the article

  • Domain registrar transfering

    - by Mike Weerasinghe
    In 2004 I registered a domain name when I opened an account with DiscountASP.NET. I presume my domain registration was handled by a reseller. A domain tools who is search shows that registration services are provided by Znode LLC. I changed hosting companies and need to change DNS servers to point to my new hosting company but I have no idea how to do that. There is no control panel I can access. Ideally I would like to transfer registrar's. I emailed Znode support but I have not received any response. I called and left a message and they have not called back. My new hosting company wants an EPP authorization code in order to transfer my domain. I guess I need to get it from Znode LLC. Anyone have any ideas on how I might go about transferring my domain over to a new registrar? The domain name has not expired and is currently active. Thanks in advance for your help.

    Read the article

  • How to create VirtualHost in Ubuntu 12.10

    - by Mifas
    I had followed many articles to 'How to create VirtualHost in Ubuntu'. This is what have I done Installed Apache sudo apt-get install lamp-server^ phpmyadmin I created folder called site1.com in /var/www/ Then I have created the file in /etc/apache2/sites-available/site1.com Then added the following code to that site1.com file <VirtualHost *:80> ServerName www.site1.com ServerAdmin [email protected] ServerAlias site1.com DocumentRoot /var/www/site1.com # Other directives here <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site1.com/> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny Allow from all </Directory> </VirtualHost> Then after that I edit the host file added the following line of code 127.0.0.1 site1.com Edit Also I enable the site1.com via sudo a2ensite site1.com Then i restart the apache serivice. (Even i restarted the pc) When I go to the site1.com, It will say The connection has timed out Error Message. But I can browse via localhost/site1.com. I have been trying since last two days. No solution. And followed many articles and videos.

    Read the article

  • How can I get WAMP and a domain name to work on a non-standard port?

    - by David Murdoch
    I have read countless articles on setting up a domain on WAMP to listen on a port other than 80; none of them are working. I've got Windows Server 2008 (Standard) with IIS 7 installed and running on port 80 (and 443). I've got WAMP installed with the following configuration. Listen 81 ServerName sub.example.com:81 DocumentRoot "C:/Path/To/www" <Directory "C:/Path/To/www"> Options All MultiViews AllowOverride All # onlineoffline tag - don't remove Order Allow,Deny Allow from all </Directory> localhost:81 works with the above configuration but sub.example.com:81 does not. Just to make sure my firewall wasn't getting in the way I have disabled it completely. My sub.example.com domain is already pointing to my server and works on IIS on port 80. Also, if I disable IIS and change the Apache port from 81 to 80 it works. Yes, I am restarting Apache after each httpd.conf change. :-) I don't need any other domain (or sub domains [I don't even care about localhost]) configured which is why I'm not using a VirtualHost. Any ideas what is going on here? What could I be doing wrong? Update Changing Listen to 80 but keeping ServerName as sub.example.com:81 causes navigation to sub.example.com:80 to work; this just doesn't seem right to me. Could ServerName be ignoring the :port part somehow? netstat -a -n | find "TCP": >netstat -a -n | find "TCP" TCP 0.0.0.0:81 0.0.0.0:0 LISTENING TCP 0.0.0.0:135 0.0.0.0:0 LISTENING TCP 0.0.0.0:445 0.0.0.0:0 LISTENING TCP 0.0.0.0:912 0.0.0.0:0 LISTENING ... TCP 127.0.0.1:81 127.0.0.1:49709 TIME_WAIT ...

    Read the article

  • Is it possible to detect nearby Wi-Fi enabled devices, not necessarily on the same network? [closed]

    - by Sky
    first question on StackExchange ever. I hope I got the right board. I'm trying to create a device (either from a standard AP or some other unconventional means) that will be able to detect nearby Wi-Fi enabled devices. For example, if a cellular phone (iPhone for instance) would be carried into the secured area, its MAC address will be logged. A cellular phone is a good example because it's the most common threat that should be detected. Some important points: The detection can be either active or passive, doesn't matter. The detected device might be connected to a different network, or might not be connected to anything at all. I assume most cellular phones are actively probing when not connected, but I'm not sure. It is important to not only identify the breach, but also to identify the device (MAC address). Conventional hardware is only optional. Distance of detection is at least 6 meters (20 feet). Handling one device at a time is good. Speed of detection is important, under 5 seconds is ideal. So my question is, is this even possible? If so, what can I use in order to make this a reality? Thank you for reading!

    Read the article

  • Registering publicly Mail server and Web server in a free dns server

    - by Bruno Vieira
    I'm trying to host the e-mails and the site of our company into our private server. I've already followed the Gentoo Virtual Mailhosting System with Postfix Guide and my mail server is working (actually it sends mails for the local users and for external users it goes to spam) and know how to set an Apache 2 server. What I don't know (and I mean really don't) is how to make them public. I did some research and found that I should ask my ISP to change the reverse DNS to my company domain in order to prevent my mails to be marked as spam, they are doing. I already know I have to configure a DNS Server, it seems like my register provider already has one but I don't know how I can configure CNET, A, MX, TXT and all those tags (Is it tags the name?) and If I must do some other configuration on my server. My Server: Linux mail 3.2.21-gentoo #1 SMP My /etc/hosts: 127.0.0.1 mail.example.com.br example example.com.br ::1 mail.example.com.br mail example.com.br My /etc/conf.d/hostname: hostname ="mail" What am I missing? If there's a guide about how to configure I would really be grate. Thanks in advance for the help. Cheers

    Read the article

  • howto configure proxy.conf for mod_proxy, apache2, jetty

    - by Kaustubh P
    Hello, This is how I have setup my environment, atm. An apache2 instance on port 80. Jetty instance on the same server, on port 8090. Use-Case: When I visit foo.com, I should see the webapp, which is hosted on jetty, port 8090. If I put foo.com/blog, I should see the wordpress blog, which is hosted on apache. (I read howtos on the web, and installed it using AMP.) Below are my various configuration files: /etc/apache2/mods-enabled/proxy.conf: ProxyPass / http://foo.com:8090/ << this is the jetty server ProxyPass /blog http://foo.com/blog ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPreserveHost On ProxyStatus On /etc/apache2/httpd.conf: LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_balancer_module /usr/lib/apache2/modules/mod_proxy_balancer.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so LoadModule proxy_ajp_module /usr/lib/apache2/modules/mod_proxy_ajp.so I have not created any other files, in sites-available or sites-enabled. Current situation: If I goto foo.com, I see the webapp. If I goto foo.com/blog, I see a HTTP ERROR 404 Problem accessing /errors/404.html. Reason: NOT_FOUND powered by jetty:// If I comment out the first ProxyPass line, then on foo.com, I only see the homepage, without CSS applied, ie, only text.. .. and going to foo.com/blog gives me a this error: The proxy server received an invalid response from an upstream server. The proxy server could not handle the request GET /blog. Reason: Error reading from remote server I also cannot access /phpmyadmin, giving the same 404 NOT_FOUND error as above. I am running Debian squeeze on an Amazon EC2 Instance. Question: Where am I going wrong? What changes should I make in the proxy.conf (or another conf files) to be able to visit the blog?

    Read the article

  • "The zone can be scavenged after" keeps incrementing

    - by kce
    What are you trying to do? I'm trying to enable DNS scavenging on a DNS zone that has about a hundred stale DNS records. What have you tried in order to make it happen? I setup DNS Scavenging per everyone's favorite TechNet Blog post: Don't be afraid of DNS Scavenging. Just be patient. I first disabled scavenging on all of our domain controllers: DNSCmd . /ZoneResetScavengeServers contoso.com 192.168.1.1 192.168.1.2 I then enabled automatic scavenging on the DNS zone: I then enabled DNS scavenging on one of the domain controllers: I then found a few records that I expected to get delete with timstamps from a few years ago and ensured that that the Delete this record when it becomes stale and that time stamp was actually set: Finally I reloaded the zone and waited 14 days (the sum of the Refresh + No-Refresh periods). What results did you expect? I expected to see a 2501 Event in the DNS server logs noting the deletion of a bunch of DNS records. What actually happened? Nothing happened. The Zone Aging/Scavenging Properties showed that the zone could be scavenged after 6/12/2014 10:00:00 AM last week. No 2501/2502 events were recorded. All of the records with "aged" time stamps are still present. The date at which the zone can be scavenged after incremented another seven days to ?6/?18/?2014 10:00:00 AM. As I understand it until that date stays at least 14 days in the past nothing will ever even be eligible for scavenging let alone actually be scavenged. The only 2501 events recorded in the event logs are ones that I have triggered by right clicking and selecting "Scavenge Stale Resource Records". They note that scavenging will try to run again in 168 hours which was this morning. I have DNS scavenging enabled for a few months and have waited patiently for something to happen. I have reloaded the zone multiple times (which resets this timestamp). What am I missing here?

    Read the article

  • Why is /usr/bin/env permission denied to rails server?

    - by Eric Hopkins
    I've just set up rails on an apache server running on Ubuntu, and when I try to go to the root page it gives this error: /usr/bin/env: bash: Permission denied env and all the directories in the path all have permissions 755. I tried setting env to have permissions 777 but still got the same error. Rails is running as "nobody". Why is this happening? I don't know what else to try. In /etc/apache2/sites-available/api.conf: <VirtualHost *:80> ServerName api.thinknation.ca ServerAlias api.thinknation.ca DocumentRoot /var/www/api/public ErrorLog /var/www/logs/error.log CustomLog /var/www/logs/access.log combined RailsSpawnMethod smart <Directory /var/www/api/public> # This relaxes Apache security settings. AllowOverride all # MultiViews must be turned off. Options -MultiViews -Indexes # Uncomment this if you're on Apache >= 2.4: Order allow,deny Allow from all #Require all granted </Directory> </VirtualHost> From config/database.yml in my rails directory (with sensitive user names and passwords omitted): default: &default adapter: mysql2 encoding: utf8 pool: 5 username: root password: socket: /var/run/mysqld/mysqld.sock development: <<: *default database: api_development test: <<: *default database: api_test production: <<: *default url: <%= ENV['DATABASE_URL'] %> database: api username: ------------ password: ------------ Not sure what other details or files are relevant, I will add them if needed.

    Read the article

  • Google Chrome not loading web pages correctly unless multiple refreshes

    - by Brandon Wilson
    Webpages in Google Chrome do not load correctly from time to time. I can't reproduce it, it just happens. Some times it happens when I load the browser other times it happens when I am just browsing. Just now I went to five different web sites which 3 out of 5 of them did not load correctly. I have attached a photo of how Super User loaded the first time I loaded it. If I refreshed it it will load correctly. Facebook is bad like this. Some times Facebook will load correctly but some of there back end scripting may not load so the page may not refresh automatically. Not sure what is going on. I have tried other browsers (Firefox and Internet Explorer) and they seem to be working correctly. Chrome seems to be acting up only on this computer. All my computers are running Windows 8 and I have removed Chrome completely off this computer and re-installed. I even disabled all extensions and cleared all the caches. I even tried running Chrome without being logged in. Not sure what else to do at this point. An example of superuser.com not loading correctly: When I refresh the problem will go away until it happens again. Sometimes it takes two or three refreshes in order for it to correctly load.

    Read the article

  • How can I set Thunderbird's "Recipient" column to display my email address rather than a friendly na

    - by Howiecamp
    After configuring a single, unified Inbox within Outlook 2007 to unify multiple email accounts, I found Thunderbird 3's Smart Folder feature. It works great, providing individual inboxes for each of your email accounts and a unified inbox which provides a unified, virtual view of those other inboxes. Thunderbird is smart enough so what when I reply to an email addressed to a specific email account, the reply is "From" that email address. In order to know which inbound email was to which of my accounts, I added the "Recipient" column to the inbox Smart Folder: What's displayed in the Recipient column depends on how the sender/sender's email client addresses the email. If they send it to just "[email protected]" without specifying a friendly name, the Recipient column displays "[email protected]" and there's no ambiguity about which account the email was sent to. However, if the sender has me in their address book (likely stored with a friendly name), it will be addressed as "Howard Camp [[email protected]]" and then show in the Recipient column as "Howard Camp". The problem is that if someone emails me with a friendly name at another of my email accounts (e.g. "Howard Camp [[email protected]]", the Recipient column will also display "Howard Camp" and I can't tell which account it's to until I open the message and/or look at the details. How can I configure Thunderbird to always display my email address rather than the sender-specified friendly name in the Recipient column?

    Read the article

  • Elevating UAC via .bat file?

    - by jslaker
    Pretty straightforward one that I'm having trouble finding an answer to. serverfault previously helped me with finding a way to automate Windows updates without using WSUS. It's working fantastically, but to run it over the network, you have to first mount a shared drive. That's pretty simple XP since you just mount the drive and run the updater. On Vista and W7, though, this all has to be done with elevated privileges to work correctly. The UAC account can't see network drives mounted by the regular user, so in order to get everything working, I have to mount the share via net use from an escalated shell. I'd like to automate mounting this share and launching the updater via a simple .bat file. I could probably just instruct everybody to right click "Run as Administrator" on the .bat file, but I'd like to keep things as simple as possible and have the .bat automatically prompt the user to escalate their privileges. Since these computers don't belong to us, I can't count on anything like Powershell being installed, so that rules any solution along those lines out and pretty much have to rely on things that would be included in an RTM Vista install. I'm hoping I'm mostly missing something obvious here. :)

    Read the article

  • Managing a test iSCSI target server

    - by dyasny
    Hi all, I am using a RHEL server with a few hard drives, and tgtd as the iscsi target software. I a looking for a way to allocate and deallocate space and targets with that space, without restarting my system, or harming other LUNs. Currently, all my HDDs are PVs in a single VG, and I lvcreate/lvremove as required, and then export the allocated LVs using a tgt script: usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=1 --targetname iqn.2001-04.com.lab.gss:300gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 1 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_300Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 1 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=2 --targetname iqn.2001-04.com.lab.gss:200gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 2 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_200Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 2 -I ALL /usr/sbin/tgtadm --lld iscsi --op new --mode target --tid=3 --targetname iqn.2001-04.com.lab.gss:100gb /usr/sbin/tgtadm --lld iscsi --op new --mode logicalunit --tid 3 --lun 1 -b /dev/mapper/iscsi_vg-iscsi_100Gb /usr/sbin/tgtadm --lld iscsi --op bind --mode target --tid 3 -I ALL tgtadm --mode target --op show So in order to remove a LUN, I stop the tgtd service, lvremove the lv, and remove the entry from the iscsi target script When I add a lun, I run lvcreate, and then add an entry to the script and run it. This is not quite optimal, since restarting the service is a bad idea while other LUNs are busy, so I am looking for a more scalable and safer way. Thanks

    Read the article

  • Providing access to a Samba server for VPN clients

    - by Kamil Kisiel
    We have some Windows users that connect to our network via VPN from home. They need to be able to connect to our Samba server and access a mapped network drive just as they do as when they are on our LAN. The complication is that VPN clients are placed on a subnet other than our office LAN, and behind a firewall. What's the easiest way for me to allow them to still connect to the network share? The solutions I've currently seen involve setting up a WINS server for name resolution purposes and then tunnelling a bunch of the NetBIOS stuff through the firewall. However that means I'd have to set up the VPN DHCP server to hand out the WINS address, something I'm not even sure is possible on the Cisco hardware we have. I'm thinking there must be an easier way. Should I use an LMHOSTS file? Or just map by IP address? Also, I'm not terribly familiar with Windows networking, so which ports would I need to pass through my firewall in order to get the file sharing through?

    Read the article

  • Is it possible to re-cab an Administrative Install Point?

    - by Nathaniel Bannister
    We have Acrobat 8 Pro at work, and our media was painfully out of date. Rather than install all of the machines at 8.0.0 and then do the 6 or 7 consecutive reboots adobe expects you to be ok with I decided I'd integrate the .msp files into the installer. After reading up on it, I figured out the exact patch order that adobe required, extracted my cd to an Administrative install point, and ran the patches against it: msiexec /a AcroPro.msi /p AcrobatUpd810_efgj_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd811_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd812_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd813_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd816_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd817_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd820_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd822_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd823_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd825_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" msiexec /a AcroPro.msi /p AcrobatUpd826_all_incr.msp TARGETDIR="C:\Acrobat8" /log "output.log" Now I have a AIP that is fully patched to 8.2.6 (Tested working prior to attempting to CAB it), but is absolutely huge (1.2gb) what I would like to do is take the folders within the AIP and put them back into a cab file for the sake of convenience in transferring the files around. I tried the command: cscript "C:\Program Files\Microsoft SDKs\Windows\v7.0\Samples\sysmgmt\msi\scripts\WiMakCab.vbs" AcroPro.msi Data1 /L /C /S Per the guide I was using, while this did produce the cab file I Wanted, however the resulting MSI fails to install with an error 2602: It's been a while since I've done something like this, and it's probably a glaring oversight on my part, but any insight would be much appreciated.

    Read the article

  • Proper 16:9 video size for non-HD 4:3 video (for youtube/vimeo)

    - by Xeoncross
    Since High Definition video came out on all the online sites it has changed the default aspect ratio of the player from 4:3 to 16:9. This means that for people posting SD video you have to resize some of your videos to get them to fit right. For example, NTSC DVD quality (aka 480i/p) is 720x480 pixels (width x height). However, low-end High Definition (720i/p) is 1280x720. Resolution Chart Anyway, now that the video players are built for HD you will find that uploading standard quality videos will result in videos that are "letter boxed" which means they have extra black bars on the top and bottom (or sides). Correct me if I'm wrong, but in order to get a 720x480 video to fit a box that is designed for HD the best practice would be to crop some of it off so that it fits as 720x404 since: 16/9 = 1.78 (1.7777777777778) 720/405 = 1.78 405x1.78 = 720.9 The same would stand for 640x480 (old TV quality) video that would need to be 640x360 correct? I'm asking because I'm not sure about all this and whether this is the proper way to fix these letter-boxing/display problems.

    Read the article

  • What is causing apache2 proxy error when forwarding to tomcat?

    - by Dark Star1
    I set up apache to proxy for tomcat but I am getting the following error when I target the page. I sometimes get a blank page or a 503: [Error] [Mon Dec 03 04:58:16 2012] [error] proxy: ap_get_scoreboard_lb(2) failed in child 29611 for worker proxy:reverse [Mon Dec 03 04:58:16 2012] [error] proxy: ap_get_scoreboard_lb(1) failed in child 29611 for worker https://localhost:8443/ [Mon Dec 03 04:58:16 2012] [error] proxy: ap_get_scoreboard_lb(0) failed in child 29611 for worker http://localhost:8080/ I have two vhosts configured on the vm as follows: [http host] <VirtualHost *:80> ServerName www.mysite.net ServerAlias mysite.net ProxyRequests Off ProxyPreserveHost On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyPass / http://localhost:8080/ retry=0 ProxyPassReverse / http://localhost:8080/ retry=0 </VirtualHost> [ssl vhost] <VirtualHost *:443> ServerName www.mysite.net ServerAlias mysite.net ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On SSLEngine on SSLProxyEngine on SSLCertificateFile /etc/apache2/ssl/server.crt SSLCertificateKeyFile /etc/apache2/ssl/server.key ProxyRequests Off ProxyPreserveHost On ProxyPass / https://localhost:8443/ retry=0 ProxyPassReverse / https://localhost:8443/ retry=0 </VirtualHost> My system details are: Apache/2.2.22 (Ubuntu) mod_jk/1.2.32 mod_ssl/2.2.22 OpenSSL/1.0.1 mod proxy_http is also enabled.

    Read the article

  • Can't include Javascript variable in PHP mysql_query call? [on hold]

    - by user198895
    I want the PHP mysql_query call to retrieve user values based on the Agency drop-down value but I can't get this to work. Am I unable to include the Javascript variable agency.value in PHP? <script type="text/javascript"> var agency = document.getElementById("agency"); var user = document.getElementById("user"); agency.onchange = onchange; // change options when agency is changed function onchange() { <?php include 'dbConnect.php'; ?> <?php $q = mysql_query("select id as UserID, CONCAT(LastName, ', ' , FirstName) as UserName from users where Agency = " . ?>agency.value<?php . " order by UserName");?> option_html = "<option value=0 selected>- All Users -</option>"; <?php while ($row1 = mysql_fetch_array($q)) {?> if (agency.value == 0 || agency.value == '<?php echo $row1[AgencyID]; ?>') { option_html += "<option value=<?php echo $row1[UserID]; ?>><?php echo $row1[UserName]; ?></option>"; } <?php } ?> user.innerHTML = option_html; } </script>

    Read the article

  • Web SMTP Server(foo.com) will not send mail to exchange server which is also(foo.com)

    - by Atom
    I think I understand this problem fully, but I do not know how to approach it or where to go in terms of troubleshooting. I've got my one domain http://foo.com that runs a Zen Cart installation that needs to be able to send emails to users(order confirmation, password reset). This works fine to send to any other domain BUT foo.com. I'm running a locally hosted exchange server that is foo.com, and we can send and receive email just fine. If I run tail -f /usr/local/psa/var/log/maillog I recieve this error: Apr 1 10:08:51 foo qmail-local-handlers[25824]: Handlers Filter before-local for qmail started ... Apr 1 10:08:51 foo qmail-local-handlers[25824]: from= Apr 1 10:08:51 foo qmail-local-handlers[25824]: [email protected] Apr 1 10:08:51 foo qmail-local-handlers[25824]: cannot reinject message to '[email protected]' Apr 1 10:08:51 foo qmail: 1270141731.583139 delivery 32410: failure: This_address_no_longer_accepts_mail./ Apr 1 10:08:51 foo qmail: 1270141731.584098 status: local 0/10 remote 0/20 I understand that the foo.com SMTP service doesn't have any account but the one that is used to authenticate mail being sent, so of course, I understand why it's saying 'this address no longer accepts mail'. My question is, how can I get the foo.com(web) SMTP service to handle emails meant for my exchange server([email protected]) or how do I handle the mail that needs to be sent to our exchange server? Is this something to do with MX records? Thanks in advance A

    Read the article

  • mpirun -np N, what if N is larger than my core number?

    - by Daniel
    Say I have a 4-core workstation, what would linux (Ubuntu) do if I execute mpirun -np 9 XXX Q1. Will 9 run immediately together, or they will run 4 after 4? Q2. I suppose that using 9 is not good, because the remainder 1, it will make the computer confused, (I don't know is it going to be confused at all, or the "head" of the computer will decide which core among the 4 cores will be used?) Or it will be randomly picked. Who decide which one core to call? Q3. If I feel my cpu is not bad and my ram is okay and large enough, and my case is not very big. Is it a good idea in order to fully use my cpu and ram, that I do mpirun -np 8 XXX, or even mpirun -np 12 XXX. Q4. Who decides all of these effciency optimization, Ubuntu, or linux, or motherboard or cpu? Your enlightenment would be really appreciated.

    Read the article

  • How do I prevent or override a group policy on Windows 7?

    - by Kevin
    A few months ago my company was purchased by a large corporation. We recently switched our network over to the large corporate network which has more restrictions requirements. One of these is the requirement to use a proxy server for Internet traffic. However, some of our internal servers are not recognized by the corporate DNS, so we need to provide the fully qualified domain name. For W7, we make changes to the Internet Properties for IE8 and Chrome to include our domain name as an exception to the proxy server (e.g., *.foobar.com). The problem is that a group policy that does not include our domain name is continually pushed out to my systems throughout the day. This requires me to make the appropriate changes to the Internet Properties several times a day in order to access our internal servers. Is there a way that I can prevent the group policy from being pushed to my systems or detect when the group policy is pushed and override it? I am an administrator on all of my systems. I do have Firefox installed which is not subject to the same group policy push, but I need to have IE8 and Chrome working.

    Read the article

  • Is there a small business router that shows bandwidth usage graphs in the admin panel?

    - by Robert Drake
    I support a large number of public libraries that are having their networks upgraded in response to a grant application. These libraries are generally home to between 6-15 computers and have little or no tech services either onsite or contracted remotely. In order to justify current and future purchases, a number of the libraries have requested routers that can provide bandwidth usage graphs that they can show to their managing boards. Is there a small business router that displays traffic graphs in the router administration web interface? The router needs to suppport DHCP and basic firewalling. No other features are required. Further, the reports just need to show overall trends. It is not necessary to show traffic by IP, by protocol/application, or by time of day. They just need an overall week to week, month to month, trend line. I'm familiar with MRTG/PRTG/tools that collect SNMP data from the router, but the libraries don't have the expertise for the configuration. I've considered installing the tomato firmware on some cheap home/home office routers, but if there's a commercial product that can be purchased that would be significantly simpler. Also the library boards would be much more likely to approve the purchase of a commercial product over a 'hacked' one. Any assistance would be appreciated.

    Read the article

  • Setting Up Apache as a Forward Proxy with Cahcing

    - by Karl
    I am trying to set up Apache as a forward proxy with caching, but it does not seem to be working correctly. Getting Apache working as a forward proxy was no problem, but no matter what I do it is not caching anything, to disk or memory. I already checked to make sure nothing is conflicting in the mods_enabled directory with mod_cache (ended up commenting it all out) and also I tried moving all of the caching related fields to the configuration file for mod_cache. In addition I set up logging for caching requests, but nothing is being written to those logs. Below is my Apache config, any help would be greatly appreciated!! <VIRTUALHOST *:8080> ProxyRequests On ProxyVia On #ErrorLog "/var/log/apache2/proxy-error.log" #CustomLog "/var/log/apache2/proxy-access.log" common CustomLog "/var/log/apache2/cached-requests.log" common env=cache-hit CustomLog "/var/log/apache2/uncached-requests.log" common env=cache-miss CustomLog "/var/log/apache2/revalidated-requests.log" common env=cache-revalidate CustomLog "/var/log/apache2/invalidated-requests.log" common env=cache-invalidate LogFormat "%{cache-status}e ..." # This path must be the same as the one in /etc/default/apache2 CacheRoot /var/cache/apache2/mod_disk_cache # This will also cache local documents. It usually makes more sense to # put this into the configuration for just one virtual host. CacheEnable disk / #CacheHeader on CacheDirLevels 3 CacheDirLength 5 ##<IfModule mod_mem_cache.c> # CacheEnable mem / # MCacheSize 4096 # MCacheMaxObjectCount 100 # MCacheMinObjectSize 1 # MCacheMaxObjectSize 2048 #</IfModule> <Proxy *> Order deny,allow Deny from all Allow from x.x.x.x #IP above hidden for this post <filesMatch "\.(xml|txt|html|js|css)$"> ExpiresDefault A7200 Header append Cache-Control "proxy-revalidate" </filesMatch> </Proxy> </VIRTUALHOST> Thank you once again!

    Read the article

  • Microsoft Web Farm Framework 502 error

    - by hermiod
    My apologies if this is a really stupid question, but I have installed and set up the new Microsoft Web Farm Framework in a UAT environment with a controller machine, a primary, and a secondary server. I have installed one of our in-house applications on to the primary server and it has been successfully provisioned across to the secondary. I have tried accessing the server via the url http:\mis-uat-002\testfarm\reviewer where mis-uat-002 is the name of the farm controller, testfarm is the name of the farm, and reviewer is the name of the application. When using this url I get a "502 - Web server received an invalid response while acting as a gateway or proxy server." error. If I access the application directly via http:\mis-uat-003\reviewer (mis-uat-003 is the primary farm server, reviewer is the application) then it works no problem. Is there some additional set up that needs to be done in order for the farm controller to do its job? It should be noted that this is a UAT environment so is not on a domain of any sort. However, if this was successful and the WFF came out with V1.0 fairly soon, we would be looking to run this on a Windows 2008 domain.

    Read the article

  • Boinc permissions problem on OS X

    - by Erik Vold
    I installed boinc 6.10.21 on my OS X 10.5 in order to upgrade from a 6.6 version that I was running today, and I am the admin user, and I was logged in as the admin user. As I was installing 6.10.21 I was asked if non admin users should be allowed to use Boinc, and I said 'yes' to this. Then when I tried to open Boinc I got a message like the following: "You currently are not authorized to manage the client. Either re-install and allow non-admin users or contact your administrator to add you to the 'boinc_master' user group." So I tried to reinstall first, and I was not asked if non admin users should be allowed to use Boinc.. so I retried a few times and got no different result.. So I downloaded 6.10.43 and installed that, and again I was not asked if non admin users should be allowed to use boinc.. and when I tried to run Boinc I got the same message like: "You currently are not authorized to manage the client. Either re-install and allow non-admin users or contact your administrator to add you to the 'boinc_master' user group." So I did a Google search trying to figure out how to add my admin user to the bonic_master user group and found this which suggested I run the following in terminal: "sudo dscl . -append /Groups/boinc_master GroupMembership <your user's short name> CR" So I did this and now I get the following error: BOINC ownership or permissions are not set properly; please reinstall BOINC (Error code -1200) So I reinstall and I am ever asked the question about allowing non admin users again, and I still get this error message every after every reinstall attempt.. What should I do?..

    Read the article

< Previous Page | 517 518 519 520 521 522 523 524 525 526 527 528  | Next Page >