Search Results

Search found 22267 results on 891 pages for 'org mode'.

Page 528/891 | < Previous Page | 524 525 526 527 528 529 530 531 532 533 534 535  | Next Page >

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Multiple connections to the same Wireless Network in Windows 7

  - by Jamek

  Hello, my university just limited bandwidth to 512 kbps (that's 64 kB/s!) for each connection. I was thinking to make multiple connection to the same wireless network (called "internet"), is this possible under Windows 7? I know it's possible to connect to more than one WLAN through the "hostednetwork" concept in netsh: netsh wlan set hostednetwork mode=allow ssid=xxxxx netsh wlan start hostednetwork However this method doesn't seem to work, I don't know if it's due to the authentication method (through certificates while hostednetwork seems to support just a "passphrase") or because I'm already connected to that network with the same MAC. Can you think to some tool able to do this?

  Read the article

• Block ip for long time

  - by Tiziano Dan

  This question is about a iptables, I wanna to know how can I block these ip for 1hour and not only a little time.. because they make to many sql requests, I'm using it for block but it's not enough because there's anyway 100k ip who attack then too much requests for sql server. iptables -N SYN-LIMIT iptables -A SYN-LIMIT -m hashlimit --hashlimit 8/second --hashlimit-mode srcip --hashlimit-name SYN-LIMIT -j RETURN iptables -A SYN-LIMIT -j DROP iptables -I INPUT -p tcp --dport 80 --syn -j SYN-LIMIT iptables -I INPUT -p tcp --dport 80 -m connlimit --connlimit-above 6 -j REJECT --reject-with tcp-reset How can I make the same but block IP for long time ? (Not manually !)

  Read the article

• Creating a portable PHP install?

  - by Xeoncross

  I would like to create a folder with a couple versions of PHP that I can start in cgi mode as needed. I use different windows machines for development and I would like to be able to move around computers without needing to install PHP on each one. Something like below F:/PHP /5.3.2 /5.2.8 /5.1.0 Then I could just start each up as needed with something like F:\php\5.3.2\php-cgi.exe -b 127.0.0.1:9000 Which would allow nginx or apache to use the PHP service. This would really help to make my development environment decoupled. Does anyone know how to create a portable PHP install?

  Read the article

• Installing GPSBabel on CentOS 5 x86_64

  - by Clint Chaney

  Well first let me say I have no clue about doing anything on my server, I ask my host to do all installs for me. I run a website where users store latitude and longitude coordinates in my database. I would like them to be able to download these waypoints to their gps units. I found a program called GPSBabel that allows this to be done. http://www.gpsbabel.org/ I want to be able to control GPSBabel from PHP using exec() or something along those lines. The problem is that the linux version of the program is a source file and they don't want to build or install it without some source of instructions. Does anyone have experience with installing this? Perhaps know someone that has and that can lead me in the right direction? Any help would be hugely appreciated. I'm pretty much stuck without getting this to work.

  Read the article

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• Samba domain trust errors on a specific interface

  - by John K

  We have a windows domain that also has RHEL member servers in it. All the servers have a primary network connection to the LAN, but some servers also have private dedicated links to one of our RHEL servers, which serves as a head to our SAN storage. This particular server is running Samba 3.5.15, and is running in domain authentication mode. Users can access shares on this server without a problem over the LAN connection from our Windows servers, but if a user tries to access the shares over a private link (i.e. a 192.168.1.2 address to the RHEL server) users get an error "The trust relationship between this workstation and the primary domain failed."

  Read the article

• Distributing a Python Software for Linux [closed]

  - by zfranciscus

  Hi, I am writing my first software in Python for Ubuntu (or Debian based Linux). I am looking for a good advise on the best way to distribute my software. The easist alternative that I can think of at the moment is to archive the python code into *.tar.gz, and let user execute the main python script as an executable to run the software. I realize that this may not be the best approach. I looked at the Debian maintainer guide: "http://www.debian.org/doc/maint-guide/ch-dother.en.html", not too sound lazy, but the guide looks very intimidating for a beginner. Are there any other tutorial that show how to create a debian package for a beginner ? If anyone has a suggestion do let me know. Thanks ^_^

  Read the article

• Xen DomU does not have network connectivity

  - by Prakashkumar Thiagarajan

  I am trying to install Xen on my Fedora box. Dom0 image has network connectivity. But when I try to create a DomU, it does not have network connectivity. I want to be able to run in bridged mode. I have the /etc/xend/xend-config.sxp file accordingly. My config file looks like kernel = "/boot/vmlinuz-2.6.18-xenU" memory = 64 name = "clientA" vif = ['bridge=xenbr0,mac=12.34.56.78.9A.BC'] root = "/dev/sda1 ro" ramdisk = "/boot/initrd-linux.img" extra = "ro selinux=0.3 initcall_debug" features = 'auto_translated_physmap' Am I missing something ?

  Read the article

• How to add a service to the S runlevel in Debian?

  - by MasterM

  I have the following script (what it does exactly is not important): #!/bin/sh -e ### BEGIN INIT INFO # Provides: watchdog_early # Required-Start: udev # Required-Stop: # Default-Start: S # Default-Stop: # X-Interactive: true # Short-Description: Start watchdog early. ### END INIT INFO # Do stuff here... I insert it into the S runlevel by invoking: insserv watchdog_early The aproriate link is created in /etc/rcS.d: S04watchdog_early -> ../init.d/watchdog_early and /etc/init.d/watchdog_early is executable (has mode 755). Despite all this, it is NOT being run at boot. Why?

  Read the article

• how do I use tar -C on Snow Leopard when creating an archive ?

  - by ssc

  The man page states -C directory In c and r mode, this changes the directory before adding the following files. However, tar does not change to the directory I specify, but instead reports tar: <folder name>: Cannot stat: No such file or directory for every folder in the directory I run the tar command in. Do I really have to do something like cd <folder> && tar ... && cd - or is there a way to get this work ?

  Read the article

• What causes an MSI package to launch following application install

  - by Damo

  We have an application we have developed, it gets deployed via an MSI I built. The MSI has been used in many locations, on many different builds. On one customers site, on occasion we are seeing some odd occurrences of data from the registry going missing. The 'data' from some select registry keys disappears and we have little idea why. One interesting point is that the MSI installer for our application has been seen in passive mode during OS load / load of our application on stat-up. The MSI loads a progress bar then disappears, following this our application loads up. It has been noted that following this the data disappears from our registry. However I can't say these two events are absolutely linked, it could have been missing before this event. What causes the MSI for an application to launch way after initial installation. How can it be prevented (correctly)

  Read the article

• How do you know where macports installs python packages to?

  - by xmaslist

  I am running macports to install scipy and such on OS X leopard with python 2.7. The install runs successfully, but running python and trying to import the packages I've installed, they're not found. What I'm running is: sudo python_select python27 sudo port install py27-wxpython py27-numpy py27-matplotlib sudo port install py27-scipy py27-ipython Opening up python in interactive mode (it is the correct version of python), I type 'import scipy' and get a module not found error. What gives? How can I find out where it is installing the packages to instead?

  Read the article

• Windows Explorer not responding

  - by William Barnes

  I am running W7 64bit on an AMD Quad 1.8Ghz processor. I have a 500GB system drive and added a 1TB drive. Windows Explorer does it's "not responding" thing regularly. I read the other posts and ran SCANNOW and it came back clean. I also ran AUTORUNS and disabled everything that was not windows related. No luck. I booted in safe mode and it appears that explorer works, but I don't know why. I did read a post awhile back that it could be a Service program that makes explorer not respond. I forgot to bookmark the site and don't remember how to turn off the SP's without crashing the entire system. Any help or suggestions will be appreciated. I have also run CHKDSK on all drives, and there were no errors found. EDIT: It has been in for about 2 years and the problem started about 4 or 5 months ago.

  Read the article

• Can GNU sed (for Windows) handle Unicode? If so, is it a code-page/locale issue, or a switch?

  - by Peter.O

  I've been using GNU SED on and off for a couple of years now. It spins me out a bit sometimes, but it does a good job... for single-byte char sets! I now and then notice references to GNU SED being Unicode-aware, but the closest I've seen of this is its "binary" mode.. and binary is not Unicode. Can GSED process a Unicode text file at CodePoint resolution, including and especially \r\n (Windows)... and if it can, does it expect UTF-8, UTF-16, or what? and how does SED detect the encoding?

  Read the article

• How can I prevent a Windows laptop from making noise when starting up?

  - by Walkerneo

  I have a Windows 7 laptop here that makes a noise each time it starts up. I know I can disable that noise now that I'm logged on, but how could I have prevented it WHILE logging on? I remember that there was one of the function keys (F8?) that would allow you to boot into safe mode, but is there a key that will stop the startup sound? Imagine, for example, having your laptop in the library when you know the volume is all the way up - how could you log into your computer without disturbing everyone else?

  Read the article

• Can I copy from vim to another window without +xterm-clipboard?

  - by GorillaSandwich

  I'm using Ubuntu and vim. I can copy text from vim and paste it into another window by highlighting it in vim, then middle-clicking in the other window. This works fine when I'm on my local machine. I can also copy into the system register by highlighting text and yanking to the system register. (For example, Shift-V JJ "+ y to go into linewise visual mode, highlight two lines, select the '+' register and yank.) It's then available to paste into other windows. However, if I ssh into my web host, I can't do either of these. (They use some flavor of Linux - I think it's CentOS.) In vim, if I type :version, my local version shows +xterm_clipboard, but the host's version shows -xterm_clipboard. I don't have sudo rights there. Is there any way to be able to copy from their vim without getting them to tinker with the installation?

  Read the article

• Which universal or driverless printing solution do you use/recommend?

  - by Matt

  I'm in need of a driverless printing solution for Microsoft Terminal Services 2003/2008. This is mainly to support clients who are connected through broadband into our hosted servers. We were hoping that MSTS 2008 thinprint would be the answer but unfortunately it performs poorly in the print area. The files are too large. I found the following slightly outdated URL: http://www.msterminalservices.org/software/Printing/ This lists a number of products but I have no experience with any of them. I'd like a product that works/easy to install (as our clients are remote and not particularly tech savvy) and ideally I just pay for the server license and not every clients. What is your experience/recommendation and tips you can offer me in regards to TS printing? thanks in advance.

  Read the article

• Apollo linux boot into single user

  - by Spirit

  We have a device that runs Appolo Linux and I have to boot that device into a single user mode so that i can run a fsck to check the hard drive for errors. I've been goggling this during the past hour and so far I haven't found any specific method on how can I do that on this version on Linux. The device is known formerly as a NFX Cinxi One - now re-branded into BlackStratus LOG Storm. If any of you have any experience with this one you may know it is a device that is used to collect logs from other servers. I know that the above info isn't much but that is everything that I can provide up until now since tomorrow I have to follow up closely on this problem.

  Read the article

• USB-keyboard & mouse powered off in windows-7

  - by sinned

  I have a problem with a pc where usb devices are not getting any power as soon as windows starts up (it works in preboot). This pc has no ps/2, so there is no chance for input, also not in secure boot mode. I "tidied up" using sysinternals autostart, so there is a chance I messed something up here, although I'm quite sure I only deleted some old printer drivers from autostart. I do not know how to reset this, I cant even log in because there is no input possible. I could use a linux live cd, but I don't know what to do there because there is no sysinternals from linux into a not running windows... To make things even worse, I have the windows installation completely encrypted with truecrypt, so I haven't even tried windows recovery cd yet. There is no loss of data since I can access the disc with a live-linux, I only want to use it again without resetting up everything. Any suggestions?

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

• HP Wireless Printer not working

  - by Omri Spector

  I have installed an HP DeskJet 4620 driver on a win 7 machine. All works perfectly for several days, and than printing is not longer possible. Instead I get the message: "Unable to communicate with printer". This happened on every Win 7 PC I tried, and none of the HP/MS sites contain any relevant info... (Posting this so that the answer appears online, as I did solve it after much work) Solution: It appears that HP installation puts a unique "port" called "HP Network re-discovery". It stops working after some time (possibly after the first time the printer/pc enter sleep mode). BUT, the standard MS TCP port works just fine. So: Go to "Printers" Right click Printer Click "Printer properties" and then "Printer" or "Fax" (for both - do all this twice) Click "Add Port..." Select "Standard TCP Port" Fill in details Move printer to use the new port by un-checking the old one and checking the new one Happy printing.

  Read the article

• Is it possible to kill a RAS connection which won't disconnect.

  - by sgmoore

  I have a Windows 2003 Server which has a number or RAS Connections to some of our customers. Occasionally the connections go into a mode where there are connected, but not working. Disconnecting and reconnecting solves the problem. However sometimes you can not disconnect as I get the following error message It is not possible to disconnect at this time. The connection is currently busy with a connect or disconnect operation. There are no visible connection dialog boxes when this message occurs and I usually end up having to restart the server which obviously affects all the other users. I know that if you have a service that is stuck 'stopping' you can just kill it. Is there anything similar that you can do to reset a ras connection?

  Read the article

• Problem with running a program from flashdrive

  - by rajivpradeep

  I have a USB drive with two partitions in it, one hidden and one normal. I have an application which swaps the memory and runs the flash application in hidden zone. The problem is that the application works fine on Windows 7 and when run on Win XP, it swaps the partitions but doesn't run the flash applications but just keeps running in the background. I can see it in task manager. But, when I copy the application to desktop and run, it runs with no glitch. I was facing the same problem on Win 7 too, but it was running as required when I ran it using "Run in XP mode" and then I applied a SHIM and is running since then as required. The application is built using VC++ 2008. does anyone know the solution?

  Read the article

• Problem with running a program from flashdrive

  - by rajivpradeep

  I have a USB drive with two partitions in it, one hidden and one normal. I have an application which swaps the memory and runs the flash application in hidden zone. The problem is that the application works fine on Windows 7 and when run on Win XP, it swaps the partitions but doesn't run the flash applications but just keeps running in the background. I can see it in task manager. But, when I copy the application to desktop and run, it runs with no glitch. I was facing the same problem on Win 7 too, but it was running as required when I ran it using "Run in XP mode" and then I applied a SHIM and is running since then as required. The application is built using VC++ 2008. does anyone know the solution?

  Read the article

< Previous Page | 524 525 526 527 528 529 530 531 532 533 534 535  | Next Page >